| // SPDX-License-Identifier: GPL-1.0+ |
| /* |
| * Renesas USB driver |
| * |
| * Copyright (C) 2011 Renesas Solutions Corp. |
| * Copyright (C) 2019 Renesas Electronics Corporation |
| * Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> |
| */ |
| #include <linux/clk.h> |
| #include <linux/err.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/io.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/reset.h> |
| #include <linux/slab.h> |
| #include <linux/sysfs.h> |
| #include "common.h" |
| #include "rcar2.h" |
| #include "rcar3.h" |
| #include "rza.h" |
| |
| /* |
| * image of renesas_usbhs |
| * |
| * ex) gadget case |
| |
| * mod.c |
| * mod_gadget.c |
| * mod_host.c pipe.c fifo.c |
| * |
| * +-------+ +-----------+ |
| * | pipe0 |------>| fifo pio | |
| * +------------+ +-------+ +-----------+ |
| * | mod_gadget |=====> | pipe1 |--+ |
| * +------------+ +-------+ | +-----------+ |
| * | pipe2 | | +-| fifo dma0 | |
| * +------------+ +-------+ | | +-----------+ |
| * | mod_host | | pipe3 |<-|--+ |
| * +------------+ +-------+ | +-----------+ |
| * | .... | +--->| fifo dma1 | |
| * | .... | +-----------+ |
| */ |
| |
| /* |
| * platform call back |
| * |
| * renesas usb support platform callback function. |
| * Below macro call it. |
| * if platform doesn't have callback, it return 0 (no error) |
| */ |
| #define usbhs_platform_call(priv, func, args...)\ |
| (!(priv) ? -ENODEV : \ |
| !((priv)->pfunc->func) ? 0 : \ |
| (priv)->pfunc->func(args)) |
| |
| /* |
| * common functions |
| */ |
| u16 usbhs_read(struct usbhs_priv *priv, u32 reg) |
| { |
| return ioread16(priv->base + reg); |
| } |
| |
| void usbhs_write(struct usbhs_priv *priv, u32 reg, u16 data) |
| { |
| iowrite16(data, priv->base + reg); |
| } |
| |
| void usbhs_bset(struct usbhs_priv *priv, u32 reg, u16 mask, u16 data) |
| { |
| u16 val = usbhs_read(priv, reg); |
| |
| val &= ~mask; |
| val |= data & mask; |
| |
| usbhs_write(priv, reg, val); |
| } |
| |
| struct usbhs_priv *usbhs_pdev_to_priv(struct platform_device *pdev) |
| { |
| return dev_get_drvdata(&pdev->dev); |
| } |
| |
| int usbhs_get_id_as_gadget(struct platform_device *pdev) |
| { |
| return USBHS_GADGET; |
| } |
| |
| /* |
| * syscfg functions |
| */ |
| static void usbhs_sys_clock_ctrl(struct usbhs_priv *priv, int enable) |
| { |
| usbhs_bset(priv, SYSCFG, SCKE, enable ? SCKE : 0); |
| } |
| |
| void usbhs_sys_host_ctrl(struct usbhs_priv *priv, int enable) |
| { |
| u16 mask = DCFM | DRPD | DPRPU | HSE | USBE; |
| u16 val = DCFM | DRPD | HSE | USBE; |
| |
| /* |
| * if enable |
| * |
| * - select Host mode |
| * - D+ Line/D- Line Pull-down |
| */ |
| usbhs_bset(priv, SYSCFG, mask, enable ? val : 0); |
| } |
| |
| void usbhs_sys_function_ctrl(struct usbhs_priv *priv, int enable) |
| { |
| u16 mask = DCFM | DRPD | DPRPU | HSE | USBE; |
| u16 val = HSE | USBE; |
| |
| /* CNEN bit is required for function operation */ |
| if (usbhs_get_dparam(priv, has_cnen)) { |
| mask |= CNEN; |
| val |= CNEN; |
| } |
| |
| /* |
| * if enable |
| * |
| * - select Function mode |
| * - D+ Line Pull-up is disabled |
| * When D+ Line Pull-up is enabled, |
| * calling usbhs_sys_function_pullup(,1) |
| */ |
| usbhs_bset(priv, SYSCFG, mask, enable ? val : 0); |
| } |
| |
| void usbhs_sys_function_pullup(struct usbhs_priv *priv, int enable) |
| { |
| usbhs_bset(priv, SYSCFG, DPRPU, enable ? DPRPU : 0); |
| } |
| |
| void usbhs_sys_set_test_mode(struct usbhs_priv *priv, u16 mode) |
| { |
| usbhs_write(priv, TESTMODE, mode); |
| } |
| |
| /* |
| * frame functions |
| */ |
| int usbhs_frame_get_num(struct usbhs_priv *priv) |
| { |
| return usbhs_read(priv, FRMNUM) & FRNM_MASK; |
| } |
| |
| /* |
| * usb request functions |
| */ |
| void usbhs_usbreq_get_val(struct usbhs_priv *priv, struct usb_ctrlrequest *req) |
| { |
| u16 val; |
| |
| val = usbhs_read(priv, USBREQ); |
| req->bRequest = (val >> 8) & 0xFF; |
| req->bRequestType = (val >> 0) & 0xFF; |
| |
| req->wValue = cpu_to_le16(usbhs_read(priv, USBVAL)); |
| req->wIndex = cpu_to_le16(usbhs_read(priv, USBINDX)); |
| req->wLength = cpu_to_le16(usbhs_read(priv, USBLENG)); |
| } |
| |
| void usbhs_usbreq_set_val(struct usbhs_priv *priv, struct usb_ctrlrequest *req) |
| { |
| usbhs_write(priv, USBREQ, (req->bRequest << 8) | req->bRequestType); |
| usbhs_write(priv, USBVAL, le16_to_cpu(req->wValue)); |
| usbhs_write(priv, USBINDX, le16_to_cpu(req->wIndex)); |
| usbhs_write(priv, USBLENG, le16_to_cpu(req->wLength)); |
| |
| usbhs_bset(priv, DCPCTR, SUREQ, SUREQ); |
| } |
| |
| /* |
| * bus/vbus functions |
| */ |
| void usbhs_bus_send_sof_enable(struct usbhs_priv *priv) |
| { |
| u16 status = usbhs_read(priv, DVSTCTR) & (USBRST | UACT); |
| |
| if (status != USBRST) { |
| struct device *dev = usbhs_priv_to_dev(priv); |
| dev_err(dev, "usbhs should be reset\n"); |
| } |
| |
| usbhs_bset(priv, DVSTCTR, (USBRST | UACT), UACT); |
| } |
| |
| void usbhs_bus_send_reset(struct usbhs_priv *priv) |
| { |
| usbhs_bset(priv, DVSTCTR, (USBRST | UACT), USBRST); |
| } |
| |
| int usbhs_bus_get_speed(struct usbhs_priv *priv) |
| { |
| u16 dvstctr = usbhs_read(priv, DVSTCTR); |
| |
| switch (RHST & dvstctr) { |
| case RHST_LOW_SPEED: |
| return USB_SPEED_LOW; |
| case RHST_FULL_SPEED: |
| return USB_SPEED_FULL; |
| case RHST_HIGH_SPEED: |
| return USB_SPEED_HIGH; |
| } |
| |
| return USB_SPEED_UNKNOWN; |
| } |
| |
| int usbhs_vbus_ctrl(struct usbhs_priv *priv, int enable) |
| { |
| struct platform_device *pdev = usbhs_priv_to_pdev(priv); |
| |
| return usbhs_platform_call(priv, set_vbus, pdev, enable); |
| } |
| |
| static void usbhsc_bus_init(struct usbhs_priv *priv) |
| { |
| usbhs_write(priv, DVSTCTR, 0); |
| |
| usbhs_vbus_ctrl(priv, 0); |
| } |
| |
| /* |
| * device configuration |
| */ |
| int usbhs_set_device_config(struct usbhs_priv *priv, int devnum, |
| u16 upphub, u16 hubport, u16 speed) |
| { |
| struct device *dev = usbhs_priv_to_dev(priv); |
| u16 usbspd = 0; |
| u32 reg = DEVADD0 + (2 * devnum); |
| |
| if (devnum > 10) { |
| dev_err(dev, "cannot set speed to unknown device %d\n", devnum); |
| return -EIO; |
| } |
| |
| if (upphub > 0xA) { |
| dev_err(dev, "unsupported hub number %d\n", upphub); |
| return -EIO; |
| } |
| |
| switch (speed) { |
| case USB_SPEED_LOW: |
| usbspd = USBSPD_SPEED_LOW; |
| break; |
| case USB_SPEED_FULL: |
| usbspd = USBSPD_SPEED_FULL; |
| break; |
| case USB_SPEED_HIGH: |
| usbspd = USBSPD_SPEED_HIGH; |
| break; |
| default: |
| dev_err(dev, "unsupported speed %d\n", speed); |
| return -EIO; |
| } |
| |
| usbhs_write(priv, reg, UPPHUB(upphub) | |
| HUBPORT(hubport)| |
| USBSPD(usbspd)); |
| |
| return 0; |
| } |
| |
| /* |
| * interrupt functions |
| */ |
| void usbhs_xxxsts_clear(struct usbhs_priv *priv, u16 sts_reg, u16 bit) |
| { |
| u16 pipe_mask = (u16)GENMASK(usbhs_get_dparam(priv, pipe_size), 0); |
| |
| usbhs_write(priv, sts_reg, ~(1 << bit) & pipe_mask); |
| } |
| |
| /* |
| * local functions |
| */ |
| static void usbhsc_set_buswait(struct usbhs_priv *priv) |
| { |
| int wait = usbhs_get_dparam(priv, buswait_bwait); |
| |
| /* set bus wait if platform have */ |
| if (wait) |
| usbhs_bset(priv, BUSWAIT, 0x000F, wait); |
| } |
| |
| static bool usbhsc_is_multi_clks(struct usbhs_priv *priv) |
| { |
| return priv->dparam.multi_clks; |
| } |
| |
| static int usbhsc_clk_get(struct device *dev, struct usbhs_priv *priv) |
| { |
| if (!usbhsc_is_multi_clks(priv)) |
| return 0; |
| |
| /* The first clock should exist */ |
| priv->clks[0] = of_clk_get(dev_of_node(dev), 0); |
| if (IS_ERR(priv->clks[0])) |
| return PTR_ERR(priv->clks[0]); |
| |
| /* |
| * To backward compatibility with old DT, this driver checks the return |
| * value if it's -ENOENT or not. |
| */ |
| priv->clks[1] = of_clk_get(dev_of_node(dev), 1); |
| if (PTR_ERR(priv->clks[1]) == -ENOENT) |
| priv->clks[1] = NULL; |
| else if (IS_ERR(priv->clks[1])) |
| return PTR_ERR(priv->clks[1]); |
| |
| return 0; |
| } |
| |
| static void usbhsc_clk_put(struct usbhs_priv *priv) |
| { |
| int i; |
| |
| if (!usbhsc_is_multi_clks(priv)) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(priv->clks); i++) |
| clk_put(priv->clks[i]); |
| } |
| |
| static int usbhsc_clk_prepare_enable(struct usbhs_priv *priv) |
| { |
| int i, ret; |
| |
| if (!usbhsc_is_multi_clks(priv)) |
| return 0; |
| |
| for (i = 0; i < ARRAY_SIZE(priv->clks); i++) { |
| ret = clk_prepare_enable(priv->clks[i]); |
| if (ret) { |
| while (--i >= 0) |
| clk_disable_unprepare(priv->clks[i]); |
| return ret; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static void usbhsc_clk_disable_unprepare(struct usbhs_priv *priv) |
| { |
| int i; |
| |
| if (!usbhsc_is_multi_clks(priv)) |
| return; |
| |
| for (i = 0; i < ARRAY_SIZE(priv->clks); i++) |
| clk_disable_unprepare(priv->clks[i]); |
| } |
| |
| /* |
| * platform default param |
| */ |
| |
| /* commonly used on old SH-Mobile SoCs */ |
| static struct renesas_usbhs_driver_pipe_config usbhsc_default_pipe[] = { |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_CONTROL, 64, 0x00, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_ISOC, 1024, 0x08, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_ISOC, 1024, 0x18, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x28, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x38, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x48, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x04, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x05, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x06, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x07, false), |
| }; |
| |
| /* commonly used on newer SH-Mobile and R-Car SoCs */ |
| static struct renesas_usbhs_driver_pipe_config usbhsc_new_pipe[] = { |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_CONTROL, 64, 0x00, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_ISOC, 1024, 0x08, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_ISOC, 1024, 0x28, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x48, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x58, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x68, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x04, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x05, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_INT, 64, 0x06, false), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x78, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x88, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0x98, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0xa8, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0xb8, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0xc8, true), |
| RENESAS_USBHS_PIPE(USB_ENDPOINT_XFER_BULK, 512, 0xd8, true), |
| }; |
| |
| /* |
| * power control |
| */ |
| static void usbhsc_power_ctrl(struct usbhs_priv *priv, int enable) |
| { |
| struct platform_device *pdev = usbhs_priv_to_pdev(priv); |
| struct device *dev = usbhs_priv_to_dev(priv); |
| |
| if (enable) { |
| /* enable PM */ |
| pm_runtime_get_sync(dev); |
| |
| /* enable clks */ |
| if (usbhsc_clk_prepare_enable(priv)) |
| return; |
| |
| /* enable platform power */ |
| usbhs_platform_call(priv, power_ctrl, pdev, priv->base, enable); |
| |
| /* USB on */ |
| usbhs_sys_clock_ctrl(priv, enable); |
| } else { |
| /* USB off */ |
| usbhs_sys_clock_ctrl(priv, enable); |
| |
| /* disable platform power */ |
| usbhs_platform_call(priv, power_ctrl, pdev, priv->base, enable); |
| |
| /* disable clks */ |
| usbhsc_clk_disable_unprepare(priv); |
| |
| /* disable PM */ |
| pm_runtime_put_sync(dev); |
| } |
| } |
| |
| /* |
| * hotplug |
| */ |
| static void usbhsc_hotplug(struct usbhs_priv *priv) |
| { |
| struct platform_device *pdev = usbhs_priv_to_pdev(priv); |
| struct usbhs_mod *mod = usbhs_mod_get_current(priv); |
| int id; |
| int enable; |
| int cable; |
| int ret; |
| |
| /* |
| * get vbus status from platform |
| */ |
| enable = usbhs_mod_info_call(priv, get_vbus, pdev); |
| |
| /* |
| * get id from platform |
| */ |
| id = usbhs_platform_call(priv, get_id, pdev); |
| |
| if (enable && !mod) { |
| if (priv->edev) { |
| cable = extcon_get_state(priv->edev, EXTCON_USB_HOST); |
| if ((cable > 0 && id != USBHS_HOST) || |
| (!cable && id != USBHS_GADGET)) { |
| dev_info(&pdev->dev, |
| "USB cable plugged in doesn't match the selected role!\n"); |
| return; |
| } |
| } |
| |
| ret = usbhs_mod_change(priv, id); |
| if (ret < 0) |
| return; |
| |
| dev_dbg(&pdev->dev, "%s enable\n", __func__); |
| |
| /* power on */ |
| if (usbhs_get_dparam(priv, runtime_pwctrl)) |
| usbhsc_power_ctrl(priv, enable); |
| |
| /* bus init */ |
| usbhsc_set_buswait(priv); |
| usbhsc_bus_init(priv); |
| |
| /* module start */ |
| usbhs_mod_call(priv, start, priv); |
| |
| } else if (!enable && mod) { |
| dev_dbg(&pdev->dev, "%s disable\n", __func__); |
| |
| /* module stop */ |
| usbhs_mod_call(priv, stop, priv); |
| |
| /* bus init */ |
| usbhsc_bus_init(priv); |
| |
| /* power off */ |
| if (usbhs_get_dparam(priv, runtime_pwctrl)) |
| usbhsc_power_ctrl(priv, enable); |
| |
| usbhs_mod_change(priv, -1); |
| |
| /* reset phy for next connection */ |
| usbhs_platform_call(priv, phy_reset, pdev); |
| } |
| } |
| |
| /* |
| * notify hotplug |
| */ |
| static void usbhsc_notify_hotplug(struct work_struct *work) |
| { |
| struct usbhs_priv *priv = container_of(work, |
| struct usbhs_priv, |
| notify_hotplug_work.work); |
| usbhsc_hotplug(priv); |
| } |
| |
| int usbhsc_schedule_notify_hotplug(struct platform_device *pdev) |
| { |
| struct usbhs_priv *priv = usbhs_pdev_to_priv(pdev); |
| int delay = usbhs_get_dparam(priv, detection_delay); |
| |
| /* |
| * This functions will be called in interrupt. |
| * To make sure safety context, |
| * use workqueue for usbhs_notify_hotplug |
| */ |
| schedule_delayed_work(&priv->notify_hotplug_work, |
| msecs_to_jiffies(delay)); |
| return 0; |
| } |
| |
| /* |
| * platform functions |
| */ |
| static const struct of_device_id usbhs_of_match[] = { |
| { |
| .compatible = "renesas,usbhs-r8a774c0", |
| .data = &usbhs_rcar_gen3_with_pll_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a7790", |
| .data = &usbhs_rcar_gen2_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a7791", |
| .data = &usbhs_rcar_gen2_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a7794", |
| .data = &usbhs_rcar_gen2_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a7795", |
| .data = &usbhs_rcar_gen3_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a7796", |
| .data = &usbhs_rcar_gen3_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a77990", |
| .data = &usbhs_rcar_gen3_with_pll_plat_info, |
| }, |
| { |
| .compatible = "renesas,usbhs-r8a77995", |
| .data = &usbhs_rcar_gen3_with_pll_plat_info, |
| }, |
| { |
| .compatible = "renesas,rcar-gen2-usbhs", |
| .data = &usbhs_rcar_gen2_plat_info, |
| }, |
| { |
| .compatible = "renesas,rcar-gen3-usbhs", |
| .data = &usbhs_rcar_gen3_plat_info, |
| }, |
| { |
| .compatible = "renesas,rza1-usbhs", |
| .data = &usbhs_rza1_plat_info, |
| }, |
| { |
| .compatible = "renesas,rza2-usbhs", |
| .data = &usbhs_rza2_plat_info, |
| }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, usbhs_of_match); |
| |
| static int usbhs_probe(struct platform_device *pdev) |
| { |
| const struct renesas_usbhs_platform_info *info; |
| struct usbhs_priv *priv; |
| struct device *dev = &pdev->dev; |
| struct gpio_desc *gpiod; |
| int ret; |
| u32 tmp; |
| int irq; |
| |
| /* check device node */ |
| if (dev_of_node(dev)) |
| info = of_device_get_match_data(dev); |
| else |
| info = renesas_usbhs_get_info(pdev); |
| |
| /* check platform information */ |
| if (!info) { |
| dev_err(dev, "no platform information\n"); |
| return -EINVAL; |
| } |
| |
| /* platform data */ |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| /* usb private data */ |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| priv->base = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(priv->base)) |
| return PTR_ERR(priv->base); |
| |
| if (of_property_read_bool(dev_of_node(dev), "extcon")) { |
| priv->edev = extcon_get_edev_by_phandle(dev, 0); |
| if (IS_ERR(priv->edev)) |
| return PTR_ERR(priv->edev); |
| } |
| |
| priv->rsts = devm_reset_control_array_get_optional_shared(dev); |
| if (IS_ERR(priv->rsts)) |
| return PTR_ERR(priv->rsts); |
| |
| /* |
| * care platform info |
| */ |
| |
| priv->dparam = info->driver_param; |
| |
| if (!info->platform_callback.get_id) { |
| dev_err(dev, "no platform callbacks\n"); |
| return -EINVAL; |
| } |
| priv->pfunc = &info->platform_callback; |
| |
| /* set default param if platform doesn't have */ |
| if (usbhs_get_dparam(priv, has_new_pipe_configs)) { |
| priv->dparam.pipe_configs = usbhsc_new_pipe; |
| priv->dparam.pipe_size = ARRAY_SIZE(usbhsc_new_pipe); |
| } else if (!priv->dparam.pipe_configs) { |
| priv->dparam.pipe_configs = usbhsc_default_pipe; |
| priv->dparam.pipe_size = ARRAY_SIZE(usbhsc_default_pipe); |
| } |
| if (!priv->dparam.pio_dma_border) |
| priv->dparam.pio_dma_border = 64; /* 64byte */ |
| if (!of_property_read_u32(dev_of_node(dev), "renesas,buswait", &tmp)) |
| priv->dparam.buswait_bwait = tmp; |
| gpiod = devm_gpiod_get_optional(dev, "renesas,enable", GPIOD_IN); |
| if (IS_ERR(gpiod)) |
| return PTR_ERR(gpiod); |
| |
| /* FIXME */ |
| /* runtime power control ? */ |
| if (priv->pfunc->get_vbus) |
| usbhs_get_dparam(priv, runtime_pwctrl) = 1; |
| |
| /* |
| * priv settings |
| */ |
| priv->irq = irq; |
| priv->pdev = pdev; |
| INIT_DELAYED_WORK(&priv->notify_hotplug_work, usbhsc_notify_hotplug); |
| spin_lock_init(usbhs_priv_to_lock(priv)); |
| |
| /* call pipe and module init */ |
| ret = usbhs_pipe_probe(priv); |
| if (ret < 0) |
| return ret; |
| |
| ret = usbhs_fifo_probe(priv); |
| if (ret < 0) |
| goto probe_end_pipe_exit; |
| |
| ret = usbhs_mod_probe(priv); |
| if (ret < 0) |
| goto probe_end_fifo_exit; |
| |
| /* dev_set_drvdata should be called after usbhs_mod_init */ |
| platform_set_drvdata(pdev, priv); |
| |
| ret = reset_control_deassert(priv->rsts); |
| if (ret) |
| goto probe_fail_rst; |
| |
| ret = usbhsc_clk_get(dev, priv); |
| if (ret) |
| goto probe_fail_clks; |
| |
| /* |
| * deviece reset here because |
| * USB device might be used in boot loader. |
| */ |
| usbhs_sys_clock_ctrl(priv, 0); |
| |
| /* check GPIO determining if USB function should be enabled */ |
| if (gpiod) { |
| ret = !gpiod_get_value(gpiod); |
| if (ret) { |
| dev_warn(dev, "USB function not selected (GPIO)\n"); |
| ret = -ENOTSUPP; |
| goto probe_end_mod_exit; |
| } |
| } |
| |
| /* |
| * platform call |
| * |
| * USB phy setup might depend on CPU/Board. |
| * If platform has its callback functions, |
| * call it here. |
| */ |
| ret = usbhs_platform_call(priv, hardware_init, pdev); |
| if (ret < 0) { |
| dev_err(dev, "platform init failed.\n"); |
| goto probe_end_mod_exit; |
| } |
| |
| /* reset phy for connection */ |
| usbhs_platform_call(priv, phy_reset, pdev); |
| |
| /* power control */ |
| pm_runtime_enable(dev); |
| if (!usbhs_get_dparam(priv, runtime_pwctrl)) { |
| usbhsc_power_ctrl(priv, 1); |
| usbhs_mod_autonomy_mode(priv); |
| } else { |
| usbhs_mod_non_autonomy_mode(priv); |
| } |
| |
| /* |
| * manual call notify_hotplug for cold plug |
| */ |
| usbhsc_schedule_notify_hotplug(pdev); |
| |
| dev_info(dev, "probed\n"); |
| |
| return ret; |
| |
| probe_end_mod_exit: |
| usbhsc_clk_put(priv); |
| probe_fail_clks: |
| reset_control_assert(priv->rsts); |
| probe_fail_rst: |
| usbhs_mod_remove(priv); |
| probe_end_fifo_exit: |
| usbhs_fifo_remove(priv); |
| probe_end_pipe_exit: |
| usbhs_pipe_remove(priv); |
| |
| dev_info(dev, "probe failed (%d)\n", ret); |
| |
| return ret; |
| } |
| |
| static int usbhs_remove(struct platform_device *pdev) |
| { |
| struct usbhs_priv *priv = usbhs_pdev_to_priv(pdev); |
| |
| dev_dbg(&pdev->dev, "usb remove\n"); |
| |
| /* power off */ |
| if (!usbhs_get_dparam(priv, runtime_pwctrl)) |
| usbhsc_power_ctrl(priv, 0); |
| |
| pm_runtime_disable(&pdev->dev); |
| |
| usbhs_platform_call(priv, hardware_exit, pdev); |
| usbhsc_clk_put(priv); |
| reset_control_assert(priv->rsts); |
| usbhs_mod_remove(priv); |
| usbhs_fifo_remove(priv); |
| usbhs_pipe_remove(priv); |
| |
| return 0; |
| } |
| |
| static __maybe_unused int usbhsc_suspend(struct device *dev) |
| { |
| struct usbhs_priv *priv = dev_get_drvdata(dev); |
| struct usbhs_mod *mod = usbhs_mod_get_current(priv); |
| |
| if (mod) { |
| usbhs_mod_call(priv, stop, priv); |
| usbhs_mod_change(priv, -1); |
| } |
| |
| if (mod || !usbhs_get_dparam(priv, runtime_pwctrl)) |
| usbhsc_power_ctrl(priv, 0); |
| |
| return 0; |
| } |
| |
| static __maybe_unused int usbhsc_resume(struct device *dev) |
| { |
| struct usbhs_priv *priv = dev_get_drvdata(dev); |
| struct platform_device *pdev = usbhs_priv_to_pdev(priv); |
| |
| if (!usbhs_get_dparam(priv, runtime_pwctrl)) { |
| usbhsc_power_ctrl(priv, 1); |
| usbhs_mod_autonomy_mode(priv); |
| } |
| |
| usbhs_platform_call(priv, phy_reset, pdev); |
| |
| usbhsc_schedule_notify_hotplug(pdev); |
| |
| return 0; |
| } |
| |
| static SIMPLE_DEV_PM_OPS(usbhsc_pm_ops, usbhsc_suspend, usbhsc_resume); |
| |
| static struct platform_driver renesas_usbhs_driver = { |
| .driver = { |
| .name = "renesas_usbhs", |
| .pm = &usbhsc_pm_ops, |
| .of_match_table = usbhs_of_match, |
| }, |
| .probe = usbhs_probe, |
| .remove = usbhs_remove, |
| }; |
| |
| module_platform_driver(renesas_usbhs_driver); |
| |
| MODULE_LICENSE("GPL"); |
| MODULE_DESCRIPTION("Renesas USB driver"); |
| MODULE_AUTHOR("Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>"); |