| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * GPIO Chip driver for Analog Devices |
| * ADP5588/ADP5587 I/O Expander and QWERTY Keypad Controller |
| * |
| * Copyright 2009-2010 Analog Devices Inc. |
| */ |
| |
| #include <linux/module.h> |
| #include <linux/kernel.h> |
| #include <linux/slab.h> |
| #include <linux/init.h> |
| #include <linux/i2c.h> |
| #include <linux/gpio/driver.h> |
| #include <linux/interrupt.h> |
| #include <linux/irq.h> |
| #include <linux/of_device.h> |
| |
| #include <linux/platform_data/adp5588.h> |
| |
| #define DRV_NAME "adp5588-gpio" |
| |
| /* |
| * Early pre 4.0 Silicon required to delay readout by at least 25ms, |
| * since the Event Counter Register updated 25ms after the interrupt |
| * asserted. |
| */ |
| #define WA_DELAYED_READOUT_REVID(rev) ((rev) < 4) |
| |
| struct adp5588_gpio { |
| struct i2c_client *client; |
| struct gpio_chip gpio_chip; |
| struct mutex lock; /* protect cached dir, dat_out */ |
| /* protect serialized access to the interrupt controller bus */ |
| struct mutex irq_lock; |
| uint8_t dat_out[3]; |
| uint8_t dir[3]; |
| uint8_t int_lvl_low[3]; |
| uint8_t int_lvl_high[3]; |
| uint8_t int_en[3]; |
| uint8_t irq_mask[3]; |
| uint8_t int_input_en[3]; |
| }; |
| |
| static int adp5588_gpio_read(struct i2c_client *client, u8 reg) |
| { |
| int ret = i2c_smbus_read_byte_data(client, reg); |
| |
| if (ret < 0) |
| dev_err(&client->dev, "Read Error\n"); |
| |
| return ret; |
| } |
| |
| static int adp5588_gpio_write(struct i2c_client *client, u8 reg, u8 val) |
| { |
| int ret = i2c_smbus_write_byte_data(client, reg, val); |
| |
| if (ret < 0) |
| dev_err(&client->dev, "Write Error\n"); |
| |
| return ret; |
| } |
| |
| static int adp5588_gpio_get_value(struct gpio_chip *chip, unsigned off) |
| { |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); |
| unsigned bank = ADP5588_BANK(off); |
| unsigned bit = ADP5588_BIT(off); |
| int val; |
| |
| mutex_lock(&dev->lock); |
| |
| if (dev->dir[bank] & bit) |
| val = dev->dat_out[bank]; |
| else |
| val = adp5588_gpio_read(dev->client, GPIO_DAT_STAT1 + bank); |
| |
| mutex_unlock(&dev->lock); |
| |
| return !!(val & bit); |
| } |
| |
| static void adp5588_gpio_set_value(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| unsigned bank, bit; |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); |
| |
| bank = ADP5588_BANK(off); |
| bit = ADP5588_BIT(off); |
| |
| mutex_lock(&dev->lock); |
| if (val) |
| dev->dat_out[bank] |= bit; |
| else |
| dev->dat_out[bank] &= ~bit; |
| |
| adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, |
| dev->dat_out[bank]); |
| mutex_unlock(&dev->lock); |
| } |
| |
| static int adp5588_gpio_direction_input(struct gpio_chip *chip, unsigned off) |
| { |
| int ret; |
| unsigned bank; |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); |
| |
| bank = ADP5588_BANK(off); |
| |
| mutex_lock(&dev->lock); |
| dev->dir[bank] &= ~ADP5588_BIT(off); |
| ret = adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, dev->dir[bank]); |
| mutex_unlock(&dev->lock); |
| |
| return ret; |
| } |
| |
| static int adp5588_gpio_direction_output(struct gpio_chip *chip, |
| unsigned off, int val) |
| { |
| int ret; |
| unsigned bank, bit; |
| struct adp5588_gpio *dev = gpiochip_get_data(chip); |
| |
| bank = ADP5588_BANK(off); |
| bit = ADP5588_BIT(off); |
| |
| mutex_lock(&dev->lock); |
| dev->dir[bank] |= bit; |
| |
| if (val) |
| dev->dat_out[bank] |= bit; |
| else |
| dev->dat_out[bank] &= ~bit; |
| |
| ret = adp5588_gpio_write(dev->client, GPIO_DAT_OUT1 + bank, |
| dev->dat_out[bank]); |
| ret |= adp5588_gpio_write(dev->client, GPIO_DIR1 + bank, |
| dev->dir[bank]); |
| mutex_unlock(&dev->lock); |
| |
| return ret; |
| } |
| |
| #ifdef CONFIG_GPIO_ADP5588_IRQ |
| |
| static void adp5588_irq_bus_lock(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| |
| mutex_lock(&dev->irq_lock); |
| } |
| |
| /* |
| * genirq core code can issue chip->mask/unmask from atomic context. |
| * This doesn't work for slow busses where an access needs to sleep. |
| * bus_sync_unlock() is therefore called outside the atomic context, |
| * syncs the current irq mask state with the slow external controller |
| * and unlocks the bus. |
| */ |
| |
| static void adp5588_irq_bus_sync_unlock(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| int i; |
| |
| for (i = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { |
| if (dev->int_input_en[i]) { |
| mutex_lock(&dev->lock); |
| dev->dir[i] &= ~dev->int_input_en[i]; |
| dev->int_input_en[i] = 0; |
| adp5588_gpio_write(dev->client, GPIO_DIR1 + i, |
| dev->dir[i]); |
| mutex_unlock(&dev->lock); |
| } |
| |
| if (dev->int_en[i] ^ dev->irq_mask[i]) { |
| dev->int_en[i] = dev->irq_mask[i]; |
| adp5588_gpio_write(dev->client, GPI_EM1 + i, |
| dev->int_en[i]); |
| } |
| } |
| |
| mutex_unlock(&dev->irq_lock); |
| } |
| |
| static void adp5588_irq_mask(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| |
| dev->irq_mask[ADP5588_BANK(d->hwirq)] &= ~ADP5588_BIT(d->hwirq); |
| } |
| |
| static void adp5588_irq_unmask(struct irq_data *d) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| |
| dev->irq_mask[ADP5588_BANK(d->hwirq)] |= ADP5588_BIT(d->hwirq); |
| } |
| |
| static int adp5588_irq_set_type(struct irq_data *d, unsigned int type) |
| { |
| struct gpio_chip *gc = irq_data_get_irq_chip_data(d); |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| uint16_t gpio = d->hwirq; |
| unsigned bank, bit; |
| |
| bank = ADP5588_BANK(gpio); |
| bit = ADP5588_BIT(gpio); |
| |
| dev->int_lvl_low[bank] &= ~bit; |
| dev->int_lvl_high[bank] &= ~bit; |
| |
| if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_HIGH) |
| dev->int_lvl_high[bank] |= bit; |
| |
| if (type & IRQ_TYPE_EDGE_BOTH || type & IRQ_TYPE_LEVEL_LOW) |
| dev->int_lvl_low[bank] |= bit; |
| |
| dev->int_input_en[bank] |= bit; |
| |
| return 0; |
| } |
| |
| static struct irq_chip adp5588_irq_chip = { |
| .name = "adp5588", |
| .irq_mask = adp5588_irq_mask, |
| .irq_unmask = adp5588_irq_unmask, |
| .irq_bus_lock = adp5588_irq_bus_lock, |
| .irq_bus_sync_unlock = adp5588_irq_bus_sync_unlock, |
| .irq_set_type = adp5588_irq_set_type, |
| }; |
| |
| static irqreturn_t adp5588_irq_handler(int irq, void *devid) |
| { |
| struct adp5588_gpio *dev = devid; |
| int status = adp5588_gpio_read(dev->client, INT_STAT); |
| |
| if (status & ADP5588_KE_INT) { |
| int ev_cnt = adp5588_gpio_read(dev->client, KEY_LCK_EC_STAT); |
| |
| if (ev_cnt > 0) { |
| int i; |
| |
| for (i = 0; i < (ev_cnt & ADP5588_KEC); i++) { |
| int key = adp5588_gpio_read(dev->client, |
| Key_EVENTA + i); |
| /* GPIN events begin at 97, |
| * bit 7 indicates logic level |
| */ |
| int gpio = (key & 0x7f) - 97; |
| int lvl = key & (1 << 7); |
| int bank = ADP5588_BANK(gpio); |
| int bit = ADP5588_BIT(gpio); |
| |
| if ((lvl && dev->int_lvl_high[bank] & bit) || |
| (!lvl && dev->int_lvl_low[bank] & bit)) |
| handle_nested_irq(irq_find_mapping( |
| dev->gpio_chip.irq.domain, gpio)); |
| } |
| } |
| } |
| |
| adp5588_gpio_write(dev->client, INT_STAT, status); /* Status is W1C */ |
| |
| return IRQ_HANDLED; |
| } |
| |
| |
| static int adp5588_irq_init_hw(struct gpio_chip *gc) |
| { |
| struct adp5588_gpio *dev = gpiochip_get_data(gc); |
| /* Enable IRQs after registering chip */ |
| adp5588_gpio_write(dev->client, CFG, |
| ADP5588_AUTO_INC | ADP5588_INT_CFG | ADP5588_KE_IEN); |
| |
| return 0; |
| } |
| |
| static int adp5588_irq_setup(struct adp5588_gpio *dev) |
| { |
| struct i2c_client *client = dev->client; |
| int ret; |
| struct adp5588_gpio_platform_data *pdata = |
| dev_get_platdata(&client->dev); |
| struct gpio_irq_chip *girq; |
| |
| adp5588_gpio_write(client, CFG, ADP5588_AUTO_INC); |
| adp5588_gpio_write(client, INT_STAT, -1); /* status is W1C */ |
| |
| mutex_init(&dev->irq_lock); |
| |
| ret = devm_request_threaded_irq(&client->dev, client->irq, |
| NULL, adp5588_irq_handler, IRQF_ONESHOT |
| | IRQF_TRIGGER_FALLING | IRQF_SHARED, |
| dev_name(&client->dev), dev); |
| if (ret) { |
| dev_err(&client->dev, "failed to request irq %d\n", |
| client->irq); |
| return ret; |
| } |
| |
| /* This will be registered in the call to devm_gpiochip_add_data() */ |
| girq = &dev->gpio_chip.irq; |
| girq->chip = &adp5588_irq_chip; |
| /* This will let us handle the parent IRQ in the driver */ |
| girq->parent_handler = NULL; |
| girq->num_parents = 0; |
| girq->parents = NULL; |
| girq->first = pdata ? pdata->irq_base : 0; |
| girq->default_type = IRQ_TYPE_NONE; |
| girq->handler = handle_simple_irq; |
| girq->init_hw = adp5588_irq_init_hw; |
| girq->threaded = true; |
| |
| return 0; |
| } |
| |
| #else |
| static int adp5588_irq_setup(struct adp5588_gpio *dev) |
| { |
| struct i2c_client *client = dev->client; |
| dev_warn(&client->dev, "interrupt support not compiled in\n"); |
| |
| return 0; |
| } |
| |
| #endif /* CONFIG_GPIO_ADP5588_IRQ */ |
| |
| static int adp5588_gpio_probe(struct i2c_client *client) |
| { |
| struct adp5588_gpio_platform_data *pdata = |
| dev_get_platdata(&client->dev); |
| struct adp5588_gpio *dev; |
| struct gpio_chip *gc; |
| int ret, i, revid; |
| unsigned int pullup_dis_mask = 0; |
| |
| if (!i2c_check_functionality(client->adapter, |
| I2C_FUNC_SMBUS_BYTE_DATA)) { |
| dev_err(&client->dev, "SMBUS Byte Data not Supported\n"); |
| return -EIO; |
| } |
| |
| dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL); |
| if (!dev) |
| return -ENOMEM; |
| |
| dev->client = client; |
| |
| gc = &dev->gpio_chip; |
| gc->direction_input = adp5588_gpio_direction_input; |
| gc->direction_output = adp5588_gpio_direction_output; |
| gc->get = adp5588_gpio_get_value; |
| gc->set = adp5588_gpio_set_value; |
| gc->can_sleep = true; |
| gc->base = -1; |
| gc->parent = &client->dev; |
| |
| if (pdata) { |
| gc->base = pdata->gpio_start; |
| gc->names = pdata->names; |
| pullup_dis_mask = pdata->pullup_dis_mask; |
| } |
| |
| gc->ngpio = ADP5588_MAXGPIO; |
| gc->label = client->name; |
| gc->owner = THIS_MODULE; |
| |
| mutex_init(&dev->lock); |
| |
| ret = adp5588_gpio_read(dev->client, DEV_ID); |
| if (ret < 0) |
| return ret; |
| |
| revid = ret & ADP5588_DEVICE_ID_MASK; |
| |
| for (i = 0, ret = 0; i <= ADP5588_BANK(ADP5588_MAXGPIO); i++) { |
| dev->dat_out[i] = adp5588_gpio_read(client, GPIO_DAT_OUT1 + i); |
| dev->dir[i] = adp5588_gpio_read(client, GPIO_DIR1 + i); |
| ret |= adp5588_gpio_write(client, KP_GPIO1 + i, 0); |
| ret |= adp5588_gpio_write(client, GPIO_PULL1 + i, |
| (pullup_dis_mask >> (8 * i)) & 0xFF); |
| ret |= adp5588_gpio_write(client, GPIO_INT_EN1 + i, 0); |
| if (ret) |
| return ret; |
| } |
| |
| if (client->irq) { |
| if (WA_DELAYED_READOUT_REVID(revid)) { |
| dev_warn(&client->dev, "GPIO int not supported\n"); |
| } else { |
| ret = adp5588_irq_setup(dev); |
| if (ret) |
| return ret; |
| } |
| } |
| |
| ret = devm_gpiochip_add_data(&client->dev, &dev->gpio_chip, dev); |
| if (ret) |
| return ret; |
| |
| i2c_set_clientdata(client, dev); |
| |
| return 0; |
| } |
| |
| static int adp5588_gpio_remove(struct i2c_client *client) |
| { |
| struct adp5588_gpio *dev = i2c_get_clientdata(client); |
| |
| if (dev->client->irq) |
| free_irq(dev->client->irq, dev); |
| |
| return 0; |
| } |
| |
| static const struct i2c_device_id adp5588_gpio_id[] = { |
| {DRV_NAME, 0}, |
| {} |
| }; |
| MODULE_DEVICE_TABLE(i2c, adp5588_gpio_id); |
| |
| #ifdef CONFIG_OF |
| static const struct of_device_id adp5588_gpio_of_id[] = { |
| { .compatible = "adi," DRV_NAME, }, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, adp5588_gpio_of_id); |
| #endif |
| |
| static struct i2c_driver adp5588_gpio_driver = { |
| .driver = { |
| .name = DRV_NAME, |
| .of_match_table = of_match_ptr(adp5588_gpio_of_id), |
| }, |
| .probe_new = adp5588_gpio_probe, |
| .remove = adp5588_gpio_remove, |
| .id_table = adp5588_gpio_id, |
| }; |
| |
| module_i2c_driver(adp5588_gpio_driver); |
| |
| MODULE_AUTHOR("Michael Hennerich <michael.hennerich@analog.com>"); |
| MODULE_DESCRIPTION("GPIO ADP5588 Driver"); |
| MODULE_LICENSE("GPL"); |