| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Copyright (C) 2021 Stephan Gerhold |
| */ |
| |
| /dts-v1/; |
| |
| #include "msm8916-pm8916.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/sound/apq8016-lpass.h> |
| |
| /* |
| * Note: The original firmware from Huawei can only boot 32-bit kernels. |
| * To boot this device tree using arm64 it is necessary to flash 64-bit TZ/HYP |
| * firmware (e.g. taken from the DragonBoard 410c). |
| * See https://wiki.postmarketos.org/wiki/Huawei_Ascend_G7_(huawei-g7) |
| * for suggested installation instructions. |
| */ |
| |
| / { |
| model = "Huawei Ascend G7"; |
| compatible = "huawei,g7", "qcom,msm8916"; |
| chassis-type = "handset"; |
| |
| aliases { |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_default>; |
| |
| label = "GPIO Buttons"; |
| |
| button-volume-up { |
| label = "Volume Up"; |
| gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_leds_default>; |
| |
| led-0 { |
| gpios = <&msmgpio 8 GPIO_ACTIVE_HIGH>; |
| color = <LED_COLOR_ID_RED>; |
| default-state = "off"; |
| function = LED_FUNCTION_INDICATOR; |
| }; |
| |
| led-1 { |
| gpios = <&msmgpio 9 GPIO_ACTIVE_HIGH>; |
| color = <LED_COLOR_ID_GREEN>; |
| default-state = "off"; |
| function = LED_FUNCTION_INDICATOR; |
| }; |
| |
| led-2 { |
| gpios = <&msmgpio 10 GPIO_ACTIVE_HIGH>; |
| color = <LED_COLOR_ID_BLUE>; |
| default-state = "off"; |
| function = LED_FUNCTION_INDICATOR; |
| }; |
| }; |
| |
| usb_id: usb-id { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&msmgpio 117 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb_id_default>; |
| }; |
| }; |
| |
| &blsp_i2c2 { |
| status = "okay"; |
| |
| magnetometer@c { |
| compatible = "asahi-kasei,ak09911"; |
| reg = <0x0c>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vid-supply = <&pm8916_l6>; |
| |
| reset-gpios = <&msmgpio 36 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mag_reset_default>; |
| }; |
| |
| accelerometer@1e { |
| compatible = "kionix,kx023-1025"; |
| reg = <0x1e>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <115 IRQ_TYPE_EDGE_RISING>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&accel_irq_default>; |
| |
| mount-matrix = "-1", "0", "0", |
| "0", "1", "0", |
| "0", "0", "1"; |
| }; |
| |
| proximity@39 { |
| compatible = "avago,apds9930"; |
| reg = <0x39>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <113 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vddio-supply = <&pm8916_l6>; |
| |
| led-max-microamp = <100000>; |
| amstaos,proximity-diodes = <1>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&prox_irq_default>; |
| }; |
| |
| regulator@3e { |
| compatible = "ti,tps65132"; |
| reg = <0x3e>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <®_lcd_en_default>; |
| |
| reg_lcd_pos: outp { |
| regulator-name = "outp"; |
| regulator-min-microvolt = <5400000>; |
| regulator-max-microvolt = <5400000>; |
| enable-gpios = <&msmgpio 97 GPIO_ACTIVE_HIGH>; |
| regulator-active-discharge = <1>; |
| }; |
| |
| reg_lcd_neg: outn { |
| regulator-name = "outn"; |
| regulator-min-microvolt = <5400000>; |
| regulator-max-microvolt = <5400000>; |
| enable-gpios = <&msmgpio 32 GPIO_ACTIVE_HIGH>; |
| regulator-active-discharge = <1>; |
| }; |
| }; |
| }; |
| |
| &blsp_i2c5 { |
| status = "okay"; |
| |
| rmi4@70 { |
| compatible = "syna,rmi4-i2c"; |
| reg = <0x70>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <13 IRQ_TYPE_EDGE_FALLING>; |
| |
| vdd-supply = <&pm8916_l17>; |
| vio-supply = <&pm8916_l16>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_irq_default>; |
| |
| syna,startup-delay-ms = <100>; |
| |
| rmi4-f01@1 { |
| reg = <0x1>; |
| syna,nosleep-mode = <1>; /* Allow sleeping */ |
| }; |
| |
| rmi4-f11@11 { |
| reg = <0x11>; |
| syna,sensor-type = <1>; /* Touchscreen */ |
| }; |
| }; |
| }; |
| |
| &blsp_i2c6 { |
| status = "okay"; |
| |
| nfc@28 { |
| compatible = "nxp,pn547", "nxp,nxp-nci-i2c"; |
| reg = <0x28>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <21 IRQ_TYPE_EDGE_RISING>; |
| |
| enable-gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>; |
| firmware-gpios = <&msmgpio 2 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&nfc_default>; |
| }; |
| }; |
| |
| &blsp1_uart2 { |
| status = "okay"; |
| }; |
| |
| &lpass { |
| status = "okay"; |
| }; |
| |
| &pm8916_resin { |
| status = "okay"; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| |
| &pm8916_vib { |
| status = "okay"; |
| }; |
| |
| &pronto { |
| status = "okay"; |
| }; |
| |
| &sdhc_1 { |
| status = "okay"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; |
| }; |
| |
| &sdhc_2 { |
| status = "okay"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdhc2_cd_default>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdhc2_cd_default>; |
| |
| /* |
| * The Huawei device tree sets cd-gpios = <&msmgpio 38 GPIO_ACTIVE_HIGH>. |
| * However, gpio38 does not change its state when inserting/removing the |
| * SD card, it's just low all the time. The Huawei kernel seems to use |
| * polling for SD card detection instead. |
| * |
| * However, looking closer at the GPIO debug output it turns out that |
| * gpio56 switches its state when inserting/removing the SD card. |
| * It behaves just like gpio38 normally does. Usually GPIO56 is used as |
| * "UIM2_PRESENT", i.e. to check if a second SIM card is inserted. |
| * Maybe Huawei decided to replace the second SIM card slot with the |
| * SD card slot and forgot to re-route to gpio38. |
| */ |
| cd-gpios = <&msmgpio 56 GPIO_ACTIVE_LOW>; |
| }; |
| |
| &sound { |
| status = "okay"; |
| |
| model = "msm8916"; |
| audio-routing = |
| "AMIC1", "MIC BIAS External1", |
| "AMIC2", "MIC BIAS External2", |
| "AMIC3", "MIC BIAS External1"; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&cdc_pdm_lines_act>; |
| pinctrl-1 = <&cdc_pdm_lines_sus>; |
| |
| primary-dai-link { |
| link-name = "WCD"; |
| cpu { |
| sound-dai = <&lpass MI2S_PRIMARY>; |
| }; |
| codec { |
| sound-dai = <&lpass_codec 0>, <&wcd_codec 0>; |
| }; |
| }; |
| |
| tertiary-dai-link { |
| link-name = "WCD-Capture"; |
| cpu { |
| sound-dai = <&lpass MI2S_TERTIARY>; |
| }; |
| codec { |
| sound-dai = <&lpass_codec 1>, <&wcd_codec 1>; |
| }; |
| }; |
| }; |
| |
| &usb { |
| status = "okay"; |
| extcon = <&usb_id>, <&usb_id>; |
| }; |
| |
| &usb_hs_phy { |
| extcon = <&usb_id>; |
| }; |
| |
| &wcd_codec { |
| qcom,micbias-lvl = <2800>; |
| qcom,mbhc-vthreshold-low = <75 150 237 450 500>; |
| qcom,mbhc-vthreshold-high = <75 150 237 450 500>; |
| qcom,hphl-jack-type-normally-open; |
| }; |
| |
| &smd_rpm_regulators { |
| vdd_l1_l2_l3-supply = <&pm8916_s3>; |
| vdd_l4_l5_l6-supply = <&pm8916_s4>; |
| vdd_l7-supply = <&pm8916_s4>; |
| |
| s3 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2100000>; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l8 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l9 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l10 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| l11 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| regulator-system-load = <200000>; |
| }; |
| |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l13 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l16 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l18 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| }; |
| |
| &msmgpio { |
| accel_irq_default: accel-irq-default-state { |
| pins = "gpio115"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| gpio_keys_default: gpio-keys-default-state { |
| pins = "gpio107"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| gpio_leds_default: gpio-leds-default-state { |
| pins = "gpio8", "gpio9", "gpio10"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| nfc_default: nfc-default-state { |
| pins = "gpio2", "gpio20", "gpio21"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| mag_reset_default: mag-reset-default-state { |
| pins = "gpio36"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| prox_irq_default: prox-irq-default-state { |
| pins = "gpio113"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| reg_lcd_en_default: reg-lcd-en-default-state { |
| pins = "gpio32", "gpio97"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdhc2_cd_default: sdhc2-cd-default-state { |
| pins = "gpio56"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| ts_irq_default: ts-irq-default-state { |
| pins = "gpio13"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| usb_id_default: usb-id-default-state { |
| pins = "gpio117"; |
| function = "gpio"; |
| |
| drive-strength = <8>; |
| bias-pull-up; |
| }; |
| }; |
