| // SPDX-License-Identifier: GPL-2.0 |
| // Copyright (c) 2022 Intel Corporation. |
| |
| #include <asm/unaligned.h> |
| #include <linux/acpi.h> |
| #include <linux/delay.h> |
| #include <linux/i2c.h> |
| #include <linux/module.h> |
| #include <linux/pm_runtime.h> |
| #include <media/v4l2-ctrls.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-fwnode.h> |
| |
| #define OG01A1B_REG_VALUE_08BIT 1 |
| #define OG01A1B_REG_VALUE_16BIT 2 |
| #define OG01A1B_REG_VALUE_24BIT 3 |
| |
| #define OG01A1B_LINK_FREQ_500MHZ 500000000ULL |
| #define OG01A1B_SCLK 120000000LL |
| #define OG01A1B_MCLK 19200000 |
| #define OG01A1B_DATA_LANES 2 |
| #define OG01A1B_RGB_DEPTH 10 |
| |
| #define OG01A1B_REG_CHIP_ID 0x300a |
| #define OG01A1B_CHIP_ID 0x470141 |
| |
| #define OG01A1B_REG_MODE_SELECT 0x0100 |
| #define OG01A1B_MODE_STANDBY 0x00 |
| #define OG01A1B_MODE_STREAMING 0x01 |
| |
| /* vertical-timings from sensor */ |
| #define OG01A1B_REG_VTS 0x380e |
| #define OG01A1B_VTS_120FPS 0x0498 |
| #define OG01A1B_VTS_120FPS_MIN 0x0498 |
| #define OG01A1B_VTS_MAX 0x7fff |
| |
| /* horizontal-timings from sensor */ |
| #define OG01A1B_REG_HTS 0x380c |
| |
| /* Exposure controls from sensor */ |
| #define OG01A1B_REG_EXPOSURE 0x3501 |
| #define OG01A1B_EXPOSURE_MIN 1 |
| #define OG01A1B_EXPOSURE_MAX_MARGIN 14 |
| #define OG01A1B_EXPOSURE_STEP 1 |
| |
| /* Analog gain controls from sensor */ |
| #define OG01A1B_REG_ANALOG_GAIN 0x3508 |
| #define OG01A1B_ANAL_GAIN_MIN 16 |
| #define OG01A1B_ANAL_GAIN_MAX 248 /* Max = 15.5x */ |
| #define OG01A1B_ANAL_GAIN_STEP 1 |
| |
| /* Digital gain controls from sensor */ |
| #define OG01A1B_REG_DIG_GAIN 0x350a |
| #define OG01A1B_DGTL_GAIN_MIN 1024 |
| #define OG01A1B_DGTL_GAIN_MAX 16384 /* Max = 16x */ |
| #define OG01A1B_DGTL_GAIN_STEP 1 |
| #define OG01A1B_DGTL_GAIN_DEFAULT 1024 |
| |
| /* Group Access */ |
| #define OG01A1B_REG_GROUP_ACCESS 0x3208 |
| #define OG01A1B_GROUP_HOLD_START 0x0 |
| #define OG01A1B_GROUP_HOLD_END 0x10 |
| #define OG01A1B_GROUP_HOLD_LAUNCH 0xa0 |
| |
| /* Test Pattern Control */ |
| #define OG01A1B_REG_TEST_PATTERN 0x5100 |
| #define OG01A1B_TEST_PATTERN_ENABLE BIT(7) |
| #define OG01A1B_TEST_PATTERN_BAR_SHIFT 2 |
| |
| #define to_og01a1b(_sd) container_of(_sd, struct og01a1b, sd) |
| |
| enum { |
| OG01A1B_LINK_FREQ_1000MBPS, |
| }; |
| |
| struct og01a1b_reg { |
| u16 address; |
| u8 val; |
| }; |
| |
| struct og01a1b_reg_list { |
| u32 num_of_regs; |
| const struct og01a1b_reg *regs; |
| }; |
| |
| struct og01a1b_link_freq_config { |
| const struct og01a1b_reg_list reg_list; |
| }; |
| |
| struct og01a1b_mode { |
| /* Frame width in pixels */ |
| u32 width; |
| |
| /* Frame height in pixels */ |
| u32 height; |
| |
| /* Horizontal timining size */ |
| u32 hts; |
| |
| /* Default vertical timining size */ |
| u32 vts_def; |
| |
| /* Min vertical timining size */ |
| u32 vts_min; |
| |
| /* Link frequency needed for this resolution */ |
| u32 link_freq_index; |
| |
| /* Sensor register settings for this resolution */ |
| const struct og01a1b_reg_list reg_list; |
| }; |
| |
| static const struct og01a1b_reg mipi_data_rate_1000mbps[] = { |
| {0x0103, 0x01}, |
| {0x0303, 0x02}, |
| {0x0304, 0x00}, |
| {0x0305, 0xd2}, |
| {0x0323, 0x02}, |
| {0x0324, 0x01}, |
| {0x0325, 0x77}, |
| }; |
| |
| static const struct og01a1b_reg mode_1280x1024_regs[] = { |
| {0x0300, 0x0a}, |
| {0x0301, 0x29}, |
| {0x0302, 0x31}, |
| {0x0303, 0x02}, |
| {0x0304, 0x00}, |
| {0x0305, 0xd2}, |
| {0x0306, 0x00}, |
| {0x0307, 0x01}, |
| {0x0308, 0x02}, |
| {0x0309, 0x00}, |
| {0x0310, 0x00}, |
| {0x0311, 0x00}, |
| {0x0312, 0x07}, |
| {0x0313, 0x00}, |
| {0x0314, 0x00}, |
| {0x0315, 0x00}, |
| {0x0320, 0x02}, |
| {0x0321, 0x01}, |
| {0x0322, 0x01}, |
| {0x0323, 0x02}, |
| {0x0324, 0x01}, |
| {0x0325, 0x77}, |
| {0x0326, 0xce}, |
| {0x0327, 0x04}, |
| {0x0329, 0x02}, |
| {0x032a, 0x04}, |
| {0x032b, 0x04}, |
| {0x032c, 0x02}, |
| {0x032d, 0x01}, |
| {0x032e, 0x00}, |
| {0x300d, 0x02}, |
| {0x300e, 0x04}, |
| {0x3021, 0x08}, |
| {0x301e, 0x03}, |
| {0x3103, 0x00}, |
| {0x3106, 0x08}, |
| {0x3107, 0x40}, |
| {0x3216, 0x01}, |
| {0x3217, 0x00}, |
| {0x3218, 0xc0}, |
| {0x3219, 0x55}, |
| {0x3500, 0x00}, |
| {0x3501, 0x04}, |
| {0x3502, 0x8a}, |
| {0x3506, 0x01}, |
| {0x3507, 0x72}, |
| {0x3508, 0x01}, |
| {0x3509, 0x00}, |
| {0x350a, 0x01}, |
| {0x350b, 0x00}, |
| {0x350c, 0x00}, |
| {0x3541, 0x00}, |
| {0x3542, 0x40}, |
| {0x3605, 0xe0}, |
| {0x3606, 0x41}, |
| {0x3614, 0x20}, |
| {0x3620, 0x0b}, |
| {0x3630, 0x07}, |
| {0x3636, 0xa0}, |
| {0x3637, 0xf9}, |
| {0x3638, 0x09}, |
| {0x3639, 0x38}, |
| {0x363f, 0x09}, |
| {0x3640, 0x17}, |
| {0x3662, 0x04}, |
| {0x3665, 0x80}, |
| {0x3670, 0x68}, |
| {0x3674, 0x00}, |
| {0x3677, 0x3f}, |
| {0x3679, 0x00}, |
| {0x369f, 0x19}, |
| {0x36a0, 0x03}, |
| {0x36a2, 0x19}, |
| {0x36a3, 0x03}, |
| {0x370d, 0x66}, |
| {0x370f, 0x00}, |
| {0x3710, 0x03}, |
| {0x3715, 0x03}, |
| {0x3716, 0x03}, |
| {0x3717, 0x06}, |
| {0x3733, 0x00}, |
| {0x3778, 0x00}, |
| {0x37a8, 0x0f}, |
| {0x37a9, 0x01}, |
| {0x37aa, 0x07}, |
| {0x37bd, 0x1c}, |
| {0x37c1, 0x2f}, |
| {0x37c3, 0x09}, |
| {0x37c8, 0x1d}, |
| {0x37ca, 0x30}, |
| {0x37df, 0x00}, |
| {0x3800, 0x00}, |
| {0x3801, 0x00}, |
| {0x3802, 0x00}, |
| {0x3803, 0x00}, |
| {0x3804, 0x05}, |
| {0x3805, 0x0f}, |
| {0x3806, 0x04}, |
| {0x3807, 0x0f}, |
| {0x3808, 0x05}, |
| {0x3809, 0x00}, |
| {0x380a, 0x04}, |
| {0x380b, 0x00}, |
| {0x380c, 0x03}, |
| {0x380d, 0x50}, |
| {0x380e, 0x04}, |
| {0x380f, 0x98}, |
| {0x3810, 0x00}, |
| {0x3811, 0x08}, |
| {0x3812, 0x00}, |
| {0x3813, 0x08}, |
| {0x3814, 0x11}, |
| {0x3815, 0x11}, |
| {0x3820, 0x40}, |
| {0x3821, 0x04}, |
| {0x3826, 0x00}, |
| {0x3827, 0x00}, |
| {0x382a, 0x08}, |
| {0x382b, 0x52}, |
| {0x382d, 0xba}, |
| {0x383d, 0x14}, |
| {0x384a, 0xa2}, |
| {0x3866, 0x0e}, |
| {0x3867, 0x07}, |
| {0x3884, 0x00}, |
| {0x3885, 0x08}, |
| {0x3893, 0x68}, |
| {0x3894, 0x2a}, |
| {0x3898, 0x00}, |
| {0x3899, 0x31}, |
| {0x389a, 0x04}, |
| {0x389b, 0x00}, |
| {0x389c, 0x0b}, |
| {0x389d, 0xad}, |
| {0x389f, 0x08}, |
| {0x38a0, 0x00}, |
| {0x38a1, 0x00}, |
| {0x38a8, 0x70}, |
| {0x38ac, 0xea}, |
| {0x38b2, 0x00}, |
| {0x38b3, 0x08}, |
| {0x38bc, 0x20}, |
| {0x38c4, 0x0c}, |
| {0x38c5, 0x3a}, |
| {0x38c7, 0x3a}, |
| {0x38e1, 0xc0}, |
| {0x38ec, 0x3c}, |
| {0x38f0, 0x09}, |
| {0x38f1, 0x6f}, |
| {0x38fe, 0x3c}, |
| {0x391e, 0x00}, |
| {0x391f, 0x00}, |
| {0x3920, 0xa5}, |
| {0x3921, 0x00}, |
| {0x3922, 0x00}, |
| {0x3923, 0x00}, |
| {0x3924, 0x05}, |
| {0x3925, 0x00}, |
| {0x3926, 0x00}, |
| {0x3927, 0x00}, |
| {0x3928, 0x1a}, |
| {0x3929, 0x01}, |
| {0x392a, 0xb4}, |
| {0x392b, 0x00}, |
| {0x392c, 0x10}, |
| {0x392f, 0x40}, |
| {0x4000, 0xcf}, |
| {0x4003, 0x40}, |
| {0x4008, 0x00}, |
| {0x4009, 0x07}, |
| {0x400a, 0x02}, |
| {0x400b, 0x54}, |
| {0x400c, 0x00}, |
| {0x400d, 0x07}, |
| {0x4010, 0xc0}, |
| {0x4012, 0x02}, |
| {0x4014, 0x04}, |
| {0x4015, 0x04}, |
| {0x4017, 0x02}, |
| {0x4042, 0x01}, |
| {0x4306, 0x04}, |
| {0x4307, 0x12}, |
| {0x4509, 0x00}, |
| {0x450b, 0x83}, |
| {0x4604, 0x68}, |
| {0x4608, 0x0a}, |
| {0x4700, 0x06}, |
| {0x4800, 0x64}, |
| {0x481b, 0x3c}, |
| {0x4825, 0x32}, |
| {0x4833, 0x18}, |
| {0x4837, 0x0f}, |
| {0x4850, 0x40}, |
| {0x4860, 0x00}, |
| {0x4861, 0xec}, |
| {0x4864, 0x00}, |
| {0x4883, 0x00}, |
| {0x4888, 0x90}, |
| {0x4889, 0x05}, |
| {0x488b, 0x04}, |
| {0x4f00, 0x04}, |
| {0x4f10, 0x04}, |
| {0x4f21, 0x01}, |
| {0x4f22, 0x40}, |
| {0x4f23, 0x44}, |
| {0x4f24, 0x51}, |
| {0x4f25, 0x41}, |
| {0x5000, 0x1f}, |
| {0x500a, 0x00}, |
| {0x5100, 0x00}, |
| {0x5111, 0x20}, |
| {0x3020, 0x20}, |
| {0x3613, 0x03}, |
| {0x38c9, 0x02}, |
| {0x5304, 0x01}, |
| {0x3620, 0x08}, |
| {0x3639, 0x58}, |
| {0x363a, 0x10}, |
| {0x3674, 0x04}, |
| {0x3780, 0xff}, |
| {0x3781, 0xff}, |
| {0x3782, 0x00}, |
| {0x3783, 0x01}, |
| {0x3798, 0xa3}, |
| {0x37aa, 0x10}, |
| {0x38a8, 0xf0}, |
| {0x38c4, 0x09}, |
| {0x38c5, 0xb0}, |
| {0x38df, 0x80}, |
| {0x38ff, 0x05}, |
| {0x4010, 0xf1}, |
| {0x4011, 0x70}, |
| {0x3667, 0x80}, |
| {0x4d00, 0x4a}, |
| {0x4d01, 0x18}, |
| {0x4d02, 0xbb}, |
| {0x4d03, 0xde}, |
| {0x4d04, 0x93}, |
| {0x4d05, 0xff}, |
| {0x4d09, 0x0a}, |
| {0x37aa, 0x16}, |
| {0x3606, 0x42}, |
| {0x3605, 0x00}, |
| {0x36a2, 0x17}, |
| {0x300d, 0x0a}, |
| {0x4d00, 0x4d}, |
| {0x4d01, 0x95}, |
| {0x3d8C, 0x70}, |
| {0x3d8d, 0xE9}, |
| {0x5300, 0x00}, |
| {0x5301, 0x10}, |
| {0x5302, 0x00}, |
| {0x5303, 0xE3}, |
| {0x3d88, 0x00}, |
| {0x3d89, 0x10}, |
| {0x3d8a, 0x00}, |
| {0x3d8b, 0xE3}, |
| {0x4f22, 0x00}, |
| }; |
| |
| static const char * const og01a1b_test_pattern_menu[] = { |
| "Disabled", |
| "Standard Color Bar", |
| "Top-Bottom Darker Color Bar", |
| "Right-Left Darker Color Bar", |
| "Bottom-Top Darker Color Bar" |
| }; |
| |
| static const s64 link_freq_menu_items[] = { |
| OG01A1B_LINK_FREQ_500MHZ, |
| }; |
| |
| static const struct og01a1b_link_freq_config link_freq_configs[] = { |
| [OG01A1B_LINK_FREQ_1000MBPS] = { |
| .reg_list = { |
| .num_of_regs = ARRAY_SIZE(mipi_data_rate_1000mbps), |
| .regs = mipi_data_rate_1000mbps, |
| } |
| } |
| }; |
| |
| static const struct og01a1b_mode supported_modes[] = { |
| { |
| .width = 1280, |
| .height = 1024, |
| .hts = 848, |
| .vts_def = OG01A1B_VTS_120FPS, |
| .vts_min = OG01A1B_VTS_120FPS_MIN, |
| .reg_list = { |
| .num_of_regs = ARRAY_SIZE(mode_1280x1024_regs), |
| .regs = mode_1280x1024_regs, |
| }, |
| .link_freq_index = OG01A1B_LINK_FREQ_1000MBPS, |
| }, |
| }; |
| |
| struct og01a1b { |
| struct v4l2_subdev sd; |
| struct media_pad pad; |
| struct v4l2_ctrl_handler ctrl_handler; |
| |
| /* V4L2 Controls */ |
| struct v4l2_ctrl *link_freq; |
| struct v4l2_ctrl *pixel_rate; |
| struct v4l2_ctrl *vblank; |
| struct v4l2_ctrl *hblank; |
| struct v4l2_ctrl *exposure; |
| |
| /* Current mode */ |
| const struct og01a1b_mode *cur_mode; |
| |
| /* To serialize asynchronus callbacks */ |
| struct mutex mutex; |
| |
| /* Streaming on/off */ |
| bool streaming; |
| }; |
| |
| static u64 to_pixel_rate(u32 f_index) |
| { |
| u64 pixel_rate = link_freq_menu_items[f_index] * 2 * OG01A1B_DATA_LANES; |
| |
| do_div(pixel_rate, OG01A1B_RGB_DEPTH); |
| |
| return pixel_rate; |
| } |
| |
| static u64 to_pixels_per_line(u32 hts, u32 f_index) |
| { |
| u64 ppl = hts * to_pixel_rate(f_index); |
| |
| do_div(ppl, OG01A1B_SCLK); |
| |
| return ppl; |
| } |
| |
| static int og01a1b_read_reg(struct og01a1b *og01a1b, u16 reg, u16 len, u32 *val) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| struct i2c_msg msgs[2]; |
| u8 addr_buf[2]; |
| u8 data_buf[4] = {0}; |
| int ret; |
| |
| if (len > 4) |
| return -EINVAL; |
| |
| put_unaligned_be16(reg, addr_buf); |
| msgs[0].addr = client->addr; |
| msgs[0].flags = 0; |
| msgs[0].len = sizeof(addr_buf); |
| msgs[0].buf = addr_buf; |
| msgs[1].addr = client->addr; |
| msgs[1].flags = I2C_M_RD; |
| msgs[1].len = len; |
| msgs[1].buf = &data_buf[4 - len]; |
| |
| ret = i2c_transfer(client->adapter, msgs, ARRAY_SIZE(msgs)); |
| if (ret != ARRAY_SIZE(msgs)) |
| return -EIO; |
| |
| *val = get_unaligned_be32(data_buf); |
| |
| return 0; |
| } |
| |
| static int og01a1b_write_reg(struct og01a1b *og01a1b, u16 reg, u16 len, u32 val) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| u8 buf[6]; |
| |
| if (len > 4) |
| return -EINVAL; |
| |
| put_unaligned_be16(reg, buf); |
| put_unaligned_be32(val << 8 * (4 - len), buf + 2); |
| if (i2c_master_send(client, buf, len + 2) != len + 2) |
| return -EIO; |
| |
| return 0; |
| } |
| |
| static int og01a1b_write_reg_list(struct og01a1b *og01a1b, |
| const struct og01a1b_reg_list *r_list) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| unsigned int i; |
| int ret; |
| |
| for (i = 0; i < r_list->num_of_regs; i++) { |
| ret = og01a1b_write_reg(og01a1b, r_list->regs[i].address, 1, |
| r_list->regs[i].val); |
| if (ret) { |
| dev_err_ratelimited(&client->dev, |
| "failed to write reg 0x%4.4x. error = %d", |
| r_list->regs[i].address, ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int og01a1b_test_pattern(struct og01a1b *og01a1b, u32 pattern) |
| { |
| if (pattern) |
| pattern = (pattern - 1) << OG01A1B_TEST_PATTERN_BAR_SHIFT | |
| OG01A1B_TEST_PATTERN_ENABLE; |
| |
| return og01a1b_write_reg(og01a1b, OG01A1B_REG_TEST_PATTERN, |
| OG01A1B_REG_VALUE_08BIT, pattern); |
| } |
| |
| static int og01a1b_set_ctrl(struct v4l2_ctrl *ctrl) |
| { |
| struct og01a1b *og01a1b = container_of(ctrl->handler, |
| struct og01a1b, ctrl_handler); |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| s64 exposure_max; |
| int ret = 0; |
| |
| /* Propagate change of current control to all related controls */ |
| if (ctrl->id == V4L2_CID_VBLANK) { |
| /* Update max exposure while meeting expected vblanking */ |
| exposure_max = og01a1b->cur_mode->height + ctrl->val - |
| OG01A1B_EXPOSURE_MAX_MARGIN; |
| __v4l2_ctrl_modify_range(og01a1b->exposure, |
| og01a1b->exposure->minimum, |
| exposure_max, og01a1b->exposure->step, |
| exposure_max); |
| } |
| |
| /* V4L2 controls values will be applied only when power is already up */ |
| if (!pm_runtime_get_if_in_use(&client->dev)) |
| return 0; |
| |
| switch (ctrl->id) { |
| case V4L2_CID_ANALOGUE_GAIN: |
| ret = og01a1b_write_reg(og01a1b, OG01A1B_REG_ANALOG_GAIN, |
| OG01A1B_REG_VALUE_16BIT, |
| ctrl->val << 4); |
| break; |
| |
| case V4L2_CID_DIGITAL_GAIN: |
| ret = og01a1b_write_reg(og01a1b, OG01A1B_REG_DIG_GAIN, |
| OG01A1B_REG_VALUE_24BIT, |
| ctrl->val << 6); |
| break; |
| |
| case V4L2_CID_EXPOSURE: |
| ret = og01a1b_write_reg(og01a1b, OG01A1B_REG_EXPOSURE, |
| OG01A1B_REG_VALUE_16BIT, ctrl->val); |
| break; |
| |
| case V4L2_CID_VBLANK: |
| ret = og01a1b_write_reg(og01a1b, OG01A1B_REG_VTS, |
| OG01A1B_REG_VALUE_16BIT, |
| og01a1b->cur_mode->height + ctrl->val); |
| break; |
| |
| case V4L2_CID_TEST_PATTERN: |
| ret = og01a1b_test_pattern(og01a1b, ctrl->val); |
| break; |
| |
| default: |
| ret = -EINVAL; |
| break; |
| } |
| |
| pm_runtime_put(&client->dev); |
| |
| return ret; |
| } |
| |
| static const struct v4l2_ctrl_ops og01a1b_ctrl_ops = { |
| .s_ctrl = og01a1b_set_ctrl, |
| }; |
| |
| static int og01a1b_init_controls(struct og01a1b *og01a1b) |
| { |
| struct v4l2_ctrl_handler *ctrl_hdlr; |
| s64 exposure_max, h_blank; |
| int ret; |
| |
| ctrl_hdlr = &og01a1b->ctrl_handler; |
| ret = v4l2_ctrl_handler_init(ctrl_hdlr, 8); |
| if (ret) |
| return ret; |
| |
| ctrl_hdlr->lock = &og01a1b->mutex; |
| og01a1b->link_freq = v4l2_ctrl_new_int_menu(ctrl_hdlr, |
| &og01a1b_ctrl_ops, |
| V4L2_CID_LINK_FREQ, |
| ARRAY_SIZE |
| (link_freq_menu_items) - 1, |
| 0, link_freq_menu_items); |
| if (og01a1b->link_freq) |
| og01a1b->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY; |
| |
| og01a1b->pixel_rate = v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, |
| V4L2_CID_PIXEL_RATE, 0, |
| to_pixel_rate |
| (OG01A1B_LINK_FREQ_1000MBPS), |
| 1, |
| to_pixel_rate |
| (OG01A1B_LINK_FREQ_1000MBPS)); |
| og01a1b->vblank = v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, |
| V4L2_CID_VBLANK, |
| og01a1b->cur_mode->vts_min - |
| og01a1b->cur_mode->height, |
| OG01A1B_VTS_MAX - |
| og01a1b->cur_mode->height, 1, |
| og01a1b->cur_mode->vts_def - |
| og01a1b->cur_mode->height); |
| h_blank = to_pixels_per_line(og01a1b->cur_mode->hts, |
| og01a1b->cur_mode->link_freq_index) - |
| og01a1b->cur_mode->width; |
| og01a1b->hblank = v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, |
| V4L2_CID_HBLANK, h_blank, h_blank, |
| 1, h_blank); |
| if (og01a1b->hblank) |
| og01a1b->hblank->flags |= V4L2_CTRL_FLAG_READ_ONLY; |
| |
| v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, V4L2_CID_ANALOGUE_GAIN, |
| OG01A1B_ANAL_GAIN_MIN, OG01A1B_ANAL_GAIN_MAX, |
| OG01A1B_ANAL_GAIN_STEP, OG01A1B_ANAL_GAIN_MIN); |
| v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, V4L2_CID_DIGITAL_GAIN, |
| OG01A1B_DGTL_GAIN_MIN, OG01A1B_DGTL_GAIN_MAX, |
| OG01A1B_DGTL_GAIN_STEP, OG01A1B_DGTL_GAIN_DEFAULT); |
| exposure_max = (og01a1b->cur_mode->vts_def - |
| OG01A1B_EXPOSURE_MAX_MARGIN); |
| og01a1b->exposure = v4l2_ctrl_new_std(ctrl_hdlr, &og01a1b_ctrl_ops, |
| V4L2_CID_EXPOSURE, |
| OG01A1B_EXPOSURE_MIN, |
| exposure_max, |
| OG01A1B_EXPOSURE_STEP, |
| exposure_max); |
| v4l2_ctrl_new_std_menu_items(ctrl_hdlr, &og01a1b_ctrl_ops, |
| V4L2_CID_TEST_PATTERN, |
| ARRAY_SIZE(og01a1b_test_pattern_menu) - 1, |
| 0, 0, og01a1b_test_pattern_menu); |
| |
| if (ctrl_hdlr->error) |
| return ctrl_hdlr->error; |
| |
| og01a1b->sd.ctrl_handler = ctrl_hdlr; |
| |
| return 0; |
| } |
| |
| static void og01a1b_update_pad_format(const struct og01a1b_mode *mode, |
| struct v4l2_mbus_framefmt *fmt) |
| { |
| fmt->width = mode->width; |
| fmt->height = mode->height; |
| fmt->code = MEDIA_BUS_FMT_SGRBG10_1X10; |
| fmt->field = V4L2_FIELD_NONE; |
| } |
| |
| static int og01a1b_start_streaming(struct og01a1b *og01a1b) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| const struct og01a1b_reg_list *reg_list; |
| int link_freq_index, ret; |
| |
| link_freq_index = og01a1b->cur_mode->link_freq_index; |
| reg_list = &link_freq_configs[link_freq_index].reg_list; |
| |
| ret = og01a1b_write_reg_list(og01a1b, reg_list); |
| if (ret) { |
| dev_err(&client->dev, "failed to set plls"); |
| return ret; |
| } |
| |
| reg_list = &og01a1b->cur_mode->reg_list; |
| ret = og01a1b_write_reg_list(og01a1b, reg_list); |
| if (ret) { |
| dev_err(&client->dev, "failed to set mode"); |
| return ret; |
| } |
| |
| ret = __v4l2_ctrl_handler_setup(og01a1b->sd.ctrl_handler); |
| if (ret) |
| return ret; |
| |
| ret = og01a1b_write_reg(og01a1b, OG01A1B_REG_MODE_SELECT, |
| OG01A1B_REG_VALUE_08BIT, |
| OG01A1B_MODE_STREAMING); |
| if (ret) { |
| dev_err(&client->dev, "failed to set stream"); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void og01a1b_stop_streaming(struct og01a1b *og01a1b) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| |
| if (og01a1b_write_reg(og01a1b, OG01A1B_REG_MODE_SELECT, |
| OG01A1B_REG_VALUE_08BIT, OG01A1B_MODE_STANDBY)) |
| dev_err(&client->dev, "failed to set stream"); |
| } |
| |
| static int og01a1b_set_stream(struct v4l2_subdev *sd, int enable) |
| { |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| struct i2c_client *client = v4l2_get_subdevdata(sd); |
| int ret = 0; |
| |
| if (og01a1b->streaming == enable) |
| return 0; |
| |
| mutex_lock(&og01a1b->mutex); |
| if (enable) { |
| ret = pm_runtime_get_sync(&client->dev); |
| if (ret < 0) { |
| pm_runtime_put_noidle(&client->dev); |
| mutex_unlock(&og01a1b->mutex); |
| return ret; |
| } |
| |
| ret = og01a1b_start_streaming(og01a1b); |
| if (ret) { |
| enable = 0; |
| og01a1b_stop_streaming(og01a1b); |
| pm_runtime_put(&client->dev); |
| } |
| } else { |
| og01a1b_stop_streaming(og01a1b); |
| pm_runtime_put(&client->dev); |
| } |
| |
| og01a1b->streaming = enable; |
| mutex_unlock(&og01a1b->mutex); |
| |
| return ret; |
| } |
| |
| static int __maybe_unused og01a1b_suspend(struct device *dev) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| |
| mutex_lock(&og01a1b->mutex); |
| if (og01a1b->streaming) |
| og01a1b_stop_streaming(og01a1b); |
| |
| mutex_unlock(&og01a1b->mutex); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused og01a1b_resume(struct device *dev) |
| { |
| struct i2c_client *client = to_i2c_client(dev); |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| int ret; |
| |
| mutex_lock(&og01a1b->mutex); |
| if (og01a1b->streaming) { |
| ret = og01a1b_start_streaming(og01a1b); |
| if (ret) { |
| og01a1b->streaming = false; |
| og01a1b_stop_streaming(og01a1b); |
| mutex_unlock(&og01a1b->mutex); |
| return ret; |
| } |
| } |
| |
| mutex_unlock(&og01a1b->mutex); |
| |
| return 0; |
| } |
| |
| static int og01a1b_set_format(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *fmt) |
| { |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| const struct og01a1b_mode *mode; |
| s32 vblank_def, h_blank; |
| |
| mode = v4l2_find_nearest_size(supported_modes, |
| ARRAY_SIZE(supported_modes), width, |
| height, fmt->format.width, |
| fmt->format.height); |
| |
| mutex_lock(&og01a1b->mutex); |
| og01a1b_update_pad_format(mode, &fmt->format); |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { |
| *v4l2_subdev_get_try_format(sd, sd_state, |
| fmt->pad) = fmt->format; |
| } else { |
| og01a1b->cur_mode = mode; |
| __v4l2_ctrl_s_ctrl(og01a1b->link_freq, mode->link_freq_index); |
| __v4l2_ctrl_s_ctrl_int64(og01a1b->pixel_rate, |
| to_pixel_rate(mode->link_freq_index)); |
| |
| /* Update limits and set FPS to default */ |
| vblank_def = mode->vts_def - mode->height; |
| __v4l2_ctrl_modify_range(og01a1b->vblank, |
| mode->vts_min - mode->height, |
| OG01A1B_VTS_MAX - mode->height, 1, |
| vblank_def); |
| __v4l2_ctrl_s_ctrl(og01a1b->vblank, vblank_def); |
| h_blank = to_pixels_per_line(mode->hts, mode->link_freq_index) - |
| mode->width; |
| __v4l2_ctrl_modify_range(og01a1b->hblank, h_blank, h_blank, 1, |
| h_blank); |
| } |
| |
| mutex_unlock(&og01a1b->mutex); |
| |
| return 0; |
| } |
| |
| static int og01a1b_get_format(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *fmt) |
| { |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| |
| mutex_lock(&og01a1b->mutex); |
| if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) |
| fmt->format = *v4l2_subdev_get_try_format(&og01a1b->sd, |
| sd_state, |
| fmt->pad); |
| else |
| og01a1b_update_pad_format(og01a1b->cur_mode, &fmt->format); |
| |
| mutex_unlock(&og01a1b->mutex); |
| |
| return 0; |
| } |
| |
| static int og01a1b_enum_mbus_code(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_mbus_code_enum *code) |
| { |
| if (code->index > 0) |
| return -EINVAL; |
| |
| code->code = MEDIA_BUS_FMT_SGRBG10_1X10; |
| |
| return 0; |
| } |
| |
| static int og01a1b_enum_frame_size(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_frame_size_enum *fse) |
| { |
| if (fse->index >= ARRAY_SIZE(supported_modes)) |
| return -EINVAL; |
| |
| if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10) |
| return -EINVAL; |
| |
| fse->min_width = supported_modes[fse->index].width; |
| fse->max_width = fse->min_width; |
| fse->min_height = supported_modes[fse->index].height; |
| fse->max_height = fse->min_height; |
| |
| return 0; |
| } |
| |
| static int og01a1b_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) |
| { |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| |
| mutex_lock(&og01a1b->mutex); |
| og01a1b_update_pad_format(&supported_modes[0], |
| v4l2_subdev_get_try_format(sd, fh->state, 0)); |
| mutex_unlock(&og01a1b->mutex); |
| |
| return 0; |
| } |
| |
| static const struct v4l2_subdev_video_ops og01a1b_video_ops = { |
| .s_stream = og01a1b_set_stream, |
| }; |
| |
| static const struct v4l2_subdev_pad_ops og01a1b_pad_ops = { |
| .set_fmt = og01a1b_set_format, |
| .get_fmt = og01a1b_get_format, |
| .enum_mbus_code = og01a1b_enum_mbus_code, |
| .enum_frame_size = og01a1b_enum_frame_size, |
| }; |
| |
| static const struct v4l2_subdev_ops og01a1b_subdev_ops = { |
| .video = &og01a1b_video_ops, |
| .pad = &og01a1b_pad_ops, |
| }; |
| |
| static const struct media_entity_operations og01a1b_subdev_entity_ops = { |
| .link_validate = v4l2_subdev_link_validate, |
| }; |
| |
| static const struct v4l2_subdev_internal_ops og01a1b_internal_ops = { |
| .open = og01a1b_open, |
| }; |
| |
| static int og01a1b_identify_module(struct og01a1b *og01a1b) |
| { |
| struct i2c_client *client = v4l2_get_subdevdata(&og01a1b->sd); |
| int ret; |
| u32 val; |
| |
| ret = og01a1b_read_reg(og01a1b, OG01A1B_REG_CHIP_ID, |
| OG01A1B_REG_VALUE_24BIT, &val); |
| if (ret) |
| return ret; |
| |
| if (val != OG01A1B_CHIP_ID) { |
| dev_err(&client->dev, "chip id mismatch: %x!=%x", |
| OG01A1B_CHIP_ID, val); |
| return -ENXIO; |
| } |
| |
| return 0; |
| } |
| |
| static int og01a1b_check_hwcfg(struct device *dev) |
| { |
| struct fwnode_handle *ep; |
| struct fwnode_handle *fwnode = dev_fwnode(dev); |
| struct v4l2_fwnode_endpoint bus_cfg = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY |
| }; |
| u32 mclk; |
| int ret; |
| unsigned int i, j; |
| |
| if (!fwnode) |
| return -ENXIO; |
| |
| ret = fwnode_property_read_u32(fwnode, "clock-frequency", &mclk); |
| |
| if (ret) { |
| dev_err(dev, "can't get clock frequency"); |
| return ret; |
| } |
| |
| if (mclk != OG01A1B_MCLK) { |
| dev_err(dev, "external clock %d is not supported", mclk); |
| return -EINVAL; |
| } |
| |
| ep = fwnode_graph_get_next_endpoint(fwnode, NULL); |
| if (!ep) |
| return -ENXIO; |
| |
| ret = v4l2_fwnode_endpoint_alloc_parse(ep, &bus_cfg); |
| fwnode_handle_put(ep); |
| if (ret) |
| return ret; |
| |
| if (bus_cfg.bus.mipi_csi2.num_data_lanes != OG01A1B_DATA_LANES) { |
| dev_err(dev, "number of CSI2 data lanes %d is not supported", |
| bus_cfg.bus.mipi_csi2.num_data_lanes); |
| ret = -EINVAL; |
| goto check_hwcfg_error; |
| } |
| |
| if (!bus_cfg.nr_of_link_frequencies) { |
| dev_err(dev, "no link frequencies defined"); |
| ret = -EINVAL; |
| goto check_hwcfg_error; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(link_freq_menu_items); i++) { |
| for (j = 0; j < bus_cfg.nr_of_link_frequencies; j++) { |
| if (link_freq_menu_items[i] == |
| bus_cfg.link_frequencies[j]) |
| break; |
| } |
| |
| if (j == bus_cfg.nr_of_link_frequencies) { |
| dev_err(dev, "no link frequency %lld supported", |
| link_freq_menu_items[i]); |
| ret = -EINVAL; |
| goto check_hwcfg_error; |
| } |
| } |
| |
| check_hwcfg_error: |
| v4l2_fwnode_endpoint_free(&bus_cfg); |
| |
| return ret; |
| } |
| |
| static void og01a1b_remove(struct i2c_client *client) |
| { |
| struct v4l2_subdev *sd = i2c_get_clientdata(client); |
| struct og01a1b *og01a1b = to_og01a1b(sd); |
| |
| v4l2_async_unregister_subdev(sd); |
| media_entity_cleanup(&sd->entity); |
| v4l2_ctrl_handler_free(sd->ctrl_handler); |
| pm_runtime_disable(&client->dev); |
| mutex_destroy(&og01a1b->mutex); |
| } |
| |
| static int og01a1b_probe(struct i2c_client *client) |
| { |
| struct og01a1b *og01a1b; |
| int ret; |
| |
| ret = og01a1b_check_hwcfg(&client->dev); |
| if (ret) { |
| dev_err(&client->dev, "failed to check HW configuration: %d", |
| ret); |
| return ret; |
| } |
| |
| og01a1b = devm_kzalloc(&client->dev, sizeof(*og01a1b), GFP_KERNEL); |
| if (!og01a1b) |
| return -ENOMEM; |
| |
| v4l2_i2c_subdev_init(&og01a1b->sd, client, &og01a1b_subdev_ops); |
| ret = og01a1b_identify_module(og01a1b); |
| if (ret) { |
| dev_err(&client->dev, "failed to find sensor: %d", ret); |
| return ret; |
| } |
| |
| mutex_init(&og01a1b->mutex); |
| og01a1b->cur_mode = &supported_modes[0]; |
| ret = og01a1b_init_controls(og01a1b); |
| if (ret) { |
| dev_err(&client->dev, "failed to init controls: %d", ret); |
| goto probe_error_v4l2_ctrl_handler_free; |
| } |
| |
| og01a1b->sd.internal_ops = &og01a1b_internal_ops; |
| og01a1b->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; |
| og01a1b->sd.entity.ops = &og01a1b_subdev_entity_ops; |
| og01a1b->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR; |
| og01a1b->pad.flags = MEDIA_PAD_FL_SOURCE; |
| ret = media_entity_pads_init(&og01a1b->sd.entity, 1, &og01a1b->pad); |
| if (ret) { |
| dev_err(&client->dev, "failed to init entity pads: %d", ret); |
| goto probe_error_v4l2_ctrl_handler_free; |
| } |
| |
| ret = v4l2_async_register_subdev_sensor(&og01a1b->sd); |
| if (ret < 0) { |
| dev_err(&client->dev, "failed to register V4L2 subdev: %d", |
| ret); |
| goto probe_error_media_entity_cleanup; |
| } |
| |
| /* |
| * Device is already turned on by i2c-core with ACPI domain PM. |
| * Enable runtime PM and turn off the device. |
| */ |
| pm_runtime_set_active(&client->dev); |
| pm_runtime_enable(&client->dev); |
| pm_runtime_idle(&client->dev); |
| |
| return 0; |
| |
| probe_error_media_entity_cleanup: |
| media_entity_cleanup(&og01a1b->sd.entity); |
| |
| probe_error_v4l2_ctrl_handler_free: |
| v4l2_ctrl_handler_free(og01a1b->sd.ctrl_handler); |
| mutex_destroy(&og01a1b->mutex); |
| |
| return ret; |
| } |
| |
| static const struct dev_pm_ops og01a1b_pm_ops = { |
| SET_SYSTEM_SLEEP_PM_OPS(og01a1b_suspend, og01a1b_resume) |
| }; |
| |
| #ifdef CONFIG_ACPI |
| static const struct acpi_device_id og01a1b_acpi_ids[] = { |
| {"OVTI01AC"}, |
| {} |
| }; |
| |
| MODULE_DEVICE_TABLE(acpi, og01a1b_acpi_ids); |
| #endif |
| |
| static struct i2c_driver og01a1b_i2c_driver = { |
| .driver = { |
| .name = "og01a1b", |
| .pm = &og01a1b_pm_ops, |
| .acpi_match_table = ACPI_PTR(og01a1b_acpi_ids), |
| }, |
| .probe_new = og01a1b_probe, |
| .remove = og01a1b_remove, |
| }; |
| |
| module_i2c_driver(og01a1b_i2c_driver); |
| |
| MODULE_AUTHOR("Shawn Tu <shawnx.tu@intel.com>"); |
| MODULE_DESCRIPTION("OmniVision OG01A1B sensor driver"); |
| MODULE_LICENSE("GPL v2"); |