| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Device Tree File for the Kontron pitx-imx8m board. |
| * |
| * Copyright (C) 2021 Heiko Thiery <heiko.thiery@gmail.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include "imx8mq.dtsi" |
| #include <dt-bindings/net/ti-dp83867.h> |
| |
| / { |
| model = "Kontron pITX-imx8m"; |
| compatible = "kontron,pitx-imx8m", "fsl,imx8mq"; |
| |
| aliases { |
| i2c0 = &i2c1; |
| i2c1 = &i2c2; |
| i2c2 = &i2c3; |
| mmc0 = &usdhc1; |
| mmc1 = &usdhc2; |
| serial0 = &uart1; |
| serial1 = &uart2; |
| serial2 = &uart3; |
| spi0 = &qspi0; |
| spi1 = &ecspi2; |
| }; |
| |
| chosen { |
| stdout-path = "serial2:115200n8"; |
| }; |
| |
| pcie0_refclk: pcie0-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <100000000>; |
| }; |
| |
| pcie1_refclk: pcie1-clock { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <100000000>; |
| }; |
| |
| reg_usdhc2_vmmc: regulator-usdhc2-vmmc { |
| compatible = "regulator-fixed"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_reg_usdhc2>; |
| regulator-name = "V_3V3_SD"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; |
| off-on-delay-us = <20000>; |
| enable-active-high; |
| }; |
| }; |
| |
| &ecspi2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs>; |
| cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; |
| status = "okay"; |
| |
| tpm@0 { |
| compatible = "infineon,slb9670"; |
| reg = <0>; |
| spi-max-frequency = <43000000>; |
| }; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>; |
| ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_75_NS>; |
| ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; |
| reset-gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; |
| reset-assert-us = <10>; |
| reset-deassert-us = <280>; |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| pmic@8 { |
| compatible = "fsl,pfuze100"; |
| fsl,pfuze-support-disable-sw; |
| reg = <0x8>; |
| |
| regulators { |
| sw1a_reg: sw1ab { |
| regulator-name = "V_0V9_GPU"; |
| regulator-min-microvolt = <825000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| sw1c_reg: sw1c { |
| regulator-name = "V_0V9_VPU"; |
| regulator-min-microvolt = <825000>; |
| regulator-max-microvolt = <1100000>; |
| }; |
| |
| sw2_reg: sw2 { |
| regulator-name = "V_1V1_NVCC_DRAM"; |
| regulator-min-microvolt = <1100000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| }; |
| |
| sw3a_reg: sw3ab { |
| regulator-name = "V_1V0_DRAM"; |
| regulator-min-microvolt = <825000>; |
| regulator-max-microvolt = <1100000>; |
| regulator-always-on; |
| }; |
| |
| sw4_reg: sw4 { |
| regulator-name = "V_1V8_S0"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| }; |
| |
| swbst_reg: swbst { |
| regulator-name = "NC"; |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5150000>; |
| }; |
| |
| snvs_reg: vsnvs { |
| regulator-name = "V_0V9_SNVS"; |
| regulator-min-microvolt = <1000000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-always-on; |
| }; |
| |
| vref_reg: vrefddr { |
| regulator-name = "V_0V55_VREF_DDR"; |
| regulator-always-on; |
| }; |
| |
| vgen1_reg: vgen1 { |
| regulator-name = "V_1V5_CSI"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1550000>; |
| }; |
| |
| vgen2_reg: vgen2 { |
| regulator-name = "V_0V9_PHY"; |
| regulator-min-microvolt = <850000>; |
| regulator-max-microvolt = <975000>; |
| regulator-always-on; |
| }; |
| |
| vgen3_reg: vgen3 { |
| regulator-name = "V_1V8_PHY"; |
| regulator-min-microvolt = <1675000>; |
| regulator-max-microvolt = <1975000>; |
| regulator-always-on; |
| }; |
| |
| vgen4_reg: vgen4 { |
| regulator-name = "V_1V8_VDDA"; |
| regulator-min-microvolt = <1625000>; |
| regulator-max-microvolt = <1875000>; |
| regulator-always-on; |
| }; |
| |
| vgen5_reg: vgen5 { |
| regulator-name = "V_3V3_PHY"; |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3625000>; |
| regulator-always-on; |
| }; |
| |
| vgen6_reg: vgen6 { |
| regulator-name = "V_2V8_CAM"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| |
| fan-controller@1b { |
| compatible = "maxim,max6650"; |
| reg = <0x1b>; |
| maxim,fan-microvolt = <5000000>; |
| }; |
| |
| rtc@32 { |
| compatible = "microcrystal,rv8803"; |
| reg = <0x32>; |
| }; |
| |
| sensor@4b { |
| compatible = "national,lm75b"; |
| reg = <0x4b>; |
| }; |
| |
| eeprom@51 { |
| compatible = "atmel,24c32"; |
| reg = <0x51>; |
| pagesize = <32>; |
| }; |
| }; |
| |
| &i2c2 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c2>; |
| status = "okay"; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <100000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| }; |
| |
| /* M.2 B-key slot */ |
| &pcie0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pcie0>; |
| reset-gpio = <&gpio1 9 GPIO_ACTIVE_LOW>; |
| clocks = <&clk IMX8MQ_CLK_PCIE1_ROOT>, |
| <&pcie0_refclk>, |
| <&clk IMX8MQ_CLK_PCIE1_PHY>, |
| <&clk IMX8MQ_CLK_PCIE1_AUX>; |
| status = "okay"; |
| }; |
| |
| /* Intel Ethernet Controller I210/I211 */ |
| &pcie1 { |
| clocks = <&clk IMX8MQ_CLK_PCIE2_ROOT>, |
| <&pcie1_refclk>, |
| <&clk IMX8MQ_CLK_PCIE2_PHY>, |
| <&clk IMX8MQ_CLK_PCIE2_AUX>; |
| fsl,max-link-speed = <1>; |
| status = "okay"; |
| }; |
| |
| &pgc_gpu { |
| power-supply = <&sw1a_reg>; |
| }; |
| |
| &pgc_vpu { |
| power-supply = <&sw1c_reg>; |
| }; |
| |
| &qspi0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_qspi>; |
| status = "okay"; |
| |
| flash@0 { |
| compatible = "jedec,spi-nor"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <4>; |
| m25p,fast-read; |
| spi-max-frequency = <50000000>; |
| }; |
| }; |
| |
| &snvs_pwrkey { |
| status = "okay"; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| assigned-clocks = <&clk IMX8MQ_CLK_UART1>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; |
| status = "okay"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart2>; |
| assigned-clocks = <&clk IMX8MQ_CLK_UART2>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; |
| status = "okay"; |
| }; |
| |
| &uart3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart3>; |
| uart-has-rtscts; |
| assigned-clocks = <&clk IMX8MQ_CLK_UART3>; |
| assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_80M>; |
| status = "okay"; |
| }; |
| |
| &usb3_phy0 { |
| status = "okay"; |
| }; |
| |
| &usb3_phy1 { |
| status = "okay"; |
| }; |
| |
| &usb_dwc3_0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usb0>; |
| dr_mode = "otg"; |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| maximum-speed = "high-speed"; |
| status = "okay"; |
| }; |
| |
| &usb_dwc3_1 { |
| dr_mode = "host"; |
| status = "okay"; |
| }; |
| |
| &usdhc1 { |
| assigned-clocks = <&clk IMX8MQ_CLK_USDHC1>; |
| assigned-clock-rates = <400000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| vqmmc-supply = <&sw4_reg>; |
| bus-width = <8>; |
| non-removable; |
| no-sd; |
| no-sdio; |
| status = "okay"; |
| }; |
| |
| &usdhc2 { |
| assigned-clocks = <&clk IMX8MQ_CLK_USDHC2>; |
| assigned-clock-rates = <200000000>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; |
| pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; |
| bus-width = <4>; |
| cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; |
| wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; |
| vmmc-supply = <®_usdhc2_vmmc>; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_hog>; |
| |
| pinctrl_hog: hoggrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_NAND_CE1_B_GPIO3_IO2 0x19 /* TPM Reset */ |
| MX8MQ_IOMUXC_NAND_CE3_B_GPIO3_IO4 0x19 /* USB2 Hub Reset */ |
| >; |
| }; |
| |
| pinctrl_gpio: gpiogrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_NAND_CLE_GPIO3_IO5 0x19 /* GPIO0 */ |
| MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19 /* GPIO1 */ |
| MX8MQ_IOMUXC_NAND_WE_B_GPIO3_IO17 0x19 /* GPIO2 */ |
| MX8MQ_IOMUXC_NAND_WP_B_GPIO3_IO18 0x19 /* GPIO3 */ |
| MX8MQ_IOMUXC_NAND_READY_B_GPIO3_IO16 0x19 /* GPIO4 */ |
| MX8MQ_IOMUXC_NAND_DATA04_GPIO3_IO10 0x19 /* GPIO5 */ |
| MX8MQ_IOMUXC_NAND_DATA05_GPIO3_IO11 0x19 /* GPIO6 */ |
| MX8MQ_IOMUXC_NAND_DATA06_GPIO3_IO12 0x19 /* GPIO7 */ |
| >; |
| }; |
| |
| pinctrl_pcie0: pcie0grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_GPIO1_IO09_GPIO1_IO9 0x16 /* PCIE_PERST */ |
| MX8MQ_IOMUXC_UART4_TXD_GPIO5_IO29 0x16 /* W_DISABLE */ |
| >; |
| }; |
| |
| pinctrl_reg_usdhc2: regusdhc2gpiogrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD2_RESET_B_GPIO2_IO19 0x41 |
| >; |
| }; |
| |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_ENET_MDC_ENET1_MDC 0x3 |
| MX8MQ_IOMUXC_ENET_MDIO_ENET1_MDIO 0x23 |
| MX8MQ_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f |
| MX8MQ_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f |
| MX8MQ_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f |
| MX8MQ_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f |
| MX8MQ_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 |
| MX8MQ_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 |
| MX8MQ_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 |
| MX8MQ_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 |
| MX8MQ_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f |
| MX8MQ_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 |
| MX8MQ_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 |
| MX8MQ_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f |
| MX8MQ_IOMUXC_GPIO1_IO11_GPIO1_IO11 0x16 |
| MX8MQ_IOMUXC_GPIO1_IO15_GPIO1_IO15 0x16 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_I2C1_SCL_I2C1_SCL 0x4000007f |
| MX8MQ_IOMUXC_I2C1_SDA_I2C1_SDA 0x4000007f |
| >; |
| }; |
| |
| pinctrl_i2c2: i2c2grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_I2C2_SCL_I2C2_SCL 0x4000007f |
| MX8MQ_IOMUXC_I2C2_SDA_I2C2_SDA 0x4000007f |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_I2C3_SCL_I2C3_SCL 0x4000007f |
| MX8MQ_IOMUXC_I2C3_SDA_I2C3_SDA 0x4000007f |
| >; |
| }; |
| |
| pinctrl_qspi: qspigrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x82 |
| MX8MQ_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 |
| MX8MQ_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 |
| MX8MQ_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 |
| MX8MQ_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 |
| MX8MQ_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 |
| >; |
| }; |
| |
| pinctrl_ecspi2: ecspi2grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_ECSPI2_MOSI_ECSPI2_MOSI 0x19 |
| MX8MQ_IOMUXC_ECSPI2_MISO_ECSPI2_MISO 0x19 |
| MX8MQ_IOMUXC_ECSPI2_SCLK_ECSPI2_SCLK 0x19 |
| >; |
| }; |
| |
| pinctrl_ecspi2_cs: ecspi2csgrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_ECSPI2_SS0_GPIO5_IO13 0x19 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_UART1_TXD_UART1_DCE_TX 0x49 |
| MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX 0x49 |
| >; |
| }; |
| |
| pinctrl_uart2: uart2grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_UART2_TXD_UART2_DCE_TX 0x49 |
| MX8MQ_IOMUXC_UART2_RXD_UART2_DCE_RX 0x49 |
| >; |
| }; |
| |
| pinctrl_uart3: uart3grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_UART3_TXD_UART3_DCE_TX 0x49 |
| MX8MQ_IOMUXC_UART3_RXD_UART3_DCE_RX 0x49 |
| MX8MQ_IOMUXC_ECSPI1_SS0_UART3_DCE_RTS_B 0x49 |
| MX8MQ_IOMUXC_ECSPI1_MISO_UART3_DCE_CTS_B 0x49 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x83 |
| MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xc3 |
| MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xc3 |
| MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x83 |
| MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1-100grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x8d |
| MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xcd |
| MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xcd |
| MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xcd |
| MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xcd |
| MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xcd |
| MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xcd |
| MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xcd |
| MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xcd |
| MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xcd |
| MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x8d |
| MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1-200grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD1_CLK_USDHC1_CLK 0x9f |
| MX8MQ_IOMUXC_SD1_CMD_USDHC1_CMD 0xdf |
| MX8MQ_IOMUXC_SD1_DATA0_USDHC1_DATA0 0xdf |
| MX8MQ_IOMUXC_SD1_DATA1_USDHC1_DATA1 0xdf |
| MX8MQ_IOMUXC_SD1_DATA2_USDHC1_DATA2 0xdf |
| MX8MQ_IOMUXC_SD1_DATA3_USDHC1_DATA3 0xdf |
| MX8MQ_IOMUXC_SD1_DATA4_USDHC1_DATA4 0xdf |
| MX8MQ_IOMUXC_SD1_DATA5_USDHC1_DATA5 0xdf |
| MX8MQ_IOMUXC_SD1_DATA6_USDHC1_DATA6 0xdf |
| MX8MQ_IOMUXC_SD1_DATA7_USDHC1_DATA7 0xdf |
| MX8MQ_IOMUXC_SD1_STROBE_USDHC1_STROBE 0x9f |
| MX8MQ_IOMUXC_SD1_RESET_B_USDHC1_RESET_B 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_gpio: usdhc2gpiogrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD2_CD_B_GPIO2_IO12 0x41 |
| MX8MQ_IOMUXC_SD2_WP_GPIO2_IO20 0x19 |
| >; |
| }; |
| |
| pinctrl_usdhc2: usdhc2grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x83 |
| MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xc3 |
| MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xc3 |
| MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xc3 |
| MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xc3 |
| MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xc3 |
| MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_100mhz: usdhc2-100grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x8d |
| MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xcd |
| MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xcd |
| MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xcd |
| MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xcd |
| MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xcd |
| MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usdhc2_200mhz: usdhc2-200grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_SD2_CLK_USDHC2_CLK 0x9f |
| MX8MQ_IOMUXC_SD2_CMD_USDHC2_CMD 0xdf |
| MX8MQ_IOMUXC_SD2_DATA0_USDHC2_DATA0 0xdf |
| MX8MQ_IOMUXC_SD2_DATA1_USDHC2_DATA1 0xdf |
| MX8MQ_IOMUXC_SD2_DATA2_USDHC2_DATA2 0xdf |
| MX8MQ_IOMUXC_SD2_DATA3_USDHC2_DATA3 0xdf |
| MX8MQ_IOMUXC_GPIO1_IO04_USDHC2_VSELECT 0xc1 |
| >; |
| }; |
| |
| pinctrl_usb0: usb0grp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_GPIO1_IO12_USB1_OTG_PWR 0x19 |
| MX8MQ_IOMUXC_GPIO1_IO13_USB1_OTG_OC 0x19 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX8MQ_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0xc6 |
| >; |
| }; |
| }; |
