| /* |
| * Renesas R-Car SATA driver |
| * |
| * Author: Vladimir Barinov <source@cogentembedded.com> |
| * Copyright (C) 2013 Cogent Embedded, Inc. |
| * Copyright (C) 2013 Renesas Solutions Corp. |
| * |
| * This program is free software; you can redistribute it and/or modify it |
| * under the terms of the GNU General Public License as published by the |
| * Free Software Foundation; either version 2 of the License, or (at your |
| * option) any later version. |
| */ |
| |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/ata.h> |
| #include <linux/libata.h> |
| #include <linux/of_device.h> |
| #include <linux/platform_device.h> |
| #include <linux/clk.h> |
| #include <linux/err.h> |
| |
| #define DRV_NAME "sata_rcar" |
| |
| /* SH-Navi2G/ATAPI-ATA compatible task registers */ |
| #define DATA_REG 0x100 |
| #define SDEVCON_REG 0x138 |
| |
| /* SH-Navi2G/ATAPI module compatible control registers */ |
| #define ATAPI_CONTROL1_REG 0x180 |
| #define ATAPI_STATUS_REG 0x184 |
| #define ATAPI_INT_ENABLE_REG 0x188 |
| #define ATAPI_DTB_ADR_REG 0x198 |
| #define ATAPI_DMA_START_ADR_REG 0x19C |
| #define ATAPI_DMA_TRANS_CNT_REG 0x1A0 |
| #define ATAPI_CONTROL2_REG 0x1A4 |
| #define ATAPI_SIG_ST_REG 0x1B0 |
| #define ATAPI_BYTE_SWAP_REG 0x1BC |
| |
| /* ATAPI control 1 register (ATAPI_CONTROL1) bits */ |
| #define ATAPI_CONTROL1_ISM BIT(16) |
| #define ATAPI_CONTROL1_DTA32M BIT(11) |
| #define ATAPI_CONTROL1_RESET BIT(7) |
| #define ATAPI_CONTROL1_DESE BIT(3) |
| #define ATAPI_CONTROL1_RW BIT(2) |
| #define ATAPI_CONTROL1_STOP BIT(1) |
| #define ATAPI_CONTROL1_START BIT(0) |
| |
| /* ATAPI status register (ATAPI_STATUS) bits */ |
| #define ATAPI_STATUS_SATAINT BIT(11) |
| #define ATAPI_STATUS_DNEND BIT(6) |
| #define ATAPI_STATUS_DEVTRM BIT(5) |
| #define ATAPI_STATUS_DEVINT BIT(4) |
| #define ATAPI_STATUS_ERR BIT(2) |
| #define ATAPI_STATUS_NEND BIT(1) |
| #define ATAPI_STATUS_ACT BIT(0) |
| |
| /* Interrupt enable register (ATAPI_INT_ENABLE) bits */ |
| #define ATAPI_INT_ENABLE_SATAINT BIT(11) |
| #define ATAPI_INT_ENABLE_DNEND BIT(6) |
| #define ATAPI_INT_ENABLE_DEVTRM BIT(5) |
| #define ATAPI_INT_ENABLE_DEVINT BIT(4) |
| #define ATAPI_INT_ENABLE_ERR BIT(2) |
| #define ATAPI_INT_ENABLE_NEND BIT(1) |
| #define ATAPI_INT_ENABLE_ACT BIT(0) |
| |
| /* Access control registers for physical layer control register */ |
| #define SATAPHYADDR_REG 0x200 |
| #define SATAPHYWDATA_REG 0x204 |
| #define SATAPHYACCEN_REG 0x208 |
| #define SATAPHYRESET_REG 0x20C |
| #define SATAPHYRDATA_REG 0x210 |
| #define SATAPHYACK_REG 0x214 |
| |
| /* Physical layer control address command register (SATAPHYADDR) bits */ |
| #define SATAPHYADDR_PHYRATEMODE BIT(10) |
| #define SATAPHYADDR_PHYCMD_READ BIT(9) |
| #define SATAPHYADDR_PHYCMD_WRITE BIT(8) |
| |
| /* Physical layer control enable register (SATAPHYACCEN) bits */ |
| #define SATAPHYACCEN_PHYLANE BIT(0) |
| |
| /* Physical layer control reset register (SATAPHYRESET) bits */ |
| #define SATAPHYRESET_PHYRST BIT(1) |
| #define SATAPHYRESET_PHYSRES BIT(0) |
| |
| /* Physical layer control acknowledge register (SATAPHYACK) bits */ |
| #define SATAPHYACK_PHYACK BIT(0) |
| |
| /* Serial-ATA HOST control registers */ |
| #define BISTCONF_REG 0x102C |
| #define SDATA_REG 0x1100 |
| #define SSDEVCON_REG 0x1204 |
| |
| #define SCRSSTS_REG 0x1400 |
| #define SCRSERR_REG 0x1404 |
| #define SCRSCON_REG 0x1408 |
| #define SCRSACT_REG 0x140C |
| |
| #define SATAINTSTAT_REG 0x1508 |
| #define SATAINTMASK_REG 0x150C |
| |
| /* SATA INT status register (SATAINTSTAT) bits */ |
| #define SATAINTSTAT_SERR BIT(3) |
| #define SATAINTSTAT_ATA BIT(0) |
| |
| /* SATA INT mask register (SATAINTSTAT) bits */ |
| #define SATAINTMASK_SERRMSK BIT(3) |
| #define SATAINTMASK_ERRMSK BIT(2) |
| #define SATAINTMASK_ERRCRTMSK BIT(1) |
| #define SATAINTMASK_ATAMSK BIT(0) |
| |
| #define SATA_RCAR_INT_MASK (SATAINTMASK_SERRMSK | \ |
| SATAINTMASK_ATAMSK) |
| |
| /* Physical Layer Control Registers */ |
| #define SATAPCTLR1_REG 0x43 |
| #define SATAPCTLR2_REG 0x52 |
| #define SATAPCTLR3_REG 0x5A |
| #define SATAPCTLR4_REG 0x60 |
| |
| /* Descriptor table word 0 bit (when DTA32M = 1) */ |
| #define SATA_RCAR_DTEND BIT(0) |
| |
| #define SATA_RCAR_DMA_BOUNDARY 0x1FFFFFFEUL |
| |
| /* Gen2 Physical Layer Control Registers */ |
| #define RCAR_GEN2_PHY_CTL1_REG 0x1704 |
| #define RCAR_GEN2_PHY_CTL1 0x34180002 |
| #define RCAR_GEN2_PHY_CTL1_SS 0xC180 /* Spread Spectrum */ |
| |
| #define RCAR_GEN2_PHY_CTL2_REG 0x170C |
| #define RCAR_GEN2_PHY_CTL2 0x00002303 |
| |
| #define RCAR_GEN2_PHY_CTL3_REG 0x171C |
| #define RCAR_GEN2_PHY_CTL3 0x000B0194 |
| |
| #define RCAR_GEN2_PHY_CTL4_REG 0x1724 |
| #define RCAR_GEN2_PHY_CTL4 0x00030994 |
| |
| #define RCAR_GEN2_PHY_CTL5_REG 0x1740 |
| #define RCAR_GEN2_PHY_CTL5 0x03004001 |
| #define RCAR_GEN2_PHY_CTL5_DC BIT(1) /* DC connection */ |
| #define RCAR_GEN2_PHY_CTL5_TR BIT(2) /* Termination Resistor */ |
| |
| enum sata_rcar_type { |
| RCAR_GEN1_SATA, |
| RCAR_GEN2_SATA, |
| RCAR_R8A7790_ES1_SATA, |
| }; |
| |
| struct sata_rcar_priv { |
| void __iomem *base; |
| struct clk *clk; |
| enum sata_rcar_type type; |
| }; |
| |
| static void sata_rcar_gen1_phy_preinit(struct sata_rcar_priv *priv) |
| { |
| void __iomem *base = priv->base; |
| |
| /* idle state */ |
| iowrite32(0, base + SATAPHYADDR_REG); |
| /* reset */ |
| iowrite32(SATAPHYRESET_PHYRST, base + SATAPHYRESET_REG); |
| udelay(10); |
| /* deassert reset */ |
| iowrite32(0, base + SATAPHYRESET_REG); |
| } |
| |
| static void sata_rcar_gen1_phy_write(struct sata_rcar_priv *priv, u16 reg, |
| u32 val, int group) |
| { |
| void __iomem *base = priv->base; |
| int timeout; |
| |
| /* deassert reset */ |
| iowrite32(0, base + SATAPHYRESET_REG); |
| /* lane 1 */ |
| iowrite32(SATAPHYACCEN_PHYLANE, base + SATAPHYACCEN_REG); |
| /* write phy register value */ |
| iowrite32(val, base + SATAPHYWDATA_REG); |
| /* set register group */ |
| if (group) |
| reg |= SATAPHYADDR_PHYRATEMODE; |
| /* write command */ |
| iowrite32(SATAPHYADDR_PHYCMD_WRITE | reg, base + SATAPHYADDR_REG); |
| /* wait for ack */ |
| for (timeout = 0; timeout < 100; timeout++) { |
| val = ioread32(base + SATAPHYACK_REG); |
| if (val & SATAPHYACK_PHYACK) |
| break; |
| } |
| if (timeout >= 100) |
| pr_err("%s timeout\n", __func__); |
| /* idle state */ |
| iowrite32(0, base + SATAPHYADDR_REG); |
| } |
| |
| static void sata_rcar_gen1_phy_init(struct sata_rcar_priv *priv) |
| { |
| sata_rcar_gen1_phy_preinit(priv); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 0); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR1_REG, 0x00200188, 1); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR3_REG, 0x0000A061, 0); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 0); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR2_REG, 0x20000000, 1); |
| sata_rcar_gen1_phy_write(priv, SATAPCTLR4_REG, 0x28E80000, 0); |
| } |
| |
| static void sata_rcar_gen2_phy_init(struct sata_rcar_priv *priv) |
| { |
| void __iomem *base = priv->base; |
| |
| iowrite32(RCAR_GEN2_PHY_CTL1, base + RCAR_GEN2_PHY_CTL1_REG); |
| iowrite32(RCAR_GEN2_PHY_CTL2, base + RCAR_GEN2_PHY_CTL2_REG); |
| iowrite32(RCAR_GEN2_PHY_CTL3, base + RCAR_GEN2_PHY_CTL3_REG); |
| iowrite32(RCAR_GEN2_PHY_CTL4, base + RCAR_GEN2_PHY_CTL4_REG); |
| iowrite32(RCAR_GEN2_PHY_CTL5 | RCAR_GEN2_PHY_CTL5_DC | |
| RCAR_GEN2_PHY_CTL5_TR, base + RCAR_GEN2_PHY_CTL5_REG); |
| } |
| |
| static void sata_rcar_freeze(struct ata_port *ap) |
| { |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| |
| /* mask */ |
| iowrite32(0x7ff, priv->base + SATAINTMASK_REG); |
| |
| ata_sff_freeze(ap); |
| } |
| |
| static void sata_rcar_thaw(struct ata_port *ap) |
| { |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| void __iomem *base = priv->base; |
| |
| /* ack */ |
| iowrite32(~(u32)SATA_RCAR_INT_MASK, base + SATAINTSTAT_REG); |
| |
| ata_sff_thaw(ap); |
| |
| /* unmask */ |
| iowrite32(0x7ff & ~SATA_RCAR_INT_MASK, base + SATAINTMASK_REG); |
| } |
| |
| static void sata_rcar_ioread16_rep(void __iomem *reg, void *buffer, int count) |
| { |
| u16 *ptr = buffer; |
| |
| while (count--) { |
| u16 data = ioread32(reg); |
| |
| *ptr++ = data; |
| } |
| } |
| |
| static void sata_rcar_iowrite16_rep(void __iomem *reg, void *buffer, int count) |
| { |
| const u16 *ptr = buffer; |
| |
| while (count--) |
| iowrite32(*ptr++, reg); |
| } |
| |
| static u8 sata_rcar_check_status(struct ata_port *ap) |
| { |
| return ioread32(ap->ioaddr.status_addr); |
| } |
| |
| static u8 sata_rcar_check_altstatus(struct ata_port *ap) |
| { |
| return ioread32(ap->ioaddr.altstatus_addr); |
| } |
| |
| static void sata_rcar_set_devctl(struct ata_port *ap, u8 ctl) |
| { |
| iowrite32(ctl, ap->ioaddr.ctl_addr); |
| } |
| |
| static void sata_rcar_dev_select(struct ata_port *ap, unsigned int device) |
| { |
| iowrite32(ATA_DEVICE_OBS, ap->ioaddr.device_addr); |
| ata_sff_pause(ap); /* needed; also flushes, for mmio */ |
| } |
| |
| static unsigned int sata_rcar_ata_devchk(struct ata_port *ap, |
| unsigned int device) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| u8 nsect, lbal; |
| |
| sata_rcar_dev_select(ap, device); |
| |
| iowrite32(0x55, ioaddr->nsect_addr); |
| iowrite32(0xaa, ioaddr->lbal_addr); |
| |
| iowrite32(0xaa, ioaddr->nsect_addr); |
| iowrite32(0x55, ioaddr->lbal_addr); |
| |
| iowrite32(0x55, ioaddr->nsect_addr); |
| iowrite32(0xaa, ioaddr->lbal_addr); |
| |
| nsect = ioread32(ioaddr->nsect_addr); |
| lbal = ioread32(ioaddr->lbal_addr); |
| |
| if (nsect == 0x55 && lbal == 0xaa) |
| return 1; /* found a device */ |
| |
| return 0; /* nothing found */ |
| } |
| |
| static int sata_rcar_wait_after_reset(struct ata_link *link, |
| unsigned long deadline) |
| { |
| struct ata_port *ap = link->ap; |
| |
| ata_msleep(ap, ATA_WAIT_AFTER_RESET); |
| |
| return ata_sff_wait_ready(link, deadline); |
| } |
| |
| static int sata_rcar_bus_softreset(struct ata_port *ap, unsigned long deadline) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| |
| DPRINTK("ata%u: bus reset via SRST\n", ap->print_id); |
| |
| /* software reset. causes dev0 to be selected */ |
| iowrite32(ap->ctl, ioaddr->ctl_addr); |
| udelay(20); |
| iowrite32(ap->ctl | ATA_SRST, ioaddr->ctl_addr); |
| udelay(20); |
| iowrite32(ap->ctl, ioaddr->ctl_addr); |
| ap->last_ctl = ap->ctl; |
| |
| /* wait the port to become ready */ |
| return sata_rcar_wait_after_reset(&ap->link, deadline); |
| } |
| |
| static int sata_rcar_softreset(struct ata_link *link, unsigned int *classes, |
| unsigned long deadline) |
| { |
| struct ata_port *ap = link->ap; |
| unsigned int devmask = 0; |
| int rc; |
| u8 err; |
| |
| /* determine if device 0 is present */ |
| if (sata_rcar_ata_devchk(ap, 0)) |
| devmask |= 1 << 0; |
| |
| /* issue bus reset */ |
| DPRINTK("about to softreset, devmask=%x\n", devmask); |
| rc = sata_rcar_bus_softreset(ap, deadline); |
| /* if link is occupied, -ENODEV too is an error */ |
| if (rc && (rc != -ENODEV || sata_scr_valid(link))) { |
| ata_link_err(link, "SRST failed (errno=%d)\n", rc); |
| return rc; |
| } |
| |
| /* determine by signature whether we have ATA or ATAPI devices */ |
| classes[0] = ata_sff_dev_classify(&link->device[0], devmask, &err); |
| |
| DPRINTK("classes[0]=%u\n", classes[0]); |
| return 0; |
| } |
| |
| static void sata_rcar_tf_load(struct ata_port *ap, |
| const struct ata_taskfile *tf) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR; |
| |
| if (tf->ctl != ap->last_ctl) { |
| iowrite32(tf->ctl, ioaddr->ctl_addr); |
| ap->last_ctl = tf->ctl; |
| ata_wait_idle(ap); |
| } |
| |
| if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) { |
| iowrite32(tf->hob_feature, ioaddr->feature_addr); |
| iowrite32(tf->hob_nsect, ioaddr->nsect_addr); |
| iowrite32(tf->hob_lbal, ioaddr->lbal_addr); |
| iowrite32(tf->hob_lbam, ioaddr->lbam_addr); |
| iowrite32(tf->hob_lbah, ioaddr->lbah_addr); |
| VPRINTK("hob: feat 0x%X nsect 0x%X, lba 0x%X 0x%X 0x%X\n", |
| tf->hob_feature, |
| tf->hob_nsect, |
| tf->hob_lbal, |
| tf->hob_lbam, |
| tf->hob_lbah); |
| } |
| |
| if (is_addr) { |
| iowrite32(tf->feature, ioaddr->feature_addr); |
| iowrite32(tf->nsect, ioaddr->nsect_addr); |
| iowrite32(tf->lbal, ioaddr->lbal_addr); |
| iowrite32(tf->lbam, ioaddr->lbam_addr); |
| iowrite32(tf->lbah, ioaddr->lbah_addr); |
| VPRINTK("feat 0x%X nsect 0x%X lba 0x%X 0x%X 0x%X\n", |
| tf->feature, |
| tf->nsect, |
| tf->lbal, |
| tf->lbam, |
| tf->lbah); |
| } |
| |
| if (tf->flags & ATA_TFLAG_DEVICE) { |
| iowrite32(tf->device, ioaddr->device_addr); |
| VPRINTK("device 0x%X\n", tf->device); |
| } |
| |
| ata_wait_idle(ap); |
| } |
| |
| static void sata_rcar_tf_read(struct ata_port *ap, struct ata_taskfile *tf) |
| { |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| |
| tf->command = sata_rcar_check_status(ap); |
| tf->feature = ioread32(ioaddr->error_addr); |
| tf->nsect = ioread32(ioaddr->nsect_addr); |
| tf->lbal = ioread32(ioaddr->lbal_addr); |
| tf->lbam = ioread32(ioaddr->lbam_addr); |
| tf->lbah = ioread32(ioaddr->lbah_addr); |
| tf->device = ioread32(ioaddr->device_addr); |
| |
| if (tf->flags & ATA_TFLAG_LBA48) { |
| iowrite32(tf->ctl | ATA_HOB, ioaddr->ctl_addr); |
| tf->hob_feature = ioread32(ioaddr->error_addr); |
| tf->hob_nsect = ioread32(ioaddr->nsect_addr); |
| tf->hob_lbal = ioread32(ioaddr->lbal_addr); |
| tf->hob_lbam = ioread32(ioaddr->lbam_addr); |
| tf->hob_lbah = ioread32(ioaddr->lbah_addr); |
| iowrite32(tf->ctl, ioaddr->ctl_addr); |
| ap->last_ctl = tf->ctl; |
| } |
| } |
| |
| static void sata_rcar_exec_command(struct ata_port *ap, |
| const struct ata_taskfile *tf) |
| { |
| DPRINTK("ata%u: cmd 0x%X\n", ap->print_id, tf->command); |
| |
| iowrite32(tf->command, ap->ioaddr.command_addr); |
| ata_sff_pause(ap); |
| } |
| |
| static unsigned int sata_rcar_data_xfer(struct ata_device *dev, |
| unsigned char *buf, |
| unsigned int buflen, int rw) |
| { |
| struct ata_port *ap = dev->link->ap; |
| void __iomem *data_addr = ap->ioaddr.data_addr; |
| unsigned int words = buflen >> 1; |
| |
| /* Transfer multiple of 2 bytes */ |
| if (rw == READ) |
| sata_rcar_ioread16_rep(data_addr, buf, words); |
| else |
| sata_rcar_iowrite16_rep(data_addr, buf, words); |
| |
| /* Transfer trailing byte, if any. */ |
| if (unlikely(buflen & 0x01)) { |
| unsigned char pad[2] = { }; |
| |
| /* Point buf to the tail of buffer */ |
| buf += buflen - 1; |
| |
| /* |
| * Use io*16_rep() accessors here as well to avoid pointlessly |
| * swapping bytes to and from on the big endian machines... |
| */ |
| if (rw == READ) { |
| sata_rcar_ioread16_rep(data_addr, pad, 1); |
| *buf = pad[0]; |
| } else { |
| pad[0] = *buf; |
| sata_rcar_iowrite16_rep(data_addr, pad, 1); |
| } |
| words++; |
| } |
| |
| return words << 1; |
| } |
| |
| static void sata_rcar_drain_fifo(struct ata_queued_cmd *qc) |
| { |
| int count; |
| struct ata_port *ap; |
| |
| /* We only need to flush incoming data when a command was running */ |
| if (qc == NULL || qc->dma_dir == DMA_TO_DEVICE) |
| return; |
| |
| ap = qc->ap; |
| /* Drain up to 64K of data before we give up this recovery method */ |
| for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ) && |
| count < 65536; count += 2) |
| ioread32(ap->ioaddr.data_addr); |
| |
| /* Can become DEBUG later */ |
| if (count) |
| ata_port_dbg(ap, "drained %d bytes to clear DRQ\n", count); |
| } |
| |
| static int sata_rcar_scr_read(struct ata_link *link, unsigned int sc_reg, |
| u32 *val) |
| { |
| if (sc_reg > SCR_ACTIVE) |
| return -EINVAL; |
| |
| *val = ioread32(link->ap->ioaddr.scr_addr + (sc_reg << 2)); |
| return 0; |
| } |
| |
| static int sata_rcar_scr_write(struct ata_link *link, unsigned int sc_reg, |
| u32 val) |
| { |
| if (sc_reg > SCR_ACTIVE) |
| return -EINVAL; |
| |
| iowrite32(val, link->ap->ioaddr.scr_addr + (sc_reg << 2)); |
| return 0; |
| } |
| |
| static void sata_rcar_bmdma_fill_sg(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct ata_bmdma_prd *prd = ap->bmdma_prd; |
| struct scatterlist *sg; |
| unsigned int si; |
| |
| for_each_sg(qc->sg, sg, qc->n_elem, si) { |
| u32 addr, sg_len; |
| |
| /* |
| * Note: h/w doesn't support 64-bit, so we unconditionally |
| * truncate dma_addr_t to u32. |
| */ |
| addr = (u32)sg_dma_address(sg); |
| sg_len = sg_dma_len(sg); |
| |
| prd[si].addr = cpu_to_le32(addr); |
| prd[si].flags_len = cpu_to_le32(sg_len); |
| VPRINTK("PRD[%u] = (0x%X, 0x%X)\n", si, addr, sg_len); |
| } |
| |
| /* end-of-table flag */ |
| prd[si - 1].addr |= cpu_to_le32(SATA_RCAR_DTEND); |
| } |
| |
| static void sata_rcar_qc_prep(struct ata_queued_cmd *qc) |
| { |
| if (!(qc->flags & ATA_QCFLAG_DMAMAP)) |
| return; |
| |
| sata_rcar_bmdma_fill_sg(qc); |
| } |
| |
| static void sata_rcar_bmdma_setup(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| unsigned int rw = qc->tf.flags & ATA_TFLAG_WRITE; |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| void __iomem *base = priv->base; |
| u32 dmactl; |
| |
| /* load PRD table addr. */ |
| mb(); /* make sure PRD table writes are visible to controller */ |
| iowrite32(ap->bmdma_prd_dma, base + ATAPI_DTB_ADR_REG); |
| |
| /* specify data direction, triple-check start bit is clear */ |
| dmactl = ioread32(base + ATAPI_CONTROL1_REG); |
| dmactl &= ~(ATAPI_CONTROL1_RW | ATAPI_CONTROL1_STOP); |
| if (dmactl & ATAPI_CONTROL1_START) { |
| dmactl &= ~ATAPI_CONTROL1_START; |
| dmactl |= ATAPI_CONTROL1_STOP; |
| } |
| if (!rw) |
| dmactl |= ATAPI_CONTROL1_RW; |
| iowrite32(dmactl, base + ATAPI_CONTROL1_REG); |
| |
| /* issue r/w command */ |
| ap->ops->sff_exec_command(ap, &qc->tf); |
| } |
| |
| static void sata_rcar_bmdma_start(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| void __iomem *base = priv->base; |
| u32 dmactl; |
| |
| /* start host DMA transaction */ |
| dmactl = ioread32(base + ATAPI_CONTROL1_REG); |
| dmactl &= ~ATAPI_CONTROL1_STOP; |
| dmactl |= ATAPI_CONTROL1_START; |
| iowrite32(dmactl, base + ATAPI_CONTROL1_REG); |
| } |
| |
| static void sata_rcar_bmdma_stop(struct ata_queued_cmd *qc) |
| { |
| struct ata_port *ap = qc->ap; |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| void __iomem *base = priv->base; |
| u32 dmactl; |
| |
| /* force termination of DMA transfer if active */ |
| dmactl = ioread32(base + ATAPI_CONTROL1_REG); |
| if (dmactl & ATAPI_CONTROL1_START) { |
| dmactl &= ~ATAPI_CONTROL1_START; |
| dmactl |= ATAPI_CONTROL1_STOP; |
| iowrite32(dmactl, base + ATAPI_CONTROL1_REG); |
| } |
| |
| /* one-PIO-cycle guaranteed wait, per spec, for HDMA1:0 transition */ |
| ata_sff_dma_pause(ap); |
| } |
| |
| static u8 sata_rcar_bmdma_status(struct ata_port *ap) |
| { |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| u8 host_stat = 0; |
| u32 status; |
| |
| status = ioread32(priv->base + ATAPI_STATUS_REG); |
| if (status & ATAPI_STATUS_DEVINT) |
| host_stat |= ATA_DMA_INTR; |
| if (status & ATAPI_STATUS_ACT) |
| host_stat |= ATA_DMA_ACTIVE; |
| |
| return host_stat; |
| } |
| |
| static struct scsi_host_template sata_rcar_sht = { |
| ATA_BASE_SHT(DRV_NAME), |
| /* |
| * This controller allows transfer chunks up to 512MB which cross 64KB |
| * boundaries, therefore the DMA limits are more relaxed than standard |
| * ATA SFF. |
| */ |
| .sg_tablesize = ATA_MAX_PRD, |
| .dma_boundary = SATA_RCAR_DMA_BOUNDARY, |
| }; |
| |
| static struct ata_port_operations sata_rcar_port_ops = { |
| .inherits = &ata_bmdma_port_ops, |
| |
| .freeze = sata_rcar_freeze, |
| .thaw = sata_rcar_thaw, |
| .softreset = sata_rcar_softreset, |
| |
| .scr_read = sata_rcar_scr_read, |
| .scr_write = sata_rcar_scr_write, |
| |
| .sff_dev_select = sata_rcar_dev_select, |
| .sff_set_devctl = sata_rcar_set_devctl, |
| .sff_check_status = sata_rcar_check_status, |
| .sff_check_altstatus = sata_rcar_check_altstatus, |
| .sff_tf_load = sata_rcar_tf_load, |
| .sff_tf_read = sata_rcar_tf_read, |
| .sff_exec_command = sata_rcar_exec_command, |
| .sff_data_xfer = sata_rcar_data_xfer, |
| .sff_drain_fifo = sata_rcar_drain_fifo, |
| |
| .qc_prep = sata_rcar_qc_prep, |
| |
| .bmdma_setup = sata_rcar_bmdma_setup, |
| .bmdma_start = sata_rcar_bmdma_start, |
| .bmdma_stop = sata_rcar_bmdma_stop, |
| .bmdma_status = sata_rcar_bmdma_status, |
| }; |
| |
| static void sata_rcar_serr_interrupt(struct ata_port *ap) |
| { |
| struct sata_rcar_priv *priv = ap->host->private_data; |
| struct ata_eh_info *ehi = &ap->link.eh_info; |
| int freeze = 0; |
| u32 serror; |
| |
| serror = ioread32(priv->base + SCRSERR_REG); |
| if (!serror) |
| return; |
| |
| DPRINTK("SError @host_intr: 0x%x\n", serror); |
| |
| /* first, analyze and record host port events */ |
| ata_ehi_clear_desc(ehi); |
| |
| if (serror & (SERR_DEV_XCHG | SERR_PHYRDY_CHG)) { |
| /* Setup a soft-reset EH action */ |
| ata_ehi_hotplugged(ehi); |
| ata_ehi_push_desc(ehi, "%s", "hotplug"); |
| |
| freeze = serror & SERR_COMM_WAKE ? 0 : 1; |
| } |
| |
| /* freeze or abort */ |
| if (freeze) |
| ata_port_freeze(ap); |
| else |
| ata_port_abort(ap); |
| } |
| |
| static void sata_rcar_ata_interrupt(struct ata_port *ap) |
| { |
| struct ata_queued_cmd *qc; |
| int handled = 0; |
| |
| qc = ata_qc_from_tag(ap, ap->link.active_tag); |
| if (qc) |
| handled |= ata_bmdma_port_intr(ap, qc); |
| |
| /* be sure to clear ATA interrupt */ |
| if (!handled) |
| sata_rcar_check_status(ap); |
| } |
| |
| static irqreturn_t sata_rcar_interrupt(int irq, void *dev_instance) |
| { |
| struct ata_host *host = dev_instance; |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| unsigned int handled = 0; |
| struct ata_port *ap; |
| u32 sataintstat; |
| unsigned long flags; |
| |
| spin_lock_irqsave(&host->lock, flags); |
| |
| sataintstat = ioread32(base + SATAINTSTAT_REG); |
| sataintstat &= SATA_RCAR_INT_MASK; |
| if (!sataintstat) |
| goto done; |
| /* ack */ |
| iowrite32(~sataintstat & 0x7ff, base + SATAINTSTAT_REG); |
| |
| ap = host->ports[0]; |
| |
| if (sataintstat & SATAINTSTAT_ATA) |
| sata_rcar_ata_interrupt(ap); |
| |
| if (sataintstat & SATAINTSTAT_SERR) |
| sata_rcar_serr_interrupt(ap); |
| |
| handled = 1; |
| done: |
| spin_unlock_irqrestore(&host->lock, flags); |
| |
| return IRQ_RETVAL(handled); |
| } |
| |
| static void sata_rcar_setup_port(struct ata_host *host) |
| { |
| struct ata_port *ap = host->ports[0]; |
| struct ata_ioports *ioaddr = &ap->ioaddr; |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| |
| ap->ops = &sata_rcar_port_ops; |
| ap->pio_mask = ATA_PIO4; |
| ap->udma_mask = ATA_UDMA6; |
| ap->flags |= ATA_FLAG_SATA; |
| |
| if (priv->type == RCAR_R8A7790_ES1_SATA) |
| ap->flags |= ATA_FLAG_NO_DIPM; |
| |
| ioaddr->cmd_addr = base + SDATA_REG; |
| ioaddr->ctl_addr = base + SSDEVCON_REG; |
| ioaddr->scr_addr = base + SCRSSTS_REG; |
| ioaddr->altstatus_addr = ioaddr->ctl_addr; |
| |
| ioaddr->data_addr = ioaddr->cmd_addr + (ATA_REG_DATA << 2); |
| ioaddr->error_addr = ioaddr->cmd_addr + (ATA_REG_ERR << 2); |
| ioaddr->feature_addr = ioaddr->cmd_addr + (ATA_REG_FEATURE << 2); |
| ioaddr->nsect_addr = ioaddr->cmd_addr + (ATA_REG_NSECT << 2); |
| ioaddr->lbal_addr = ioaddr->cmd_addr + (ATA_REG_LBAL << 2); |
| ioaddr->lbam_addr = ioaddr->cmd_addr + (ATA_REG_LBAM << 2); |
| ioaddr->lbah_addr = ioaddr->cmd_addr + (ATA_REG_LBAH << 2); |
| ioaddr->device_addr = ioaddr->cmd_addr + (ATA_REG_DEVICE << 2); |
| ioaddr->status_addr = ioaddr->cmd_addr + (ATA_REG_STATUS << 2); |
| ioaddr->command_addr = ioaddr->cmd_addr + (ATA_REG_CMD << 2); |
| } |
| |
| static void sata_rcar_init_controller(struct ata_host *host) |
| { |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| u32 val; |
| |
| /* reset and setup phy */ |
| switch (priv->type) { |
| case RCAR_GEN1_SATA: |
| sata_rcar_gen1_phy_init(priv); |
| break; |
| case RCAR_GEN2_SATA: |
| case RCAR_R8A7790_ES1_SATA: |
| sata_rcar_gen2_phy_init(priv); |
| break; |
| default: |
| dev_warn(host->dev, "SATA phy is not initialized\n"); |
| break; |
| } |
| |
| /* SATA-IP reset state */ |
| val = ioread32(base + ATAPI_CONTROL1_REG); |
| val |= ATAPI_CONTROL1_RESET; |
| iowrite32(val, base + ATAPI_CONTROL1_REG); |
| |
| /* ISM mode, PRD mode, DTEND flag at bit 0 */ |
| val = ioread32(base + ATAPI_CONTROL1_REG); |
| val |= ATAPI_CONTROL1_ISM; |
| val |= ATAPI_CONTROL1_DESE; |
| val |= ATAPI_CONTROL1_DTA32M; |
| iowrite32(val, base + ATAPI_CONTROL1_REG); |
| |
| /* Release the SATA-IP from the reset state */ |
| val = ioread32(base + ATAPI_CONTROL1_REG); |
| val &= ~ATAPI_CONTROL1_RESET; |
| iowrite32(val, base + ATAPI_CONTROL1_REG); |
| |
| /* ack and mask */ |
| iowrite32(0, base + SATAINTSTAT_REG); |
| iowrite32(0x7ff, base + SATAINTMASK_REG); |
| /* enable interrupts */ |
| iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG); |
| } |
| |
| static struct of_device_id sata_rcar_match[] = { |
| { |
| /* Deprecated by "renesas,sata-r8a7779" */ |
| .compatible = "renesas,rcar-sata", |
| .data = (void *)RCAR_GEN1_SATA, |
| }, |
| { |
| .compatible = "renesas,sata-r8a7779", |
| .data = (void *)RCAR_GEN1_SATA, |
| }, |
| { |
| .compatible = "renesas,sata-r8a7790", |
| .data = (void *)RCAR_GEN2_SATA |
| }, |
| { |
| .compatible = "renesas,sata-r8a7790-es1", |
| .data = (void *)RCAR_R8A7790_ES1_SATA |
| }, |
| { |
| .compatible = "renesas,sata-r8a7791", |
| .data = (void *)RCAR_GEN2_SATA |
| }, |
| { |
| .compatible = "renesas,sata-r8a7793", |
| .data = (void *)RCAR_GEN2_SATA |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, sata_rcar_match); |
| |
| static const struct platform_device_id sata_rcar_id_table[] = { |
| { "sata_rcar", RCAR_GEN1_SATA }, /* Deprecated by "sata-r8a7779" */ |
| { "sata-r8a7779", RCAR_GEN1_SATA }, |
| { "sata-r8a7790", RCAR_GEN2_SATA }, |
| { "sata-r8a7790-es1", RCAR_R8A7790_ES1_SATA }, |
| { "sata-r8a7791", RCAR_GEN2_SATA }, |
| { "sata-r8a7793", RCAR_GEN2_SATA }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(platform, sata_rcar_id_table); |
| |
| static int sata_rcar_probe(struct platform_device *pdev) |
| { |
| const struct of_device_id *of_id; |
| struct ata_host *host; |
| struct sata_rcar_priv *priv; |
| struct resource *mem; |
| int irq; |
| int ret = 0; |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq <= 0) |
| return -EINVAL; |
| |
| priv = devm_kzalloc(&pdev->dev, sizeof(struct sata_rcar_priv), |
| GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| of_id = of_match_device(sata_rcar_match, &pdev->dev); |
| if (of_id) |
| priv->type = (enum sata_rcar_type)of_id->data; |
| else |
| priv->type = platform_get_device_id(pdev)->driver_data; |
| |
| priv->clk = devm_clk_get(&pdev->dev, NULL); |
| if (IS_ERR(priv->clk)) { |
| dev_err(&pdev->dev, "failed to get access to sata clock\n"); |
| return PTR_ERR(priv->clk); |
| } |
| clk_prepare_enable(priv->clk); |
| |
| host = ata_host_alloc(&pdev->dev, 1); |
| if (!host) { |
| dev_err(&pdev->dev, "ata_host_alloc failed\n"); |
| ret = -ENOMEM; |
| goto cleanup; |
| } |
| |
| host->private_data = priv; |
| |
| mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| priv->base = devm_ioremap_resource(&pdev->dev, mem); |
| if (IS_ERR(priv->base)) { |
| ret = PTR_ERR(priv->base); |
| goto cleanup; |
| } |
| |
| /* setup port */ |
| sata_rcar_setup_port(host); |
| |
| /* initialize host controller */ |
| sata_rcar_init_controller(host); |
| |
| ret = ata_host_activate(host, irq, sata_rcar_interrupt, 0, |
| &sata_rcar_sht); |
| if (!ret) |
| return 0; |
| |
| cleanup: |
| clk_disable_unprepare(priv->clk); |
| |
| return ret; |
| } |
| |
| static int sata_rcar_remove(struct platform_device *pdev) |
| { |
| struct ata_host *host = platform_get_drvdata(pdev); |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| |
| ata_host_detach(host); |
| |
| /* disable interrupts */ |
| iowrite32(0, base + ATAPI_INT_ENABLE_REG); |
| /* ack and mask */ |
| iowrite32(0, base + SATAINTSTAT_REG); |
| iowrite32(0x7ff, base + SATAINTMASK_REG); |
| |
| clk_disable_unprepare(priv->clk); |
| |
| return 0; |
| } |
| |
| #ifdef CONFIG_PM_SLEEP |
| static int sata_rcar_suspend(struct device *dev) |
| { |
| struct ata_host *host = dev_get_drvdata(dev); |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| int ret; |
| |
| ret = ata_host_suspend(host, PMSG_SUSPEND); |
| if (!ret) { |
| /* disable interrupts */ |
| iowrite32(0, base + ATAPI_INT_ENABLE_REG); |
| /* mask */ |
| iowrite32(0x7ff, base + SATAINTMASK_REG); |
| |
| clk_disable_unprepare(priv->clk); |
| } |
| |
| return ret; |
| } |
| |
| static int sata_rcar_resume(struct device *dev) |
| { |
| struct ata_host *host = dev_get_drvdata(dev); |
| struct sata_rcar_priv *priv = host->private_data; |
| void __iomem *base = priv->base; |
| |
| clk_prepare_enable(priv->clk); |
| |
| /* ack and mask */ |
| iowrite32(0, base + SATAINTSTAT_REG); |
| iowrite32(0x7ff, base + SATAINTMASK_REG); |
| /* enable interrupts */ |
| iowrite32(ATAPI_INT_ENABLE_SATAINT, base + ATAPI_INT_ENABLE_REG); |
| |
| ata_host_resume(host); |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops sata_rcar_pm_ops = { |
| .suspend = sata_rcar_suspend, |
| .resume = sata_rcar_resume, |
| }; |
| #endif |
| |
| static struct platform_driver sata_rcar_driver = { |
| .probe = sata_rcar_probe, |
| .remove = sata_rcar_remove, |
| .id_table = sata_rcar_id_table, |
| .driver = { |
| .name = DRV_NAME, |
| .owner = THIS_MODULE, |
| .of_match_table = sata_rcar_match, |
| #ifdef CONFIG_PM_SLEEP |
| .pm = &sata_rcar_pm_ops, |
| #endif |
| }, |
| }; |
| |
| module_platform_driver(sata_rcar_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_AUTHOR("Vladimir Barinov"); |
| MODULE_DESCRIPTION("Renesas R-Car SATA controller low level driver"); |