blob: 2413778f371507ec2caa8b82eb77a726191417a6 [file] [log] [blame]
// SPDX-License-Identifier: BSD-3-Clause
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
/ {
thermal-zones {
pm8226-thermal {
polling-delay-passive = <100>;
polling-delay = <0>;
thermal-sensors = <&pm8226_temp>;
trips {
trip0 {
temperature = <105000>;
hysteresis = <2000>;
type = "passive";
};
trip1 {
temperature = <125000>;
hysteresis = <2000>;
type = "hot";
};
crit {
temperature = <145000>;
hysteresis = <2000>;
type = "critical";
};
};
};
};
};
&spmi_bus {
pm8226_0: pm8226@0 {
compatible = "qcom,pm8226", "qcom,spmi-pmic";
reg = <0x0 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pon@800 {
compatible = "qcom,pm8916-pon";
reg = <0x800>;
pwrkey {
compatible = "qcom,pm8941-pwrkey";
interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_POWER>;
};
pm8226_resin: resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
status = "disabled";
};
};
smbb: charger@1000 {
compatible = "qcom,pm8226-charger";
reg = <0x1000>;
interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
<0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
interrupt-names = "chg-done",
"chg-fast",
"chg-trkl",
"bat-temp-ok",
"bat-present",
"chg-gone",
"usb-valid",
"dc-valid";
chg_otg: otg-vbus { };
};
pm8226_temp: temp-alarm@2400 {
compatible = "qcom,spmi-temp-alarm";
reg = <0x2400>;
interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
io-channels = <&pm8226_vadc VADC_DIE_TEMP>;
io-channel-names = "thermal";
#thermal-sensor-cells = <0>;
};
pm8226_vadc: adc@3100 {
compatible = "qcom,spmi-vadc";
reg = <0x3100>;
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
#address-cells = <1>;
#size-cells = <0>;
#io-channel-cells = <1>;
channel@7 {
reg = <VADC_VSYS>;
qcom,pre-scaling = <1 3>;
label = "vph_pwr";
};
channel@8 {
reg = <VADC_DIE_TEMP>;
label = "die_temp";
};
channel@9 {
reg = <VADC_REF_625MV>;
label = "ref_625mv";
};
channel@a {
reg = <VADC_REF_1250MV>;
label = "ref_1250mv";
};
channel@e {
reg = <VADC_GND_REF>;
};
channel@f {
reg = <VADC_VDD_VADC>;
};
};
pm8226_iadc: adc@3600 {
compatible = "qcom,pm8226-iadc", "qcom,spmi-iadc";
reg = <0x3600>;
interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
};
rtc@6000 {
compatible = "qcom,pm8941-rtc";
reg = <0x6000>, <0x6100>;
reg-names = "rtc", "alarm";
interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
};
pm8226_mpps: mpps@a000 {
compatible = "qcom,pm8226-mpp", "qcom,spmi-mpp";
reg = <0xa000>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pm8226_mpps 0 0 8>;
interrupt-controller;
#interrupt-cells = <2>;
};
pm8226_gpios: gpio@c000 {
compatible = "qcom,pm8226-gpio", "qcom,spmi-gpio";
reg = <0xc000>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&pm8226_gpios 0 0 8>;
interrupt-controller;
#interrupt-cells = <2>;
};
};
pm8226_1: pm8226@1 {
compatible = "qcom,pm8226", "qcom,spmi-pmic";
reg = <0x1 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
pm8226_spmi_regulators: regulators {
compatible = "qcom,pm8226-regulators";
};
pm8226_vib: vibrator@c000 {
compatible = "qcom,pm8916-vib";
reg = <0xc000>;
status = "disabled";
};
};
};