blob: ac08a09c64c28c2675b5d327469bfb2f0a4030e6 [file] [log] [blame]
// SPDX-License-Identifier: BSD-3-Clause
/*
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved.
* Copyright (c) 2019, Linaro Limited
*/
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pm8150l-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pm8150l_temp>;
trips {
trip0 {
temperature = <95000>;
hysteresis = <0>;
type = "passive";
};
trip1 {
temperature = <115000>;
hysteresis = <0>;
type = "hot";
};
trip2 {
temperature = <145000>;
hysteresis = <0>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pmic@4 {
compatible = "qcom,pm8150l", "qcom,spmi-pmic";
reg = <0x4 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pon@800 {
compatible = "qcom,pm8916-pon";
reg = <0x0800>;
status = "disabled";
};
pm8150l_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
io-channels = <&pm8150l_adc ADC5_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pm8150l_adc: adc@3100 {
compatible = "qcom,spmi-adc5";
reg = <0x3100>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
channel@0 {
reg = <ADC5_REF_GND>;
qcom,pre-scaling = <1 1>;
label = "ref_gnd";
};
channel@1 {
reg = <ADC5_1P25VREF>;
qcom,pre-scaling = <1 1>;
label = "vref_1p25";
};
channel@6 {
reg = <ADC5_DIE_TEMP>;
qcom,pre-scaling = <1 1>;
label = "die_temp";
};
};
pm8150l_adc_tm: adc-tm@3500 {
compatible = "qcom,spmi-adc-tm5";
reg = <0x3500>;
interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>;
#thermal-sensor-cells = <1>;
#address-cells = <1>;
#size-cells = <0>;
status = "disabled";
};
pm8150l_gpios: gpio@c000 {
compatible = "qcom,pm8150l-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
gpio-ranges = <&pm8150l_gpios 0 0 12>;
#gpio-cells = <2>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pmic@5 {
compatible = "qcom,pm8150l", "qcom,spmi-pmic";
reg = <0x5 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pm8150l_flash: led-controller@d300 {
compatible = "qcom,pm8150l-flash-led", "qcom,spmi-flash-led";
reg = <0xd300>;
status = "disabled";
};
pm8150l_lpg: pwm {
compatible = "qcom,pm8150l-lpg";
#address-cells = <1>;
#size-cells = <0>;
#pwm-cells = <2>;
status = "disabled";
};
pm8150l_wled: leds@d800 {
compatible = "qcom,pm8150l-wled";
reg = <0xd800>, <0xd900>;
interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>,
<0x5 0xd8 0x2 IRQ_TYPE_EDGE_RISING>;
interrupt-names = "ovp", "short";
label = "backlight";
status = "disabled";
};
};
};