| config STMMAC_ETH |
| tristate "STMicroelectronics 10/100/1000/EQOS Ethernet driver" |
| depends on HAS_IOMEM && HAS_DMA |
| select MII |
| select PHYLIB |
| select CRC32 |
| imply PTP_1588_CLOCK |
| select RESET_CONTROLLER |
| ---help--- |
| This is the driver for the Ethernet IPs built around a |
| Synopsys IP Core. |
| |
| if STMMAC_ETH |
| |
| config STMMAC_PLATFORM |
| tristate "STMMAC Platform bus support" |
| depends on STMMAC_ETH |
| select MFD_SYSCON |
| default y |
| ---help--- |
| This selects the platform specific bus support for the stmmac driver. |
| This is the driver used on several SoCs: |
| STi, Allwinner, Amlogic Meson, Altera SOCFPGA. |
| |
| If you have a controller with this interface, say Y or M here. |
| |
| If unsure, say N. |
| |
| if STMMAC_PLATFORM |
| |
| config DWMAC_DWC_QOS_ETH |
| tristate "Support for snps,dwc-qos-ethernet.txt DT binding." |
| select PHYLIB |
| select CRC32 |
| select MII |
| depends on OF && HAS_DMA |
| help |
| Support for chips using the snps,dwc-qos-ethernet.txt DT binding. |
| |
| config DWMAC_GENERIC |
| tristate "Generic driver for DWMAC" |
| default STMMAC_PLATFORM |
| ---help--- |
| Generic DWMAC driver for platforms that don't require any |
| platform specific code to function or is using platform |
| data for setup. |
| |
| config DWMAC_ANARION |
| tristate "Adaptrum Anarion GMAC support" |
| default ARC |
| depends on OF && (ARC || COMPILE_TEST) |
| help |
| Support for Adaptrum Anarion GMAC Ethernet controller. |
| |
| This selects the Anarion SoC glue layer support for the stmmac driver. |
| |
| config DWMAC_IPQ806X |
| tristate "QCA IPQ806x DWMAC support" |
| default ARCH_QCOM |
| depends on OF && (ARCH_QCOM || COMPILE_TEST) |
| select MFD_SYSCON |
| help |
| Support for QCA IPQ806X DWMAC Ethernet. |
| |
| This selects the IPQ806x SoC glue layer support for the stmmac |
| device driver. This driver does not use any of the hardware |
| acceleration features available on this SoC. Network devices |
| will behave like standard non-accelerated ethernet interfaces. |
| |
| config DWMAC_LPC18XX |
| tristate "NXP LPC18xx/43xx DWMAC support" |
| default ARCH_LPC18XX |
| depends on OF && (ARCH_LPC18XX || COMPILE_TEST) |
| select MFD_SYSCON |
| ---help--- |
| Support for NXP LPC18xx/43xx DWMAC Ethernet. |
| |
| config DWMAC_MESON |
| tristate "Amlogic Meson dwmac support" |
| default ARCH_MESON |
| depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST) |
| help |
| Support for Ethernet controller on Amlogic Meson SoCs. |
| |
| This selects the Amlogic Meson SoC glue layer support for |
| the stmmac device driver. This driver is used for Meson6, |
| Meson8, Meson8b and GXBB SoCs. |
| |
| config DWMAC_OXNAS |
| tristate "Oxford Semiconductor OXNAS dwmac support" |
| default ARCH_OXNAS |
| depends on OF && COMMON_CLK && (ARCH_OXNAS || COMPILE_TEST) |
| select MFD_SYSCON |
| help |
| Support for Ethernet controller on Oxford Semiconductor OXNAS SoCs. |
| |
| This selects the Oxford Semiconductor OXNASSoC glue layer support for |
| the stmmac device driver. This driver is used for OX820. |
| |
| config DWMAC_ROCKCHIP |
| tristate "Rockchip dwmac support" |
| default ARCH_ROCKCHIP |
| depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST) |
| select MFD_SYSCON |
| help |
| Support for Ethernet controller on Rockchip RK3288 SoC. |
| |
| This selects the Rockchip RK3288 SoC glue layer support for |
| the stmmac device driver. |
| |
| config DWMAC_SOCFPGA |
| tristate "SOCFPGA dwmac support" |
| default ARCH_SOCFPGA |
| depends on OF && (ARCH_SOCFPGA || ARCH_STRATIX10 || COMPILE_TEST) |
| select MFD_SYSCON |
| help |
| Support for ethernet controller on Altera SOCFPGA |
| |
| This selects the Altera SOCFPGA SoC glue layer support |
| for the stmmac device driver. This driver is used for |
| arria5 and cyclone5 FPGA SoCs. |
| |
| config DWMAC_STI |
| tristate "STi GMAC support" |
| default ARCH_STI |
| depends on OF && (ARCH_STI || COMPILE_TEST) |
| select MFD_SYSCON |
| ---help--- |
| Support for ethernet controller on STi SOCs. |
| |
| This selects STi SoC glue layer support for the stmmac |
| device driver. This driver is used on for the STi series |
| SOCs GMAC ethernet controller. |
| |
| config DWMAC_STM32 |
| tristate "STM32 DWMAC support" |
| default ARCH_STM32 |
| depends on OF && HAS_IOMEM && (ARCH_STM32 || COMPILE_TEST) |
| select MFD_SYSCON |
| ---help--- |
| Support for ethernet controller on STM32 SOCs. |
| |
| This selects STM32 SoC glue layer support for the stmmac |
| device driver. This driver is used on for the STM32 series |
| SOCs GMAC ethernet controller. |
| |
| config DWMAC_SUNXI |
| tristate "Allwinner GMAC support" |
| default ARCH_SUNXI |
| depends on OF && (ARCH_SUNXI || COMPILE_TEST) |
| ---help--- |
| Support for Allwinner A20/A31 GMAC ethernet controllers. |
| |
| This selects Allwinner SoC glue layer support for the |
| stmmac device driver. This driver is used for A20/A31 |
| GMAC ethernet controller. |
| |
| config DWMAC_SUN8I |
| tristate "Allwinner sun8i GMAC support" |
| default ARCH_SUNXI |
| depends on OF && (ARCH_SUNXI || COMPILE_TEST) |
| select MDIO_BUS_MUX |
| ---help--- |
| Support for Allwinner H3 A83T A64 EMAC ethernet controllers. |
| |
| This selects Allwinner SoC glue layer support for the |
| stmmac device driver. This driver is used for H3/A83T/A64 |
| EMAC ethernet controller. |
| endif |
| |
| config STMMAC_PCI |
| tristate "STMMAC PCI bus support" |
| depends on STMMAC_ETH && PCI |
| ---help--- |
| This selects the platform specific bus support for the stmmac driver. |
| This driver was tested on XLINX XC2V3000 FF1152AMT0221 |
| D1215994A VIRTEX FPGA board and SNPS QoS IPK Prototyping Kit. |
| |
| If you have a controller with this interface, say Y or M here. |
| |
| If unsure, say N. |
| endif |
