| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright (c) 2016 Allwinnertech Co., Ltd. |
| * Copyright (C) 2017-2018 Bootlin |
| * |
| * Maxime Ripard <maxime.ripard@bootlin.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/component.h> |
| #include <linux/crc-ccitt.h> |
| #include <linux/module.h> |
| #include <linux/of_address.h> |
| #include <linux/phy/phy-mipi-dphy.h> |
| #include <linux/phy/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/regmap.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/slab.h> |
| |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_panel.h> |
| #include <drm/drm_print.h> |
| #include <drm/drm_probe_helper.h> |
| #include <drm/drm_simple_kms_helper.h> |
| |
| #include "sun4i_crtc.h" |
| #include "sun4i_tcon.h" |
| #include "sun6i_mipi_dsi.h" |
| |
| #include <video/mipi_display.h> |
| |
| #define SUN6I_DSI_CTL_REG 0x000 |
| #define SUN6I_DSI_CTL_EN BIT(0) |
| |
| #define SUN6I_DSI_BASIC_CTL_REG 0x00c |
| #define SUN6I_DSI_BASIC_CTL_TRAIL_INV(n) (((n) & 0xf) << 4) |
| #define SUN6I_DSI_BASIC_CTL_TRAIL_FILL BIT(3) |
| #define SUN6I_DSI_BASIC_CTL_HBP_DIS BIT(2) |
| #define SUN6I_DSI_BASIC_CTL_HSA_HSE_DIS BIT(1) |
| #define SUN6I_DSI_BASIC_CTL_VIDEO_BURST BIT(0) |
| |
| #define SUN6I_DSI_BASIC_CTL0_REG 0x010 |
| #define SUN6I_DSI_BASIC_CTL0_HS_EOTP_EN BIT(18) |
| #define SUN6I_DSI_BASIC_CTL0_CRC_EN BIT(17) |
| #define SUN6I_DSI_BASIC_CTL0_ECC_EN BIT(16) |
| #define SUN6I_DSI_BASIC_CTL0_INST_ST BIT(0) |
| |
| #define SUN6I_DSI_BASIC_CTL1_REG 0x014 |
| #define SUN6I_DSI_BASIC_CTL1_VIDEO_ST_DELAY(n) (((n) & 0x1fff) << 4) |
| #define SUN6I_DSI_BASIC_CTL1_VIDEO_FILL BIT(2) |
| #define SUN6I_DSI_BASIC_CTL1_VIDEO_PRECISION BIT(1) |
| #define SUN6I_DSI_BASIC_CTL1_VIDEO_MODE BIT(0) |
| |
| #define SUN6I_DSI_BASIC_SIZE0_REG 0x018 |
| #define SUN6I_DSI_BASIC_SIZE0_VBP(n) (((n) & 0xfff) << 16) |
| #define SUN6I_DSI_BASIC_SIZE0_VSA(n) ((n) & 0xfff) |
| |
| #define SUN6I_DSI_BASIC_SIZE1_REG 0x01c |
| #define SUN6I_DSI_BASIC_SIZE1_VT(n) (((n) & 0xfff) << 16) |
| #define SUN6I_DSI_BASIC_SIZE1_VACT(n) ((n) & 0xfff) |
| |
| #define SUN6I_DSI_INST_FUNC_REG(n) (0x020 + (n) * 0x04) |
| #define SUN6I_DSI_INST_FUNC_INST_MODE(n) (((n) & 0xf) << 28) |
| #define SUN6I_DSI_INST_FUNC_ESCAPE_ENTRY(n) (((n) & 0xf) << 24) |
| #define SUN6I_DSI_INST_FUNC_TRANS_PACKET(n) (((n) & 0xf) << 20) |
| #define SUN6I_DSI_INST_FUNC_LANE_CEN BIT(4) |
| #define SUN6I_DSI_INST_FUNC_LANE_DEN(n) ((n) & 0xf) |
| |
| #define SUN6I_DSI_INST_LOOP_SEL_REG 0x040 |
| |
| #define SUN6I_DSI_INST_LOOP_NUM_REG(n) (0x044 + (n) * 0x10) |
| #define SUN6I_DSI_INST_LOOP_NUM_N1(n) (((n) & 0xfff) << 16) |
| #define SUN6I_DSI_INST_LOOP_NUM_N0(n) ((n) & 0xfff) |
| |
| #define SUN6I_DSI_INST_JUMP_SEL_REG 0x048 |
| |
| #define SUN6I_DSI_INST_JUMP_CFG_REG(n) (0x04c + (n) * 0x04) |
| #define SUN6I_DSI_INST_JUMP_CFG_TO(n) (((n) & 0xf) << 20) |
| #define SUN6I_DSI_INST_JUMP_CFG_POINT(n) (((n) & 0xf) << 16) |
| #define SUN6I_DSI_INST_JUMP_CFG_NUM(n) ((n) & 0xffff) |
| |
| #define SUN6I_DSI_TRANS_START_REG 0x060 |
| |
| #define SUN6I_DSI_TRANS_ZERO_REG 0x078 |
| |
| #define SUN6I_DSI_TCON_DRQ_REG 0x07c |
| #define SUN6I_DSI_TCON_DRQ_ENABLE_MODE BIT(28) |
| #define SUN6I_DSI_TCON_DRQ_SET(n) ((n) & 0x3ff) |
| |
| #define SUN6I_DSI_PIXEL_CTL0_REG 0x080 |
| #define SUN6I_DSI_PIXEL_CTL0_PD_PLUG_DISABLE BIT(16) |
| #define SUN6I_DSI_PIXEL_CTL0_FORMAT(n) ((n) & 0xf) |
| |
| #define SUN6I_DSI_PIXEL_CTL1_REG 0x084 |
| |
| #define SUN6I_DSI_PIXEL_PH_REG 0x090 |
| #define SUN6I_DSI_PIXEL_PH_ECC(n) (((n) & 0xff) << 24) |
| #define SUN6I_DSI_PIXEL_PH_WC(n) (((n) & 0xffff) << 8) |
| #define SUN6I_DSI_PIXEL_PH_VC(n) (((n) & 3) << 6) |
| #define SUN6I_DSI_PIXEL_PH_DT(n) ((n) & 0x3f) |
| |
| #define SUN6I_DSI_PIXEL_PF0_REG 0x098 |
| #define SUN6I_DSI_PIXEL_PF0_CRC_FORCE(n) ((n) & 0xffff) |
| |
| #define SUN6I_DSI_PIXEL_PF1_REG 0x09c |
| #define SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINEN(n) (((n) & 0xffff) << 16) |
| #define SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINE0(n) ((n) & 0xffff) |
| |
| #define SUN6I_DSI_SYNC_HSS_REG 0x0b0 |
| |
| #define SUN6I_DSI_SYNC_HSE_REG 0x0b4 |
| |
| #define SUN6I_DSI_SYNC_VSS_REG 0x0b8 |
| |
| #define SUN6I_DSI_SYNC_VSE_REG 0x0bc |
| |
| #define SUN6I_DSI_BLK_HSA0_REG 0x0c0 |
| |
| #define SUN6I_DSI_BLK_HSA1_REG 0x0c4 |
| #define SUN6I_DSI_BLK_PF(n) (((n) & 0xffff) << 16) |
| #define SUN6I_DSI_BLK_PD(n) ((n) & 0xff) |
| |
| #define SUN6I_DSI_BLK_HBP0_REG 0x0c8 |
| |
| #define SUN6I_DSI_BLK_HBP1_REG 0x0cc |
| |
| #define SUN6I_DSI_BLK_HFP0_REG 0x0d0 |
| |
| #define SUN6I_DSI_BLK_HFP1_REG 0x0d4 |
| |
| #define SUN6I_DSI_BLK_HBLK0_REG 0x0e0 |
| |
| #define SUN6I_DSI_BLK_HBLK1_REG 0x0e4 |
| |
| #define SUN6I_DSI_BLK_VBLK0_REG 0x0e8 |
| |
| #define SUN6I_DSI_BLK_VBLK1_REG 0x0ec |
| |
| #define SUN6I_DSI_BURST_LINE_REG 0x0f0 |
| #define SUN6I_DSI_BURST_LINE_SYNC_POINT(n) (((n) & 0xffff) << 16) |
| #define SUN6I_DSI_BURST_LINE_NUM(n) ((n) & 0xffff) |
| |
| #define SUN6I_DSI_BURST_DRQ_REG 0x0f4 |
| #define SUN6I_DSI_BURST_DRQ_EDGE1(n) (((n) & 0xffff) << 16) |
| #define SUN6I_DSI_BURST_DRQ_EDGE0(n) ((n) & 0xffff) |
| |
| #define SUN6I_DSI_CMD_CTL_REG 0x200 |
| #define SUN6I_DSI_CMD_CTL_RX_OVERFLOW BIT(26) |
| #define SUN6I_DSI_CMD_CTL_RX_FLAG BIT(25) |
| #define SUN6I_DSI_CMD_CTL_TX_FLAG BIT(9) |
| |
| #define SUN6I_DSI_CMD_RX_REG(n) (0x240 + (n) * 0x04) |
| |
| #define SUN6I_DSI_DEBUG_DATA_REG 0x2f8 |
| |
| #define SUN6I_DSI_CMD_TX_REG(n) (0x300 + (n) * 0x04) |
| |
| #define SUN6I_DSI_SYNC_POINT 40 |
| |
| enum sun6i_dsi_start_inst { |
| DSI_START_LPRX, |
| DSI_START_LPTX, |
| DSI_START_HSC, |
| DSI_START_HSD, |
| }; |
| |
| enum sun6i_dsi_inst_id { |
| DSI_INST_ID_LP11 = 0, |
| DSI_INST_ID_TBA, |
| DSI_INST_ID_HSC, |
| DSI_INST_ID_HSD, |
| DSI_INST_ID_LPDT, |
| DSI_INST_ID_HSCEXIT, |
| DSI_INST_ID_NOP, |
| DSI_INST_ID_DLY, |
| DSI_INST_ID_END = 15, |
| }; |
| |
| enum sun6i_dsi_inst_mode { |
| DSI_INST_MODE_STOP = 0, |
| DSI_INST_MODE_TBA, |
| DSI_INST_MODE_HS, |
| DSI_INST_MODE_ESCAPE, |
| DSI_INST_MODE_HSCEXIT, |
| DSI_INST_MODE_NOP, |
| }; |
| |
| enum sun6i_dsi_inst_escape { |
| DSI_INST_ESCA_LPDT = 0, |
| DSI_INST_ESCA_ULPS, |
| DSI_INST_ESCA_UN1, |
| DSI_INST_ESCA_UN2, |
| DSI_INST_ESCA_RESET, |
| DSI_INST_ESCA_UN3, |
| DSI_INST_ESCA_UN4, |
| DSI_INST_ESCA_UN5, |
| }; |
| |
| enum sun6i_dsi_inst_packet { |
| DSI_INST_PACK_PIXEL = 0, |
| DSI_INST_PACK_COMMAND, |
| }; |
| |
| static const u32 sun6i_dsi_ecc_array[] = { |
| [0] = (BIT(0) | BIT(1) | BIT(2) | BIT(4) | BIT(5) | BIT(7) | BIT(10) | |
| BIT(11) | BIT(13) | BIT(16) | BIT(20) | BIT(21) | BIT(22) | |
| BIT(23)), |
| [1] = (BIT(0) | BIT(1) | BIT(3) | BIT(4) | BIT(6) | BIT(8) | BIT(10) | |
| BIT(12) | BIT(14) | BIT(17) | BIT(20) | BIT(21) | BIT(22) | |
| BIT(23)), |
| [2] = (BIT(0) | BIT(2) | BIT(3) | BIT(5) | BIT(6) | BIT(9) | BIT(11) | |
| BIT(12) | BIT(15) | BIT(18) | BIT(20) | BIT(21) | BIT(22)), |
| [3] = (BIT(1) | BIT(2) | BIT(3) | BIT(7) | BIT(8) | BIT(9) | BIT(13) | |
| BIT(14) | BIT(15) | BIT(19) | BIT(20) | BIT(21) | BIT(23)), |
| [4] = (BIT(4) | BIT(5) | BIT(6) | BIT(7) | BIT(8) | BIT(9) | BIT(16) | |
| BIT(17) | BIT(18) | BIT(19) | BIT(20) | BIT(22) | BIT(23)), |
| [5] = (BIT(10) | BIT(11) | BIT(12) | BIT(13) | BIT(14) | BIT(15) | |
| BIT(16) | BIT(17) | BIT(18) | BIT(19) | BIT(21) | BIT(22) | |
| BIT(23)), |
| }; |
| |
| static u32 sun6i_dsi_ecc_compute(unsigned int data) |
| { |
| int i; |
| u8 ecc = 0; |
| |
| for (i = 0; i < ARRAY_SIZE(sun6i_dsi_ecc_array); i++) { |
| u32 field = sun6i_dsi_ecc_array[i]; |
| bool init = false; |
| u8 val = 0; |
| int j; |
| |
| for (j = 0; j < 24; j++) { |
| if (!(BIT(j) & field)) |
| continue; |
| |
| if (!init) { |
| val = (BIT(j) & data) ? 1 : 0; |
| init = true; |
| } else { |
| val ^= (BIT(j) & data) ? 1 : 0; |
| } |
| } |
| |
| ecc |= val << i; |
| } |
| |
| return ecc; |
| } |
| |
| static u16 sun6i_dsi_crc_compute(u8 const *buffer, size_t len) |
| { |
| return crc_ccitt(0xffff, buffer, len); |
| } |
| |
| static u16 sun6i_dsi_crc_repeat(u8 pd, u8 *buffer, size_t len) |
| { |
| memset(buffer, pd, len); |
| |
| return sun6i_dsi_crc_compute(buffer, len); |
| } |
| |
| static u32 sun6i_dsi_build_sync_pkt(u8 dt, u8 vc, u8 d0, u8 d1) |
| { |
| u32 val = dt & 0x3f; |
| |
| val |= (vc & 3) << 6; |
| val |= (d0 & 0xff) << 8; |
| val |= (d1 & 0xff) << 16; |
| val |= sun6i_dsi_ecc_compute(val) << 24; |
| |
| return val; |
| } |
| |
| static u32 sun6i_dsi_build_blk0_pkt(u8 vc, u16 wc) |
| { |
| return sun6i_dsi_build_sync_pkt(MIPI_DSI_BLANKING_PACKET, vc, |
| wc & 0xff, wc >> 8); |
| } |
| |
| static u32 sun6i_dsi_build_blk1_pkt(u16 pd, u8 *buffer, size_t len) |
| { |
| u32 val = SUN6I_DSI_BLK_PD(pd); |
| |
| return val | SUN6I_DSI_BLK_PF(sun6i_dsi_crc_repeat(pd, buffer, len)); |
| } |
| |
| static void sun6i_dsi_inst_abort(struct sun6i_dsi *dsi) |
| { |
| regmap_update_bits(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG, |
| SUN6I_DSI_BASIC_CTL0_INST_ST, 0); |
| } |
| |
| static void sun6i_dsi_inst_commit(struct sun6i_dsi *dsi) |
| { |
| regmap_update_bits(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG, |
| SUN6I_DSI_BASIC_CTL0_INST_ST, |
| SUN6I_DSI_BASIC_CTL0_INST_ST); |
| } |
| |
| static int sun6i_dsi_inst_wait_for_completion(struct sun6i_dsi *dsi) |
| { |
| u32 val; |
| |
| return regmap_read_poll_timeout(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG, |
| val, |
| !(val & SUN6I_DSI_BASIC_CTL0_INST_ST), |
| 100, 5000); |
| } |
| |
| static void sun6i_dsi_inst_setup(struct sun6i_dsi *dsi, |
| enum sun6i_dsi_inst_id id, |
| enum sun6i_dsi_inst_mode mode, |
| bool clock, u8 data, |
| enum sun6i_dsi_inst_packet packet, |
| enum sun6i_dsi_inst_escape escape) |
| { |
| regmap_write(dsi->regs, SUN6I_DSI_INST_FUNC_REG(id), |
| SUN6I_DSI_INST_FUNC_INST_MODE(mode) | |
| SUN6I_DSI_INST_FUNC_ESCAPE_ENTRY(escape) | |
| SUN6I_DSI_INST_FUNC_TRANS_PACKET(packet) | |
| (clock ? SUN6I_DSI_INST_FUNC_LANE_CEN : 0) | |
| SUN6I_DSI_INST_FUNC_LANE_DEN(data)); |
| } |
| |
| static void sun6i_dsi_inst_init(struct sun6i_dsi *dsi, |
| struct mipi_dsi_device *device) |
| { |
| u8 lanes_mask = GENMASK(device->lanes - 1, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_LP11, DSI_INST_MODE_STOP, |
| true, lanes_mask, 0, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_TBA, DSI_INST_MODE_TBA, |
| false, 1, 0, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSC, DSI_INST_MODE_HS, |
| true, 0, DSI_INST_PACK_PIXEL, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSD, DSI_INST_MODE_HS, |
| false, lanes_mask, DSI_INST_PACK_PIXEL, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_LPDT, DSI_INST_MODE_ESCAPE, |
| false, 1, DSI_INST_PACK_COMMAND, |
| DSI_INST_ESCA_LPDT); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_HSCEXIT, DSI_INST_MODE_HSCEXIT, |
| true, 0, 0, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_NOP, DSI_INST_MODE_STOP, |
| false, lanes_mask, 0, 0); |
| |
| sun6i_dsi_inst_setup(dsi, DSI_INST_ID_DLY, DSI_INST_MODE_NOP, |
| true, lanes_mask, 0, 0); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_CFG_REG(0), |
| SUN6I_DSI_INST_JUMP_CFG_POINT(DSI_INST_ID_NOP) | |
| SUN6I_DSI_INST_JUMP_CFG_TO(DSI_INST_ID_HSCEXIT) | |
| SUN6I_DSI_INST_JUMP_CFG_NUM(1)); |
| }; |
| |
| static u16 sun6i_dsi_get_video_start_delay(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| u16 delay = mode->vtotal - (mode->vsync_start - mode->vdisplay) + 1; |
| |
| if (delay > mode->vtotal) |
| delay = delay % mode->vtotal; |
| |
| return max_t(u16, delay, 1); |
| } |
| |
| static u16 sun6i_dsi_get_line_num(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8; |
| |
| return mode->htotal * Bpp / device->lanes; |
| } |
| |
| static u16 sun6i_dsi_get_drq_edge0(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode, |
| u16 line_num, u16 edge1) |
| { |
| u16 edge0 = edge1; |
| |
| edge0 += (mode->hdisplay + 40) * SUN6I_DSI_TCON_DIV / 8; |
| |
| if (edge0 > line_num) |
| return edge0 - line_num; |
| |
| return 1; |
| } |
| |
| static u16 sun6i_dsi_get_drq_edge1(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode, |
| u16 line_num) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| unsigned int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8; |
| unsigned int hbp = mode->htotal - mode->hsync_end; |
| u16 edge1; |
| |
| edge1 = SUN6I_DSI_SYNC_POINT; |
| edge1 += (mode->hdisplay + hbp + 20) * Bpp / device->lanes; |
| |
| if (edge1 > line_num) |
| return line_num; |
| |
| return edge1; |
| } |
| |
| static void sun6i_dsi_setup_burst(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| u32 val = 0; |
| |
| if (device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) { |
| u16 line_num = sun6i_dsi_get_line_num(dsi, mode); |
| u16 edge0, edge1; |
| |
| edge1 = sun6i_dsi_get_drq_edge1(dsi, mode, line_num); |
| edge0 = sun6i_dsi_get_drq_edge0(dsi, mode, line_num, edge1); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BURST_DRQ_REG, |
| SUN6I_DSI_BURST_DRQ_EDGE0(edge0) | |
| SUN6I_DSI_BURST_DRQ_EDGE1(edge1)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BURST_LINE_REG, |
| SUN6I_DSI_BURST_LINE_NUM(line_num) | |
| SUN6I_DSI_BURST_LINE_SYNC_POINT(SUN6I_DSI_SYNC_POINT)); |
| |
| val = SUN6I_DSI_TCON_DRQ_ENABLE_MODE; |
| } else if ((mode->hsync_start - mode->hdisplay) > 20) { |
| /* Maaaaaagic */ |
| u16 drq = (mode->hsync_start - mode->hdisplay) - 20; |
| |
| drq *= mipi_dsi_pixel_format_to_bpp(device->format); |
| drq /= 32; |
| |
| val = (SUN6I_DSI_TCON_DRQ_ENABLE_MODE | |
| SUN6I_DSI_TCON_DRQ_SET(drq)); |
| } |
| |
| regmap_write(dsi->regs, SUN6I_DSI_TCON_DRQ_REG, val); |
| } |
| |
| static void sun6i_dsi_setup_inst_loop(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| u16 delay = 50 - 1; |
| |
| if (device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) { |
| u32 hsync_porch = (mode->htotal - mode->hdisplay) * 150; |
| |
| delay = (hsync_porch / ((mode->clock / 1000) * 8)); |
| delay -= 50; |
| } |
| |
| regmap_write(dsi->regs, SUN6I_DSI_INST_LOOP_SEL_REG, |
| 2 << (4 * DSI_INST_ID_LP11) | |
| 3 << (4 * DSI_INST_ID_DLY)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_INST_LOOP_NUM_REG(0), |
| SUN6I_DSI_INST_LOOP_NUM_N0(50 - 1) | |
| SUN6I_DSI_INST_LOOP_NUM_N1(delay)); |
| regmap_write(dsi->regs, SUN6I_DSI_INST_LOOP_NUM_REG(1), |
| SUN6I_DSI_INST_LOOP_NUM_N0(50 - 1) | |
| SUN6I_DSI_INST_LOOP_NUM_N1(delay)); |
| } |
| |
| static void sun6i_dsi_setup_format(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| u32 val = SUN6I_DSI_PIXEL_PH_VC(device->channel); |
| u8 dt, fmt; |
| u16 wc; |
| |
| /* |
| * TODO: The format defines are only valid in video mode and |
| * change in command mode. |
| */ |
| switch (device->format) { |
| case MIPI_DSI_FMT_RGB888: |
| dt = MIPI_DSI_PACKED_PIXEL_STREAM_24; |
| fmt = 8; |
| break; |
| case MIPI_DSI_FMT_RGB666: |
| dt = MIPI_DSI_PIXEL_STREAM_3BYTE_18; |
| fmt = 9; |
| break; |
| case MIPI_DSI_FMT_RGB666_PACKED: |
| dt = MIPI_DSI_PACKED_PIXEL_STREAM_18; |
| fmt = 10; |
| break; |
| case MIPI_DSI_FMT_RGB565: |
| dt = MIPI_DSI_PACKED_PIXEL_STREAM_16; |
| fmt = 11; |
| break; |
| default: |
| return; |
| } |
| val |= SUN6I_DSI_PIXEL_PH_DT(dt); |
| |
| wc = mode->hdisplay * mipi_dsi_pixel_format_to_bpp(device->format) / 8; |
| val |= SUN6I_DSI_PIXEL_PH_WC(wc); |
| val |= SUN6I_DSI_PIXEL_PH_ECC(sun6i_dsi_ecc_compute(val)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PH_REG, val); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PF0_REG, |
| SUN6I_DSI_PIXEL_PF0_CRC_FORCE(0xffff)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_PIXEL_PF1_REG, |
| SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINE0(0xffff) | |
| SUN6I_DSI_PIXEL_PF1_CRC_INIT_LINEN(0xffff)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_PIXEL_CTL0_REG, |
| SUN6I_DSI_PIXEL_CTL0_PD_PLUG_DISABLE | |
| SUN6I_DSI_PIXEL_CTL0_FORMAT(fmt)); |
| } |
| |
| static void sun6i_dsi_setup_timings(struct sun6i_dsi *dsi, |
| struct drm_display_mode *mode) |
| { |
| struct mipi_dsi_device *device = dsi->device; |
| int Bpp = mipi_dsi_pixel_format_to_bpp(device->format) / 8; |
| u16 hbp = 0, hfp = 0, hsa = 0, hblk = 0, vblk = 0; |
| u32 basic_ctl = 0; |
| size_t bytes; |
| u8 *buffer; |
| |
| /* Do all timing calculations up front to allocate buffer space */ |
| |
| if (device->mode_flags & MIPI_DSI_MODE_VIDEO_BURST) { |
| hblk = mode->hdisplay * Bpp; |
| basic_ctl = SUN6I_DSI_BASIC_CTL_VIDEO_BURST | |
| SUN6I_DSI_BASIC_CTL_HSA_HSE_DIS | |
| SUN6I_DSI_BASIC_CTL_HBP_DIS; |
| |
| if (device->lanes == 4) |
| basic_ctl |= SUN6I_DSI_BASIC_CTL_TRAIL_FILL | |
| SUN6I_DSI_BASIC_CTL_TRAIL_INV(0xc); |
| } else { |
| /* |
| * A sync period is composed of a blanking packet (4 |
| * bytes + payload + 2 bytes) and a sync event packet |
| * (4 bytes). Its minimal size is therefore 10 bytes |
| */ |
| #define HSA_PACKET_OVERHEAD 10 |
| hsa = max(HSA_PACKET_OVERHEAD, |
| (mode->hsync_end - mode->hsync_start) * Bpp - HSA_PACKET_OVERHEAD); |
| |
| /* |
| * The backporch is set using a blanking packet (4 |
| * bytes + payload + 2 bytes). Its minimal size is |
| * therefore 6 bytes |
| */ |
| #define HBP_PACKET_OVERHEAD 6 |
| hbp = max(HBP_PACKET_OVERHEAD, |
| (mode->htotal - mode->hsync_end) * Bpp - HBP_PACKET_OVERHEAD); |
| |
| /* |
| * The frontporch is set using a sync event (4 bytes) |
| * and two blanking packets (each one is 4 bytes + |
| * payload + 2 bytes). Its minimal size is therefore |
| * 16 bytes |
| */ |
| #define HFP_PACKET_OVERHEAD 16 |
| hfp = max(HFP_PACKET_OVERHEAD, |
| (mode->hsync_start - mode->hdisplay) * Bpp - HFP_PACKET_OVERHEAD); |
| |
| /* |
| * The blanking is set using a sync event (4 bytes) |
| * and a blanking packet (4 bytes + payload + 2 |
| * bytes). Its minimal size is therefore 10 bytes. |
| */ |
| #define HBLK_PACKET_OVERHEAD 10 |
| hblk = max(HBLK_PACKET_OVERHEAD, |
| (mode->htotal - (mode->hsync_end - mode->hsync_start)) * Bpp - |
| HBLK_PACKET_OVERHEAD); |
| |
| /* |
| * And I'm not entirely sure what vblk is about. The driver in |
| * Allwinner BSP is using a rather convoluted calculation |
| * there only for 4 lanes. However, using 0 (the !4 lanes |
| * case) even with a 4 lanes screen seems to work... |
| */ |
| vblk = 0; |
| } |
| |
| /* How many bytes do we need to send all payloads? */ |
| bytes = max_t(size_t, max(max(hfp, hblk), max(hsa, hbp)), vblk); |
| buffer = kmalloc(bytes, GFP_KERNEL); |
| if (WARN_ON(!buffer)) |
| return; |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL_REG, basic_ctl); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_SYNC_HSS_REG, |
| sun6i_dsi_build_sync_pkt(MIPI_DSI_H_SYNC_START, |
| device->channel, |
| 0, 0)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_SYNC_HSE_REG, |
| sun6i_dsi_build_sync_pkt(MIPI_DSI_H_SYNC_END, |
| device->channel, |
| 0, 0)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_SYNC_VSS_REG, |
| sun6i_dsi_build_sync_pkt(MIPI_DSI_V_SYNC_START, |
| device->channel, |
| 0, 0)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_SYNC_VSE_REG, |
| sun6i_dsi_build_sync_pkt(MIPI_DSI_V_SYNC_END, |
| device->channel, |
| 0, 0)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BASIC_SIZE0_REG, |
| SUN6I_DSI_BASIC_SIZE0_VSA(mode->vsync_end - |
| mode->vsync_start) | |
| SUN6I_DSI_BASIC_SIZE0_VBP(mode->vtotal - |
| mode->vsync_end)); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BASIC_SIZE1_REG, |
| SUN6I_DSI_BASIC_SIZE1_VACT(mode->vdisplay) | |
| SUN6I_DSI_BASIC_SIZE1_VT(mode->vtotal)); |
| |
| /* sync */ |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HSA0_REG, |
| sun6i_dsi_build_blk0_pkt(device->channel, hsa)); |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HSA1_REG, |
| sun6i_dsi_build_blk1_pkt(0, buffer, hsa)); |
| |
| /* backporch */ |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HBP0_REG, |
| sun6i_dsi_build_blk0_pkt(device->channel, hbp)); |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HBP1_REG, |
| sun6i_dsi_build_blk1_pkt(0, buffer, hbp)); |
| |
| /* frontporch */ |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HFP0_REG, |
| sun6i_dsi_build_blk0_pkt(device->channel, hfp)); |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HFP1_REG, |
| sun6i_dsi_build_blk1_pkt(0, buffer, hfp)); |
| |
| /* hblk */ |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HBLK0_REG, |
| sun6i_dsi_build_blk0_pkt(device->channel, hblk)); |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_HBLK1_REG, |
| sun6i_dsi_build_blk1_pkt(0, buffer, hblk)); |
| |
| /* vblk */ |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_VBLK0_REG, |
| sun6i_dsi_build_blk0_pkt(device->channel, vblk)); |
| regmap_write(dsi->regs, SUN6I_DSI_BLK_VBLK1_REG, |
| sun6i_dsi_build_blk1_pkt(0, buffer, vblk)); |
| |
| kfree(buffer); |
| } |
| |
| static int sun6i_dsi_start(struct sun6i_dsi *dsi, |
| enum sun6i_dsi_start_inst func) |
| { |
| switch (func) { |
| case DSI_START_LPTX: |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG, |
| DSI_INST_ID_LPDT << (4 * DSI_INST_ID_LP11) | |
| DSI_INST_ID_END << (4 * DSI_INST_ID_LPDT)); |
| break; |
| case DSI_START_LPRX: |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG, |
| DSI_INST_ID_LPDT << (4 * DSI_INST_ID_LP11) | |
| DSI_INST_ID_DLY << (4 * DSI_INST_ID_LPDT) | |
| DSI_INST_ID_TBA << (4 * DSI_INST_ID_DLY) | |
| DSI_INST_ID_END << (4 * DSI_INST_ID_TBA)); |
| break; |
| case DSI_START_HSC: |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG, |
| DSI_INST_ID_HSC << (4 * DSI_INST_ID_LP11) | |
| DSI_INST_ID_END << (4 * DSI_INST_ID_HSC)); |
| break; |
| case DSI_START_HSD: |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG, |
| DSI_INST_ID_NOP << (4 * DSI_INST_ID_LP11) | |
| DSI_INST_ID_HSD << (4 * DSI_INST_ID_NOP) | |
| DSI_INST_ID_DLY << (4 * DSI_INST_ID_HSD) | |
| DSI_INST_ID_NOP << (4 * DSI_INST_ID_DLY) | |
| DSI_INST_ID_END << (4 * DSI_INST_ID_HSCEXIT)); |
| break; |
| default: |
| regmap_write(dsi->regs, SUN6I_DSI_INST_JUMP_SEL_REG, |
| DSI_INST_ID_END << (4 * DSI_INST_ID_LP11)); |
| break; |
| } |
| |
| sun6i_dsi_inst_abort(dsi); |
| sun6i_dsi_inst_commit(dsi); |
| |
| if (func == DSI_START_HSC) |
| regmap_write_bits(dsi->regs, |
| SUN6I_DSI_INST_FUNC_REG(DSI_INST_ID_LP11), |
| SUN6I_DSI_INST_FUNC_LANE_CEN, 0); |
| |
| return 0; |
| } |
| |
| static void sun6i_dsi_encoder_enable(struct drm_encoder *encoder) |
| { |
| struct drm_display_mode *mode = &encoder->crtc->state->adjusted_mode; |
| struct sun6i_dsi *dsi = encoder_to_sun6i_dsi(encoder); |
| struct mipi_dsi_device *device = dsi->device; |
| union phy_configure_opts opts = { }; |
| struct phy_configure_opts_mipi_dphy *cfg = &opts.mipi_dphy; |
| u16 delay; |
| int err; |
| |
| DRM_DEBUG_DRIVER("Enabling DSI output\n"); |
| |
| err = regulator_enable(dsi->regulator); |
| if (err) |
| dev_warn(dsi->dev, "failed to enable VCC-DSI supply: %d\n", err); |
| |
| reset_control_deassert(dsi->reset); |
| clk_prepare_enable(dsi->mod_clk); |
| |
| /* |
| * Enable the DSI block. |
| */ |
| regmap_write(dsi->regs, SUN6I_DSI_CTL_REG, SUN6I_DSI_CTL_EN); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL0_REG, |
| SUN6I_DSI_BASIC_CTL0_ECC_EN | SUN6I_DSI_BASIC_CTL0_CRC_EN); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_TRANS_START_REG, 10); |
| regmap_write(dsi->regs, SUN6I_DSI_TRANS_ZERO_REG, 0); |
| |
| sun6i_dsi_inst_init(dsi, dsi->device); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_DEBUG_DATA_REG, 0xff); |
| |
| delay = sun6i_dsi_get_video_start_delay(dsi, mode); |
| regmap_write(dsi->regs, SUN6I_DSI_BASIC_CTL1_REG, |
| SUN6I_DSI_BASIC_CTL1_VIDEO_ST_DELAY(delay) | |
| SUN6I_DSI_BASIC_CTL1_VIDEO_FILL | |
| SUN6I_DSI_BASIC_CTL1_VIDEO_PRECISION | |
| SUN6I_DSI_BASIC_CTL1_VIDEO_MODE); |
| |
| sun6i_dsi_setup_burst(dsi, mode); |
| sun6i_dsi_setup_inst_loop(dsi, mode); |
| sun6i_dsi_setup_format(dsi, mode); |
| sun6i_dsi_setup_timings(dsi, mode); |
| |
| phy_init(dsi->dphy); |
| |
| phy_mipi_dphy_get_default_config(mode->clock * 1000, |
| mipi_dsi_pixel_format_to_bpp(device->format), |
| device->lanes, cfg); |
| |
| phy_set_mode(dsi->dphy, PHY_MODE_MIPI_DPHY); |
| phy_configure(dsi->dphy, &opts); |
| phy_power_on(dsi->dphy); |
| |
| if (dsi->panel) |
| drm_panel_prepare(dsi->panel); |
| |
| /* |
| * FIXME: This should be moved after the switch to HS mode. |
| * |
| * Unfortunately, once in HS mode, it seems like we're not |
| * able to send DCS commands anymore, which would prevent any |
| * panel to send any DCS command as part as their enable |
| * method, which is quite common. |
| * |
| * I haven't seen any artifact due to that sub-optimal |
| * ordering on the panels I've tested it with, so I guess this |
| * will do for now, until that IP is better understood. |
| */ |
| if (dsi->panel) |
| drm_panel_enable(dsi->panel); |
| |
| sun6i_dsi_start(dsi, DSI_START_HSC); |
| |
| udelay(1000); |
| |
| sun6i_dsi_start(dsi, DSI_START_HSD); |
| } |
| |
| static void sun6i_dsi_encoder_disable(struct drm_encoder *encoder) |
| { |
| struct sun6i_dsi *dsi = encoder_to_sun6i_dsi(encoder); |
| |
| DRM_DEBUG_DRIVER("Disabling DSI output\n"); |
| |
| if (dsi->panel) { |
| drm_panel_disable(dsi->panel); |
| drm_panel_unprepare(dsi->panel); |
| } |
| |
| phy_power_off(dsi->dphy); |
| phy_exit(dsi->dphy); |
| |
| clk_disable_unprepare(dsi->mod_clk); |
| reset_control_assert(dsi->reset); |
| regulator_disable(dsi->regulator); |
| } |
| |
| static int sun6i_dsi_get_modes(struct drm_connector *connector) |
| { |
| struct sun6i_dsi *dsi = connector_to_sun6i_dsi(connector); |
| |
| return drm_panel_get_modes(dsi->panel, connector); |
| } |
| |
| static const struct drm_connector_helper_funcs sun6i_dsi_connector_helper_funcs = { |
| .get_modes = sun6i_dsi_get_modes, |
| }; |
| |
| static enum drm_connector_status |
| sun6i_dsi_connector_detect(struct drm_connector *connector, bool force) |
| { |
| struct sun6i_dsi *dsi = connector_to_sun6i_dsi(connector); |
| |
| return dsi->panel ? connector_status_connected : |
| connector_status_disconnected; |
| } |
| |
| static const struct drm_connector_funcs sun6i_dsi_connector_funcs = { |
| .detect = sun6i_dsi_connector_detect, |
| .fill_modes = drm_helper_probe_single_connector_modes, |
| .destroy = drm_connector_cleanup, |
| .reset = drm_atomic_helper_connector_reset, |
| .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state, |
| .atomic_destroy_state = drm_atomic_helper_connector_destroy_state, |
| }; |
| |
| static const struct drm_encoder_helper_funcs sun6i_dsi_enc_helper_funcs = { |
| .disable = sun6i_dsi_encoder_disable, |
| .enable = sun6i_dsi_encoder_enable, |
| }; |
| |
| static u32 sun6i_dsi_dcs_build_pkt_hdr(struct sun6i_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| u32 pkt = msg->type; |
| |
| if (msg->type == MIPI_DSI_DCS_LONG_WRITE) { |
| pkt |= ((msg->tx_len) & 0xffff) << 8; |
| pkt |= (((msg->tx_len) >> 8) & 0xffff) << 16; |
| } else { |
| pkt |= (((u8 *)msg->tx_buf)[0] << 8); |
| if (msg->tx_len > 1) |
| pkt |= (((u8 *)msg->tx_buf)[1] << 16); |
| } |
| |
| pkt |= sun6i_dsi_ecc_compute(pkt) << 24; |
| |
| return pkt; |
| } |
| |
| static int sun6i_dsi_dcs_write_short(struct sun6i_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0), |
| sun6i_dsi_dcs_build_pkt_hdr(dsi, msg)); |
| regmap_write_bits(dsi->regs, SUN6I_DSI_CMD_CTL_REG, |
| 0xff, (4 - 1)); |
| |
| sun6i_dsi_start(dsi, DSI_START_LPTX); |
| |
| return msg->tx_len; |
| } |
| |
| static int sun6i_dsi_dcs_write_long(struct sun6i_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| int ret, len = 0; |
| u8 *bounce; |
| u16 crc; |
| |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0), |
| sun6i_dsi_dcs_build_pkt_hdr(dsi, msg)); |
| |
| bounce = kzalloc(ALIGN(msg->tx_len + sizeof(crc), 4), GFP_KERNEL); |
| if (!bounce) |
| return -ENOMEM; |
| |
| memcpy(bounce, msg->tx_buf, msg->tx_len); |
| len += msg->tx_len; |
| |
| crc = sun6i_dsi_crc_compute(bounce, msg->tx_len); |
| memcpy((u8 *)bounce + msg->tx_len, &crc, sizeof(crc)); |
| len += sizeof(crc); |
| |
| regmap_bulk_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(1), bounce, DIV_ROUND_UP(len, 4)); |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG, len + 4 - 1); |
| kfree(bounce); |
| |
| sun6i_dsi_start(dsi, DSI_START_LPTX); |
| |
| ret = sun6i_dsi_inst_wait_for_completion(dsi); |
| if (ret < 0) { |
| sun6i_dsi_inst_abort(dsi); |
| return ret; |
| } |
| |
| /* |
| * TODO: There's some bits (reg 0x200, bits 8/9) that |
| * apparently can be used to check whether the data have been |
| * sent, but I couldn't get it to work reliably. |
| */ |
| return msg->tx_len; |
| } |
| |
| static int sun6i_dsi_dcs_read(struct sun6i_dsi *dsi, |
| const struct mipi_dsi_msg *msg) |
| { |
| u32 val; |
| int ret; |
| u8 byte0; |
| |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_TX_REG(0), |
| sun6i_dsi_dcs_build_pkt_hdr(dsi, msg)); |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG, |
| (4 - 1)); |
| |
| sun6i_dsi_start(dsi, DSI_START_LPRX); |
| |
| ret = sun6i_dsi_inst_wait_for_completion(dsi); |
| if (ret < 0) { |
| sun6i_dsi_inst_abort(dsi); |
| return ret; |
| } |
| |
| /* |
| * TODO: There's some bits (reg 0x200, bits 24/25) that |
| * apparently can be used to check whether the data have been |
| * received, but I couldn't get it to work reliably. |
| */ |
| regmap_read(dsi->regs, SUN6I_DSI_CMD_CTL_REG, &val); |
| if (val & SUN6I_DSI_CMD_CTL_RX_OVERFLOW) |
| return -EIO; |
| |
| regmap_read(dsi->regs, SUN6I_DSI_CMD_RX_REG(0), &val); |
| byte0 = val & 0xff; |
| if (byte0 == MIPI_DSI_RX_ACKNOWLEDGE_AND_ERROR_REPORT) |
| return -EIO; |
| |
| ((u8 *)msg->rx_buf)[0] = (val >> 8); |
| |
| return 1; |
| } |
| |
| static int sun6i_dsi_attach(struct mipi_dsi_host *host, |
| struct mipi_dsi_device *device) |
| { |
| struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); |
| struct drm_panel *panel = of_drm_find_panel(device->dev.of_node); |
| |
| if (IS_ERR(panel)) |
| return PTR_ERR(panel); |
| if (!dsi->drm || !dsi->drm->registered) |
| return -EPROBE_DEFER; |
| |
| dsi->panel = panel; |
| dsi->device = device; |
| |
| drm_kms_helper_hotplug_event(dsi->drm); |
| |
| dev_info(host->dev, "Attached device %s\n", device->name); |
| |
| return 0; |
| } |
| |
| static int sun6i_dsi_detach(struct mipi_dsi_host *host, |
| struct mipi_dsi_device *device) |
| { |
| struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); |
| |
| dsi->panel = NULL; |
| dsi->device = NULL; |
| |
| drm_kms_helper_hotplug_event(dsi->drm); |
| |
| return 0; |
| } |
| |
| static ssize_t sun6i_dsi_transfer(struct mipi_dsi_host *host, |
| const struct mipi_dsi_msg *msg) |
| { |
| struct sun6i_dsi *dsi = host_to_sun6i_dsi(host); |
| int ret; |
| |
| ret = sun6i_dsi_inst_wait_for_completion(dsi); |
| if (ret < 0) |
| sun6i_dsi_inst_abort(dsi); |
| |
| regmap_write(dsi->regs, SUN6I_DSI_CMD_CTL_REG, |
| SUN6I_DSI_CMD_CTL_RX_OVERFLOW | |
| SUN6I_DSI_CMD_CTL_RX_FLAG | |
| SUN6I_DSI_CMD_CTL_TX_FLAG); |
| |
| switch (msg->type) { |
| case MIPI_DSI_DCS_SHORT_WRITE: |
| case MIPI_DSI_DCS_SHORT_WRITE_PARAM: |
| case MIPI_DSI_GENERIC_SHORT_WRITE_2_PARAM: |
| ret = sun6i_dsi_dcs_write_short(dsi, msg); |
| break; |
| |
| case MIPI_DSI_DCS_LONG_WRITE: |
| ret = sun6i_dsi_dcs_write_long(dsi, msg); |
| break; |
| |
| case MIPI_DSI_DCS_READ: |
| if (msg->rx_len == 1) { |
| ret = sun6i_dsi_dcs_read(dsi, msg); |
| break; |
| } |
| fallthrough; |
| |
| default: |
| ret = -EINVAL; |
| } |
| |
| return ret; |
| } |
| |
| static const struct mipi_dsi_host_ops sun6i_dsi_host_ops = { |
| .attach = sun6i_dsi_attach, |
| .detach = sun6i_dsi_detach, |
| .transfer = sun6i_dsi_transfer, |
| }; |
| |
| static const struct regmap_config sun6i_dsi_regmap_config = { |
| .reg_bits = 32, |
| .val_bits = 32, |
| .reg_stride = 4, |
| .max_register = SUN6I_DSI_CMD_TX_REG(255), |
| .name = "mipi-dsi", |
| }; |
| |
| static int sun6i_dsi_bind(struct device *dev, struct device *master, |
| void *data) |
| { |
| struct drm_device *drm = data; |
| struct sun6i_dsi *dsi = dev_get_drvdata(dev); |
| int ret; |
| |
| drm_encoder_helper_add(&dsi->encoder, |
| &sun6i_dsi_enc_helper_funcs); |
| ret = drm_simple_encoder_init(drm, &dsi->encoder, |
| DRM_MODE_ENCODER_DSI); |
| if (ret) { |
| dev_err(dsi->dev, "Couldn't initialise the DSI encoder\n"); |
| return ret; |
| } |
| dsi->encoder.possible_crtcs = BIT(0); |
| |
| drm_connector_helper_add(&dsi->connector, |
| &sun6i_dsi_connector_helper_funcs); |
| ret = drm_connector_init(drm, &dsi->connector, |
| &sun6i_dsi_connector_funcs, |
| DRM_MODE_CONNECTOR_DSI); |
| if (ret) { |
| dev_err(dsi->dev, |
| "Couldn't initialise the DSI connector\n"); |
| goto err_cleanup_connector; |
| } |
| |
| drm_connector_attach_encoder(&dsi->connector, &dsi->encoder); |
| |
| dsi->drm = drm; |
| |
| return 0; |
| |
| err_cleanup_connector: |
| drm_encoder_cleanup(&dsi->encoder); |
| return ret; |
| } |
| |
| static void sun6i_dsi_unbind(struct device *dev, struct device *master, |
| void *data) |
| { |
| struct sun6i_dsi *dsi = dev_get_drvdata(dev); |
| |
| dsi->drm = NULL; |
| } |
| |
| static const struct component_ops sun6i_dsi_ops = { |
| .bind = sun6i_dsi_bind, |
| .unbind = sun6i_dsi_unbind, |
| }; |
| |
| static int sun6i_dsi_probe(struct platform_device *pdev) |
| { |
| const struct sun6i_dsi_variant *variant; |
| struct device *dev = &pdev->dev; |
| struct sun6i_dsi *dsi; |
| void __iomem *base; |
| int ret; |
| |
| variant = device_get_match_data(dev); |
| if (!variant) |
| return -EINVAL; |
| |
| dsi = devm_kzalloc(dev, sizeof(*dsi), GFP_KERNEL); |
| if (!dsi) |
| return -ENOMEM; |
| dev_set_drvdata(dev, dsi); |
| dsi->dev = dev; |
| dsi->host.ops = &sun6i_dsi_host_ops; |
| dsi->host.dev = dev; |
| dsi->variant = variant; |
| |
| base = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(base)) { |
| dev_err(dev, "Couldn't map the DSI encoder registers\n"); |
| return PTR_ERR(base); |
| } |
| |
| dsi->regulator = devm_regulator_get(dev, "vcc-dsi"); |
| if (IS_ERR(dsi->regulator)) |
| return dev_err_probe(dev, PTR_ERR(dsi->regulator), |
| "Couldn't get VCC-DSI supply\n"); |
| |
| dsi->reset = devm_reset_control_get_shared(dev, NULL); |
| if (IS_ERR(dsi->reset)) { |
| dev_err(dev, "Couldn't get our reset line\n"); |
| return PTR_ERR(dsi->reset); |
| } |
| |
| dsi->regs = devm_regmap_init_mmio(dev, base, &sun6i_dsi_regmap_config); |
| if (IS_ERR(dsi->regs)) { |
| dev_err(dev, "Couldn't init regmap\n"); |
| return PTR_ERR(dsi->regs); |
| } |
| |
| dsi->bus_clk = devm_clk_get(dev, variant->has_mod_clk ? "bus" : NULL); |
| if (IS_ERR(dsi->bus_clk)) |
| return dev_err_probe(dev, PTR_ERR(dsi->bus_clk), |
| "Couldn't get the DSI bus clock\n"); |
| |
| ret = regmap_mmio_attach_clk(dsi->regs, dsi->bus_clk); |
| if (ret) |
| return ret; |
| |
| if (variant->has_mod_clk) { |
| dsi->mod_clk = devm_clk_get(dev, "mod"); |
| if (IS_ERR(dsi->mod_clk)) { |
| dev_err(dev, "Couldn't get the DSI mod clock\n"); |
| ret = PTR_ERR(dsi->mod_clk); |
| goto err_attach_clk; |
| } |
| |
| /* |
| * In order to operate properly, the module clock on the |
| * A31 variant always seems to be set to 297MHz. |
| */ |
| if (variant->set_mod_clk) |
| clk_set_rate_exclusive(dsi->mod_clk, 297000000); |
| } |
| |
| dsi->dphy = devm_phy_get(dev, "dphy"); |
| if (IS_ERR(dsi->dphy)) { |
| dev_err(dev, "Couldn't get the MIPI D-PHY\n"); |
| ret = PTR_ERR(dsi->dphy); |
| goto err_unprotect_clk; |
| } |
| |
| ret = mipi_dsi_host_register(&dsi->host); |
| if (ret) { |
| dev_err(dev, "Couldn't register MIPI-DSI host\n"); |
| goto err_unprotect_clk; |
| } |
| |
| ret = component_add(&pdev->dev, &sun6i_dsi_ops); |
| if (ret) { |
| dev_err(dev, "Couldn't register our component\n"); |
| goto err_remove_dsi_host; |
| } |
| |
| return 0; |
| |
| err_remove_dsi_host: |
| mipi_dsi_host_unregister(&dsi->host); |
| err_unprotect_clk: |
| if (dsi->variant->has_mod_clk && dsi->variant->set_mod_clk) |
| clk_rate_exclusive_put(dsi->mod_clk); |
| err_attach_clk: |
| regmap_mmio_detach_clk(dsi->regs); |
| |
| return ret; |
| } |
| |
| static void sun6i_dsi_remove(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct sun6i_dsi *dsi = dev_get_drvdata(dev); |
| |
| component_del(&pdev->dev, &sun6i_dsi_ops); |
| mipi_dsi_host_unregister(&dsi->host); |
| if (dsi->variant->has_mod_clk && dsi->variant->set_mod_clk) |
| clk_rate_exclusive_put(dsi->mod_clk); |
| |
| regmap_mmio_detach_clk(dsi->regs); |
| } |
| |
| static const struct sun6i_dsi_variant sun6i_a31_mipi_dsi_variant = { |
| .has_mod_clk = true, |
| .set_mod_clk = true, |
| }; |
| |
| static const struct sun6i_dsi_variant sun50i_a64_mipi_dsi_variant = { |
| }; |
| |
| static const struct sun6i_dsi_variant sun50i_a100_mipi_dsi_variant = { |
| .has_mod_clk = true, |
| }; |
| |
| static const struct of_device_id sun6i_dsi_of_table[] = { |
| { |
| .compatible = "allwinner,sun6i-a31-mipi-dsi", |
| .data = &sun6i_a31_mipi_dsi_variant, |
| }, |
| { |
| .compatible = "allwinner,sun50i-a64-mipi-dsi", |
| .data = &sun50i_a64_mipi_dsi_variant, |
| }, |
| { |
| .compatible = "allwinner,sun50i-a100-mipi-dsi", |
| .data = &sun50i_a100_mipi_dsi_variant, |
| }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, sun6i_dsi_of_table); |
| |
| static struct platform_driver sun6i_dsi_platform_driver = { |
| .probe = sun6i_dsi_probe, |
| .remove_new = sun6i_dsi_remove, |
| .driver = { |
| .name = "sun6i-mipi-dsi", |
| .of_match_table = sun6i_dsi_of_table, |
| }, |
| }; |
| module_platform_driver(sun6i_dsi_platform_driver); |
| |
| MODULE_AUTHOR("Maxime Ripard <maxime.ripard@free-electrons.com>"); |
| MODULE_DESCRIPTION("Allwinner A31 DSI Driver"); |
| MODULE_LICENSE("GPL"); |