| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * IPQ6018 SoC device tree source |
| * |
| * Copyright (c) 2019, The Linux Foundation. All rights reserved. |
| */ |
| |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/clock/qcom,gcc-ipq6018.h> |
| #include <dt-bindings/reset/qcom,gcc-ipq6018.h> |
| #include <dt-bindings/clock/qcom,apss-ipq.h> |
| |
| / { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| interrupt-parent = <&intc>; |
| |
| clocks { |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| clock-frequency = <32000>; |
| #clock-cells = <0>; |
| }; |
| |
| xo: xo { |
| compatible = "fixed-clock"; |
| clock-frequency = <24000000>; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| cpus: cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| reg = <0x0>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; |
| clock-names = "cpu"; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-supply = <&ipq6018_s2>; |
| }; |
| |
| CPU1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| enable-method = "psci"; |
| reg = <0x1>; |
| next-level-cache = <&L2_0>; |
| clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; |
| clock-names = "cpu"; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-supply = <&ipq6018_s2>; |
| }; |
| |
| CPU2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| enable-method = "psci"; |
| reg = <0x2>; |
| next-level-cache = <&L2_0>; |
| clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; |
| clock-names = "cpu"; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-supply = <&ipq6018_s2>; |
| }; |
| |
| CPU3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "arm,cortex-a53"; |
| enable-method = "psci"; |
| reg = <0x3>; |
| next-level-cache = <&L2_0>; |
| clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>; |
| clock-names = "cpu"; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-supply = <&ipq6018_s2>; |
| }; |
| |
| L2_0: l2-cache { |
| compatible = "cache"; |
| cache-level = <0x2>; |
| }; |
| }; |
| |
| cpu_opp_table: opp-table-cpu { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| |
| opp-864000000 { |
| opp-hz = /bits/ 64 <864000000>; |
| opp-microvolt = <725000>; |
| clock-latency-ns = <200000>; |
| }; |
| opp-1056000000 { |
| opp-hz = /bits/ 64 <1056000000>; |
| opp-microvolt = <787500>; |
| clock-latency-ns = <200000>; |
| }; |
| opp-1320000000 { |
| opp-hz = /bits/ 64 <1320000000>; |
| opp-microvolt = <862500>; |
| clock-latency-ns = <200000>; |
| }; |
| opp-1440000000 { |
| opp-hz = /bits/ 64 <1440000000>; |
| opp-microvolt = <925000>; |
| clock-latency-ns = <200000>; |
| }; |
| opp-1608000000 { |
| opp-hz = /bits/ 64 <1608000000>; |
| opp-microvolt = <987500>; |
| clock-latency-ns = <200000>; |
| }; |
| opp-1800000000 { |
| opp-hz = /bits/ 64 <1800000000>; |
| opp-microvolt = <1062500>; |
| clock-latency-ns = <200000>; |
| }; |
| }; |
| |
| firmware { |
| scm { |
| compatible = "qcom,scm-ipq6018", "qcom,scm"; |
| }; |
| }; |
| |
| pmuv8: pmu { |
| compatible = "arm,cortex-a53-pmu"; |
| interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | |
| IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| psci: psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| rpm_msg_ram: memory@60000 { |
| reg = <0x0 0x60000 0x0 0x6000>; |
| no-map; |
| }; |
| |
| tz: memory@4a600000 { |
| reg = <0x0 0x4a600000 0x0 0x00400000>; |
| no-map; |
| }; |
| |
| smem_region: memory@4aa00000 { |
| reg = <0x0 0x4aa00000 0x0 0x00100000>; |
| no-map; |
| }; |
| |
| q6_region: memory@4ab00000 { |
| reg = <0x0 0x4ab00000 0x0 0x05500000>; |
| no-map; |
| }; |
| }; |
| |
| smem { |
| compatible = "qcom,smem"; |
| memory-region = <&smem_region>; |
| hwlocks = <&tcsr_mutex 0>; |
| }; |
| |
| soc: soc { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0 0 0 0 0x0 0xffffffff>; |
| dma-ranges; |
| compatible = "simple-bus"; |
| |
| prng: qrng@e1000 { |
| compatible = "qcom,prng-ee"; |
| reg = <0x0 0xe3000 0x0 0x1000>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| cryptobam: dma-controller@704000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x0 0x00704000 0x0 0x20000>; |
| interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_CRYPTO_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <1>; |
| qcom,controlled-remotely; |
| }; |
| |
| crypto: crypto@73a000 { |
| compatible = "qcom,crypto-v5.1"; |
| reg = <0x0 0x0073a000 0x0 0x6000>; |
| clocks = <&gcc GCC_CRYPTO_AHB_CLK>, |
| <&gcc GCC_CRYPTO_AXI_CLK>, |
| <&gcc GCC_CRYPTO_CLK>; |
| clock-names = "iface", "bus", "core"; |
| dmas = <&cryptobam 2>, <&cryptobam 3>; |
| dma-names = "rx", "tx"; |
| }; |
| |
| tlmm: pinctrl@1000000 { |
| compatible = "qcom,ipq6018-pinctrl"; |
| reg = <0x0 0x01000000 0x0 0x300000>; |
| interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&tlmm 0 0 80>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| serial_3_pins: serial3-state { |
| pins = "gpio44", "gpio45"; |
| function = "blsp2_uart"; |
| drive-strength = <8>; |
| bias-pull-down; |
| }; |
| |
| qpic_pins: qpic-state { |
| pins = "gpio1", "gpio3", "gpio4", |
| "gpio5", "gpio6", "gpio7", |
| "gpio8", "gpio10", "gpio11", |
| "gpio12", "gpio13", "gpio14", |
| "gpio15", "gpio17"; |
| function = "qpic_pad"; |
| drive-strength = <8>; |
| bias-disable; |
| }; |
| }; |
| |
| gcc: gcc@1800000 { |
| compatible = "qcom,gcc-ipq6018"; |
| reg = <0x0 0x01800000 0x0 0x80000>; |
| clocks = <&xo>, <&sleep_clk>; |
| clock-names = "xo", "sleep_clk"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| }; |
| |
| tcsr_mutex: hwlock@1905000 { |
| compatible = "qcom,ipq6018-tcsr-mutex", "qcom,tcsr-mutex"; |
| reg = <0x0 0x01905000 0x0 0x1000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tcsr: syscon@1937000 { |
| compatible = "qcom,tcsr-ipq6018", "syscon"; |
| reg = <0x0 0x01937000 0x0 0x21000>; |
| }; |
| |
| blsp_dma: dma-controller@7884000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x0 0x07884000 0x0 0x2b000>; |
| interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| }; |
| |
| blsp1_uart3: serial@78b1000 { |
| compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; |
| reg = <0x0 0x078b1000 0x0 0x200>; |
| interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| status = "disabled"; |
| }; |
| |
| blsp1_spi1: spi@78b5000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x078b5000 0x0 0x600>; |
| interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>; |
| spi-max-frequency = <50000000>; |
| clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp_dma 12>, <&blsp_dma 13>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp1_spi2: spi@78b6000 { |
| compatible = "qcom,spi-qup-v2.2.1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x078b6000 0x0 0x600>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| spi-max-frequency = <50000000>; |
| clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| dmas = <&blsp_dma 14>, <&blsp_dma 15>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp1_i2c2: i2c@78b6000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x078b6000 0x0 0x600>; |
| interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp_dma 14>, <&blsp_dma 15>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| blsp1_i2c3: i2c@78b7000 { |
| compatible = "qcom,i2c-qup-v2.2.1"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x0 0x078b7000 0x0 0x600>; |
| interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, |
| <&gcc GCC_BLSP1_AHB_CLK>; |
| clock-names = "core", "iface"; |
| clock-frequency = <400000>; |
| dmas = <&blsp_dma 16>, <&blsp_dma 17>; |
| dma-names = "tx", "rx"; |
| status = "disabled"; |
| }; |
| |
| qpic_bam: dma-controller@7984000 { |
| compatible = "qcom,bam-v1.7.0"; |
| reg = <0x0 0x07984000 0x0 0x1a000>; |
| interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&gcc GCC_QPIC_AHB_CLK>; |
| clock-names = "bam_clk"; |
| #dma-cells = <1>; |
| qcom,ee = <0>; |
| status = "disabled"; |
| }; |
| |
| qpic_nand: nand-controller@79b0000 { |
| compatible = "qcom,ipq6018-nand"; |
| reg = <0x0 0x079b0000 0x0 0x10000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&gcc GCC_QPIC_CLK>, |
| <&gcc GCC_QPIC_AHB_CLK>; |
| clock-names = "core", "aon"; |
| |
| dmas = <&qpic_bam 0>, |
| <&qpic_bam 1>, |
| <&qpic_bam 2>; |
| dma-names = "tx", "rx", "cmd"; |
| pinctrl-0 = <&qpic_pins>; |
| pinctrl-names = "default"; |
| status = "disabled"; |
| }; |
| |
| intc: interrupt-controller@b000000 { |
| compatible = "qcom,msm-qgic2"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <0x3>; |
| reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/ |
| <0x0 0x0b002000 0x0 0x1000>, /*GICC*/ |
| <0x0 0x0b001000 0x0 0x1000>, /*GICH*/ |
| <0x0 0x0b004000 0x0 0x1000>; /*GICV*/ |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| ranges = <0 0 0 0xb00a000 0 0xffd>; |
| |
| v2m@0 { |
| compatible = "arm,gic-v2m-frame"; |
| msi-controller; |
| reg = <0x0 0x0 0x0 0xffd>; |
| }; |
| }; |
| |
| pcie_phy: phy@84000 { |
| compatible = "qcom,ipq6018-qmp-pcie-phy"; |
| reg = <0x0 0x84000 0x0 0x1bc>; /* Serdes PLL */ |
| status = "disabled"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_PCIE0_AUX_CLK>, |
| <&gcc GCC_PCIE0_AHB_CLK>; |
| clock-names = "aux", "cfg_ahb"; |
| |
| resets = <&gcc GCC_PCIE0_PHY_BCR>, |
| <&gcc GCC_PCIE0PHY_PHY_BCR>; |
| reset-names = "phy", |
| "common"; |
| |
| pcie_phy0: phy@84200 { |
| reg = <0x0 0x84200 0x0 0x16c>, /* Serdes Tx */ |
| <0x0 0x84400 0x0 0x200>, /* Serdes Rx */ |
| <0x0 0x84800 0x0 0x1f0>, /* PCS: Lane0, COM, PCIE */ |
| <0x0 0x84c00 0x0 0xf4>; /* pcs_misc */ |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_PCIE0_PIPE_CLK>; |
| clock-names = "pipe0"; |
| clock-output-names = "gcc_pcie0_pipe_clk_src"; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| pcie0: pci@20000000 { |
| compatible = "qcom,pcie-ipq6018"; |
| reg = <0x0 0x20000000 0x0 0xf1d>, |
| <0x0 0x20000f20 0x0 0xa8>, |
| <0x0 0x20001000 0x0 0x1000>, |
| <0x0 0x80000 0x0 0x4000>, |
| <0x0 0x20100000 0x0 0x1000>; |
| reg-names = "dbi", "elbi", "atu", "parf", "config"; |
| |
| device_type = "pci"; |
| linux,pci-domain = <0>; |
| bus-range = <0x00 0xff>; |
| num-lanes = <1>; |
| max-link-speed = <3>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| phys = <&pcie_phy0>; |
| phy-names = "pciephy"; |
| |
| ranges = <0x81000000 0 0x20200000 0 0x20200000 |
| 0 0x10000>, /* downstream I/O */ |
| <0x82000000 0 0x20220000 0 0x20220000 |
| 0 0xfde0000>; /* non-prefetchable memory */ |
| |
| interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "msi"; |
| |
| #interrupt-cells = <1>; |
| interrupt-map-mask = <0 0 0 0x7>; |
| interrupt-map = <0 0 0 1 &intc 0 75 |
| IRQ_TYPE_LEVEL_HIGH>, /* int_a */ |
| <0 0 0 2 &intc 0 78 |
| IRQ_TYPE_LEVEL_HIGH>, /* int_b */ |
| <0 0 0 3 &intc 0 79 |
| IRQ_TYPE_LEVEL_HIGH>, /* int_c */ |
| <0 0 0 4 &intc 0 83 |
| IRQ_TYPE_LEVEL_HIGH>; /* int_d */ |
| |
| clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>, |
| <&gcc GCC_PCIE0_AXI_M_CLK>, |
| <&gcc GCC_PCIE0_AXI_S_CLK>, |
| <&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>, |
| <&gcc PCIE0_RCHNG_CLK>; |
| clock-names = "iface", |
| "axi_m", |
| "axi_s", |
| "axi_bridge", |
| "rchng"; |
| |
| resets = <&gcc GCC_PCIE0_PIPE_ARES>, |
| <&gcc GCC_PCIE0_SLEEP_ARES>, |
| <&gcc GCC_PCIE0_CORE_STICKY_ARES>, |
| <&gcc GCC_PCIE0_AXI_MASTER_ARES>, |
| <&gcc GCC_PCIE0_AXI_SLAVE_ARES>, |
| <&gcc GCC_PCIE0_AHB_ARES>, |
| <&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>, |
| <&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>; |
| reset-names = "pipe", |
| "sleep", |
| "sticky", |
| "axi_m", |
| "axi_s", |
| "ahb", |
| "axi_m_sticky", |
| "axi_s_sticky"; |
| |
| status = "disabled"; |
| }; |
| |
| watchdog@b017000 { |
| compatible = "qcom,kpss-wdt"; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; |
| reg = <0x0 0x0b017000 0x0 0x40>; |
| clocks = <&sleep_clk>; |
| timeout-sec = <10>; |
| }; |
| |
| apcs_glb: mailbox@b111000 { |
| compatible = "qcom,ipq6018-apcs-apps-global"; |
| reg = <0x0 0x0b111000 0x0 0x1000>; |
| #clock-cells = <1>; |
| clocks = <&a53pll>, <&xo>; |
| clock-names = "pll", "xo"; |
| #mbox-cells = <1>; |
| }; |
| |
| a53pll: clock@b116000 { |
| compatible = "qcom,ipq6018-a53pll"; |
| reg = <0x0 0x0b116000 0x0 0x40>; |
| #clock-cells = <0>; |
| clocks = <&xo>; |
| clock-names = "xo"; |
| }; |
| |
| timer@b120000 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0 0 0x10000000>; |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0 0x0b120000 0x0 0x1000>; |
| |
| frame@b120000 { |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b121000 0x1000>, |
| <0x0b122000 0x1000>; |
| }; |
| |
| frame@b123000 { |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b123000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b124000 { |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b124000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b125000 { |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b125000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b126000 { |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b126000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b127000 { |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b127000 0x1000>; |
| status = "disabled"; |
| }; |
| |
| frame@b128000 { |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0b128000 0x1000>; |
| status = "disabled"; |
| }; |
| }; |
| |
| q6v5_wcss: remoteproc@cd00000 { |
| compatible = "qcom,ipq6018-wcss-pil"; |
| reg = <0x0 0x0cd00000 0x0 0x4040>, |
| <0x0 0x004ab000 0x0 0x20>; |
| reg-names = "qdsp6", |
| "rmb"; |
| interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>, |
| <&wcss_smp2p_in 0 0>, |
| <&wcss_smp2p_in 1 0>, |
| <&wcss_smp2p_in 2 0>, |
| <&wcss_smp2p_in 3 0>; |
| interrupt-names = "wdog", |
| "fatal", |
| "ready", |
| "handover", |
| "stop-ack"; |
| |
| resets = <&gcc GCC_WCSSAON_RESET>, |
| <&gcc GCC_WCSS_BCR>, |
| <&gcc GCC_WCSS_Q6_BCR>; |
| |
| reset-names = "wcss_aon_reset", |
| "wcss_reset", |
| "wcss_q6_reset"; |
| |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "prng"; |
| |
| qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>; |
| |
| qcom,smem-states = <&wcss_smp2p_out 0>, |
| <&wcss_smp2p_out 1>; |
| qcom,smem-state-names = "shutdown", |
| "stop"; |
| |
| memory-region = <&q6_region>; |
| |
| glink-edge { |
| interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>; |
| label = "rtr"; |
| qcom,remote-pid = <1>; |
| mboxes = <&apcs_glb 8>; |
| |
| qrtr_requests { |
| qcom,glink-channels = "IPCRTR"; |
| }; |
| }; |
| }; |
| |
| mdio: mdio@90000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio"; |
| reg = <0x0 0x90000 0x0 0x64>; |
| clocks = <&gcc GCC_MDIO_AHB_CLK>; |
| clock-names = "gcc_mdio_ahb_clk"; |
| status = "disabled"; |
| }; |
| |
| qusb_phy_1: qusb@59000 { |
| compatible = "qcom,ipq6018-qusb2-phy"; |
| reg = <0x0 0x059000 0x0 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>, |
| <&xo>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2_1_PHY_BCR>; |
| status = "disabled"; |
| }; |
| |
| usb2: usb@70f8800 { |
| compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; |
| reg = <0x0 0x070F8800 0x0 0x400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| clocks = <&gcc GCC_USB1_MASTER_CLK>, |
| <&gcc GCC_USB1_SLEEP_CLK>, |
| <&gcc GCC_USB1_MOCK_UTMI_CLK>; |
| clock-names = "core", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>, |
| <&gcc GCC_USB1_MOCK_UTMI_CLK>; |
| assigned-clock-rates = <133330000>, |
| <24000000>; |
| resets = <&gcc GCC_USB1_BCR>; |
| status = "disabled"; |
| |
| dwc_1: usb@7000000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0x7000000 0x0 0xcd00>; |
| interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&qusb_phy_1>; |
| phy-names = "usb2-phy"; |
| tx-fifo-resize; |
| snps,is-utmi-l1-suspend; |
| snps,hird-threshold = /bits/ 8 <0x0>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_u3_susphy_quirk; |
| dr_mode = "host"; |
| }; |
| }; |
| |
| ssphy_0: ssphy@78000 { |
| compatible = "qcom,ipq6018-qmp-usb3-phy"; |
| reg = <0x0 0x78000 0x0 0x1C4>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_USB0_AUX_CLK>, |
| <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, <&xo>; |
| clock-names = "aux", "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_USB0_PHY_BCR>, |
| <&gcc GCC_USB3PHY_0_PHY_BCR>; |
| reset-names = "phy","common"; |
| status = "disabled"; |
| |
| usb0_ssphy: phy@78200 { |
| reg = <0x0 0x00078200 0x0 0x130>, /* Tx */ |
| <0x0 0x00078400 0x0 0x200>, /* Rx */ |
| <0x0 0x00078800 0x0 0x1F8>, /* PCS */ |
| <0x0 0x00078600 0x0 0x044>; /* PCS misc */ |
| #phy-cells = <0>; |
| #clock-cells = <0>; |
| clocks = <&gcc GCC_USB0_PIPE_CLK>; |
| clock-names = "pipe0"; |
| clock-output-names = "gcc_usb0_pipe_clk_src"; |
| }; |
| }; |
| |
| qusb_phy_0: qusb@79000 { |
| compatible = "qcom,ipq6018-qusb2-phy"; |
| reg = <0x0 0x079000 0x0 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>, |
| <&xo>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2_0_PHY_BCR>; |
| status = "disabled"; |
| }; |
| |
| usb3: usb@8af8800 { |
| compatible = "qcom,ipq6018-dwc3", "qcom,dwc3"; |
| reg = <0x0 0x8AF8800 0x0 0x400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, |
| <&gcc GCC_USB0_MASTER_CLK>, |
| <&gcc GCC_USB0_SLEEP_CLK>, |
| <&gcc GCC_USB0_MOCK_UTMI_CLK>; |
| clock-names = "cfg_noc", |
| "core", |
| "sleep", |
| "mock_utmi"; |
| |
| assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>, |
| <&gcc GCC_USB0_MASTER_CLK>, |
| <&gcc GCC_USB0_MOCK_UTMI_CLK>; |
| assigned-clock-rates = <133330000>, |
| <133330000>, |
| <20000000>; |
| |
| resets = <&gcc GCC_USB0_BCR>; |
| status = "disabled"; |
| |
| dwc_0: usb@8a00000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0x8A00000 0x0 0xcd00>; |
| interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&qusb_phy_0>, <&usb0_ssphy>; |
| phy-names = "usb2-phy", "usb3-phy"; |
| clocks = <&xo>; |
| clock-names = "ref"; |
| tx-fifo-resize; |
| snps,is-utmi-l1-suspend; |
| snps,hird-threshold = /bits/ 8 <0x0>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_u3_susphy_quirk; |
| dr_mode = "host"; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| wcss: wcss-smp2p { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| |
| interrupt-parent = <&intc>; |
| interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs_glb 9>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| wcss_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| wcss_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| rpm-glink { |
| compatible = "qcom,glink-rpm"; |
| interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| mboxes = <&apcs_glb 0>; |
| |
| rpm_requests: glink-channel { |
| compatible = "qcom,rpm-ipq6018"; |
| qcom,glink-channels = "rpm_requests"; |
| |
| regulators { |
| compatible = "qcom,rpm-mp5496-regulators"; |
| |
| ipq6018_s2: s2 { |
| regulator-min-microvolt = <725000>; |
| regulator-max-microvolt = <1062500>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| }; |
