| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright (C) 2008, 2010 Davide Rizzo <elpa.rizzo@gmail.com> |
| * |
| * The LM95241 is a sensor chip made by National Semiconductors. |
| * It reports up to three temperatures (its own plus up to two external ones). |
| * Complete datasheet can be obtained from National's website at: |
| * http://www.national.com/ds.cgi/LM/LM95241.pdf |
| */ |
| |
| #include <linux/bitops.h> |
| #include <linux/err.h> |
| #include <linux/i2c.h> |
| #include <linux/init.h> |
| #include <linux/jiffies.h> |
| #include <linux/hwmon.h> |
| #include <linux/module.h> |
| #include <linux/mutex.h> |
| #include <linux/slab.h> |
| |
| #define DEVNAME "lm95241" |
| |
| static const unsigned short normal_i2c[] = { |
| 0x19, 0x2a, 0x2b, I2C_CLIENT_END }; |
| |
| /* LM95241 registers */ |
| #define LM95241_REG_R_MAN_ID 0xFE |
| #define LM95241_REG_R_CHIP_ID 0xFF |
| #define LM95241_REG_R_STATUS 0x02 |
| #define LM95241_REG_RW_CONFIG 0x03 |
| #define LM95241_REG_RW_REM_FILTER 0x06 |
| #define LM95241_REG_RW_TRUTHERM 0x07 |
| #define LM95241_REG_W_ONE_SHOT 0x0F |
| #define LM95241_REG_R_LOCAL_TEMPH 0x10 |
| #define LM95241_REG_R_REMOTE1_TEMPH 0x11 |
| #define LM95241_REG_R_REMOTE2_TEMPH 0x12 |
| #define LM95241_REG_R_LOCAL_TEMPL 0x20 |
| #define LM95241_REG_R_REMOTE1_TEMPL 0x21 |
| #define LM95241_REG_R_REMOTE2_TEMPL 0x22 |
| #define LM95241_REG_RW_REMOTE_MODEL 0x30 |
| |
| /* LM95241 specific bitfields */ |
| #define CFG_STOP BIT(6) |
| #define CFG_CR0076 0x00 |
| #define CFG_CR0182 BIT(4) |
| #define CFG_CR1000 BIT(5) |
| #define CFG_CR2700 (BIT(4) | BIT(5)) |
| #define CFG_CRMASK (BIT(4) | BIT(5)) |
| #define R1MS_MASK BIT(0) |
| #define R2MS_MASK BIT(2) |
| #define R1DF_MASK BIT(1) |
| #define R2DF_MASK BIT(2) |
| #define R1FE_MASK BIT(0) |
| #define R2FE_MASK BIT(2) |
| #define R1DM BIT(0) |
| #define R2DM BIT(1) |
| #define TT1_SHIFT 0 |
| #define TT2_SHIFT 4 |
| #define TT_OFF 0 |
| #define TT_ON 1 |
| #define TT_MASK 7 |
| #define NATSEMI_MAN_ID 0x01 |
| #define LM95231_CHIP_ID 0xA1 |
| #define LM95241_CHIP_ID 0xA4 |
| |
| static const u8 lm95241_reg_address[] = { |
| LM95241_REG_R_LOCAL_TEMPH, |
| LM95241_REG_R_LOCAL_TEMPL, |
| LM95241_REG_R_REMOTE1_TEMPH, |
| LM95241_REG_R_REMOTE1_TEMPL, |
| LM95241_REG_R_REMOTE2_TEMPH, |
| LM95241_REG_R_REMOTE2_TEMPL |
| }; |
| |
| /* Client data (each client gets its own) */ |
| struct lm95241_data { |
| struct i2c_client *client; |
| struct mutex update_lock; |
| unsigned long last_updated; /* in jiffies */ |
| unsigned long interval; /* in milli-seconds */ |
| bool valid; /* false until following fields are valid */ |
| /* registers values */ |
| u8 temp[ARRAY_SIZE(lm95241_reg_address)]; |
| u8 status, config, model, trutherm; |
| }; |
| |
| /* Conversions */ |
| static int temp_from_reg_signed(u8 val_h, u8 val_l) |
| { |
| s16 val_hl = (val_h << 8) | val_l; |
| return val_hl * 1000 / 256; |
| } |
| |
| static int temp_from_reg_unsigned(u8 val_h, u8 val_l) |
| { |
| u16 val_hl = (val_h << 8) | val_l; |
| return val_hl * 1000 / 256; |
| } |
| |
| static struct lm95241_data *lm95241_update_device(struct device *dev) |
| { |
| struct lm95241_data *data = dev_get_drvdata(dev); |
| struct i2c_client *client = data->client; |
| |
| mutex_lock(&data->update_lock); |
| |
| if (time_after(jiffies, data->last_updated |
| + msecs_to_jiffies(data->interval)) || |
| !data->valid) { |
| int i; |
| |
| dev_dbg(dev, "Updating lm95241 data.\n"); |
| for (i = 0; i < ARRAY_SIZE(lm95241_reg_address); i++) |
| data->temp[i] |
| = i2c_smbus_read_byte_data(client, |
| lm95241_reg_address[i]); |
| |
| data->status = i2c_smbus_read_byte_data(client, |
| LM95241_REG_R_STATUS); |
| data->last_updated = jiffies; |
| data->valid = true; |
| } |
| |
| mutex_unlock(&data->update_lock); |
| |
| return data; |
| } |
| |
| static int lm95241_read_chip(struct device *dev, u32 attr, int channel, |
| long *val) |
| { |
| struct lm95241_data *data = dev_get_drvdata(dev); |
| |
| switch (attr) { |
| case hwmon_chip_update_interval: |
| *val = data->interval; |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int lm95241_read_temp(struct device *dev, u32 attr, int channel, |
| long *val) |
| { |
| struct lm95241_data *data = lm95241_update_device(dev); |
| |
| switch (attr) { |
| case hwmon_temp_input: |
| if (!channel || (data->config & BIT(channel - 1))) |
| *val = temp_from_reg_signed(data->temp[channel * 2], |
| data->temp[channel * 2 + 1]); |
| else |
| *val = temp_from_reg_unsigned(data->temp[channel * 2], |
| data->temp[channel * 2 + 1]); |
| return 0; |
| case hwmon_temp_min: |
| if (channel == 1) |
| *val = (data->config & R1DF_MASK) ? -128000 : 0; |
| else |
| *val = (data->config & R2DF_MASK) ? -128000 : 0; |
| return 0; |
| case hwmon_temp_max: |
| if (channel == 1) |
| *val = (data->config & R1DF_MASK) ? 127875 : 255875; |
| else |
| *val = (data->config & R2DF_MASK) ? 127875 : 255875; |
| return 0; |
| case hwmon_temp_type: |
| if (channel == 1) |
| *val = (data->model & R1MS_MASK) ? 1 : 2; |
| else |
| *val = (data->model & R2MS_MASK) ? 1 : 2; |
| return 0; |
| case hwmon_temp_fault: |
| if (channel == 1) |
| *val = !!(data->status & R1DM); |
| else |
| *val = !!(data->status & R2DM); |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int lm95241_read(struct device *dev, enum hwmon_sensor_types type, |
| u32 attr, int channel, long *val) |
| { |
| switch (type) { |
| case hwmon_chip: |
| return lm95241_read_chip(dev, attr, channel, val); |
| case hwmon_temp: |
| return lm95241_read_temp(dev, attr, channel, val); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int lm95241_write_chip(struct device *dev, u32 attr, int channel, |
| long val) |
| { |
| struct lm95241_data *data = dev_get_drvdata(dev); |
| int convrate; |
| u8 config; |
| int ret; |
| |
| mutex_lock(&data->update_lock); |
| |
| switch (attr) { |
| case hwmon_chip_update_interval: |
| config = data->config & ~CFG_CRMASK; |
| if (val < 130) { |
| convrate = 76; |
| config |= CFG_CR0076; |
| } else if (val < 590) { |
| convrate = 182; |
| config |= CFG_CR0182; |
| } else if (val < 1850) { |
| convrate = 1000; |
| config |= CFG_CR1000; |
| } else { |
| convrate = 2700; |
| config |= CFG_CR2700; |
| } |
| data->interval = convrate; |
| data->config = config; |
| ret = i2c_smbus_write_byte_data(data->client, |
| LM95241_REG_RW_CONFIG, config); |
| break; |
| default: |
| ret = -EOPNOTSUPP; |
| break; |
| } |
| mutex_unlock(&data->update_lock); |
| return ret; |
| } |
| |
| static int lm95241_write_temp(struct device *dev, u32 attr, int channel, |
| long val) |
| { |
| struct lm95241_data *data = dev_get_drvdata(dev); |
| struct i2c_client *client = data->client; |
| int ret; |
| |
| mutex_lock(&data->update_lock); |
| |
| switch (attr) { |
| case hwmon_temp_min: |
| if (channel == 1) { |
| if (val < 0) |
| data->config |= R1DF_MASK; |
| else |
| data->config &= ~R1DF_MASK; |
| } else { |
| if (val < 0) |
| data->config |= R2DF_MASK; |
| else |
| data->config &= ~R2DF_MASK; |
| } |
| data->valid = false; |
| ret = i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, |
| data->config); |
| break; |
| case hwmon_temp_max: |
| if (channel == 1) { |
| if (val <= 127875) |
| data->config |= R1DF_MASK; |
| else |
| data->config &= ~R1DF_MASK; |
| } else { |
| if (val <= 127875) |
| data->config |= R2DF_MASK; |
| else |
| data->config &= ~R2DF_MASK; |
| } |
| data->valid = false; |
| ret = i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, |
| data->config); |
| break; |
| case hwmon_temp_type: |
| if (val != 1 && val != 2) { |
| ret = -EINVAL; |
| break; |
| } |
| if (channel == 1) { |
| data->trutherm &= ~(TT_MASK << TT1_SHIFT); |
| if (val == 1) { |
| data->model |= R1MS_MASK; |
| data->trutherm |= (TT_ON << TT1_SHIFT); |
| } else { |
| data->model &= ~R1MS_MASK; |
| data->trutherm |= (TT_OFF << TT1_SHIFT); |
| } |
| } else { |
| data->trutherm &= ~(TT_MASK << TT2_SHIFT); |
| if (val == 1) { |
| data->model |= R2MS_MASK; |
| data->trutherm |= (TT_ON << TT2_SHIFT); |
| } else { |
| data->model &= ~R2MS_MASK; |
| data->trutherm |= (TT_OFF << TT2_SHIFT); |
| } |
| } |
| ret = i2c_smbus_write_byte_data(client, |
| LM95241_REG_RW_REMOTE_MODEL, |
| data->model); |
| if (ret < 0) |
| break; |
| ret = i2c_smbus_write_byte_data(client, LM95241_REG_RW_TRUTHERM, |
| data->trutherm); |
| break; |
| default: |
| ret = -EOPNOTSUPP; |
| break; |
| } |
| |
| mutex_unlock(&data->update_lock); |
| |
| return ret; |
| } |
| |
| static int lm95241_write(struct device *dev, enum hwmon_sensor_types type, |
| u32 attr, int channel, long val) |
| { |
| switch (type) { |
| case hwmon_chip: |
| return lm95241_write_chip(dev, attr, channel, val); |
| case hwmon_temp: |
| return lm95241_write_temp(dev, attr, channel, val); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static umode_t lm95241_is_visible(const void *data, |
| enum hwmon_sensor_types type, |
| u32 attr, int channel) |
| { |
| switch (type) { |
| case hwmon_chip: |
| switch (attr) { |
| case hwmon_chip_update_interval: |
| return 0644; |
| } |
| break; |
| case hwmon_temp: |
| switch (attr) { |
| case hwmon_temp_input: |
| return 0444; |
| case hwmon_temp_fault: |
| return 0444; |
| case hwmon_temp_min: |
| case hwmon_temp_max: |
| case hwmon_temp_type: |
| return 0644; |
| } |
| break; |
| default: |
| break; |
| } |
| return 0; |
| } |
| |
| /* Return 0 if detection is successful, -ENODEV otherwise */ |
| static int lm95241_detect(struct i2c_client *new_client, |
| struct i2c_board_info *info) |
| { |
| struct i2c_adapter *adapter = new_client->adapter; |
| const char *name; |
| int mfg_id, chip_id; |
| |
| if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA)) |
| return -ENODEV; |
| |
| mfg_id = i2c_smbus_read_byte_data(new_client, LM95241_REG_R_MAN_ID); |
| if (mfg_id != NATSEMI_MAN_ID) |
| return -ENODEV; |
| |
| chip_id = i2c_smbus_read_byte_data(new_client, LM95241_REG_R_CHIP_ID); |
| switch (chip_id) { |
| case LM95231_CHIP_ID: |
| name = "lm95231"; |
| break; |
| case LM95241_CHIP_ID: |
| name = "lm95241"; |
| break; |
| default: |
| return -ENODEV; |
| } |
| |
| /* Fill the i2c board info */ |
| strscpy(info->type, name, I2C_NAME_SIZE); |
| return 0; |
| } |
| |
| static void lm95241_init_client(struct i2c_client *client, |
| struct lm95241_data *data) |
| { |
| data->interval = 1000; |
| data->config = CFG_CR1000; |
| data->trutherm = (TT_OFF << TT1_SHIFT) | (TT_OFF << TT2_SHIFT); |
| |
| i2c_smbus_write_byte_data(client, LM95241_REG_RW_CONFIG, data->config); |
| i2c_smbus_write_byte_data(client, LM95241_REG_RW_REM_FILTER, |
| R1FE_MASK | R2FE_MASK); |
| i2c_smbus_write_byte_data(client, LM95241_REG_RW_TRUTHERM, |
| data->trutherm); |
| i2c_smbus_write_byte_data(client, LM95241_REG_RW_REMOTE_MODEL, |
| data->model); |
| } |
| |
| static const struct hwmon_channel_info *lm95241_info[] = { |
| HWMON_CHANNEL_INFO(chip, |
| HWMON_C_UPDATE_INTERVAL), |
| HWMON_CHANNEL_INFO(temp, |
| HWMON_T_INPUT, |
| HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MIN | |
| HWMON_T_TYPE | HWMON_T_FAULT, |
| HWMON_T_INPUT | HWMON_T_MAX | HWMON_T_MIN | |
| HWMON_T_TYPE | HWMON_T_FAULT), |
| NULL |
| }; |
| |
| static const struct hwmon_ops lm95241_hwmon_ops = { |
| .is_visible = lm95241_is_visible, |
| .read = lm95241_read, |
| .write = lm95241_write, |
| }; |
| |
| static const struct hwmon_chip_info lm95241_chip_info = { |
| .ops = &lm95241_hwmon_ops, |
| .info = lm95241_info, |
| }; |
| |
| static int lm95241_probe(struct i2c_client *client) |
| { |
| struct device *dev = &client->dev; |
| struct lm95241_data *data; |
| struct device *hwmon_dev; |
| |
| data = devm_kzalloc(dev, sizeof(struct lm95241_data), GFP_KERNEL); |
| if (!data) |
| return -ENOMEM; |
| |
| data->client = client; |
| mutex_init(&data->update_lock); |
| |
| /* Initialize the LM95241 chip */ |
| lm95241_init_client(client, data); |
| |
| hwmon_dev = devm_hwmon_device_register_with_info(dev, client->name, |
| data, |
| &lm95241_chip_info, |
| NULL); |
| return PTR_ERR_OR_ZERO(hwmon_dev); |
| } |
| |
| /* Driver data (common to all clients) */ |
| static const struct i2c_device_id lm95241_id[] = { |
| { "lm95231", 0 }, |
| { "lm95241", 0 }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(i2c, lm95241_id); |
| |
| static struct i2c_driver lm95241_driver = { |
| .class = I2C_CLASS_HWMON, |
| .driver = { |
| .name = DEVNAME, |
| }, |
| .probe_new = lm95241_probe, |
| .id_table = lm95241_id, |
| .detect = lm95241_detect, |
| .address_list = normal_i2c, |
| }; |
| |
| module_i2c_driver(lm95241_driver); |
| |
| MODULE_AUTHOR("Davide Rizzo <elpa.rizzo@gmail.com>"); |
| MODULE_DESCRIPTION("LM95231/LM95241 sensor driver"); |
| MODULE_LICENSE("GPL"); |