| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Samsung CSIS MIPI CSI-2 receiver driver. |
| * |
| * The Samsung CSIS IP is a MIPI CSI-2 receiver found in various NXP i.MX7 and |
| * i.MX8 SoCs. The i.MX7 features version 3.3 of the IP, while i.MX8 features |
| * version 3.6.3. |
| * |
| * Copyright (C) 2019 Linaro Ltd |
| * Copyright (C) 2015-2016 Freescale Semiconductor, Inc. All Rights Reserved. |
| * Copyright (C) 2011 - 2013 Samsung Electronics Co., Ltd. |
| * |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/debugfs.h> |
| #include <linux/delay.h> |
| #include <linux/errno.h> |
| #include <linux/interrupt.h> |
| #include <linux/io.h> |
| #include <linux/kernel.h> |
| #include <linux/module.h> |
| #include <linux/mutex.h> |
| #include <linux/of.h> |
| #include <linux/platform_device.h> |
| #include <linux/pm_runtime.h> |
| #include <linux/regulator/consumer.h> |
| #include <linux/reset.h> |
| #include <linux/spinlock.h> |
| |
| #include <media/v4l2-common.h> |
| #include <media/v4l2-device.h> |
| #include <media/v4l2-fwnode.h> |
| #include <media/v4l2-mc.h> |
| #include <media/v4l2-subdev.h> |
| |
| #define CSIS_DRIVER_NAME "imx-mipi-csis" |
| |
| #define CSIS_PAD_SINK 0 |
| #define CSIS_PAD_SOURCE 1 |
| #define CSIS_PADS_NUM 2 |
| |
| #define MIPI_CSIS_DEF_PIX_WIDTH 640 |
| #define MIPI_CSIS_DEF_PIX_HEIGHT 480 |
| |
| /* Register map definition */ |
| |
| /* CSIS version */ |
| #define MIPI_CSIS_VERSION 0x00 |
| #define MIPI_CSIS_VERSION_IMX7D 0x03030505 |
| #define MIPI_CSIS_VERSION_IMX8MP 0x03060301 |
| |
| /* CSIS common control */ |
| #define MIPI_CSIS_CMN_CTRL 0x04 |
| #define MIPI_CSIS_CMN_CTRL_UPDATE_SHADOW BIT(16) |
| #define MIPI_CSIS_CMN_CTRL_INTER_MODE BIT(10) |
| #define MIPI_CSIS_CMN_CTRL_UPDATE_SHADOW_CTRL BIT(2) |
| #define MIPI_CSIS_CMN_CTRL_RESET BIT(1) |
| #define MIPI_CSIS_CMN_CTRL_ENABLE BIT(0) |
| |
| #define MIPI_CSIS_CMN_CTRL_LANE_NR_OFFSET 8 |
| #define MIPI_CSIS_CMN_CTRL_LANE_NR_MASK (3 << 8) |
| |
| /* CSIS clock control */ |
| #define MIPI_CSIS_CLK_CTRL 0x08 |
| #define MIPI_CSIS_CLK_CTRL_CLKGATE_TRAIL_CH3(x) ((x) << 28) |
| #define MIPI_CSIS_CLK_CTRL_CLKGATE_TRAIL_CH2(x) ((x) << 24) |
| #define MIPI_CSIS_CLK_CTRL_CLKGATE_TRAIL_CH1(x) ((x) << 20) |
| #define MIPI_CSIS_CLK_CTRL_CLKGATE_TRAIL_CH0(x) ((x) << 16) |
| #define MIPI_CSIS_CLK_CTRL_CLKGATE_EN_MSK (0xf << 4) |
| #define MIPI_CSIS_CLK_CTRL_WCLK_SRC BIT(0) |
| |
| /* CSIS Interrupt mask */ |
| #define MIPI_CSIS_INT_MSK 0x10 |
| #define MIPI_CSIS_INT_MSK_EVEN_BEFORE BIT(31) |
| #define MIPI_CSIS_INT_MSK_EVEN_AFTER BIT(30) |
| #define MIPI_CSIS_INT_MSK_ODD_BEFORE BIT(29) |
| #define MIPI_CSIS_INT_MSK_ODD_AFTER BIT(28) |
| #define MIPI_CSIS_INT_MSK_FRAME_START BIT(24) |
| #define MIPI_CSIS_INT_MSK_FRAME_END BIT(20) |
| #define MIPI_CSIS_INT_MSK_ERR_SOT_HS BIT(16) |
| #define MIPI_CSIS_INT_MSK_ERR_LOST_FS BIT(12) |
| #define MIPI_CSIS_INT_MSK_ERR_LOST_FE BIT(8) |
| #define MIPI_CSIS_INT_MSK_ERR_OVER BIT(4) |
| #define MIPI_CSIS_INT_MSK_ERR_WRONG_CFG BIT(3) |
| #define MIPI_CSIS_INT_MSK_ERR_ECC BIT(2) |
| #define MIPI_CSIS_INT_MSK_ERR_CRC BIT(1) |
| #define MIPI_CSIS_INT_MSK_ERR_UNKNOWN BIT(0) |
| |
| /* CSIS Interrupt source */ |
| #define MIPI_CSIS_INT_SRC 0x14 |
| #define MIPI_CSIS_INT_SRC_EVEN_BEFORE BIT(31) |
| #define MIPI_CSIS_INT_SRC_EVEN_AFTER BIT(30) |
| #define MIPI_CSIS_INT_SRC_EVEN BIT(30) |
| #define MIPI_CSIS_INT_SRC_ODD_BEFORE BIT(29) |
| #define MIPI_CSIS_INT_SRC_ODD_AFTER BIT(28) |
| #define MIPI_CSIS_INT_SRC_ODD (0x3 << 28) |
| #define MIPI_CSIS_INT_SRC_NON_IMAGE_DATA (0xf << 28) |
| #define MIPI_CSIS_INT_SRC_FRAME_START BIT(24) |
| #define MIPI_CSIS_INT_SRC_FRAME_END BIT(20) |
| #define MIPI_CSIS_INT_SRC_ERR_SOT_HS BIT(16) |
| #define MIPI_CSIS_INT_SRC_ERR_LOST_FS BIT(12) |
| #define MIPI_CSIS_INT_SRC_ERR_LOST_FE BIT(8) |
| #define MIPI_CSIS_INT_SRC_ERR_OVER BIT(4) |
| #define MIPI_CSIS_INT_SRC_ERR_WRONG_CFG BIT(3) |
| #define MIPI_CSIS_INT_SRC_ERR_ECC BIT(2) |
| #define MIPI_CSIS_INT_SRC_ERR_CRC BIT(1) |
| #define MIPI_CSIS_INT_SRC_ERR_UNKNOWN BIT(0) |
| #define MIPI_CSIS_INT_SRC_ERRORS 0xfffff |
| |
| /* D-PHY status control */ |
| #define MIPI_CSIS_DPHY_STATUS 0x20 |
| #define MIPI_CSIS_DPHY_STATUS_ULPS_DAT BIT(8) |
| #define MIPI_CSIS_DPHY_STATUS_STOPSTATE_DAT BIT(4) |
| #define MIPI_CSIS_DPHY_STATUS_ULPS_CLK BIT(1) |
| #define MIPI_CSIS_DPHY_STATUS_STOPSTATE_CLK BIT(0) |
| |
| /* D-PHY common control */ |
| #define MIPI_CSIS_DPHY_CMN_CTRL 0x24 |
| #define MIPI_CSIS_DPHY_CMN_CTRL_HSSETTLE(n) ((n) << 24) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_HSSETTLE_MASK GENMASK(31, 24) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_CLKSETTLE(n) ((n) << 22) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_CLKSETTLE_MASK GENMASK(23, 22) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_DPDN_SWAP_CLK BIT(6) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_DPDN_SWAP_DAT BIT(5) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_ENABLE_DAT BIT(1) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_ENABLE_CLK BIT(0) |
| #define MIPI_CSIS_DPHY_CMN_CTRL_ENABLE (0x1f << 0) |
| |
| /* D-PHY Master and Slave Control register Low */ |
| #define MIPI_CSIS_DPHY_BCTRL_L 0x30 |
| #define MIPI_CSIS_DPHY_BCTRL_L_USER_DATA_PATTERN_LOW(n) (((n) & 3U) << 30) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BIAS_REF_VOLT_715MV (0 << 28) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BIAS_REF_VOLT_724MV (1 << 28) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BIAS_REF_VOLT_733MV (2 << 28) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BIAS_REF_VOLT_706MV (3 << 28) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BGR_CHOPPER_FREQ_3MHZ (0 << 27) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BGR_CHOPPER_FREQ_1_5MHZ (1 << 27) |
| #define MIPI_CSIS_DPHY_BCTRL_L_VREG12_EXTPWR_EN_CTL BIT(26) |
| #define MIPI_CSIS_DPHY_BCTRL_L_REG_12P_LVL_CTL_1_2V (0 << 24) |
| #define MIPI_CSIS_DPHY_BCTRL_L_REG_12P_LVL_CTL_1_23V (1 << 24) |
| #define MIPI_CSIS_DPHY_BCTRL_L_REG_12P_LVL_CTL_1_17V (2 << 24) |
| #define MIPI_CSIS_DPHY_BCTRL_L_REG_12P_LVL_CTL_1_26V (3 << 24) |
| #define MIPI_CSIS_DPHY_BCTRL_L_REG_1P2_LVL_SEL BIT(23) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_HYS_LVL_80MV (0 << 21) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_HYS_LVL_100MV (1 << 21) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_HYS_LVL_120MV (2 << 21) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_HYS_LVL_140MV (3 << 21) |
| #define MIPI_CSIS_DPHY_BCTRL_L_VREF_SRC_SEL BIT(20) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_VREF_LVL_715MV (0 << 18) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_VREF_LVL_743MV (1 << 18) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_VREF_LVL_650MV (2 << 18) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_VREF_LVL_682MV (3 << 18) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_RX_PULSE_REJECT BIT(17) |
| #define MIPI_CSIS_DPHY_BCTRL_L_MSTRCLK_LP_SLEW_RATE_DOWN_0 (0 << 15) |
| #define MIPI_CSIS_DPHY_BCTRL_L_MSTRCLK_LP_SLEW_RATE_DOWN_15P (1 << 15) |
| #define MIPI_CSIS_DPHY_BCTRL_L_MSTRCLK_LP_SLEW_RATE_DOWN_30P (3 << 15) |
| #define MIPI_CSIS_DPHY_BCTRL_L_MSTRCLK_LP_SLEW_RATE_UP BIT(14) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_CD_HYS_60MV (0 << 13) |
| #define MIPI_CSIS_DPHY_BCTRL_L_LP_CD_HYS_70MV (1 << 13) |
| #define MIPI_CSIS_DPHY_BCTRL_L_BGR_CHOPPER_EN BIT(12) |
| #define MIPI_CSIS_DPHY_BCTRL_L_ERRCONTENTION_LP_EN BIT(11) |
| #define MIPI_CSIS_DPHY_BCTRL_L_TXTRIGGER_CLK_EN BIT(10) |
| #define MIPI_CSIS_DPHY_BCTRL_L_B_DPHYCTRL(n) (((n) * 25 / 1000000) << 0) |
| |
| /* D-PHY Master and Slave Control register High */ |
| #define MIPI_CSIS_DPHY_BCTRL_H 0x34 |
| /* D-PHY Slave Control register Low */ |
| #define MIPI_CSIS_DPHY_SCTRL_L 0x38 |
| /* D-PHY Slave Control register High */ |
| #define MIPI_CSIS_DPHY_SCTRL_H 0x3c |
| |
| /* ISP Configuration register */ |
| #define MIPI_CSIS_ISP_CONFIG_CH(n) (0x40 + (n) * 0x10) |
| #define MIPI_CSIS_ISPCFG_MEM_FULL_GAP_MSK (0xff << 24) |
| #define MIPI_CSIS_ISPCFG_MEM_FULL_GAP(x) ((x) << 24) |
| #define MIPI_CSIS_ISPCFG_PIXEL_MODE_SINGLE (0 << 12) |
| #define MIPI_CSIS_ISPCFG_PIXEL_MODE_DUAL (1 << 12) |
| #define MIPI_CSIS_ISPCFG_PIXEL_MODE_QUAD (2 << 12) /* i.MX8M[MNP] only */ |
| #define MIPI_CSIS_ISPCFG_PIXEL_MASK (3 << 12) |
| #define MIPI_CSIS_ISPCFG_ALIGN_32BIT BIT(11) |
| #define MIPI_CSIS_ISPCFG_FMT(fmt) ((fmt) << 2) |
| #define MIPI_CSIS_ISPCFG_FMT_MASK (0x3f << 2) |
| |
| /* ISP Image Resolution register */ |
| #define MIPI_CSIS_ISP_RESOL_CH(n) (0x44 + (n) * 0x10) |
| #define CSIS_MAX_PIX_WIDTH 0xffff |
| #define CSIS_MAX_PIX_HEIGHT 0xffff |
| |
| /* ISP SYNC register */ |
| #define MIPI_CSIS_ISP_SYNC_CH(n) (0x48 + (n) * 0x10) |
| #define MIPI_CSIS_ISP_SYNC_HSYNC_LINTV_OFFSET 18 |
| #define MIPI_CSIS_ISP_SYNC_VSYNC_SINTV_OFFSET 12 |
| #define MIPI_CSIS_ISP_SYNC_VSYNC_EINTV_OFFSET 0 |
| |
| /* ISP shadow registers */ |
| #define MIPI_CSIS_SDW_CONFIG_CH(n) (0x80 + (n) * 0x10) |
| #define MIPI_CSIS_SDW_RESOL_CH(n) (0x84 + (n) * 0x10) |
| #define MIPI_CSIS_SDW_SYNC_CH(n) (0x88 + (n) * 0x10) |
| |
| /* Debug control register */ |
| #define MIPI_CSIS_DBG_CTRL 0xc0 |
| #define MIPI_CSIS_DBG_INTR_MSK 0xc4 |
| #define MIPI_CSIS_DBG_INTR_MSK_DT_NOT_SUPPORT BIT(25) |
| #define MIPI_CSIS_DBG_INTR_MSK_DT_IGNORE BIT(24) |
| #define MIPI_CSIS_DBG_INTR_MSK_ERR_FRAME_SIZE BIT(20) |
| #define MIPI_CSIS_DBG_INTR_MSK_TRUNCATED_FRAME BIT(16) |
| #define MIPI_CSIS_DBG_INTR_MSK_EARLY_FE BIT(12) |
| #define MIPI_CSIS_DBG_INTR_MSK_EARLY_FS BIT(8) |
| #define MIPI_CSIS_DBG_INTR_MSK_CAM_VSYNC_FALL BIT(4) |
| #define MIPI_CSIS_DBG_INTR_MSK_CAM_VSYNC_RISE BIT(0) |
| #define MIPI_CSIS_DBG_INTR_SRC 0xc8 |
| #define MIPI_CSIS_DBG_INTR_SRC_DT_NOT_SUPPORT BIT(25) |
| #define MIPI_CSIS_DBG_INTR_SRC_DT_IGNORE BIT(24) |
| #define MIPI_CSIS_DBG_INTR_SRC_ERR_FRAME_SIZE BIT(20) |
| #define MIPI_CSIS_DBG_INTR_SRC_TRUNCATED_FRAME BIT(16) |
| #define MIPI_CSIS_DBG_INTR_SRC_EARLY_FE BIT(12) |
| #define MIPI_CSIS_DBG_INTR_SRC_EARLY_FS BIT(8) |
| #define MIPI_CSIS_DBG_INTR_SRC_CAM_VSYNC_FALL BIT(4) |
| #define MIPI_CSIS_DBG_INTR_SRC_CAM_VSYNC_RISE BIT(0) |
| |
| #define MIPI_CSIS_FRAME_COUNTER_CH(n) (0x0100 + (n) * 4) |
| |
| /* Non-image packet data buffers */ |
| #define MIPI_CSIS_PKTDATA_ODD 0x2000 |
| #define MIPI_CSIS_PKTDATA_EVEN 0x3000 |
| #define MIPI_CSIS_PKTDATA_SIZE SZ_4K |
| |
| #define DEFAULT_SCLK_CSIS_FREQ 166000000UL |
| |
| /* MIPI CSI-2 Data Types */ |
| #define MIPI_CSI2_DATA_TYPE_YUV420_8 0x18 |
| #define MIPI_CSI2_DATA_TYPE_YUV420_10 0x19 |
| #define MIPI_CSI2_DATA_TYPE_LE_YUV420_8 0x1a |
| #define MIPI_CSI2_DATA_TYPE_CS_YUV420_8 0x1c |
| #define MIPI_CSI2_DATA_TYPE_CS_YUV420_10 0x1d |
| #define MIPI_CSI2_DATA_TYPE_YUV422_8 0x1e |
| #define MIPI_CSI2_DATA_TYPE_YUV422_10 0x1f |
| #define MIPI_CSI2_DATA_TYPE_RGB565 0x22 |
| #define MIPI_CSI2_DATA_TYPE_RGB666 0x23 |
| #define MIPI_CSI2_DATA_TYPE_RGB888 0x24 |
| #define MIPI_CSI2_DATA_TYPE_RAW6 0x28 |
| #define MIPI_CSI2_DATA_TYPE_RAW7 0x29 |
| #define MIPI_CSI2_DATA_TYPE_RAW8 0x2a |
| #define MIPI_CSI2_DATA_TYPE_RAW10 0x2b |
| #define MIPI_CSI2_DATA_TYPE_RAW12 0x2c |
| #define MIPI_CSI2_DATA_TYPE_RAW14 0x2d |
| #define MIPI_CSI2_DATA_TYPE_USER(x) (0x30 + (x)) |
| |
| struct mipi_csis_event { |
| bool debug; |
| u32 mask; |
| const char * const name; |
| unsigned int counter; |
| }; |
| |
| static const struct mipi_csis_event mipi_csis_events[] = { |
| /* Errors */ |
| { false, MIPI_CSIS_INT_SRC_ERR_SOT_HS, "SOT Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_LOST_FS, "Lost Frame Start Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_LOST_FE, "Lost Frame End Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_OVER, "FIFO Overflow Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_WRONG_CFG, "Wrong Configuration Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_ECC, "ECC Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_CRC, "CRC Error" }, |
| { false, MIPI_CSIS_INT_SRC_ERR_UNKNOWN, "Unknown Error" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_DT_NOT_SUPPORT, "Data Type Not Supported" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_DT_IGNORE, "Data Type Ignored" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_ERR_FRAME_SIZE, "Frame Size Error" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_TRUNCATED_FRAME, "Truncated Frame" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_EARLY_FE, "Early Frame End" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_EARLY_FS, "Early Frame Start" }, |
| /* Non-image data receive events */ |
| { false, MIPI_CSIS_INT_SRC_EVEN_BEFORE, "Non-image data before even frame" }, |
| { false, MIPI_CSIS_INT_SRC_EVEN_AFTER, "Non-image data after even frame" }, |
| { false, MIPI_CSIS_INT_SRC_ODD_BEFORE, "Non-image data before odd frame" }, |
| { false, MIPI_CSIS_INT_SRC_ODD_AFTER, "Non-image data after odd frame" }, |
| /* Frame start/end */ |
| { false, MIPI_CSIS_INT_SRC_FRAME_START, "Frame Start" }, |
| { false, MIPI_CSIS_INT_SRC_FRAME_END, "Frame End" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_CAM_VSYNC_FALL, "VSYNC Falling Edge" }, |
| { true, MIPI_CSIS_DBG_INTR_SRC_CAM_VSYNC_RISE, "VSYNC Rising Edge" }, |
| }; |
| |
| #define MIPI_CSIS_NUM_EVENTS ARRAY_SIZE(mipi_csis_events) |
| |
| enum mipi_csis_clk { |
| MIPI_CSIS_CLK_PCLK, |
| MIPI_CSIS_CLK_WRAP, |
| MIPI_CSIS_CLK_PHY, |
| MIPI_CSIS_CLK_AXI, |
| }; |
| |
| static const char * const mipi_csis_clk_id[] = { |
| "pclk", |
| "wrap", |
| "phy", |
| "axi", |
| }; |
| |
| enum mipi_csis_version { |
| MIPI_CSIS_V3_3, |
| MIPI_CSIS_V3_6_3, |
| }; |
| |
| struct mipi_csis_info { |
| enum mipi_csis_version version; |
| unsigned int num_clocks; |
| }; |
| |
| struct mipi_csis_device { |
| struct device *dev; |
| void __iomem *regs; |
| struct clk_bulk_data *clks; |
| struct reset_control *mrst; |
| struct regulator *mipi_phy_regulator; |
| const struct mipi_csis_info *info; |
| |
| struct v4l2_subdev sd; |
| struct media_pad pads[CSIS_PADS_NUM]; |
| struct v4l2_async_notifier notifier; |
| struct v4l2_subdev *src_sd; |
| |
| struct v4l2_mbus_config_mipi_csi2 bus; |
| u32 clk_frequency; |
| u32 hs_settle; |
| u32 clk_settle; |
| |
| spinlock_t slock; /* Protect events */ |
| struct mipi_csis_event events[MIPI_CSIS_NUM_EVENTS]; |
| struct dentry *debugfs_root; |
| struct { |
| bool enable; |
| u32 hs_settle; |
| u32 clk_settle; |
| } debug; |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * Format helpers |
| */ |
| |
| struct csis_pix_format { |
| u32 code; |
| u32 output; |
| u32 data_type; |
| u8 width; |
| }; |
| |
| static const struct csis_pix_format mipi_csis_formats[] = { |
| /* YUV formats. */ |
| { |
| .code = MEDIA_BUS_FMT_UYVY8_1X16, |
| .output = MEDIA_BUS_FMT_UYVY8_1X16, |
| .data_type = MIPI_CSI2_DATA_TYPE_YUV422_8, |
| .width = 16, |
| }, |
| /* RGB formats. */ |
| { |
| .code = MEDIA_BUS_FMT_RGB565_1X16, |
| .output = MEDIA_BUS_FMT_RGB565_1X16, |
| .data_type = MIPI_CSI2_DATA_TYPE_RGB565, |
| .width = 16, |
| }, { |
| .code = MEDIA_BUS_FMT_BGR888_1X24, |
| .output = MEDIA_BUS_FMT_RGB888_1X24, |
| .data_type = MIPI_CSI2_DATA_TYPE_RGB888, |
| .width = 24, |
| }, |
| /* RAW (Bayer and greyscale) formats. */ |
| { |
| .code = MEDIA_BUS_FMT_SBGGR8_1X8, |
| .output = MEDIA_BUS_FMT_SBGGR8_1X8, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| }, { |
| .code = MEDIA_BUS_FMT_SGBRG8_1X8, |
| .output = MEDIA_BUS_FMT_SGBRG8_1X8, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| }, { |
| .code = MEDIA_BUS_FMT_SGRBG8_1X8, |
| .output = MEDIA_BUS_FMT_SGRBG8_1X8, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| }, { |
| .code = MEDIA_BUS_FMT_SRGGB8_1X8, |
| .output = MEDIA_BUS_FMT_SRGGB8_1X8, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| }, { |
| .code = MEDIA_BUS_FMT_Y8_1X8, |
| .output = MEDIA_BUS_FMT_Y8_1X8, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| }, { |
| .code = MEDIA_BUS_FMT_SBGGR10_1X10, |
| .output = MEDIA_BUS_FMT_SBGGR10_1X10, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW10, |
| .width = 10, |
| }, { |
| .code = MEDIA_BUS_FMT_SGBRG10_1X10, |
| .output = MEDIA_BUS_FMT_SGBRG10_1X10, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW10, |
| .width = 10, |
| }, { |
| .code = MEDIA_BUS_FMT_SGRBG10_1X10, |
| .output = MEDIA_BUS_FMT_SGRBG10_1X10, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW10, |
| .width = 10, |
| }, { |
| .code = MEDIA_BUS_FMT_SRGGB10_1X10, |
| .output = MEDIA_BUS_FMT_SRGGB10_1X10, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW10, |
| .width = 10, |
| }, { |
| .code = MEDIA_BUS_FMT_Y10_1X10, |
| .output = MEDIA_BUS_FMT_Y10_1X10, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW10, |
| .width = 10, |
| }, { |
| .code = MEDIA_BUS_FMT_SBGGR12_1X12, |
| .output = MEDIA_BUS_FMT_SBGGR12_1X12, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW12, |
| .width = 12, |
| }, { |
| .code = MEDIA_BUS_FMT_SGBRG12_1X12, |
| .output = MEDIA_BUS_FMT_SGBRG12_1X12, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW12, |
| .width = 12, |
| }, { |
| .code = MEDIA_BUS_FMT_SGRBG12_1X12, |
| .output = MEDIA_BUS_FMT_SGRBG12_1X12, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW12, |
| .width = 12, |
| }, { |
| .code = MEDIA_BUS_FMT_SRGGB12_1X12, |
| .output = MEDIA_BUS_FMT_SRGGB12_1X12, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW12, |
| .width = 12, |
| }, { |
| .code = MEDIA_BUS_FMT_Y12_1X12, |
| .output = MEDIA_BUS_FMT_Y12_1X12, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW12, |
| .width = 12, |
| }, { |
| .code = MEDIA_BUS_FMT_SBGGR14_1X14, |
| .output = MEDIA_BUS_FMT_SBGGR14_1X14, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW14, |
| .width = 14, |
| }, { |
| .code = MEDIA_BUS_FMT_SGBRG14_1X14, |
| .output = MEDIA_BUS_FMT_SGBRG14_1X14, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW14, |
| .width = 14, |
| }, { |
| .code = MEDIA_BUS_FMT_SGRBG14_1X14, |
| .output = MEDIA_BUS_FMT_SGRBG14_1X14, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW14, |
| .width = 14, |
| }, { |
| .code = MEDIA_BUS_FMT_SRGGB14_1X14, |
| .output = MEDIA_BUS_FMT_SRGGB14_1X14, |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW14, |
| .width = 14, |
| }, |
| /* JPEG */ |
| { |
| .code = MEDIA_BUS_FMT_JPEG_1X8, |
| .output = MEDIA_BUS_FMT_JPEG_1X8, |
| /* |
| * Map JPEG_1X8 to the RAW8 datatype. |
| * |
| * The CSI-2 specification suggests in Annex A "JPEG8 Data |
| * Format (informative)" to transmit JPEG data using one of the |
| * Data Types aimed to represent arbitrary data, such as the |
| * "User Defined Data Type 1" (0x30). |
| * |
| * However, when configured with a User Defined Data Type, the |
| * CSIS outputs data in quad pixel mode regardless of the mode |
| * selected in the MIPI_CSIS_ISP_CONFIG_CH register. Neither of |
| * the IP cores connected to the CSIS in i.MX SoCs (CSI bridge |
| * or ISI) support quad pixel mode, so this will never work in |
| * practice. |
| * |
| * Some sensors (such as the OV5640) send JPEG data using the |
| * RAW8 data type. This is usable and works, so map the JPEG |
| * format to RAW8. If the CSIS ends up being integrated in an |
| * SoC that can support quad pixel mode, this will have to be |
| * revisited. |
| */ |
| .data_type = MIPI_CSI2_DATA_TYPE_RAW8, |
| .width = 8, |
| } |
| }; |
| |
| static const struct csis_pix_format *find_csis_format(u32 code) |
| { |
| unsigned int i; |
| |
| for (i = 0; i < ARRAY_SIZE(mipi_csis_formats); i++) |
| if (code == mipi_csis_formats[i].code) |
| return &mipi_csis_formats[i]; |
| return NULL; |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Hardware configuration |
| */ |
| |
| static inline u32 mipi_csis_read(struct mipi_csis_device *csis, u32 reg) |
| { |
| return readl(csis->regs + reg); |
| } |
| |
| static inline void mipi_csis_write(struct mipi_csis_device *csis, u32 reg, |
| u32 val) |
| { |
| writel(val, csis->regs + reg); |
| } |
| |
| static void mipi_csis_enable_interrupts(struct mipi_csis_device *csis, bool on) |
| { |
| mipi_csis_write(csis, MIPI_CSIS_INT_MSK, on ? 0xffffffff : 0); |
| mipi_csis_write(csis, MIPI_CSIS_DBG_INTR_MSK, on ? 0xffffffff : 0); |
| } |
| |
| static void mipi_csis_sw_reset(struct mipi_csis_device *csis) |
| { |
| u32 val = mipi_csis_read(csis, MIPI_CSIS_CMN_CTRL); |
| |
| mipi_csis_write(csis, MIPI_CSIS_CMN_CTRL, |
| val | MIPI_CSIS_CMN_CTRL_RESET); |
| usleep_range(10, 20); |
| } |
| |
| static void mipi_csis_system_enable(struct mipi_csis_device *csis, int on) |
| { |
| u32 val, mask; |
| |
| val = mipi_csis_read(csis, MIPI_CSIS_CMN_CTRL); |
| if (on) |
| val |= MIPI_CSIS_CMN_CTRL_ENABLE; |
| else |
| val &= ~MIPI_CSIS_CMN_CTRL_ENABLE; |
| mipi_csis_write(csis, MIPI_CSIS_CMN_CTRL, val); |
| |
| val = mipi_csis_read(csis, MIPI_CSIS_DPHY_CMN_CTRL); |
| val &= ~MIPI_CSIS_DPHY_CMN_CTRL_ENABLE; |
| if (on) { |
| mask = (1 << (csis->bus.num_data_lanes + 1)) - 1; |
| val |= (mask & MIPI_CSIS_DPHY_CMN_CTRL_ENABLE); |
| } |
| mipi_csis_write(csis, MIPI_CSIS_DPHY_CMN_CTRL, val); |
| } |
| |
| static void __mipi_csis_set_format(struct mipi_csis_device *csis, |
| const struct v4l2_mbus_framefmt *format, |
| const struct csis_pix_format *csis_fmt) |
| { |
| u32 val; |
| |
| /* Color format */ |
| val = mipi_csis_read(csis, MIPI_CSIS_ISP_CONFIG_CH(0)); |
| val &= ~(MIPI_CSIS_ISPCFG_ALIGN_32BIT | MIPI_CSIS_ISPCFG_FMT_MASK |
| | MIPI_CSIS_ISPCFG_PIXEL_MASK); |
| |
| /* |
| * YUV 4:2:2 can be transferred with 8 or 16 bits per clock sample |
| * (referred to in the documentation as single and dual pixel modes |
| * respectively, although the 8-bit mode transfers half a pixel per |
| * clock sample and the 16-bit mode one pixel). While both mode work |
| * when the CSIS is connected to a receiver that supports either option, |
| * single pixel mode requires clock rates twice as high. As all SoCs |
| * that integrate the CSIS can operate in 16-bit bit mode, and some do |
| * not support 8-bit mode (this is the case of the i.MX8MP), use dual |
| * pixel mode unconditionally. |
| * |
| * TODO: Verify which other formats require DUAL (or QUAD) modes. |
| */ |
| if (csis_fmt->data_type == MIPI_CSI2_DATA_TYPE_YUV422_8) |
| val |= MIPI_CSIS_ISPCFG_PIXEL_MODE_DUAL; |
| |
| val |= MIPI_CSIS_ISPCFG_FMT(csis_fmt->data_type); |
| mipi_csis_write(csis, MIPI_CSIS_ISP_CONFIG_CH(0), val); |
| |
| /* Pixel resolution */ |
| val = format->width | (format->height << 16); |
| mipi_csis_write(csis, MIPI_CSIS_ISP_RESOL_CH(0), val); |
| } |
| |
| static int mipi_csis_calculate_params(struct mipi_csis_device *csis, |
| const struct csis_pix_format *csis_fmt) |
| { |
| s64 link_freq; |
| u32 lane_rate; |
| |
| /* Calculate the line rate from the pixel rate. */ |
| link_freq = v4l2_get_link_freq(csis->src_sd->ctrl_handler, |
| csis_fmt->width, |
| csis->bus.num_data_lanes * 2); |
| if (link_freq < 0) { |
| dev_err(csis->dev, "Unable to obtain link frequency: %d\n", |
| (int)link_freq); |
| return link_freq; |
| } |
| |
| lane_rate = link_freq * 2; |
| |
| if (lane_rate < 80000000 || lane_rate > 1500000000) { |
| dev_dbg(csis->dev, "Out-of-bound lane rate %u\n", lane_rate); |
| return -EINVAL; |
| } |
| |
| /* |
| * The HSSETTLE counter value is document in a table, but can also |
| * easily be calculated. Hardcode the CLKSETTLE value to 0 for now |
| * (which is documented as corresponding to CSI-2 v0.87 to v1.00) until |
| * we figure out how to compute it correctly. |
| */ |
| csis->hs_settle = (lane_rate - 5000000) / 45000000; |
| csis->clk_settle = 0; |
| |
| dev_dbg(csis->dev, "lane rate %u, Tclk_settle %u, Ths_settle %u\n", |
| lane_rate, csis->clk_settle, csis->hs_settle); |
| |
| if (csis->debug.hs_settle < 0xff) { |
| dev_dbg(csis->dev, "overriding Ths_settle with %u\n", |
| csis->debug.hs_settle); |
| csis->hs_settle = csis->debug.hs_settle; |
| } |
| |
| if (csis->debug.clk_settle < 4) { |
| dev_dbg(csis->dev, "overriding Tclk_settle with %u\n", |
| csis->debug.clk_settle); |
| csis->clk_settle = csis->debug.clk_settle; |
| } |
| |
| return 0; |
| } |
| |
| static void mipi_csis_set_params(struct mipi_csis_device *csis, |
| const struct v4l2_mbus_framefmt *format, |
| const struct csis_pix_format *csis_fmt) |
| { |
| int lanes = csis->bus.num_data_lanes; |
| u32 val; |
| |
| val = mipi_csis_read(csis, MIPI_CSIS_CMN_CTRL); |
| val &= ~MIPI_CSIS_CMN_CTRL_LANE_NR_MASK; |
| val |= (lanes - 1) << MIPI_CSIS_CMN_CTRL_LANE_NR_OFFSET; |
| if (csis->info->version == MIPI_CSIS_V3_3) |
| val |= MIPI_CSIS_CMN_CTRL_INTER_MODE; |
| mipi_csis_write(csis, MIPI_CSIS_CMN_CTRL, val); |
| |
| __mipi_csis_set_format(csis, format, csis_fmt); |
| |
| mipi_csis_write(csis, MIPI_CSIS_DPHY_CMN_CTRL, |
| MIPI_CSIS_DPHY_CMN_CTRL_HSSETTLE(csis->hs_settle) | |
| MIPI_CSIS_DPHY_CMN_CTRL_CLKSETTLE(csis->clk_settle)); |
| |
| val = (0 << MIPI_CSIS_ISP_SYNC_HSYNC_LINTV_OFFSET) |
| | (0 << MIPI_CSIS_ISP_SYNC_VSYNC_SINTV_OFFSET) |
| | (0 << MIPI_CSIS_ISP_SYNC_VSYNC_EINTV_OFFSET); |
| mipi_csis_write(csis, MIPI_CSIS_ISP_SYNC_CH(0), val); |
| |
| val = mipi_csis_read(csis, MIPI_CSIS_CLK_CTRL); |
| val |= MIPI_CSIS_CLK_CTRL_WCLK_SRC; |
| val |= MIPI_CSIS_CLK_CTRL_CLKGATE_TRAIL_CH0(15); |
| val &= ~MIPI_CSIS_CLK_CTRL_CLKGATE_EN_MSK; |
| mipi_csis_write(csis, MIPI_CSIS_CLK_CTRL, val); |
| |
| mipi_csis_write(csis, MIPI_CSIS_DPHY_BCTRL_L, |
| MIPI_CSIS_DPHY_BCTRL_L_BIAS_REF_VOLT_715MV | |
| MIPI_CSIS_DPHY_BCTRL_L_BGR_CHOPPER_FREQ_3MHZ | |
| MIPI_CSIS_DPHY_BCTRL_L_REG_12P_LVL_CTL_1_2V | |
| MIPI_CSIS_DPHY_BCTRL_L_LP_RX_HYS_LVL_80MV | |
| MIPI_CSIS_DPHY_BCTRL_L_LP_RX_VREF_LVL_715MV | |
| MIPI_CSIS_DPHY_BCTRL_L_LP_CD_HYS_60MV | |
| MIPI_CSIS_DPHY_BCTRL_L_B_DPHYCTRL(20000000)); |
| mipi_csis_write(csis, MIPI_CSIS_DPHY_BCTRL_H, 0); |
| |
| /* Update the shadow register. */ |
| val = mipi_csis_read(csis, MIPI_CSIS_CMN_CTRL); |
| mipi_csis_write(csis, MIPI_CSIS_CMN_CTRL, |
| val | MIPI_CSIS_CMN_CTRL_UPDATE_SHADOW | |
| MIPI_CSIS_CMN_CTRL_UPDATE_SHADOW_CTRL); |
| } |
| |
| static int mipi_csis_clk_enable(struct mipi_csis_device *csis) |
| { |
| return clk_bulk_prepare_enable(csis->info->num_clocks, csis->clks); |
| } |
| |
| static void mipi_csis_clk_disable(struct mipi_csis_device *csis) |
| { |
| clk_bulk_disable_unprepare(csis->info->num_clocks, csis->clks); |
| } |
| |
| static int mipi_csis_clk_get(struct mipi_csis_device *csis) |
| { |
| unsigned int i; |
| int ret; |
| |
| csis->clks = devm_kcalloc(csis->dev, csis->info->num_clocks, |
| sizeof(*csis->clks), GFP_KERNEL); |
| |
| if (!csis->clks) |
| return -ENOMEM; |
| |
| for (i = 0; i < csis->info->num_clocks; i++) |
| csis->clks[i].id = mipi_csis_clk_id[i]; |
| |
| ret = devm_clk_bulk_get(csis->dev, csis->info->num_clocks, |
| csis->clks); |
| if (ret < 0) |
| return ret; |
| |
| /* Set clock rate */ |
| ret = clk_set_rate(csis->clks[MIPI_CSIS_CLK_WRAP].clk, |
| csis->clk_frequency); |
| if (ret < 0) |
| dev_err(csis->dev, "set rate=%d failed: %d\n", |
| csis->clk_frequency, ret); |
| |
| return ret; |
| } |
| |
| static void mipi_csis_start_stream(struct mipi_csis_device *csis, |
| const struct v4l2_mbus_framefmt *format, |
| const struct csis_pix_format *csis_fmt) |
| { |
| mipi_csis_sw_reset(csis); |
| mipi_csis_set_params(csis, format, csis_fmt); |
| mipi_csis_system_enable(csis, true); |
| mipi_csis_enable_interrupts(csis, true); |
| } |
| |
| static void mipi_csis_stop_stream(struct mipi_csis_device *csis) |
| { |
| mipi_csis_enable_interrupts(csis, false); |
| mipi_csis_system_enable(csis, false); |
| } |
| |
| static irqreturn_t mipi_csis_irq_handler(int irq, void *dev_id) |
| { |
| struct mipi_csis_device *csis = dev_id; |
| unsigned long flags; |
| unsigned int i; |
| u32 status; |
| u32 dbg_status; |
| |
| status = mipi_csis_read(csis, MIPI_CSIS_INT_SRC); |
| dbg_status = mipi_csis_read(csis, MIPI_CSIS_DBG_INTR_SRC); |
| |
| spin_lock_irqsave(&csis->slock, flags); |
| |
| /* Update the event/error counters */ |
| if ((status & MIPI_CSIS_INT_SRC_ERRORS) || csis->debug.enable) { |
| for (i = 0; i < MIPI_CSIS_NUM_EVENTS; i++) { |
| struct mipi_csis_event *event = &csis->events[i]; |
| |
| if ((!event->debug && (status & event->mask)) || |
| (event->debug && (dbg_status & event->mask))) |
| event->counter++; |
| } |
| } |
| spin_unlock_irqrestore(&csis->slock, flags); |
| |
| mipi_csis_write(csis, MIPI_CSIS_INT_SRC, status); |
| mipi_csis_write(csis, MIPI_CSIS_DBG_INTR_SRC, dbg_status); |
| |
| return IRQ_HANDLED; |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * PHY regulator and reset |
| */ |
| |
| static int mipi_csis_phy_enable(struct mipi_csis_device *csis) |
| { |
| if (csis->info->version != MIPI_CSIS_V3_3) |
| return 0; |
| |
| return regulator_enable(csis->mipi_phy_regulator); |
| } |
| |
| static int mipi_csis_phy_disable(struct mipi_csis_device *csis) |
| { |
| if (csis->info->version != MIPI_CSIS_V3_3) |
| return 0; |
| |
| return regulator_disable(csis->mipi_phy_regulator); |
| } |
| |
| static void mipi_csis_phy_reset(struct mipi_csis_device *csis) |
| { |
| if (csis->info->version != MIPI_CSIS_V3_3) |
| return; |
| |
| reset_control_assert(csis->mrst); |
| msleep(20); |
| reset_control_deassert(csis->mrst); |
| } |
| |
| static int mipi_csis_phy_init(struct mipi_csis_device *csis) |
| { |
| if (csis->info->version != MIPI_CSIS_V3_3) |
| return 0; |
| |
| /* Get MIPI PHY reset and regulator. */ |
| csis->mrst = devm_reset_control_get_exclusive(csis->dev, NULL); |
| if (IS_ERR(csis->mrst)) |
| return PTR_ERR(csis->mrst); |
| |
| csis->mipi_phy_regulator = devm_regulator_get(csis->dev, "phy"); |
| if (IS_ERR(csis->mipi_phy_regulator)) |
| return PTR_ERR(csis->mipi_phy_regulator); |
| |
| return regulator_set_voltage(csis->mipi_phy_regulator, 1000000, |
| 1000000); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Debug |
| */ |
| |
| static void mipi_csis_clear_counters(struct mipi_csis_device *csis) |
| { |
| unsigned long flags; |
| unsigned int i; |
| |
| spin_lock_irqsave(&csis->slock, flags); |
| for (i = 0; i < MIPI_CSIS_NUM_EVENTS; i++) |
| csis->events[i].counter = 0; |
| spin_unlock_irqrestore(&csis->slock, flags); |
| } |
| |
| static void mipi_csis_log_counters(struct mipi_csis_device *csis, bool non_errors) |
| { |
| unsigned int num_events = non_errors ? MIPI_CSIS_NUM_EVENTS |
| : MIPI_CSIS_NUM_EVENTS - 8; |
| unsigned long flags; |
| unsigned int i; |
| |
| spin_lock_irqsave(&csis->slock, flags); |
| |
| for (i = 0; i < num_events; ++i) { |
| if (csis->events[i].counter > 0 || csis->debug.enable) |
| dev_info(csis->dev, "%s events: %d\n", |
| csis->events[i].name, |
| csis->events[i].counter); |
| } |
| spin_unlock_irqrestore(&csis->slock, flags); |
| } |
| |
| static int mipi_csis_dump_regs(struct mipi_csis_device *csis) |
| { |
| static const struct { |
| u32 offset; |
| const char * const name; |
| } registers[] = { |
| { MIPI_CSIS_CMN_CTRL, "CMN_CTRL" }, |
| { MIPI_CSIS_CLK_CTRL, "CLK_CTRL" }, |
| { MIPI_CSIS_INT_MSK, "INT_MSK" }, |
| { MIPI_CSIS_DPHY_STATUS, "DPHY_STATUS" }, |
| { MIPI_CSIS_DPHY_CMN_CTRL, "DPHY_CMN_CTRL" }, |
| { MIPI_CSIS_DPHY_SCTRL_L, "DPHY_SCTRL_L" }, |
| { MIPI_CSIS_DPHY_SCTRL_H, "DPHY_SCTRL_H" }, |
| { MIPI_CSIS_ISP_CONFIG_CH(0), "ISP_CONFIG_CH0" }, |
| { MIPI_CSIS_ISP_RESOL_CH(0), "ISP_RESOL_CH0" }, |
| { MIPI_CSIS_SDW_CONFIG_CH(0), "SDW_CONFIG_CH0" }, |
| { MIPI_CSIS_SDW_RESOL_CH(0), "SDW_RESOL_CH0" }, |
| { MIPI_CSIS_DBG_CTRL, "DBG_CTRL" }, |
| { MIPI_CSIS_FRAME_COUNTER_CH(0), "FRAME_COUNTER_CH0" }, |
| }; |
| |
| unsigned int i; |
| u32 cfg; |
| |
| if (!pm_runtime_get_if_in_use(csis->dev)) |
| return 0; |
| |
| dev_info(csis->dev, "--- REGISTERS ---\n"); |
| |
| for (i = 0; i < ARRAY_SIZE(registers); i++) { |
| cfg = mipi_csis_read(csis, registers[i].offset); |
| dev_info(csis->dev, "%14s: 0x%08x\n", registers[i].name, cfg); |
| } |
| |
| pm_runtime_put(csis->dev); |
| |
| return 0; |
| } |
| |
| static int mipi_csis_dump_regs_show(struct seq_file *m, void *private) |
| { |
| struct mipi_csis_device *csis = m->private; |
| |
| return mipi_csis_dump_regs(csis); |
| } |
| DEFINE_SHOW_ATTRIBUTE(mipi_csis_dump_regs); |
| |
| static void mipi_csis_debugfs_init(struct mipi_csis_device *csis) |
| { |
| csis->debug.hs_settle = UINT_MAX; |
| csis->debug.clk_settle = UINT_MAX; |
| |
| csis->debugfs_root = debugfs_create_dir(dev_name(csis->dev), NULL); |
| |
| debugfs_create_bool("debug_enable", 0600, csis->debugfs_root, |
| &csis->debug.enable); |
| debugfs_create_file("dump_regs", 0600, csis->debugfs_root, csis, |
| &mipi_csis_dump_regs_fops); |
| debugfs_create_u32("tclk_settle", 0600, csis->debugfs_root, |
| &csis->debug.clk_settle); |
| debugfs_create_u32("ths_settle", 0600, csis->debugfs_root, |
| &csis->debug.hs_settle); |
| } |
| |
| static void mipi_csis_debugfs_exit(struct mipi_csis_device *csis) |
| { |
| debugfs_remove_recursive(csis->debugfs_root); |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * V4L2 subdev operations |
| */ |
| |
| static struct mipi_csis_device *sd_to_mipi_csis_device(struct v4l2_subdev *sdev) |
| { |
| return container_of(sdev, struct mipi_csis_device, sd); |
| } |
| |
| static int mipi_csis_s_stream(struct v4l2_subdev *sd, int enable) |
| { |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| const struct v4l2_mbus_framefmt *format; |
| const struct csis_pix_format *csis_fmt; |
| struct v4l2_subdev_state *state; |
| int ret; |
| |
| if (!enable) { |
| v4l2_subdev_call(csis->src_sd, video, s_stream, 0); |
| |
| mipi_csis_stop_stream(csis); |
| if (csis->debug.enable) |
| mipi_csis_log_counters(csis, true); |
| |
| pm_runtime_put(csis->dev); |
| |
| return 0; |
| } |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| |
| format = v4l2_subdev_state_get_format(state, CSIS_PAD_SINK); |
| csis_fmt = find_csis_format(format->code); |
| |
| ret = mipi_csis_calculate_params(csis, csis_fmt); |
| if (ret < 0) |
| goto err_unlock; |
| |
| mipi_csis_clear_counters(csis); |
| |
| ret = pm_runtime_resume_and_get(csis->dev); |
| if (ret < 0) |
| goto err_unlock; |
| |
| mipi_csis_start_stream(csis, format, csis_fmt); |
| |
| ret = v4l2_subdev_call(csis->src_sd, video, s_stream, 1); |
| if (ret < 0) |
| goto err_stop; |
| |
| mipi_csis_log_counters(csis, true); |
| |
| v4l2_subdev_unlock_state(state); |
| |
| return 0; |
| |
| err_stop: |
| mipi_csis_stop_stream(csis); |
| pm_runtime_put(csis->dev); |
| err_unlock: |
| v4l2_subdev_unlock_state(state); |
| |
| return ret; |
| } |
| |
| static int mipi_csis_enum_mbus_code(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_mbus_code_enum *code) |
| { |
| /* |
| * The CSIS can't transcode in any way, the source format is identical |
| * to the sink format. |
| */ |
| if (code->pad == CSIS_PAD_SOURCE) { |
| struct v4l2_mbus_framefmt *fmt; |
| |
| if (code->index > 0) |
| return -EINVAL; |
| |
| fmt = v4l2_subdev_state_get_format(sd_state, code->pad); |
| code->code = fmt->code; |
| return 0; |
| } |
| |
| if (code->pad != CSIS_PAD_SINK) |
| return -EINVAL; |
| |
| if (code->index >= ARRAY_SIZE(mipi_csis_formats)) |
| return -EINVAL; |
| |
| code->code = mipi_csis_formats[code->index].code; |
| |
| return 0; |
| } |
| |
| static int mipi_csis_set_fmt(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state, |
| struct v4l2_subdev_format *sdformat) |
| { |
| struct csis_pix_format const *csis_fmt; |
| struct v4l2_mbus_framefmt *fmt; |
| unsigned int align; |
| |
| /* |
| * The CSIS can't transcode in any way, the source format can't be |
| * modified. |
| */ |
| if (sdformat->pad == CSIS_PAD_SOURCE) |
| return v4l2_subdev_get_fmt(sd, sd_state, sdformat); |
| |
| if (sdformat->pad != CSIS_PAD_SINK) |
| return -EINVAL; |
| |
| /* |
| * Validate the media bus code and clamp and align the size. |
| * |
| * The total number of bits per line must be a multiple of 8. We thus |
| * need to align the width for formats that are not multiples of 8 |
| * bits. |
| */ |
| csis_fmt = find_csis_format(sdformat->format.code); |
| if (!csis_fmt) |
| csis_fmt = &mipi_csis_formats[0]; |
| |
| switch (csis_fmt->width % 8) { |
| case 0: |
| align = 0; |
| break; |
| case 4: |
| align = 1; |
| break; |
| case 2: |
| case 6: |
| align = 2; |
| break; |
| default: |
| /* 1, 3, 5, 7 */ |
| align = 3; |
| break; |
| } |
| |
| v4l_bound_align_image(&sdformat->format.width, 1, |
| CSIS_MAX_PIX_WIDTH, align, |
| &sdformat->format.height, 1, |
| CSIS_MAX_PIX_HEIGHT, 0, 0); |
| |
| fmt = v4l2_subdev_state_get_format(sd_state, sdformat->pad); |
| |
| fmt->code = csis_fmt->code; |
| fmt->width = sdformat->format.width; |
| fmt->height = sdformat->format.height; |
| fmt->field = V4L2_FIELD_NONE; |
| fmt->colorspace = sdformat->format.colorspace; |
| fmt->quantization = sdformat->format.quantization; |
| fmt->xfer_func = sdformat->format.xfer_func; |
| fmt->ycbcr_enc = sdformat->format.ycbcr_enc; |
| |
| sdformat->format = *fmt; |
| |
| /* Propagate the format from sink to source. */ |
| fmt = v4l2_subdev_state_get_format(sd_state, CSIS_PAD_SOURCE); |
| *fmt = sdformat->format; |
| |
| /* The format on the source pad might change due to unpacking. */ |
| fmt->code = csis_fmt->output; |
| |
| return 0; |
| } |
| |
| static int mipi_csis_get_frame_desc(struct v4l2_subdev *sd, unsigned int pad, |
| struct v4l2_mbus_frame_desc *fd) |
| { |
| struct v4l2_mbus_frame_desc_entry *entry = &fd->entry[0]; |
| const struct csis_pix_format *csis_fmt; |
| const struct v4l2_mbus_framefmt *fmt; |
| struct v4l2_subdev_state *state; |
| |
| if (pad != CSIS_PAD_SOURCE) |
| return -EINVAL; |
| |
| state = v4l2_subdev_lock_and_get_active_state(sd); |
| fmt = v4l2_subdev_state_get_format(state, CSIS_PAD_SOURCE); |
| csis_fmt = find_csis_format(fmt->code); |
| v4l2_subdev_unlock_state(state); |
| |
| if (!csis_fmt) |
| return -EPIPE; |
| |
| fd->type = V4L2_MBUS_FRAME_DESC_TYPE_PARALLEL; |
| fd->num_entries = 1; |
| |
| entry->flags = 0; |
| entry->pixelcode = csis_fmt->code; |
| entry->bus.csi2.vc = 0; |
| entry->bus.csi2.dt = csis_fmt->data_type; |
| |
| return 0; |
| } |
| |
| static int mipi_csis_init_state(struct v4l2_subdev *sd, |
| struct v4l2_subdev_state *sd_state) |
| { |
| struct v4l2_subdev_format fmt = { |
| .pad = CSIS_PAD_SINK, |
| }; |
| |
| fmt.format.code = mipi_csis_formats[0].code; |
| fmt.format.width = MIPI_CSIS_DEF_PIX_WIDTH; |
| fmt.format.height = MIPI_CSIS_DEF_PIX_HEIGHT; |
| |
| fmt.format.colorspace = V4L2_COLORSPACE_SMPTE170M; |
| fmt.format.xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt.format.colorspace); |
| fmt.format.ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt.format.colorspace); |
| fmt.format.quantization = |
| V4L2_MAP_QUANTIZATION_DEFAULT(false, fmt.format.colorspace, |
| fmt.format.ycbcr_enc); |
| |
| return mipi_csis_set_fmt(sd, sd_state, &fmt); |
| } |
| |
| static int mipi_csis_log_status(struct v4l2_subdev *sd) |
| { |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| |
| mipi_csis_log_counters(csis, true); |
| if (csis->debug.enable) |
| mipi_csis_dump_regs(csis); |
| |
| return 0; |
| } |
| |
| static const struct v4l2_subdev_core_ops mipi_csis_core_ops = { |
| .log_status = mipi_csis_log_status, |
| }; |
| |
| static const struct v4l2_subdev_video_ops mipi_csis_video_ops = { |
| .s_stream = mipi_csis_s_stream, |
| }; |
| |
| static const struct v4l2_subdev_pad_ops mipi_csis_pad_ops = { |
| .enum_mbus_code = mipi_csis_enum_mbus_code, |
| .get_fmt = v4l2_subdev_get_fmt, |
| .set_fmt = mipi_csis_set_fmt, |
| .get_frame_desc = mipi_csis_get_frame_desc, |
| }; |
| |
| static const struct v4l2_subdev_ops mipi_csis_subdev_ops = { |
| .core = &mipi_csis_core_ops, |
| .video = &mipi_csis_video_ops, |
| .pad = &mipi_csis_pad_ops, |
| }; |
| |
| static const struct v4l2_subdev_internal_ops mipi_csis_internal_ops = { |
| .init_state = mipi_csis_init_state, |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * Media entity operations |
| */ |
| |
| static int mipi_csis_link_setup(struct media_entity *entity, |
| const struct media_pad *local_pad, |
| const struct media_pad *remote_pad, u32 flags) |
| { |
| struct v4l2_subdev *sd = media_entity_to_v4l2_subdev(entity); |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| struct v4l2_subdev *remote_sd; |
| |
| dev_dbg(csis->dev, "link setup %s -> %s", remote_pad->entity->name, |
| local_pad->entity->name); |
| |
| /* We only care about the link to the source. */ |
| if (!(local_pad->flags & MEDIA_PAD_FL_SINK)) |
| return 0; |
| |
| remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity); |
| |
| if (flags & MEDIA_LNK_FL_ENABLED) { |
| if (csis->src_sd) |
| return -EBUSY; |
| |
| csis->src_sd = remote_sd; |
| } else { |
| csis->src_sd = NULL; |
| } |
| |
| return 0; |
| } |
| |
| static const struct media_entity_operations mipi_csis_entity_ops = { |
| .link_setup = mipi_csis_link_setup, |
| .link_validate = v4l2_subdev_link_validate, |
| .get_fwnode_pad = v4l2_subdev_get_fwnode_pad_1_to_1, |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * Async subdev notifier |
| */ |
| |
| static struct mipi_csis_device * |
| mipi_notifier_to_csis_state(struct v4l2_async_notifier *n) |
| { |
| return container_of(n, struct mipi_csis_device, notifier); |
| } |
| |
| static int mipi_csis_notify_bound(struct v4l2_async_notifier *notifier, |
| struct v4l2_subdev *sd, |
| struct v4l2_async_connection *asd) |
| { |
| struct mipi_csis_device *csis = mipi_notifier_to_csis_state(notifier); |
| struct media_pad *sink = &csis->sd.entity.pads[CSIS_PAD_SINK]; |
| |
| return v4l2_create_fwnode_links_to_pad(sd, sink, 0); |
| } |
| |
| static const struct v4l2_async_notifier_operations mipi_csis_notify_ops = { |
| .bound = mipi_csis_notify_bound, |
| }; |
| |
| static int mipi_csis_async_register(struct mipi_csis_device *csis) |
| { |
| struct v4l2_fwnode_endpoint vep = { |
| .bus_type = V4L2_MBUS_CSI2_DPHY, |
| }; |
| struct v4l2_async_connection *asd; |
| struct fwnode_handle *ep; |
| unsigned int i; |
| int ret; |
| |
| v4l2_async_subdev_nf_init(&csis->notifier, &csis->sd); |
| |
| ep = fwnode_graph_get_endpoint_by_id(dev_fwnode(csis->dev), 0, 0, |
| FWNODE_GRAPH_ENDPOINT_NEXT); |
| if (!ep) |
| return -ENOTCONN; |
| |
| ret = v4l2_fwnode_endpoint_parse(ep, &vep); |
| if (ret) |
| goto err_parse; |
| |
| for (i = 0; i < vep.bus.mipi_csi2.num_data_lanes; ++i) { |
| if (vep.bus.mipi_csi2.data_lanes[i] != i + 1) { |
| dev_err(csis->dev, |
| "data lanes reordering is not supported"); |
| ret = -EINVAL; |
| goto err_parse; |
| } |
| } |
| |
| csis->bus = vep.bus.mipi_csi2; |
| |
| dev_dbg(csis->dev, "data lanes: %d\n", csis->bus.num_data_lanes); |
| dev_dbg(csis->dev, "flags: 0x%08x\n", csis->bus.flags); |
| |
| asd = v4l2_async_nf_add_fwnode_remote(&csis->notifier, ep, |
| struct v4l2_async_connection); |
| if (IS_ERR(asd)) { |
| ret = PTR_ERR(asd); |
| goto err_parse; |
| } |
| |
| fwnode_handle_put(ep); |
| |
| csis->notifier.ops = &mipi_csis_notify_ops; |
| |
| ret = v4l2_async_nf_register(&csis->notifier); |
| if (ret) |
| return ret; |
| |
| return v4l2_async_register_subdev(&csis->sd); |
| |
| err_parse: |
| fwnode_handle_put(ep); |
| |
| return ret; |
| } |
| |
| /* ----------------------------------------------------------------------------- |
| * Suspend/resume |
| */ |
| |
| static int __maybe_unused mipi_csis_runtime_suspend(struct device *dev) |
| { |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| int ret; |
| |
| ret = mipi_csis_phy_disable(csis); |
| if (ret) |
| return -EAGAIN; |
| |
| mipi_csis_clk_disable(csis); |
| |
| return 0; |
| } |
| |
| static int __maybe_unused mipi_csis_runtime_resume(struct device *dev) |
| { |
| struct v4l2_subdev *sd = dev_get_drvdata(dev); |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| int ret; |
| |
| ret = mipi_csis_phy_enable(csis); |
| if (ret) |
| return -EAGAIN; |
| |
| ret = mipi_csis_clk_enable(csis); |
| if (ret) { |
| mipi_csis_phy_disable(csis); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static const struct dev_pm_ops mipi_csis_pm_ops = { |
| SET_RUNTIME_PM_OPS(mipi_csis_runtime_suspend, mipi_csis_runtime_resume, |
| NULL) |
| }; |
| |
| /* ----------------------------------------------------------------------------- |
| * Probe/remove & platform driver |
| */ |
| |
| static int mipi_csis_subdev_init(struct mipi_csis_device *csis) |
| { |
| struct v4l2_subdev *sd = &csis->sd; |
| int ret; |
| |
| v4l2_subdev_init(sd, &mipi_csis_subdev_ops); |
| sd->internal_ops = &mipi_csis_internal_ops; |
| sd->owner = THIS_MODULE; |
| snprintf(sd->name, sizeof(sd->name), "csis-%s", |
| dev_name(csis->dev)); |
| |
| sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; |
| sd->ctrl_handler = NULL; |
| |
| sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE; |
| sd->entity.ops = &mipi_csis_entity_ops; |
| |
| sd->dev = csis->dev; |
| |
| csis->pads[CSIS_PAD_SINK].flags = MEDIA_PAD_FL_SINK |
| | MEDIA_PAD_FL_MUST_CONNECT; |
| csis->pads[CSIS_PAD_SOURCE].flags = MEDIA_PAD_FL_SOURCE |
| | MEDIA_PAD_FL_MUST_CONNECT; |
| ret = media_entity_pads_init(&sd->entity, CSIS_PADS_NUM, csis->pads); |
| if (ret) |
| return ret; |
| |
| ret = v4l2_subdev_init_finalize(sd); |
| if (ret) { |
| media_entity_cleanup(&sd->entity); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int mipi_csis_parse_dt(struct mipi_csis_device *csis) |
| { |
| struct device_node *node = csis->dev->of_node; |
| |
| if (of_property_read_u32(node, "clock-frequency", |
| &csis->clk_frequency)) |
| csis->clk_frequency = DEFAULT_SCLK_CSIS_FREQ; |
| |
| return 0; |
| } |
| |
| static int mipi_csis_probe(struct platform_device *pdev) |
| { |
| struct device *dev = &pdev->dev; |
| struct mipi_csis_device *csis; |
| int irq; |
| int ret; |
| |
| csis = devm_kzalloc(dev, sizeof(*csis), GFP_KERNEL); |
| if (!csis) |
| return -ENOMEM; |
| |
| spin_lock_init(&csis->slock); |
| |
| csis->dev = dev; |
| csis->info = of_device_get_match_data(dev); |
| |
| memcpy(csis->events, mipi_csis_events, sizeof(csis->events)); |
| |
| /* Parse DT properties. */ |
| ret = mipi_csis_parse_dt(csis); |
| if (ret < 0) { |
| dev_err(dev, "Failed to parse device tree: %d\n", ret); |
| return ret; |
| } |
| |
| /* Acquire resources. */ |
| csis->regs = devm_platform_ioremap_resource(pdev, 0); |
| if (IS_ERR(csis->regs)) |
| return PTR_ERR(csis->regs); |
| |
| irq = platform_get_irq(pdev, 0); |
| if (irq < 0) |
| return irq; |
| |
| ret = mipi_csis_phy_init(csis); |
| if (ret < 0) |
| return ret; |
| |
| ret = mipi_csis_clk_get(csis); |
| if (ret < 0) |
| return ret; |
| |
| /* Reset PHY and enable the clocks. */ |
| mipi_csis_phy_reset(csis); |
| |
| /* Now that the hardware is initialized, request the interrupt. */ |
| ret = devm_request_irq(dev, irq, mipi_csis_irq_handler, 0, |
| dev_name(dev), csis); |
| if (ret) { |
| dev_err(dev, "Interrupt request failed\n"); |
| return ret; |
| } |
| |
| /* Initialize and register the subdev. */ |
| ret = mipi_csis_subdev_init(csis); |
| if (ret < 0) |
| return ret; |
| |
| platform_set_drvdata(pdev, &csis->sd); |
| |
| ret = mipi_csis_async_register(csis); |
| if (ret < 0) { |
| dev_err(dev, "async register failed: %d\n", ret); |
| goto err_cleanup; |
| } |
| |
| /* Initialize debugfs. */ |
| mipi_csis_debugfs_init(csis); |
| |
| /* Enable runtime PM. */ |
| pm_runtime_enable(dev); |
| if (!pm_runtime_enabled(dev)) { |
| ret = mipi_csis_runtime_resume(dev); |
| if (ret < 0) |
| goto err_unregister_all; |
| } |
| |
| dev_info(dev, "lanes: %d, freq: %u\n", |
| csis->bus.num_data_lanes, csis->clk_frequency); |
| |
| return 0; |
| |
| err_unregister_all: |
| mipi_csis_debugfs_exit(csis); |
| err_cleanup: |
| v4l2_subdev_cleanup(&csis->sd); |
| media_entity_cleanup(&csis->sd.entity); |
| v4l2_async_nf_unregister(&csis->notifier); |
| v4l2_async_nf_cleanup(&csis->notifier); |
| v4l2_async_unregister_subdev(&csis->sd); |
| |
| return ret; |
| } |
| |
| static void mipi_csis_remove(struct platform_device *pdev) |
| { |
| struct v4l2_subdev *sd = platform_get_drvdata(pdev); |
| struct mipi_csis_device *csis = sd_to_mipi_csis_device(sd); |
| |
| mipi_csis_debugfs_exit(csis); |
| v4l2_async_nf_unregister(&csis->notifier); |
| v4l2_async_nf_cleanup(&csis->notifier); |
| v4l2_async_unregister_subdev(&csis->sd); |
| |
| if (!pm_runtime_enabled(&pdev->dev)) |
| mipi_csis_runtime_suspend(&pdev->dev); |
| |
| pm_runtime_disable(&pdev->dev); |
| v4l2_subdev_cleanup(&csis->sd); |
| media_entity_cleanup(&csis->sd.entity); |
| pm_runtime_set_suspended(&pdev->dev); |
| } |
| |
| static const struct of_device_id mipi_csis_of_match[] = { |
| { |
| .compatible = "fsl,imx7-mipi-csi2", |
| .data = &(const struct mipi_csis_info){ |
| .version = MIPI_CSIS_V3_3, |
| .num_clocks = 3, |
| }, |
| }, { |
| .compatible = "fsl,imx8mm-mipi-csi2", |
| .data = &(const struct mipi_csis_info){ |
| .version = MIPI_CSIS_V3_6_3, |
| .num_clocks = 4, |
| }, |
| }, |
| { /* sentinel */ }, |
| }; |
| MODULE_DEVICE_TABLE(of, mipi_csis_of_match); |
| |
| static struct platform_driver mipi_csis_driver = { |
| .probe = mipi_csis_probe, |
| .remove_new = mipi_csis_remove, |
| .driver = { |
| .of_match_table = mipi_csis_of_match, |
| .name = CSIS_DRIVER_NAME, |
| .pm = &mipi_csis_pm_ops, |
| }, |
| }; |
| |
| module_platform_driver(mipi_csis_driver); |
| |
| MODULE_DESCRIPTION("i.MX7 & i.MX8 MIPI CSI-2 receiver driver"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_ALIAS("platform:imx-mipi-csi2"); |