| // SPDX-License-Identifier: GPL-2.0 |
| |
| /* Texas Instruments ICSSG Ethernet Driver |
| * |
| * Copyright (C) 2018-2022 Texas Instruments Incorporated - https://www.ti.com/ |
| * |
| */ |
| |
| #include <linux/bitops.h> |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/dma-mapping.h> |
| #include <linux/dma/ti-cppi5.h> |
| #include <linux/etherdevice.h> |
| #include <linux/genalloc.h> |
| #include <linux/if_vlan.h> |
| #include <linux/interrupt.h> |
| #include <linux/kernel.h> |
| #include <linux/mfd/syscon.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_mdio.h> |
| #include <linux/of_net.h> |
| #include <linux/platform_device.h> |
| #include <linux/phy.h> |
| #include <linux/property.h> |
| #include <linux/remoteproc/pruss.h> |
| #include <linux/regmap.h> |
| #include <linux/remoteproc.h> |
| |
| #include "icssg_prueth.h" |
| #include "icssg_mii_rt.h" |
| #include "../k3-cppi-desc-pool.h" |
| |
| #define PRUETH_MODULE_DESCRIPTION "PRUSS ICSSG Ethernet driver" |
| |
| /* Netif debug messages possible */ |
| #define PRUETH_EMAC_DEBUG (NETIF_MSG_DRV | \ |
| NETIF_MSG_PROBE | \ |
| NETIF_MSG_LINK | \ |
| NETIF_MSG_TIMER | \ |
| NETIF_MSG_IFDOWN | \ |
| NETIF_MSG_IFUP | \ |
| NETIF_MSG_RX_ERR | \ |
| NETIF_MSG_TX_ERR | \ |
| NETIF_MSG_TX_QUEUED | \ |
| NETIF_MSG_INTR | \ |
| NETIF_MSG_TX_DONE | \ |
| NETIF_MSG_RX_STATUS | \ |
| NETIF_MSG_PKTDATA | \ |
| NETIF_MSG_HW | \ |
| NETIF_MSG_WOL) |
| |
| #define prueth_napi_to_emac(napi) container_of(napi, struct prueth_emac, napi_rx) |
| |
| /* CTRLMMR_ICSSG_RGMII_CTRL register bits */ |
| #define ICSSG_CTRL_RGMII_ID_MODE BIT(24) |
| |
| #define IEP_DEFAULT_CYCLE_TIME_NS 1000000 /* 1 ms */ |
| |
| static void prueth_cleanup_rx_chns(struct prueth_emac *emac, |
| struct prueth_rx_chn *rx_chn, |
| int max_rflows) |
| { |
| if (rx_chn->desc_pool) |
| k3_cppi_desc_pool_destroy(rx_chn->desc_pool); |
| |
| if (rx_chn->rx_chn) |
| k3_udma_glue_release_rx_chn(rx_chn->rx_chn); |
| } |
| |
| static void prueth_cleanup_tx_chns(struct prueth_emac *emac) |
| { |
| int i; |
| |
| for (i = 0; i < emac->tx_ch_num; i++) { |
| struct prueth_tx_chn *tx_chn = &emac->tx_chns[i]; |
| |
| if (tx_chn->desc_pool) |
| k3_cppi_desc_pool_destroy(tx_chn->desc_pool); |
| |
| if (tx_chn->tx_chn) |
| k3_udma_glue_release_tx_chn(tx_chn->tx_chn); |
| |
| /* Assume prueth_cleanup_tx_chns() is called at the |
| * end after all channel resources are freed |
| */ |
| memset(tx_chn, 0, sizeof(*tx_chn)); |
| } |
| } |
| |
| static void prueth_ndev_del_tx_napi(struct prueth_emac *emac, int num) |
| { |
| int i; |
| |
| for (i = 0; i < num; i++) { |
| struct prueth_tx_chn *tx_chn = &emac->tx_chns[i]; |
| |
| if (tx_chn->irq) |
| free_irq(tx_chn->irq, tx_chn); |
| netif_napi_del(&tx_chn->napi_tx); |
| } |
| } |
| |
| static void prueth_xmit_free(struct prueth_tx_chn *tx_chn, |
| struct cppi5_host_desc_t *desc) |
| { |
| struct cppi5_host_desc_t *first_desc, *next_desc; |
| dma_addr_t buf_dma, next_desc_dma; |
| u32 buf_dma_len; |
| |
| first_desc = desc; |
| next_desc = first_desc; |
| |
| cppi5_hdesc_get_obuf(first_desc, &buf_dma, &buf_dma_len); |
| k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &buf_dma); |
| |
| dma_unmap_single(tx_chn->dma_dev, buf_dma, buf_dma_len, |
| DMA_TO_DEVICE); |
| |
| next_desc_dma = cppi5_hdesc_get_next_hbdesc(first_desc); |
| k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &next_desc_dma); |
| while (next_desc_dma) { |
| next_desc = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool, |
| next_desc_dma); |
| cppi5_hdesc_get_obuf(next_desc, &buf_dma, &buf_dma_len); |
| k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &buf_dma); |
| |
| dma_unmap_page(tx_chn->dma_dev, buf_dma, buf_dma_len, |
| DMA_TO_DEVICE); |
| |
| next_desc_dma = cppi5_hdesc_get_next_hbdesc(next_desc); |
| k3_udma_glue_tx_cppi5_to_dma_addr(tx_chn->tx_chn, &next_desc_dma); |
| |
| k3_cppi_desc_pool_free(tx_chn->desc_pool, next_desc); |
| } |
| |
| k3_cppi_desc_pool_free(tx_chn->desc_pool, first_desc); |
| } |
| |
| static int emac_tx_complete_packets(struct prueth_emac *emac, int chn, |
| int budget) |
| { |
| struct net_device *ndev = emac->ndev; |
| struct cppi5_host_desc_t *desc_tx; |
| struct netdev_queue *netif_txq; |
| struct prueth_tx_chn *tx_chn; |
| unsigned int total_bytes = 0; |
| struct sk_buff *skb; |
| dma_addr_t desc_dma; |
| int res, num_tx = 0; |
| void **swdata; |
| |
| tx_chn = &emac->tx_chns[chn]; |
| |
| while (true) { |
| res = k3_udma_glue_pop_tx_chn(tx_chn->tx_chn, &desc_dma); |
| if (res == -ENODATA) |
| break; |
| |
| /* teardown completion */ |
| if (cppi5_desc_is_tdcm(desc_dma)) { |
| if (atomic_dec_and_test(&emac->tdown_cnt)) |
| complete(&emac->tdown_complete); |
| break; |
| } |
| |
| desc_tx = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool, |
| desc_dma); |
| swdata = cppi5_hdesc_get_swdata(desc_tx); |
| |
| skb = *(swdata); |
| prueth_xmit_free(tx_chn, desc_tx); |
| |
| ndev = skb->dev; |
| ndev->stats.tx_packets++; |
| ndev->stats.tx_bytes += skb->len; |
| total_bytes += skb->len; |
| napi_consume_skb(skb, budget); |
| num_tx++; |
| } |
| |
| if (!num_tx) |
| return 0; |
| |
| netif_txq = netdev_get_tx_queue(ndev, chn); |
| netdev_tx_completed_queue(netif_txq, num_tx, total_bytes); |
| |
| if (netif_tx_queue_stopped(netif_txq)) { |
| /* If the TX queue was stopped, wake it now |
| * if we have enough room. |
| */ |
| __netif_tx_lock(netif_txq, smp_processor_id()); |
| if (netif_running(ndev) && |
| (k3_cppi_desc_pool_avail(tx_chn->desc_pool) >= |
| MAX_SKB_FRAGS)) |
| netif_tx_wake_queue(netif_txq); |
| __netif_tx_unlock(netif_txq); |
| } |
| |
| return num_tx; |
| } |
| |
| static int emac_napi_tx_poll(struct napi_struct *napi_tx, int budget) |
| { |
| struct prueth_tx_chn *tx_chn = prueth_napi_to_tx_chn(napi_tx); |
| struct prueth_emac *emac = tx_chn->emac; |
| int num_tx_packets; |
| |
| num_tx_packets = emac_tx_complete_packets(emac, tx_chn->id, budget); |
| |
| if (num_tx_packets >= budget) |
| return budget; |
| |
| if (napi_complete_done(napi_tx, num_tx_packets)) |
| enable_irq(tx_chn->irq); |
| |
| return num_tx_packets; |
| } |
| |
| static irqreturn_t prueth_tx_irq(int irq, void *dev_id) |
| { |
| struct prueth_tx_chn *tx_chn = dev_id; |
| |
| disable_irq_nosync(irq); |
| napi_schedule(&tx_chn->napi_tx); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static int prueth_ndev_add_tx_napi(struct prueth_emac *emac) |
| { |
| struct prueth *prueth = emac->prueth; |
| int i, ret; |
| |
| for (i = 0; i < emac->tx_ch_num; i++) { |
| struct prueth_tx_chn *tx_chn = &emac->tx_chns[i]; |
| |
| netif_napi_add_tx(emac->ndev, &tx_chn->napi_tx, emac_napi_tx_poll); |
| ret = request_irq(tx_chn->irq, prueth_tx_irq, |
| IRQF_TRIGGER_HIGH, tx_chn->name, |
| tx_chn); |
| if (ret) { |
| netif_napi_del(&tx_chn->napi_tx); |
| dev_err(prueth->dev, "unable to request TX IRQ %d\n", |
| tx_chn->irq); |
| goto fail; |
| } |
| } |
| |
| return 0; |
| fail: |
| prueth_ndev_del_tx_napi(emac, i); |
| return ret; |
| } |
| |
| static int prueth_init_tx_chns(struct prueth_emac *emac) |
| { |
| static const struct k3_ring_cfg ring_cfg = { |
| .elm_size = K3_RINGACC_RING_ELSIZE_8, |
| .mode = K3_RINGACC_RING_MODE_RING, |
| .flags = 0, |
| .size = PRUETH_MAX_TX_DESC, |
| }; |
| struct k3_udma_glue_tx_channel_cfg tx_cfg; |
| struct device *dev = emac->prueth->dev; |
| struct net_device *ndev = emac->ndev; |
| int ret, slice, i; |
| u32 hdesc_size; |
| |
| slice = prueth_emac_slice(emac); |
| if (slice < 0) |
| return slice; |
| |
| init_completion(&emac->tdown_complete); |
| |
| hdesc_size = cppi5_hdesc_calc_size(true, PRUETH_NAV_PS_DATA_SIZE, |
| PRUETH_NAV_SW_DATA_SIZE); |
| memset(&tx_cfg, 0, sizeof(tx_cfg)); |
| tx_cfg.swdata_size = PRUETH_NAV_SW_DATA_SIZE; |
| tx_cfg.tx_cfg = ring_cfg; |
| tx_cfg.txcq_cfg = ring_cfg; |
| |
| for (i = 0; i < emac->tx_ch_num; i++) { |
| struct prueth_tx_chn *tx_chn = &emac->tx_chns[i]; |
| |
| /* To differentiate channels for SLICE0 vs SLICE1 */ |
| snprintf(tx_chn->name, sizeof(tx_chn->name), |
| "tx%d-%d", slice, i); |
| |
| tx_chn->emac = emac; |
| tx_chn->id = i; |
| tx_chn->descs_num = PRUETH_MAX_TX_DESC; |
| |
| tx_chn->tx_chn = |
| k3_udma_glue_request_tx_chn(dev, tx_chn->name, |
| &tx_cfg); |
| if (IS_ERR(tx_chn->tx_chn)) { |
| ret = PTR_ERR(tx_chn->tx_chn); |
| tx_chn->tx_chn = NULL; |
| netdev_err(ndev, |
| "Failed to request tx dma ch: %d\n", ret); |
| goto fail; |
| } |
| |
| tx_chn->dma_dev = k3_udma_glue_tx_get_dma_device(tx_chn->tx_chn); |
| tx_chn->desc_pool = |
| k3_cppi_desc_pool_create_name(tx_chn->dma_dev, |
| tx_chn->descs_num, |
| hdesc_size, |
| tx_chn->name); |
| if (IS_ERR(tx_chn->desc_pool)) { |
| ret = PTR_ERR(tx_chn->desc_pool); |
| tx_chn->desc_pool = NULL; |
| netdev_err(ndev, "Failed to create tx pool: %d\n", ret); |
| goto fail; |
| } |
| |
| ret = k3_udma_glue_tx_get_irq(tx_chn->tx_chn); |
| if (ret < 0) { |
| netdev_err(ndev, "failed to get tx irq\n"); |
| goto fail; |
| } |
| tx_chn->irq = ret; |
| |
| snprintf(tx_chn->name, sizeof(tx_chn->name), "%s-tx%d", |
| dev_name(dev), tx_chn->id); |
| } |
| |
| return 0; |
| |
| fail: |
| prueth_cleanup_tx_chns(emac); |
| return ret; |
| } |
| |
| static int prueth_init_rx_chns(struct prueth_emac *emac, |
| struct prueth_rx_chn *rx_chn, |
| char *name, u32 max_rflows, |
| u32 max_desc_num) |
| { |
| struct k3_udma_glue_rx_channel_cfg rx_cfg; |
| struct device *dev = emac->prueth->dev; |
| struct net_device *ndev = emac->ndev; |
| u32 fdqring_id, hdesc_size; |
| int i, ret = 0, slice; |
| |
| slice = prueth_emac_slice(emac); |
| if (slice < 0) |
| return slice; |
| |
| /* To differentiate channels for SLICE0 vs SLICE1 */ |
| snprintf(rx_chn->name, sizeof(rx_chn->name), "%s%d", name, slice); |
| |
| hdesc_size = cppi5_hdesc_calc_size(true, PRUETH_NAV_PS_DATA_SIZE, |
| PRUETH_NAV_SW_DATA_SIZE); |
| memset(&rx_cfg, 0, sizeof(rx_cfg)); |
| rx_cfg.swdata_size = PRUETH_NAV_SW_DATA_SIZE; |
| rx_cfg.flow_id_num = max_rflows; |
| rx_cfg.flow_id_base = -1; /* udmax will auto select flow id base */ |
| |
| /* init all flows */ |
| rx_chn->dev = dev; |
| rx_chn->descs_num = max_desc_num; |
| |
| rx_chn->rx_chn = k3_udma_glue_request_rx_chn(dev, rx_chn->name, |
| &rx_cfg); |
| if (IS_ERR(rx_chn->rx_chn)) { |
| ret = PTR_ERR(rx_chn->rx_chn); |
| rx_chn->rx_chn = NULL; |
| netdev_err(ndev, "Failed to request rx dma ch: %d\n", ret); |
| goto fail; |
| } |
| |
| rx_chn->dma_dev = k3_udma_glue_rx_get_dma_device(rx_chn->rx_chn); |
| rx_chn->desc_pool = k3_cppi_desc_pool_create_name(rx_chn->dma_dev, |
| rx_chn->descs_num, |
| hdesc_size, |
| rx_chn->name); |
| if (IS_ERR(rx_chn->desc_pool)) { |
| ret = PTR_ERR(rx_chn->desc_pool); |
| rx_chn->desc_pool = NULL; |
| netdev_err(ndev, "Failed to create rx pool: %d\n", ret); |
| goto fail; |
| } |
| |
| emac->rx_flow_id_base = k3_udma_glue_rx_get_flow_id_base(rx_chn->rx_chn); |
| netdev_dbg(ndev, "flow id base = %d\n", emac->rx_flow_id_base); |
| |
| fdqring_id = K3_RINGACC_RING_ID_ANY; |
| for (i = 0; i < rx_cfg.flow_id_num; i++) { |
| struct k3_ring_cfg rxring_cfg = { |
| .elm_size = K3_RINGACC_RING_ELSIZE_8, |
| .mode = K3_RINGACC_RING_MODE_RING, |
| .flags = 0, |
| }; |
| struct k3_ring_cfg fdqring_cfg = { |
| .elm_size = K3_RINGACC_RING_ELSIZE_8, |
| .flags = K3_RINGACC_RING_SHARED, |
| }; |
| struct k3_udma_glue_rx_flow_cfg rx_flow_cfg = { |
| .rx_cfg = rxring_cfg, |
| .rxfdq_cfg = fdqring_cfg, |
| .ring_rxq_id = K3_RINGACC_RING_ID_ANY, |
| .src_tag_lo_sel = |
| K3_UDMA_GLUE_SRC_TAG_LO_USE_REMOTE_SRC_TAG, |
| }; |
| |
| rx_flow_cfg.ring_rxfdq0_id = fdqring_id; |
| rx_flow_cfg.rx_cfg.size = max_desc_num; |
| rx_flow_cfg.rxfdq_cfg.size = max_desc_num; |
| rx_flow_cfg.rxfdq_cfg.mode = emac->prueth->pdata.fdqring_mode; |
| |
| ret = k3_udma_glue_rx_flow_init(rx_chn->rx_chn, |
| i, &rx_flow_cfg); |
| if (ret) { |
| netdev_err(ndev, "Failed to init rx flow%d %d\n", |
| i, ret); |
| goto fail; |
| } |
| if (!i) |
| fdqring_id = k3_udma_glue_rx_flow_get_fdq_id(rx_chn->rx_chn, |
| i); |
| rx_chn->irq[i] = k3_udma_glue_rx_get_irq(rx_chn->rx_chn, i); |
| if (rx_chn->irq[i] <= 0) { |
| ret = rx_chn->irq[i]; |
| netdev_err(ndev, "Failed to get rx dma irq"); |
| goto fail; |
| } |
| } |
| |
| return 0; |
| |
| fail: |
| prueth_cleanup_rx_chns(emac, rx_chn, max_rflows); |
| return ret; |
| } |
| |
| static int prueth_dma_rx_push(struct prueth_emac *emac, |
| struct sk_buff *skb, |
| struct prueth_rx_chn *rx_chn) |
| { |
| struct net_device *ndev = emac->ndev; |
| struct cppi5_host_desc_t *desc_rx; |
| u32 pkt_len = skb_tailroom(skb); |
| dma_addr_t desc_dma; |
| dma_addr_t buf_dma; |
| void **swdata; |
| |
| desc_rx = k3_cppi_desc_pool_alloc(rx_chn->desc_pool); |
| if (!desc_rx) { |
| netdev_err(ndev, "rx push: failed to allocate descriptor\n"); |
| return -ENOMEM; |
| } |
| desc_dma = k3_cppi_desc_pool_virt2dma(rx_chn->desc_pool, desc_rx); |
| |
| buf_dma = dma_map_single(rx_chn->dma_dev, skb->data, pkt_len, DMA_FROM_DEVICE); |
| if (unlikely(dma_mapping_error(rx_chn->dma_dev, buf_dma))) { |
| k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx); |
| netdev_err(ndev, "rx push: failed to map rx pkt buffer\n"); |
| return -EINVAL; |
| } |
| |
| cppi5_hdesc_init(desc_rx, CPPI5_INFO0_HDESC_EPIB_PRESENT, |
| PRUETH_NAV_PS_DATA_SIZE); |
| k3_udma_glue_rx_dma_to_cppi5_addr(rx_chn->rx_chn, &buf_dma); |
| cppi5_hdesc_attach_buf(desc_rx, buf_dma, skb_tailroom(skb), buf_dma, skb_tailroom(skb)); |
| |
| swdata = cppi5_hdesc_get_swdata(desc_rx); |
| *swdata = skb; |
| |
| return k3_udma_glue_push_rx_chn(rx_chn->rx_chn, 0, |
| desc_rx, desc_dma); |
| } |
| |
| static u64 icssg_ts_to_ns(u32 hi_sw, u32 hi, u32 lo, u32 cycle_time_ns) |
| { |
| u32 iepcount_lo, iepcount_hi, hi_rollover_count; |
| u64 ns; |
| |
| iepcount_lo = lo & GENMASK(19, 0); |
| iepcount_hi = (hi & GENMASK(11, 0)) << 12 | lo >> 20; |
| hi_rollover_count = hi >> 11; |
| |
| ns = ((u64)hi_rollover_count) << 23 | (iepcount_hi + hi_sw); |
| ns = ns * cycle_time_ns + iepcount_lo; |
| |
| return ns; |
| } |
| |
| static void emac_rx_timestamp(struct prueth_emac *emac, |
| struct sk_buff *skb, u32 *psdata) |
| { |
| struct skb_shared_hwtstamps *ssh; |
| u64 ns; |
| |
| u32 hi_sw = readl(emac->prueth->shram.va + |
| TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET); |
| ns = icssg_ts_to_ns(hi_sw, psdata[1], psdata[0], |
| IEP_DEFAULT_CYCLE_TIME_NS); |
| |
| ssh = skb_hwtstamps(skb); |
| memset(ssh, 0, sizeof(*ssh)); |
| ssh->hwtstamp = ns_to_ktime(ns); |
| } |
| |
| static int emac_rx_packet(struct prueth_emac *emac, u32 flow_id) |
| { |
| struct prueth_rx_chn *rx_chn = &emac->rx_chns; |
| u32 buf_dma_len, pkt_len, port_id = 0; |
| struct net_device *ndev = emac->ndev; |
| struct cppi5_host_desc_t *desc_rx; |
| struct sk_buff *skb, *new_skb; |
| dma_addr_t desc_dma, buf_dma; |
| void **swdata; |
| u32 *psdata; |
| int ret; |
| |
| ret = k3_udma_glue_pop_rx_chn(rx_chn->rx_chn, flow_id, &desc_dma); |
| if (ret) { |
| if (ret != -ENODATA) |
| netdev_err(ndev, "rx pop: failed: %d\n", ret); |
| return ret; |
| } |
| |
| if (cppi5_desc_is_tdcm(desc_dma)) /* Teardown ? */ |
| return 0; |
| |
| desc_rx = k3_cppi_desc_pool_dma2virt(rx_chn->desc_pool, desc_dma); |
| |
| swdata = cppi5_hdesc_get_swdata(desc_rx); |
| skb = *swdata; |
| |
| psdata = cppi5_hdesc_get_psdata(desc_rx); |
| /* RX HW timestamp */ |
| if (emac->rx_ts_enabled) |
| emac_rx_timestamp(emac, skb, psdata); |
| |
| cppi5_hdesc_get_obuf(desc_rx, &buf_dma, &buf_dma_len); |
| k3_udma_glue_rx_cppi5_to_dma_addr(rx_chn->rx_chn, &buf_dma); |
| pkt_len = cppi5_hdesc_get_pktlen(desc_rx); |
| /* firmware adds 4 CRC bytes, strip them */ |
| pkt_len -= 4; |
| cppi5_desc_get_tags_ids(&desc_rx->hdr, &port_id, NULL); |
| |
| dma_unmap_single(rx_chn->dma_dev, buf_dma, buf_dma_len, DMA_FROM_DEVICE); |
| k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx); |
| |
| skb->dev = ndev; |
| new_skb = netdev_alloc_skb_ip_align(ndev, PRUETH_MAX_PKT_SIZE); |
| /* if allocation fails we drop the packet but push the |
| * descriptor back to the ring with old skb to prevent a stall |
| */ |
| if (!new_skb) { |
| ndev->stats.rx_dropped++; |
| new_skb = skb; |
| } else { |
| /* send the filled skb up the n/w stack */ |
| skb_put(skb, pkt_len); |
| skb->protocol = eth_type_trans(skb, ndev); |
| napi_gro_receive(&emac->napi_rx, skb); |
| ndev->stats.rx_bytes += pkt_len; |
| ndev->stats.rx_packets++; |
| } |
| |
| /* queue another RX DMA */ |
| ret = prueth_dma_rx_push(emac, new_skb, &emac->rx_chns); |
| if (WARN_ON(ret < 0)) { |
| dev_kfree_skb_any(new_skb); |
| ndev->stats.rx_errors++; |
| ndev->stats.rx_dropped++; |
| } |
| |
| return ret; |
| } |
| |
| static void prueth_rx_cleanup(void *data, dma_addr_t desc_dma) |
| { |
| struct prueth_rx_chn *rx_chn = data; |
| struct cppi5_host_desc_t *desc_rx; |
| struct sk_buff *skb; |
| dma_addr_t buf_dma; |
| u32 buf_dma_len; |
| void **swdata; |
| |
| desc_rx = k3_cppi_desc_pool_dma2virt(rx_chn->desc_pool, desc_dma); |
| swdata = cppi5_hdesc_get_swdata(desc_rx); |
| skb = *swdata; |
| cppi5_hdesc_get_obuf(desc_rx, &buf_dma, &buf_dma_len); |
| k3_udma_glue_rx_cppi5_to_dma_addr(rx_chn->rx_chn, &buf_dma); |
| |
| dma_unmap_single(rx_chn->dma_dev, buf_dma, buf_dma_len, |
| DMA_FROM_DEVICE); |
| k3_cppi_desc_pool_free(rx_chn->desc_pool, desc_rx); |
| |
| dev_kfree_skb_any(skb); |
| } |
| |
| static int emac_get_tx_ts(struct prueth_emac *emac, |
| struct emac_tx_ts_response *rsp) |
| { |
| struct prueth *prueth = emac->prueth; |
| int slice = prueth_emac_slice(emac); |
| int addr; |
| |
| addr = icssg_queue_pop(prueth, slice == 0 ? |
| ICSSG_TS_POP_SLICE0 : ICSSG_TS_POP_SLICE1); |
| if (addr < 0) |
| return addr; |
| |
| memcpy_fromio(rsp, prueth->shram.va + addr, sizeof(*rsp)); |
| /* return buffer back for to pool */ |
| icssg_queue_push(prueth, slice == 0 ? |
| ICSSG_TS_PUSH_SLICE0 : ICSSG_TS_PUSH_SLICE1, addr); |
| |
| return 0; |
| } |
| |
| static void tx_ts_work(struct prueth_emac *emac) |
| { |
| struct skb_shared_hwtstamps ssh; |
| struct emac_tx_ts_response tsr; |
| struct sk_buff *skb; |
| int ret = 0; |
| u32 hi_sw; |
| u64 ns; |
| |
| /* There may be more than one pending requests */ |
| while (1) { |
| ret = emac_get_tx_ts(emac, &tsr); |
| if (ret) /* nothing more */ |
| break; |
| |
| if (tsr.cookie >= PRUETH_MAX_TX_TS_REQUESTS || |
| !emac->tx_ts_skb[tsr.cookie]) { |
| netdev_err(emac->ndev, "Invalid TX TS cookie 0x%x\n", |
| tsr.cookie); |
| break; |
| } |
| |
| skb = emac->tx_ts_skb[tsr.cookie]; |
| emac->tx_ts_skb[tsr.cookie] = NULL; /* free slot */ |
| if (!skb) { |
| netdev_err(emac->ndev, "Driver Bug! got NULL skb\n"); |
| break; |
| } |
| |
| hi_sw = readl(emac->prueth->shram.va + |
| TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET); |
| ns = icssg_ts_to_ns(hi_sw, tsr.hi_ts, tsr.lo_ts, |
| IEP_DEFAULT_CYCLE_TIME_NS); |
| |
| memset(&ssh, 0, sizeof(ssh)); |
| ssh.hwtstamp = ns_to_ktime(ns); |
| |
| skb_tstamp_tx(skb, &ssh); |
| dev_consume_skb_any(skb); |
| |
| if (atomic_dec_and_test(&emac->tx_ts_pending)) /* no more? */ |
| break; |
| } |
| } |
| |
| static int prueth_tx_ts_cookie_get(struct prueth_emac *emac) |
| { |
| int i; |
| |
| /* search and get the next free slot */ |
| for (i = 0; i < PRUETH_MAX_TX_TS_REQUESTS; i++) { |
| if (!emac->tx_ts_skb[i]) { |
| emac->tx_ts_skb[i] = ERR_PTR(-EBUSY); /* reserve slot */ |
| return i; |
| } |
| } |
| |
| return -EBUSY; |
| } |
| |
| /** |
| * emac_ndo_start_xmit - EMAC Transmit function |
| * @skb: SKB pointer |
| * @ndev: EMAC network adapter |
| * |
| * Called by the system to transmit a packet - we queue the packet in |
| * EMAC hardware transmit queue |
| * Doesn't wait for completion we'll check for TX completion in |
| * emac_tx_complete_packets(). |
| * |
| * Return: enum netdev_tx |
| */ |
| static enum netdev_tx emac_ndo_start_xmit(struct sk_buff *skb, struct net_device *ndev) |
| { |
| struct cppi5_host_desc_t *first_desc, *next_desc, *cur_desc; |
| struct prueth_emac *emac = netdev_priv(ndev); |
| struct netdev_queue *netif_txq; |
| struct prueth_tx_chn *tx_chn; |
| dma_addr_t desc_dma, buf_dma; |
| int i, ret = 0, q_idx; |
| bool in_tx_ts = 0; |
| int tx_ts_cookie; |
| void **swdata; |
| u32 pkt_len; |
| u32 *epib; |
| |
| pkt_len = skb_headlen(skb); |
| q_idx = skb_get_queue_mapping(skb); |
| |
| tx_chn = &emac->tx_chns[q_idx]; |
| netif_txq = netdev_get_tx_queue(ndev, q_idx); |
| |
| /* Map the linear buffer */ |
| buf_dma = dma_map_single(tx_chn->dma_dev, skb->data, pkt_len, DMA_TO_DEVICE); |
| if (dma_mapping_error(tx_chn->dma_dev, buf_dma)) { |
| netdev_err(ndev, "tx: failed to map skb buffer\n"); |
| ret = NETDEV_TX_OK; |
| goto drop_free_skb; |
| } |
| |
| first_desc = k3_cppi_desc_pool_alloc(tx_chn->desc_pool); |
| if (!first_desc) { |
| netdev_dbg(ndev, "tx: failed to allocate descriptor\n"); |
| dma_unmap_single(tx_chn->dma_dev, buf_dma, pkt_len, DMA_TO_DEVICE); |
| goto drop_stop_q_busy; |
| } |
| |
| cppi5_hdesc_init(first_desc, CPPI5_INFO0_HDESC_EPIB_PRESENT, |
| PRUETH_NAV_PS_DATA_SIZE); |
| cppi5_hdesc_set_pkttype(first_desc, 0); |
| epib = first_desc->epib; |
| epib[0] = 0; |
| epib[1] = 0; |
| if (skb_shinfo(skb)->tx_flags & SKBTX_HW_TSTAMP && |
| emac->tx_ts_enabled) { |
| tx_ts_cookie = prueth_tx_ts_cookie_get(emac); |
| if (tx_ts_cookie >= 0) { |
| skb_shinfo(skb)->tx_flags |= SKBTX_IN_PROGRESS; |
| /* Request TX timestamp */ |
| epib[0] = (u32)tx_ts_cookie; |
| epib[1] = 0x80000000; /* TX TS request */ |
| emac->tx_ts_skb[tx_ts_cookie] = skb_get(skb); |
| in_tx_ts = 1; |
| } |
| } |
| |
| /* set dst tag to indicate internal qid at the firmware which is at |
| * bit8..bit15. bit0..bit7 indicates port num for directed |
| * packets in case of switch mode operation |
| */ |
| cppi5_desc_set_tags_ids(&first_desc->hdr, 0, (emac->port_id | (q_idx << 8))); |
| k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &buf_dma); |
| cppi5_hdesc_attach_buf(first_desc, buf_dma, pkt_len, buf_dma, pkt_len); |
| swdata = cppi5_hdesc_get_swdata(first_desc); |
| *swdata = skb; |
| |
| /* Handle the case where skb is fragmented in pages */ |
| cur_desc = first_desc; |
| for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { |
| skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; |
| u32 frag_size = skb_frag_size(frag); |
| |
| next_desc = k3_cppi_desc_pool_alloc(tx_chn->desc_pool); |
| if (!next_desc) { |
| netdev_err(ndev, |
| "tx: failed to allocate frag. descriptor\n"); |
| goto free_desc_stop_q_busy_cleanup_tx_ts; |
| } |
| |
| buf_dma = skb_frag_dma_map(tx_chn->dma_dev, frag, 0, frag_size, |
| DMA_TO_DEVICE); |
| if (dma_mapping_error(tx_chn->dma_dev, buf_dma)) { |
| netdev_err(ndev, "tx: Failed to map skb page\n"); |
| k3_cppi_desc_pool_free(tx_chn->desc_pool, next_desc); |
| ret = NETDEV_TX_OK; |
| goto cleanup_tx_ts; |
| } |
| |
| cppi5_hdesc_reset_hbdesc(next_desc); |
| k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &buf_dma); |
| cppi5_hdesc_attach_buf(next_desc, |
| buf_dma, frag_size, buf_dma, frag_size); |
| |
| desc_dma = k3_cppi_desc_pool_virt2dma(tx_chn->desc_pool, |
| next_desc); |
| k3_udma_glue_tx_dma_to_cppi5_addr(tx_chn->tx_chn, &desc_dma); |
| cppi5_hdesc_link_hbdesc(cur_desc, desc_dma); |
| |
| pkt_len += frag_size; |
| cur_desc = next_desc; |
| } |
| WARN_ON_ONCE(pkt_len != skb->len); |
| |
| /* report bql before sending packet */ |
| netdev_tx_sent_queue(netif_txq, pkt_len); |
| |
| cppi5_hdesc_set_pktlen(first_desc, pkt_len); |
| desc_dma = k3_cppi_desc_pool_virt2dma(tx_chn->desc_pool, first_desc); |
| /* cppi5_desc_dump(first_desc, 64); */ |
| |
| skb_tx_timestamp(skb); /* SW timestamp if SKBTX_IN_PROGRESS not set */ |
| ret = k3_udma_glue_push_tx_chn(tx_chn->tx_chn, first_desc, desc_dma); |
| if (ret) { |
| netdev_err(ndev, "tx: push failed: %d\n", ret); |
| goto drop_free_descs; |
| } |
| |
| if (in_tx_ts) |
| atomic_inc(&emac->tx_ts_pending); |
| |
| if (k3_cppi_desc_pool_avail(tx_chn->desc_pool) < MAX_SKB_FRAGS) { |
| netif_tx_stop_queue(netif_txq); |
| /* Barrier, so that stop_queue visible to other cpus */ |
| smp_mb__after_atomic(); |
| |
| if (k3_cppi_desc_pool_avail(tx_chn->desc_pool) >= |
| MAX_SKB_FRAGS) |
| netif_tx_wake_queue(netif_txq); |
| } |
| |
| return NETDEV_TX_OK; |
| |
| cleanup_tx_ts: |
| if (in_tx_ts) { |
| dev_kfree_skb_any(emac->tx_ts_skb[tx_ts_cookie]); |
| emac->tx_ts_skb[tx_ts_cookie] = NULL; |
| } |
| |
| drop_free_descs: |
| prueth_xmit_free(tx_chn, first_desc); |
| |
| drop_free_skb: |
| dev_kfree_skb_any(skb); |
| |
| /* error */ |
| ndev->stats.tx_dropped++; |
| netdev_err(ndev, "tx: error: %d\n", ret); |
| |
| return ret; |
| |
| free_desc_stop_q_busy_cleanup_tx_ts: |
| if (in_tx_ts) { |
| dev_kfree_skb_any(emac->tx_ts_skb[tx_ts_cookie]); |
| emac->tx_ts_skb[tx_ts_cookie] = NULL; |
| } |
| prueth_xmit_free(tx_chn, first_desc); |
| |
| drop_stop_q_busy: |
| netif_tx_stop_queue(netif_txq); |
| return NETDEV_TX_BUSY; |
| } |
| |
| static void prueth_tx_cleanup(void *data, dma_addr_t desc_dma) |
| { |
| struct prueth_tx_chn *tx_chn = data; |
| struct cppi5_host_desc_t *desc_tx; |
| struct sk_buff *skb; |
| void **swdata; |
| |
| desc_tx = k3_cppi_desc_pool_dma2virt(tx_chn->desc_pool, desc_dma); |
| swdata = cppi5_hdesc_get_swdata(desc_tx); |
| skb = *(swdata); |
| prueth_xmit_free(tx_chn, desc_tx); |
| |
| dev_kfree_skb_any(skb); |
| } |
| |
| static irqreturn_t prueth_tx_ts_irq(int irq, void *dev_id) |
| { |
| struct prueth_emac *emac = dev_id; |
| |
| /* currently only TX timestamp is being returned */ |
| tx_ts_work(emac); |
| |
| return IRQ_HANDLED; |
| } |
| |
| static irqreturn_t prueth_rx_irq(int irq, void *dev_id) |
| { |
| struct prueth_emac *emac = dev_id; |
| |
| disable_irq_nosync(irq); |
| napi_schedule(&emac->napi_rx); |
| |
| return IRQ_HANDLED; |
| } |
| |
| struct icssg_firmwares { |
| char *pru; |
| char *rtu; |
| char *txpru; |
| }; |
| |
| static struct icssg_firmwares icssg_emac_firmwares[] = { |
| { |
| .pru = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf", |
| .rtu = "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf", |
| .txpru = "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf", |
| }, |
| { |
| .pru = "ti-pruss/am65x-sr2-pru1-prueth-fw.elf", |
| .rtu = "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf", |
| .txpru = "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf", |
| } |
| }; |
| |
| static int prueth_emac_start(struct prueth *prueth, struct prueth_emac *emac) |
| { |
| struct icssg_firmwares *firmwares; |
| struct device *dev = prueth->dev; |
| int slice, ret; |
| |
| firmwares = icssg_emac_firmwares; |
| |
| slice = prueth_emac_slice(emac); |
| if (slice < 0) { |
| netdev_err(emac->ndev, "invalid port\n"); |
| return -EINVAL; |
| } |
| |
| ret = icssg_config(prueth, emac, slice); |
| if (ret) |
| return ret; |
| |
| ret = rproc_set_firmware(prueth->pru[slice], firmwares[slice].pru); |
| ret = rproc_boot(prueth->pru[slice]); |
| if (ret) { |
| dev_err(dev, "failed to boot PRU%d: %d\n", slice, ret); |
| return -EINVAL; |
| } |
| |
| ret = rproc_set_firmware(prueth->rtu[slice], firmwares[slice].rtu); |
| ret = rproc_boot(prueth->rtu[slice]); |
| if (ret) { |
| dev_err(dev, "failed to boot RTU%d: %d\n", slice, ret); |
| goto halt_pru; |
| } |
| |
| ret = rproc_set_firmware(prueth->txpru[slice], firmwares[slice].txpru); |
| ret = rproc_boot(prueth->txpru[slice]); |
| if (ret) { |
| dev_err(dev, "failed to boot TX_PRU%d: %d\n", slice, ret); |
| goto halt_rtu; |
| } |
| |
| emac->fw_running = 1; |
| return 0; |
| |
| halt_rtu: |
| rproc_shutdown(prueth->rtu[slice]); |
| |
| halt_pru: |
| rproc_shutdown(prueth->pru[slice]); |
| |
| return ret; |
| } |
| |
| static void prueth_emac_stop(struct prueth_emac *emac) |
| { |
| struct prueth *prueth = emac->prueth; |
| int slice; |
| |
| switch (emac->port_id) { |
| case PRUETH_PORT_MII0: |
| slice = ICSS_SLICE0; |
| break; |
| case PRUETH_PORT_MII1: |
| slice = ICSS_SLICE1; |
| break; |
| default: |
| netdev_err(emac->ndev, "invalid port\n"); |
| return; |
| } |
| |
| emac->fw_running = 0; |
| rproc_shutdown(prueth->txpru[slice]); |
| rproc_shutdown(prueth->rtu[slice]); |
| rproc_shutdown(prueth->pru[slice]); |
| } |
| |
| static void prueth_cleanup_tx_ts(struct prueth_emac *emac) |
| { |
| int i; |
| |
| for (i = 0; i < PRUETH_MAX_TX_TS_REQUESTS; i++) { |
| if (emac->tx_ts_skb[i]) { |
| dev_kfree_skb_any(emac->tx_ts_skb[i]); |
| emac->tx_ts_skb[i] = NULL; |
| } |
| } |
| } |
| |
| /* called back by PHY layer if there is change in link state of hw port*/ |
| static void emac_adjust_link(struct net_device *ndev) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| struct phy_device *phydev = ndev->phydev; |
| struct prueth *prueth = emac->prueth; |
| bool new_state = false; |
| unsigned long flags; |
| |
| if (phydev->link) { |
| /* check the mode of operation - full/half duplex */ |
| if (phydev->duplex != emac->duplex) { |
| new_state = true; |
| emac->duplex = phydev->duplex; |
| } |
| if (phydev->speed != emac->speed) { |
| new_state = true; |
| emac->speed = phydev->speed; |
| } |
| if (!emac->link) { |
| new_state = true; |
| emac->link = 1; |
| } |
| } else if (emac->link) { |
| new_state = true; |
| emac->link = 0; |
| |
| /* f/w should support 100 & 1000 */ |
| emac->speed = SPEED_1000; |
| |
| /* half duplex may not be supported by f/w */ |
| emac->duplex = DUPLEX_FULL; |
| } |
| |
| if (new_state) { |
| phy_print_status(phydev); |
| |
| /* update RGMII and MII configuration based on PHY negotiated |
| * values |
| */ |
| if (emac->link) { |
| if (emac->duplex == DUPLEX_HALF) |
| icssg_config_half_duplex(emac); |
| /* Set the RGMII cfg for gig en and full duplex */ |
| icssg_update_rgmii_cfg(prueth->miig_rt, emac); |
| |
| /* update the Tx IPG based on 100M/1G speed */ |
| spin_lock_irqsave(&emac->lock, flags); |
| icssg_config_ipg(emac); |
| spin_unlock_irqrestore(&emac->lock, flags); |
| icssg_config_set_speed(emac); |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_FORWARD); |
| |
| } else { |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_DISABLE); |
| } |
| } |
| |
| if (emac->link) { |
| /* reactivate the transmit queue */ |
| netif_tx_wake_all_queues(ndev); |
| } else { |
| netif_tx_stop_all_queues(ndev); |
| prueth_cleanup_tx_ts(emac); |
| } |
| } |
| |
| static int emac_napi_rx_poll(struct napi_struct *napi_rx, int budget) |
| { |
| struct prueth_emac *emac = prueth_napi_to_emac(napi_rx); |
| int rx_flow = PRUETH_RX_FLOW_DATA; |
| int flow = PRUETH_MAX_RX_FLOWS; |
| int num_rx = 0; |
| int cur_budget; |
| int ret; |
| |
| while (flow--) { |
| cur_budget = budget - num_rx; |
| |
| while (cur_budget--) { |
| ret = emac_rx_packet(emac, flow); |
| if (ret) |
| break; |
| num_rx++; |
| } |
| |
| if (num_rx >= budget) |
| break; |
| } |
| |
| if (num_rx < budget && napi_complete_done(napi_rx, num_rx)) |
| enable_irq(emac->rx_chns.irq[rx_flow]); |
| |
| return num_rx; |
| } |
| |
| static int prueth_prepare_rx_chan(struct prueth_emac *emac, |
| struct prueth_rx_chn *chn, |
| int buf_size) |
| { |
| struct sk_buff *skb; |
| int i, ret; |
| |
| for (i = 0; i < chn->descs_num; i++) { |
| skb = __netdev_alloc_skb_ip_align(NULL, buf_size, GFP_KERNEL); |
| if (!skb) |
| return -ENOMEM; |
| |
| ret = prueth_dma_rx_push(emac, skb, chn); |
| if (ret < 0) { |
| netdev_err(emac->ndev, |
| "cannot submit skb for rx chan %s ret %d\n", |
| chn->name, ret); |
| kfree_skb(skb); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static void prueth_reset_tx_chan(struct prueth_emac *emac, int ch_num, |
| bool free_skb) |
| { |
| int i; |
| |
| for (i = 0; i < ch_num; i++) { |
| if (free_skb) |
| k3_udma_glue_reset_tx_chn(emac->tx_chns[i].tx_chn, |
| &emac->tx_chns[i], |
| prueth_tx_cleanup); |
| k3_udma_glue_disable_tx_chn(emac->tx_chns[i].tx_chn); |
| } |
| } |
| |
| static void prueth_reset_rx_chan(struct prueth_rx_chn *chn, |
| int num_flows, bool disable) |
| { |
| int i; |
| |
| for (i = 0; i < num_flows; i++) |
| k3_udma_glue_reset_rx_chn(chn->rx_chn, i, chn, |
| prueth_rx_cleanup, !!i); |
| if (disable) |
| k3_udma_glue_disable_rx_chn(chn->rx_chn); |
| } |
| |
| static int emac_phy_connect(struct prueth_emac *emac) |
| { |
| struct prueth *prueth = emac->prueth; |
| struct net_device *ndev = emac->ndev; |
| /* connect PHY */ |
| ndev->phydev = of_phy_connect(emac->ndev, emac->phy_node, |
| &emac_adjust_link, 0, |
| emac->phy_if); |
| if (!ndev->phydev) { |
| dev_err(prueth->dev, "couldn't connect to phy %s\n", |
| emac->phy_node->full_name); |
| return -ENODEV; |
| } |
| |
| if (!emac->half_duplex) { |
| dev_dbg(prueth->dev, "half duplex mode is not supported\n"); |
| phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT); |
| phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_100baseT_Half_BIT); |
| } |
| |
| /* remove unsupported modes */ |
| phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT); |
| phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Pause_BIT); |
| phy_remove_link_mode(ndev->phydev, ETHTOOL_LINK_MODE_Asym_Pause_BIT); |
| |
| if (emac->phy_if == PHY_INTERFACE_MODE_MII) |
| phy_set_max_speed(ndev->phydev, SPEED_100); |
| |
| return 0; |
| } |
| |
| static u64 prueth_iep_gettime(void *clockops_data, struct ptp_system_timestamp *sts) |
| { |
| u32 hi_rollover_count, hi_rollover_count_r; |
| struct prueth_emac *emac = clockops_data; |
| struct prueth *prueth = emac->prueth; |
| void __iomem *fw_hi_r_count_addr; |
| void __iomem *fw_count_hi_addr; |
| u32 iepcount_hi, iepcount_hi_r; |
| unsigned long flags; |
| u32 iepcount_lo; |
| u64 ts = 0; |
| |
| fw_count_hi_addr = prueth->shram.va + TIMESYNC_FW_WC_COUNT_HI_SW_OFFSET_OFFSET; |
| fw_hi_r_count_addr = prueth->shram.va + TIMESYNC_FW_WC_HI_ROLLOVER_COUNT_OFFSET; |
| |
| local_irq_save(flags); |
| do { |
| iepcount_hi = icss_iep_get_count_hi(emac->iep); |
| iepcount_hi += readl(fw_count_hi_addr); |
| hi_rollover_count = readl(fw_hi_r_count_addr); |
| ptp_read_system_prets(sts); |
| iepcount_lo = icss_iep_get_count_low(emac->iep); |
| ptp_read_system_postts(sts); |
| |
| iepcount_hi_r = icss_iep_get_count_hi(emac->iep); |
| iepcount_hi_r += readl(fw_count_hi_addr); |
| hi_rollover_count_r = readl(fw_hi_r_count_addr); |
| } while ((iepcount_hi_r != iepcount_hi) || |
| (hi_rollover_count != hi_rollover_count_r)); |
| local_irq_restore(flags); |
| |
| ts = ((u64)hi_rollover_count) << 23 | iepcount_hi; |
| ts = ts * (u64)IEP_DEFAULT_CYCLE_TIME_NS + iepcount_lo; |
| |
| return ts; |
| } |
| |
| static void prueth_iep_settime(void *clockops_data, u64 ns) |
| { |
| struct icssg_setclock_desc __iomem *sc_descp; |
| struct prueth_emac *emac = clockops_data; |
| struct icssg_setclock_desc sc_desc; |
| u64 cyclecount; |
| u32 cycletime; |
| int timeout; |
| |
| if (!emac->fw_running) |
| return; |
| |
| sc_descp = emac->prueth->shram.va + TIMESYNC_FW_WC_SETCLOCK_DESC_OFFSET; |
| |
| cycletime = IEP_DEFAULT_CYCLE_TIME_NS; |
| cyclecount = ns / cycletime; |
| |
| memset(&sc_desc, 0, sizeof(sc_desc)); |
| sc_desc.margin = cycletime - 1000; |
| sc_desc.cyclecounter0_set = cyclecount & GENMASK(31, 0); |
| sc_desc.cyclecounter1_set = (cyclecount & GENMASK(63, 32)) >> 32; |
| sc_desc.iepcount_set = ns % cycletime; |
| sc_desc.CMP0_current = cycletime - 4; //Count from 0 to (cycle time)-4 |
| |
| memcpy_toio(sc_descp, &sc_desc, sizeof(sc_desc)); |
| |
| writeb(1, &sc_descp->request); |
| |
| timeout = 5; /* fw should take 2-3 ms */ |
| while (timeout--) { |
| if (readb(&sc_descp->acknowledgment)) |
| return; |
| |
| usleep_range(500, 1000); |
| } |
| |
| dev_err(emac->prueth->dev, "settime timeout\n"); |
| } |
| |
| static int prueth_perout_enable(void *clockops_data, |
| struct ptp_perout_request *req, int on, |
| u64 *cmp) |
| { |
| struct prueth_emac *emac = clockops_data; |
| u32 reduction_factor = 0, offset = 0; |
| struct timespec64 ts; |
| u64 ns_period; |
| |
| if (!on) |
| return 0; |
| |
| /* Any firmware specific stuff for PPS/PEROUT handling */ |
| ts.tv_sec = req->period.sec; |
| ts.tv_nsec = req->period.nsec; |
| ns_period = timespec64_to_ns(&ts); |
| |
| /* f/w doesn't support period less than cycle time */ |
| if (ns_period < IEP_DEFAULT_CYCLE_TIME_NS) |
| return -ENXIO; |
| |
| reduction_factor = ns_period / IEP_DEFAULT_CYCLE_TIME_NS; |
| offset = ns_period % IEP_DEFAULT_CYCLE_TIME_NS; |
| |
| /* f/w requires at least 1uS within a cycle so CMP |
| * can trigger after SYNC is enabled |
| */ |
| if (offset < 5 * NSEC_PER_USEC) |
| offset = 5 * NSEC_PER_USEC; |
| |
| /* if offset is close to cycle time then we will miss |
| * the CMP event for last tick when IEP rolls over. |
| * In normal mode, IEP tick is 4ns. |
| * In slow compensation it could be 0ns or 8ns at |
| * every slow compensation cycle. |
| */ |
| if (offset > IEP_DEFAULT_CYCLE_TIME_NS - 8) |
| offset = IEP_DEFAULT_CYCLE_TIME_NS - 8; |
| |
| /* we're in shadow mode so need to set upper 32-bits */ |
| *cmp = (u64)offset << 32; |
| |
| writel(reduction_factor, emac->prueth->shram.va + |
| TIMESYNC_FW_WC_SYNCOUT_REDUCTION_FACTOR_OFFSET); |
| |
| writel(0, emac->prueth->shram.va + |
| TIMESYNC_FW_WC_SYNCOUT_START_TIME_CYCLECOUNT_OFFSET); |
| |
| return 0; |
| } |
| |
| const struct icss_iep_clockops prueth_iep_clockops = { |
| .settime = prueth_iep_settime, |
| .gettime = prueth_iep_gettime, |
| .perout_enable = prueth_perout_enable, |
| }; |
| |
| /** |
| * emac_ndo_open - EMAC device open |
| * @ndev: network adapter device |
| * |
| * Called when system wants to start the interface. |
| * |
| * Return: 0 for a successful open, or appropriate error code |
| */ |
| static int emac_ndo_open(struct net_device *ndev) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| int ret, i, num_data_chn = emac->tx_ch_num; |
| struct prueth *prueth = emac->prueth; |
| int slice = prueth_emac_slice(emac); |
| struct device *dev = prueth->dev; |
| int max_rx_flows; |
| int rx_flow; |
| |
| /* clear SMEM and MSMC settings for all slices */ |
| if (!prueth->emacs_initialized) { |
| memset_io(prueth->msmcram.va, 0, prueth->msmcram.size); |
| memset_io(prueth->shram.va, 0, ICSSG_CONFIG_OFFSET_SLICE1 * PRUETH_NUM_MACS); |
| } |
| |
| /* set h/w MAC as user might have re-configured */ |
| ether_addr_copy(emac->mac_addr, ndev->dev_addr); |
| |
| icssg_class_set_mac_addr(prueth->miig_rt, slice, emac->mac_addr); |
| icssg_ft1_set_mac_addr(prueth->miig_rt, slice, emac->mac_addr); |
| |
| icssg_class_default(prueth->miig_rt, slice, 0); |
| |
| /* Notify the stack of the actual queue counts. */ |
| ret = netif_set_real_num_tx_queues(ndev, num_data_chn); |
| if (ret) { |
| dev_err(dev, "cannot set real number of tx queues\n"); |
| return ret; |
| } |
| |
| init_completion(&emac->cmd_complete); |
| ret = prueth_init_tx_chns(emac); |
| if (ret) { |
| dev_err(dev, "failed to init tx channel: %d\n", ret); |
| return ret; |
| } |
| |
| max_rx_flows = PRUETH_MAX_RX_FLOWS; |
| ret = prueth_init_rx_chns(emac, &emac->rx_chns, "rx", |
| max_rx_flows, PRUETH_MAX_RX_DESC); |
| if (ret) { |
| dev_err(dev, "failed to init rx channel: %d\n", ret); |
| goto cleanup_tx; |
| } |
| |
| ret = prueth_ndev_add_tx_napi(emac); |
| if (ret) |
| goto cleanup_rx; |
| |
| /* we use only the highest priority flow for now i.e. @irq[3] */ |
| rx_flow = PRUETH_RX_FLOW_DATA; |
| ret = request_irq(emac->rx_chns.irq[rx_flow], prueth_rx_irq, |
| IRQF_TRIGGER_HIGH, dev_name(dev), emac); |
| if (ret) { |
| dev_err(dev, "unable to request RX IRQ\n"); |
| goto cleanup_napi; |
| } |
| |
| /* reset and start PRU firmware */ |
| ret = prueth_emac_start(prueth, emac); |
| if (ret) |
| goto free_rx_irq; |
| |
| icssg_mii_update_mtu(prueth->mii_rt, slice, ndev->max_mtu); |
| |
| if (!prueth->emacs_initialized) { |
| ret = icss_iep_init(emac->iep, &prueth_iep_clockops, |
| emac, IEP_DEFAULT_CYCLE_TIME_NS); |
| } |
| |
| ret = request_threaded_irq(emac->tx_ts_irq, NULL, prueth_tx_ts_irq, |
| IRQF_ONESHOT, dev_name(dev), emac); |
| if (ret) |
| goto stop; |
| |
| /* Prepare RX */ |
| ret = prueth_prepare_rx_chan(emac, &emac->rx_chns, PRUETH_MAX_PKT_SIZE); |
| if (ret) |
| goto free_tx_ts_irq; |
| |
| ret = k3_udma_glue_enable_rx_chn(emac->rx_chns.rx_chn); |
| if (ret) |
| goto reset_rx_chn; |
| |
| for (i = 0; i < emac->tx_ch_num; i++) { |
| ret = k3_udma_glue_enable_tx_chn(emac->tx_chns[i].tx_chn); |
| if (ret) |
| goto reset_tx_chan; |
| } |
| |
| /* Enable NAPI in Tx and Rx direction */ |
| for (i = 0; i < emac->tx_ch_num; i++) |
| napi_enable(&emac->tx_chns[i].napi_tx); |
| napi_enable(&emac->napi_rx); |
| |
| /* start PHY */ |
| phy_start(ndev->phydev); |
| |
| prueth->emacs_initialized++; |
| |
| queue_work(system_long_wq, &emac->stats_work.work); |
| |
| return 0; |
| |
| reset_tx_chan: |
| /* Since interface is not yet up, there is wouldn't be |
| * any SKB for completion. So set false to free_skb |
| */ |
| prueth_reset_tx_chan(emac, i, false); |
| reset_rx_chn: |
| prueth_reset_rx_chan(&emac->rx_chns, max_rx_flows, false); |
| free_tx_ts_irq: |
| free_irq(emac->tx_ts_irq, emac); |
| stop: |
| prueth_emac_stop(emac); |
| free_rx_irq: |
| free_irq(emac->rx_chns.irq[rx_flow], emac); |
| cleanup_napi: |
| prueth_ndev_del_tx_napi(emac, emac->tx_ch_num); |
| cleanup_rx: |
| prueth_cleanup_rx_chns(emac, &emac->rx_chns, max_rx_flows); |
| cleanup_tx: |
| prueth_cleanup_tx_chns(emac); |
| |
| return ret; |
| } |
| |
| /** |
| * emac_ndo_stop - EMAC device stop |
| * @ndev: network adapter device |
| * |
| * Called when system wants to stop or down the interface. |
| * |
| * Return: Always 0 (Success) |
| */ |
| static int emac_ndo_stop(struct net_device *ndev) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| struct prueth *prueth = emac->prueth; |
| int rx_flow = PRUETH_RX_FLOW_DATA; |
| int max_rx_flows; |
| int ret, i; |
| |
| /* inform the upper layers. */ |
| netif_tx_stop_all_queues(ndev); |
| |
| /* block packets from wire */ |
| if (ndev->phydev) |
| phy_stop(ndev->phydev); |
| |
| icssg_class_disable(prueth->miig_rt, prueth_emac_slice(emac)); |
| |
| atomic_set(&emac->tdown_cnt, emac->tx_ch_num); |
| /* ensure new tdown_cnt value is visible */ |
| smp_mb__after_atomic(); |
| /* tear down and disable UDMA channels */ |
| reinit_completion(&emac->tdown_complete); |
| for (i = 0; i < emac->tx_ch_num; i++) |
| k3_udma_glue_tdown_tx_chn(emac->tx_chns[i].tx_chn, false); |
| |
| ret = wait_for_completion_timeout(&emac->tdown_complete, |
| msecs_to_jiffies(1000)); |
| if (!ret) |
| netdev_err(ndev, "tx teardown timeout\n"); |
| |
| prueth_reset_tx_chan(emac, emac->tx_ch_num, true); |
| for (i = 0; i < emac->tx_ch_num; i++) |
| napi_disable(&emac->tx_chns[i].napi_tx); |
| |
| max_rx_flows = PRUETH_MAX_RX_FLOWS; |
| k3_udma_glue_tdown_rx_chn(emac->rx_chns.rx_chn, true); |
| |
| prueth_reset_rx_chan(&emac->rx_chns, max_rx_flows, true); |
| |
| napi_disable(&emac->napi_rx); |
| |
| cancel_work_sync(&emac->rx_mode_work); |
| |
| /* Destroying the queued work in ndo_stop() */ |
| cancel_delayed_work_sync(&emac->stats_work); |
| |
| if (prueth->emacs_initialized == 1) |
| icss_iep_exit(emac->iep); |
| |
| /* stop PRUs */ |
| prueth_emac_stop(emac); |
| |
| free_irq(emac->tx_ts_irq, emac); |
| |
| free_irq(emac->rx_chns.irq[rx_flow], emac); |
| prueth_ndev_del_tx_napi(emac, emac->tx_ch_num); |
| |
| prueth_cleanup_rx_chns(emac, &emac->rx_chns, max_rx_flows); |
| prueth_cleanup_tx_chns(emac); |
| |
| prueth->emacs_initialized--; |
| |
| return 0; |
| } |
| |
| static void emac_ndo_tx_timeout(struct net_device *ndev, unsigned int txqueue) |
| { |
| ndev->stats.tx_errors++; |
| } |
| |
| static void emac_ndo_set_rx_mode_work(struct work_struct *work) |
| { |
| struct prueth_emac *emac = container_of(work, struct prueth_emac, rx_mode_work); |
| struct net_device *ndev = emac->ndev; |
| bool promisc, allmulti; |
| |
| if (!netif_running(ndev)) |
| return; |
| |
| promisc = ndev->flags & IFF_PROMISC; |
| allmulti = ndev->flags & IFF_ALLMULTI; |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_UC_FLOODING_DISABLE); |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_DISABLE); |
| |
| if (promisc) { |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_UC_FLOODING_ENABLE); |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE); |
| return; |
| } |
| |
| if (allmulti) { |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE); |
| return; |
| } |
| |
| if (!netdev_mc_empty(ndev)) { |
| emac_set_port_state(emac, ICSSG_EMAC_PORT_MC_FLOODING_ENABLE); |
| return; |
| } |
| } |
| |
| /** |
| * emac_ndo_set_rx_mode - EMAC set receive mode function |
| * @ndev: The EMAC network adapter |
| * |
| * Called when system wants to set the receive mode of the device. |
| * |
| */ |
| static void emac_ndo_set_rx_mode(struct net_device *ndev) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| |
| queue_work(emac->cmd_wq, &emac->rx_mode_work); |
| } |
| |
| static int emac_set_ts_config(struct net_device *ndev, struct ifreq *ifr) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| struct hwtstamp_config config; |
| |
| if (copy_from_user(&config, ifr->ifr_data, sizeof(config))) |
| return -EFAULT; |
| |
| switch (config.tx_type) { |
| case HWTSTAMP_TX_OFF: |
| emac->tx_ts_enabled = 0; |
| break; |
| case HWTSTAMP_TX_ON: |
| emac->tx_ts_enabled = 1; |
| break; |
| default: |
| return -ERANGE; |
| } |
| |
| switch (config.rx_filter) { |
| case HWTSTAMP_FILTER_NONE: |
| emac->rx_ts_enabled = 0; |
| break; |
| case HWTSTAMP_FILTER_ALL: |
| case HWTSTAMP_FILTER_SOME: |
| case HWTSTAMP_FILTER_PTP_V1_L4_EVENT: |
| case HWTSTAMP_FILTER_PTP_V1_L4_SYNC: |
| case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ: |
| case HWTSTAMP_FILTER_PTP_V2_L4_EVENT: |
| case HWTSTAMP_FILTER_PTP_V2_L4_SYNC: |
| case HWTSTAMP_FILTER_PTP_V2_L4_DELAY_REQ: |
| case HWTSTAMP_FILTER_PTP_V2_L2_EVENT: |
| case HWTSTAMP_FILTER_PTP_V2_L2_SYNC: |
| case HWTSTAMP_FILTER_PTP_V2_L2_DELAY_REQ: |
| case HWTSTAMP_FILTER_PTP_V2_EVENT: |
| case HWTSTAMP_FILTER_PTP_V2_SYNC: |
| case HWTSTAMP_FILTER_PTP_V2_DELAY_REQ: |
| case HWTSTAMP_FILTER_NTP_ALL: |
| emac->rx_ts_enabled = 1; |
| config.rx_filter = HWTSTAMP_FILTER_ALL; |
| break; |
| default: |
| return -ERANGE; |
| } |
| |
| return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ? |
| -EFAULT : 0; |
| } |
| |
| static int emac_get_ts_config(struct net_device *ndev, struct ifreq *ifr) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| struct hwtstamp_config config; |
| |
| config.flags = 0; |
| config.tx_type = emac->tx_ts_enabled ? HWTSTAMP_TX_ON : HWTSTAMP_TX_OFF; |
| config.rx_filter = emac->rx_ts_enabled ? HWTSTAMP_FILTER_ALL : HWTSTAMP_FILTER_NONE; |
| |
| return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ? |
| -EFAULT : 0; |
| } |
| |
| static int emac_ndo_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd) |
| { |
| switch (cmd) { |
| case SIOCGHWTSTAMP: |
| return emac_get_ts_config(ndev, ifr); |
| case SIOCSHWTSTAMP: |
| return emac_set_ts_config(ndev, ifr); |
| default: |
| break; |
| } |
| |
| return phy_do_ioctl(ndev, ifr, cmd); |
| } |
| |
| static void emac_ndo_get_stats64(struct net_device *ndev, |
| struct rtnl_link_stats64 *stats) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| |
| emac_update_hardware_stats(emac); |
| |
| stats->rx_packets = emac_get_stat_by_name(emac, "rx_packets"); |
| stats->rx_bytes = emac_get_stat_by_name(emac, "rx_bytes"); |
| stats->tx_packets = emac_get_stat_by_name(emac, "tx_packets"); |
| stats->tx_bytes = emac_get_stat_by_name(emac, "tx_bytes"); |
| stats->rx_crc_errors = emac_get_stat_by_name(emac, "rx_crc_errors"); |
| stats->rx_over_errors = emac_get_stat_by_name(emac, "rx_over_errors"); |
| stats->multicast = emac_get_stat_by_name(emac, "rx_multicast_frames"); |
| |
| stats->rx_errors = ndev->stats.rx_errors; |
| stats->rx_dropped = ndev->stats.rx_dropped; |
| stats->tx_errors = ndev->stats.tx_errors; |
| stats->tx_dropped = ndev->stats.tx_dropped; |
| } |
| |
| static int emac_ndo_get_phys_port_name(struct net_device *ndev, char *name, |
| size_t len) |
| { |
| struct prueth_emac *emac = netdev_priv(ndev); |
| int ret; |
| |
| ret = snprintf(name, len, "p%d", emac->port_id); |
| if (ret >= len) |
| return -EINVAL; |
| |
| return 0; |
| } |
| |
| static const struct net_device_ops emac_netdev_ops = { |
| .ndo_open = emac_ndo_open, |
| .ndo_stop = emac_ndo_stop, |
| .ndo_start_xmit = emac_ndo_start_xmit, |
| .ndo_set_mac_address = eth_mac_addr, |
| .ndo_validate_addr = eth_validate_addr, |
| .ndo_tx_timeout = emac_ndo_tx_timeout, |
| .ndo_set_rx_mode = emac_ndo_set_rx_mode, |
| .ndo_eth_ioctl = emac_ndo_ioctl, |
| .ndo_get_stats64 = emac_ndo_get_stats64, |
| .ndo_get_phys_port_name = emac_ndo_get_phys_port_name, |
| }; |
| |
| /* get emac_port corresponding to eth_node name */ |
| static int prueth_node_port(struct device_node *eth_node) |
| { |
| u32 port_id; |
| int ret; |
| |
| ret = of_property_read_u32(eth_node, "reg", &port_id); |
| if (ret) |
| return ret; |
| |
| if (port_id == 0) |
| return PRUETH_PORT_MII0; |
| else if (port_id == 1) |
| return PRUETH_PORT_MII1; |
| else |
| return PRUETH_PORT_INVALID; |
| } |
| |
| /* get MAC instance corresponding to eth_node name */ |
| static int prueth_node_mac(struct device_node *eth_node) |
| { |
| u32 port_id; |
| int ret; |
| |
| ret = of_property_read_u32(eth_node, "reg", &port_id); |
| if (ret) |
| return ret; |
| |
| if (port_id == 0) |
| return PRUETH_MAC0; |
| else if (port_id == 1) |
| return PRUETH_MAC1; |
| else |
| return PRUETH_MAC_INVALID; |
| } |
| |
| static int prueth_netdev_init(struct prueth *prueth, |
| struct device_node *eth_node) |
| { |
| int ret, num_tx_chn = PRUETH_MAX_TX_QUEUES; |
| struct prueth_emac *emac; |
| struct net_device *ndev; |
| enum prueth_port port; |
| const char *irq_name; |
| enum prueth_mac mac; |
| |
| port = prueth_node_port(eth_node); |
| if (port == PRUETH_PORT_INVALID) |
| return -EINVAL; |
| |
| mac = prueth_node_mac(eth_node); |
| if (mac == PRUETH_MAC_INVALID) |
| return -EINVAL; |
| |
| ndev = alloc_etherdev_mq(sizeof(*emac), num_tx_chn); |
| if (!ndev) |
| return -ENOMEM; |
| |
| emac = netdev_priv(ndev); |
| emac->prueth = prueth; |
| emac->ndev = ndev; |
| emac->port_id = port; |
| emac->cmd_wq = create_singlethread_workqueue("icssg_cmd_wq"); |
| if (!emac->cmd_wq) { |
| ret = -ENOMEM; |
| goto free_ndev; |
| } |
| INIT_WORK(&emac->rx_mode_work, emac_ndo_set_rx_mode_work); |
| |
| INIT_DELAYED_WORK(&emac->stats_work, emac_stats_work_handler); |
| |
| ret = pruss_request_mem_region(prueth->pruss, |
| port == PRUETH_PORT_MII0 ? |
| PRUSS_MEM_DRAM0 : PRUSS_MEM_DRAM1, |
| &emac->dram); |
| if (ret) { |
| dev_err(prueth->dev, "unable to get DRAM: %d\n", ret); |
| ret = -ENOMEM; |
| goto free_wq; |
| } |
| |
| emac->tx_ch_num = 1; |
| |
| irq_name = "tx_ts0"; |
| if (emac->port_id == PRUETH_PORT_MII1) |
| irq_name = "tx_ts1"; |
| emac->tx_ts_irq = platform_get_irq_byname_optional(prueth->pdev, irq_name); |
| if (emac->tx_ts_irq < 0) { |
| ret = dev_err_probe(prueth->dev, emac->tx_ts_irq, "could not get tx_ts_irq\n"); |
| goto free; |
| } |
| |
| SET_NETDEV_DEV(ndev, prueth->dev); |
| spin_lock_init(&emac->lock); |
| mutex_init(&emac->cmd_lock); |
| |
| emac->phy_node = of_parse_phandle(eth_node, "phy-handle", 0); |
| if (!emac->phy_node && !of_phy_is_fixed_link(eth_node)) { |
| dev_err(prueth->dev, "couldn't find phy-handle\n"); |
| ret = -ENODEV; |
| goto free; |
| } else if (of_phy_is_fixed_link(eth_node)) { |
| ret = of_phy_register_fixed_link(eth_node); |
| if (ret) { |
| ret = dev_err_probe(prueth->dev, ret, |
| "failed to register fixed-link phy\n"); |
| goto free; |
| } |
| |
| emac->phy_node = eth_node; |
| } |
| |
| ret = of_get_phy_mode(eth_node, &emac->phy_if); |
| if (ret) { |
| dev_err(prueth->dev, "could not get phy-mode property\n"); |
| goto free; |
| } |
| |
| if (emac->phy_if != PHY_INTERFACE_MODE_MII && |
| !phy_interface_mode_is_rgmii(emac->phy_if)) { |
| dev_err(prueth->dev, "PHY mode unsupported %s\n", phy_modes(emac->phy_if)); |
| ret = -EINVAL; |
| goto free; |
| } |
| |
| /* AM65 SR2.0 has TX Internal delay always enabled by hardware |
| * and it is not possible to disable TX Internal delay. The below |
| * switch case block describes how we handle different phy modes |
| * based on hardware restriction. |
| */ |
| switch (emac->phy_if) { |
| case PHY_INTERFACE_MODE_RGMII_ID: |
| emac->phy_if = PHY_INTERFACE_MODE_RGMII_RXID; |
| break; |
| case PHY_INTERFACE_MODE_RGMII_TXID: |
| emac->phy_if = PHY_INTERFACE_MODE_RGMII; |
| break; |
| case PHY_INTERFACE_MODE_RGMII: |
| case PHY_INTERFACE_MODE_RGMII_RXID: |
| dev_err(prueth->dev, "RGMII mode without TX delay is not supported"); |
| ret = -EINVAL; |
| goto free; |
| default: |
| break; |
| } |
| |
| /* get mac address from DT and set private and netdev addr */ |
| ret = of_get_ethdev_address(eth_node, ndev); |
| if (!is_valid_ether_addr(ndev->dev_addr)) { |
| eth_hw_addr_random(ndev); |
| dev_warn(prueth->dev, "port %d: using random MAC addr: %pM\n", |
| port, ndev->dev_addr); |
| } |
| ether_addr_copy(emac->mac_addr, ndev->dev_addr); |
| |
| ndev->min_mtu = PRUETH_MIN_PKT_SIZE; |
| ndev->max_mtu = PRUETH_MAX_MTU; |
| ndev->netdev_ops = &emac_netdev_ops; |
| ndev->ethtool_ops = &icssg_ethtool_ops; |
| ndev->hw_features = NETIF_F_SG; |
| ndev->features = ndev->hw_features; |
| |
| netif_napi_add(ndev, &emac->napi_rx, emac_napi_rx_poll); |
| prueth->emac[mac] = emac; |
| |
| return 0; |
| |
| free: |
| pruss_release_mem_region(prueth->pruss, &emac->dram); |
| free_wq: |
| destroy_workqueue(emac->cmd_wq); |
| free_ndev: |
| emac->ndev = NULL; |
| prueth->emac[mac] = NULL; |
| free_netdev(ndev); |
| |
| return ret; |
| } |
| |
| static void prueth_netdev_exit(struct prueth *prueth, |
| struct device_node *eth_node) |
| { |
| struct prueth_emac *emac; |
| enum prueth_mac mac; |
| |
| mac = prueth_node_mac(eth_node); |
| if (mac == PRUETH_MAC_INVALID) |
| return; |
| |
| emac = prueth->emac[mac]; |
| if (!emac) |
| return; |
| |
| if (of_phy_is_fixed_link(emac->phy_node)) |
| of_phy_deregister_fixed_link(emac->phy_node); |
| |
| netif_napi_del(&emac->napi_rx); |
| |
| pruss_release_mem_region(prueth->pruss, &emac->dram); |
| destroy_workqueue(emac->cmd_wq); |
| free_netdev(emac->ndev); |
| prueth->emac[mac] = NULL; |
| } |
| |
| static int prueth_get_cores(struct prueth *prueth, int slice) |
| { |
| struct device *dev = prueth->dev; |
| enum pruss_pru_id pruss_id; |
| struct device_node *np; |
| int idx = -1, ret; |
| |
| np = dev->of_node; |
| |
| switch (slice) { |
| case ICSS_SLICE0: |
| idx = 0; |
| break; |
| case ICSS_SLICE1: |
| idx = 3; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| prueth->pru[slice] = pru_rproc_get(np, idx, &pruss_id); |
| if (IS_ERR(prueth->pru[slice])) { |
| ret = PTR_ERR(prueth->pru[slice]); |
| prueth->pru[slice] = NULL; |
| return dev_err_probe(dev, ret, "unable to get PRU%d\n", slice); |
| } |
| prueth->pru_id[slice] = pruss_id; |
| |
| idx++; |
| prueth->rtu[slice] = pru_rproc_get(np, idx, NULL); |
| if (IS_ERR(prueth->rtu[slice])) { |
| ret = PTR_ERR(prueth->rtu[slice]); |
| prueth->rtu[slice] = NULL; |
| return dev_err_probe(dev, ret, "unable to get RTU%d\n", slice); |
| } |
| |
| idx++; |
| prueth->txpru[slice] = pru_rproc_get(np, idx, NULL); |
| if (IS_ERR(prueth->txpru[slice])) { |
| ret = PTR_ERR(prueth->txpru[slice]); |
| prueth->txpru[slice] = NULL; |
| return dev_err_probe(dev, ret, "unable to get TX_PRU%d\n", slice); |
| } |
| |
| return 0; |
| } |
| |
| static void prueth_put_cores(struct prueth *prueth, int slice) |
| { |
| if (prueth->txpru[slice]) |
| pru_rproc_put(prueth->txpru[slice]); |
| |
| if (prueth->rtu[slice]) |
| pru_rproc_put(prueth->rtu[slice]); |
| |
| if (prueth->pru[slice]) |
| pru_rproc_put(prueth->pru[slice]); |
| } |
| |
| static int prueth_probe(struct platform_device *pdev) |
| { |
| struct device_node *eth_node, *eth_ports_node; |
| struct device_node *eth0_node = NULL; |
| struct device_node *eth1_node = NULL; |
| struct genpool_data_align gp_data = { |
| .align = SZ_64K, |
| }; |
| struct device *dev = &pdev->dev; |
| struct device_node *np; |
| struct prueth *prueth; |
| struct pruss *pruss; |
| u32 msmc_ram_size; |
| int i, ret; |
| |
| np = dev->of_node; |
| |
| prueth = devm_kzalloc(dev, sizeof(*prueth), GFP_KERNEL); |
| if (!prueth) |
| return -ENOMEM; |
| |
| dev_set_drvdata(dev, prueth); |
| prueth->pdev = pdev; |
| prueth->pdata = *(const struct prueth_pdata *)device_get_match_data(dev); |
| |
| prueth->dev = dev; |
| eth_ports_node = of_get_child_by_name(np, "ethernet-ports"); |
| if (!eth_ports_node) |
| return -ENOENT; |
| |
| for_each_child_of_node(eth_ports_node, eth_node) { |
| u32 reg; |
| |
| if (strcmp(eth_node->name, "port")) |
| continue; |
| ret = of_property_read_u32(eth_node, "reg", ®); |
| if (ret < 0) { |
| dev_err(dev, "%pOF error reading port_id %d\n", |
| eth_node, ret); |
| } |
| |
| of_node_get(eth_node); |
| |
| if (reg == 0) { |
| eth0_node = eth_node; |
| if (!of_device_is_available(eth0_node)) { |
| of_node_put(eth0_node); |
| eth0_node = NULL; |
| } |
| } else if (reg == 1) { |
| eth1_node = eth_node; |
| if (!of_device_is_available(eth1_node)) { |
| of_node_put(eth1_node); |
| eth1_node = NULL; |
| } |
| } else { |
| dev_err(dev, "port reg should be 0 or 1\n"); |
| } |
| } |
| |
| of_node_put(eth_ports_node); |
| |
| /* At least one node must be present and available else we fail */ |
| if (!eth0_node && !eth1_node) { |
| dev_err(dev, "neither port0 nor port1 node available\n"); |
| return -ENODEV; |
| } |
| |
| if (eth0_node == eth1_node) { |
| dev_err(dev, "port0 and port1 can't have same reg\n"); |
| of_node_put(eth0_node); |
| return -ENODEV; |
| } |
| |
| prueth->eth_node[PRUETH_MAC0] = eth0_node; |
| prueth->eth_node[PRUETH_MAC1] = eth1_node; |
| |
| prueth->miig_rt = syscon_regmap_lookup_by_phandle(np, "ti,mii-g-rt"); |
| if (IS_ERR(prueth->miig_rt)) { |
| dev_err(dev, "couldn't get ti,mii-g-rt syscon regmap\n"); |
| return -ENODEV; |
| } |
| |
| prueth->mii_rt = syscon_regmap_lookup_by_phandle(np, "ti,mii-rt"); |
| if (IS_ERR(prueth->mii_rt)) { |
| dev_err(dev, "couldn't get ti,mii-rt syscon regmap\n"); |
| return -ENODEV; |
| } |
| |
| if (eth0_node) { |
| ret = prueth_get_cores(prueth, ICSS_SLICE0); |
| if (ret) |
| goto put_cores; |
| } |
| |
| if (eth1_node) { |
| ret = prueth_get_cores(prueth, ICSS_SLICE1); |
| if (ret) |
| goto put_cores; |
| } |
| |
| pruss = pruss_get(eth0_node ? |
| prueth->pru[ICSS_SLICE0] : prueth->pru[ICSS_SLICE1]); |
| if (IS_ERR(pruss)) { |
| ret = PTR_ERR(pruss); |
| dev_err(dev, "unable to get pruss handle\n"); |
| goto put_cores; |
| } |
| |
| prueth->pruss = pruss; |
| |
| ret = pruss_request_mem_region(pruss, PRUSS_MEM_SHRD_RAM2, |
| &prueth->shram); |
| if (ret) { |
| dev_err(dev, "unable to get PRUSS SHRD RAM2: %d\n", ret); |
| goto put_pruss; |
| } |
| |
| prueth->sram_pool = of_gen_pool_get(np, "sram", 0); |
| if (!prueth->sram_pool) { |
| dev_err(dev, "unable to get SRAM pool\n"); |
| ret = -ENODEV; |
| |
| goto put_mem; |
| } |
| |
| msmc_ram_size = MSMC_RAM_SIZE; |
| |
| /* NOTE: FW bug needs buffer base to be 64KB aligned */ |
| prueth->msmcram.va = |
| (void __iomem *)gen_pool_alloc_algo(prueth->sram_pool, |
| msmc_ram_size, |
| gen_pool_first_fit_align, |
| &gp_data); |
| |
| if (!prueth->msmcram.va) { |
| ret = -ENOMEM; |
| dev_err(dev, "unable to allocate MSMC resource\n"); |
| goto put_mem; |
| } |
| prueth->msmcram.pa = gen_pool_virt_to_phys(prueth->sram_pool, |
| (unsigned long)prueth->msmcram.va); |
| prueth->msmcram.size = msmc_ram_size; |
| memset_io(prueth->msmcram.va, 0, msmc_ram_size); |
| dev_dbg(dev, "sram: pa %llx va %p size %zx\n", prueth->msmcram.pa, |
| prueth->msmcram.va, prueth->msmcram.size); |
| |
| prueth->iep0 = icss_iep_get_idx(np, 0); |
| if (IS_ERR(prueth->iep0)) { |
| ret = dev_err_probe(dev, PTR_ERR(prueth->iep0), "iep0 get failed\n"); |
| prueth->iep0 = NULL; |
| goto free_pool; |
| } |
| |
| prueth->iep1 = icss_iep_get_idx(np, 1); |
| if (IS_ERR(prueth->iep1)) { |
| ret = dev_err_probe(dev, PTR_ERR(prueth->iep1), "iep1 get failed\n"); |
| goto put_iep0; |
| } |
| |
| if (prueth->pdata.quirk_10m_link_issue) { |
| /* Enable IEP1 for FW in 64bit mode as W/A for 10M FD link detect issue under TX |
| * traffic. |
| */ |
| icss_iep_init_fw(prueth->iep1); |
| } |
| |
| /* setup netdev interfaces */ |
| if (eth0_node) { |
| ret = prueth_netdev_init(prueth, eth0_node); |
| if (ret) { |
| dev_err_probe(dev, ret, "netdev init %s failed\n", |
| eth0_node->name); |
| goto exit_iep; |
| } |
| |
| if (of_find_property(eth0_node, "ti,half-duplex-capable", NULL)) |
| prueth->emac[PRUETH_MAC0]->half_duplex = 1; |
| |
| prueth->emac[PRUETH_MAC0]->iep = prueth->iep0; |
| } |
| |
| if (eth1_node) { |
| ret = prueth_netdev_init(prueth, eth1_node); |
| if (ret) { |
| dev_err_probe(dev, ret, "netdev init %s failed\n", |
| eth1_node->name); |
| goto netdev_exit; |
| } |
| |
| if (of_find_property(eth1_node, "ti,half-duplex-capable", NULL)) |
| prueth->emac[PRUETH_MAC1]->half_duplex = 1; |
| |
| prueth->emac[PRUETH_MAC1]->iep = prueth->iep0; |
| } |
| |
| /* register the network devices */ |
| if (eth0_node) { |
| ret = register_netdev(prueth->emac[PRUETH_MAC0]->ndev); |
| if (ret) { |
| dev_err(dev, "can't register netdev for port MII0"); |
| goto netdev_exit; |
| } |
| |
| prueth->registered_netdevs[PRUETH_MAC0] = prueth->emac[PRUETH_MAC0]->ndev; |
| |
| emac_phy_connect(prueth->emac[PRUETH_MAC0]); |
| phy_attached_info(prueth->emac[PRUETH_MAC0]->ndev->phydev); |
| } |
| |
| if (eth1_node) { |
| ret = register_netdev(prueth->emac[PRUETH_MAC1]->ndev); |
| if (ret) { |
| dev_err(dev, "can't register netdev for port MII1"); |
| goto netdev_unregister; |
| } |
| |
| prueth->registered_netdevs[PRUETH_MAC1] = prueth->emac[PRUETH_MAC1]->ndev; |
| emac_phy_connect(prueth->emac[PRUETH_MAC1]); |
| phy_attached_info(prueth->emac[PRUETH_MAC1]->ndev->phydev); |
| } |
| |
| dev_info(dev, "TI PRU ethernet driver initialized: %s EMAC mode\n", |
| (!eth0_node || !eth1_node) ? "single" : "dual"); |
| |
| if (eth1_node) |
| of_node_put(eth1_node); |
| if (eth0_node) |
| of_node_put(eth0_node); |
| return 0; |
| |
| netdev_unregister: |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| if (!prueth->registered_netdevs[i]) |
| continue; |
| if (prueth->emac[i]->ndev->phydev) { |
| phy_disconnect(prueth->emac[i]->ndev->phydev); |
| prueth->emac[i]->ndev->phydev = NULL; |
| } |
| unregister_netdev(prueth->registered_netdevs[i]); |
| } |
| |
| netdev_exit: |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| eth_node = prueth->eth_node[i]; |
| if (!eth_node) |
| continue; |
| |
| prueth_netdev_exit(prueth, eth_node); |
| } |
| |
| exit_iep: |
| if (prueth->pdata.quirk_10m_link_issue) |
| icss_iep_exit_fw(prueth->iep1); |
| icss_iep_put(prueth->iep1); |
| |
| put_iep0: |
| icss_iep_put(prueth->iep0); |
| prueth->iep0 = NULL; |
| prueth->iep1 = NULL; |
| |
| free_pool: |
| gen_pool_free(prueth->sram_pool, |
| (unsigned long)prueth->msmcram.va, msmc_ram_size); |
| |
| put_mem: |
| pruss_release_mem_region(prueth->pruss, &prueth->shram); |
| |
| put_pruss: |
| pruss_put(prueth->pruss); |
| |
| put_cores: |
| if (eth1_node) { |
| prueth_put_cores(prueth, ICSS_SLICE1); |
| of_node_put(eth1_node); |
| } |
| |
| if (eth0_node) { |
| prueth_put_cores(prueth, ICSS_SLICE0); |
| of_node_put(eth0_node); |
| } |
| |
| return ret; |
| } |
| |
| static void prueth_remove(struct platform_device *pdev) |
| { |
| struct prueth *prueth = platform_get_drvdata(pdev); |
| struct device_node *eth_node; |
| int i; |
| |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| if (!prueth->registered_netdevs[i]) |
| continue; |
| phy_stop(prueth->emac[i]->ndev->phydev); |
| phy_disconnect(prueth->emac[i]->ndev->phydev); |
| prueth->emac[i]->ndev->phydev = NULL; |
| unregister_netdev(prueth->registered_netdevs[i]); |
| } |
| |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| eth_node = prueth->eth_node[i]; |
| if (!eth_node) |
| continue; |
| |
| prueth_netdev_exit(prueth, eth_node); |
| } |
| |
| if (prueth->pdata.quirk_10m_link_issue) |
| icss_iep_exit_fw(prueth->iep1); |
| |
| icss_iep_put(prueth->iep1); |
| icss_iep_put(prueth->iep0); |
| |
| gen_pool_free(prueth->sram_pool, |
| (unsigned long)prueth->msmcram.va, |
| MSMC_RAM_SIZE); |
| |
| pruss_release_mem_region(prueth->pruss, &prueth->shram); |
| |
| pruss_put(prueth->pruss); |
| |
| if (prueth->eth_node[PRUETH_MAC1]) |
| prueth_put_cores(prueth, ICSS_SLICE1); |
| |
| if (prueth->eth_node[PRUETH_MAC0]) |
| prueth_put_cores(prueth, ICSS_SLICE0); |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int prueth_suspend(struct device *dev) |
| { |
| struct prueth *prueth = dev_get_drvdata(dev); |
| struct net_device *ndev; |
| int i, ret; |
| |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| ndev = prueth->registered_netdevs[i]; |
| |
| if (!ndev) |
| continue; |
| |
| if (netif_running(ndev)) { |
| netif_device_detach(ndev); |
| ret = emac_ndo_stop(ndev); |
| if (ret < 0) { |
| netdev_err(ndev, "failed to stop: %d", ret); |
| return ret; |
| } |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int prueth_resume(struct device *dev) |
| { |
| struct prueth *prueth = dev_get_drvdata(dev); |
| struct net_device *ndev; |
| int i, ret; |
| |
| for (i = 0; i < PRUETH_NUM_MACS; i++) { |
| ndev = prueth->registered_netdevs[i]; |
| |
| if (!ndev) |
| continue; |
| |
| if (netif_running(ndev)) { |
| ret = emac_ndo_open(ndev); |
| if (ret < 0) { |
| netdev_err(ndev, "failed to start: %d", ret); |
| return ret; |
| } |
| netif_device_attach(ndev); |
| } |
| } |
| |
| return 0; |
| } |
| #endif /* CONFIG_PM_SLEEP */ |
| |
| static const struct dev_pm_ops prueth_dev_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(prueth_suspend, prueth_resume) |
| }; |
| |
| static const struct prueth_pdata am654_icssg_pdata = { |
| .fdqring_mode = K3_RINGACC_RING_MODE_MESSAGE, |
| .quirk_10m_link_issue = 1, |
| }; |
| |
| static const struct prueth_pdata am64x_icssg_pdata = { |
| .fdqring_mode = K3_RINGACC_RING_MODE_RING, |
| }; |
| |
| static const struct of_device_id prueth_dt_match[] = { |
| { .compatible = "ti,am654-icssg-prueth", .data = &am654_icssg_pdata }, |
| { .compatible = "ti,am642-icssg-prueth", .data = &am64x_icssg_pdata }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, prueth_dt_match); |
| |
| static struct platform_driver prueth_driver = { |
| .probe = prueth_probe, |
| .remove_new = prueth_remove, |
| .driver = { |
| .name = "icssg-prueth", |
| .of_match_table = prueth_dt_match, |
| .pm = &prueth_dev_pm_ops, |
| }, |
| }; |
| module_platform_driver(prueth_driver); |
| |
| MODULE_AUTHOR("Roger Quadros <rogerq@ti.com>"); |
| MODULE_AUTHOR("Md Danish Anwar <danishanwar@ti.com>"); |
| MODULE_DESCRIPTION("PRUSS ICSSG Ethernet Driver"); |
| MODULE_LICENSE("GPL"); |