| /* |
| * Copyright (C) 2003 - 2006 NetXen, Inc. |
| * All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License |
| * as published by the Free Software Foundation; either version 2 |
| * of the License, or (at your option) any later version. |
| * |
| * This program is distributed in the hope that it will be useful, but |
| * WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| * |
| * You should have received a copy of the GNU General Public License |
| * along with this program; if not, write to the Free Software |
| * Foundation, Inc., 59 Temple Place - Suite 330, Boston, |
| * MA 02111-1307, USA. |
| * |
| * The full GNU General Public License is included in this distribution |
| * in the file called LICENSE. |
| * |
| * Contact Information: |
| * info@netxen.com |
| * NetXen, |
| * 3965 Freedom Circle, Fourth floor, |
| * Santa Clara, CA 95054 |
| * |
| * |
| * Source file for NIC routines to access the Phantom hardware |
| * |
| */ |
| |
| #include "netxen_nic.h" |
| #include "netxen_nic_hw.h" |
| #include "netxen_nic_phan_reg.h" |
| |
| /* PCI Windowing for DDR regions. */ |
| |
| #define ADDR_IN_RANGE(addr, low, high) \ |
| (((addr) <= (high)) && ((addr) >= (low))) |
| |
| #define NETXEN_FLASH_BASE (BOOTLD_START) |
| #define NETXEN_PHANTOM_MEM_BASE (NETXEN_FLASH_BASE) |
| #define NETXEN_MAX_MTU 8000 + NETXEN_ENET_HEADER_SIZE + NETXEN_ETH_FCS_SIZE |
| #define NETXEN_MIN_MTU 64 |
| #define NETXEN_ETH_FCS_SIZE 4 |
| #define NETXEN_ENET_HEADER_SIZE 14 |
| #define NETXEN_WINDOW_ONE 0x2000000 /*CRB Window: bit 25 of CRB address */ |
| #define NETXEN_FIRMWARE_LEN ((16 * 1024) / 4) |
| #define NETXEN_NIU_HDRSIZE (0x1 << 6) |
| #define NETXEN_NIU_TLRSIZE (0x1 << 5) |
| |
| #define lower32(x) ((u32)((x) & 0xffffffff)) |
| #define upper32(x) \ |
| ((u32)(((unsigned long long)(x) >> 32) & 0xffffffff)) |
| |
| #define NETXEN_NIC_ZERO_PAUSE_ADDR 0ULL |
| #define NETXEN_NIC_UNIT_PAUSE_ADDR 0x200ULL |
| #define NETXEN_NIC_EPG_PAUSE_ADDR1 0x2200010000c28001ULL |
| #define NETXEN_NIC_EPG_PAUSE_ADDR2 0x0100088866554433ULL |
| |
| #define NETXEN_NIC_WINDOW_MARGIN 0x100000 |
| |
| unsigned long netxen_nic_pci_set_window(struct netxen_adapter *adapter, |
| unsigned long long addr); |
| void netxen_free_hw_resources(struct netxen_adapter *adapter); |
| |
| int netxen_nic_set_mac(struct net_device *netdev, void *p) |
| { |
| struct netxen_port *port = netdev_priv(netdev); |
| struct netxen_adapter *adapter = port->adapter; |
| struct sockaddr *addr = p; |
| |
| if (netif_running(netdev)) |
| return -EBUSY; |
| |
| if (!is_valid_ether_addr(addr->sa_data)) |
| return -EADDRNOTAVAIL; |
| |
| DPRINTK(INFO, "valid ether addr\n"); |
| memcpy(netdev->dev_addr, addr->sa_data, netdev->addr_len); |
| |
| if (adapter->macaddr_set) |
| adapter->macaddr_set(port, addr->sa_data); |
| |
| return 0; |
| } |
| |
| /* |
| * netxen_nic_set_multi - Multicast |
| */ |
| void netxen_nic_set_multi(struct net_device *netdev) |
| { |
| struct netxen_port *port = netdev_priv(netdev); |
| struct netxen_adapter *adapter = port->adapter; |
| struct dev_mc_list *mc_ptr; |
| __u32 netxen_mac_addr_cntl_data = 0; |
| |
| mc_ptr = netdev->mc_list; |
| if (netdev->flags & IFF_PROMISC) { |
| if (adapter->set_promisc) |
| adapter->set_promisc(adapter, |
| port->portnum, |
| NETXEN_NIU_PROMISC_MODE); |
| } else { |
| if (adapter->unset_promisc && |
| adapter->ahw.boardcfg.board_type |
| != NETXEN_BRDTYPE_P2_SB31_10G_IMEZ) |
| adapter->unset_promisc(adapter, |
| port->portnum, |
| NETXEN_NIU_NON_PROMISC_MODE); |
| } |
| if (adapter->ahw.board_type == NETXEN_NIC_XGBE) { |
| netxen_nic_mcr_set_mode_select(netxen_mac_addr_cntl_data, 0x03); |
| netxen_nic_mcr_set_id_pool0(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_id_pool1(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_id_pool2(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_id_pool3(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_enable_xtnd0(netxen_mac_addr_cntl_data); |
| netxen_nic_mcr_set_enable_xtnd1(netxen_mac_addr_cntl_data); |
| netxen_nic_mcr_set_enable_xtnd2(netxen_mac_addr_cntl_data); |
| netxen_nic_mcr_set_enable_xtnd3(netxen_mac_addr_cntl_data); |
| } else { |
| netxen_nic_mcr_set_mode_select(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_id_pool0(netxen_mac_addr_cntl_data, 0x00); |
| netxen_nic_mcr_set_id_pool1(netxen_mac_addr_cntl_data, 0x01); |
| netxen_nic_mcr_set_id_pool2(netxen_mac_addr_cntl_data, 0x02); |
| netxen_nic_mcr_set_id_pool3(netxen_mac_addr_cntl_data, 0x03); |
| } |
| writel(netxen_mac_addr_cntl_data, |
| NETXEN_CRB_NORMALIZE(adapter, NETXEN_MAC_ADDR_CNTL_REG)); |
| if (adapter->ahw.board_type == NETXEN_NIC_XGBE) { |
| writel(netxen_mac_addr_cntl_data, |
| NETXEN_CRB_NORMALIZE(adapter, |
| NETXEN_MULTICAST_ADDR_HI_0)); |
| } else { |
| writel(netxen_mac_addr_cntl_data, |
| NETXEN_CRB_NORMALIZE(adapter, |
| NETXEN_MULTICAST_ADDR_HI_1)); |
| } |
| netxen_mac_addr_cntl_data = 0; |
| writel(netxen_mac_addr_cntl_data, |
| NETXEN_CRB_NORMALIZE(adapter, NETXEN_NIU_GB_DROP_WRONGADDR)); |
| } |
| |
| /* |
| * netxen_nic_change_mtu - Change the Maximum Transfer Unit |
| * @returns 0 on success, negative on failure |
| */ |
| int netxen_nic_change_mtu(struct net_device *netdev, int mtu) |
| { |
| struct netxen_port *port = netdev_priv(netdev); |
| struct netxen_adapter *adapter = port->adapter; |
| int eff_mtu = mtu + NETXEN_ENET_HEADER_SIZE + NETXEN_ETH_FCS_SIZE; |
| |
| if ((eff_mtu > NETXEN_MAX_MTU) || (eff_mtu < NETXEN_MIN_MTU)) { |
| printk(KERN_ERR "%s: %s %d is not supported.\n", |
| netxen_nic_driver_name, netdev->name, mtu); |
| return -EINVAL; |
| } |
| |
| if (adapter->set_mtu) |
| adapter->set_mtu(port, mtu); |
| netdev->mtu = mtu; |
| |
| return 0; |
| } |
| |
| /* |
| * check if the firmware has been downloaded and ready to run and |
| * setup the address for the descriptors in the adapter |
| */ |
| int netxen_nic_hw_resources(struct netxen_adapter *adapter) |
| { |
| struct netxen_hardware_context *hw = &adapter->ahw; |
| u32 state = 0; |
| void *addr; |
| int loops = 0, err = 0; |
| int ctx, ring; |
| u32 card_cmdring = 0; |
| struct netxen_recv_context *recv_ctx; |
| struct netxen_rcv_desc_ctx *rcv_desc; |
| |
| DPRINTK(INFO, "crb_base: %lx %x", NETXEN_PCI_CRBSPACE, |
| PCI_OFFSET_SECOND_RANGE(adapter, NETXEN_PCI_CRBSPACE)); |
| DPRINTK(INFO, "cam base: %lx %x", NETXEN_CRB_CAM, |
| pci_base_offset(adapter, NETXEN_CRB_CAM)); |
| DPRINTK(INFO, "cam RAM: %lx %x", NETXEN_CAM_RAM_BASE, |
| pci_base_offset(adapter, NETXEN_CAM_RAM_BASE)); |
| |
| /* Window 1 call */ |
| card_cmdring = readl(NETXEN_CRB_NORMALIZE(adapter, CRB_CMDPEG_CMDRING)); |
| |
| DPRINTK(INFO, "Command Peg sends 0x%x for cmdring base\n", |
| card_cmdring); |
| |
| for (ctx = 0; ctx < MAX_RCV_CTX; ++ctx) { |
| DPRINTK(INFO, "Command Peg ready..waiting for rcv peg\n"); |
| loops = 0; |
| state = 0; |
| /* Window 1 call */ |
| state = readl(NETXEN_CRB_NORMALIZE(adapter, |
| recv_crb_registers[ctx]. |
| crb_rcvpeg_state)); |
| while (state != PHAN_PEG_RCV_INITIALIZED && loops < 20) { |
| udelay(100); |
| /* Window 1 call */ |
| state = readl(NETXEN_CRB_NORMALIZE(adapter, |
| recv_crb_registers |
| [ctx]. |
| crb_rcvpeg_state)); |
| loops++; |
| } |
| if (loops >= 20) { |
| printk(KERN_ERR "Rcv Peg initialization not complete:" |
| "%x.\n", state); |
| err = -EIO; |
| return err; |
| } |
| } |
| DPRINTK(INFO, "Recieve Peg ready too. starting stuff\n"); |
| |
| addr = netxen_alloc(adapter->ahw.pdev, |
| sizeof(struct netxen_ring_ctx) + |
| sizeof(uint32_t), |
| (dma_addr_t *) & adapter->ctx_desc_phys_addr, |
| &adapter->ctx_desc_pdev); |
| |
| printk("ctx_desc_phys_addr: 0x%llx\n", |
| (u64) adapter->ctx_desc_phys_addr); |
| if (addr == NULL) { |
| DPRINTK(ERR, "bad return from pci_alloc_consistent\n"); |
| err = -ENOMEM; |
| return err; |
| } |
| memset(addr, 0, sizeof(struct netxen_ring_ctx)); |
| adapter->ctx_desc = (struct netxen_ring_ctx *)addr; |
| adapter->ctx_desc->cmd_consumer_offset = |
| cpu_to_le64(adapter->ctx_desc_phys_addr + |
| sizeof(struct netxen_ring_ctx)); |
| adapter->cmd_consumer = (uint32_t *) (((char *)addr) + |
| sizeof(struct netxen_ring_ctx)); |
| |
| addr = pci_alloc_consistent(adapter->ahw.pdev, |
| sizeof(struct cmd_desc_type0) * |
| adapter->max_tx_desc_count, |
| (dma_addr_t *) & hw->cmd_desc_phys_addr); |
| printk("cmd_desc_phys_addr: 0x%llx\n", (u64) hw->cmd_desc_phys_addr); |
| |
| if (addr == NULL) { |
| DPRINTK(ERR, "bad return from pci_alloc_consistent\n"); |
| netxen_free_hw_resources(adapter); |
| return -ENOMEM; |
| } |
| |
| adapter->ctx_desc->cmd_ring_addr = |
| cpu_to_le64(hw->cmd_desc_phys_addr); |
| adapter->ctx_desc->cmd_ring_size = |
| cpu_to_le32(adapter->max_tx_desc_count); |
| |
| hw->cmd_desc_head = (struct cmd_desc_type0 *)addr; |
| |
| for (ctx = 0; ctx < MAX_RCV_CTX; ++ctx) { |
| recv_ctx = &adapter->recv_ctx[ctx]; |
| |
| for (ring = 0; ring < NUM_RCV_DESC_RINGS; ring++) { |
| rcv_desc = &recv_ctx->rcv_desc[ring]; |
| addr = netxen_alloc(adapter->ahw.pdev, |
| RCV_DESC_RINGSIZE, |
| &rcv_desc->phys_addr, |
| &rcv_desc->phys_pdev); |
| if (addr == NULL) { |
| DPRINTK(ERR, "bad return from " |
| "pci_alloc_consistent\n"); |
| netxen_free_hw_resources(adapter); |
| err = -ENOMEM; |
| return err; |
| } |
| rcv_desc->desc_head = (struct rcv_desc *)addr; |
| adapter->ctx_desc->rcv_ctx[ring].rcv_ring_addr = |
| cpu_to_le64(rcv_desc->phys_addr); |
| adapter->ctx_desc->rcv_ctx[ring].rcv_ring_size = |
| cpu_to_le32(rcv_desc->max_rx_desc_count); |
| } |
| |
| addr = netxen_alloc(adapter->ahw.pdev, STATUS_DESC_RINGSIZE, |
| &recv_ctx->rcv_status_desc_phys_addr, |
| &recv_ctx->rcv_status_desc_pdev); |
| if (addr == NULL) { |
| DPRINTK(ERR, "bad return from" |
| " pci_alloc_consistent\n"); |
| netxen_free_hw_resources(adapter); |
| err = -ENOMEM; |
| return err; |
| } |
| recv_ctx->rcv_status_desc_head = (struct status_desc *)addr; |
| adapter->ctx_desc->sts_ring_addr = |
| cpu_to_le64(recv_ctx->rcv_status_desc_phys_addr); |
| adapter->ctx_desc->sts_ring_size = |
| cpu_to_le32(adapter->max_rx_desc_count); |
| |
| } |
| /* Window = 1 */ |
| |
| writel(lower32(adapter->ctx_desc_phys_addr), |
| NETXEN_CRB_NORMALIZE(adapter, CRB_CTX_ADDR_REG_LO)); |
| writel(upper32(adapter->ctx_desc_phys_addr), |
| NETXEN_CRB_NORMALIZE(adapter, CRB_CTX_ADDR_REG_HI)); |
| writel(NETXEN_CTX_SIGNATURE, |
| NETXEN_CRB_NORMALIZE(adapter, CRB_CTX_SIGNATURE_REG)); |
| return err; |
| } |
| |
| void netxen_free_hw_resources(struct netxen_adapter *adapter) |
| { |
| struct netxen_recv_context *recv_ctx; |
| struct netxen_rcv_desc_ctx *rcv_desc; |
| int ctx, ring; |
| |
| if (adapter->ctx_desc != NULL) { |
| pci_free_consistent(adapter->ctx_desc_pdev, |
| sizeof(struct netxen_ring_ctx) + |
| sizeof(uint32_t), |
| adapter->ctx_desc, |
| adapter->ctx_desc_phys_addr); |
| adapter->ctx_desc = NULL; |
| } |
| |
| if (adapter->ahw.cmd_desc_head != NULL) { |
| pci_free_consistent(adapter->ahw.cmd_desc_pdev, |
| sizeof(struct cmd_desc_type0) * |
| adapter->max_tx_desc_count, |
| adapter->ahw.cmd_desc_head, |
| adapter->ahw.cmd_desc_phys_addr); |
| adapter->ahw.cmd_desc_head = NULL; |
| } |
| /* Special handling: there are 2 ports on this board */ |
| if (adapter->ahw.boardcfg.board_type == NETXEN_BRDTYPE_P2_SB31_10G_IMEZ) { |
| adapter->ahw.max_ports = 2; |
| } |
| |
| for (ctx = 0; ctx < MAX_RCV_CTX; ++ctx) { |
| recv_ctx = &adapter->recv_ctx[ctx]; |
| for (ring = 0; ring < NUM_RCV_DESC_RINGS; ring++) { |
| rcv_desc = &recv_ctx->rcv_desc[ring]; |
| |
| if (rcv_desc->desc_head != NULL) { |
| pci_free_consistent(rcv_desc->phys_pdev, |
| RCV_DESC_RINGSIZE, |
| rcv_desc->desc_head, |
| rcv_desc->phys_addr); |
| rcv_desc->desc_head = NULL; |
| } |
| } |
| |
| if (recv_ctx->rcv_status_desc_head != NULL) { |
| pci_free_consistent(recv_ctx->rcv_status_desc_pdev, |
| STATUS_DESC_RINGSIZE, |
| recv_ctx->rcv_status_desc_head, |
| recv_ctx-> |
| rcv_status_desc_phys_addr); |
| recv_ctx->rcv_status_desc_head = NULL; |
| } |
| } |
| } |
| |
| void netxen_tso_check(struct netxen_adapter *adapter, |
| struct cmd_desc_type0 *desc, struct sk_buff *skb) |
| { |
| if (desc->mss) { |
| desc->total_hdr_length = sizeof(struct ethhdr) + |
| ((skb->nh.iph)->ihl * sizeof(u32)) + |
| ((skb->h.th)->doff * sizeof(u32)); |
| netxen_set_cmd_desc_opcode(desc, TX_TCP_LSO); |
| } else if (skb->ip_summed == CHECKSUM_PARTIAL) { |
| if (skb->nh.iph->protocol == IPPROTO_TCP) { |
| netxen_set_cmd_desc_opcode(desc, TX_TCP_PKT); |
| } else if (skb->nh.iph->protocol == IPPROTO_UDP) { |
| netxen_set_cmd_desc_opcode(desc, TX_UDP_PKT); |
| } else { |
| return; |
| } |
| } |
| adapter->stats.xmitcsummed++; |
| desc->tcp_hdr_offset = skb->h.raw - skb->data; |
| desc->ip_hdr_offset = skb->nh.raw - skb->data; |
| } |
| |
| int netxen_is_flash_supported(struct netxen_adapter *adapter) |
| { |
| const int locs[] = { 0, 0x4, 0x100, 0x4000, 0x4128 }; |
| int addr, val01, val02, i, j; |
| |
| /* if the flash size less than 4Mb, make huge war cry and die */ |
| for (j = 1; j < 4; j++) { |
| addr = j * NETXEN_NIC_WINDOW_MARGIN; |
| for (i = 0; i < (sizeof(locs) / sizeof(locs[0])); i++) { |
| if (netxen_rom_fast_read(adapter, locs[i], &val01) == 0 |
| && netxen_rom_fast_read(adapter, (addr + locs[i]), |
| &val02) == 0) { |
| if (val01 == val02) |
| return -1; |
| } else |
| return -1; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int netxen_get_flash_block(struct netxen_adapter *adapter, int base, |
| int size, u32 * buf) |
| { |
| int i, addr; |
| u32 *ptr32; |
| |
| addr = base; |
| ptr32 = buf; |
| for (i = 0; i < size / sizeof(u32); i++) { |
| if (netxen_rom_fast_read(adapter, addr, ptr32) == -1) |
| return -1; |
| *ptr32 = cpu_to_le32(*ptr32); |
| ptr32++; |
| addr += sizeof(u32); |
| } |
| if ((char *)buf + size > (char *)ptr32) { |
| u32 local; |
| |
| if (netxen_rom_fast_read(adapter, addr, &local) == -1) |
| return -1; |
| local = cpu_to_le32(local); |
| memcpy(ptr32, &local, (char *)buf + size - (char *)ptr32); |
| } |
| |
| return 0; |
| } |
| |
| int netxen_get_flash_mac_addr(struct netxen_adapter *adapter, u64 mac[]) |
| { |
| u32 *pmac = (u32 *) & mac[0]; |
| |
| if (netxen_get_flash_block(adapter, |
| USER_START + |
| offsetof(struct netxen_new_user_info, |
| mac_addr), |
| FLASH_NUM_PORTS * sizeof(u64), pmac) == -1) { |
| return -1; |
| } |
| if (*mac == ~0ULL) { |
| if (netxen_get_flash_block(adapter, |
| USER_START_OLD + |
| offsetof(struct netxen_user_old_info, |
| mac_addr), |
| FLASH_NUM_PORTS * sizeof(u64), |
| pmac) == -1) |
| return -1; |
| if (*mac == ~0ULL) |
| return -1; |
| } |
| return 0; |
| } |
| |
| /* |
| * Changes the CRB window to the specified window. |
| */ |
| void netxen_nic_pci_change_crbwindow(struct netxen_adapter *adapter, u32 wndw) |
| { |
| void __iomem *offset; |
| u32 tmp; |
| int count = 0; |
| |
| if (adapter->curr_window == wndw) |
| return; |
| |
| /* |
| * Move the CRB window. |
| * We need to write to the "direct access" region of PCI |
| * to avoid a race condition where the window register has |
| * not been successfully written across CRB before the target |
| * register address is received by PCI. The direct region bypasses |
| * the CRB bus. |
| */ |
| offset = |
| PCI_OFFSET_SECOND_RANGE(adapter, |
| NETXEN_PCIX_PH_REG(PCIX_CRB_WINDOW)); |
| |
| if (wndw & 0x1) |
| wndw = NETXEN_WINDOW_ONE; |
| |
| writel(wndw, offset); |
| |
| /* MUST make sure window is set before we forge on... */ |
| while ((tmp = readl(offset)) != wndw) { |
| printk(KERN_WARNING "%s: %s WARNING: CRB window value not " |
| "registered properly: 0x%08x.\n", |
| netxen_nic_driver_name, __FUNCTION__, tmp); |
| mdelay(1); |
| if (count >= 10) |
| break; |
| count++; |
| } |
| |
| adapter->curr_window = wndw; |
| } |
| |
| void netxen_load_firmware(struct netxen_adapter *adapter) |
| { |
| int i; |
| long data, size = 0; |
| long flashaddr = NETXEN_FLASH_BASE, memaddr = NETXEN_PHANTOM_MEM_BASE; |
| u64 off; |
| void __iomem *addr; |
| |
| size = NETXEN_FIRMWARE_LEN; |
| writel(1, NETXEN_CRB_NORMALIZE(adapter, NETXEN_ROMUSB_GLB_CAS_RST)); |
| |
| for (i = 0; i < size; i++) { |
| if (netxen_rom_fast_read(adapter, flashaddr, (int *)&data) != 0) { |
| DPRINTK(ERR, |
| "Error in netxen_rom_fast_read(). Will skip" |
| "loading flash image\n"); |
| return; |
| } |
| off = netxen_nic_pci_set_window(adapter, memaddr); |
| addr = pci_base_offset(adapter, off); |
| writel(data, addr); |
| flashaddr += 4; |
| memaddr += 4; |
| } |
| udelay(100); |
| /* make sure Casper is powered on */ |
| writel(0x3fff, |
| NETXEN_CRB_NORMALIZE(adapter, NETXEN_ROMUSB_GLB_CHIP_CLK_CTRL)); |
| writel(0, NETXEN_CRB_NORMALIZE(adapter, NETXEN_ROMUSB_GLB_CAS_RST)); |
| |
| udelay(100); |
| } |
| |
| int |
| netxen_nic_hw_write_wx(struct netxen_adapter *adapter, u64 off, void *data, |
| int len) |
| { |
| void __iomem *addr; |
| |
| if (ADDR_IN_WINDOW1(off)) { |
| addr = NETXEN_CRB_NORMALIZE(adapter, off); |
| } else { /* Window 0 */ |
| addr = pci_base_offset(adapter, off); |
| netxen_nic_pci_change_crbwindow(adapter, 0); |
| } |
| |
| DPRINTK(INFO, "writing to base %lx offset %llx addr %p" |
| " data %llx len %d\n", |
| pci_base(adapter, off), off, addr, |
| *(unsigned long long *)data, len); |
| if (!addr) { |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| return 1; |
| } |
| |
| switch (len) { |
| case 1: |
| writeb(*(u8 *) data, addr); |
| break; |
| case 2: |
| writew(*(u16 *) data, addr); |
| break; |
| case 4: |
| writel(*(u32 *) data, addr); |
| break; |
| case 8: |
| writeq(*(u64 *) data, addr); |
| break; |
| default: |
| DPRINTK(INFO, |
| "writing data %lx to offset %llx, num words=%d\n", |
| *(unsigned long *)data, off, (len >> 3)); |
| |
| netxen_nic_hw_block_write64((u64 __iomem *) data, addr, |
| (len >> 3)); |
| break; |
| } |
| if (!ADDR_IN_WINDOW1(off)) |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| |
| return 0; |
| } |
| |
| int |
| netxen_nic_hw_read_wx(struct netxen_adapter *adapter, u64 off, void *data, |
| int len) |
| { |
| void __iomem *addr; |
| |
| if (ADDR_IN_WINDOW1(off)) { /* Window 1 */ |
| addr = NETXEN_CRB_NORMALIZE(adapter, off); |
| } else { /* Window 0 */ |
| addr = pci_base_offset(adapter, off); |
| netxen_nic_pci_change_crbwindow(adapter, 0); |
| } |
| |
| DPRINTK(INFO, "reading from base %lx offset %llx addr %p\n", |
| pci_base(adapter, off), off, addr); |
| if (!addr) { |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| return 1; |
| } |
| switch (len) { |
| case 1: |
| *(u8 *) data = readb(addr); |
| break; |
| case 2: |
| *(u16 *) data = readw(addr); |
| break; |
| case 4: |
| *(u32 *) data = readl(addr); |
| break; |
| case 8: |
| *(u64 *) data = readq(addr); |
| break; |
| default: |
| netxen_nic_hw_block_read64((u64 __iomem *) data, addr, |
| (len >> 3)); |
| break; |
| } |
| DPRINTK(INFO, "read %lx\n", *(unsigned long *)data); |
| |
| if (!ADDR_IN_WINDOW1(off)) |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| |
| return 0; |
| } |
| |
| void netxen_nic_reg_write(struct netxen_adapter *adapter, u64 off, u32 val) |
| { /* Only for window 1 */ |
| void __iomem *addr; |
| |
| addr = NETXEN_CRB_NORMALIZE(adapter, off); |
| DPRINTK(INFO, "writing to base %lx offset %llx addr %p data %x\n", |
| pci_base(adapter, off), off, addr, val); |
| writel(val, addr); |
| |
| } |
| |
| int netxen_nic_reg_read(struct netxen_adapter *adapter, u64 off) |
| { /* Only for window 1 */ |
| void __iomem *addr; |
| int val; |
| |
| addr = NETXEN_CRB_NORMALIZE(adapter, off); |
| DPRINTK(INFO, "reading from base %lx offset %llx addr %p\n", |
| pci_base(adapter, off), off, addr); |
| val = readl(addr); |
| writel(val, addr); |
| |
| return val; |
| } |
| |
| /* Change the window to 0, write and change back to window 1. */ |
| void netxen_nic_write_w0(struct netxen_adapter *adapter, u32 index, u32 value) |
| { |
| void __iomem *addr; |
| |
| netxen_nic_pci_change_crbwindow(adapter, 0); |
| addr = pci_base_offset(adapter, index); |
| writel(value, addr); |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| } |
| |
| /* Change the window to 0, read and change back to window 1. */ |
| void netxen_nic_read_w0(struct netxen_adapter *adapter, u32 index, u32 * value) |
| { |
| void __iomem *addr; |
| |
| addr = pci_base_offset(adapter, index); |
| |
| netxen_nic_pci_change_crbwindow(adapter, 0); |
| *value = readl(addr); |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| } |
| |
| int netxen_pci_set_window_warning_count = 0; |
| |
| unsigned long |
| netxen_nic_pci_set_window(struct netxen_adapter *adapter, |
| unsigned long long addr) |
| { |
| static int ddr_mn_window = -1; |
| static int qdr_sn_window = -1; |
| int window; |
| |
| if (ADDR_IN_RANGE(addr, NETXEN_ADDR_DDR_NET, NETXEN_ADDR_DDR_NET_MAX)) { |
| /* DDR network side */ |
| addr -= NETXEN_ADDR_DDR_NET; |
| window = (addr >> 25) & 0x3ff; |
| if (ddr_mn_window != window) { |
| ddr_mn_window = window; |
| writel(window, PCI_OFFSET_SECOND_RANGE(adapter, |
| NETXEN_PCIX_PH_REG |
| (PCIX_MN_WINDOW))); |
| /* MUST make sure window is set before we forge on... */ |
| readl(PCI_OFFSET_SECOND_RANGE(adapter, |
| NETXEN_PCIX_PH_REG |
| (PCIX_MN_WINDOW))); |
| } |
| addr -= (window * NETXEN_WINDOW_ONE); |
| addr += NETXEN_PCI_DDR_NET; |
| } else if (ADDR_IN_RANGE(addr, NETXEN_ADDR_OCM0, NETXEN_ADDR_OCM0_MAX)) { |
| addr -= NETXEN_ADDR_OCM0; |
| addr += NETXEN_PCI_OCM0; |
| } else if (ADDR_IN_RANGE(addr, NETXEN_ADDR_OCM1, NETXEN_ADDR_OCM1_MAX)) { |
| addr -= NETXEN_ADDR_OCM1; |
| addr += NETXEN_PCI_OCM1; |
| } else |
| if (ADDR_IN_RANGE |
| (addr, NETXEN_ADDR_QDR_NET, NETXEN_ADDR_QDR_NET_MAX)) { |
| /* QDR network side */ |
| addr -= NETXEN_ADDR_QDR_NET; |
| window = (addr >> 22) & 0x3f; |
| if (qdr_sn_window != window) { |
| qdr_sn_window = window; |
| writel((window << 22), |
| PCI_OFFSET_SECOND_RANGE(adapter, |
| NETXEN_PCIX_PH_REG |
| (PCIX_SN_WINDOW))); |
| /* MUST make sure window is set before we forge on... */ |
| readl(PCI_OFFSET_SECOND_RANGE(adapter, |
| NETXEN_PCIX_PH_REG |
| (PCIX_SN_WINDOW))); |
| } |
| addr -= (window * 0x400000); |
| addr += NETXEN_PCI_QDR_NET; |
| } else { |
| /* |
| * peg gdb frequently accesses memory that doesn't exist, |
| * this limits the chit chat so debugging isn't slowed down. |
| */ |
| if ((netxen_pci_set_window_warning_count++ < 8) |
| || (netxen_pci_set_window_warning_count % 64 == 0)) |
| printk("%s: Warning:netxen_nic_pci_set_window()" |
| " Unknown address range!\n", |
| netxen_nic_driver_name); |
| |
| } |
| return addr; |
| } |
| |
| int netxen_nic_get_board_info(struct netxen_adapter *adapter) |
| { |
| int rv = 0; |
| int addr = BRDCFG_START; |
| struct netxen_board_info *boardinfo; |
| int index; |
| u32 *ptr32; |
| |
| boardinfo = &adapter->ahw.boardcfg; |
| ptr32 = (u32 *) boardinfo; |
| |
| for (index = 0; index < sizeof(struct netxen_board_info) / sizeof(u32); |
| index++) { |
| if (netxen_rom_fast_read(adapter, addr, ptr32) == -1) { |
| return -EIO; |
| } |
| ptr32++; |
| addr += sizeof(u32); |
| } |
| if (boardinfo->magic != NETXEN_BDINFO_MAGIC) { |
| printk("%s: ERROR reading %s board config." |
| " Read %x, expected %x\n", netxen_nic_driver_name, |
| netxen_nic_driver_name, |
| boardinfo->magic, NETXEN_BDINFO_MAGIC); |
| rv = -1; |
| } |
| if (boardinfo->header_version != NETXEN_BDINFO_VERSION) { |
| printk("%s: Unknown board config version." |
| " Read %x, expected %x\n", netxen_nic_driver_name, |
| boardinfo->header_version, NETXEN_BDINFO_VERSION); |
| rv = -1; |
| } |
| |
| DPRINTK(INFO, "Discovered board type:0x%x ", boardinfo->board_type); |
| switch ((netxen_brdtype_t) boardinfo->board_type) { |
| case NETXEN_BRDTYPE_P2_SB35_4G: |
| adapter->ahw.board_type = NETXEN_NIC_GBE; |
| break; |
| case NETXEN_BRDTYPE_P2_SB31_10G: |
| case NETXEN_BRDTYPE_P2_SB31_10G_IMEZ: |
| case NETXEN_BRDTYPE_P2_SB31_10G_HMEZ: |
| case NETXEN_BRDTYPE_P2_SB31_10G_CX4: |
| adapter->ahw.board_type = NETXEN_NIC_XGBE; |
| break; |
| case NETXEN_BRDTYPE_P1_BD: |
| case NETXEN_BRDTYPE_P1_SB: |
| case NETXEN_BRDTYPE_P1_SMAX: |
| case NETXEN_BRDTYPE_P1_SOCK: |
| adapter->ahw.board_type = NETXEN_NIC_GBE; |
| break; |
| default: |
| printk("%s: Unknown(%x)\n", netxen_nic_driver_name, |
| boardinfo->board_type); |
| break; |
| } |
| |
| return rv; |
| } |
| |
| /* NIU access sections */ |
| |
| int netxen_nic_set_mtu_gb(struct netxen_port *port, int new_mtu) |
| { |
| struct netxen_adapter *adapter = port->adapter; |
| netxen_nic_write_w0(adapter, |
| NETXEN_NIU_GB_MAX_FRAME_SIZE(port->portnum), |
| new_mtu); |
| return 0; |
| } |
| |
| int netxen_nic_set_mtu_xgb(struct netxen_port *port, int new_mtu) |
| { |
| struct netxen_adapter *adapter = port->adapter; |
| new_mtu += NETXEN_NIU_HDRSIZE + NETXEN_NIU_TLRSIZE; |
| netxen_nic_write_w0(adapter, NETXEN_NIU_XGE_MAX_FRAME_SIZE, new_mtu); |
| return 0; |
| } |
| |
| void netxen_nic_init_niu_gb(struct netxen_adapter *adapter) |
| { |
| int portno; |
| for (portno = 0; portno < NETXEN_NIU_MAX_GBE_PORTS; portno++) |
| netxen_niu_gbe_init_port(adapter, portno); |
| } |
| |
| void netxen_nic_stop_all_ports(struct netxen_adapter *adapter) |
| { |
| int port_nr; |
| struct netxen_port *port; |
| |
| for (port_nr = 0; port_nr < adapter->ahw.max_ports; port_nr++) { |
| port = adapter->port[port_nr]; |
| if (adapter->stop_port) |
| adapter->stop_port(adapter, port->portnum); |
| } |
| } |
| |
| void |
| netxen_crb_writelit_adapter(struct netxen_adapter *adapter, unsigned long off, |
| int data) |
| { |
| void __iomem *addr; |
| |
| if (ADDR_IN_WINDOW1(off)) { |
| writel(data, NETXEN_CRB_NORMALIZE(adapter, off)); |
| } else { |
| netxen_nic_pci_change_crbwindow(adapter, 0); |
| addr = pci_base_offset(adapter, off); |
| writel(data, addr); |
| netxen_nic_pci_change_crbwindow(adapter, 1); |
| } |
| } |
| |
| void netxen_nic_set_link_parameters(struct netxen_port *port) |
| { |
| struct netxen_adapter *adapter = port->adapter; |
| __u32 status; |
| __u32 autoneg; |
| __u32 mode; |
| |
| netxen_nic_read_w0(adapter, NETXEN_NIU_MODE, &mode); |
| if (netxen_get_niu_enable_ge(mode)) { /* Gb 10/100/1000 Mbps mode */ |
| if (adapter->phy_read |
| && adapter-> |
| phy_read(adapter, port->portnum, |
| NETXEN_NIU_GB_MII_MGMT_ADDR_PHY_STATUS, |
| &status) == 0) { |
| if (netxen_get_phy_link(status)) { |
| switch (netxen_get_phy_speed(status)) { |
| case 0: |
| port->link_speed = SPEED_10; |
| break; |
| case 1: |
| port->link_speed = SPEED_100; |
| break; |
| case 2: |
| port->link_speed = SPEED_1000; |
| break; |
| default: |
| port->link_speed = -1; |
| break; |
| } |
| switch (netxen_get_phy_duplex(status)) { |
| case 0: |
| port->link_duplex = DUPLEX_HALF; |
| break; |
| case 1: |
| port->link_duplex = DUPLEX_FULL; |
| break; |
| default: |
| port->link_duplex = -1; |
| break; |
| } |
| if (adapter->phy_read |
| && adapter-> |
| phy_read(adapter, port->portnum, |
| NETXEN_NIU_GB_MII_MGMT_ADDR_AUTONEG, |
| &autoneg) != 0) |
| port->link_autoneg = autoneg; |
| } else |
| goto link_down; |
| } else { |
| link_down: |
| port->link_speed = -1; |
| port->link_duplex = -1; |
| } |
| } |
| } |
| |
| void netxen_nic_flash_print(struct netxen_adapter *adapter) |
| { |
| int valid = 1; |
| u32 fw_major = 0; |
| u32 fw_minor = 0; |
| u32 fw_build = 0; |
| char brd_name[NETXEN_MAX_SHORT_NAME]; |
| struct netxen_new_user_info user_info; |
| int i, addr = USER_START; |
| u32 *ptr32; |
| |
| struct netxen_board_info *board_info = &(adapter->ahw.boardcfg); |
| if (board_info->magic != NETXEN_BDINFO_MAGIC) { |
| printk |
| ("NetXen Unknown board config, Read 0x%x expected as 0x%x\n", |
| board_info->magic, NETXEN_BDINFO_MAGIC); |
| valid = 0; |
| } |
| if (board_info->header_version != NETXEN_BDINFO_VERSION) { |
| printk("NetXen Unknown board config version." |
| " Read %x, expected %x\n", |
| board_info->header_version, NETXEN_BDINFO_VERSION); |
| valid = 0; |
| } |
| if (valid) { |
| ptr32 = (u32 *) & user_info; |
| for (i = 0; |
| i < sizeof(struct netxen_new_user_info) / sizeof(u32); |
| i++) { |
| if (netxen_rom_fast_read(adapter, addr, ptr32) == -1) { |
| printk("%s: ERROR reading %s board userarea.\n", |
| netxen_nic_driver_name, |
| netxen_nic_driver_name); |
| return; |
| } |
| ptr32++; |
| addr += sizeof(u32); |
| } |
| get_brd_name_by_type(board_info->board_type, brd_name); |
| |
| printk("NetXen %s Board S/N %s Chip id 0x%x\n", |
| brd_name, user_info.serial_num, board_info->chip_id); |
| |
| printk("NetXen %s Board #%d, Chip id 0x%x\n", |
| board_info->board_type == 0x0b ? "XGB" : "GBE", |
| board_info->board_num, board_info->chip_id); |
| fw_major = readl(NETXEN_CRB_NORMALIZE(adapter, |
| NETXEN_FW_VERSION_MAJOR)); |
| fw_minor = readl(NETXEN_CRB_NORMALIZE(adapter, |
| NETXEN_FW_VERSION_MINOR)); |
| fw_build = |
| readl(NETXEN_CRB_NORMALIZE(adapter, NETXEN_FW_VERSION_SUB)); |
| |
| printk("NetXen Firmware version %d.%d.%d\n", fw_major, fw_minor, |
| fw_build); |
| } |
| if (fw_major != _NETXEN_NIC_LINUX_MAJOR) { |
| printk(KERN_ERR "The mismatch in driver version and firmware " |
| "version major number\n" |
| "Driver version major number = %d \t" |
| "Firmware version major number = %d \n", |
| _NETXEN_NIC_LINUX_MAJOR, fw_major); |
| adapter->driver_mismatch = 1; |
| } |
| if (fw_minor != _NETXEN_NIC_LINUX_MINOR && |
| fw_minor != (_NETXEN_NIC_LINUX_MINOR + 1)) { |
| printk(KERN_ERR "The mismatch in driver version and firmware " |
| "version minor number\n" |
| "Driver version minor number = %d \t" |
| "Firmware version minor number = %d \n", |
| _NETXEN_NIC_LINUX_MINOR, fw_minor); |
| adapter->driver_mismatch = 1; |
| } |
| if (adapter->driver_mismatch) |
| printk(KERN_INFO "Use the driver with version no %d.%d.xxx\n", |
| fw_major, fw_minor); |
| } |
| |