blob: f824fdae0da20afc8976d0fa1f8063a5bd5894da [file] [log] [blame]
Atheros AR9331 built-in switch
=============================
It is a switch built-in to Atheros AR9331 WiSoC and addressable over internal
MDIO bus. All PHYs are built-in as well.
Required properties:
- compatible: should be: "qca,ar9331-switch"
- reg: Address on the MII bus for the switch.
- resets : Must contain an entry for each entry in reset-names.
- reset-names : Must include the following entries: "switch"
- interrupt-parent: Phandle to the parent interrupt controller
- interrupts: IRQ line for the switch
- interrupt-controller: Indicates the switch is itself an interrupt
controller. This is used for the PHY interrupts.
- #interrupt-cells: must be 1
- mdio: Container of PHY and devices on the switches MDIO bus.
See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
required and optional properties.
Examples:
eth0: ethernet@19000000 {
compatible = "qca,ar9330-eth";
reg = <0x19000000 0x200>;
interrupts = <4>;
resets = <&rst 9>, <&rst 22>;
reset-names = "mac", "mdio";
clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
clock-names = "eth", "mdio";
phy-mode = "mii";
phy-handle = <&phy_port4>;
};
eth1: ethernet@1a000000 {
compatible = "qca,ar9330-eth";
reg = <0x1a000000 0x200>;
interrupts = <5>;
resets = <&rst 13>, <&rst 23>;
reset-names = "mac", "mdio";
clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
clock-names = "eth", "mdio";
phy-mode = "gmii";
fixed-link {
speed = <1000>;
full-duplex;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch10: switch@10 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "qca,ar9331-switch";
reg = <0x10>;
resets = <&rst 8>;
reset-names = "switch";
interrupt-parent = <&miscintc>;
interrupts = <12>;
interrupt-controller;
#interrupt-cells = <1>;
ports {
#address-cells = <1>;
#size-cells = <0>;
switch_port0: port@0 {
reg = <0x0>;
ethernet = <&eth1>;
phy-mode = "gmii";
fixed-link {
speed = <1000>;
full-duplex;
};
};
switch_port1: port@1 {
reg = <0x1>;
phy-handle = <&phy_port0>;
phy-mode = "internal";
};
switch_port2: port@2 {
reg = <0x2>;
phy-handle = <&phy_port1>;
phy-mode = "internal";
};
switch_port3: port@3 {
reg = <0x3>;
phy-handle = <&phy_port2>;
phy-mode = "internal";
};
switch_port4: port@4 {
reg = <0x4>;
phy-handle = <&phy_port3>;
phy-mode = "internal";
};
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
interrupt-parent = <&switch10>;
phy_port0: phy@0 {
reg = <0x0>;
interrupts = <0>;
};
phy_port1: phy@1 {
reg = <0x1>;
interrupts = <0>;
};
phy_port2: phy@2 {
reg = <0x2>;
interrupts = <0>;
};
phy_port3: phy@3 {
reg = <0x3>;
interrupts = <0>;
};
phy_port4: phy@4 {
reg = <0x4>;
interrupts = <0>;
};
};
};
};
};