| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * dts file for Xilinx ZynqMP |
| * |
| * (C) Copyright 2014 - 2021, Xilinx, Inc. |
| * |
| * Michal Simek <michal.simek@amd.com> |
| * |
| * This program is free software; you can redistribute it and/or |
| * modify it under the terms of the GNU General Public License as |
| * published by the Free Software Foundation; either version 2 of |
| * the License, or (at your option) any later version. |
| */ |
| |
| #include <dt-bindings/dma/xlnx-zynqmp-dpdma.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/power/xlnx-zynqmp-power.h> |
| #include <dt-bindings/reset/xlnx-zynqmp-resets.h> |
| |
| / { |
| compatible = "xlnx,zynqmp"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| operating-points-v2 = <&cpu_opp_table>; |
| reg = <0x0>; |
| cpu-idle-states = <&CPU_SLEEP_0>; |
| next-level-cache = <&L2>; |
| }; |
| |
| cpu1: cpu@1 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x1>; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-idle-states = <&CPU_SLEEP_0>; |
| next-level-cache = <&L2>; |
| }; |
| |
| cpu2: cpu@2 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x2>; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-idle-states = <&CPU_SLEEP_0>; |
| next-level-cache = <&L2>; |
| }; |
| |
| cpu3: cpu@3 { |
| compatible = "arm,cortex-a53"; |
| device_type = "cpu"; |
| enable-method = "psci"; |
| reg = <0x3>; |
| operating-points-v2 = <&cpu_opp_table>; |
| cpu-idle-states = <&CPU_SLEEP_0>; |
| next-level-cache = <&L2>; |
| }; |
| |
| L2: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| cache-unified; |
| }; |
| |
| idle-states { |
| entry-method = "psci"; |
| |
| CPU_SLEEP_0: cpu-sleep-0 { |
| compatible = "arm,idle-state"; |
| arm,psci-suspend-param = <0x40000000>; |
| local-timer-stop; |
| entry-latency-us = <300>; |
| exit-latency-us = <600>; |
| min-residency-us = <10000>; |
| }; |
| }; |
| }; |
| |
| cpu_opp_table: opp-table-cpu { |
| compatible = "operating-points-v2"; |
| opp-shared; |
| opp00 { |
| opp-hz = /bits/ 64 <1199999988>; |
| opp-microvolt = <1000000>; |
| clock-latency-ns = <500000>; |
| }; |
| opp01 { |
| opp-hz = /bits/ 64 <599999994>; |
| opp-microvolt = <1000000>; |
| clock-latency-ns = <500000>; |
| }; |
| opp02 { |
| opp-hz = /bits/ 64 <399999996>; |
| opp-microvolt = <1000000>; |
| clock-latency-ns = <500000>; |
| }; |
| opp03 { |
| opp-hz = /bits/ 64 <299999997>; |
| opp-microvolt = <1000000>; |
| clock-latency-ns = <500000>; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| rproc_0_fw_image: memory@3ed00000 { |
| no-map; |
| reg = <0x0 0x3ed00000 0x0 0x40000>; |
| }; |
| |
| rproc_1_fw_image: memory@3ef00000 { |
| no-map; |
| reg = <0x0 0x3ef00000 0x0 0x40000>; |
| }; |
| }; |
| |
| zynqmp_ipi: zynqmp-ipi { |
| bootph-all; |
| compatible = "xlnx,zynqmp-ipi-mailbox"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| xlnx,ipi-id = <0>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| ipi_mailbox_pmu1: mailbox@ff9905c0 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-ipi-dest-mailbox"; |
| reg = <0x0 0xff9905c0 0x0 0x20>, |
| <0x0 0xff9905e0 0x0 0x20>, |
| <0x0 0xff990e80 0x0 0x20>, |
| <0x0 0xff990ea0 0x0 0x20>; |
| reg-names = "local_request_region", |
| "local_response_region", |
| "remote_request_region", |
| "remote_response_region"; |
| #mbox-cells = <1>; |
| xlnx,ipi-id = <4>; |
| }; |
| }; |
| |
| dcc: dcc { |
| compatible = "arm,dcc"; |
| status = "disabled"; |
| bootph-all; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-affinity = <&cpu0>, |
| <&cpu1>, |
| <&cpu2>, |
| <&cpu3>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-0.2"; |
| method = "smc"; |
| }; |
| |
| firmware { |
| zynqmp_firmware: zynqmp-firmware { |
| compatible = "xlnx,zynqmp-firmware"; |
| #power-domain-cells = <1>; |
| method = "smc"; |
| bootph-all; |
| |
| zynqmp_power: zynqmp-power { |
| bootph-all; |
| compatible = "xlnx,zynqmp-power"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| mboxes = <&ipi_mailbox_pmu1 0>, <&ipi_mailbox_pmu1 1>; |
| mbox-names = "tx", "rx"; |
| }; |
| |
| nvmem-firmware { |
| compatible = "xlnx,zynqmp-nvmem-fw"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| soc_revision: soc-revision@0 { |
| reg = <0x0 0x4>; |
| }; |
| }; |
| |
| zynqmp_pcap: pcap { |
| compatible = "xlnx,zynqmp-pcap-fpga"; |
| }; |
| |
| xlnx_aes: zynqmp-aes { |
| compatible = "xlnx,zynqmp-aes"; |
| }; |
| |
| zynqmp_reset: reset-controller { |
| compatible = "xlnx,zynqmp-reset"; |
| #reset-cells = <1>; |
| }; |
| |
| pinctrl0: pinctrl { |
| compatible = "xlnx,zynqmp-pinctrl"; |
| status = "disabled"; |
| }; |
| |
| modepin_gpio: gpio { |
| compatible = "xlnx,zynqmp-gpio-modepin"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| |
| fpga_full: fpga-full { |
| compatible = "fpga-region"; |
| fpga-mgr = <&zynqmp_pcap>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| }; |
| |
| remoteproc { |
| compatible = "xlnx,zynqmp-r5fss"; |
| xlnx,cluster-mode = <1>; |
| |
| r5f-0 { |
| compatible = "xlnx,zynqmp-r5f"; |
| power-domains = <&zynqmp_firmware PD_RPU_0>; |
| memory-region = <&rproc_0_fw_image>; |
| }; |
| |
| r5f-1 { |
| compatible = "xlnx,zynqmp-r5f"; |
| power-domains = <&zynqmp_firmware PD_RPU_1>; |
| memory-region = <&rproc_1_fw_image>; |
| }; |
| }; |
| |
| amba: axi { |
| compatible = "simple-bus"; |
| bootph-all; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| can0: can@ff060000 { |
| compatible = "xlnx,zynq-can-1.0"; |
| status = "disabled"; |
| clock-names = "can_clk", "pclk"; |
| reg = <0x0 0xff060000 0x0 0x1000>; |
| interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| tx-fifo-depth = <0x40>; |
| rx-fifo-depth = <0x40>; |
| power-domains = <&zynqmp_firmware PD_CAN_0>; |
| }; |
| |
| can1: can@ff070000 { |
| compatible = "xlnx,zynq-can-1.0"; |
| status = "disabled"; |
| clock-names = "can_clk", "pclk"; |
| reg = <0x0 0xff070000 0x0 0x1000>; |
| interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| tx-fifo-depth = <0x40>; |
| rx-fifo-depth = <0x40>; |
| power-domains = <&zynqmp_firmware PD_CAN_1>; |
| }; |
| |
| cci: cci@fd6e0000 { |
| compatible = "arm,cci-400"; |
| status = "disabled"; |
| reg = <0x0 0xfd6e0000 0x0 0x9000>; |
| ranges = <0x0 0x0 0xfd6e0000 0x10000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| pmu@9000 { |
| compatible = "arm,cci-400-pmu,r1"; |
| reg = <0x9000 0x5000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| }; |
| |
| /* GDMA */ |
| fpd_dma_chan1: dma-controller@fd500000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd500000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14e8>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan2: dma-controller@fd510000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd510000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14e9>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan3: dma-controller@fd520000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd520000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14ea>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan4: dma-controller@fd530000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd530000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14eb>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan5: dma-controller@fd540000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd540000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14ec>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan6: dma-controller@fd550000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd550000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14ed>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan7: dma-controller@fd560000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd560000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14ee>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| fpd_dma_chan8: dma-controller@fd570000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xfd570000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <128>; |
| iommus = <&smmu 0x14ef>; |
| power-domains = <&zynqmp_firmware PD_GDMA>; |
| }; |
| |
| gic: interrupt-controller@f9010000 { |
| compatible = "arm,gic-400"; |
| #interrupt-cells = <3>; |
| reg = <0x0 0xf9010000 0x0 0x10000>, |
| <0x0 0xf9020000 0x0 0x20000>, |
| <0x0 0xf9040000 0x0 0x20000>, |
| <0x0 0xf9060000 0x0 0x20000>; |
| interrupt-controller; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; |
| }; |
| |
| gpu: gpu@fd4b0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-mali", "arm,mali-400"; |
| reg = <0x0 0xfd4b0000 0x0 0x10000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "gp", "gpmmu", "pp0", "ppmmu0", "pp1", "ppmmu1"; |
| clock-names = "bus", "core"; |
| power-domains = <&zynqmp_firmware PD_GPU>; |
| }; |
| |
| /* LPDDMA default allows only secured access. inorder to enable |
| * These dma channels, Users should ensure that these dma |
| * Channels are allowed for non secure access. |
| */ |
| lpd_dma_chan1: dma-controller@ffa80000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffa80000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x868>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan2: dma-controller@ffa90000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffa90000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x869>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan3: dma-controller@ffaa0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffaa0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86a>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan4: dma-controller@ffab0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffab0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86b>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan5: dma-controller@ffac0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffac0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86c>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan6: dma-controller@ffad0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffad0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86d>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan7: dma-controller@ffae0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffae0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86e>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| lpd_dma_chan8: dma-controller@ffaf0000 { |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dma-1.0"; |
| reg = <0x0 0xffaf0000 0x0 0x1000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "clk_main", "clk_apb"; |
| #dma-cells = <1>; |
| xlnx,bus-width = <64>; |
| iommus = <&smmu 0x86f>; |
| power-domains = <&zynqmp_firmware PD_ADMA>; |
| }; |
| |
| mc: memory-controller@fd070000 { |
| compatible = "xlnx,zynqmp-ddrc-2.40a"; |
| reg = <0x0 0xfd070000 0x0 0x30000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| nand0: nand-controller@ff100000 { |
| compatible = "xlnx,zynqmp-nand-controller", "arasan,nfc-v3p10"; |
| status = "disabled"; |
| reg = <0x0 0xff100000 0x0 0x1000>; |
| clock-names = "controller", "bus"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| iommus = <&smmu 0x872>; |
| power-domains = <&zynqmp_firmware PD_NAND>; |
| }; |
| |
| gem0: ethernet@ff0b0000 { |
| compatible = "xlnx,zynqmp-gem", "cdns,gem"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0b0000 0x0 0x1000>; |
| clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; |
| iommus = <&smmu 0x874>; |
| power-domains = <&zynqmp_firmware PD_ETH_0>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_GEM0>; |
| reset-names = "gem0_rst"; |
| }; |
| |
| gem1: ethernet@ff0c0000 { |
| compatible = "xlnx,zynqmp-gem", "cdns,gem"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0c0000 0x0 0x1000>; |
| clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; |
| iommus = <&smmu 0x875>; |
| power-domains = <&zynqmp_firmware PD_ETH_1>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_GEM1>; |
| reset-names = "gem1_rst"; |
| }; |
| |
| gem2: ethernet@ff0d0000 { |
| compatible = "xlnx,zynqmp-gem", "cdns,gem"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0d0000 0x0 0x1000>; |
| clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; |
| iommus = <&smmu 0x876>; |
| power-domains = <&zynqmp_firmware PD_ETH_2>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_GEM2>; |
| reset-names = "gem2_rst"; |
| }; |
| |
| gem3: ethernet@ff0e0000 { |
| compatible = "xlnx,zynqmp-gem", "cdns,gem"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff0e0000 0x0 0x1000>; |
| clock-names = "pclk", "hclk", "tx_clk", "rx_clk", "tsu_clk"; |
| iommus = <&smmu 0x877>; |
| power-domains = <&zynqmp_firmware PD_ETH_3>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_GEM3>; |
| reset-names = "gem3_rst"; |
| }; |
| |
| gpio: gpio@ff0a0000 { |
| compatible = "xlnx,zynqmp-gpio-1.0"; |
| status = "disabled"; |
| #gpio-cells = <0x2>; |
| gpio-controller; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| reg = <0x0 0xff0a0000 0x0 0x1000>; |
| power-domains = <&zynqmp_firmware PD_GPIO>; |
| }; |
| |
| i2c0: i2c@ff020000 { |
| compatible = "cdns,i2c-r1p14"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <400000>; |
| reg = <0x0 0xff020000 0x0 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&zynqmp_firmware PD_I2C_0>; |
| }; |
| |
| i2c1: i2c@ff030000 { |
| compatible = "cdns,i2c-r1p14"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; |
| clock-frequency = <400000>; |
| reg = <0x0 0xff030000 0x0 0x1000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&zynqmp_firmware PD_I2C_1>; |
| }; |
| |
| pcie: pcie@fd0e0000 { |
| compatible = "xlnx,nwl-pcie-2.11"; |
| status = "disabled"; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| msi-controller; |
| device_type = "pci"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, /* MSI_1 [63...32] */ |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; /* MSI_0 [31...0] */ |
| interrupt-names = "misc", "dummy", "intx", |
| "msi1", "msi0"; |
| msi-parent = <&pcie>; |
| reg = <0x0 0xfd0e0000 0x0 0x1000>, |
| <0x0 0xfd480000 0x0 0x1000>, |
| <0x80 0x00000000 0x0 0x1000000>; |
| reg-names = "breg", "pcireg", "cfg"; |
| ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 0xe0000000 0x00000000 0x10000000>,/* non-prefetchable memory */ |
| <0x43000000 0x00000006 0x00000000 0x00000006 0x00000000 0x00000002 0x00000000>;/* prefetchable memory */ |
| bus-range = <0x00 0xff>; |
| interrupt-map-mask = <0x0 0x0 0x0 0x7>; |
| interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, |
| <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, |
| <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, |
| <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; |
| iommus = <&smmu 0x4d0>; |
| power-domains = <&zynqmp_firmware PD_PCIE>; |
| pcie_intc: legacy-interrupt-controller { |
| interrupt-controller; |
| #address-cells = <0>; |
| #interrupt-cells = <1>; |
| }; |
| }; |
| |
| qspi: spi@ff0f0000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-qspi-1.0"; |
| status = "disabled"; |
| clock-names = "ref_clk", "pclk"; |
| interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| num-cs = <1>; |
| reg = <0x0 0xff0f0000 0x0 0x1000>, |
| <0x0 0xc0000000 0x0 0x8000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| iommus = <&smmu 0x873>; |
| power-domains = <&zynqmp_firmware PD_QSPI>; |
| }; |
| |
| psgtr: phy@fd400000 { |
| compatible = "xlnx,zynqmp-psgtr-v1.1"; |
| status = "disabled"; |
| reg = <0x0 0xfd400000 0x0 0x40000>, |
| <0x0 0xfd3d0000 0x0 0x1000>; |
| reg-names = "serdes", "siou"; |
| #phy-cells = <4>; |
| }; |
| |
| rtc: rtc@ffa60000 { |
| compatible = "xlnx,zynqmp-rtc"; |
| status = "disabled"; |
| reg = <0x0 0xffa60000 0x0 0x100>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "alarm", "sec"; |
| calibration = <0x7FFF>; |
| }; |
| |
| sata: ahci@fd0c0000 { |
| compatible = "ceva,ahci-1v84"; |
| status = "disabled"; |
| reg = <0x0 0xfd0c0000 0x0 0x2000>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; |
| power-domains = <&zynqmp_firmware PD_SATA>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_SATA>; |
| iommus = <&smmu 0x4c0>, <&smmu 0x4c1>, |
| <&smmu 0x4c2>, <&smmu 0x4c3>; |
| }; |
| |
| sdhci0: mmc@ff160000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff160000 0x0 0x1000>; |
| clock-names = "clk_xin", "clk_ahb"; |
| iommus = <&smmu 0x870>; |
| #clock-cells = <1>; |
| clock-output-names = "clk_out_sd0", "clk_in_sd0"; |
| power-domains = <&zynqmp_firmware PD_SD_0>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_SDIO0>; |
| }; |
| |
| sdhci1: mmc@ff170000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-8.9a", "arasan,sdhci-8.9a"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff170000 0x0 0x1000>; |
| clock-names = "clk_xin", "clk_ahb"; |
| iommus = <&smmu 0x871>; |
| #clock-cells = <1>; |
| clock-output-names = "clk_out_sd1", "clk_in_sd1"; |
| power-domains = <&zynqmp_firmware PD_SD_1>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_SDIO1>; |
| }; |
| |
| smmu: iommu@fd800000 { |
| compatible = "arm,mmu-500"; |
| reg = <0x0 0xfd800000 0x0 0x20000>; |
| #iommu-cells = <1>; |
| status = "disabled"; |
| #global-interrupts = <1>; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 155 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| spi0: spi@ff040000 { |
| compatible = "cdns,spi-r1p6"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff040000 0x0 0x1000>; |
| clock-names = "ref_clk", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&zynqmp_firmware PD_SPI_0>; |
| }; |
| |
| spi1: spi@ff050000 { |
| compatible = "cdns,spi-r1p6"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff050000 0x0 0x1000>; |
| clock-names = "ref_clk", "pclk"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| power-domains = <&zynqmp_firmware PD_SPI_1>; |
| }; |
| |
| ttc0: timer@ff110000 { |
| compatible = "cdns,ttc"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff110000 0x0 0x1000>; |
| timer-width = <32>; |
| power-domains = <&zynqmp_firmware PD_TTC_0>; |
| }; |
| |
| ttc1: timer@ff120000 { |
| compatible = "cdns,ttc"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff120000 0x0 0x1000>; |
| timer-width = <32>; |
| power-domains = <&zynqmp_firmware PD_TTC_1>; |
| }; |
| |
| ttc2: timer@ff130000 { |
| compatible = "cdns,ttc"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff130000 0x0 0x1000>; |
| timer-width = <32>; |
| power-domains = <&zynqmp_firmware PD_TTC_2>; |
| }; |
| |
| ttc3: timer@ff140000 { |
| compatible = "cdns,ttc"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff140000 0x0 0x1000>; |
| timer-width = <32>; |
| power-domains = <&zynqmp_firmware PD_TTC_3>; |
| }; |
| |
| uart0: serial@ff000000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff000000 0x0 0x1000>; |
| clock-names = "uart_clk", "pclk"; |
| power-domains = <&zynqmp_firmware PD_UART_0>; |
| }; |
| |
| uart1: serial@ff010000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-uart", "cdns,uart-r1p12"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xff010000 0x0 0x1000>; |
| clock-names = "uart_clk", "pclk"; |
| power-domains = <&zynqmp_firmware PD_UART_1>; |
| }; |
| |
| usb0: usb@ff9d0000 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dwc3"; |
| reg = <0x0 0xff9d0000 0x0 0x100>; |
| power-domains = <&zynqmp_firmware PD_USB_0>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_USB0_CORERESET>, |
| <&zynqmp_reset ZYNQMP_RESET_USB0_HIBERRESET>, |
| <&zynqmp_reset ZYNQMP_RESET_USB0_APB>; |
| reset-names = "usb_crst", "usb_hibrst", "usb_apbrst"; |
| reset-gpios = <&modepin_gpio 1 GPIO_ACTIVE_LOW>; |
| ranges; |
| |
| dwc3_0: usb@fe200000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0xfe200000 0x0 0x40000>; |
| interrupt-parent = <&gic>; |
| interrupt-names = "host", "peripheral", "otg"; |
| interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "bus_early", "ref"; |
| iommus = <&smmu 0x860>; |
| snps,quirk-frame-length-adjustment = <0x20>; |
| snps,resume-hs-terminations; |
| /* dma-coherent; */ |
| }; |
| }; |
| |
| usb1: usb@ff9e0000 { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| status = "disabled"; |
| compatible = "xlnx,zynqmp-dwc3"; |
| reg = <0x0 0xff9e0000 0x0 0x100>; |
| power-domains = <&zynqmp_firmware PD_USB_1>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_USB1_CORERESET>, |
| <&zynqmp_reset ZYNQMP_RESET_USB1_HIBERRESET>, |
| <&zynqmp_reset ZYNQMP_RESET_USB1_APB>; |
| reset-names = "usb_crst", "usb_hibrst", "usb_apbrst"; |
| ranges; |
| |
| dwc3_1: usb@fe300000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0xfe300000 0x0 0x40000>; |
| interrupt-parent = <&gic>; |
| interrupt-names = "host", "peripheral", "otg"; |
| interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "bus_early", "ref"; |
| iommus = <&smmu 0x861>; |
| snps,quirk-frame-length-adjustment = <0x20>; |
| snps,resume-hs-terminations; |
| /* dma-coherent; */ |
| }; |
| }; |
| |
| watchdog0: watchdog@fd4d0000 { |
| compatible = "cdns,wdt-r1p2"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 113 IRQ_TYPE_EDGE_RISING>; |
| reg = <0x0 0xfd4d0000 0x0 0x1000>; |
| timeout-sec = <60>; |
| reset-on-timeout; |
| }; |
| |
| lpd_watchdog: watchdog@ff150000 { |
| compatible = "cdns,wdt-r1p2"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 52 IRQ_TYPE_EDGE_RISING>; |
| reg = <0x0 0xff150000 0x0 0x1000>; |
| timeout-sec = <10>; |
| }; |
| |
| xilinx_ams: ams@ffa50000 { |
| compatible = "xlnx,zynqmp-ams"; |
| status = "disabled"; |
| interrupt-parent = <&gic>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| reg = <0x0 0xffa50000 0x0 0x800>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #io-channel-cells = <1>; |
| ranges = <0 0 0xffa50800 0x800>; |
| |
| ams_ps: ams-ps@0 { |
| compatible = "xlnx,zynqmp-ams-ps"; |
| status = "disabled"; |
| reg = <0x0 0x400>; |
| }; |
| |
| ams_pl: ams-pl@400 { |
| compatible = "xlnx,zynqmp-ams-pl"; |
| status = "disabled"; |
| reg = <0x400 0x400>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| }; |
| }; |
| |
| zynqmp_dpdma: dma-controller@fd4c0000 { |
| compatible = "xlnx,zynqmp-dpdma"; |
| status = "disabled"; |
| reg = <0x0 0xfd4c0000 0x0 0x1000>; |
| interrupts = <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| clock-names = "axi_clk"; |
| power-domains = <&zynqmp_firmware PD_DP>; |
| #dma-cells = <1>; |
| }; |
| |
| zynqmp_dpsub: display@fd4a0000 { |
| bootph-all; |
| compatible = "xlnx,zynqmp-dpsub-1.7"; |
| status = "disabled"; |
| reg = <0x0 0xfd4a0000 0x0 0x1000>, |
| <0x0 0xfd4aa000 0x0 0x1000>, |
| <0x0 0xfd4ab000 0x0 0x1000>, |
| <0x0 0xfd4ac000 0x0 0x1000>; |
| reg-names = "dp", "blend", "av_buf", "aud"; |
| interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-parent = <&gic>; |
| clock-names = "dp_apb_clk", "dp_aud_clk", |
| "dp_vtc_pixel_clk_in"; |
| power-domains = <&zynqmp_firmware PD_DP>; |
| resets = <&zynqmp_reset ZYNQMP_RESET_DP>; |
| dma-names = "vid0", "vid1", "vid2", "gfx0"; |
| dmas = <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO0>, |
| <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO1>, |
| <&zynqmp_dpdma ZYNQMP_DPDMA_VIDEO2>, |
| <&zynqmp_dpdma ZYNQMP_DPDMA_GRAPHICS>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| }; |
| port@1 { |
| reg = <1>; |
| }; |
| port@2 { |
| reg = <2>; |
| }; |
| port@3 { |
| reg = <3>; |
| }; |
| port@4 { |
| reg = <4>; |
| }; |
| port@5 { |
| reg = <5>; |
| }; |
| }; |
| }; |
| }; |
| }; |
