| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Xilinx ZynqMP DPDMA Engine driver |
| * |
| * Copyright (C) 2015 - 2020 Xilinx, Inc. |
| * |
| * Author: Hyun Woo Kwon <hyun.kwon@xilinx.com> |
| */ |
| |
| #include <linux/bitfield.h> |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/debugfs.h> |
| #include <linux/delay.h> |
| #include <linux/dma/xilinx_dpdma.h> |
| #include <linux/dmaengine.h> |
| #include <linux/dmapool.h> |
| #include <linux/interrupt.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/of_dma.h> |
| #include <linux/platform_device.h> |
| #include <linux/sched.h> |
| #include <linux/slab.h> |
| #include <linux/spinlock.h> |
| #include <linux/wait.h> |
| |
| #include <dt-bindings/dma/xlnx-zynqmp-dpdma.h> |
| |
| #include "../dmaengine.h" |
| #include "../virt-dma.h" |
| |
| /* DPDMA registers */ |
| #define XILINX_DPDMA_ERR_CTRL 0x000 |
| #define XILINX_DPDMA_ISR 0x004 |
| #define XILINX_DPDMA_IMR 0x008 |
| #define XILINX_DPDMA_IEN 0x00c |
| #define XILINX_DPDMA_IDS 0x010 |
| #define XILINX_DPDMA_INTR_DESC_DONE(n) BIT((n) + 0) |
| #define XILINX_DPDMA_INTR_DESC_DONE_MASK GENMASK(5, 0) |
| #define XILINX_DPDMA_INTR_NO_OSTAND(n) BIT((n) + 6) |
| #define XILINX_DPDMA_INTR_NO_OSTAND_MASK GENMASK(11, 6) |
| #define XILINX_DPDMA_INTR_AXI_ERR(n) BIT((n) + 12) |
| #define XILINX_DPDMA_INTR_AXI_ERR_MASK GENMASK(17, 12) |
| #define XILINX_DPDMA_INTR_DESC_ERR(n) BIT((n) + 16) |
| #define XILINX_DPDMA_INTR_DESC_ERR_MASK GENMASK(23, 18) |
| #define XILINX_DPDMA_INTR_WR_CMD_FIFO_FULL BIT(24) |
| #define XILINX_DPDMA_INTR_WR_DATA_FIFO_FULL BIT(25) |
| #define XILINX_DPDMA_INTR_AXI_4K_CROSS BIT(26) |
| #define XILINX_DPDMA_INTR_VSYNC BIT(27) |
| #define XILINX_DPDMA_INTR_CHAN_ERR_MASK 0x00041000 |
| #define XILINX_DPDMA_INTR_CHAN_ERR 0x00fff000 |
| #define XILINX_DPDMA_INTR_GLOBAL_ERR 0x07000000 |
| #define XILINX_DPDMA_INTR_ERR_ALL 0x07fff000 |
| #define XILINX_DPDMA_INTR_CHAN_MASK 0x00041041 |
| #define XILINX_DPDMA_INTR_GLOBAL_MASK 0x0f000000 |
| #define XILINX_DPDMA_INTR_ALL 0x0fffffff |
| #define XILINX_DPDMA_EISR 0x014 |
| #define XILINX_DPDMA_EIMR 0x018 |
| #define XILINX_DPDMA_EIEN 0x01c |
| #define XILINX_DPDMA_EIDS 0x020 |
| #define XILINX_DPDMA_EINTR_INV_APB BIT(0) |
| #define XILINX_DPDMA_EINTR_RD_AXI_ERR(n) BIT((n) + 1) |
| #define XILINX_DPDMA_EINTR_RD_AXI_ERR_MASK GENMASK(6, 1) |
| #define XILINX_DPDMA_EINTR_PRE_ERR(n) BIT((n) + 7) |
| #define XILINX_DPDMA_EINTR_PRE_ERR_MASK GENMASK(12, 7) |
| #define XILINX_DPDMA_EINTR_CRC_ERR(n) BIT((n) + 13) |
| #define XILINX_DPDMA_EINTR_CRC_ERR_MASK GENMASK(18, 13) |
| #define XILINX_DPDMA_EINTR_WR_AXI_ERR(n) BIT((n) + 19) |
| #define XILINX_DPDMA_EINTR_WR_AXI_ERR_MASK GENMASK(24, 19) |
| #define XILINX_DPDMA_EINTR_DESC_DONE_ERR(n) BIT((n) + 25) |
| #define XILINX_DPDMA_EINTR_DESC_DONE_ERR_MASK GENMASK(30, 25) |
| #define XILINX_DPDMA_EINTR_RD_CMD_FIFO_FULL BIT(32) |
| #define XILINX_DPDMA_EINTR_CHAN_ERR_MASK 0x02082082 |
| #define XILINX_DPDMA_EINTR_CHAN_ERR 0x7ffffffe |
| #define XILINX_DPDMA_EINTR_GLOBAL_ERR 0x80000001 |
| #define XILINX_DPDMA_EINTR_ALL 0xffffffff |
| #define XILINX_DPDMA_CNTL 0x100 |
| #define XILINX_DPDMA_GBL 0x104 |
| #define XILINX_DPDMA_GBL_TRIG_MASK(n) ((n) << 0) |
| #define XILINX_DPDMA_GBL_RETRIG_MASK(n) ((n) << 6) |
| #define XILINX_DPDMA_ALC0_CNTL 0x108 |
| #define XILINX_DPDMA_ALC0_STATUS 0x10c |
| #define XILINX_DPDMA_ALC0_MAX 0x110 |
| #define XILINX_DPDMA_ALC0_MIN 0x114 |
| #define XILINX_DPDMA_ALC0_ACC 0x118 |
| #define XILINX_DPDMA_ALC0_ACC_TRAN 0x11c |
| #define XILINX_DPDMA_ALC1_CNTL 0x120 |
| #define XILINX_DPDMA_ALC1_STATUS 0x124 |
| #define XILINX_DPDMA_ALC1_MAX 0x128 |
| #define XILINX_DPDMA_ALC1_MIN 0x12c |
| #define XILINX_DPDMA_ALC1_ACC 0x130 |
| #define XILINX_DPDMA_ALC1_ACC_TRAN 0x134 |
| |
| /* Channel register */ |
| #define XILINX_DPDMA_CH_BASE 0x200 |
| #define XILINX_DPDMA_CH_OFFSET 0x100 |
| #define XILINX_DPDMA_CH_DESC_START_ADDRE 0x000 |
| #define XILINX_DPDMA_CH_DESC_START_ADDRE_MASK GENMASK(15, 0) |
| #define XILINX_DPDMA_CH_DESC_START_ADDR 0x004 |
| #define XILINX_DPDMA_CH_DESC_NEXT_ADDRE 0x008 |
| #define XILINX_DPDMA_CH_DESC_NEXT_ADDR 0x00c |
| #define XILINX_DPDMA_CH_PYLD_CUR_ADDRE 0x010 |
| #define XILINX_DPDMA_CH_PYLD_CUR_ADDR 0x014 |
| #define XILINX_DPDMA_CH_CNTL 0x018 |
| #define XILINX_DPDMA_CH_CNTL_ENABLE BIT(0) |
| #define XILINX_DPDMA_CH_CNTL_PAUSE BIT(1) |
| #define XILINX_DPDMA_CH_CNTL_QOS_DSCR_WR_MASK GENMASK(5, 2) |
| #define XILINX_DPDMA_CH_CNTL_QOS_DSCR_RD_MASK GENMASK(9, 6) |
| #define XILINX_DPDMA_CH_CNTL_QOS_DATA_RD_MASK GENMASK(13, 10) |
| #define XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS 11 |
| #define XILINX_DPDMA_CH_STATUS 0x01c |
| #define XILINX_DPDMA_CH_STATUS_OTRAN_CNT_MASK GENMASK(24, 21) |
| #define XILINX_DPDMA_CH_VDO 0x020 |
| #define XILINX_DPDMA_CH_PYLD_SZ 0x024 |
| #define XILINX_DPDMA_CH_DESC_ID 0x028 |
| #define XILINX_DPDMA_CH_DESC_ID_MASK GENMASK(15, 0) |
| |
| /* DPDMA descriptor fields */ |
| #define XILINX_DPDMA_DESC_CONTROL_PREEMBLE 0xa5 |
| #define XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR BIT(8) |
| #define XILINX_DPDMA_DESC_CONTROL_DESC_UPDATE BIT(9) |
| #define XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE BIT(10) |
| #define XILINX_DPDMA_DESC_CONTROL_FRAG_MODE BIT(18) |
| #define XILINX_DPDMA_DESC_CONTROL_LAST BIT(19) |
| #define XILINX_DPDMA_DESC_CONTROL_ENABLE_CRC BIT(20) |
| #define XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME BIT(21) |
| #define XILINX_DPDMA_DESC_ID_MASK GENMASK(15, 0) |
| #define XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK GENMASK(17, 0) |
| #define XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK GENMASK(31, 18) |
| #define XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK GENMASK(15, 0) |
| #define XILINX_DPDMA_DESC_ADDR_EXT_SRC_ADDR_MASK GENMASK(31, 16) |
| |
| #define XILINX_DPDMA_ALIGN_BYTES 256 |
| #define XILINX_DPDMA_LINESIZE_ALIGN_BITS 128 |
| |
| #define XILINX_DPDMA_NUM_CHAN 6 |
| |
| struct xilinx_dpdma_chan; |
| |
| /** |
| * struct xilinx_dpdma_hw_desc - DPDMA hardware descriptor |
| * @control: control configuration field |
| * @desc_id: descriptor ID |
| * @xfer_size: transfer size |
| * @hsize_stride: horizontal size and stride |
| * @timestamp_lsb: LSB of time stamp |
| * @timestamp_msb: MSB of time stamp |
| * @addr_ext: upper 16 bit of 48 bit address (next_desc and src_addr) |
| * @next_desc: next descriptor 32 bit address |
| * @src_addr: payload source address (1st page, 32 LSB) |
| * @addr_ext_23: payload source address (2nd and 3rd pages, 16 LSBs) |
| * @addr_ext_45: payload source address (4th and 5th pages, 16 LSBs) |
| * @src_addr2: payload source address (2nd page, 32 LSB) |
| * @src_addr3: payload source address (3rd page, 32 LSB) |
| * @src_addr4: payload source address (4th page, 32 LSB) |
| * @src_addr5: payload source address (5th page, 32 LSB) |
| * @crc: descriptor CRC |
| */ |
| struct xilinx_dpdma_hw_desc { |
| u32 control; |
| u32 desc_id; |
| u32 xfer_size; |
| u32 hsize_stride; |
| u32 timestamp_lsb; |
| u32 timestamp_msb; |
| u32 addr_ext; |
| u32 next_desc; |
| u32 src_addr; |
| u32 addr_ext_23; |
| u32 addr_ext_45; |
| u32 src_addr2; |
| u32 src_addr3; |
| u32 src_addr4; |
| u32 src_addr5; |
| u32 crc; |
| } __aligned(XILINX_DPDMA_ALIGN_BYTES); |
| |
| /** |
| * struct xilinx_dpdma_sw_desc - DPDMA software descriptor |
| * @hw: DPDMA hardware descriptor |
| * @node: list node for software descriptors |
| * @dma_addr: DMA address of the software descriptor |
| */ |
| struct xilinx_dpdma_sw_desc { |
| struct xilinx_dpdma_hw_desc hw; |
| struct list_head node; |
| dma_addr_t dma_addr; |
| }; |
| |
| /** |
| * struct xilinx_dpdma_tx_desc - DPDMA transaction descriptor |
| * @vdesc: virtual DMA descriptor |
| * @chan: DMA channel |
| * @descriptors: list of software descriptors |
| * @error: an error has been detected with this descriptor |
| */ |
| struct xilinx_dpdma_tx_desc { |
| struct virt_dma_desc vdesc; |
| struct xilinx_dpdma_chan *chan; |
| struct list_head descriptors; |
| bool error; |
| }; |
| |
| #define to_dpdma_tx_desc(_desc) \ |
| container_of(_desc, struct xilinx_dpdma_tx_desc, vdesc) |
| |
| /** |
| * struct xilinx_dpdma_chan - DPDMA channel |
| * @vchan: virtual DMA channel |
| * @reg: register base address |
| * @id: channel ID |
| * @wait_to_stop: queue to wait for outstanding transactions before stopping |
| * @running: true if the channel is running |
| * @first_frame: flag for the first frame of stream |
| * @video_group: flag if multi-channel operation is needed for video channels |
| * @lock: lock to access struct xilinx_dpdma_chan. Must be taken before |
| * @vchan.lock, if both are to be held. |
| * @desc_pool: descriptor allocation pool |
| * @err_task: error IRQ bottom half handler |
| * @desc: References to descriptors being processed |
| * @desc.pending: Descriptor schedule to the hardware, pending execution |
| * @desc.active: Descriptor being executed by the hardware |
| * @xdev: DPDMA device |
| */ |
| struct xilinx_dpdma_chan { |
| struct virt_dma_chan vchan; |
| void __iomem *reg; |
| unsigned int id; |
| |
| wait_queue_head_t wait_to_stop; |
| bool running; |
| bool first_frame; |
| bool video_group; |
| |
| spinlock_t lock; /* lock to access struct xilinx_dpdma_chan */ |
| struct dma_pool *desc_pool; |
| struct tasklet_struct err_task; |
| |
| struct { |
| struct xilinx_dpdma_tx_desc *pending; |
| struct xilinx_dpdma_tx_desc *active; |
| } desc; |
| |
| struct xilinx_dpdma_device *xdev; |
| }; |
| |
| #define to_xilinx_chan(_chan) \ |
| container_of(_chan, struct xilinx_dpdma_chan, vchan.chan) |
| |
| /** |
| * struct xilinx_dpdma_device - DPDMA device |
| * @common: generic dma device structure |
| * @reg: register base address |
| * @dev: generic device structure |
| * @irq: the interrupt number |
| * @axi_clk: axi clock |
| * @chan: DPDMA channels |
| * @ext_addr: flag for 64 bit system (48 bit addressing) |
| */ |
| struct xilinx_dpdma_device { |
| struct dma_device common; |
| void __iomem *reg; |
| struct device *dev; |
| int irq; |
| |
| struct clk *axi_clk; |
| struct xilinx_dpdma_chan *chan[XILINX_DPDMA_NUM_CHAN]; |
| |
| bool ext_addr; |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * DebugFS |
| */ |
| #define XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE 32 |
| #define XILINX_DPDMA_DEBUGFS_UINT16_MAX_STR "65535" |
| |
| /* Match xilinx_dpdma_testcases vs dpdma_debugfs_reqs[] entry */ |
| enum xilinx_dpdma_testcases { |
| DPDMA_TC_INTR_DONE, |
| DPDMA_TC_NONE |
| }; |
| |
| struct xilinx_dpdma_debugfs { |
| enum xilinx_dpdma_testcases testcase; |
| u16 xilinx_dpdma_irq_done_count; |
| unsigned int chan_id; |
| }; |
| |
| static struct xilinx_dpdma_debugfs dpdma_debugfs; |
| struct xilinx_dpdma_debugfs_request { |
| const char *name; |
| enum xilinx_dpdma_testcases tc; |
| ssize_t (*read)(char *buf); |
| int (*write)(char *args); |
| }; |
| |
| static void xilinx_dpdma_debugfs_desc_done_irq(struct xilinx_dpdma_chan *chan) |
| { |
| if (IS_ENABLED(CONFIG_DEBUG_FS) && chan->id == dpdma_debugfs.chan_id) |
| dpdma_debugfs.xilinx_dpdma_irq_done_count++; |
| } |
| |
| static ssize_t xilinx_dpdma_debugfs_desc_done_irq_read(char *buf) |
| { |
| size_t out_str_len; |
| |
| dpdma_debugfs.testcase = DPDMA_TC_NONE; |
| |
| out_str_len = strlen(XILINX_DPDMA_DEBUGFS_UINT16_MAX_STR); |
| out_str_len = min_t(size_t, XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE, |
| out_str_len + 1); |
| snprintf(buf, out_str_len, "%d", |
| dpdma_debugfs.xilinx_dpdma_irq_done_count); |
| |
| return 0; |
| } |
| |
| static int xilinx_dpdma_debugfs_desc_done_irq_write(char *args) |
| { |
| char *arg; |
| int ret; |
| u32 id; |
| |
| arg = strsep(&args, " "); |
| if (!arg || strncasecmp(arg, "start", 5)) |
| return -EINVAL; |
| |
| arg = strsep(&args, " "); |
| if (!arg) |
| return -EINVAL; |
| |
| ret = kstrtou32(arg, 0, &id); |
| if (ret < 0) |
| return ret; |
| |
| if (id < ZYNQMP_DPDMA_VIDEO0 || id > ZYNQMP_DPDMA_AUDIO1) |
| return -EINVAL; |
| |
| dpdma_debugfs.testcase = DPDMA_TC_INTR_DONE; |
| dpdma_debugfs.xilinx_dpdma_irq_done_count = 0; |
| dpdma_debugfs.chan_id = id; |
| |
| return 0; |
| } |
| |
| /* Match xilinx_dpdma_testcases vs dpdma_debugfs_reqs[] entry */ |
| static struct xilinx_dpdma_debugfs_request dpdma_debugfs_reqs[] = { |
| { |
| .name = "DESCRIPTOR_DONE_INTR", |
| .tc = DPDMA_TC_INTR_DONE, |
| .read = xilinx_dpdma_debugfs_desc_done_irq_read, |
| .write = xilinx_dpdma_debugfs_desc_done_irq_write, |
| }, |
| }; |
| |
| static ssize_t xilinx_dpdma_debugfs_read(struct file *f, char __user *buf, |
| size_t size, loff_t *pos) |
| { |
| enum xilinx_dpdma_testcases testcase; |
| char *kern_buff; |
| int ret = 0; |
| |
| if (*pos != 0 || size <= 0) |
| return -EINVAL; |
| |
| kern_buff = kzalloc(XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE, GFP_KERNEL); |
| if (!kern_buff) { |
| dpdma_debugfs.testcase = DPDMA_TC_NONE; |
| return -ENOMEM; |
| } |
| |
| testcase = READ_ONCE(dpdma_debugfs.testcase); |
| if (testcase != DPDMA_TC_NONE) { |
| ret = dpdma_debugfs_reqs[testcase].read(kern_buff); |
| if (ret < 0) |
| goto done; |
| } else { |
| strscpy(kern_buff, "No testcase executed", |
| XILINX_DPDMA_DEBUGFS_READ_MAX_SIZE); |
| } |
| |
| size = min(size, strlen(kern_buff)); |
| if (copy_to_user(buf, kern_buff, size)) |
| ret = -EFAULT; |
| |
| done: |
| kfree(kern_buff); |
| if (ret) |
| return ret; |
| |
| *pos = size + 1; |
| return size; |
| } |
| |
| static ssize_t xilinx_dpdma_debugfs_write(struct file *f, |
| const char __user *buf, size_t size, |
| loff_t *pos) |
| { |
| char *kern_buff, *kern_buff_start; |
| char *testcase; |
| unsigned int i; |
| int ret; |
| |
| if (*pos != 0 || size <= 0) |
| return -EINVAL; |
| |
| /* Supporting single instance of test as of now. */ |
| if (dpdma_debugfs.testcase != DPDMA_TC_NONE) |
| return -EBUSY; |
| |
| kern_buff = kzalloc(size, GFP_KERNEL); |
| if (!kern_buff) |
| return -ENOMEM; |
| kern_buff_start = kern_buff; |
| |
| ret = strncpy_from_user(kern_buff, buf, size); |
| if (ret < 0) |
| goto done; |
| |
| /* Read the testcase name from a user request. */ |
| testcase = strsep(&kern_buff, " "); |
| |
| for (i = 0; i < ARRAY_SIZE(dpdma_debugfs_reqs); i++) { |
| if (!strcasecmp(testcase, dpdma_debugfs_reqs[i].name)) |
| break; |
| } |
| |
| if (i == ARRAY_SIZE(dpdma_debugfs_reqs)) { |
| ret = -EINVAL; |
| goto done; |
| } |
| |
| ret = dpdma_debugfs_reqs[i].write(kern_buff); |
| if (ret < 0) |
| goto done; |
| |
| ret = size; |
| |
| done: |
| kfree(kern_buff_start); |
| return ret; |
| } |
| |
| static const struct file_operations fops_xilinx_dpdma_dbgfs = { |
| .owner = THIS_MODULE, |
| .read = xilinx_dpdma_debugfs_read, |
| .write = xilinx_dpdma_debugfs_write, |
| }; |
| |
| static void xilinx_dpdma_debugfs_init(struct xilinx_dpdma_device *xdev) |
| { |
| struct dentry *dent; |
| |
| dpdma_debugfs.testcase = DPDMA_TC_NONE; |
| |
| dent = debugfs_create_file("testcase", 0444, xdev->common.dbg_dev_root, |
| NULL, &fops_xilinx_dpdma_dbgfs); |
| if (IS_ERR(dent)) |
| dev_err(xdev->dev, "Failed to create debugfs testcase file\n"); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * I/O Accessors |
| */ |
| |
| static inline u32 dpdma_read(void __iomem *base, u32 offset) |
| { |
| return ioread32(base + offset); |
| } |
| |
| static inline void dpdma_write(void __iomem *base, u32 offset, u32 val) |
| { |
| iowrite32(val, base + offset); |
| } |
| |
| static inline void dpdma_clr(void __iomem *base, u32 offset, u32 clr) |
| { |
| dpdma_write(base, offset, dpdma_read(base, offset) & ~clr); |
| } |
| |
| static inline void dpdma_set(void __iomem *base, u32 offset, u32 set) |
| { |
| dpdma_write(base, offset, dpdma_read(base, offset) | set); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Descriptor Operations |
| */ |
| |
| /** |
| * xilinx_dpdma_sw_desc_set_dma_addrs - Set DMA addresses in the descriptor |
| * @xdev: DPDMA device |
| * @sw_desc: The software descriptor in which to set DMA addresses |
| * @prev: The previous descriptor |
| * @dma_addr: array of dma addresses |
| * @num_src_addr: number of addresses in @dma_addr |
| * |
| * Set all the DMA addresses in the hardware descriptor corresponding to @dev |
| * from @dma_addr. If a previous descriptor is specified in @prev, its next |
| * descriptor DMA address is set to the DMA address of @sw_desc. @prev may be |
| * identical to @sw_desc for cyclic transfers. |
| */ |
| static void xilinx_dpdma_sw_desc_set_dma_addrs(struct xilinx_dpdma_device *xdev, |
| struct xilinx_dpdma_sw_desc *sw_desc, |
| struct xilinx_dpdma_sw_desc *prev, |
| dma_addr_t dma_addr[], |
| unsigned int num_src_addr) |
| { |
| struct xilinx_dpdma_hw_desc *hw_desc = &sw_desc->hw; |
| unsigned int i; |
| |
| hw_desc->src_addr = lower_32_bits(dma_addr[0]); |
| if (xdev->ext_addr) |
| hw_desc->addr_ext |= |
| FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_SRC_ADDR_MASK, |
| upper_32_bits(dma_addr[0])); |
| |
| for (i = 1; i < num_src_addr; i++) { |
| u32 *addr = &hw_desc->src_addr2; |
| |
| addr[i - 1] = lower_32_bits(dma_addr[i]); |
| |
| if (xdev->ext_addr) { |
| u32 *addr_ext = &hw_desc->addr_ext_23; |
| u32 addr_msb; |
| |
| addr_msb = upper_32_bits(dma_addr[i]) & GENMASK(15, 0); |
| addr_msb <<= 16 * ((i - 1) % 2); |
| addr_ext[(i - 1) / 2] |= addr_msb; |
| } |
| } |
| |
| if (!prev) |
| return; |
| |
| prev->hw.next_desc = lower_32_bits(sw_desc->dma_addr); |
| if (xdev->ext_addr) |
| prev->hw.addr_ext |= |
| FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK, |
| upper_32_bits(sw_desc->dma_addr)); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_alloc_sw_desc - Allocate a software descriptor |
| * @chan: DPDMA channel |
| * |
| * Allocate a software descriptor from the channel's descriptor pool. |
| * |
| * Return: a software descriptor or NULL. |
| */ |
| static struct xilinx_dpdma_sw_desc * |
| xilinx_dpdma_chan_alloc_sw_desc(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_sw_desc *sw_desc; |
| dma_addr_t dma_addr; |
| |
| sw_desc = dma_pool_zalloc(chan->desc_pool, GFP_ATOMIC, &dma_addr); |
| if (!sw_desc) |
| return NULL; |
| |
| sw_desc->dma_addr = dma_addr; |
| |
| return sw_desc; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_free_sw_desc - Free a software descriptor |
| * @chan: DPDMA channel |
| * @sw_desc: software descriptor to free |
| * |
| * Free a software descriptor from the channel's descriptor pool. |
| */ |
| static void |
| xilinx_dpdma_chan_free_sw_desc(struct xilinx_dpdma_chan *chan, |
| struct xilinx_dpdma_sw_desc *sw_desc) |
| { |
| dma_pool_free(chan->desc_pool, sw_desc, sw_desc->dma_addr); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_dump_tx_desc - Dump a tx descriptor |
| * @chan: DPDMA channel |
| * @tx_desc: tx descriptor to dump |
| * |
| * Dump contents of a tx descriptor |
| */ |
| static void xilinx_dpdma_chan_dump_tx_desc(struct xilinx_dpdma_chan *chan, |
| struct xilinx_dpdma_tx_desc *tx_desc) |
| { |
| struct xilinx_dpdma_sw_desc *sw_desc; |
| struct device *dev = chan->xdev->dev; |
| unsigned int i = 0; |
| |
| dev_dbg(dev, "------- TX descriptor dump start -------\n"); |
| dev_dbg(dev, "------- channel ID = %d -------\n", chan->id); |
| |
| list_for_each_entry(sw_desc, &tx_desc->descriptors, node) { |
| struct xilinx_dpdma_hw_desc *hw_desc = &sw_desc->hw; |
| |
| dev_dbg(dev, "------- HW descriptor %d -------\n", i++); |
| dev_dbg(dev, "descriptor DMA addr: %pad\n", &sw_desc->dma_addr); |
| dev_dbg(dev, "control: 0x%08x\n", hw_desc->control); |
| dev_dbg(dev, "desc_id: 0x%08x\n", hw_desc->desc_id); |
| dev_dbg(dev, "xfer_size: 0x%08x\n", hw_desc->xfer_size); |
| dev_dbg(dev, "hsize_stride: 0x%08x\n", hw_desc->hsize_stride); |
| dev_dbg(dev, "timestamp_lsb: 0x%08x\n", hw_desc->timestamp_lsb); |
| dev_dbg(dev, "timestamp_msb: 0x%08x\n", hw_desc->timestamp_msb); |
| dev_dbg(dev, "addr_ext: 0x%08x\n", hw_desc->addr_ext); |
| dev_dbg(dev, "next_desc: 0x%08x\n", hw_desc->next_desc); |
| dev_dbg(dev, "src_addr: 0x%08x\n", hw_desc->src_addr); |
| dev_dbg(dev, "addr_ext_23: 0x%08x\n", hw_desc->addr_ext_23); |
| dev_dbg(dev, "addr_ext_45: 0x%08x\n", hw_desc->addr_ext_45); |
| dev_dbg(dev, "src_addr2: 0x%08x\n", hw_desc->src_addr2); |
| dev_dbg(dev, "src_addr3: 0x%08x\n", hw_desc->src_addr3); |
| dev_dbg(dev, "src_addr4: 0x%08x\n", hw_desc->src_addr4); |
| dev_dbg(dev, "src_addr5: 0x%08x\n", hw_desc->src_addr5); |
| dev_dbg(dev, "crc: 0x%08x\n", hw_desc->crc); |
| } |
| |
| dev_dbg(dev, "------- TX descriptor dump end -------\n"); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_alloc_tx_desc - Allocate a transaction descriptor |
| * @chan: DPDMA channel |
| * |
| * Allocate a tx descriptor. |
| * |
| * Return: a tx descriptor or NULL. |
| */ |
| static struct xilinx_dpdma_tx_desc * |
| xilinx_dpdma_chan_alloc_tx_desc(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_tx_desc *tx_desc; |
| |
| tx_desc = kzalloc(sizeof(*tx_desc), GFP_NOWAIT); |
| if (!tx_desc) |
| return NULL; |
| |
| INIT_LIST_HEAD(&tx_desc->descriptors); |
| tx_desc->chan = chan; |
| tx_desc->error = false; |
| |
| return tx_desc; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_free_tx_desc - Free a virtual DMA descriptor |
| * @vdesc: virtual DMA descriptor |
| * |
| * Free the virtual DMA descriptor @vdesc including its software descriptors. |
| */ |
| static void xilinx_dpdma_chan_free_tx_desc(struct virt_dma_desc *vdesc) |
| { |
| struct xilinx_dpdma_sw_desc *sw_desc, *next; |
| struct xilinx_dpdma_tx_desc *desc; |
| |
| if (!vdesc) |
| return; |
| |
| desc = to_dpdma_tx_desc(vdesc); |
| |
| list_for_each_entry_safe(sw_desc, next, &desc->descriptors, node) { |
| list_del(&sw_desc->node); |
| xilinx_dpdma_chan_free_sw_desc(desc->chan, sw_desc); |
| } |
| |
| kfree(desc); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_prep_cyclic - Prepare a cyclic dma descriptor |
| * @chan: DPDMA channel |
| * @buf_addr: buffer address |
| * @buf_len: buffer length |
| * @period_len: number of periods |
| * @flags: tx flags argument passed in to prepare function |
| * |
| * Prepare a tx descriptor incudling internal software/hardware descriptors |
| * for the given cyclic transaction. |
| * |
| * Return: A dma async tx descriptor on success, or NULL. |
| */ |
| static struct dma_async_tx_descriptor * |
| xilinx_dpdma_chan_prep_cyclic(struct xilinx_dpdma_chan *chan, |
| dma_addr_t buf_addr, size_t buf_len, |
| size_t period_len, unsigned long flags) |
| { |
| struct xilinx_dpdma_tx_desc *tx_desc; |
| struct xilinx_dpdma_sw_desc *sw_desc, *last = NULL; |
| unsigned int periods = buf_len / period_len; |
| unsigned int i; |
| |
| tx_desc = xilinx_dpdma_chan_alloc_tx_desc(chan); |
| if (!tx_desc) |
| return NULL; |
| |
| for (i = 0; i < periods; i++) { |
| struct xilinx_dpdma_hw_desc *hw_desc; |
| |
| if (!IS_ALIGNED(buf_addr, XILINX_DPDMA_ALIGN_BYTES)) { |
| dev_err(chan->xdev->dev, |
| "buffer should be aligned at %d B\n", |
| XILINX_DPDMA_ALIGN_BYTES); |
| goto error; |
| } |
| |
| sw_desc = xilinx_dpdma_chan_alloc_sw_desc(chan); |
| if (!sw_desc) |
| goto error; |
| |
| xilinx_dpdma_sw_desc_set_dma_addrs(chan->xdev, sw_desc, last, |
| &buf_addr, 1); |
| hw_desc = &sw_desc->hw; |
| hw_desc->xfer_size = period_len; |
| hw_desc->hsize_stride = |
| FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK, |
| period_len) | |
| FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK, |
| period_len); |
| hw_desc->control = XILINX_DPDMA_DESC_CONTROL_PREEMBLE | |
| XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE | |
| XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR; |
| |
| list_add_tail(&sw_desc->node, &tx_desc->descriptors); |
| |
| buf_addr += period_len; |
| last = sw_desc; |
| } |
| |
| sw_desc = list_first_entry(&tx_desc->descriptors, |
| struct xilinx_dpdma_sw_desc, node); |
| last->hw.next_desc = lower_32_bits(sw_desc->dma_addr); |
| if (chan->xdev->ext_addr) |
| last->hw.addr_ext |= |
| FIELD_PREP(XILINX_DPDMA_DESC_ADDR_EXT_NEXT_ADDR_MASK, |
| upper_32_bits(sw_desc->dma_addr)); |
| |
| last->hw.control |= XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME; |
| |
| return vchan_tx_prep(&chan->vchan, &tx_desc->vdesc, flags); |
| |
| error: |
| xilinx_dpdma_chan_free_tx_desc(&tx_desc->vdesc); |
| |
| return NULL; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_prep_interleaved_dma - Prepare an interleaved dma |
| * descriptor |
| * @chan: DPDMA channel |
| * @xt: dma interleaved template |
| * |
| * Prepare a tx descriptor including internal software/hardware descriptors |
| * based on @xt. |
| * |
| * Return: A DPDMA TX descriptor on success, or NULL. |
| */ |
| static struct xilinx_dpdma_tx_desc * |
| xilinx_dpdma_chan_prep_interleaved_dma(struct xilinx_dpdma_chan *chan, |
| struct dma_interleaved_template *xt) |
| { |
| struct xilinx_dpdma_tx_desc *tx_desc; |
| struct xilinx_dpdma_sw_desc *sw_desc; |
| struct xilinx_dpdma_hw_desc *hw_desc; |
| size_t hsize = xt->sgl[0].size; |
| size_t stride = hsize + xt->sgl[0].icg; |
| |
| if (!IS_ALIGNED(xt->src_start, XILINX_DPDMA_ALIGN_BYTES)) { |
| dev_err(chan->xdev->dev, |
| "chan%u: buffer should be aligned at %d B\n", |
| chan->id, XILINX_DPDMA_ALIGN_BYTES); |
| return NULL; |
| } |
| |
| tx_desc = xilinx_dpdma_chan_alloc_tx_desc(chan); |
| if (!tx_desc) |
| return NULL; |
| |
| sw_desc = xilinx_dpdma_chan_alloc_sw_desc(chan); |
| if (!sw_desc) { |
| xilinx_dpdma_chan_free_tx_desc(&tx_desc->vdesc); |
| return NULL; |
| } |
| |
| xilinx_dpdma_sw_desc_set_dma_addrs(chan->xdev, sw_desc, sw_desc, |
| &xt->src_start, 1); |
| |
| hw_desc = &sw_desc->hw; |
| hsize = ALIGN(hsize, XILINX_DPDMA_LINESIZE_ALIGN_BITS / 8); |
| hw_desc->xfer_size = hsize * xt->numf; |
| hw_desc->hsize_stride = |
| FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_HSIZE_MASK, hsize) | |
| FIELD_PREP(XILINX_DPDMA_DESC_HSIZE_STRIDE_STRIDE_MASK, |
| stride / 16); |
| hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_PREEMBLE; |
| hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_COMPLETE_INTR; |
| hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_IGNORE_DONE; |
| hw_desc->control |= XILINX_DPDMA_DESC_CONTROL_LAST_OF_FRAME; |
| |
| list_add_tail(&sw_desc->node, &tx_desc->descriptors); |
| |
| return tx_desc; |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * DPDMA Channel Operations |
| */ |
| |
| /** |
| * xilinx_dpdma_chan_enable - Enable the channel |
| * @chan: DPDMA channel |
| * |
| * Enable the channel and its interrupts. Set the QoS values for video class. |
| */ |
| static void xilinx_dpdma_chan_enable(struct xilinx_dpdma_chan *chan) |
| { |
| u32 reg; |
| |
| reg = (XILINX_DPDMA_INTR_CHAN_MASK << chan->id) |
| | XILINX_DPDMA_INTR_GLOBAL_MASK; |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, reg); |
| reg = (XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id) |
| | XILINX_DPDMA_INTR_GLOBAL_ERR; |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_EIEN, reg); |
| |
| reg = XILINX_DPDMA_CH_CNTL_ENABLE |
| | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DSCR_WR_MASK, |
| XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS) |
| | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DSCR_RD_MASK, |
| XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS) |
| | FIELD_PREP(XILINX_DPDMA_CH_CNTL_QOS_DATA_RD_MASK, |
| XILINX_DPDMA_CH_CNTL_QOS_VID_CLASS); |
| dpdma_set(chan->reg, XILINX_DPDMA_CH_CNTL, reg); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_disable - Disable the channel |
| * @chan: DPDMA channel |
| * |
| * Disable the channel and its interrupts. |
| */ |
| static void xilinx_dpdma_chan_disable(struct xilinx_dpdma_chan *chan) |
| { |
| u32 reg; |
| |
| reg = XILINX_DPDMA_INTR_CHAN_MASK << chan->id; |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, reg); |
| reg = XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id; |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_EIEN, reg); |
| |
| dpdma_clr(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_ENABLE); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_pause - Pause the channel |
| * @chan: DPDMA channel |
| * |
| * Pause the channel. |
| */ |
| static void xilinx_dpdma_chan_pause(struct xilinx_dpdma_chan *chan) |
| { |
| dpdma_set(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_PAUSE); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_unpause - Unpause the channel |
| * @chan: DPDMA channel |
| * |
| * Unpause the channel. |
| */ |
| static void xilinx_dpdma_chan_unpause(struct xilinx_dpdma_chan *chan) |
| { |
| dpdma_clr(chan->reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_PAUSE); |
| } |
| |
| static u32 xilinx_dpdma_chan_video_group_ready(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_device *xdev = chan->xdev; |
| u32 channels = 0; |
| unsigned int i; |
| |
| for (i = ZYNQMP_DPDMA_VIDEO0; i <= ZYNQMP_DPDMA_VIDEO2; i++) { |
| if (xdev->chan[i]->video_group && !xdev->chan[i]->running) |
| return 0; |
| |
| if (xdev->chan[i]->video_group) |
| channels |= BIT(i); |
| } |
| |
| return channels; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_queue_transfer - Queue the next transfer |
| * @chan: DPDMA channel |
| * |
| * Queue the next descriptor, if any, to the hardware. If the channel is |
| * stopped, start it first. Otherwise retrigger it with the next descriptor. |
| */ |
| static void xilinx_dpdma_chan_queue_transfer(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_device *xdev = chan->xdev; |
| struct xilinx_dpdma_sw_desc *sw_desc; |
| struct xilinx_dpdma_tx_desc *desc; |
| struct virt_dma_desc *vdesc; |
| u32 reg, channels; |
| bool first_frame; |
| |
| lockdep_assert_held(&chan->lock); |
| |
| if (chan->desc.pending) |
| return; |
| |
| if (!chan->running) { |
| xilinx_dpdma_chan_unpause(chan); |
| xilinx_dpdma_chan_enable(chan); |
| chan->first_frame = true; |
| chan->running = true; |
| } |
| |
| vdesc = vchan_next_desc(&chan->vchan); |
| if (!vdesc) |
| return; |
| |
| desc = to_dpdma_tx_desc(vdesc); |
| chan->desc.pending = desc; |
| list_del(&desc->vdesc.node); |
| |
| /* |
| * Assign the cookie to descriptors in this transaction. Only 16 bit |
| * will be used, but it should be enough. |
| */ |
| list_for_each_entry(sw_desc, &desc->descriptors, node) |
| sw_desc->hw.desc_id = desc->vdesc.tx.cookie |
| & XILINX_DPDMA_CH_DESC_ID_MASK; |
| |
| sw_desc = list_first_entry(&desc->descriptors, |
| struct xilinx_dpdma_sw_desc, node); |
| dpdma_write(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDR, |
| lower_32_bits(sw_desc->dma_addr)); |
| if (xdev->ext_addr) |
| dpdma_write(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDRE, |
| FIELD_PREP(XILINX_DPDMA_CH_DESC_START_ADDRE_MASK, |
| upper_32_bits(sw_desc->dma_addr))); |
| |
| first_frame = chan->first_frame; |
| chan->first_frame = false; |
| |
| if (chan->video_group) { |
| channels = xilinx_dpdma_chan_video_group_ready(chan); |
| /* |
| * Trigger the transfer only when all channels in the group are |
| * ready. |
| */ |
| if (!channels) |
| return; |
| } else { |
| channels = BIT(chan->id); |
| } |
| |
| if (first_frame) |
| reg = XILINX_DPDMA_GBL_TRIG_MASK(channels); |
| else |
| reg = XILINX_DPDMA_GBL_RETRIG_MASK(channels); |
| |
| dpdma_write(xdev->reg, XILINX_DPDMA_GBL, reg); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_ostand - Number of outstanding transactions |
| * @chan: DPDMA channel |
| * |
| * Read and return the number of outstanding transactions from register. |
| * |
| * Return: Number of outstanding transactions from the status register. |
| */ |
| static u32 xilinx_dpdma_chan_ostand(struct xilinx_dpdma_chan *chan) |
| { |
| return FIELD_GET(XILINX_DPDMA_CH_STATUS_OTRAN_CNT_MASK, |
| dpdma_read(chan->reg, XILINX_DPDMA_CH_STATUS)); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_notify_no_ostand - Notify no outstanding transaction event |
| * @chan: DPDMA channel |
| * |
| * Notify waiters for no outstanding event, so waiters can stop the channel |
| * safely. This function is supposed to be called when 'no outstanding' |
| * interrupt is generated. The 'no outstanding' interrupt is disabled and |
| * should be re-enabled when this event is handled. If the channel status |
| * register still shows some number of outstanding transactions, the interrupt |
| * remains enabled. |
| * |
| * Return: 0 on success. On failure, -EWOULDBLOCK if there's still outstanding |
| * transaction(s). |
| */ |
| static int xilinx_dpdma_chan_notify_no_ostand(struct xilinx_dpdma_chan *chan) |
| { |
| u32 cnt; |
| |
| cnt = xilinx_dpdma_chan_ostand(chan); |
| if (cnt) { |
| dev_dbg(chan->xdev->dev, |
| "chan%u: %d outstanding transactions\n", |
| chan->id, cnt); |
| return -EWOULDBLOCK; |
| } |
| |
| /* Disable 'no outstanding' interrupt */ |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_IDS, |
| XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); |
| wake_up(&chan->wait_to_stop); |
| |
| return 0; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_wait_no_ostand - Wait for the no outstanding irq |
| * @chan: DPDMA channel |
| * |
| * Wait for the no outstanding transaction interrupt. This functions can sleep |
| * for 50ms. |
| * |
| * Return: 0 on success. On failure, -ETIMEOUT for time out, or the error code |
| * from wait_event_interruptible_timeout(). |
| */ |
| static int xilinx_dpdma_chan_wait_no_ostand(struct xilinx_dpdma_chan *chan) |
| { |
| int ret; |
| |
| /* Wait for a no outstanding transaction interrupt upto 50msec */ |
| ret = wait_event_interruptible_timeout(chan->wait_to_stop, |
| !xilinx_dpdma_chan_ostand(chan), |
| msecs_to_jiffies(50)); |
| if (ret > 0) { |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, |
| XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); |
| return 0; |
| } |
| |
| dev_err(chan->xdev->dev, "chan%u: not ready to stop: %d trans\n", |
| chan->id, xilinx_dpdma_chan_ostand(chan)); |
| |
| if (ret == 0) |
| return -ETIMEDOUT; |
| |
| return ret; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_poll_no_ostand - Poll the outstanding transaction status |
| * @chan: DPDMA channel |
| * |
| * Poll the outstanding transaction status, and return when there's no |
| * outstanding transaction. This functions can be used in the interrupt context |
| * or where the atomicity is required. Calling thread may wait more than 50ms. |
| * |
| * Return: 0 on success, or -ETIMEDOUT. |
| */ |
| static int xilinx_dpdma_chan_poll_no_ostand(struct xilinx_dpdma_chan *chan) |
| { |
| u32 cnt, loop = 50000; |
| |
| /* Poll at least for 50ms (20 fps). */ |
| do { |
| cnt = xilinx_dpdma_chan_ostand(chan); |
| udelay(1); |
| } while (loop-- > 0 && cnt); |
| |
| if (loop) { |
| dpdma_write(chan->xdev->reg, XILINX_DPDMA_IEN, |
| XILINX_DPDMA_INTR_NO_OSTAND(chan->id)); |
| return 0; |
| } |
| |
| dev_err(chan->xdev->dev, "chan%u: not ready to stop: %d trans\n", |
| chan->id, xilinx_dpdma_chan_ostand(chan)); |
| |
| return -ETIMEDOUT; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_stop - Stop the channel |
| * @chan: DPDMA channel |
| * |
| * Stop a previously paused channel by first waiting for completion of all |
| * outstanding transaction and then disabling the channel. |
| * |
| * Return: 0 on success, or -ETIMEDOUT if the channel failed to stop. |
| */ |
| static int xilinx_dpdma_chan_stop(struct xilinx_dpdma_chan *chan) |
| { |
| unsigned long flags; |
| int ret; |
| |
| ret = xilinx_dpdma_chan_wait_no_ostand(chan); |
| if (ret) |
| return ret; |
| |
| spin_lock_irqsave(&chan->lock, flags); |
| xilinx_dpdma_chan_disable(chan); |
| chan->running = false; |
| spin_unlock_irqrestore(&chan->lock, flags); |
| |
| return 0; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_done_irq - Handle hardware descriptor completion |
| * @chan: DPDMA channel |
| * |
| * Handle completion of the currently active descriptor (@chan->desc.active). As |
| * we currently support cyclic transfers only, this just invokes the cyclic |
| * callback. The descriptor will be completed at the VSYNC interrupt when a new |
| * descriptor replaces it. |
| */ |
| static void xilinx_dpdma_chan_done_irq(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_tx_desc *active; |
| |
| spin_lock(&chan->lock); |
| |
| xilinx_dpdma_debugfs_desc_done_irq(chan); |
| |
| active = chan->desc.active; |
| if (active) |
| vchan_cyclic_callback(&active->vdesc); |
| else |
| dev_warn(chan->xdev->dev, |
| "chan%u: DONE IRQ with no active descriptor!\n", |
| chan->id); |
| |
| spin_unlock(&chan->lock); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_vsync_irq - Handle hardware descriptor scheduling |
| * @chan: DPDMA channel |
| * |
| * At VSYNC the active descriptor may have been replaced by the pending |
| * descriptor. Detect this through the DESC_ID and perform appropriate |
| * bookkeeping. |
| */ |
| static void xilinx_dpdma_chan_vsync_irq(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_tx_desc *pending; |
| struct xilinx_dpdma_sw_desc *sw_desc; |
| u32 desc_id; |
| |
| spin_lock(&chan->lock); |
| |
| pending = chan->desc.pending; |
| if (!chan->running || !pending) |
| goto out; |
| |
| desc_id = dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_ID) |
| & XILINX_DPDMA_CH_DESC_ID_MASK; |
| |
| /* If the retrigger raced with vsync, retry at the next frame. */ |
| sw_desc = list_first_entry(&pending->descriptors, |
| struct xilinx_dpdma_sw_desc, node); |
| if (sw_desc->hw.desc_id != desc_id) { |
| dev_dbg(chan->xdev->dev, |
| "chan%u: vsync race lost (%u != %u), retrying\n", |
| chan->id, sw_desc->hw.desc_id, desc_id); |
| goto out; |
| } |
| |
| /* |
| * Complete the active descriptor, if any, promote the pending |
| * descriptor to active, and queue the next transfer, if any. |
| */ |
| spin_lock(&chan->vchan.lock); |
| if (chan->desc.active) |
| vchan_cookie_complete(&chan->desc.active->vdesc); |
| chan->desc.active = pending; |
| chan->desc.pending = NULL; |
| |
| xilinx_dpdma_chan_queue_transfer(chan); |
| spin_unlock(&chan->vchan.lock); |
| |
| out: |
| spin_unlock(&chan->lock); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_err - Detect any channel error |
| * @chan: DPDMA channel |
| * @isr: masked Interrupt Status Register |
| * @eisr: Error Interrupt Status Register |
| * |
| * Return: true if any channel error occurs, or false otherwise. |
| */ |
| static bool |
| xilinx_dpdma_chan_err(struct xilinx_dpdma_chan *chan, u32 isr, u32 eisr) |
| { |
| if (!chan) |
| return false; |
| |
| if (chan->running && |
| ((isr & (XILINX_DPDMA_INTR_CHAN_ERR_MASK << chan->id)) || |
| (eisr & (XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id)))) |
| return true; |
| |
| return false; |
| } |
| |
| /** |
| * xilinx_dpdma_chan_handle_err - DPDMA channel error handling |
| * @chan: DPDMA channel |
| * |
| * This function is called when any channel error or any global error occurs. |
| * The function disables the paused channel by errors and determines |
| * if the current active descriptor can be rescheduled depending on |
| * the descriptor status. |
| */ |
| static void xilinx_dpdma_chan_handle_err(struct xilinx_dpdma_chan *chan) |
| { |
| struct xilinx_dpdma_device *xdev = chan->xdev; |
| struct xilinx_dpdma_tx_desc *active; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&chan->lock, flags); |
| |
| dev_dbg(xdev->dev, "chan%u: cur desc addr = 0x%04x%08x\n", |
| chan->id, |
| dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDRE), |
| dpdma_read(chan->reg, XILINX_DPDMA_CH_DESC_START_ADDR)); |
| dev_dbg(xdev->dev, "chan%u: cur payload addr = 0x%04x%08x\n", |
| chan->id, |
| dpdma_read(chan->reg, XILINX_DPDMA_CH_PYLD_CUR_ADDRE), |
| dpdma_read(chan->reg, XILINX_DPDMA_CH_PYLD_CUR_ADDR)); |
| |
| xilinx_dpdma_chan_disable(chan); |
| chan->running = false; |
| |
| if (!chan->desc.active) |
| goto out_unlock; |
| |
| active = chan->desc.active; |
| chan->desc.active = NULL; |
| |
| xilinx_dpdma_chan_dump_tx_desc(chan, active); |
| |
| if (active->error) |
| dev_dbg(xdev->dev, "chan%u: repeated error on desc\n", |
| chan->id); |
| |
| /* Reschedule if there's no new descriptor */ |
| if (!chan->desc.pending && |
| list_empty(&chan->vchan.desc_issued)) { |
| active->error = true; |
| list_add_tail(&active->vdesc.node, |
| &chan->vchan.desc_issued); |
| } else { |
| xilinx_dpdma_chan_free_tx_desc(&active->vdesc); |
| } |
| |
| out_unlock: |
| spin_unlock_irqrestore(&chan->lock, flags); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * DMA Engine Operations |
| */ |
| static struct dma_async_tx_descriptor * |
| xilinx_dpdma_prep_dma_cyclic(struct dma_chan *dchan, dma_addr_t buf_addr, |
| size_t buf_len, size_t period_len, |
| enum dma_transfer_direction direction, |
| unsigned long flags) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| |
| if (direction != DMA_MEM_TO_DEV) |
| return NULL; |
| |
| if (buf_len % period_len) |
| return NULL; |
| |
| return xilinx_dpdma_chan_prep_cyclic(chan, buf_addr, buf_len, |
| period_len, flags); |
| } |
| |
| static struct dma_async_tx_descriptor * |
| xilinx_dpdma_prep_interleaved_dma(struct dma_chan *dchan, |
| struct dma_interleaved_template *xt, |
| unsigned long flags) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| struct xilinx_dpdma_tx_desc *desc; |
| |
| if (xt->dir != DMA_MEM_TO_DEV) |
| return NULL; |
| |
| if (!xt->numf || !xt->sgl[0].size) |
| return NULL; |
| |
| if (!(flags & DMA_PREP_REPEAT) || !(flags & DMA_PREP_LOAD_EOT)) |
| return NULL; |
| |
| desc = xilinx_dpdma_chan_prep_interleaved_dma(chan, xt); |
| if (!desc) |
| return NULL; |
| |
| vchan_tx_prep(&chan->vchan, &desc->vdesc, flags | DMA_CTRL_ACK); |
| |
| return &desc->vdesc.tx; |
| } |
| |
| /** |
| * xilinx_dpdma_alloc_chan_resources - Allocate resources for the channel |
| * @dchan: DMA channel |
| * |
| * Allocate a descriptor pool for the channel. |
| * |
| * Return: 0 on success, or -ENOMEM if failed to allocate a pool. |
| */ |
| static int xilinx_dpdma_alloc_chan_resources(struct dma_chan *dchan) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| size_t align = __alignof__(struct xilinx_dpdma_sw_desc); |
| |
| chan->desc_pool = dma_pool_create(dev_name(chan->xdev->dev), |
| chan->xdev->dev, |
| sizeof(struct xilinx_dpdma_sw_desc), |
| align, 0); |
| if (!chan->desc_pool) { |
| dev_err(chan->xdev->dev, |
| "chan%u: failed to allocate a descriptor pool\n", |
| chan->id); |
| return -ENOMEM; |
| } |
| |
| return 0; |
| } |
| |
| /** |
| * xilinx_dpdma_free_chan_resources - Free all resources for the channel |
| * @dchan: DMA channel |
| * |
| * Free resources associated with the virtual DMA channel, and destroy the |
| * descriptor pool. |
| */ |
| static void xilinx_dpdma_free_chan_resources(struct dma_chan *dchan) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| |
| vchan_free_chan_resources(&chan->vchan); |
| |
| dma_pool_destroy(chan->desc_pool); |
| chan->desc_pool = NULL; |
| } |
| |
| static void xilinx_dpdma_issue_pending(struct dma_chan *dchan) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| unsigned long flags; |
| |
| spin_lock_irqsave(&chan->lock, flags); |
| spin_lock(&chan->vchan.lock); |
| if (vchan_issue_pending(&chan->vchan)) |
| xilinx_dpdma_chan_queue_transfer(chan); |
| spin_unlock(&chan->vchan.lock); |
| spin_unlock_irqrestore(&chan->lock, flags); |
| } |
| |
| static int xilinx_dpdma_config(struct dma_chan *dchan, |
| struct dma_slave_config *config) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| struct xilinx_dpdma_peripheral_config *pconfig; |
| unsigned long flags; |
| |
| /* |
| * The destination address doesn't need to be specified as the DPDMA is |
| * hardwired to the destination (the DP controller). The transfer |
| * width, burst size and port window size are thus meaningless, they're |
| * fixed both on the DPDMA side and on the DP controller side. |
| */ |
| |
| /* |
| * Use the peripheral_config to indicate that the channel is part |
| * of a video group. This requires matching use of the custom |
| * structure in each driver. |
| */ |
| pconfig = config->peripheral_config; |
| if (WARN_ON(pconfig && config->peripheral_size != sizeof(*pconfig))) |
| return -EINVAL; |
| |
| spin_lock_irqsave(&chan->lock, flags); |
| if (chan->id <= ZYNQMP_DPDMA_VIDEO2 && pconfig) |
| chan->video_group = pconfig->video_group; |
| spin_unlock_irqrestore(&chan->lock, flags); |
| |
| return 0; |
| } |
| |
| static int xilinx_dpdma_pause(struct dma_chan *dchan) |
| { |
| xilinx_dpdma_chan_pause(to_xilinx_chan(dchan)); |
| |
| return 0; |
| } |
| |
| static int xilinx_dpdma_resume(struct dma_chan *dchan) |
| { |
| xilinx_dpdma_chan_unpause(to_xilinx_chan(dchan)); |
| |
| return 0; |
| } |
| |
| /** |
| * xilinx_dpdma_terminate_all - Terminate the channel and descriptors |
| * @dchan: DMA channel |
| * |
| * Pause the channel without waiting for ongoing transfers to complete. Waiting |
| * for completion is performed by xilinx_dpdma_synchronize() that will disable |
| * the channel to complete the stop. |
| * |
| * All the descriptors associated with the channel that are guaranteed not to |
| * be touched by the hardware. The pending and active descriptor are not |
| * touched, and will be freed either upon completion, or by |
| * xilinx_dpdma_synchronize(). |
| * |
| * Return: 0 on success, or -ETIMEDOUT if the channel failed to stop. |
| */ |
| static int xilinx_dpdma_terminate_all(struct dma_chan *dchan) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| struct xilinx_dpdma_device *xdev = chan->xdev; |
| LIST_HEAD(descriptors); |
| unsigned long flags; |
| unsigned int i; |
| |
| /* Pause the channel (including the whole video group if applicable). */ |
| if (chan->video_group) { |
| for (i = ZYNQMP_DPDMA_VIDEO0; i <= ZYNQMP_DPDMA_VIDEO2; i++) { |
| if (xdev->chan[i]->video_group && |
| xdev->chan[i]->running) { |
| xilinx_dpdma_chan_pause(xdev->chan[i]); |
| xdev->chan[i]->video_group = false; |
| } |
| } |
| } else { |
| xilinx_dpdma_chan_pause(chan); |
| } |
| |
| /* Gather all the descriptors we can free and free them. */ |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| vchan_get_all_descriptors(&chan->vchan, &descriptors); |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| vchan_dma_desc_free_list(&chan->vchan, &descriptors); |
| |
| return 0; |
| } |
| |
| /** |
| * xilinx_dpdma_synchronize - Synchronize callback execution |
| * @dchan: DMA channel |
| * |
| * Synchronizing callback execution ensures that all previously issued |
| * transfers have completed and all associated callbacks have been called and |
| * have returned. |
| * |
| * This function waits for the DMA channel to stop. It assumes it has been |
| * paused by a previous call to dmaengine_terminate_async(), and that no new |
| * pending descriptors have been issued with dma_async_issue_pending(). The |
| * behaviour is undefined otherwise. |
| */ |
| static void xilinx_dpdma_synchronize(struct dma_chan *dchan) |
| { |
| struct xilinx_dpdma_chan *chan = to_xilinx_chan(dchan); |
| unsigned long flags; |
| |
| xilinx_dpdma_chan_stop(chan); |
| |
| spin_lock_irqsave(&chan->vchan.lock, flags); |
| if (chan->desc.pending) { |
| vchan_terminate_vdesc(&chan->desc.pending->vdesc); |
| chan->desc.pending = NULL; |
| } |
| if (chan->desc.active) { |
| vchan_terminate_vdesc(&chan->desc.active->vdesc); |
| chan->desc.active = NULL; |
| } |
| spin_unlock_irqrestore(&chan->vchan.lock, flags); |
| |
| vchan_synchronize(&chan->vchan); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Interrupt and Tasklet Handling |
| */ |
| |
| /** |
| * xilinx_dpdma_err - Detect any global error |
| * @isr: Interrupt Status Register |
| * @eisr: Error Interrupt Status Register |
| * |
| * Return: True if any global error occurs, or false otherwise. |
| */ |
| static bool xilinx_dpdma_err(u32 isr, u32 eisr) |
| { |
| if (isr & XILINX_DPDMA_INTR_GLOBAL_ERR || |
| eisr & XILINX_DPDMA_EINTR_GLOBAL_ERR) |
| return true; |
| |
| return false; |
| } |
| |
| /** |
| * xilinx_dpdma_handle_err_irq - Handle DPDMA error interrupt |
| * @xdev: DPDMA device |
| * @isr: masked Interrupt Status Register |
| * @eisr: Error Interrupt Status Register |
| * |
| * Handle if any error occurs based on @isr and @eisr. This function disables |
| * corresponding error interrupts, and those should be re-enabled once handling |
| * is done. |
| */ |
| static void xilinx_dpdma_handle_err_irq(struct xilinx_dpdma_device *xdev, |
| u32 isr, u32 eisr) |
| { |
| bool err = xilinx_dpdma_err(isr, eisr); |
| unsigned int i; |
| |
| dev_dbg_ratelimited(xdev->dev, |
| "error irq: isr = 0x%08x, eisr = 0x%08x\n", |
| isr, eisr); |
| |
| /* Disable channel error interrupts until errors are handled. */ |
| dpdma_write(xdev->reg, XILINX_DPDMA_IDS, |
| isr & ~XILINX_DPDMA_INTR_GLOBAL_ERR); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EIDS, |
| eisr & ~XILINX_DPDMA_EINTR_GLOBAL_ERR); |
| |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) |
| if (err || xilinx_dpdma_chan_err(xdev->chan[i], isr, eisr)) |
| tasklet_schedule(&xdev->chan[i]->err_task); |
| } |
| |
| /** |
| * xilinx_dpdma_enable_irq - Enable interrupts |
| * @xdev: DPDMA device |
| * |
| * Enable interrupts. |
| */ |
| static void xilinx_dpdma_enable_irq(struct xilinx_dpdma_device *xdev) |
| { |
| dpdma_write(xdev->reg, XILINX_DPDMA_IEN, XILINX_DPDMA_INTR_ALL); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EIEN, XILINX_DPDMA_EINTR_ALL); |
| } |
| |
| /** |
| * xilinx_dpdma_disable_irq - Disable interrupts |
| * @xdev: DPDMA device |
| * |
| * Disable interrupts. |
| */ |
| static void xilinx_dpdma_disable_irq(struct xilinx_dpdma_device *xdev) |
| { |
| dpdma_write(xdev->reg, XILINX_DPDMA_IDS, XILINX_DPDMA_INTR_ALL); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EIDS, XILINX_DPDMA_EINTR_ALL); |
| } |
| |
| /** |
| * xilinx_dpdma_chan_err_task - Per channel tasklet for error handling |
| * @t: pointer to the tasklet associated with this handler |
| * |
| * Per channel error handling tasklet. This function waits for the outstanding |
| * transaction to complete and triggers error handling. After error handling, |
| * re-enable channel error interrupts, and restart the channel if needed. |
| */ |
| static void xilinx_dpdma_chan_err_task(struct tasklet_struct *t) |
| { |
| struct xilinx_dpdma_chan *chan = from_tasklet(chan, t, err_task); |
| struct xilinx_dpdma_device *xdev = chan->xdev; |
| unsigned long flags; |
| |
| /* Proceed error handling even when polling fails. */ |
| xilinx_dpdma_chan_poll_no_ostand(chan); |
| |
| xilinx_dpdma_chan_handle_err(chan); |
| |
| dpdma_write(xdev->reg, XILINX_DPDMA_IEN, |
| XILINX_DPDMA_INTR_CHAN_ERR_MASK << chan->id); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EIEN, |
| XILINX_DPDMA_EINTR_CHAN_ERR_MASK << chan->id); |
| |
| spin_lock_irqsave(&chan->lock, flags); |
| spin_lock(&chan->vchan.lock); |
| xilinx_dpdma_chan_queue_transfer(chan); |
| spin_unlock(&chan->vchan.lock); |
| spin_unlock_irqrestore(&chan->lock, flags); |
| } |
| |
| static irqreturn_t xilinx_dpdma_irq_handler(int irq, void *data) |
| { |
| struct xilinx_dpdma_device *xdev = data; |
| unsigned long mask; |
| unsigned int i; |
| u32 status; |
| u32 error; |
| |
| status = dpdma_read(xdev->reg, XILINX_DPDMA_ISR); |
| error = dpdma_read(xdev->reg, XILINX_DPDMA_EISR); |
| if (!status && !error) |
| return IRQ_NONE; |
| |
| dpdma_write(xdev->reg, XILINX_DPDMA_ISR, status); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EISR, error); |
| |
| if (status & XILINX_DPDMA_INTR_VSYNC) { |
| /* |
| * There's a single VSYNC interrupt that needs to be processed |
| * by each running channel to update the active descriptor. |
| */ |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) { |
| struct xilinx_dpdma_chan *chan = xdev->chan[i]; |
| |
| if (chan) |
| xilinx_dpdma_chan_vsync_irq(chan); |
| } |
| } |
| |
| mask = FIELD_GET(XILINX_DPDMA_INTR_DESC_DONE_MASK, status); |
| if (mask) { |
| for_each_set_bit(i, &mask, ARRAY_SIZE(xdev->chan)) |
| xilinx_dpdma_chan_done_irq(xdev->chan[i]); |
| } |
| |
| mask = FIELD_GET(XILINX_DPDMA_INTR_NO_OSTAND_MASK, status); |
| if (mask) { |
| for_each_set_bit(i, &mask, ARRAY_SIZE(xdev->chan)) |
| xilinx_dpdma_chan_notify_no_ostand(xdev->chan[i]); |
| } |
| |
| mask = status & XILINX_DPDMA_INTR_ERR_ALL; |
| if (mask || error) |
| xilinx_dpdma_handle_err_irq(xdev, mask, error); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Initialization & Cleanup |
| */ |
| |
| static int xilinx_dpdma_chan_init(struct xilinx_dpdma_device *xdev, |
| unsigned int chan_id) |
| { |
| struct xilinx_dpdma_chan *chan; |
| |
| chan = devm_kzalloc(xdev->dev, sizeof(*chan), GFP_KERNEL); |
| if (!chan) |
| return -ENOMEM; |
| |
| chan->id = chan_id; |
| chan->reg = xdev->reg + XILINX_DPDMA_CH_BASE |
| + XILINX_DPDMA_CH_OFFSET * chan->id; |
| chan->running = false; |
| chan->xdev = xdev; |
| |
| spin_lock_init(&chan->lock); |
| init_waitqueue_head(&chan->wait_to_stop); |
| |
| tasklet_setup(&chan->err_task, xilinx_dpdma_chan_err_task); |
| |
| chan->vchan.desc_free = xilinx_dpdma_chan_free_tx_desc; |
| vchan_init(&chan->vchan, &xdev->common); |
| |
| xdev->chan[chan->id] = chan; |
| |
| return 0; |
| } |
| |
| static void xilinx_dpdma_chan_remove(struct xilinx_dpdma_chan *chan) |
| { |
| if (!chan) |
| return; |
| |
| tasklet_kill(&chan->err_task); |
| list_del(&chan->vchan.chan.device_node); |
| } |
| |
| static struct dma_chan *of_dma_xilinx_xlate(struct of_phandle_args *dma_spec, |
| struct of_dma *ofdma) |
| { |
| struct xilinx_dpdma_device *xdev = ofdma->of_dma_data; |
| u32 chan_id = dma_spec->args[0]; |
| |
| if (chan_id >= ARRAY_SIZE(xdev->chan)) |
| return NULL; |
| |
| if (!xdev->chan[chan_id]) |
| return NULL; |
| |
| return dma_get_slave_channel(&xdev->chan[chan_id]->vchan.chan); |
| } |
| |
| static void dpdma_hw_init(struct xilinx_dpdma_device *xdev) |
| { |
| unsigned int i; |
| void __iomem *reg; |
| |
| /* Disable all interrupts */ |
| xilinx_dpdma_disable_irq(xdev); |
| |
| /* Stop all channels */ |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) { |
| reg = xdev->reg + XILINX_DPDMA_CH_BASE |
| + XILINX_DPDMA_CH_OFFSET * i; |
| dpdma_clr(reg, XILINX_DPDMA_CH_CNTL, XILINX_DPDMA_CH_CNTL_ENABLE); |
| } |
| |
| /* Clear the interrupt status registers */ |
| dpdma_write(xdev->reg, XILINX_DPDMA_ISR, XILINX_DPDMA_INTR_ALL); |
| dpdma_write(xdev->reg, XILINX_DPDMA_EISR, XILINX_DPDMA_EINTR_ALL); |
| } |
| |
| static int xilinx_dpdma_probe(struct platform_device *pdev) |
| { |
| struct xilinx_dpdma_device *xdev; |
| struct dma_device *ddev; |
| unsigned int i; |
| int ret; |
| |
| xdev = devm_kzalloc(&pdev->dev, sizeof(*xdev), GFP_KERNEL); |
| if (!xdev) |
| return -ENOMEM; |
| |
| xdev->dev = &pdev->dev; |
| xdev->ext_addr = sizeof(dma_addr_t) > 4; |
| |
| INIT_LIST_HEAD(&xdev->common.channels); |
| |
| platform_set_drvdata(pdev, xdev); |
| |
| xdev->axi_clk = devm_clk_get(xdev->dev, "axi_clk"); |
| if (IS_ERR(xdev->axi_clk)) |
| return PTR_ERR(xdev->axi_clk); |
| |
| xdev->reg = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(xdev->reg)) |
| return PTR_ERR(xdev->reg); |
| |
| dpdma_hw_init(xdev); |
| |
| xdev->irq = platform_get_irq(pdev, 0); |
| if (xdev->irq < 0) |
| return xdev->irq; |
| |
| ret = request_irq(xdev->irq, xilinx_dpdma_irq_handler, IRQF_SHARED, |
| dev_name(xdev->dev), xdev); |
| if (ret) { |
| dev_err(xdev->dev, "failed to request IRQ\n"); |
| return ret; |
| } |
| |
| ddev = &xdev->common; |
| ddev->dev = &pdev->dev; |
| |
| dma_cap_set(DMA_SLAVE, ddev->cap_mask); |
| dma_cap_set(DMA_PRIVATE, ddev->cap_mask); |
| dma_cap_set(DMA_CYCLIC, ddev->cap_mask); |
| dma_cap_set(DMA_INTERLEAVE, ddev->cap_mask); |
| dma_cap_set(DMA_REPEAT, ddev->cap_mask); |
| dma_cap_set(DMA_LOAD_EOT, ddev->cap_mask); |
| ddev->copy_align = fls(XILINX_DPDMA_ALIGN_BYTES - 1); |
| |
| ddev->device_alloc_chan_resources = xilinx_dpdma_alloc_chan_resources; |
| ddev->device_free_chan_resources = xilinx_dpdma_free_chan_resources; |
| ddev->device_prep_dma_cyclic = xilinx_dpdma_prep_dma_cyclic; |
| ddev->device_prep_interleaved_dma = xilinx_dpdma_prep_interleaved_dma; |
| /* TODO: Can we achieve better granularity ? */ |
| ddev->device_tx_status = dma_cookie_status; |
| ddev->device_issue_pending = xilinx_dpdma_issue_pending; |
| ddev->device_config = xilinx_dpdma_config; |
| ddev->device_pause = xilinx_dpdma_pause; |
| ddev->device_resume = xilinx_dpdma_resume; |
| ddev->device_terminate_all = xilinx_dpdma_terminate_all; |
| ddev->device_synchronize = xilinx_dpdma_synchronize; |
| ddev->src_addr_widths = BIT(DMA_SLAVE_BUSWIDTH_UNDEFINED); |
| ddev->directions = BIT(DMA_MEM_TO_DEV); |
| ddev->residue_granularity = DMA_RESIDUE_GRANULARITY_DESCRIPTOR; |
| |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); ++i) { |
| ret = xilinx_dpdma_chan_init(xdev, i); |
| if (ret < 0) { |
| dev_err(xdev->dev, "failed to initialize channel %u\n", |
| i); |
| goto error; |
| } |
| } |
| |
| ret = clk_prepare_enable(xdev->axi_clk); |
| if (ret) { |
| dev_err(xdev->dev, "failed to enable the axi clock\n"); |
| goto error; |
| } |
| |
| ret = dma_async_device_register(ddev); |
| if (ret) { |
| dev_err(xdev->dev, "failed to register the dma device\n"); |
| goto error_dma_async; |
| } |
| |
| ret = of_dma_controller_register(xdev->dev->of_node, |
| of_dma_xilinx_xlate, ddev); |
| if (ret) { |
| dev_err(xdev->dev, "failed to register DMA to DT DMA helper\n"); |
| goto error_of_dma; |
| } |
| |
| xilinx_dpdma_enable_irq(xdev); |
| |
| xilinx_dpdma_debugfs_init(xdev); |
| |
| dev_info(&pdev->dev, "Xilinx DPDMA engine is probed\n"); |
| |
| return 0; |
| |
| error_of_dma: |
| dma_async_device_unregister(ddev); |
| error_dma_async: |
| clk_disable_unprepare(xdev->axi_clk); |
| error: |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) |
| xilinx_dpdma_chan_remove(xdev->chan[i]); |
| |
| free_irq(xdev->irq, xdev); |
| |
| return ret; |
| } |
| |
| static void xilinx_dpdma_remove(struct platform_device *pdev) |
| { |
| struct xilinx_dpdma_device *xdev = platform_get_drvdata(pdev); |
| unsigned int i; |
| |
| /* Start by disabling the IRQ to avoid races during cleanup. */ |
| free_irq(xdev->irq, xdev); |
| |
| xilinx_dpdma_disable_irq(xdev); |
| of_dma_controller_free(pdev->dev.of_node); |
| dma_async_device_unregister(&xdev->common); |
| clk_disable_unprepare(xdev->axi_clk); |
| |
| for (i = 0; i < ARRAY_SIZE(xdev->chan); i++) |
| xilinx_dpdma_chan_remove(xdev->chan[i]); |
| } |
| |
| static const struct of_device_id xilinx_dpdma_of_match[] = { |
| { .compatible = "xlnx,zynqmp-dpdma",}, |
| { /* end of table */ }, |
| }; |
| MODULE_DEVICE_TABLE(of, xilinx_dpdma_of_match); |
| |
| static struct platform_driver xilinx_dpdma_driver = { |
| .probe = xilinx_dpdma_probe, |
| .remove_new = xilinx_dpdma_remove, |
| .driver = { |
| .name = "xilinx-zynqmp-dpdma", |
| .of_match_table = xilinx_dpdma_of_match, |
| }, |
| }; |
| |
| module_platform_driver(xilinx_dpdma_driver); |
| |
| MODULE_AUTHOR("Xilinx, Inc."); |
| MODULE_DESCRIPTION("Xilinx ZynqMP DPDMA driver"); |
| MODULE_LICENSE("GPL v2"); |