| /* bnx2x_ethtool.c: QLogic Everest network driver. |
| * |
| * Copyright (c) 2007-2013 Broadcom Corporation |
| * Copyright (c) 2014 QLogic Corporation |
| * All rights reserved |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License as published by |
| * the Free Software Foundation. |
| * |
| * Maintained by: Ariel Elior <ariel.elior@qlogic.com> |
| * Written by: Eliezer Tamir |
| * Based on code from Michael Chan's bnx2 driver |
| * UDP CSUM errata workaround by Arik Gendelman |
| * Slowpath and fastpath rework by Vladislav Zolotarov |
| * Statistics and Link management by Yitchak Gertner |
| * |
| */ |
| |
| #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt |
| |
| #include <linux/ethtool.h> |
| #include <linux/netdevice.h> |
| #include <linux/types.h> |
| #include <linux/sched.h> |
| #include <linux/crc32.h> |
| #include "bnx2x.h" |
| #include "bnx2x_cmn.h" |
| #include "bnx2x_dump.h" |
| #include "bnx2x_init.h" |
| |
| /* Note: in the format strings below %s is replaced by the queue-name which is |
| * either its index or 'fcoe' for the fcoe queue. Make sure the format string |
| * length does not exceed ETH_GSTRING_LEN - MAX_QUEUE_NAME_LEN + 2 |
| */ |
| #define MAX_QUEUE_NAME_LEN 4 |
| static const struct { |
| long offset; |
| int size; |
| char string[ETH_GSTRING_LEN]; |
| } bnx2x_q_stats_arr[] = { |
| /* 1 */ { Q_STATS_OFFSET32(total_bytes_received_hi), 8, "[%s]: rx_bytes" }, |
| { Q_STATS_OFFSET32(total_unicast_packets_received_hi), |
| 8, "[%s]: rx_ucast_packets" }, |
| { Q_STATS_OFFSET32(total_multicast_packets_received_hi), |
| 8, "[%s]: rx_mcast_packets" }, |
| { Q_STATS_OFFSET32(total_broadcast_packets_received_hi), |
| 8, "[%s]: rx_bcast_packets" }, |
| { Q_STATS_OFFSET32(no_buff_discard_hi), 8, "[%s]: rx_discards" }, |
| { Q_STATS_OFFSET32(rx_err_discard_pkt), |
| 4, "[%s]: rx_phy_ip_err_discards"}, |
| { Q_STATS_OFFSET32(rx_skb_alloc_failed), |
| 4, "[%s]: rx_skb_alloc_discard" }, |
| { Q_STATS_OFFSET32(hw_csum_err), 4, "[%s]: rx_csum_offload_errors" }, |
| { Q_STATS_OFFSET32(driver_xoff), 4, "[%s]: tx_exhaustion_events" }, |
| { Q_STATS_OFFSET32(total_bytes_transmitted_hi), 8, "[%s]: tx_bytes" }, |
| /* 10 */{ Q_STATS_OFFSET32(total_unicast_packets_transmitted_hi), |
| 8, "[%s]: tx_ucast_packets" }, |
| { Q_STATS_OFFSET32(total_multicast_packets_transmitted_hi), |
| 8, "[%s]: tx_mcast_packets" }, |
| { Q_STATS_OFFSET32(total_broadcast_packets_transmitted_hi), |
| 8, "[%s]: tx_bcast_packets" }, |
| { Q_STATS_OFFSET32(total_tpa_aggregations_hi), |
| 8, "[%s]: tpa_aggregations" }, |
| { Q_STATS_OFFSET32(total_tpa_aggregated_frames_hi), |
| 8, "[%s]: tpa_aggregated_frames"}, |
| { Q_STATS_OFFSET32(total_tpa_bytes_hi), 8, "[%s]: tpa_bytes"}, |
| { Q_STATS_OFFSET32(driver_filtered_tx_pkt), |
| 4, "[%s]: driver_filtered_tx_pkt" } |
| }; |
| |
| #define BNX2X_NUM_Q_STATS ARRAY_SIZE(bnx2x_q_stats_arr) |
| |
| static const struct { |
| long offset; |
| int size; |
| bool is_port_stat; |
| char string[ETH_GSTRING_LEN]; |
| } bnx2x_stats_arr[] = { |
| /* 1 */ { STATS_OFFSET32(total_bytes_received_hi), |
| 8, false, "rx_bytes" }, |
| { STATS_OFFSET32(error_bytes_received_hi), |
| 8, false, "rx_error_bytes" }, |
| { STATS_OFFSET32(total_unicast_packets_received_hi), |
| 8, false, "rx_ucast_packets" }, |
| { STATS_OFFSET32(total_multicast_packets_received_hi), |
| 8, false, "rx_mcast_packets" }, |
| { STATS_OFFSET32(total_broadcast_packets_received_hi), |
| 8, false, "rx_bcast_packets" }, |
| { STATS_OFFSET32(rx_stat_dot3statsfcserrors_hi), |
| 8, true, "rx_crc_errors" }, |
| { STATS_OFFSET32(rx_stat_dot3statsalignmenterrors_hi), |
| 8, true, "rx_align_errors" }, |
| { STATS_OFFSET32(rx_stat_etherstatsundersizepkts_hi), |
| 8, true, "rx_undersize_packets" }, |
| { STATS_OFFSET32(etherstatsoverrsizepkts_hi), |
| 8, true, "rx_oversize_packets" }, |
| /* 10 */{ STATS_OFFSET32(rx_stat_etherstatsfragments_hi), |
| 8, true, "rx_fragments" }, |
| { STATS_OFFSET32(rx_stat_etherstatsjabbers_hi), |
| 8, true, "rx_jabbers" }, |
| { STATS_OFFSET32(no_buff_discard_hi), |
| 8, false, "rx_discards" }, |
| { STATS_OFFSET32(mac_filter_discard), |
| 4, true, "rx_filtered_packets" }, |
| { STATS_OFFSET32(mf_tag_discard), |
| 4, true, "rx_mf_tag_discard" }, |
| { STATS_OFFSET32(pfc_frames_received_hi), |
| 8, true, "pfc_frames_received" }, |
| { STATS_OFFSET32(pfc_frames_sent_hi), |
| 8, true, "pfc_frames_sent" }, |
| { STATS_OFFSET32(brb_drop_hi), |
| 8, true, "rx_brb_discard" }, |
| { STATS_OFFSET32(brb_truncate_hi), |
| 8, true, "rx_brb_truncate" }, |
| { STATS_OFFSET32(pause_frames_received_hi), |
| 8, true, "rx_pause_frames" }, |
| { STATS_OFFSET32(rx_stat_maccontrolframesreceived_hi), |
| 8, true, "rx_mac_ctrl_frames" }, |
| { STATS_OFFSET32(nig_timer_max), |
| 4, true, "rx_constant_pause_events" }, |
| /* 20 */{ STATS_OFFSET32(rx_err_discard_pkt), |
| 4, false, "rx_phy_ip_err_discards"}, |
| { STATS_OFFSET32(rx_skb_alloc_failed), |
| 4, false, "rx_skb_alloc_discard" }, |
| { STATS_OFFSET32(hw_csum_err), |
| 4, false, "rx_csum_offload_errors" }, |
| { STATS_OFFSET32(driver_xoff), |
| 4, false, "tx_exhaustion_events" }, |
| { STATS_OFFSET32(total_bytes_transmitted_hi), |
| 8, false, "tx_bytes" }, |
| { STATS_OFFSET32(tx_stat_ifhcoutbadoctets_hi), |
| 8, true, "tx_error_bytes" }, |
| { STATS_OFFSET32(total_unicast_packets_transmitted_hi), |
| 8, false, "tx_ucast_packets" }, |
| { STATS_OFFSET32(total_multicast_packets_transmitted_hi), |
| 8, false, "tx_mcast_packets" }, |
| { STATS_OFFSET32(total_broadcast_packets_transmitted_hi), |
| 8, false, "tx_bcast_packets" }, |
| { STATS_OFFSET32(tx_stat_dot3statsinternalmactransmiterrors_hi), |
| 8, true, "tx_mac_errors" }, |
| { STATS_OFFSET32(rx_stat_dot3statscarriersenseerrors_hi), |
| 8, true, "tx_carrier_errors" }, |
| /* 30 */{ STATS_OFFSET32(tx_stat_dot3statssinglecollisionframes_hi), |
| 8, true, "tx_single_collisions" }, |
| { STATS_OFFSET32(tx_stat_dot3statsmultiplecollisionframes_hi), |
| 8, true, "tx_multi_collisions" }, |
| { STATS_OFFSET32(tx_stat_dot3statsdeferredtransmissions_hi), |
| 8, true, "tx_deferred" }, |
| { STATS_OFFSET32(tx_stat_dot3statsexcessivecollisions_hi), |
| 8, true, "tx_excess_collisions" }, |
| { STATS_OFFSET32(tx_stat_dot3statslatecollisions_hi), |
| 8, true, "tx_late_collisions" }, |
| { STATS_OFFSET32(tx_stat_etherstatscollisions_hi), |
| 8, true, "tx_total_collisions" }, |
| { STATS_OFFSET32(tx_stat_etherstatspkts64octets_hi), |
| 8, true, "tx_64_byte_packets" }, |
| { STATS_OFFSET32(tx_stat_etherstatspkts65octetsto127octets_hi), |
| 8, true, "tx_65_to_127_byte_packets" }, |
| { STATS_OFFSET32(tx_stat_etherstatspkts128octetsto255octets_hi), |
| 8, true, "tx_128_to_255_byte_packets" }, |
| { STATS_OFFSET32(tx_stat_etherstatspkts256octetsto511octets_hi), |
| 8, true, "tx_256_to_511_byte_packets" }, |
| /* 40 */{ STATS_OFFSET32(tx_stat_etherstatspkts512octetsto1023octets_hi), |
| 8, true, "tx_512_to_1023_byte_packets" }, |
| { STATS_OFFSET32(etherstatspkts1024octetsto1522octets_hi), |
| 8, true, "tx_1024_to_1522_byte_packets" }, |
| { STATS_OFFSET32(etherstatspktsover1522octets_hi), |
| 8, true, "tx_1523_to_9022_byte_packets" }, |
| { STATS_OFFSET32(pause_frames_sent_hi), |
| 8, true, "tx_pause_frames" }, |
| { STATS_OFFSET32(total_tpa_aggregations_hi), |
| 8, false, "tpa_aggregations" }, |
| { STATS_OFFSET32(total_tpa_aggregated_frames_hi), |
| 8, false, "tpa_aggregated_frames"}, |
| { STATS_OFFSET32(total_tpa_bytes_hi), |
| 8, false, "tpa_bytes"}, |
| { STATS_OFFSET32(recoverable_error), |
| 4, false, "recoverable_errors" }, |
| { STATS_OFFSET32(unrecoverable_error), |
| 4, false, "unrecoverable_errors" }, |
| { STATS_OFFSET32(driver_filtered_tx_pkt), |
| 4, false, "driver_filtered_tx_pkt" }, |
| { STATS_OFFSET32(eee_tx_lpi), |
| 4, true, "Tx LPI entry count"} |
| }; |
| |
| #define BNX2X_NUM_STATS ARRAY_SIZE(bnx2x_stats_arr) |
| |
| static int bnx2x_get_port_type(struct bnx2x *bp) |
| { |
| int port_type; |
| u32 phy_idx = bnx2x_get_cur_phy_idx(bp); |
| switch (bp->link_params.phy[phy_idx].media_type) { |
| case ETH_PHY_SFPP_10G_FIBER: |
| case ETH_PHY_SFP_1G_FIBER: |
| case ETH_PHY_XFP_FIBER: |
| case ETH_PHY_KR: |
| case ETH_PHY_CX4: |
| port_type = PORT_FIBRE; |
| break; |
| case ETH_PHY_DA_TWINAX: |
| port_type = PORT_DA; |
| break; |
| case ETH_PHY_BASE_T: |
| port_type = PORT_TP; |
| break; |
| case ETH_PHY_NOT_PRESENT: |
| port_type = PORT_NONE; |
| break; |
| case ETH_PHY_UNSPECIFIED: |
| default: |
| port_type = PORT_OTHER; |
| break; |
| } |
| return port_type; |
| } |
| |
| static int bnx2x_get_vf_link_ksettings(struct net_device *dev, |
| struct ethtool_link_ksettings *cmd) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 supported, advertising; |
| |
| ethtool_convert_link_mode_to_legacy_u32(&supported, |
| cmd->link_modes.supported); |
| ethtool_convert_link_mode_to_legacy_u32(&advertising, |
| cmd->link_modes.advertising); |
| |
| if (bp->state == BNX2X_STATE_OPEN) { |
| if (test_bit(BNX2X_LINK_REPORT_FD, |
| &bp->vf_link_vars.link_report_flags)) |
| cmd->base.duplex = DUPLEX_FULL; |
| else |
| cmd->base.duplex = DUPLEX_HALF; |
| |
| cmd->base.speed = bp->vf_link_vars.line_speed; |
| } else { |
| cmd->base.duplex = DUPLEX_UNKNOWN; |
| cmd->base.speed = SPEED_UNKNOWN; |
| } |
| |
| cmd->base.port = PORT_OTHER; |
| cmd->base.phy_address = 0; |
| cmd->base.autoneg = AUTONEG_DISABLE; |
| |
| DP(BNX2X_MSG_ETHTOOL, "ethtool_cmd: cmd %d\n" |
| " supported 0x%x advertising 0x%x speed %u\n" |
| " duplex %d port %d phy_address %d\n" |
| " autoneg %d\n", |
| cmd->base.cmd, supported, advertising, |
| cmd->base.speed, |
| cmd->base.duplex, cmd->base.port, cmd->base.phy_address, |
| cmd->base.autoneg); |
| |
| return 0; |
| } |
| |
| static int bnx2x_get_link_ksettings(struct net_device *dev, |
| struct ethtool_link_ksettings *cmd) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| u32 media_type; |
| u32 supported, advertising, lp_advertising; |
| |
| ethtool_convert_link_mode_to_legacy_u32(&lp_advertising, |
| cmd->link_modes.lp_advertising); |
| |
| /* Dual Media boards present all available port types */ |
| supported = bp->port.supported[cfg_idx] | |
| (bp->port.supported[cfg_idx ^ 1] & |
| (SUPPORTED_TP | SUPPORTED_FIBRE)); |
| advertising = bp->port.advertising[cfg_idx]; |
| media_type = bp->link_params.phy[bnx2x_get_cur_phy_idx(bp)].media_type; |
| if (media_type == ETH_PHY_SFP_1G_FIBER) { |
| supported &= ~(SUPPORTED_10000baseT_Full); |
| advertising &= ~(ADVERTISED_10000baseT_Full); |
| } |
| |
| if ((bp->state == BNX2X_STATE_OPEN) && bp->link_vars.link_up && |
| !(bp->flags & MF_FUNC_DIS)) { |
| cmd->base.duplex = bp->link_vars.duplex; |
| |
| if (IS_MF(bp) && !BP_NOMCP(bp)) |
| cmd->base.speed = bnx2x_get_mf_speed(bp); |
| else |
| cmd->base.speed = bp->link_vars.line_speed; |
| } else { |
| cmd->base.duplex = DUPLEX_UNKNOWN; |
| cmd->base.speed = SPEED_UNKNOWN; |
| } |
| |
| cmd->base.port = bnx2x_get_port_type(bp); |
| |
| cmd->base.phy_address = bp->mdio.prtad; |
| |
| if (bp->link_params.req_line_speed[cfg_idx] == SPEED_AUTO_NEG) |
| cmd->base.autoneg = AUTONEG_ENABLE; |
| else |
| cmd->base.autoneg = AUTONEG_DISABLE; |
| |
| /* Publish LP advertised speeds and FC */ |
| if (bp->link_vars.link_status & LINK_STATUS_AUTO_NEGOTIATE_COMPLETE) { |
| u32 status = bp->link_vars.link_status; |
| |
| lp_advertising |= ADVERTISED_Autoneg; |
| if (status & LINK_STATUS_LINK_PARTNER_SYMMETRIC_PAUSE) |
| lp_advertising |= ADVERTISED_Pause; |
| if (status & LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE) |
| lp_advertising |= ADVERTISED_Asym_Pause; |
| |
| if (status & LINK_STATUS_LINK_PARTNER_10THD_CAPABLE) |
| lp_advertising |= ADVERTISED_10baseT_Half; |
| if (status & LINK_STATUS_LINK_PARTNER_10TFD_CAPABLE) |
| lp_advertising |= ADVERTISED_10baseT_Full; |
| if (status & LINK_STATUS_LINK_PARTNER_100TXHD_CAPABLE) |
| lp_advertising |= ADVERTISED_100baseT_Half; |
| if (status & LINK_STATUS_LINK_PARTNER_100TXFD_CAPABLE) |
| lp_advertising |= ADVERTISED_100baseT_Full; |
| if (status & LINK_STATUS_LINK_PARTNER_1000THD_CAPABLE) |
| lp_advertising |= ADVERTISED_1000baseT_Half; |
| if (status & LINK_STATUS_LINK_PARTNER_1000TFD_CAPABLE) { |
| if (media_type == ETH_PHY_KR) { |
| lp_advertising |= |
| ADVERTISED_1000baseKX_Full; |
| } else { |
| lp_advertising |= |
| ADVERTISED_1000baseT_Full; |
| } |
| } |
| if (status & LINK_STATUS_LINK_PARTNER_2500XFD_CAPABLE) |
| lp_advertising |= ADVERTISED_2500baseX_Full; |
| if (status & LINK_STATUS_LINK_PARTNER_10GXFD_CAPABLE) { |
| if (media_type == ETH_PHY_KR) { |
| lp_advertising |= |
| ADVERTISED_10000baseKR_Full; |
| } else { |
| lp_advertising |= |
| ADVERTISED_10000baseT_Full; |
| } |
| } |
| if (status & LINK_STATUS_LINK_PARTNER_20GXFD_CAPABLE) |
| lp_advertising |= ADVERTISED_20000baseKR2_Full; |
| } |
| |
| ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.supported, |
| supported); |
| ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.advertising, |
| advertising); |
| ethtool_convert_legacy_u32_to_link_mode(cmd->link_modes.lp_advertising, |
| lp_advertising); |
| |
| DP(BNX2X_MSG_ETHTOOL, "ethtool_cmd: cmd %d\n" |
| " supported 0x%x advertising 0x%x speed %u\n" |
| " duplex %d port %d phy_address %d\n" |
| " autoneg %d\n", |
| cmd->base.cmd, supported, advertising, |
| cmd->base.speed, |
| cmd->base.duplex, cmd->base.port, cmd->base.phy_address, |
| cmd->base.autoneg); |
| |
| return 0; |
| } |
| |
| static int bnx2x_set_link_ksettings(struct net_device *dev, |
| const struct ethtool_link_ksettings *cmd) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 advertising, cfg_idx, old_multi_phy_config, new_multi_phy_config; |
| u32 speed, phy_idx; |
| u32 supported; |
| u8 duplex = cmd->base.duplex; |
| |
| ethtool_convert_link_mode_to_legacy_u32(&supported, |
| cmd->link_modes.supported); |
| ethtool_convert_link_mode_to_legacy_u32(&advertising, |
| cmd->link_modes.advertising); |
| |
| if (IS_MF_SD(bp)) |
| return 0; |
| |
| DP(BNX2X_MSG_ETHTOOL, "ethtool_cmd: cmd %d\n" |
| " supported 0x%x advertising 0x%x speed %u\n" |
| " duplex %d port %d phy_address %d\n" |
| " autoneg %d\n", |
| cmd->base.cmd, supported, advertising, |
| cmd->base.speed, |
| cmd->base.duplex, cmd->base.port, cmd->base.phy_address, |
| cmd->base.autoneg); |
| |
| speed = cmd->base.speed; |
| |
| /* If received a request for an unknown duplex, assume full*/ |
| if (duplex == DUPLEX_UNKNOWN) |
| duplex = DUPLEX_FULL; |
| |
| if (IS_MF_SI(bp)) { |
| u32 part; |
| u32 line_speed = bp->link_vars.line_speed; |
| |
| /* use 10G if no link detected */ |
| if (!line_speed) |
| line_speed = 10000; |
| |
| if (bp->common.bc_ver < REQ_BC_VER_4_SET_MF_BW) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "To set speed BC %X or higher is required, please upgrade BC\n", |
| REQ_BC_VER_4_SET_MF_BW); |
| return -EINVAL; |
| } |
| |
| part = (speed * 100) / line_speed; |
| |
| if (line_speed < speed || !part) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Speed setting should be in a range from 1%% to 100%% of actual line speed\n"); |
| return -EINVAL; |
| } |
| |
| if (bp->state != BNX2X_STATE_OPEN) |
| /* store value for following "load" */ |
| bp->pending_max = part; |
| else |
| bnx2x_update_max_mf_config(bp, part); |
| |
| return 0; |
| } |
| |
| cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| old_multi_phy_config = bp->link_params.multi_phy_config; |
| if (cmd->base.port != bnx2x_get_port_type(bp)) { |
| switch (cmd->base.port) { |
| case PORT_TP: |
| if (!(bp->port.supported[0] & SUPPORTED_TP || |
| bp->port.supported[1] & SUPPORTED_TP)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Unsupported port type\n"); |
| return -EINVAL; |
| } |
| bp->link_params.multi_phy_config &= |
| ~PORT_HW_CFG_PHY_SELECTION_MASK; |
| if (bp->link_params.multi_phy_config & |
| PORT_HW_CFG_PHY_SWAPPED_ENABLED) |
| bp->link_params.multi_phy_config |= |
| PORT_HW_CFG_PHY_SELECTION_SECOND_PHY; |
| else |
| bp->link_params.multi_phy_config |= |
| PORT_HW_CFG_PHY_SELECTION_FIRST_PHY; |
| break; |
| case PORT_FIBRE: |
| case PORT_DA: |
| case PORT_NONE: |
| if (!(bp->port.supported[0] & SUPPORTED_FIBRE || |
| bp->port.supported[1] & SUPPORTED_FIBRE)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Unsupported port type\n"); |
| return -EINVAL; |
| } |
| bp->link_params.multi_phy_config &= |
| ~PORT_HW_CFG_PHY_SELECTION_MASK; |
| if (bp->link_params.multi_phy_config & |
| PORT_HW_CFG_PHY_SWAPPED_ENABLED) |
| bp->link_params.multi_phy_config |= |
| PORT_HW_CFG_PHY_SELECTION_FIRST_PHY; |
| else |
| bp->link_params.multi_phy_config |= |
| PORT_HW_CFG_PHY_SELECTION_SECOND_PHY; |
| break; |
| default: |
| DP(BNX2X_MSG_ETHTOOL, "Unsupported port type\n"); |
| return -EINVAL; |
| } |
| } |
| /* Save new config in case command complete successfully */ |
| new_multi_phy_config = bp->link_params.multi_phy_config; |
| /* Get the new cfg_idx */ |
| cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| /* Restore old config in case command failed */ |
| bp->link_params.multi_phy_config = old_multi_phy_config; |
| DP(BNX2X_MSG_ETHTOOL, "cfg_idx = %x\n", cfg_idx); |
| |
| if (cmd->base.autoneg == AUTONEG_ENABLE) { |
| u32 an_supported_speed = bp->port.supported[cfg_idx]; |
| if (bp->link_params.phy[EXT_PHY1].type == |
| PORT_HW_CFG_XGXS_EXT_PHY_TYPE_BCM84833) |
| an_supported_speed |= (SUPPORTED_100baseT_Half | |
| SUPPORTED_100baseT_Full); |
| if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) { |
| DP(BNX2X_MSG_ETHTOOL, "Autoneg not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* advertise the requested speed and duplex if supported */ |
| if (advertising & ~an_supported_speed) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Advertisement parameters are not supported\n"); |
| return -EINVAL; |
| } |
| |
| bp->link_params.req_line_speed[cfg_idx] = SPEED_AUTO_NEG; |
| bp->link_params.req_duplex[cfg_idx] = duplex; |
| bp->port.advertising[cfg_idx] = (ADVERTISED_Autoneg | |
| advertising); |
| if (advertising) { |
| |
| bp->link_params.speed_cap_mask[cfg_idx] = 0; |
| if (advertising & ADVERTISED_10baseT_Half) { |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_HALF; |
| } |
| if (advertising & ADVERTISED_10baseT_Full) |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10M_FULL; |
| |
| if (advertising & ADVERTISED_100baseT_Full) |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_FULL; |
| |
| if (advertising & ADVERTISED_100baseT_Half) { |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_100M_HALF; |
| } |
| if (advertising & ADVERTISED_1000baseT_Half) { |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_1G; |
| } |
| if (advertising & (ADVERTISED_1000baseT_Full | |
| ADVERTISED_1000baseKX_Full)) |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_1G; |
| |
| if (advertising & (ADVERTISED_10000baseT_Full | |
| ADVERTISED_10000baseKX4_Full | |
| ADVERTISED_10000baseKR_Full)) |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_10G; |
| |
| if (advertising & ADVERTISED_20000baseKR2_Full) |
| bp->link_params.speed_cap_mask[cfg_idx] |= |
| PORT_HW_CFG_SPEED_CAPABILITY_D0_20G; |
| } |
| } else { /* forced speed */ |
| /* advertise the requested speed and duplex if supported */ |
| switch (speed) { |
| case SPEED_10: |
| if (duplex == DUPLEX_FULL) { |
| if (!(bp->port.supported[cfg_idx] & |
| SUPPORTED_10baseT_Full)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "10M full not supported\n"); |
| return -EINVAL; |
| } |
| |
| advertising = (ADVERTISED_10baseT_Full | |
| ADVERTISED_TP); |
| } else { |
| if (!(bp->port.supported[cfg_idx] & |
| SUPPORTED_10baseT_Half)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "10M half not supported\n"); |
| return -EINVAL; |
| } |
| |
| advertising = (ADVERTISED_10baseT_Half | |
| ADVERTISED_TP); |
| } |
| break; |
| |
| case SPEED_100: |
| if (duplex == DUPLEX_FULL) { |
| if (!(bp->port.supported[cfg_idx] & |
| SUPPORTED_100baseT_Full)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "100M full not supported\n"); |
| return -EINVAL; |
| } |
| |
| advertising = (ADVERTISED_100baseT_Full | |
| ADVERTISED_TP); |
| } else { |
| if (!(bp->port.supported[cfg_idx] & |
| SUPPORTED_100baseT_Half)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "100M half not supported\n"); |
| return -EINVAL; |
| } |
| |
| advertising = (ADVERTISED_100baseT_Half | |
| ADVERTISED_TP); |
| } |
| break; |
| |
| case SPEED_1000: |
| if (duplex != DUPLEX_FULL) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "1G half not supported\n"); |
| return -EINVAL; |
| } |
| |
| if (bp->port.supported[cfg_idx] & |
| SUPPORTED_1000baseT_Full) { |
| advertising = (ADVERTISED_1000baseT_Full | |
| ADVERTISED_TP); |
| |
| } else if (bp->port.supported[cfg_idx] & |
| SUPPORTED_1000baseKX_Full) { |
| advertising = ADVERTISED_1000baseKX_Full; |
| } else { |
| DP(BNX2X_MSG_ETHTOOL, |
| "1G full not supported\n"); |
| return -EINVAL; |
| } |
| |
| break; |
| |
| case SPEED_2500: |
| if (duplex != DUPLEX_FULL) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "2.5G half not supported\n"); |
| return -EINVAL; |
| } |
| |
| if (!(bp->port.supported[cfg_idx] |
| & SUPPORTED_2500baseX_Full)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "2.5G full not supported\n"); |
| return -EINVAL; |
| } |
| |
| advertising = (ADVERTISED_2500baseX_Full | |
| ADVERTISED_TP); |
| break; |
| |
| case SPEED_10000: |
| if (duplex != DUPLEX_FULL) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "10G half not supported\n"); |
| return -EINVAL; |
| } |
| phy_idx = bnx2x_get_cur_phy_idx(bp); |
| if ((bp->port.supported[cfg_idx] & |
| SUPPORTED_10000baseT_Full) && |
| (bp->link_params.phy[phy_idx].media_type != |
| ETH_PHY_SFP_1G_FIBER)) { |
| advertising = (ADVERTISED_10000baseT_Full | |
| ADVERTISED_FIBRE); |
| } else if (bp->port.supported[cfg_idx] & |
| SUPPORTED_10000baseKR_Full) { |
| advertising = (ADVERTISED_10000baseKR_Full | |
| ADVERTISED_FIBRE); |
| } else { |
| DP(BNX2X_MSG_ETHTOOL, |
| "10G full not supported\n"); |
| return -EINVAL; |
| } |
| |
| break; |
| |
| default: |
| DP(BNX2X_MSG_ETHTOOL, "Unsupported speed %u\n", speed); |
| return -EINVAL; |
| } |
| |
| bp->link_params.req_line_speed[cfg_idx] = speed; |
| bp->link_params.req_duplex[cfg_idx] = duplex; |
| bp->port.advertising[cfg_idx] = advertising; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL, "req_line_speed %d\n" |
| " req_duplex %d advertising 0x%x\n", |
| bp->link_params.req_line_speed[cfg_idx], |
| bp->link_params.req_duplex[cfg_idx], |
| bp->port.advertising[cfg_idx]); |
| |
| /* Set new config */ |
| bp->link_params.multi_phy_config = new_multi_phy_config; |
| if (netif_running(dev)) { |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| bnx2x_force_link_reset(bp); |
| bnx2x_link_set(bp); |
| } |
| |
| return 0; |
| } |
| |
| #define DUMP_ALL_PRESETS 0x1FFF |
| #define DUMP_MAX_PRESETS 13 |
| |
| static int __bnx2x_get_preset_regs_len(struct bnx2x *bp, u32 preset) |
| { |
| if (CHIP_IS_E1(bp)) |
| return dump_num_registers[0][preset-1]; |
| else if (CHIP_IS_E1H(bp)) |
| return dump_num_registers[1][preset-1]; |
| else if (CHIP_IS_E2(bp)) |
| return dump_num_registers[2][preset-1]; |
| else if (CHIP_IS_E3A0(bp)) |
| return dump_num_registers[3][preset-1]; |
| else if (CHIP_IS_E3B0(bp)) |
| return dump_num_registers[4][preset-1]; |
| else |
| return 0; |
| } |
| |
| static int __bnx2x_get_regs_len(struct bnx2x *bp) |
| { |
| u32 preset_idx; |
| int regdump_len = 0; |
| |
| /* Calculate the total preset regs length */ |
| for (preset_idx = 1; preset_idx <= DUMP_MAX_PRESETS; preset_idx++) |
| regdump_len += __bnx2x_get_preset_regs_len(bp, preset_idx); |
| |
| return regdump_len; |
| } |
| |
| static int bnx2x_get_regs_len(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int regdump_len = 0; |
| |
| if (IS_VF(bp)) |
| return 0; |
| |
| regdump_len = __bnx2x_get_regs_len(bp); |
| regdump_len *= 4; |
| regdump_len += sizeof(struct dump_header); |
| |
| return regdump_len; |
| } |
| |
| #define IS_E1_REG(chips) ((chips & DUMP_CHIP_E1) == DUMP_CHIP_E1) |
| #define IS_E1H_REG(chips) ((chips & DUMP_CHIP_E1H) == DUMP_CHIP_E1H) |
| #define IS_E2_REG(chips) ((chips & DUMP_CHIP_E2) == DUMP_CHIP_E2) |
| #define IS_E3A0_REG(chips) ((chips & DUMP_CHIP_E3A0) == DUMP_CHIP_E3A0) |
| #define IS_E3B0_REG(chips) ((chips & DUMP_CHIP_E3B0) == DUMP_CHIP_E3B0) |
| |
| #define IS_REG_IN_PRESET(presets, idx) \ |
| ((presets & (1 << (idx-1))) == (1 << (idx-1))) |
| |
| /******* Paged registers info selectors ********/ |
| static const u32 *__bnx2x_get_page_addr_ar(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return page_vals_e2; |
| else if (CHIP_IS_E3(bp)) |
| return page_vals_e3; |
| else |
| return NULL; |
| } |
| |
| static u32 __bnx2x_get_page_reg_num(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return PAGE_MODE_VALUES_E2; |
| else if (CHIP_IS_E3(bp)) |
| return PAGE_MODE_VALUES_E3; |
| else |
| return 0; |
| } |
| |
| static const u32 *__bnx2x_get_page_write_ar(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return page_write_regs_e2; |
| else if (CHIP_IS_E3(bp)) |
| return page_write_regs_e3; |
| else |
| return NULL; |
| } |
| |
| static u32 __bnx2x_get_page_write_num(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return PAGE_WRITE_REGS_E2; |
| else if (CHIP_IS_E3(bp)) |
| return PAGE_WRITE_REGS_E3; |
| else |
| return 0; |
| } |
| |
| static const struct reg_addr *__bnx2x_get_page_read_ar(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return page_read_regs_e2; |
| else if (CHIP_IS_E3(bp)) |
| return page_read_regs_e3; |
| else |
| return NULL; |
| } |
| |
| static u32 __bnx2x_get_page_read_num(struct bnx2x *bp) |
| { |
| if (CHIP_IS_E2(bp)) |
| return PAGE_READ_REGS_E2; |
| else if (CHIP_IS_E3(bp)) |
| return PAGE_READ_REGS_E3; |
| else |
| return 0; |
| } |
| |
| static bool bnx2x_is_reg_in_chip(struct bnx2x *bp, |
| const struct reg_addr *reg_info) |
| { |
| if (CHIP_IS_E1(bp)) |
| return IS_E1_REG(reg_info->chips); |
| else if (CHIP_IS_E1H(bp)) |
| return IS_E1H_REG(reg_info->chips); |
| else if (CHIP_IS_E2(bp)) |
| return IS_E2_REG(reg_info->chips); |
| else if (CHIP_IS_E3A0(bp)) |
| return IS_E3A0_REG(reg_info->chips); |
| else if (CHIP_IS_E3B0(bp)) |
| return IS_E3B0_REG(reg_info->chips); |
| else |
| return false; |
| } |
| |
| static bool bnx2x_is_wreg_in_chip(struct bnx2x *bp, |
| const struct wreg_addr *wreg_info) |
| { |
| if (CHIP_IS_E1(bp)) |
| return IS_E1_REG(wreg_info->chips); |
| else if (CHIP_IS_E1H(bp)) |
| return IS_E1H_REG(wreg_info->chips); |
| else if (CHIP_IS_E2(bp)) |
| return IS_E2_REG(wreg_info->chips); |
| else if (CHIP_IS_E3A0(bp)) |
| return IS_E3A0_REG(wreg_info->chips); |
| else if (CHIP_IS_E3B0(bp)) |
| return IS_E3B0_REG(wreg_info->chips); |
| else |
| return false; |
| } |
| |
| /** |
| * bnx2x_read_pages_regs - read "paged" registers |
| * |
| * @bp device handle |
| * @p output buffer |
| * |
| * Reads "paged" memories: memories that may only be read by first writing to a |
| * specific address ("write address") and then reading from a specific address |
| * ("read address"). There may be more than one write address per "page" and |
| * more than one read address per write address. |
| */ |
| static void bnx2x_read_pages_regs(struct bnx2x *bp, u32 *p, u32 preset) |
| { |
| u32 i, j, k, n; |
| |
| /* addresses of the paged registers */ |
| const u32 *page_addr = __bnx2x_get_page_addr_ar(bp); |
| /* number of paged registers */ |
| int num_pages = __bnx2x_get_page_reg_num(bp); |
| /* write addresses */ |
| const u32 *write_addr = __bnx2x_get_page_write_ar(bp); |
| /* number of write addresses */ |
| int write_num = __bnx2x_get_page_write_num(bp); |
| /* read addresses info */ |
| const struct reg_addr *read_addr = __bnx2x_get_page_read_ar(bp); |
| /* number of read addresses */ |
| int read_num = __bnx2x_get_page_read_num(bp); |
| u32 addr, size; |
| |
| for (i = 0; i < num_pages; i++) { |
| for (j = 0; j < write_num; j++) { |
| REG_WR(bp, write_addr[j], page_addr[i]); |
| |
| for (k = 0; k < read_num; k++) { |
| if (IS_REG_IN_PRESET(read_addr[k].presets, |
| preset)) { |
| size = read_addr[k].size; |
| for (n = 0; n < size; n++) { |
| addr = read_addr[k].addr + n*4; |
| *p++ = REG_RD(bp, addr); |
| } |
| } |
| } |
| } |
| } |
| } |
| |
| static int __bnx2x_get_preset_regs(struct bnx2x *bp, u32 *p, u32 preset) |
| { |
| u32 i, j, addr; |
| const struct wreg_addr *wreg_addr_p = NULL; |
| |
| if (CHIP_IS_E1(bp)) |
| wreg_addr_p = &wreg_addr_e1; |
| else if (CHIP_IS_E1H(bp)) |
| wreg_addr_p = &wreg_addr_e1h; |
| else if (CHIP_IS_E2(bp)) |
| wreg_addr_p = &wreg_addr_e2; |
| else if (CHIP_IS_E3A0(bp)) |
| wreg_addr_p = &wreg_addr_e3; |
| else if (CHIP_IS_E3B0(bp)) |
| wreg_addr_p = &wreg_addr_e3b0; |
| |
| /* Read the idle_chk registers */ |
| for (i = 0; i < IDLE_REGS_COUNT; i++) { |
| if (bnx2x_is_reg_in_chip(bp, &idle_reg_addrs[i]) && |
| IS_REG_IN_PRESET(idle_reg_addrs[i].presets, preset)) { |
| for (j = 0; j < idle_reg_addrs[i].size; j++) |
| *p++ = REG_RD(bp, idle_reg_addrs[i].addr + j*4); |
| } |
| } |
| |
| /* Read the regular registers */ |
| for (i = 0; i < REGS_COUNT; i++) { |
| if (bnx2x_is_reg_in_chip(bp, ®_addrs[i]) && |
| IS_REG_IN_PRESET(reg_addrs[i].presets, preset)) { |
| for (j = 0; j < reg_addrs[i].size; j++) |
| *p++ = REG_RD(bp, reg_addrs[i].addr + j*4); |
| } |
| } |
| |
| /* Read the CAM registers */ |
| if (bnx2x_is_wreg_in_chip(bp, wreg_addr_p) && |
| IS_REG_IN_PRESET(wreg_addr_p->presets, preset)) { |
| for (i = 0; i < wreg_addr_p->size; i++) { |
| *p++ = REG_RD(bp, wreg_addr_p->addr + i*4); |
| |
| /* In case of wreg_addr register, read additional |
| registers from read_regs array |
| */ |
| for (j = 0; j < wreg_addr_p->read_regs_count; j++) { |
| addr = *(wreg_addr_p->read_regs); |
| *p++ = REG_RD(bp, addr + j*4); |
| } |
| } |
| } |
| |
| /* Paged registers are supported in E2 & E3 only */ |
| if (CHIP_IS_E2(bp) || CHIP_IS_E3(bp)) { |
| /* Read "paged" registers */ |
| bnx2x_read_pages_regs(bp, p, preset); |
| } |
| |
| return 0; |
| } |
| |
| static void __bnx2x_get_regs(struct bnx2x *bp, u32 *p) |
| { |
| u32 preset_idx; |
| |
| /* Read all registers, by reading all preset registers */ |
| for (preset_idx = 1; preset_idx <= DUMP_MAX_PRESETS; preset_idx++) { |
| /* Skip presets with IOR */ |
| if ((preset_idx == 2) || |
| (preset_idx == 5) || |
| (preset_idx == 8) || |
| (preset_idx == 11)) |
| continue; |
| __bnx2x_get_preset_regs(bp, p, preset_idx); |
| p += __bnx2x_get_preset_regs_len(bp, preset_idx); |
| } |
| } |
| |
| static void bnx2x_get_regs(struct net_device *dev, |
| struct ethtool_regs *regs, void *_p) |
| { |
| u32 *p = _p; |
| struct bnx2x *bp = netdev_priv(dev); |
| struct dump_header dump_hdr = {0}; |
| |
| regs->version = 2; |
| memset(p, 0, regs->len); |
| |
| if (!netif_running(bp->dev)) |
| return; |
| |
| /* Disable parity attentions as long as following dump may |
| * cause false alarms by reading never written registers. We |
| * will re-enable parity attentions right after the dump. |
| */ |
| |
| bnx2x_disable_blocks_parity(bp); |
| |
| dump_hdr.header_size = (sizeof(struct dump_header) / 4) - 1; |
| dump_hdr.preset = DUMP_ALL_PRESETS; |
| dump_hdr.version = BNX2X_DUMP_VERSION; |
| |
| /* dump_meta_data presents OR of CHIP and PATH. */ |
| if (CHIP_IS_E1(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E1; |
| } else if (CHIP_IS_E1H(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E1H; |
| } else if (CHIP_IS_E2(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E2 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } else if (CHIP_IS_E3A0(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E3A0 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } else if (CHIP_IS_E3B0(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E3B0 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } |
| |
| memcpy(p, &dump_hdr, sizeof(struct dump_header)); |
| p += dump_hdr.header_size + 1; |
| |
| /* This isn't really an error, but since attention handling is going |
| * to print the GRC timeouts using this macro, we use the same. |
| */ |
| BNX2X_ERR("Generating register dump. Might trigger harmless GRC timeouts\n"); |
| |
| /* Actually read the registers */ |
| __bnx2x_get_regs(bp, p); |
| |
| /* Re-enable parity attentions */ |
| bnx2x_clear_blocks_parity(bp); |
| bnx2x_enable_blocks_parity(bp); |
| } |
| |
| static int bnx2x_get_preset_regs_len(struct net_device *dev, u32 preset) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int regdump_len = 0; |
| |
| regdump_len = __bnx2x_get_preset_regs_len(bp, preset); |
| regdump_len *= 4; |
| regdump_len += sizeof(struct dump_header); |
| |
| return regdump_len; |
| } |
| |
| static int bnx2x_set_dump(struct net_device *dev, struct ethtool_dump *val) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| /* Use the ethtool_dump "flag" field as the dump preset index */ |
| if (val->flag < 1 || val->flag > DUMP_MAX_PRESETS) |
| return -EINVAL; |
| |
| bp->dump_preset_idx = val->flag; |
| return 0; |
| } |
| |
| static int bnx2x_get_dump_flag(struct net_device *dev, |
| struct ethtool_dump *dump) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| dump->version = BNX2X_DUMP_VERSION; |
| dump->flag = bp->dump_preset_idx; |
| /* Calculate the requested preset idx length */ |
| dump->len = bnx2x_get_preset_regs_len(dev, bp->dump_preset_idx); |
| DP(BNX2X_MSG_ETHTOOL, "Get dump preset %d length=%d\n", |
| bp->dump_preset_idx, dump->len); |
| return 0; |
| } |
| |
| static int bnx2x_get_dump_data(struct net_device *dev, |
| struct ethtool_dump *dump, |
| void *buffer) |
| { |
| u32 *p = buffer; |
| struct bnx2x *bp = netdev_priv(dev); |
| struct dump_header dump_hdr = {0}; |
| |
| /* Disable parity attentions as long as following dump may |
| * cause false alarms by reading never written registers. We |
| * will re-enable parity attentions right after the dump. |
| */ |
| |
| bnx2x_disable_blocks_parity(bp); |
| |
| dump_hdr.header_size = (sizeof(struct dump_header) / 4) - 1; |
| dump_hdr.preset = bp->dump_preset_idx; |
| dump_hdr.version = BNX2X_DUMP_VERSION; |
| |
| DP(BNX2X_MSG_ETHTOOL, "Get dump data of preset %d\n", dump_hdr.preset); |
| |
| /* dump_meta_data presents OR of CHIP and PATH. */ |
| if (CHIP_IS_E1(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E1; |
| } else if (CHIP_IS_E1H(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E1H; |
| } else if (CHIP_IS_E2(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E2 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } else if (CHIP_IS_E3A0(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E3A0 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } else if (CHIP_IS_E3B0(bp)) { |
| dump_hdr.dump_meta_data = DUMP_CHIP_E3B0 | |
| (BP_PATH(bp) ? DUMP_PATH_1 : DUMP_PATH_0); |
| } |
| |
| memcpy(p, &dump_hdr, sizeof(struct dump_header)); |
| p += dump_hdr.header_size + 1; |
| |
| /* Actually read the registers */ |
| __bnx2x_get_preset_regs(bp, p, dump_hdr.preset); |
| |
| /* Re-enable parity attentions */ |
| bnx2x_clear_blocks_parity(bp); |
| bnx2x_enable_blocks_parity(bp); |
| |
| return 0; |
| } |
| |
| static void bnx2x_get_drvinfo(struct net_device *dev, |
| struct ethtool_drvinfo *info) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| strlcpy(info->driver, DRV_MODULE_NAME, sizeof(info->driver)); |
| strlcpy(info->version, DRV_MODULE_VERSION, sizeof(info->version)); |
| |
| bnx2x_fill_fw_str(bp, info->fw_version, sizeof(info->fw_version)); |
| |
| strlcpy(info->bus_info, pci_name(bp->pdev), sizeof(info->bus_info)); |
| } |
| |
| static void bnx2x_get_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (bp->flags & NO_WOL_FLAG) { |
| wol->supported = 0; |
| wol->wolopts = 0; |
| } else { |
| wol->supported = WAKE_MAGIC; |
| if (bp->wol) |
| wol->wolopts = WAKE_MAGIC; |
| else |
| wol->wolopts = 0; |
| } |
| memset(&wol->sopass, 0, sizeof(wol->sopass)); |
| } |
| |
| static int bnx2x_set_wol(struct net_device *dev, struct ethtool_wolinfo *wol) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (wol->wolopts & ~WAKE_MAGIC) { |
| DP(BNX2X_MSG_ETHTOOL, "WOL not supported\n"); |
| return -EINVAL; |
| } |
| |
| if (wol->wolopts & WAKE_MAGIC) { |
| if (bp->flags & NO_WOL_FLAG) { |
| DP(BNX2X_MSG_ETHTOOL, "WOL not supported\n"); |
| return -EINVAL; |
| } |
| bp->wol = 1; |
| } else |
| bp->wol = 0; |
| |
| if (SHMEM2_HAS(bp, curr_cfg)) |
| SHMEM2_WR(bp, curr_cfg, CURR_CFG_MET_OS); |
| |
| return 0; |
| } |
| |
| static u32 bnx2x_get_msglevel(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| return bp->msg_enable; |
| } |
| |
| static void bnx2x_set_msglevel(struct net_device *dev, u32 level) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (capable(CAP_NET_ADMIN)) { |
| /* dump MCP trace */ |
| if (IS_PF(bp) && (level & BNX2X_MSG_MCP)) |
| bnx2x_fw_dump_lvl(bp, KERN_INFO); |
| bp->msg_enable = level; |
| } |
| } |
| |
| static int bnx2x_nway_reset(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (!bp->port.pmf) |
| return 0; |
| |
| if (netif_running(dev)) { |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| bnx2x_force_link_reset(bp); |
| bnx2x_link_set(bp); |
| } |
| |
| return 0; |
| } |
| |
| static u32 bnx2x_get_link(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (bp->flags & MF_FUNC_DIS || (bp->state != BNX2X_STATE_OPEN)) |
| return 0; |
| |
| if (IS_VF(bp)) |
| return !test_bit(BNX2X_LINK_REPORT_LINK_DOWN, |
| &bp->vf_link_vars.link_report_flags); |
| |
| return bp->link_vars.link_up; |
| } |
| |
| static int bnx2x_get_eeprom_len(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| return bp->common.flash_size; |
| } |
| |
| /* Per pf misc lock must be acquired before the per port mcp lock. Otherwise, |
| * had we done things the other way around, if two pfs from the same port would |
| * attempt to access nvram at the same time, we could run into a scenario such |
| * as: |
| * pf A takes the port lock. |
| * pf B succeeds in taking the same lock since they are from the same port. |
| * pf A takes the per pf misc lock. Performs eeprom access. |
| * pf A finishes. Unlocks the per pf misc lock. |
| * Pf B takes the lock and proceeds to perform it's own access. |
| * pf A unlocks the per port lock, while pf B is still working (!). |
| * mcp takes the per port lock and corrupts pf B's access (and/or has it's own |
| * access corrupted by pf B) |
| */ |
| static int bnx2x_acquire_nvram_lock(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int count, i; |
| u32 val; |
| |
| /* acquire HW lock: protect against other PFs in PF Direct Assignment */ |
| bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_NVRAM); |
| |
| /* adjust timeout for emulation/FPGA */ |
| count = BNX2X_NVRAM_TIMEOUT_COUNT; |
| if (CHIP_REV_IS_SLOW(bp)) |
| count *= 100; |
| |
| /* request access to nvram interface */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_SW_ARB, |
| (MCPR_NVM_SW_ARB_ARB_REQ_SET1 << port)); |
| |
| for (i = 0; i < count*10; i++) { |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_SW_ARB); |
| if (val & (MCPR_NVM_SW_ARB_ARB_ARB1 << port)) |
| break; |
| |
| udelay(5); |
| } |
| |
| if (!(val & (MCPR_NVM_SW_ARB_ARB_ARB1 << port))) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot get access to nvram interface\n"); |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_NVRAM); |
| return -EBUSY; |
| } |
| |
| return 0; |
| } |
| |
| static int bnx2x_release_nvram_lock(struct bnx2x *bp) |
| { |
| int port = BP_PORT(bp); |
| int count, i; |
| u32 val; |
| |
| /* adjust timeout for emulation/FPGA */ |
| count = BNX2X_NVRAM_TIMEOUT_COUNT; |
| if (CHIP_REV_IS_SLOW(bp)) |
| count *= 100; |
| |
| /* relinquish nvram interface */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_SW_ARB, |
| (MCPR_NVM_SW_ARB_ARB_REQ_CLR1 << port)); |
| |
| for (i = 0; i < count*10; i++) { |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_SW_ARB); |
| if (!(val & (MCPR_NVM_SW_ARB_ARB_ARB1 << port))) |
| break; |
| |
| udelay(5); |
| } |
| |
| if (val & (MCPR_NVM_SW_ARB_ARB_ARB1 << port)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot free access to nvram interface\n"); |
| return -EBUSY; |
| } |
| |
| /* release HW lock: protect against other PFs in PF Direct Assignment */ |
| bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_NVRAM); |
| return 0; |
| } |
| |
| static void bnx2x_enable_nvram_access(struct bnx2x *bp) |
| { |
| u32 val; |
| |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_ACCESS_ENABLE); |
| |
| /* enable both bits, even on read */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_ACCESS_ENABLE, |
| (val | MCPR_NVM_ACCESS_ENABLE_EN | |
| MCPR_NVM_ACCESS_ENABLE_WR_EN)); |
| } |
| |
| static void bnx2x_disable_nvram_access(struct bnx2x *bp) |
| { |
| u32 val; |
| |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_ACCESS_ENABLE); |
| |
| /* disable both bits, even after read */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_ACCESS_ENABLE, |
| (val & ~(MCPR_NVM_ACCESS_ENABLE_EN | |
| MCPR_NVM_ACCESS_ENABLE_WR_EN))); |
| } |
| |
| static int bnx2x_nvram_read_dword(struct bnx2x *bp, u32 offset, __be32 *ret_val, |
| u32 cmd_flags) |
| { |
| int count, i, rc; |
| u32 val; |
| |
| /* build the command word */ |
| cmd_flags |= MCPR_NVM_COMMAND_DOIT; |
| |
| /* need to clear DONE bit separately */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_COMMAND, MCPR_NVM_COMMAND_DONE); |
| |
| /* address of the NVRAM to read from */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_ADDR, |
| (offset & MCPR_NVM_ADDR_NVM_ADDR_VALUE)); |
| |
| /* issue a read command */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_COMMAND, cmd_flags); |
| |
| /* adjust timeout for emulation/FPGA */ |
| count = BNX2X_NVRAM_TIMEOUT_COUNT; |
| if (CHIP_REV_IS_SLOW(bp)) |
| count *= 100; |
| |
| /* wait for completion */ |
| *ret_val = 0; |
| rc = -EBUSY; |
| for (i = 0; i < count; i++) { |
| udelay(5); |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_COMMAND); |
| |
| if (val & MCPR_NVM_COMMAND_DONE) { |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_READ); |
| /* we read nvram data in cpu order |
| * but ethtool sees it as an array of bytes |
| * converting to big-endian will do the work |
| */ |
| *ret_val = cpu_to_be32(val); |
| rc = 0; |
| break; |
| } |
| } |
| if (rc == -EBUSY) |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "nvram read timeout expired\n"); |
| return rc; |
| } |
| |
| int bnx2x_nvram_read(struct bnx2x *bp, u32 offset, u8 *ret_buf, |
| int buf_size) |
| { |
| int rc; |
| u32 cmd_flags; |
| __be32 val; |
| |
| if ((offset & 0x03) || (buf_size & 0x03) || (buf_size == 0)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Invalid parameter: offset 0x%x buf_size 0x%x\n", |
| offset, buf_size); |
| return -EINVAL; |
| } |
| |
| if (offset + buf_size > bp->common.flash_size) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Invalid parameter: offset (0x%x) + buf_size (0x%x) > flash_size (0x%x)\n", |
| offset, buf_size, bp->common.flash_size); |
| return -EINVAL; |
| } |
| |
| /* request access to nvram interface */ |
| rc = bnx2x_acquire_nvram_lock(bp); |
| if (rc) |
| return rc; |
| |
| /* enable access to nvram interface */ |
| bnx2x_enable_nvram_access(bp); |
| |
| /* read the first word(s) */ |
| cmd_flags = MCPR_NVM_COMMAND_FIRST; |
| while ((buf_size > sizeof(u32)) && (rc == 0)) { |
| rc = bnx2x_nvram_read_dword(bp, offset, &val, cmd_flags); |
| memcpy(ret_buf, &val, 4); |
| |
| /* advance to the next dword */ |
| offset += sizeof(u32); |
| ret_buf += sizeof(u32); |
| buf_size -= sizeof(u32); |
| cmd_flags = 0; |
| } |
| |
| if (rc == 0) { |
| cmd_flags |= MCPR_NVM_COMMAND_LAST; |
| rc = bnx2x_nvram_read_dword(bp, offset, &val, cmd_flags); |
| memcpy(ret_buf, &val, 4); |
| } |
| |
| /* disable access to nvram interface */ |
| bnx2x_disable_nvram_access(bp); |
| bnx2x_release_nvram_lock(bp); |
| |
| return rc; |
| } |
| |
| static int bnx2x_nvram_read32(struct bnx2x *bp, u32 offset, u32 *buf, |
| int buf_size) |
| { |
| int rc; |
| |
| rc = bnx2x_nvram_read(bp, offset, (u8 *)buf, buf_size); |
| |
| if (!rc) { |
| __be32 *be = (__be32 *)buf; |
| |
| while ((buf_size -= 4) >= 0) |
| *buf++ = be32_to_cpu(*be++); |
| } |
| |
| return rc; |
| } |
| |
| static bool bnx2x_is_nvm_accessible(struct bnx2x *bp) |
| { |
| int rc = 1; |
| u16 pm = 0; |
| struct net_device *dev = pci_get_drvdata(bp->pdev); |
| |
| if (bp->pdev->pm_cap) |
| rc = pci_read_config_word(bp->pdev, |
| bp->pdev->pm_cap + PCI_PM_CTRL, &pm); |
| |
| if ((rc && !netif_running(dev)) || |
| (!rc && ((pm & PCI_PM_CTRL_STATE_MASK) != (__force u16)PCI_D0))) |
| return false; |
| |
| return true; |
| } |
| |
| static int bnx2x_get_eeprom(struct net_device *dev, |
| struct ethtool_eeprom *eeprom, u8 *eebuf) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -EAGAIN; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, "ethtool_eeprom: cmd %d\n" |
| " magic 0x%x offset 0x%x (%d) len 0x%x (%d)\n", |
| eeprom->cmd, eeprom->magic, eeprom->offset, eeprom->offset, |
| eeprom->len, eeprom->len); |
| |
| /* parameters already validated in ethtool_get_eeprom */ |
| |
| return bnx2x_nvram_read(bp, eeprom->offset, eebuf, eeprom->len); |
| } |
| |
| static int bnx2x_get_module_eeprom(struct net_device *dev, |
| struct ethtool_eeprom *ee, |
| u8 *data) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int rc = -EINVAL, phy_idx; |
| u8 *user_data = data; |
| unsigned int start_addr = ee->offset, xfer_size = 0; |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -EAGAIN; |
| } |
| |
| phy_idx = bnx2x_get_cur_phy_idx(bp); |
| |
| /* Read A0 section */ |
| if (start_addr < ETH_MODULE_SFF_8079_LEN) { |
| /* Limit transfer size to the A0 section boundary */ |
| if (start_addr + ee->len > ETH_MODULE_SFF_8079_LEN) |
| xfer_size = ETH_MODULE_SFF_8079_LEN - start_addr; |
| else |
| xfer_size = ee->len; |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx], |
| &bp->link_params, |
| I2C_DEV_ADDR_A0, |
| start_addr, |
| xfer_size, |
| user_data); |
| bnx2x_release_phy_lock(bp); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL, "Failed reading A0 section\n"); |
| |
| return -EINVAL; |
| } |
| user_data += xfer_size; |
| start_addr += xfer_size; |
| } |
| |
| /* Read A2 section */ |
| if ((start_addr >= ETH_MODULE_SFF_8079_LEN) && |
| (start_addr < ETH_MODULE_SFF_8472_LEN)) { |
| xfer_size = ee->len - xfer_size; |
| /* Limit transfer size to the A2 section boundary */ |
| if (start_addr + xfer_size > ETH_MODULE_SFF_8472_LEN) |
| xfer_size = ETH_MODULE_SFF_8472_LEN - start_addr; |
| start_addr -= ETH_MODULE_SFF_8079_LEN; |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx], |
| &bp->link_params, |
| I2C_DEV_ADDR_A2, |
| start_addr, |
| xfer_size, |
| user_data); |
| bnx2x_release_phy_lock(bp); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL, "Failed reading A2 section\n"); |
| return -EINVAL; |
| } |
| } |
| return rc; |
| } |
| |
| static int bnx2x_get_module_info(struct net_device *dev, |
| struct ethtool_modinfo *modinfo) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int phy_idx, rc; |
| u8 sff8472_comp, diag_type; |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -EAGAIN; |
| } |
| phy_idx = bnx2x_get_cur_phy_idx(bp); |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx], |
| &bp->link_params, |
| I2C_DEV_ADDR_A0, |
| SFP_EEPROM_SFF_8472_COMP_ADDR, |
| SFP_EEPROM_SFF_8472_COMP_SIZE, |
| &sff8472_comp); |
| bnx2x_release_phy_lock(bp); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL, "Failed reading SFF-8472 comp field\n"); |
| return -EINVAL; |
| } |
| |
| bnx2x_acquire_phy_lock(bp); |
| rc = bnx2x_read_sfp_module_eeprom(&bp->link_params.phy[phy_idx], |
| &bp->link_params, |
| I2C_DEV_ADDR_A0, |
| SFP_EEPROM_DIAG_TYPE_ADDR, |
| SFP_EEPROM_DIAG_TYPE_SIZE, |
| &diag_type); |
| bnx2x_release_phy_lock(bp); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL, "Failed reading Diag Type field\n"); |
| return -EINVAL; |
| } |
| |
| if (!sff8472_comp || |
| (diag_type & SFP_EEPROM_DIAG_ADDR_CHANGE_REQ)) { |
| modinfo->type = ETH_MODULE_SFF_8079; |
| modinfo->eeprom_len = ETH_MODULE_SFF_8079_LEN; |
| } else { |
| modinfo->type = ETH_MODULE_SFF_8472; |
| modinfo->eeprom_len = ETH_MODULE_SFF_8472_LEN; |
| } |
| return 0; |
| } |
| |
| static int bnx2x_nvram_write_dword(struct bnx2x *bp, u32 offset, u32 val, |
| u32 cmd_flags) |
| { |
| int count, i, rc; |
| |
| /* build the command word */ |
| cmd_flags |= MCPR_NVM_COMMAND_DOIT | MCPR_NVM_COMMAND_WR; |
| |
| /* need to clear DONE bit separately */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_COMMAND, MCPR_NVM_COMMAND_DONE); |
| |
| /* write the data */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_WRITE, val); |
| |
| /* address of the NVRAM to write to */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_ADDR, |
| (offset & MCPR_NVM_ADDR_NVM_ADDR_VALUE)); |
| |
| /* issue the write command */ |
| REG_WR(bp, MCP_REG_MCPR_NVM_COMMAND, cmd_flags); |
| |
| /* adjust timeout for emulation/FPGA */ |
| count = BNX2X_NVRAM_TIMEOUT_COUNT; |
| if (CHIP_REV_IS_SLOW(bp)) |
| count *= 100; |
| |
| /* wait for completion */ |
| rc = -EBUSY; |
| for (i = 0; i < count; i++) { |
| udelay(5); |
| val = REG_RD(bp, MCP_REG_MCPR_NVM_COMMAND); |
| if (val & MCPR_NVM_COMMAND_DONE) { |
| rc = 0; |
| break; |
| } |
| } |
| |
| if (rc == -EBUSY) |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "nvram write timeout expired\n"); |
| return rc; |
| } |
| |
| #define BYTE_OFFSET(offset) (8 * (offset & 0x03)) |
| |
| static int bnx2x_nvram_write1(struct bnx2x *bp, u32 offset, u8 *data_buf, |
| int buf_size) |
| { |
| int rc; |
| u32 cmd_flags, align_offset, val; |
| __be32 val_be; |
| |
| if (offset + buf_size > bp->common.flash_size) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Invalid parameter: offset (0x%x) + buf_size (0x%x) > flash_size (0x%x)\n", |
| offset, buf_size, bp->common.flash_size); |
| return -EINVAL; |
| } |
| |
| /* request access to nvram interface */ |
| rc = bnx2x_acquire_nvram_lock(bp); |
| if (rc) |
| return rc; |
| |
| /* enable access to nvram interface */ |
| bnx2x_enable_nvram_access(bp); |
| |
| cmd_flags = (MCPR_NVM_COMMAND_FIRST | MCPR_NVM_COMMAND_LAST); |
| align_offset = (offset & ~0x03); |
| rc = bnx2x_nvram_read_dword(bp, align_offset, &val_be, cmd_flags); |
| |
| if (rc == 0) { |
| /* nvram data is returned as an array of bytes |
| * convert it back to cpu order |
| */ |
| val = be32_to_cpu(val_be); |
| |
| val &= ~le32_to_cpu((__force __le32) |
| (0xff << BYTE_OFFSET(offset))); |
| val |= le32_to_cpu((__force __le32) |
| (*data_buf << BYTE_OFFSET(offset))); |
| |
| rc = bnx2x_nvram_write_dword(bp, align_offset, val, |
| cmd_flags); |
| } |
| |
| /* disable access to nvram interface */ |
| bnx2x_disable_nvram_access(bp); |
| bnx2x_release_nvram_lock(bp); |
| |
| return rc; |
| } |
| |
| static int bnx2x_nvram_write(struct bnx2x *bp, u32 offset, u8 *data_buf, |
| int buf_size) |
| { |
| int rc; |
| u32 cmd_flags; |
| u32 val; |
| u32 written_so_far; |
| |
| if (buf_size == 1) /* ethtool */ |
| return bnx2x_nvram_write1(bp, offset, data_buf, buf_size); |
| |
| if ((offset & 0x03) || (buf_size & 0x03) || (buf_size == 0)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Invalid parameter: offset 0x%x buf_size 0x%x\n", |
| offset, buf_size); |
| return -EINVAL; |
| } |
| |
| if (offset + buf_size > bp->common.flash_size) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Invalid parameter: offset (0x%x) + buf_size (0x%x) > flash_size (0x%x)\n", |
| offset, buf_size, bp->common.flash_size); |
| return -EINVAL; |
| } |
| |
| /* request access to nvram interface */ |
| rc = bnx2x_acquire_nvram_lock(bp); |
| if (rc) |
| return rc; |
| |
| /* enable access to nvram interface */ |
| bnx2x_enable_nvram_access(bp); |
| |
| written_so_far = 0; |
| cmd_flags = MCPR_NVM_COMMAND_FIRST; |
| while ((written_so_far < buf_size) && (rc == 0)) { |
| if (written_so_far == (buf_size - sizeof(u32))) |
| cmd_flags |= MCPR_NVM_COMMAND_LAST; |
| else if (((offset + 4) % BNX2X_NVRAM_PAGE_SIZE) == 0) |
| cmd_flags |= MCPR_NVM_COMMAND_LAST; |
| else if ((offset % BNX2X_NVRAM_PAGE_SIZE) == 0) |
| cmd_flags |= MCPR_NVM_COMMAND_FIRST; |
| |
| memcpy(&val, data_buf, 4); |
| |
| /* Notice unlike bnx2x_nvram_read_dword() this will not |
| * change val using be32_to_cpu(), which causes data to flip |
| * if the eeprom is read and then written back. This is due |
| * to tools utilizing this functionality that would break |
| * if this would be resolved. |
| */ |
| rc = bnx2x_nvram_write_dword(bp, offset, val, cmd_flags); |
| |
| /* advance to the next dword */ |
| offset += sizeof(u32); |
| data_buf += sizeof(u32); |
| written_so_far += sizeof(u32); |
| |
| /* At end of each 4Kb page, release nvram lock to allow MFW |
| * chance to take it for its own use. |
| */ |
| if ((cmd_flags & MCPR_NVM_COMMAND_LAST) && |
| (written_so_far < buf_size)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Releasing NVM lock after offset 0x%x\n", |
| (u32)(offset - sizeof(u32))); |
| bnx2x_release_nvram_lock(bp); |
| usleep_range(1000, 2000); |
| rc = bnx2x_acquire_nvram_lock(bp); |
| if (rc) |
| return rc; |
| } |
| |
| cmd_flags = 0; |
| } |
| |
| /* disable access to nvram interface */ |
| bnx2x_disable_nvram_access(bp); |
| bnx2x_release_nvram_lock(bp); |
| |
| return rc; |
| } |
| |
| static int bnx2x_set_eeprom(struct net_device *dev, |
| struct ethtool_eeprom *eeprom, u8 *eebuf) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int port = BP_PORT(bp); |
| int rc = 0; |
| u32 ext_phy_config; |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -EAGAIN; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, "ethtool_eeprom: cmd %d\n" |
| " magic 0x%x offset 0x%x (%d) len 0x%x (%d)\n", |
| eeprom->cmd, eeprom->magic, eeprom->offset, eeprom->offset, |
| eeprom->len, eeprom->len); |
| |
| /* parameters already validated in ethtool_set_eeprom */ |
| |
| /* PHY eeprom can be accessed only by the PMF */ |
| if ((eeprom->magic >= 0x50485900) && (eeprom->magic <= 0x504859FF) && |
| !bp->port.pmf) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "wrong magic or interface is not pmf\n"); |
| return -EINVAL; |
| } |
| |
| ext_phy_config = |
| SHMEM_RD(bp, |
| dev_info.port_hw_config[port].external_phy_config); |
| |
| if (eeprom->magic == 0x50485950) { |
| /* 'PHYP' (0x50485950): prepare phy for FW upgrade */ |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| |
| bnx2x_acquire_phy_lock(bp); |
| rc |= bnx2x_link_reset(&bp->link_params, |
| &bp->link_vars, 0); |
| if (XGXS_EXT_PHY_TYPE(ext_phy_config) == |
| PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) |
| bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, |
| MISC_REGISTERS_GPIO_HIGH, port); |
| bnx2x_release_phy_lock(bp); |
| bnx2x_link_report(bp); |
| |
| } else if (eeprom->magic == 0x50485952) { |
| /* 'PHYR' (0x50485952): re-init link after FW upgrade */ |
| if (bp->state == BNX2X_STATE_OPEN) { |
| bnx2x_acquire_phy_lock(bp); |
| rc |= bnx2x_link_reset(&bp->link_params, |
| &bp->link_vars, 1); |
| |
| rc |= bnx2x_phy_init(&bp->link_params, |
| &bp->link_vars); |
| bnx2x_release_phy_lock(bp); |
| bnx2x_calc_fc_adv(bp); |
| } |
| } else if (eeprom->magic == 0x53985943) { |
| /* 'PHYC' (0x53985943): PHY FW upgrade completed */ |
| if (XGXS_EXT_PHY_TYPE(ext_phy_config) == |
| PORT_HW_CFG_XGXS_EXT_PHY_TYPE_SFX7101) { |
| |
| /* DSP Remove Download Mode */ |
| bnx2x_set_gpio(bp, MISC_REGISTERS_GPIO_0, |
| MISC_REGISTERS_GPIO_LOW, port); |
| |
| bnx2x_acquire_phy_lock(bp); |
| |
| bnx2x_sfx7101_sp_sw_reset(bp, |
| &bp->link_params.phy[EXT_PHY1]); |
| |
| /* wait 0.5 sec to allow it to run */ |
| msleep(500); |
| bnx2x_ext_phy_hw_reset(bp, port); |
| msleep(500); |
| bnx2x_release_phy_lock(bp); |
| } |
| } else |
| rc = bnx2x_nvram_write(bp, eeprom->offset, eebuf, eeprom->len); |
| |
| return rc; |
| } |
| |
| static int bnx2x_get_coalesce(struct net_device *dev, |
| struct ethtool_coalesce *coal) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| memset(coal, 0, sizeof(struct ethtool_coalesce)); |
| |
| coal->rx_coalesce_usecs = bp->rx_ticks; |
| coal->tx_coalesce_usecs = bp->tx_ticks; |
| |
| return 0; |
| } |
| |
| static int bnx2x_set_coalesce(struct net_device *dev, |
| struct ethtool_coalesce *coal) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| bp->rx_ticks = (u16)coal->rx_coalesce_usecs; |
| if (bp->rx_ticks > BNX2X_MAX_COALESCE_TOUT) |
| bp->rx_ticks = BNX2X_MAX_COALESCE_TOUT; |
| |
| bp->tx_ticks = (u16)coal->tx_coalesce_usecs; |
| if (bp->tx_ticks > BNX2X_MAX_COALESCE_TOUT) |
| bp->tx_ticks = BNX2X_MAX_COALESCE_TOUT; |
| |
| if (netif_running(dev)) |
| bnx2x_update_coalesce(bp); |
| |
| return 0; |
| } |
| |
| static void bnx2x_get_ringparam(struct net_device *dev, |
| struct ethtool_ringparam *ering) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| ering->rx_max_pending = MAX_RX_AVAIL; |
| |
| /* If size isn't already set, we give an estimation of the number |
| * of buffers we'll have. We're neglecting some possible conditions |
| * [we couldn't know for certain at this point if number of queues |
| * might shrink] but the number would be correct for the likely |
| * scenario. |
| */ |
| if (bp->rx_ring_size) |
| ering->rx_pending = bp->rx_ring_size; |
| else if (BNX2X_NUM_RX_QUEUES(bp)) |
| ering->rx_pending = MAX_RX_AVAIL / BNX2X_NUM_RX_QUEUES(bp); |
| else |
| ering->rx_pending = MAX_RX_AVAIL; |
| |
| ering->tx_max_pending = IS_MF_FCOE_AFEX(bp) ? 0 : MAX_TX_AVAIL; |
| ering->tx_pending = bp->tx_ring_size; |
| } |
| |
| static int bnx2x_set_ringparam(struct net_device *dev, |
| struct ethtool_ringparam *ering) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| DP(BNX2X_MSG_ETHTOOL, |
| "set ring params command parameters: rx_pending = %d, tx_pending = %d\n", |
| ering->rx_pending, ering->tx_pending); |
| |
| if (pci_num_vf(bp->pdev)) { |
| DP(BNX2X_MSG_IOV, |
| "VFs are enabled, can not change ring parameters\n"); |
| return -EPERM; |
| } |
| |
| if (bp->recovery_state != BNX2X_RECOVERY_DONE) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Handling parity error recovery. Try again later\n"); |
| return -EAGAIN; |
| } |
| |
| if ((ering->rx_pending > MAX_RX_AVAIL) || |
| (ering->rx_pending < (bp->disable_tpa ? MIN_RX_SIZE_NONTPA : |
| MIN_RX_SIZE_TPA)) || |
| (ering->tx_pending > (IS_MF_STORAGE_ONLY(bp) ? 0 : MAX_TX_AVAIL)) || |
| (ering->tx_pending <= MAX_SKB_FRAGS + 4)) { |
| DP(BNX2X_MSG_ETHTOOL, "Command parameters not supported\n"); |
| return -EINVAL; |
| } |
| |
| bp->rx_ring_size = ering->rx_pending; |
| bp->tx_ring_size = ering->tx_pending; |
| |
| return bnx2x_reload_if_running(dev); |
| } |
| |
| static void bnx2x_get_pauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *epause) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| int cfg_reg; |
| |
| epause->autoneg = (bp->link_params.req_flow_ctrl[cfg_idx] == |
| BNX2X_FLOW_CTRL_AUTO); |
| |
| if (!epause->autoneg) |
| cfg_reg = bp->link_params.req_flow_ctrl[cfg_idx]; |
| else |
| cfg_reg = bp->link_params.req_fc_auto_adv; |
| |
| epause->rx_pause = ((cfg_reg & BNX2X_FLOW_CTRL_RX) == |
| BNX2X_FLOW_CTRL_RX); |
| epause->tx_pause = ((cfg_reg & BNX2X_FLOW_CTRL_TX) == |
| BNX2X_FLOW_CTRL_TX); |
| |
| DP(BNX2X_MSG_ETHTOOL, "ethtool_pauseparam: cmd %d\n" |
| " autoneg %d rx_pause %d tx_pause %d\n", |
| epause->cmd, epause->autoneg, epause->rx_pause, epause->tx_pause); |
| } |
| |
| static int bnx2x_set_pauseparam(struct net_device *dev, |
| struct ethtool_pauseparam *epause) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| if (IS_MF(bp)) |
| return 0; |
| |
| DP(BNX2X_MSG_ETHTOOL, "ethtool_pauseparam: cmd %d\n" |
| " autoneg %d rx_pause %d tx_pause %d\n", |
| epause->cmd, epause->autoneg, epause->rx_pause, epause->tx_pause); |
| |
| bp->link_params.req_flow_ctrl[cfg_idx] = BNX2X_FLOW_CTRL_AUTO; |
| |
| if (epause->rx_pause) |
| bp->link_params.req_flow_ctrl[cfg_idx] |= BNX2X_FLOW_CTRL_RX; |
| |
| if (epause->tx_pause) |
| bp->link_params.req_flow_ctrl[cfg_idx] |= BNX2X_FLOW_CTRL_TX; |
| |
| if (bp->link_params.req_flow_ctrl[cfg_idx] == BNX2X_FLOW_CTRL_AUTO) |
| bp->link_params.req_flow_ctrl[cfg_idx] = BNX2X_FLOW_CTRL_NONE; |
| |
| if (epause->autoneg) { |
| if (!(bp->port.supported[cfg_idx] & SUPPORTED_Autoneg)) { |
| DP(BNX2X_MSG_ETHTOOL, "autoneg not supported\n"); |
| return -EINVAL; |
| } |
| |
| if (bp->link_params.req_line_speed[cfg_idx] == SPEED_AUTO_NEG) { |
| bp->link_params.req_flow_ctrl[cfg_idx] = |
| BNX2X_FLOW_CTRL_AUTO; |
| } |
| bp->link_params.req_fc_auto_adv = 0; |
| if (epause->rx_pause) |
| bp->link_params.req_fc_auto_adv |= BNX2X_FLOW_CTRL_RX; |
| |
| if (epause->tx_pause) |
| bp->link_params.req_fc_auto_adv |= BNX2X_FLOW_CTRL_TX; |
| |
| if (!bp->link_params.req_fc_auto_adv) |
| bp->link_params.req_fc_auto_adv |= BNX2X_FLOW_CTRL_NONE; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL, |
| "req_flow_ctrl 0x%x\n", bp->link_params.req_flow_ctrl[cfg_idx]); |
| |
| if (netif_running(dev)) { |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| bnx2x_force_link_reset(bp); |
| bnx2x_link_set(bp); |
| } |
| |
| return 0; |
| } |
| |
| static const char bnx2x_tests_str_arr[BNX2X_NUM_TESTS_SF][ETH_GSTRING_LEN] = { |
| "register_test (offline) ", |
| "memory_test (offline) ", |
| "int_loopback_test (offline)", |
| "ext_loopback_test (offline)", |
| "nvram_test (online) ", |
| "interrupt_test (online) ", |
| "link_test (online) " |
| }; |
| |
| enum { |
| BNX2X_PRI_FLAG_ISCSI, |
| BNX2X_PRI_FLAG_FCOE, |
| BNX2X_PRI_FLAG_STORAGE, |
| BNX2X_PRI_FLAG_LEN, |
| }; |
| |
| static const char bnx2x_private_arr[BNX2X_PRI_FLAG_LEN][ETH_GSTRING_LEN] = { |
| "iSCSI offload support", |
| "FCoE offload support", |
| "Storage only interface" |
| }; |
| |
| static u32 bnx2x_eee_to_adv(u32 eee_adv) |
| { |
| u32 modes = 0; |
| |
| if (eee_adv & SHMEM_EEE_100M_ADV) |
| modes |= ADVERTISED_100baseT_Full; |
| if (eee_adv & SHMEM_EEE_1G_ADV) |
| modes |= ADVERTISED_1000baseT_Full; |
| if (eee_adv & SHMEM_EEE_10G_ADV) |
| modes |= ADVERTISED_10000baseT_Full; |
| |
| return modes; |
| } |
| |
| static u32 bnx2x_adv_to_eee(u32 modes, u32 shift) |
| { |
| u32 eee_adv = 0; |
| if (modes & ADVERTISED_100baseT_Full) |
| eee_adv |= SHMEM_EEE_100M_ADV; |
| if (modes & ADVERTISED_1000baseT_Full) |
| eee_adv |= SHMEM_EEE_1G_ADV; |
| if (modes & ADVERTISED_10000baseT_Full) |
| eee_adv |= SHMEM_EEE_10G_ADV; |
| |
| return eee_adv << shift; |
| } |
| |
| static int bnx2x_get_eee(struct net_device *dev, struct ethtool_eee *edata) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 eee_cfg; |
| |
| if (!SHMEM2_HAS(bp, eee_status[BP_PORT(bp)])) { |
| DP(BNX2X_MSG_ETHTOOL, "BC Version does not support EEE\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| eee_cfg = bp->link_vars.eee_status; |
| |
| edata->supported = |
| bnx2x_eee_to_adv((eee_cfg & SHMEM_EEE_SUPPORTED_MASK) >> |
| SHMEM_EEE_SUPPORTED_SHIFT); |
| |
| edata->advertised = |
| bnx2x_eee_to_adv((eee_cfg & SHMEM_EEE_ADV_STATUS_MASK) >> |
| SHMEM_EEE_ADV_STATUS_SHIFT); |
| edata->lp_advertised = |
| bnx2x_eee_to_adv((eee_cfg & SHMEM_EEE_LP_ADV_STATUS_MASK) >> |
| SHMEM_EEE_LP_ADV_STATUS_SHIFT); |
| |
| /* SHMEM value is in 16u units --> Convert to 1u units. */ |
| edata->tx_lpi_timer = (eee_cfg & SHMEM_EEE_TIMER_MASK) << 4; |
| |
| edata->eee_enabled = (eee_cfg & SHMEM_EEE_REQUESTED_BIT) ? 1 : 0; |
| edata->eee_active = (eee_cfg & SHMEM_EEE_ACTIVE_BIT) ? 1 : 0; |
| edata->tx_lpi_enabled = (eee_cfg & SHMEM_EEE_LPI_REQUESTED_BIT) ? 1 : 0; |
| |
| return 0; |
| } |
| |
| static int bnx2x_set_eee(struct net_device *dev, struct ethtool_eee *edata) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 eee_cfg; |
| u32 advertised; |
| |
| if (IS_MF(bp)) |
| return 0; |
| |
| if (!SHMEM2_HAS(bp, eee_status[BP_PORT(bp)])) { |
| DP(BNX2X_MSG_ETHTOOL, "BC Version does not support EEE\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| eee_cfg = bp->link_vars.eee_status; |
| |
| if (!(eee_cfg & SHMEM_EEE_SUPPORTED_MASK)) { |
| DP(BNX2X_MSG_ETHTOOL, "Board does not support EEE!\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| advertised = bnx2x_adv_to_eee(edata->advertised, |
| SHMEM_EEE_ADV_STATUS_SHIFT); |
| if ((advertised != (eee_cfg & SHMEM_EEE_ADV_STATUS_MASK))) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Direct manipulation of EEE advertisement is not supported\n"); |
| return -EINVAL; |
| } |
| |
| if (edata->tx_lpi_timer > EEE_MODE_TIMER_MASK) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Maximal Tx Lpi timer supported is %x(u)\n", |
| EEE_MODE_TIMER_MASK); |
| return -EINVAL; |
| } |
| if (edata->tx_lpi_enabled && |
| (edata->tx_lpi_timer < EEE_MODE_NVRAM_AGGRESSIVE_TIME)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Minimal Tx Lpi timer supported is %d(u)\n", |
| EEE_MODE_NVRAM_AGGRESSIVE_TIME); |
| return -EINVAL; |
| } |
| |
| /* All is well; Apply changes*/ |
| if (edata->eee_enabled) |
| bp->link_params.eee_mode |= EEE_MODE_ADV_LPI; |
| else |
| bp->link_params.eee_mode &= ~EEE_MODE_ADV_LPI; |
| |
| if (edata->tx_lpi_enabled) |
| bp->link_params.eee_mode |= EEE_MODE_ENABLE_LPI; |
| else |
| bp->link_params.eee_mode &= ~EEE_MODE_ENABLE_LPI; |
| |
| bp->link_params.eee_mode &= ~EEE_MODE_TIMER_MASK; |
| bp->link_params.eee_mode |= (edata->tx_lpi_timer & |
| EEE_MODE_TIMER_MASK) | |
| EEE_MODE_OVERRIDE_NVRAM | |
| EEE_MODE_OUTPUT_TIME; |
| |
| /* Restart link to propagate changes */ |
| if (netif_running(dev)) { |
| bnx2x_stats_handle(bp, STATS_EVENT_STOP); |
| bnx2x_force_link_reset(bp); |
| bnx2x_link_set(bp); |
| } |
| |
| return 0; |
| } |
| |
| enum { |
| BNX2X_CHIP_E1_OFST = 0, |
| BNX2X_CHIP_E1H_OFST, |
| BNX2X_CHIP_E2_OFST, |
| BNX2X_CHIP_E3_OFST, |
| BNX2X_CHIP_E3B0_OFST, |
| BNX2X_CHIP_MAX_OFST |
| }; |
| |
| #define BNX2X_CHIP_MASK_E1 (1 << BNX2X_CHIP_E1_OFST) |
| #define BNX2X_CHIP_MASK_E1H (1 << BNX2X_CHIP_E1H_OFST) |
| #define BNX2X_CHIP_MASK_E2 (1 << BNX2X_CHIP_E2_OFST) |
| #define BNX2X_CHIP_MASK_E3 (1 << BNX2X_CHIP_E3_OFST) |
| #define BNX2X_CHIP_MASK_E3B0 (1 << BNX2X_CHIP_E3B0_OFST) |
| |
| #define BNX2X_CHIP_MASK_ALL ((1 << BNX2X_CHIP_MAX_OFST) - 1) |
| #define BNX2X_CHIP_MASK_E1X (BNX2X_CHIP_MASK_E1 | BNX2X_CHIP_MASK_E1H) |
| |
| static int bnx2x_test_registers(struct bnx2x *bp) |
| { |
| int idx, i, rc = -ENODEV; |
| u32 wr_val = 0, hw; |
| int port = BP_PORT(bp); |
| static const struct { |
| u32 hw; |
| u32 offset0; |
| u32 offset1; |
| u32 mask; |
| } reg_tbl[] = { |
| /* 0 */ { BNX2X_CHIP_MASK_ALL, |
| BRB1_REG_PAUSE_LOW_THRESHOLD_0, 4, 0x000003ff }, |
| { BNX2X_CHIP_MASK_ALL, |
| DORQ_REG_DB_ADDR0, 4, 0xffffffff }, |
| { BNX2X_CHIP_MASK_E1X, |
| HC_REG_AGG_INT_0, 4, 0x000003ff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PBF_REG_MAC_IF0_ENABLE, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2 | BNX2X_CHIP_MASK_E3, |
| PBF_REG_P0_INIT_CRD, 4, 0x000007ff }, |
| { BNX2X_CHIP_MASK_E3B0, |
| PBF_REG_INIT_CRD_Q0, 4, 0x000007ff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PRS_REG_CID_PORT_0, 4, 0x00ffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PXP2_REG_PSWRQ_CDU0_L2P, 4, 0x000fffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PXP2_REG_RQ_CDU0_EFIRST_MEM_ADDR, 8, 0x0003ffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PXP2_REG_PSWRQ_TM0_L2P, 4, 0x000fffff }, |
| /* 10 */ { BNX2X_CHIP_MASK_ALL, |
| PXP2_REG_RQ_USDM0_EFIRST_MEM_ADDR, 8, 0x0003ffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| PXP2_REG_PSWRQ_TSDM0_L2P, 4, 0x000fffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| QM_REG_CONNNUM_0, 4, 0x000fffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| TM_REG_LIN0_MAX_ACTIVE_CID, 4, 0x0003ffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| SRC_REG_KEYRSS0_0, 40, 0xffffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| SRC_REG_KEYRSS0_7, 40, 0xffffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| XCM_REG_WU_DA_SET_TMR_CNT_FLG_CMD00, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_ALL, |
| XCM_REG_WU_DA_CNT_CMD00, 4, 0x00000003 }, |
| { BNX2X_CHIP_MASK_ALL, |
| XCM_REG_GLB_DEL_ACK_MAX_CNT_0, 4, 0x000000ff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_T_BIT, 4, 0x00000001 }, |
| /* 20 */ { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2, |
| NIG_REG_EMAC0_IN_EN, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2, |
| NIG_REG_BMAC0_IN_EN, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_XCM0_OUT_EN, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_BRB0_OUT_EN, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_XCM_MASK, 4, 0x00000007 }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_ACPI_PAT_6_LEN, 68, 0x000000ff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_ACPI_PAT_0_CRC, 68, 0xffffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_DEST_MAC_0_0, 160, 0xffffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_DEST_IP_0_1, 160, 0xffffffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_IPV4_IPV6_0, 160, 0x00000001 }, |
| /* 30 */ { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_DEST_UDP_0, 160, 0x0000ffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_DEST_TCP_0, 160, 0x0000ffff }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LLH0_VLAN_ID_0, 160, 0x00000fff }, |
| { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2, |
| NIG_REG_XGXS_SERDES0_MODE_SEL, 4, 0x00000001 }, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_LED_CONTROL_OVERRIDE_TRAFFIC_P0, 4, 0x00000001}, |
| { BNX2X_CHIP_MASK_ALL, |
| NIG_REG_STATUS_INTERRUPT_PORT0, 4, 0x07ffffff }, |
| { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2, |
| NIG_REG_XGXS0_CTRL_EXTREMOTEMDIOST, 24, 0x00000001 }, |
| { BNX2X_CHIP_MASK_E1X | BNX2X_CHIP_MASK_E2, |
| NIG_REG_SERDES0_CTRL_PHY_ADDR, 16, 0x0000001f }, |
| |
| { BNX2X_CHIP_MASK_ALL, 0xffffffff, 0, 0x00000000 } |
| }; |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return rc; |
| } |
| |
| if (CHIP_IS_E1(bp)) |
| hw = BNX2X_CHIP_MASK_E1; |
| else if (CHIP_IS_E1H(bp)) |
| hw = BNX2X_CHIP_MASK_E1H; |
| else if (CHIP_IS_E2(bp)) |
| hw = BNX2X_CHIP_MASK_E2; |
| else if (CHIP_IS_E3B0(bp)) |
| hw = BNX2X_CHIP_MASK_E3B0; |
| else /* e3 A0 */ |
| hw = BNX2X_CHIP_MASK_E3; |
| |
| /* Repeat the test twice: |
| * First by writing 0x00000000, second by writing 0xffffffff |
| */ |
| for (idx = 0; idx < 2; idx++) { |
| |
| switch (idx) { |
| case 0: |
| wr_val = 0; |
| break; |
| case 1: |
| wr_val = 0xffffffff; |
| break; |
| } |
| |
| for (i = 0; reg_tbl[i].offset0 != 0xffffffff; i++) { |
| u32 offset, mask, save_val, val; |
| if (!(hw & reg_tbl[i].hw)) |
| continue; |
| |
| offset = reg_tbl[i].offset0 + port*reg_tbl[i].offset1; |
| mask = reg_tbl[i].mask; |
| |
| save_val = REG_RD(bp, offset); |
| |
| REG_WR(bp, offset, wr_val & mask); |
| |
| val = REG_RD(bp, offset); |
| |
| /* Restore the original register's value */ |
| REG_WR(bp, offset, save_val); |
| |
| /* verify value is as expected */ |
| if ((val & mask) != (wr_val & mask)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "offset 0x%x: val 0x%x != 0x%x mask 0x%x\n", |
| offset, val, wr_val, mask); |
| goto test_reg_exit; |
| } |
| } |
| } |
| |
| rc = 0; |
| |
| test_reg_exit: |
| return rc; |
| } |
| |
| static int bnx2x_test_memory(struct bnx2x *bp) |
| { |
| int i, j, rc = -ENODEV; |
| u32 val, index; |
| static const struct { |
| u32 offset; |
| int size; |
| } mem_tbl[] = { |
| { CCM_REG_XX_DESCR_TABLE, CCM_REG_XX_DESCR_TABLE_SIZE }, |
| { CFC_REG_ACTIVITY_COUNTER, CFC_REG_ACTIVITY_COUNTER_SIZE }, |
| { CFC_REG_LINK_LIST, CFC_REG_LINK_LIST_SIZE }, |
| { DMAE_REG_CMD_MEM, DMAE_REG_CMD_MEM_SIZE }, |
| { TCM_REG_XX_DESCR_TABLE, TCM_REG_XX_DESCR_TABLE_SIZE }, |
| { UCM_REG_XX_DESCR_TABLE, UCM_REG_XX_DESCR_TABLE_SIZE }, |
| { XCM_REG_XX_DESCR_TABLE, XCM_REG_XX_DESCR_TABLE_SIZE }, |
| |
| { 0xffffffff, 0 } |
| }; |
| |
| static const struct { |
| char *name; |
| u32 offset; |
| u32 hw_mask[BNX2X_CHIP_MAX_OFST]; |
| } prty_tbl[] = { |
| { "CCM_PRTY_STS", CCM_REG_CCM_PRTY_STS, |
| {0x3ffc0, 0, 0, 0} }, |
| { "CFC_PRTY_STS", CFC_REG_CFC_PRTY_STS, |
| {0x2, 0x2, 0, 0} }, |
| { "DMAE_PRTY_STS", DMAE_REG_DMAE_PRTY_STS, |
| {0, 0, 0, 0} }, |
| { "TCM_PRTY_STS", TCM_REG_TCM_PRTY_STS, |
| {0x3ffc0, 0, 0, 0} }, |
| { "UCM_PRTY_STS", UCM_REG_UCM_PRTY_STS, |
| {0x3ffc0, 0, 0, 0} }, |
| { "XCM_PRTY_STS", XCM_REG_XCM_PRTY_STS, |
| {0x3ffc1, 0, 0, 0} }, |
| |
| { NULL, 0xffffffff, {0, 0, 0, 0} } |
| }; |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return rc; |
| } |
| |
| if (CHIP_IS_E1(bp)) |
| index = BNX2X_CHIP_E1_OFST; |
| else if (CHIP_IS_E1H(bp)) |
| index = BNX2X_CHIP_E1H_OFST; |
| else if (CHIP_IS_E2(bp)) |
| index = BNX2X_CHIP_E2_OFST; |
| else /* e3 */ |
| index = BNX2X_CHIP_E3_OFST; |
| |
| /* pre-Check the parity status */ |
| for (i = 0; prty_tbl[i].offset != 0xffffffff; i++) { |
| val = REG_RD(bp, prty_tbl[i].offset); |
| if (val & ~(prty_tbl[i].hw_mask[index])) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "%s is 0x%x\n", prty_tbl[i].name, val); |
| goto test_mem_exit; |
| } |
| } |
| |
| /* Go through all the memories */ |
| for (i = 0; mem_tbl[i].offset != 0xffffffff; i++) |
| for (j = 0; j < mem_tbl[i].size; j++) |
| REG_RD(bp, mem_tbl[i].offset + j*4); |
| |
| /* Check the parity status */ |
| for (i = 0; prty_tbl[i].offset != 0xffffffff; i++) { |
| val = REG_RD(bp, prty_tbl[i].offset); |
| if (val & ~(prty_tbl[i].hw_mask[index])) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "%s is 0x%x\n", prty_tbl[i].name, val); |
| goto test_mem_exit; |
| } |
| } |
| |
| rc = 0; |
| |
| test_mem_exit: |
| return rc; |
| } |
| |
| static void bnx2x_wait_for_link(struct bnx2x *bp, u8 link_up, u8 is_serdes) |
| { |
| int cnt = 1400; |
| |
| if (link_up) { |
| while (bnx2x_link_test(bp, is_serdes) && cnt--) |
| msleep(20); |
| |
| if (cnt <= 0 && bnx2x_link_test(bp, is_serdes)) |
| DP(BNX2X_MSG_ETHTOOL, "Timeout waiting for link up\n"); |
| |
| cnt = 1400; |
| while (!bp->link_vars.link_up && cnt--) |
| msleep(20); |
| |
| if (cnt <= 0 && !bp->link_vars.link_up) |
| DP(BNX2X_MSG_ETHTOOL, |
| "Timeout waiting for link init\n"); |
| } |
| } |
| |
| static int bnx2x_run_loopback(struct bnx2x *bp, int loopback_mode) |
| { |
| unsigned int pkt_size, num_pkts, i; |
| struct sk_buff *skb; |
| unsigned char *packet; |
| struct bnx2x_fastpath *fp_rx = &bp->fp[0]; |
| struct bnx2x_fastpath *fp_tx = &bp->fp[0]; |
| struct bnx2x_fp_txdata *txdata = fp_tx->txdata_ptr[0]; |
| u16 tx_start_idx, tx_idx; |
| u16 rx_start_idx, rx_idx; |
| u16 pkt_prod, bd_prod; |
| struct sw_tx_bd *tx_buf; |
| struct eth_tx_start_bd *tx_start_bd; |
| dma_addr_t mapping; |
| union eth_rx_cqe *cqe; |
| u8 cqe_fp_flags, cqe_fp_type; |
| struct sw_rx_bd *rx_buf; |
| u16 len; |
| int rc = -ENODEV; |
| u8 *data; |
| struct netdev_queue *txq = netdev_get_tx_queue(bp->dev, |
| txdata->txq_index); |
| |
| /* check the loopback mode */ |
| switch (loopback_mode) { |
| case BNX2X_PHY_LOOPBACK: |
| if (bp->link_params.loopback_mode != LOOPBACK_XGXS) { |
| DP(BNX2X_MSG_ETHTOOL, "PHY loopback not supported\n"); |
| return -EINVAL; |
| } |
| break; |
| case BNX2X_MAC_LOOPBACK: |
| if (CHIP_IS_E3(bp)) { |
| int cfg_idx = bnx2x_get_link_cfg_idx(bp); |
| if (bp->port.supported[cfg_idx] & |
| (SUPPORTED_10000baseT_Full | |
| SUPPORTED_20000baseMLD2_Full | |
| SUPPORTED_20000baseKR2_Full)) |
| bp->link_params.loopback_mode = LOOPBACK_XMAC; |
| else |
| bp->link_params.loopback_mode = LOOPBACK_UMAC; |
| } else |
| bp->link_params.loopback_mode = LOOPBACK_BMAC; |
| |
| bnx2x_phy_init(&bp->link_params, &bp->link_vars); |
| break; |
| case BNX2X_EXT_LOOPBACK: |
| if (bp->link_params.loopback_mode != LOOPBACK_EXT) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Can't configure external loopback\n"); |
| return -EINVAL; |
| } |
| break; |
| default: |
| DP(BNX2X_MSG_ETHTOOL, "Command parameters not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* prepare the loopback packet */ |
| pkt_size = (((bp->dev->mtu < ETH_MAX_PACKET_SIZE) ? |
| bp->dev->mtu : ETH_MAX_PACKET_SIZE) + ETH_HLEN); |
| skb = netdev_alloc_skb(bp->dev, fp_rx->rx_buf_size); |
| if (!skb) { |
| DP(BNX2X_MSG_ETHTOOL, "Can't allocate skb\n"); |
| rc = -ENOMEM; |
| goto test_loopback_exit; |
| } |
| packet = skb_put(skb, pkt_size); |
| memcpy(packet, bp->dev->dev_addr, ETH_ALEN); |
| eth_zero_addr(packet + ETH_ALEN); |
| memset(packet + 2*ETH_ALEN, 0x77, (ETH_HLEN - 2*ETH_ALEN)); |
| for (i = ETH_HLEN; i < pkt_size; i++) |
| packet[i] = (unsigned char) (i & 0xff); |
| mapping = dma_map_single(&bp->pdev->dev, skb->data, |
| skb_headlen(skb), DMA_TO_DEVICE); |
| if (unlikely(dma_mapping_error(&bp->pdev->dev, mapping))) { |
| rc = -ENOMEM; |
| dev_kfree_skb(skb); |
| DP(BNX2X_MSG_ETHTOOL, "Unable to map SKB\n"); |
| goto test_loopback_exit; |
| } |
| |
| /* send the loopback packet */ |
| num_pkts = 0; |
| tx_start_idx = le16_to_cpu(*txdata->tx_cons_sb); |
| rx_start_idx = le16_to_cpu(*fp_rx->rx_cons_sb); |
| |
| netdev_tx_sent_queue(txq, skb->len); |
| |
| pkt_prod = txdata->tx_pkt_prod++; |
| tx_buf = &txdata->tx_buf_ring[TX_BD(pkt_prod)]; |
| tx_buf->first_bd = txdata->tx_bd_prod; |
| tx_buf->skb = skb; |
| tx_buf->flags = 0; |
| |
| bd_prod = TX_BD(txdata->tx_bd_prod); |
| tx_start_bd = &txdata->tx_desc_ring[bd_prod].start_bd; |
| tx_start_bd->addr_hi = cpu_to_le32(U64_HI(mapping)); |
| tx_start_bd->addr_lo = cpu_to_le32(U64_LO(mapping)); |
| tx_start_bd->nbd = cpu_to_le16(2); /* start + pbd */ |
| tx_start_bd->nbytes = cpu_to_le16(skb_headlen(skb)); |
| tx_start_bd->vlan_or_ethertype = cpu_to_le16(pkt_prod); |
| tx_start_bd->bd_flags.as_bitfield = ETH_TX_BD_FLAGS_START_BD; |
| SET_FLAG(tx_start_bd->general_data, |
| ETH_TX_START_BD_HDR_NBDS, |
| 1); |
| SET_FLAG(tx_start_bd->general_data, |
| ETH_TX_START_BD_PARSE_NBDS, |
| 0); |
| |
| /* turn on parsing and get a BD */ |
| bd_prod = TX_BD(NEXT_TX_IDX(bd_prod)); |
| |
| if (CHIP_IS_E1x(bp)) { |
| u16 global_data = 0; |
| struct eth_tx_parse_bd_e1x *pbd_e1x = |
| &txdata->tx_desc_ring[bd_prod].parse_bd_e1x; |
| memset(pbd_e1x, 0, sizeof(struct eth_tx_parse_bd_e1x)); |
| SET_FLAG(global_data, |
| ETH_TX_PARSE_BD_E1X_ETH_ADDR_TYPE, UNICAST_ADDRESS); |
| pbd_e1x->global_data = cpu_to_le16(global_data); |
| } else { |
| u32 parsing_data = 0; |
| struct eth_tx_parse_bd_e2 *pbd_e2 = |
| &txdata->tx_desc_ring[bd_prod].parse_bd_e2; |
| memset(pbd_e2, 0, sizeof(struct eth_tx_parse_bd_e2)); |
| SET_FLAG(parsing_data, |
| ETH_TX_PARSE_BD_E2_ETH_ADDR_TYPE, UNICAST_ADDRESS); |
| pbd_e2->parsing_data = cpu_to_le32(parsing_data); |
| } |
| wmb(); |
| |
| txdata->tx_db.data.prod += 2; |
| barrier(); |
| DOORBELL(bp, txdata->cid, txdata->tx_db.raw); |
| |
| mmiowb(); |
| barrier(); |
| |
| num_pkts++; |
| txdata->tx_bd_prod += 2; /* start + pbd */ |
| |
| udelay(100); |
| |
| tx_idx = le16_to_cpu(*txdata->tx_cons_sb); |
| if (tx_idx != tx_start_idx + num_pkts) |
| goto test_loopback_exit; |
| |
| /* Unlike HC IGU won't generate an interrupt for status block |
| * updates that have been performed while interrupts were |
| * disabled. |
| */ |
| if (bp->common.int_block == INT_BLOCK_IGU) { |
| /* Disable local BHes to prevent a dead-lock situation between |
| * sch_direct_xmit() and bnx2x_run_loopback() (calling |
| * bnx2x_tx_int()), as both are taking netif_tx_lock(). |
| */ |
| local_bh_disable(); |
| bnx2x_tx_int(bp, txdata); |
| local_bh_enable(); |
| } |
| |
| rx_idx = le16_to_cpu(*fp_rx->rx_cons_sb); |
| if (rx_idx != rx_start_idx + num_pkts) |
| goto test_loopback_exit; |
| |
| cqe = &fp_rx->rx_comp_ring[RCQ_BD(fp_rx->rx_comp_cons)]; |
| cqe_fp_flags = cqe->fast_path_cqe.type_error_flags; |
| cqe_fp_type = cqe_fp_flags & ETH_FAST_PATH_RX_CQE_TYPE; |
| if (!CQE_TYPE_FAST(cqe_fp_type) || (cqe_fp_flags & ETH_RX_ERROR_FALGS)) |
| goto test_loopback_rx_exit; |
| |
| len = le16_to_cpu(cqe->fast_path_cqe.pkt_len_or_gro_seg_len); |
| if (len != pkt_size) |
| goto test_loopback_rx_exit; |
| |
| rx_buf = &fp_rx->rx_buf_ring[RX_BD(fp_rx->rx_bd_cons)]; |
| dma_sync_single_for_cpu(&bp->pdev->dev, |
| dma_unmap_addr(rx_buf, mapping), |
| fp_rx->rx_buf_size, DMA_FROM_DEVICE); |
| data = rx_buf->data + NET_SKB_PAD + cqe->fast_path_cqe.placement_offset; |
| for (i = ETH_HLEN; i < pkt_size; i++) |
| if (*(data + i) != (unsigned char) (i & 0xff)) |
| goto test_loopback_rx_exit; |
| |
| rc = 0; |
| |
| test_loopback_rx_exit: |
| |
| fp_rx->rx_bd_cons = NEXT_RX_IDX(fp_rx->rx_bd_cons); |
| fp_rx->rx_bd_prod = NEXT_RX_IDX(fp_rx->rx_bd_prod); |
| fp_rx->rx_comp_cons = NEXT_RCQ_IDX(fp_rx->rx_comp_cons); |
| fp_rx->rx_comp_prod = NEXT_RCQ_IDX(fp_rx->rx_comp_prod); |
| |
| /* Update producers */ |
| bnx2x_update_rx_prod(bp, fp_rx, fp_rx->rx_bd_prod, fp_rx->rx_comp_prod, |
| fp_rx->rx_sge_prod); |
| |
| test_loopback_exit: |
| bp->link_params.loopback_mode = LOOPBACK_NONE; |
| |
| return rc; |
| } |
| |
| static int bnx2x_test_loopback(struct bnx2x *bp) |
| { |
| int rc = 0, res; |
| |
| if (BP_NOMCP(bp)) |
| return rc; |
| |
| if (!netif_running(bp->dev)) |
| return BNX2X_LOOPBACK_FAILED; |
| |
| bnx2x_netif_stop(bp, 1); |
| bnx2x_acquire_phy_lock(bp); |
| |
| res = bnx2x_run_loopback(bp, BNX2X_PHY_LOOPBACK); |
| if (res) { |
| DP(BNX2X_MSG_ETHTOOL, " PHY loopback failed (res %d)\n", res); |
| rc |= BNX2X_PHY_LOOPBACK_FAILED; |
| } |
| |
| res = bnx2x_run_loopback(bp, BNX2X_MAC_LOOPBACK); |
| if (res) { |
| DP(BNX2X_MSG_ETHTOOL, " MAC loopback failed (res %d)\n", res); |
| rc |= BNX2X_MAC_LOOPBACK_FAILED; |
| } |
| |
| bnx2x_release_phy_lock(bp); |
| bnx2x_netif_start(bp); |
| |
| return rc; |
| } |
| |
| static int bnx2x_test_ext_loopback(struct bnx2x *bp) |
| { |
| int rc; |
| u8 is_serdes = |
| (bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) > 0; |
| |
| if (BP_NOMCP(bp)) |
| return -ENODEV; |
| |
| if (!netif_running(bp->dev)) |
| return BNX2X_EXT_LOOPBACK_FAILED; |
| |
| bnx2x_nic_unload(bp, UNLOAD_NORMAL, false); |
| rc = bnx2x_nic_load(bp, LOAD_LOOPBACK_EXT); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Can't perform self-test, nic_load (for external lb) failed\n"); |
| return -ENODEV; |
| } |
| bnx2x_wait_for_link(bp, 1, is_serdes); |
| |
| bnx2x_netif_stop(bp, 1); |
| |
| rc = bnx2x_run_loopback(bp, BNX2X_EXT_LOOPBACK); |
| if (rc) |
| DP(BNX2X_MSG_ETHTOOL, "EXT loopback failed (res %d)\n", rc); |
| |
| bnx2x_netif_start(bp); |
| |
| return rc; |
| } |
| |
| struct code_entry { |
| u32 sram_start_addr; |
| u32 code_attribute; |
| #define CODE_IMAGE_TYPE_MASK 0xf0800003 |
| #define CODE_IMAGE_VNTAG_PROFILES_DATA 0xd0000003 |
| #define CODE_IMAGE_LENGTH_MASK 0x007ffffc |
| #define CODE_IMAGE_TYPE_EXTENDED_DIR 0xe0000000 |
| u32 nvm_start_addr; |
| }; |
| |
| #define CODE_ENTRY_MAX 16 |
| #define CODE_ENTRY_EXTENDED_DIR_IDX 15 |
| #define MAX_IMAGES_IN_EXTENDED_DIR 64 |
| #define NVRAM_DIR_OFFSET 0x14 |
| |
| #define EXTENDED_DIR_EXISTS(code) \ |
| ((code & CODE_IMAGE_TYPE_MASK) == CODE_IMAGE_TYPE_EXTENDED_DIR && \ |
| (code & CODE_IMAGE_LENGTH_MASK) != 0) |
| |
| #define CRC32_RESIDUAL 0xdebb20e3 |
| #define CRC_BUFF_SIZE 256 |
| |
| static int bnx2x_nvram_crc(struct bnx2x *bp, |
| int offset, |
| int size, |
| u8 *buff) |
| { |
| u32 crc = ~0; |
| int rc = 0, done = 0; |
| |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "NVRAM CRC from 0x%08x to 0x%08x\n", offset, offset + size); |
| |
| while (done < size) { |
| int count = min_t(int, size - done, CRC_BUFF_SIZE); |
| |
| rc = bnx2x_nvram_read(bp, offset + done, buff, count); |
| |
| if (rc) |
| return rc; |
| |
| crc = crc32_le(crc, buff, count); |
| done += count; |
| } |
| |
| if (crc != CRC32_RESIDUAL) |
| rc = -EINVAL; |
| |
| return rc; |
| } |
| |
| static int bnx2x_test_nvram_dir(struct bnx2x *bp, |
| struct code_entry *entry, |
| u8 *buff) |
| { |
| size_t size = entry->code_attribute & CODE_IMAGE_LENGTH_MASK; |
| u32 type = entry->code_attribute & CODE_IMAGE_TYPE_MASK; |
| int rc; |
| |
| /* Zero-length images and AFEX profiles do not have CRC */ |
| if (size == 0 || type == CODE_IMAGE_VNTAG_PROFILES_DATA) |
| return 0; |
| |
| rc = bnx2x_nvram_crc(bp, entry->nvm_start_addr, size, buff); |
| if (rc) |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "image %x has failed crc test (rc %d)\n", type, rc); |
| |
| return rc; |
| } |
| |
| static int bnx2x_test_dir_entry(struct bnx2x *bp, u32 addr, u8 *buff) |
| { |
| int rc; |
| struct code_entry entry; |
| |
| rc = bnx2x_nvram_read32(bp, addr, (u32 *)&entry, sizeof(entry)); |
| if (rc) |
| return rc; |
| |
| return bnx2x_test_nvram_dir(bp, &entry, buff); |
| } |
| |
| static int bnx2x_test_nvram_ext_dirs(struct bnx2x *bp, u8 *buff) |
| { |
| u32 rc, cnt, dir_offset = NVRAM_DIR_OFFSET; |
| struct code_entry entry; |
| int i; |
| |
| rc = bnx2x_nvram_read32(bp, |
| dir_offset + |
| sizeof(entry) * CODE_ENTRY_EXTENDED_DIR_IDX, |
| (u32 *)&entry, sizeof(entry)); |
| if (rc) |
| return rc; |
| |
| if (!EXTENDED_DIR_EXISTS(entry.code_attribute)) |
| return 0; |
| |
| rc = bnx2x_nvram_read32(bp, entry.nvm_start_addr, |
| &cnt, sizeof(u32)); |
| if (rc) |
| return rc; |
| |
| dir_offset = entry.nvm_start_addr + 8; |
| |
| for (i = 0; i < cnt && i < MAX_IMAGES_IN_EXTENDED_DIR; i++) { |
| rc = bnx2x_test_dir_entry(bp, dir_offset + |
| sizeof(struct code_entry) * i, |
| buff); |
| if (rc) |
| return rc; |
| } |
| |
| return 0; |
| } |
| |
| static int bnx2x_test_nvram_dirs(struct bnx2x *bp, u8 *buff) |
| { |
| u32 rc, dir_offset = NVRAM_DIR_OFFSET; |
| int i; |
| |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, "NVRAM DIRS CRC test-set\n"); |
| |
| for (i = 0; i < CODE_ENTRY_EXTENDED_DIR_IDX; i++) { |
| rc = bnx2x_test_dir_entry(bp, dir_offset + |
| sizeof(struct code_entry) * i, |
| buff); |
| if (rc) |
| return rc; |
| } |
| |
| return bnx2x_test_nvram_ext_dirs(bp, buff); |
| } |
| |
| struct crc_pair { |
| int offset; |
| int size; |
| }; |
| |
| static int bnx2x_test_nvram_tbl(struct bnx2x *bp, |
| const struct crc_pair *nvram_tbl, u8 *buf) |
| { |
| int i; |
| |
| for (i = 0; nvram_tbl[i].size; i++) { |
| int rc = bnx2x_nvram_crc(bp, nvram_tbl[i].offset, |
| nvram_tbl[i].size, buf); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "nvram_tbl[%d] has failed crc test (rc %d)\n", |
| i, rc); |
| return rc; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int bnx2x_test_nvram(struct bnx2x *bp) |
| { |
| const struct crc_pair nvram_tbl[] = { |
| { 0, 0x14 }, /* bootstrap */ |
| { 0x14, 0xec }, /* dir */ |
| { 0x100, 0x350 }, /* manuf_info */ |
| { 0x450, 0xf0 }, /* feature_info */ |
| { 0x640, 0x64 }, /* upgrade_key_info */ |
| { 0x708, 0x70 }, /* manuf_key_info */ |
| { 0, 0 } |
| }; |
| const struct crc_pair nvram_tbl2[] = { |
| { 0x7e8, 0x350 }, /* manuf_info2 */ |
| { 0xb38, 0xf0 }, /* feature_info */ |
| { 0, 0 } |
| }; |
| |
| u8 *buf; |
| int rc; |
| u32 magic; |
| |
| if (BP_NOMCP(bp)) |
| return 0; |
| |
| buf = kmalloc(CRC_BUFF_SIZE, GFP_KERNEL); |
| if (!buf) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, "kmalloc failed\n"); |
| rc = -ENOMEM; |
| goto test_nvram_exit; |
| } |
| |
| rc = bnx2x_nvram_read32(bp, 0, &magic, sizeof(magic)); |
| if (rc) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "magic value read (rc %d)\n", rc); |
| goto test_nvram_exit; |
| } |
| |
| if (magic != 0x669955aa) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "wrong magic value (0x%08x)\n", magic); |
| rc = -ENODEV; |
| goto test_nvram_exit; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, "Port 0 CRC test-set\n"); |
| rc = bnx2x_test_nvram_tbl(bp, nvram_tbl, buf); |
| if (rc) |
| goto test_nvram_exit; |
| |
| if (!CHIP_IS_E1x(bp) && !CHIP_IS_57811xx(bp)) { |
| u32 hide = SHMEM_RD(bp, dev_info.shared_hw_config.config2) & |
| SHARED_HW_CFG_HIDE_PORT1; |
| |
| if (!hide) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "Port 1 CRC test-set\n"); |
| rc = bnx2x_test_nvram_tbl(bp, nvram_tbl2, buf); |
| if (rc) |
| goto test_nvram_exit; |
| } |
| } |
| |
| rc = bnx2x_test_nvram_dirs(bp, buf); |
| |
| test_nvram_exit: |
| kfree(buf); |
| return rc; |
| } |
| |
| /* Send an EMPTY ramrod on the first queue */ |
| static int bnx2x_test_intr(struct bnx2x *bp) |
| { |
| struct bnx2x_queue_state_params params = {NULL}; |
| |
| if (!netif_running(bp->dev)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -ENODEV; |
| } |
| |
| params.q_obj = &bp->sp_objs->q_obj; |
| params.cmd = BNX2X_Q_CMD_EMPTY; |
| |
| __set_bit(RAMROD_COMP_WAIT, ¶ms.ramrod_flags); |
| |
| return bnx2x_queue_state_change(bp, ¶ms); |
| } |
| |
| static void bnx2x_self_test(struct net_device *dev, |
| struct ethtool_test *etest, u64 *buf) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u8 is_serdes, link_up; |
| int rc, cnt = 0; |
| |
| if (pci_num_vf(bp->pdev)) { |
| DP(BNX2X_MSG_IOV, |
| "VFs are enabled, can not perform self test\n"); |
| return; |
| } |
| |
| if (bp->recovery_state != BNX2X_RECOVERY_DONE) { |
| netdev_err(bp->dev, |
| "Handling parity error recovery. Try again later\n"); |
| etest->flags |= ETH_TEST_FL_FAILED; |
| return; |
| } |
| |
| DP(BNX2X_MSG_ETHTOOL, |
| "Self-test command parameters: offline = %d, external_lb = %d\n", |
| (etest->flags & ETH_TEST_FL_OFFLINE), |
| (etest->flags & ETH_TEST_FL_EXTERNAL_LB)>>2); |
| |
| memset(buf, 0, sizeof(u64) * BNX2X_NUM_TESTS(bp)); |
| |
| if (bnx2x_test_nvram(bp) != 0) { |
| if (!IS_MF(bp)) |
| buf[4] = 1; |
| else |
| buf[0] = 1; |
| etest->flags |= ETH_TEST_FL_FAILED; |
| } |
| |
| if (!netif_running(dev)) { |
| DP(BNX2X_MSG_ETHTOOL, "Interface is down\n"); |
| return; |
| } |
| |
| is_serdes = (bp->link_vars.link_status & LINK_STATUS_SERDES_LINK) > 0; |
| link_up = bp->link_vars.link_up; |
| /* offline tests are not supported in MF mode */ |
| if ((etest->flags & ETH_TEST_FL_OFFLINE) && !IS_MF(bp)) { |
| int port = BP_PORT(bp); |
| u32 val; |
| |
| /* save current value of input enable for TX port IF */ |
| val = REG_RD(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4); |
| /* disable input for TX port IF */ |
| REG_WR(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4, 0); |
| |
| bnx2x_nic_unload(bp, UNLOAD_NORMAL, false); |
| rc = bnx2x_nic_load(bp, LOAD_DIAG); |
| if (rc) { |
| etest->flags |= ETH_TEST_FL_FAILED; |
| DP(BNX2X_MSG_ETHTOOL, |
| "Can't perform self-test, nic_load (for offline) failed\n"); |
| return; |
| } |
| |
| /* wait until link state is restored */ |
| bnx2x_wait_for_link(bp, 1, is_serdes); |
| |
| if (bnx2x_test_registers(bp) != 0) { |
| buf[0] = 1; |
| etest->flags |= ETH_TEST_FL_FAILED; |
| } |
| if (bnx2x_test_memory(bp) != 0) { |
| buf[1] = 1; |
| etest->flags |= ETH_TEST_FL_FAILED; |
| } |
| |
| buf[2] = bnx2x_test_loopback(bp); /* internal LB */ |
| if (buf[2] != 0) |
| etest->flags |= ETH_TEST_FL_FAILED; |
| |
| if (etest->flags & ETH_TEST_FL_EXTERNAL_LB) { |
| buf[3] = bnx2x_test_ext_loopback(bp); /* external LB */ |
| if (buf[3] != 0) |
| etest->flags |= ETH_TEST_FL_FAILED; |
| etest->flags |= ETH_TEST_FL_EXTERNAL_LB_DONE; |
| } |
| |
| bnx2x_nic_unload(bp, UNLOAD_NORMAL, false); |
| |
| /* restore input for TX port IF */ |
| REG_WR(bp, NIG_REG_EGRESS_UMP0_IN_EN + port*4, val); |
| rc = bnx2x_nic_load(bp, LOAD_NORMAL); |
| if (rc) { |
| etest->flags |= ETH_TEST_FL_FAILED; |
| DP(BNX2X_MSG_ETHTOOL, |
| "Can't perform self-test, nic_load (for online) failed\n"); |
| return; |
| } |
| /* wait until link state is restored */ |
| bnx2x_wait_for_link(bp, link_up, is_serdes); |
| } |
| |
| if (bnx2x_test_intr(bp) != 0) { |
| if (!IS_MF(bp)) |
| buf[5] = 1; |
| else |
| buf[1] = 1; |
| etest->flags |= ETH_TEST_FL_FAILED; |
| } |
| |
| if (link_up) { |
| cnt = 100; |
| while (bnx2x_link_test(bp, is_serdes) && --cnt) |
| msleep(20); |
| } |
| |
| if (!cnt) { |
| if (!IS_MF(bp)) |
| buf[6] = 1; |
| else |
| buf[2] = 1; |
| etest->flags |= ETH_TEST_FL_FAILED; |
| } |
| } |
| |
| #define IS_PORT_STAT(i) (bnx2x_stats_arr[i].is_port_stat) |
| #define HIDE_PORT_STAT(bp) IS_VF(bp) |
| |
| /* ethtool statistics are displayed for all regular ethernet queues and the |
| * fcoe L2 queue if not disabled |
| */ |
| static int bnx2x_num_stat_queues(struct bnx2x *bp) |
| { |
| return BNX2X_NUM_ETH_QUEUES(bp); |
| } |
| |
| static int bnx2x_get_sset_count(struct net_device *dev, int stringset) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int i, num_strings = 0; |
| |
| switch (stringset) { |
| case ETH_SS_STATS: |
| if (is_multi(bp)) { |
| num_strings = bnx2x_num_stat_queues(bp) * |
| BNX2X_NUM_Q_STATS; |
| } else |
| num_strings = 0; |
| if (HIDE_PORT_STAT(bp)) { |
| for (i = 0; i < BNX2X_NUM_STATS; i++) |
| if (!IS_PORT_STAT(i)) |
| num_strings++; |
| } else |
| num_strings += BNX2X_NUM_STATS; |
| |
| return num_strings; |
| |
| case ETH_SS_TEST: |
| return BNX2X_NUM_TESTS(bp); |
| |
| case ETH_SS_PRIV_FLAGS: |
| return BNX2X_PRI_FLAG_LEN; |
| |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static u32 bnx2x_get_private_flags(struct net_device *dev) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 flags = 0; |
| |
| flags |= (!(bp->flags & NO_ISCSI_FLAG) ? 1 : 0) << BNX2X_PRI_FLAG_ISCSI; |
| flags |= (!(bp->flags & NO_FCOE_FLAG) ? 1 : 0) << BNX2X_PRI_FLAG_FCOE; |
| flags |= (!!IS_MF_STORAGE_ONLY(bp)) << BNX2X_PRI_FLAG_STORAGE; |
| |
| return flags; |
| } |
| |
| static void bnx2x_get_strings(struct net_device *dev, u32 stringset, u8 *buf) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| int i, j, k, start; |
| char queue_name[MAX_QUEUE_NAME_LEN+1]; |
| |
| switch (stringset) { |
| case ETH_SS_STATS: |
| k = 0; |
| if (is_multi(bp)) { |
| for_each_eth_queue(bp, i) { |
| memset(queue_name, 0, sizeof(queue_name)); |
| sprintf(queue_name, "%d", i); |
| for (j = 0; j < BNX2X_NUM_Q_STATS; j++) |
| snprintf(buf + (k + j)*ETH_GSTRING_LEN, |
| ETH_GSTRING_LEN, |
| bnx2x_q_stats_arr[j].string, |
| queue_name); |
| k += BNX2X_NUM_Q_STATS; |
| } |
| } |
| |
| for (i = 0, j = 0; i < BNX2X_NUM_STATS; i++) { |
| if (HIDE_PORT_STAT(bp) && IS_PORT_STAT(i)) |
| continue; |
| strcpy(buf + (k + j)*ETH_GSTRING_LEN, |
| bnx2x_stats_arr[i].string); |
| j++; |
| } |
| |
| break; |
| |
| case ETH_SS_TEST: |
| /* First 4 tests cannot be done in MF mode */ |
| if (!IS_MF(bp)) |
| start = 0; |
| else |
| start = 4; |
| memcpy(buf, bnx2x_tests_str_arr + start, |
| ETH_GSTRING_LEN * BNX2X_NUM_TESTS(bp)); |
| break; |
| |
| case ETH_SS_PRIV_FLAGS: |
| memcpy(buf, bnx2x_private_arr, |
| ETH_GSTRING_LEN * BNX2X_PRI_FLAG_LEN); |
| break; |
| } |
| } |
| |
| static void bnx2x_get_ethtool_stats(struct net_device *dev, |
| struct ethtool_stats *stats, u64 *buf) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u32 *hw_stats, *offset; |
| int i, j, k = 0; |
| |
| if (is_multi(bp)) { |
| for_each_eth_queue(bp, i) { |
| hw_stats = (u32 *)&bp->fp_stats[i].eth_q_stats; |
| for (j = 0; j < BNX2X_NUM_Q_STATS; j++) { |
| if (bnx2x_q_stats_arr[j].size == 0) { |
| /* skip this counter */ |
| buf[k + j] = 0; |
| continue; |
| } |
| offset = (hw_stats + |
| bnx2x_q_stats_arr[j].offset); |
| if (bnx2x_q_stats_arr[j].size == 4) { |
| /* 4-byte counter */ |
| buf[k + j] = (u64) *offset; |
| continue; |
| } |
| /* 8-byte counter */ |
| buf[k + j] = HILO_U64(*offset, *(offset + 1)); |
| } |
| k += BNX2X_NUM_Q_STATS; |
| } |
| } |
| |
| hw_stats = (u32 *)&bp->eth_stats; |
| for (i = 0, j = 0; i < BNX2X_NUM_STATS; i++) { |
| if (HIDE_PORT_STAT(bp) && IS_PORT_STAT(i)) |
| continue; |
| if (bnx2x_stats_arr[i].size == 0) { |
| /* skip this counter */ |
| buf[k + j] = 0; |
| j++; |
| continue; |
| } |
| offset = (hw_stats + bnx2x_stats_arr[i].offset); |
| if (bnx2x_stats_arr[i].size == 4) { |
| /* 4-byte counter */ |
| buf[k + j] = (u64) *offset; |
| j++; |
| continue; |
| } |
| /* 8-byte counter */ |
| buf[k + j] = HILO_U64(*offset, *(offset + 1)); |
| j++; |
| } |
| } |
| |
| static int bnx2x_set_phys_id(struct net_device *dev, |
| enum ethtool_phys_id_state state) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (!bnx2x_is_nvm_accessible(bp)) { |
| DP(BNX2X_MSG_ETHTOOL | BNX2X_MSG_NVM, |
| "cannot access eeprom when the interface is down\n"); |
| return -EAGAIN; |
| } |
| |
| switch (state) { |
| case ETHTOOL_ID_ACTIVE: |
| return 1; /* cycle on/off once per second */ |
| |
| case ETHTOOL_ID_ON: |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_set_led(&bp->link_params, &bp->link_vars, |
| LED_MODE_ON, SPEED_1000); |
| bnx2x_release_phy_lock(bp); |
| break; |
| |
| case ETHTOOL_ID_OFF: |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_set_led(&bp->link_params, &bp->link_vars, |
| LED_MODE_FRONT_PANEL_OFF, 0); |
| bnx2x_release_phy_lock(bp); |
| break; |
| |
| case ETHTOOL_ID_INACTIVE: |
| bnx2x_acquire_phy_lock(bp); |
| bnx2x_set_led(&bp->link_params, &bp->link_vars, |
| LED_MODE_OPER, |
| bp->link_vars.line_speed); |
| bnx2x_release_phy_lock(bp); |
| } |
| |
| return 0; |
| } |
| |
| static int bnx2x_get_rss_flags(struct bnx2x *bp, struct ethtool_rxnfc *info) |
| { |
| switch (info->flow_type) { |
| case TCP_V4_FLOW: |
| case TCP_V6_FLOW: |
| info->data = RXH_IP_SRC | RXH_IP_DST | |
| RXH_L4_B_0_1 | RXH_L4_B_2_3; |
| break; |
| case UDP_V4_FLOW: |
| if (bp->rss_conf_obj.udp_rss_v4) |
| info->data = RXH_IP_SRC | RXH_IP_DST | |
| RXH_L4_B_0_1 | RXH_L4_B_2_3; |
| else |
| info->data = RXH_IP_SRC | RXH_IP_DST; |
| break; |
| case UDP_V6_FLOW: |
| if (bp->rss_conf_obj.udp_rss_v6) |
| info->data = RXH_IP_SRC | RXH_IP_DST | |
| RXH_L4_B_0_1 | RXH_L4_B_2_3; |
| else |
| info->data = RXH_IP_SRC | RXH_IP_DST; |
| break; |
| case IPV4_FLOW: |
| case IPV6_FLOW: |
| info->data = RXH_IP_SRC | RXH_IP_DST; |
| break; |
| default: |
| info->data = 0; |
| break; |
| } |
| |
| return 0; |
| } |
| |
| static int bnx2x_get_rxnfc(struct net_device *dev, struct ethtool_rxnfc *info, |
| u32 *rules __always_unused) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| switch (info->cmd) { |
| case ETHTOOL_GRXRINGS: |
| info->data = BNX2X_NUM_ETH_QUEUES(bp); |
| return 0; |
| case ETHTOOL_GRXFH: |
| return bnx2x_get_rss_flags(bp, info); |
| default: |
| DP(BNX2X_MSG_ETHTOOL, "Command parameters not supported\n"); |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int bnx2x_set_rss_flags(struct bnx2x *bp, struct ethtool_rxnfc *info) |
| { |
| int udp_rss_requested; |
| |
| DP(BNX2X_MSG_ETHTOOL, |
| "Set rss flags command parameters: flow type = %d, data = %llu\n", |
| info->flow_type, info->data); |
| |
| switch (info->flow_type) { |
| case TCP_V4_FLOW: |
| case TCP_V6_FLOW: |
| /* For TCP only 4-tupple hash is supported */ |
| if (info->data ^ (RXH_IP_SRC | RXH_IP_DST | |
| RXH_L4_B_0_1 | RXH_L4_B_2_3)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Command parameters not supported\n"); |
| return -EINVAL; |
| } |
| return 0; |
| |
| case UDP_V4_FLOW: |
| case UDP_V6_FLOW: |
| /* For UDP either 2-tupple hash or 4-tupple hash is supported */ |
| if (info->data == (RXH_IP_SRC | RXH_IP_DST | |
| RXH_L4_B_0_1 | RXH_L4_B_2_3)) |
| udp_rss_requested = 1; |
| else if (info->data == (RXH_IP_SRC | RXH_IP_DST)) |
| udp_rss_requested = 0; |
| else |
| return -EINVAL; |
| |
| if (CHIP_IS_E1x(bp) && udp_rss_requested) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "57710, 57711 boards don't support RSS according to UDP 4-tuple\n"); |
| return -EINVAL; |
| } |
| |
| if ((info->flow_type == UDP_V4_FLOW) && |
| (bp->rss_conf_obj.udp_rss_v4 != udp_rss_requested)) { |
| bp->rss_conf_obj.udp_rss_v4 = udp_rss_requested; |
| DP(BNX2X_MSG_ETHTOOL, |
| "rss re-configured, UDP 4-tupple %s\n", |
| udp_rss_requested ? "enabled" : "disabled"); |
| return bnx2x_rss(bp, &bp->rss_conf_obj, false, true); |
| } else if ((info->flow_type == UDP_V6_FLOW) && |
| (bp->rss_conf_obj.udp_rss_v6 != udp_rss_requested)) { |
| bp->rss_conf_obj.udp_rss_v6 = udp_rss_requested; |
| DP(BNX2X_MSG_ETHTOOL, |
| "rss re-configured, UDP 4-tupple %s\n", |
| udp_rss_requested ? "enabled" : "disabled"); |
| return bnx2x_rss(bp, &bp->rss_conf_obj, false, true); |
| } |
| return 0; |
| |
| case IPV4_FLOW: |
| case IPV6_FLOW: |
| /* For IP only 2-tupple hash is supported */ |
| if (info->data ^ (RXH_IP_SRC | RXH_IP_DST)) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Command parameters not supported\n"); |
| return -EINVAL; |
| } |
| return 0; |
| |
| case SCTP_V4_FLOW: |
| case AH_ESP_V4_FLOW: |
| case AH_V4_FLOW: |
| case ESP_V4_FLOW: |
| case SCTP_V6_FLOW: |
| case AH_ESP_V6_FLOW: |
| case AH_V6_FLOW: |
| case ESP_V6_FLOW: |
| case IP_USER_FLOW: |
| case ETHER_FLOW: |
| /* RSS is not supported for these protocols */ |
| if (info->data) { |
| DP(BNX2X_MSG_ETHTOOL, |
| "Command parameters not supported\n"); |
| return -EINVAL; |
| } |
| return 0; |
| |
| default: |
| return -EINVAL; |
| } |
| } |
| |
| static int bnx2x_set_rxnfc(struct net_device *dev, struct ethtool_rxnfc *info) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| switch (info->cmd) { |
| case ETHTOOL_SRXFH: |
| return bnx2x_set_rss_flags(bp, info); |
| default: |
| DP(BNX2X_MSG_ETHTOOL, "Command parameters not supported\n"); |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static u32 bnx2x_get_rxfh_indir_size(struct net_device *dev) |
| { |
| return T_ETH_INDIRECTION_TABLE_SIZE; |
| } |
| |
| static int bnx2x_get_rxfh(struct net_device *dev, u32 *indir, u8 *key, |
| u8 *hfunc) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| u8 ind_table[T_ETH_INDIRECTION_TABLE_SIZE] = {0}; |
| size_t i; |
| |
| if (hfunc) |
| *hfunc = ETH_RSS_HASH_TOP; |
| if (!indir) |
| return 0; |
| |
| /* Get the current configuration of the RSS indirection table */ |
| bnx2x_get_rss_ind_table(&bp->rss_conf_obj, ind_table); |
| |
| /* |
| * We can't use a memcpy() as an internal storage of an |
| * indirection table is a u8 array while indir->ring_index |
| * points to an array of u32. |
| * |
| * Indirection table contains the FW Client IDs, so we need to |
| * align the returned table to the Client ID of the leading RSS |
| * queue. |
| */ |
| for (i = 0; i < T_ETH_INDIRECTION_TABLE_SIZE; i++) |
| indir[i] = ind_table[i] - bp->fp->cl_id; |
| |
| return 0; |
| } |
| |
| static int bnx2x_set_rxfh(struct net_device *dev, const u32 *indir, |
| const u8 *key, const u8 hfunc) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| size_t i; |
| |
| /* We require at least one supported parameter to be changed and no |
| * change in any of the unsupported parameters |
| */ |
| if (key || |
| (hfunc != ETH_RSS_HASH_NO_CHANGE && hfunc != ETH_RSS_HASH_TOP)) |
| return -EOPNOTSUPP; |
| |
| if (!indir) |
| return 0; |
| |
| for (i = 0; i < T_ETH_INDIRECTION_TABLE_SIZE; i++) { |
| /* |
| * The same as in bnx2x_get_rxfh: we can't use a memcpy() |
| * as an internal storage of an indirection table is a u8 array |
| * while indir->ring_index points to an array of u32. |
| * |
| * Indirection table contains the FW Client IDs, so we need to |
| * align the received table to the Client ID of the leading RSS |
| * queue |
| */ |
| bp->rss_conf_obj.ind_table[i] = indir[i] + bp->fp->cl_id; |
| } |
| |
| return bnx2x_config_rss_eth(bp, false); |
| } |
| |
| /** |
| * bnx2x_get_channels - gets the number of RSS queues. |
| * |
| * @dev: net device |
| * @channels: returns the number of max / current queues |
| */ |
| static void bnx2x_get_channels(struct net_device *dev, |
| struct ethtool_channels *channels) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| channels->max_combined = BNX2X_MAX_RSS_COUNT(bp); |
| channels->combined_count = BNX2X_NUM_ETH_QUEUES(bp); |
| } |
| |
| /** |
| * bnx2x_change_num_queues - change the number of RSS queues. |
| * |
| * @bp: bnx2x private structure |
| * |
| * Re-configure interrupt mode to get the new number of MSI-X |
| * vectors and re-add NAPI objects. |
| */ |
| static void bnx2x_change_num_queues(struct bnx2x *bp, int num_rss) |
| { |
| bnx2x_disable_msi(bp); |
| bp->num_ethernet_queues = num_rss; |
| bp->num_queues = bp->num_ethernet_queues + bp->num_cnic_queues; |
| BNX2X_DEV_INFO("set number of queues to %d\n", bp->num_queues); |
| bnx2x_set_int_mode(bp); |
| } |
| |
| /** |
| * bnx2x_set_channels - sets the number of RSS queues. |
| * |
| * @dev: net device |
| * @channels: includes the number of queues requested |
| */ |
| static int bnx2x_set_channels(struct net_device *dev, |
| struct ethtool_channels *channels) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| DP(BNX2X_MSG_ETHTOOL, |
| "set-channels command parameters: rx = %d, tx = %d, other = %d, combined = %d\n", |
| channels->rx_count, channels->tx_count, channels->other_count, |
| channels->combined_count); |
| |
| if (pci_num_vf(bp->pdev)) { |
| DP(BNX2X_MSG_IOV, "VFs are enabled, can not set channels\n"); |
| return -EPERM; |
| } |
| |
| /* We don't support separate rx / tx channels. |
| * We don't allow setting 'other' channels. |
| */ |
| if (channels->rx_count || channels->tx_count || channels->other_count |
| || (channels->combined_count == 0) || |
| (channels->combined_count > BNX2X_MAX_RSS_COUNT(bp))) { |
| DP(BNX2X_MSG_ETHTOOL, "command parameters not supported\n"); |
| return -EINVAL; |
| } |
| |
| /* Check if there was a change in the active parameters */ |
| if (channels->combined_count == BNX2X_NUM_ETH_QUEUES(bp)) { |
| DP(BNX2X_MSG_ETHTOOL, "No change in active parameters\n"); |
| return 0; |
| } |
| |
| /* Set the requested number of queues in bp context. |
| * Note that the actual number of queues created during load may be |
| * less than requested if memory is low. |
| */ |
| if (unlikely(!netif_running(dev))) { |
| bnx2x_change_num_queues(bp, channels->combined_count); |
| return 0; |
| } |
| bnx2x_nic_unload(bp, UNLOAD_NORMAL, true); |
| bnx2x_change_num_queues(bp, channels->combined_count); |
| return bnx2x_nic_load(bp, LOAD_NORMAL); |
| } |
| |
| static int bnx2x_get_ts_info(struct net_device *dev, |
| struct ethtool_ts_info *info) |
| { |
| struct bnx2x *bp = netdev_priv(dev); |
| |
| if (bp->flags & PTP_SUPPORTED) { |
| info->so_timestamping = SOF_TIMESTAMPING_TX_SOFTWARE | |
| SOF_TIMESTAMPING_RX_SOFTWARE | |
| SOF_TIMESTAMPING_SOFTWARE | |
| SOF_TIMESTAMPING_TX_HARDWARE | |
| SOF_TIMESTAMPING_RX_HARDWARE | |
| SOF_TIMESTAMPING_RAW_HARDWARE; |
| |
| if (bp->ptp_clock) |
| info->phc_index = ptp_clock_index(bp->ptp_clock); |
| else |
| info->phc_index = -1; |
| |
| info->rx_filters = (1 << HWTSTAMP_FILTER_NONE) | |
| (1 << HWTSTAMP_FILTER_PTP_V1_L4_EVENT) | |
| (1 << HWTSTAMP_FILTER_PTP_V2_L4_EVENT) | |
| (1 << HWTSTAMP_FILTER_PTP_V2_EVENT); |
| |
| info->tx_types = (1 << HWTSTAMP_TX_OFF)|(1 << HWTSTAMP_TX_ON); |
| |
| return 0; |
| } |
| |
| return ethtool_op_get_ts_info(dev, info); |
| } |
| |
| static const struct ethtool_ops bnx2x_ethtool_ops = { |
| .get_drvinfo = bnx2x_get_drvinfo, |
| .get_regs_len = bnx2x_get_regs_len, |
| .get_regs = bnx2x_get_regs, |
| .get_dump_flag = bnx2x_get_dump_flag, |
| .get_dump_data = bnx2x_get_dump_data, |
| .set_dump = bnx2x_set_dump, |
| .get_wol = bnx2x_get_wol, |
| .set_wol = bnx2x_set_wol, |
| .get_msglevel = bnx2x_get_msglevel, |
| .set_msglevel = bnx2x_set_msglevel, |
| .nway_reset = bnx2x_nway_reset, |
| .get_link = bnx2x_get_link, |
| .get_eeprom_len = bnx2x_get_eeprom_len, |
| .get_eeprom = bnx2x_get_eeprom, |
| .set_eeprom = bnx2x_set_eeprom, |
| .get_coalesce = bnx2x_get_coalesce, |
| .set_coalesce = bnx2x_set_coalesce, |
| .get_ringparam = bnx2x_get_ringparam, |
| .set_ringparam = bnx2x_set_ringparam, |
| .get_pauseparam = bnx2x_get_pauseparam, |
| .set_pauseparam = bnx2x_set_pauseparam, |
| .self_test = bnx2x_self_test, |
| .get_sset_count = bnx2x_get_sset_count, |
| .get_priv_flags = bnx2x_get_private_flags, |
| .get_strings = bnx2x_get_strings, |
| .set_phys_id = bnx2x_set_phys_id, |
| .get_ethtool_stats = bnx2x_get_ethtool_stats, |
| .get_rxnfc = bnx2x_get_rxnfc, |
| .set_rxnfc = bnx2x_set_rxnfc, |
| .get_rxfh_indir_size = bnx2x_get_rxfh_indir_size, |
| .get_rxfh = bnx2x_get_rxfh, |
| .set_rxfh = bnx2x_set_rxfh, |
| .get_channels = bnx2x_get_channels, |
| .set_channels = bnx2x_set_channels, |
| .get_module_info = bnx2x_get_module_info, |
| .get_module_eeprom = bnx2x_get_module_eeprom, |
| .get_eee = bnx2x_get_eee, |
| .set_eee = bnx2x_set_eee, |
| .get_ts_info = bnx2x_get_ts_info, |
| .get_link_ksettings = bnx2x_get_link_ksettings, |
| .set_link_ksettings = bnx2x_set_link_ksettings, |
| }; |
| |
| static const struct ethtool_ops bnx2x_vf_ethtool_ops = { |
| .get_drvinfo = bnx2x_get_drvinfo, |
| .get_msglevel = bnx2x_get_msglevel, |
| .set_msglevel = bnx2x_set_msglevel, |
| .get_link = bnx2x_get_link, |
| .get_coalesce = bnx2x_get_coalesce, |
| .get_ringparam = bnx2x_get_ringparam, |
| .set_ringparam = bnx2x_set_ringparam, |
| .get_sset_count = bnx2x_get_sset_count, |
| .get_strings = bnx2x_get_strings, |
| .get_ethtool_stats = bnx2x_get_ethtool_stats, |
| .get_rxnfc = bnx2x_get_rxnfc, |
| .set_rxnfc = bnx2x_set_rxnfc, |
| .get_rxfh_indir_size = bnx2x_get_rxfh_indir_size, |
| .get_rxfh = bnx2x_get_rxfh, |
| .set_rxfh = bnx2x_set_rxfh, |
| .get_channels = bnx2x_get_channels, |
| .set_channels = bnx2x_set_channels, |
| .get_link_ksettings = bnx2x_get_vf_link_ksettings, |
| }; |
| |
| void bnx2x_set_ethtool_ops(struct bnx2x *bp, struct net_device *netdev) |
| { |
| netdev->ethtool_ops = (IS_PF(bp)) ? |
| &bnx2x_ethtool_ops : &bnx2x_vf_ethtool_ops; |
| } |