| // SPDX-License-Identifier: GPL-2.0-or-later |
| // Copyright 2019 IBM Corp. |
| /dts-v1/; |
| |
| #include "aspeed-g6.dtsi" |
| #include <dt-bindings/gpio/aspeed-gpio.h> |
| #include <dt-bindings/i2c/i2c.h> |
| #include <dt-bindings/leds/leds-pca955x.h> |
| |
| / { |
| model = "Rainier 2U"; |
| compatible = "ibm,rainier-bmc", "aspeed,ast2600"; |
| |
| aliases { |
| serial4 = &uart5; |
| i2c16 = &i2c2mux0; |
| i2c17 = &i2c2mux1; |
| i2c18 = &i2c2mux2; |
| i2c19 = &i2c2mux3; |
| i2c20 = &i2c4mux0chn0; |
| i2c21 = &i2c4mux0chn1; |
| i2c22 = &i2c4mux0chn2; |
| i2c23 = &i2c5mux0chn0; |
| i2c24 = &i2c5mux0chn1; |
| i2c25 = &i2c6mux0chn0; |
| i2c26 = &i2c6mux0chn1; |
| i2c27 = &i2c6mux0chn2; |
| i2c28 = &i2c6mux0chn3; |
| i2c29 = &i2c11mux0chn0; |
| i2c30 = &i2c11mux0chn1; |
| }; |
| |
| chosen { |
| stdout-path = &uart5; |
| bootargs = "console=ttyS4,115200n8 earlycon"; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x40000000>; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| ramoops@b3e00000 { |
| compatible = "ramoops"; |
| reg = <0xb3e00000 0x200000>; /* 16 * (4 * 0x8000) */ |
| record-size = <0x8000>; |
| console-size = <0x8000>; |
| ftrace-size = <0x8000>; |
| pmsg-size = <0x8000>; |
| max-reason = <3>; /* KMSG_DUMP_EMERG */ |
| }; |
| |
| /* LPC FW cycle bridge region requires natural alignment */ |
| flash_memory: region@b4000000 { |
| no-map; |
| reg = <0xb4000000 0x04000000>; /* 64M */ |
| }; |
| |
| /* VGA region is dictated by hardware strapping */ |
| vga_memory: region@bf000000 { |
| no-map; |
| compatible = "shared-dma-pool"; |
| reg = <0xbf000000 0x01000000>; /* 16M */ |
| }; |
| }; |
| |
| i2c2mux: i2cmux { |
| compatible = "i2c-mux-gpio"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| |
| i2c-parent = <&i2c2>; |
| mux-gpios = <&gpio0 ASPEED_GPIO(G, 4) GPIO_ACTIVE_HIGH>, |
| <&gpio0 ASPEED_GPIO(G, 5) GPIO_ACTIVE_HIGH>; |
| idle-state = <0>; |
| |
| i2c2mux0: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| }; |
| |
| i2c2mux1: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| }; |
| |
| i2c2mux2: i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| }; |
| |
| i2c2mux3: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| /* BMC Card fault LED at the back */ |
| bmc-ingraham0 { |
| gpios = <&gpio0 ASPEED_GPIO(H, 1) GPIO_ACTIVE_LOW>; |
| }; |
| |
| /* Enclosure ID LED at the back */ |
| rear-enc-id0 { |
| gpios = <&gpio0 ASPEED_GPIO(H, 2) GPIO_ACTIVE_LOW>; |
| }; |
| |
| /* Enclosure fault LED at the back */ |
| rear-enc-fault0 { |
| gpios = <&gpio0 ASPEED_GPIO(H, 3) GPIO_ACTIVE_LOW>; |
| }; |
| |
| /* PCIE slot power LED */ |
| pcieslot-power { |
| gpios = <&gpio0 ASPEED_GPIO(P, 4) GPIO_ACTIVE_LOW>; |
| }; |
| }; |
| |
| gpio-keys-polled { |
| compatible = "gpio-keys-polled"; |
| poll-interval = <1000>; |
| |
| event-fan0-presence { |
| label = "fan0-presence"; |
| gpios = <&pca0 6 GPIO_ACTIVE_LOW>; |
| linux,code = <6>; |
| }; |
| |
| event-fan1-presence { |
| label = "fan1-presence"; |
| gpios = <&pca0 7 GPIO_ACTIVE_LOW>; |
| linux,code = <7>; |
| }; |
| |
| event-fan2-presence { |
| label = "fan2-presence"; |
| gpios = <&pca0 8 GPIO_ACTIVE_LOW>; |
| linux,code = <8>; |
| }; |
| |
| event-fan3-presence { |
| label = "fan3-presence"; |
| gpios = <&pca0 9 GPIO_ACTIVE_LOW>; |
| linux,code = <9>; |
| }; |
| |
| event-fan4-presence { |
| label = "fan4-presence"; |
| gpios = <&pca0 10 GPIO_ACTIVE_LOW>; |
| linux,code = <10>; |
| }; |
| |
| event-fan5-presence { |
| label = "fan5-presence"; |
| gpios = <&pca0 11 GPIO_ACTIVE_LOW>; |
| linux,code = <11>; |
| }; |
| }; |
| |
| iio-hwmon { |
| compatible = "iio-hwmon"; |
| io-channels = <&adc1 7>; |
| }; |
| }; |
| |
| &adc1 { |
| status = "okay"; |
| aspeed,int-vref-microvolt = <2500000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default |
| &pinctrl_adc10_default &pinctrl_adc11_default |
| &pinctrl_adc12_default &pinctrl_adc13_default |
| &pinctrl_adc14_default &pinctrl_adc15_default>; |
| }; |
| |
| &ehci1 { |
| status = "okay"; |
| }; |
| |
| &uhci { |
| status = "okay"; |
| }; |
| |
| &gpio0 { |
| gpio-line-names = |
| /*A0-A7*/ "","","","","","","","", |
| /*B0-B7*/ "","","","","","","checkstop","", |
| /*C0-C7*/ "","","","","","","","", |
| /*D0-D7*/ "","","","","","","","", |
| /*E0-E7*/ "","","","","","","","", |
| /*F0-F7*/ "","","rtc-battery-voltage-read-enable","reset-cause-pinhole","","","factory-reset-toggle","", |
| /*G0-G7*/ "","","","","","","","", |
| /*H0-H7*/ "","bmc-ingraham0","rear-enc-id0","rear-enc-fault0","","","","", |
| /*I0-I7*/ "","","","","","","bmc-secure-boot","", |
| /*J0-J7*/ "","","","","","","","", |
| /*K0-K7*/ "","","","","","","","", |
| /*L0-L7*/ "","","","","","","","", |
| /*M0-M7*/ "","","","","","","","", |
| /*N0-N7*/ "","","","","","","","", |
| /*O0-O7*/ "","","","usb-power","","","","", |
| /*P0-P7*/ "","","","","pcieslot-power","","","", |
| /*Q0-Q7*/ "cfam-reset","","regulator-standby-faulted","","","","","", |
| /*R0-R7*/ "bmc-tpm-reset","power-chassis-control","power-chassis-good","","","","","", |
| /*S0-S7*/ "presence-ps0","presence-ps1","presence-ps2","presence-ps3", |
| "power-ffs-sync-history","","","", |
| /*T0-T7*/ "","","","","","","","", |
| /*U0-U7*/ "","","","","","","","", |
| /*V0-V7*/ "","","","","","","","", |
| /*W0-W7*/ "","","","","","","","", |
| /*X0-X7*/ "","","","","","","","", |
| /*Y0-Y7*/ "","","","","","","","", |
| /*Z0-Z7*/ "","","","","","","",""; |
| |
| i2c3_mux_oe_n { |
| gpio-hog; |
| gpios = <ASPEED_GPIO(G, 6) GPIO_ACTIVE_LOW>; |
| output-high; |
| line-name = "I2C3_MUX_OE_N"; |
| }; |
| |
| usb_power { |
| gpio-hog; |
| gpios = <ASPEED_GPIO(O, 3) GPIO_ACTIVE_LOW>; |
| output-high; |
| }; |
| }; |
| |
| &emmc_controller { |
| status = "okay"; |
| }; |
| |
| &pinctrl_emmc_default { |
| bias-disable; |
| }; |
| |
| &emmc { |
| status = "okay"; |
| clk-phase-mmc-hs200 = <180>, <180>; |
| }; |
| |
| &ibt { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| |
| tca_pres1: tca9554@20{ |
| compatible = "ti,tca9554"; |
| reg = <0x20>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = "", |
| "RUSSEL_FW_I2C_ENABLE_N", |
| "RUSSEL_OPPANEL_PRESENCE_N", |
| "BLYTH_OPPANEL_PRESENCE_N", |
| "CPU_TPM_CARD_PRESENT_N", |
| "DASD_BP2_PRESENT_N", |
| "DASD_BP1_PRESENT_N", |
| "DASD_BP0_PRESENT_N"; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| }; |
| |
| &i2c2 { |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| status = "okay"; |
| |
| power-supply@68 { |
| compatible = "ibm,cffps"; |
| reg = <0x68>; |
| }; |
| |
| power-supply@69 { |
| compatible = "ibm,cffps"; |
| reg = <0x69>; |
| }; |
| |
| pca_pres1: pca9552@61 { |
| compatible = "nxp,pca9552"; |
| reg = <0x61>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLOT0_PRSNT_EN_RSVD", "SLOT1_PRSNT_EN_RSVD", |
| "SLOT2_PRSNT_EN_RSVD", "SLOT3_PRSNT_EN_RSVD", |
| "SLOT4_PRSNT_EN_RSVD", "SLOT0_EXPANDER_PRSNT_N", |
| "SLOT1_EXPANDER_PRSNT_N", "SLOT2_EXPANDER_PRSNT_N", |
| "SLOT3_EXPANDER_PRSNT_N", "SLOT4_EXPANDER_PRSNT_N", |
| "", "", "", "", "", ""; |
| }; |
| }; |
| |
| &i2c4 { |
| status = "okay"; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| tmp275@49 { |
| compatible = "ti,tmp275"; |
| reg = <0x49>; |
| }; |
| |
| tmp275@4a { |
| compatible = "ti,tmp275"; |
| reg = <0x4a>; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9546"; |
| reg = <0x70>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| i2c-mux-idle-disconnect; |
| |
| i2c4mux0chn0: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9551@60 { |
| compatible = "nxp,pca9551"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "cablecard0-cxp-top"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "cablecard0-cxp-bot"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| i2c4mux0chn1: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| }; |
| |
| i2c4mux0chn2: i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| |
| eeprom@52 { |
| compatible = "atmel,24c64"; |
| reg = <0x52>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c5 { |
| status = "okay"; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| tmp275@49 { |
| compatible = "ti,tmp275"; |
| reg = <0x49>; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9546"; |
| reg = <0x70>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| i2c-mux-idle-disconnect; |
| |
| i2c5mux0chn0: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9551@60 { |
| compatible = "nxp,pca9551"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "cablecard3-cxp-top"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "cablecard3-cxp-bot"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| i2c5mux0chn1: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| |
| pca9551@61 { |
| compatible = "nxp,pca9551"; |
| reg = <0x61>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "cablecard4-cxp-top"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "cablecard4-cxp-bot"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c6 { |
| status = "okay"; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| tmp275@4a { |
| compatible = "ti,tmp275"; |
| reg = <0x4a>; |
| }; |
| |
| tmp275@4b { |
| compatible = "ti,tmp275"; |
| reg = <0x4b>; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9546"; |
| reg = <0x70>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| i2c-mux-idle-disconnect; |
| |
| i2c6mux0chn0: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| eeprom@53 { |
| compatible = "atmel,24c64"; |
| reg = <0x53>; |
| }; |
| }; |
| |
| i2c6mux0chn1: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| |
| eeprom@52 { |
| compatible = "atmel,24c64"; |
| reg = <0x52>; |
| }; |
| }; |
| |
| i2c6mux0chn2: i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| }; |
| |
| i2c6mux0chn3: i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c7 { |
| multi-master; |
| status = "okay"; |
| |
| pca9552@30 { |
| compatible = "ibm,pca9552"; |
| reg = <0x30>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "pcieslot0"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "pcieslot1"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "pcieslot2"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "pcieslot3"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "pcieslot4"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "cpu1"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "cpu-vrm1"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@8 { |
| label = "lcd-russel"; |
| reg = <8>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| pca9552@31 { |
| compatible = "ibm,pca9552"; |
| reg = <0x31>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "ddimm0"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "ddimm1"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "ddimm2"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "ddimm3"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "ddimm4"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "ddimm5"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "ddimm6"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "ddimm7"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@8 { |
| label = "ddimm8"; |
| reg = <8>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@9 { |
| label = "ddimm9"; |
| reg = <9>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@10 { |
| label = "ddimm10"; |
| reg = <10>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@11 { |
| label = "ddimm11"; |
| reg = <11>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@12 { |
| label = "ddimm12"; |
| reg = <12>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@13 { |
| label = "ddimm13"; |
| reg = <13>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@14 { |
| label = "ddimm14"; |
| reg = <14>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@15 { |
| label = "ddimm15"; |
| reg = <15>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| pca9552@32 { |
| compatible = "ibm,pca9552"; |
| reg = <0x32>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "ddimm16"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "ddimm17"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "ddimm18"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "ddimm19"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "ddimm20"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "ddimm21"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "ddimm22"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "ddimm23"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@8 { |
| label = "ddimm24"; |
| reg = <8>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@9 { |
| label = "ddimm25"; |
| reg = <9>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@10 { |
| label = "ddimm26"; |
| reg = <10>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@11 { |
| label = "ddimm27"; |
| reg = <11>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@12 { |
| label = "ddimm28"; |
| reg = <12>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@13 { |
| label = "ddimm29"; |
| reg = <13>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@14 { |
| label = "ddimm30"; |
| reg = <14>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@15 { |
| label = "ddimm31"; |
| reg = <15>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| pca9552@33 { |
| compatible = "ibm,pca9552"; |
| reg = <0x33>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "planar"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "cpu0"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "dasd-pyramid0"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "dasd-pyramid1"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "dasd-pyramid2"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "cpu0-vrm0"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "rtc-battery"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@8 { |
| label = "base-blyth"; |
| reg = <8>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@9 { |
| label = "pcieslot6"; |
| reg = <9>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@10 { |
| label = "pcieslot7"; |
| reg = <10>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@11 { |
| label = "pcieslot8"; |
| reg = <11>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@12 { |
| label = "pcieslot9"; |
| reg = <12>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@13 { |
| label = "pcieslot10"; |
| reg = <13>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@14 { |
| label = "pcieslot11"; |
| reg = <14>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@15 { |
| label = "tpm-wilson"; |
| reg = <15>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| si7021-a20@40 { |
| compatible = "silabs,si7020"; |
| reg = <0x40>; |
| }; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| max: max31785@52 { |
| compatible = "maxim,max31785a"; |
| reg = <0x52>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| fan0: fan@0 { |
| compatible = "pmbus-fan"; |
| reg = <0>; |
| tach-pulses = <2>; |
| }; |
| |
| fan1: fan@1 { |
| compatible = "pmbus-fan"; |
| reg = <1>; |
| tach-pulses = <2>; |
| }; |
| |
| fan2: fan@2 { |
| compatible = "pmbus-fan"; |
| reg = <2>; |
| tach-pulses = <2>; |
| }; |
| |
| fan3: fan@3 { |
| compatible = "pmbus-fan"; |
| reg = <3>; |
| tach-pulses = <2>; |
| }; |
| |
| fan4: fan@4 { |
| compatible = "pmbus-fan"; |
| reg = <4>; |
| tach-pulses = <2>; |
| }; |
| |
| fan5: fan@5 { |
| compatible = "pmbus-fan"; |
| reg = <5>; |
| tach-pulses = <2>; |
| }; |
| }; |
| |
| pca9551@60 { |
| compatible = "nxp,pca9551"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "front-sys-id0"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "front-check-log0"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "front-enc-fault1"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "front-sys-pwron0"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| pca0: pca9552@61 { |
| compatible = "nxp,pca9552"; |
| reg = <0x61>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "fan0"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "fan1"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "fan2"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "fan3"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "fan4"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "fan5"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| |
| ibm-panel@62 { |
| compatible = "ibm,op-panel"; |
| reg = <(0x62 | I2C_OWN_SLAVE_ADDRESS)>; |
| }; |
| |
| dps: dps310@76 { |
| compatible = "infineon,dps310"; |
| reg = <0x76>; |
| #io-channel-cells = <0>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| }; |
| |
| &i2c8 { |
| status = "okay"; |
| |
| ucd90320@11 { |
| compatible = "ti,ucd90320"; |
| reg = <0x11>; |
| }; |
| |
| rtc@32 { |
| compatible = "epson,rx8900"; |
| reg = <0x32>; |
| }; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| tmp275@4a { |
| compatible = "ti,tmp275"; |
| reg = <0x4a>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| |
| pca_pres3: pca9552@60 { |
| compatible = "nxp,pca9552"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "", "", "", "", "", "", "", "", |
| "", "", "", "", "", "", "power-config-full-load", ""; |
| }; |
| |
| pca_pres2: pca9552@61 { |
| compatible = "nxp,pca9552"; |
| reg = <0x61>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| gpio-line-names = |
| "SLOT6_PRSNT_EN_RSVD", "SLOT7_PRSNT_EN_RSVD", |
| "SLOT8_PRSNT_EN_RSVD", "SLOT9_PRSNT_EN_RSVD", |
| "SLOT10_PRSNT_EN_RSVD", "SLOT11_PRSNT_EN_RSVD", |
| "SLOT6_EXPANDER_PRSNT_N", "SLOT7_EXPANDER_PRSNT_N", |
| "SLOT8_EXPANDER_PRSNT_N", "SLOT9_EXPANDER_PRSNT_N", |
| "SLOT10_EXPANDER_PRSNT_N", "SLOT11_EXPANDER_PRSNT_N", |
| "", "", "", ""; |
| }; |
| |
| }; |
| |
| &i2c9 { |
| status = "okay"; |
| |
| tmp423a@4c { |
| compatible = "ti,tmp423"; |
| reg = <0x4c>; |
| }; |
| |
| tmp423b@4d { |
| compatible = "ti,tmp423"; |
| reg = <0x4d>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c128"; |
| reg = <0x50>; |
| }; |
| }; |
| |
| &i2c10 { |
| status = "okay"; |
| |
| tmp423a@4c { |
| compatible = "ti,tmp423"; |
| reg = <0x4c>; |
| }; |
| |
| tmp423b@4d { |
| compatible = "ti,tmp423"; |
| reg = <0x4d>; |
| }; |
| |
| eeprom@50 { |
| compatible = "atmel,24c128"; |
| reg = <0x50>; |
| }; |
| }; |
| |
| &i2c11 { |
| status = "okay"; |
| |
| tmp275@48 { |
| compatible = "ti,tmp275"; |
| reg = <0x48>; |
| }; |
| |
| tmp275@49 { |
| compatible = "ti,tmp275"; |
| reg = <0x49>; |
| }; |
| |
| i2c-mux@70 { |
| compatible = "nxp,pca9546"; |
| reg = <0x70>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "okay"; |
| i2c-mux-idle-disconnect; |
| |
| i2c11mux0chn0: i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9551@60 { |
| compatible = "nxp,pca9551"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "cablecard10-cxp-top"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "cablecard10-cxp-bot"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| i2c11mux0chn1: i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| |
| eeprom@51 { |
| compatible = "atmel,24c64"; |
| reg = <0x51>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c12 { |
| status = "okay"; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| }; |
| |
| &i2c13 { |
| status = "okay"; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9552@60 { |
| compatible = "nxp,pca9552"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "nvme0"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "nvme1"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "nvme2"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "nvme3"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "nvme4"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "nvme5"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "nvme6"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "nvme7"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| &i2c14 { |
| status = "okay"; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9552@60 { |
| compatible = "nxp,pca9552"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "nvme8"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "nvme9"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "nvme10"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "nvme11"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "nvme12"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "nvme13"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "nvme14"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "nvme15"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| &i2c15 { |
| status = "okay"; |
| |
| eeprom@50 { |
| compatible = "atmel,24c64"; |
| reg = <0x50>; |
| }; |
| |
| pca9552@60 { |
| compatible = "nxp,pca9552"; |
| reg = <0x60>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| gpio-controller; |
| #gpio-cells = <2>; |
| |
| led@0 { |
| label = "nvme16"; |
| reg = <0>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@1 { |
| label = "nvme17"; |
| reg = <1>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@2 { |
| label = "nvme18"; |
| reg = <2>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@3 { |
| label = "nvme19"; |
| reg = <3>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@4 { |
| label = "nvme20"; |
| reg = <4>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@5 { |
| label = "nvme21"; |
| reg = <5>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@6 { |
| label = "nvme22"; |
| reg = <6>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| |
| led@7 { |
| label = "nvme23"; |
| reg = <7>; |
| retain-state-shutdown; |
| default-state = "keep"; |
| type = <PCA955X_TYPE_LED>; |
| }; |
| }; |
| }; |
| |
| &uart2 { |
| status = "okay"; |
| }; |
| |
| &vuart1 { |
| status = "okay"; |
| }; |
| |
| &vuart2 { |
| status = "okay"; |
| }; |
| |
| &lpc_ctrl { |
| status = "okay"; |
| memory-region = <&flash_memory>; |
| }; |
| |
| &mac2 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rmii3_default>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC3CLK>, |
| <&syscon ASPEED_CLK_MAC3RCLK>; |
| clock-names = "MACCLK", "RCLK"; |
| use-ncsi; |
| }; |
| |
| &mac3 { |
| status = "okay"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_rmii4_default>; |
| clocks = <&syscon ASPEED_CLK_GATE_MAC4CLK>, |
| <&syscon ASPEED_CLK_MAC4RCLK>; |
| clock-names = "MACCLK", "RCLK"; |
| use-ncsi; |
| }; |
| |
| &wdt1 { |
| aspeed,reset-type = "none"; |
| aspeed,external-signal; |
| aspeed,ext-push-pull; |
| aspeed,ext-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdtrst1_default>; |
| }; |
| |
| &wdt2 { |
| status = "okay"; |
| }; |
| |
| &xdma { |
| status = "okay"; |
| memory-region = <&vga_memory>; |
| }; |
| |
| &kcs2 { |
| status = "okay"; |
| aspeed,lpc-io-reg = <0xca8 0xcac>; |
| }; |
| |
| &kcs3 { |
| status = "okay"; |
| aspeed,lpc-io-reg = <0xca2>; |
| aspeed,lpc-interrupts = <11 IRQ_TYPE_LEVEL_LOW>; |
| }; |
| |
| #include "ibm-power10-quad.dtsi" |
