blob: 3818c5e06ebac5099f8051c813222349a2f6a6a5 [file] [log] [blame]
config STMMAC_ETH
tristate "STMicroelectronics 10/100/1000 Ethernet driver"
depends on HAS_IOMEM && HAS_DMA
select MII
select PHYLIB
select CRC32
select PTP_1588_CLOCK
select RESET_CONTROLLER
---help---
This is the driver for the Ethernet IPs are built around a
Synopsys IP Core and only tested on the STMicroelectronics
platforms.
if STMMAC_ETH
config STMMAC_PLATFORM
tristate "STMMAC Platform bus support"
depends on STMMAC_ETH
select MFD_SYSCON
default y
---help---
This selects the platform specific bus support for the stmmac driver.
This is the driver used on several SoCs:
STi, Allwinner, Amlogic Meson, Altera SOCFPGA.
If you have a controller with this interface, say Y or M here.
If unsure, say N.
if STMMAC_PLATFORM
config DWMAC_GENERIC
tristate "Generic driver for DWMAC"
default STMMAC_PLATFORM
---help---
Generic DWMAC driver for platforms that don't require any
platform specific code to function or is using platform
data for setup.
config DWMAC_IPQ806X
tristate "QCA IPQ806x DWMAC support"
default ARCH_QCOM
depends on OF && (ARCH_QCOM || COMPILE_TEST)
select MFD_SYSCON
help
Support for QCA IPQ806X DWMAC Ethernet.
This selects the IPQ806x SoC glue layer support for the stmmac
device driver. This driver does not use any of the hardware
acceleration features available on this SoC. Network devices
will behave like standard non-accelerated ethernet interfaces.
config DWMAC_LPC18XX
tristate "NXP LPC18xx/43xx DWMAC support"
default ARCH_LPC18XX
depends on OF && (ARCH_LPC18XX || COMPILE_TEST)
select MFD_SYSCON
---help---
Support for NXP LPC18xx/43xx DWMAC Ethernet.
config DWMAC_MESON
tristate "Amlogic Meson dwmac support"
default ARCH_MESON
depends on OF && COMMON_CLK && (ARCH_MESON || COMPILE_TEST)
help
Support for Ethernet controller on Amlogic Meson SoCs.
This selects the Amlogic Meson SoC glue layer support for
the stmmac device driver. This driver is used for Meson6,
Meson8, Meson8b and GXBB SoCs.
config DWMAC_ROCKCHIP
tristate "Rockchip dwmac support"
default ARCH_ROCKCHIP
depends on OF && (ARCH_ROCKCHIP || COMPILE_TEST)
select MFD_SYSCON
help
Support for Ethernet controller on Rockchip RK3288 SoC.
This selects the Rockchip RK3288 SoC glue layer support for
the stmmac device driver.
config DWMAC_SOCFPGA
tristate "SOCFPGA dwmac support"
default ARCH_SOCFPGA
depends on OF && (ARCH_SOCFPGA || COMPILE_TEST)
select MFD_SYSCON
help
Support for ethernet controller on Altera SOCFPGA
This selects the Altera SOCFPGA SoC glue layer support
for the stmmac device driver. This driver is used for
arria5 and cyclone5 FPGA SoCs.
config DWMAC_STI
tristate "STi GMAC support"
default ARCH_STI
depends on OF && (ARCH_STI || COMPILE_TEST)
select MFD_SYSCON
---help---
Support for ethernet controller on STi SOCs.
This selects STi SoC glue layer support for the stmmac
device driver. This driver is used on for the STi series
SOCs GMAC ethernet controller.
config DWMAC_STM32
tristate "STM32 DWMAC support"
default ARCH_STM32
depends on OF && HAS_IOMEM
select MFD_SYSCON
---help---
Support for ethernet controller on STM32 SOCs.
This selects STM32 SoC glue layer support for the stmmac
device driver. This driver is used on for the STM32 series
SOCs GMAC ethernet controller.
config DWMAC_SUNXI
tristate "Allwinner GMAC support"
default ARCH_SUNXI
depends on OF && (ARCH_SUNXI || COMPILE_TEST)
---help---
Support for Allwinner A20/A31 GMAC ethernet controllers.
This selects Allwinner SoC glue layer support for the
stmmac device driver. This driver is used for A20/A31
GMAC ethernet controller.
endif
config STMMAC_PCI
tristate "STMMAC PCI bus support"
depends on STMMAC_ETH && PCI
---help---
This is to select the Synopsys DWMAC available on PCI devices,
if you have a controller with this interface, say Y or M here.
This PCI support is tested on XLINX XC2V3000 FF1152AMT0221
D1215994A VIRTEX FPGA board.
If unsure, say N.
endif