| # SPDX-License-Identifier: GPL-2.0-only |
| # |
| # IDE ATA ATAPI Block device driver configuration |
| # |
| |
| # Select HAVE_IDE if IDE is supported |
| config HAVE_IDE |
| bool |
| |
| menuconfig IDE |
| tristate "ATA/ATAPI/MFM/RLL support (DEPRECATED)" |
| depends on HAVE_IDE |
| depends on BLOCK |
| select BLK_SCSI_REQUEST |
| help |
| If you say Y here, your kernel will be able to manage ATA/(E)IDE and |
| ATAPI units. The most common cases are IDE hard drives and ATAPI |
| CD-ROM drives. |
| |
| This subsystem is currently in maintenance mode with only bug fix |
| changes applied. Users of ATA hardware are encouraged to migrate to |
| the newer ATA subsystem ("Serial ATA (prod) and Parallel ATA |
| (experimental) drivers") which is more actively maintained. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ide-core. |
| |
| For further information, please read <file:Documentation/ide/ide.rst>. |
| |
| If unsure, say N. |
| |
| if IDE |
| |
| comment "Please see Documentation/ide/ide.rst for help/info on IDE drives" |
| |
| config IDE_XFER_MODE |
| bool |
| |
| config IDE_TIMINGS |
| bool |
| select IDE_XFER_MODE |
| |
| config IDE_ATAPI |
| bool |
| |
| config IDE_LEGACY |
| bool |
| |
| config BLK_DEV_IDE_SATA |
| bool "Support for SATA (deprecated; conflicts with libata SATA driver)" |
| default n |
| help |
| There are two drivers for Serial ATA controllers. |
| |
| The main driver, "libata", uses the SCSI subsystem |
| and supports most modern SATA controllers. In order to use it |
| you may take a look at "Serial ATA (prod) and Parallel ATA |
| (experimental) drivers". |
| |
| The IDE driver (which you are currently configuring) supports |
| a few first-generation SATA controllers. |
| |
| In order to eliminate conflicts between the two subsystems, |
| this config option enables the IDE driver's SATA support. |
| Normally this is disabled, as it is preferred that libata |
| supports SATA controllers, and this (IDE) driver supports |
| PATA controllers. |
| |
| If unsure, say N. |
| |
| config IDE_GD |
| tristate "generic ATA/ATAPI disk support" |
| default y |
| help |
| Support for ATA/ATAPI disks (including ATAPI floppy drives). |
| |
| To compile this driver as a module, choose M here. |
| The module will be called ide-gd_mod. |
| |
| If unsure, say Y. |
| |
| config IDE_GD_ATA |
| bool "ATA disk support" |
| depends on IDE_GD |
| default y |
| help |
| This will include support for ATA hard disks. |
| |
| If unsure, say Y. |
| |
| config IDE_GD_ATAPI |
| bool "ATAPI floppy support" |
| depends on IDE_GD |
| select IDE_ATAPI |
| help |
| This will include support for ATAPI floppy drives |
| (i.e. Iomega ZIP or MKE LS-120). |
| |
| For information about jumper settings and the question |
| of when a ZIP drive uses a partition table, see |
| <http://www.win.tue.nl/~aeb/linux/zip/zip-1.html>. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_IDECS |
| tristate "PCMCIA IDE support" |
| depends on PCMCIA |
| help |
| Support for Compact Flash cards, outboard IDE disks, tape drives, |
| and CD-ROM drives connected through a PCMCIA card. |
| |
| config BLK_DEV_DELKIN |
| tristate "Cardbus IDE support (Delkin/ASKA/Workbit)" |
| depends on CARDBUS && PCI |
| help |
| Support for Delkin, ASKA, and Workbit Cardbus CompactFlash |
| Adapters. This may also work for similar SD and XD adapters. |
| |
| config BLK_DEV_IDECD |
| tristate "Include IDE/ATAPI CDROM support" |
| depends on BLK_DEV |
| select IDE_ATAPI |
| select CDROM |
| help |
| If you have a CD-ROM drive using the ATAPI protocol, say Y. ATAPI is |
| a newer protocol used by IDE CD-ROM and TAPE drives, similar to the |
| SCSI protocol. Most new CD-ROM drives use ATAPI, including the |
| NEC-260, Mitsumi FX400, Sony 55E, and just about all non-SCSI |
| double(2X) or better speed drives. |
| |
| If you say Y here, the CD-ROM drive will be identified at boot time |
| along with other IDE devices, as "hdb" or "hdc", or something |
| similar (check the boot messages with dmesg). If this is your only |
| CD-ROM drive, you can say N to all other CD-ROM options, but be sure |
| to say Y or M to "ISO 9660 CD-ROM file system support". |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ide-cd. |
| |
| config BLK_DEV_IDECD_VERBOSE_ERRORS |
| bool "Verbose error logging for IDE/ATAPI CDROM driver" if EXPERT |
| depends on BLK_DEV_IDECD |
| default y |
| help |
| Turn this on to have the driver print out the meanings of the |
| ATAPI error codes. This will use up additional 8kB of kernel-space |
| memory, though. |
| |
| config BLK_DEV_IDETAPE |
| tristate "Include IDE/ATAPI TAPE support" |
| select IDE_ATAPI |
| help |
| If you have an IDE tape drive using the ATAPI protocol, say Y. |
| ATAPI is a newer protocol used by IDE tape and CD-ROM drives, |
| similar to the SCSI protocol. If you have an SCSI tape drive |
| however, you can say N here. |
| |
| You should also say Y if you have an OnStream DI-30 tape drive; this |
| will not work with the SCSI protocol, until there is support for the |
| SC-30 and SC-50 versions. |
| |
| If you say Y here, the tape drive will be identified at boot time |
| along with other IDE devices, as "hdb" or "hdc", or something |
| similar, and will be mapped to a character device such as "ht0" |
| (check the boot messages with dmesg). Be sure to consult the |
| <file:drivers/ide/ide-tape.c> and <file:Documentation/ide/ide.rst> |
| files for usage information. |
| |
| To compile this driver as a module, choose M here: the |
| module will be called ide-tape. |
| |
| config BLK_DEV_IDEACPI |
| bool "IDE ACPI support" |
| depends on ACPI |
| help |
| Implement ACPI support for generic IDE devices. On modern |
| machines ACPI support is required to properly handle ACPI S3 states. |
| |
| config IDE_TASK_IOCTL |
| bool "IDE Taskfile Access" |
| help |
| This is a direct raw access to the media. It is a complex but |
| elegant solution to test and validate the domain of the hardware and |
| perform below the driver data recovery if needed. This is the most |
| basic form of media-forensics. |
| |
| If you are unsure, say N here. |
| |
| config IDE_PROC_FS |
| bool "legacy /proc/ide/ support" |
| depends on IDE && PROC_FS |
| default y |
| help |
| This option enables support for the various files in |
| /proc/ide. In Linux 2.6 this has been superseded by |
| files in sysfs but many legacy applications rely on this. |
| |
| If unsure say Y. |
| |
| comment "IDE chipset support/bugfixes" |
| |
| config IDE_GENERIC |
| tristate "generic/default IDE chipset support" |
| depends on ALPHA || X86 || IA64 || MIPS || ARCH_RPC |
| default ARM && ARCH_RPC |
| help |
| This is the generic IDE driver. This driver attaches to the |
| fixed legacy ports (e.g. on PCs 0x1f0/0x170, 0x1e8/0x168 and |
| so on). Please note that if this driver is built into the |
| kernel or loaded before other ATA (IDE or libata) drivers |
| and the controller is located at legacy ports, this driver |
| may grab those ports and thus can prevent the controller |
| specific driver from attaching. |
| |
| Also, currently, IDE generic doesn't allow IRQ sharing |
| meaning that the IRQs it grabs won't be available to other |
| controllers sharing those IRQs which usually makes drivers |
| for those controllers fail. Generally, it's not a good idea |
| to load IDE generic driver on modern systems. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_PLATFORM |
| tristate "Platform driver for IDE interfaces" |
| help |
| This is the platform IDE driver, used mostly for Memory Mapped |
| IDE devices, like Compact Flashes running in True IDE mode. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_CMD640 |
| tristate "CMD640 chipset bugfix/support" |
| depends on X86 |
| select IDE_TIMINGS |
| help |
| The CMD-Technologies CMD640 IDE chip is used on many common 486 and |
| Pentium motherboards, usually in combination with a "Neptune" or |
| "SiS" chipset. Unfortunately, it has a number of rather nasty |
| design flaws that can cause severe data corruption under many common |
| conditions. Say Y here to include code which tries to automatically |
| detect and correct the problems under Linux. This option also |
| enables access to the secondary IDE ports in some CMD640 based |
| systems. |
| |
| This driver will work automatically in PCI based systems (most new |
| systems have PCI slots). But if your system uses VESA local bus |
| (VLB) instead of PCI, you must also supply a kernel boot parameter |
| to enable the CMD640 bugfix/support: "cmd640.probe_vlb". (Try "man |
| bootparam" or see the documentation of your boot loader about how to |
| pass options to the kernel.) |
| |
| The CMD640 chip is also used on add-in cards by Acculogic, and on |
| the "CSA-6400E PCI to IDE controller" that some people have. For |
| details, read <file:Documentation/ide/ide.rst>. |
| |
| config BLK_DEV_CMD640_ENHANCED |
| bool "CMD640 enhanced support" |
| depends on BLK_DEV_CMD640 |
| help |
| This option includes support for setting/autotuning PIO modes and |
| prefetch on CMD640 IDE interfaces. For details, read |
| <file:Documentation/ide/ide.rst>. If you have a CMD640 IDE interface |
| and your BIOS does not already do this for you, then say Y here. |
| Otherwise say N. |
| |
| config BLK_DEV_IDEPNP |
| tristate "PNP EIDE support" |
| depends on PNP |
| help |
| If you have a PnP (Plug and Play) compatible EIDE card and |
| would like the kernel to automatically detect and activate |
| it, say Y here. |
| |
| config BLK_DEV_IDEDMA_SFF |
| bool |
| |
| if PCI |
| |
| comment "PCI IDE chipsets support" |
| |
| config BLK_DEV_IDEPCI |
| bool |
| |
| config IDEPCI_PCIBUS_ORDER |
| bool "Probe IDE PCI devices in the PCI bus order (DEPRECATED)" |
| depends on IDE=y && BLK_DEV_IDEPCI |
| default y |
| help |
| Probe IDE PCI devices in the order in which they appear on the |
| PCI bus (i.e. 00:1f.1 PCI device before 02:01.0 PCI device) |
| instead of the order in which IDE PCI host drivers are loaded. |
| |
| Please note that this method of assuring stable naming of |
| IDE devices is unreliable and use other means for achieving |
| it (i.e. udev). |
| |
| If in doubt, say N. |
| |
| # TODO: split it on per host driver config options (or module parameters) |
| config BLK_DEV_OFFBOARD |
| bool "Boot off-board chipsets first support (DEPRECATED)" |
| depends on BLK_DEV_IDEPCI && (BLK_DEV_AEC62XX || BLK_DEV_GENERIC || BLK_DEV_HPT366 || BLK_DEV_PDC202XX_NEW || BLK_DEV_PDC202XX_OLD || BLK_DEV_TC86C001) |
| help |
| Normally, IDE controllers built into the motherboard (on-board |
| controllers) are assigned to ide0 and ide1 while those on add-in PCI |
| cards (off-board controllers) are relegated to ide2 and ide3. |
| Answering Y here will allow you to reverse the situation, with |
| off-board controllers on ide0/1 and on-board controllers on ide2/3. |
| This can improve the usability of some boot managers such as lilo |
| when booting from a drive on an off-board controller. |
| |
| Note that, if you do this, the order of the hd* devices will be |
| rearranged which may require modification of fstab and other files. |
| |
| Please also note that this method of assuring stable naming of |
| IDE devices is unreliable and use other means for achieving it |
| (i.e. udev). |
| |
| If in doubt, say N. |
| |
| config BLK_DEV_GENERIC |
| tristate "Generic PCI IDE Chipset Support" |
| select BLK_DEV_IDEPCI |
| help |
| This option provides generic support for various PCI IDE Chipsets |
| which otherwise might not be supported. |
| |
| config BLK_DEV_OPTI621 |
| tristate "OPTi 82C621 chipset enhanced support" |
| select BLK_DEV_IDEPCI |
| help |
| This is a driver for the OPTi 82C621 EIDE controller. |
| Please read the comments at the top of <file:drivers/ide/opti621.c>. |
| |
| config BLK_DEV_RZ1000 |
| tristate "RZ1000 chipset bugfix/support" |
| depends on X86 |
| select BLK_DEV_IDEPCI |
| help |
| The PC-Technologies RZ1000 IDE chip is used on many common 486 and |
| Pentium motherboards, usually along with the "Neptune" chipset. |
| Unfortunately, it has a rather nasty design flaw that can cause |
| severe data corruption under many conditions. Say Y here to include |
| code which automatically detects and corrects the problem under |
| Linux. This may slow disk throughput by a few percent, but at least |
| things will operate 100% reliably. |
| |
| config BLK_DEV_IDEDMA_PCI |
| bool |
| select BLK_DEV_IDEPCI |
| select BLK_DEV_IDEDMA_SFF |
| |
| config BLK_DEV_AEC62XX |
| tristate "AEC62XX chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds explicit support for Acard AEC62xx (Artop ATP8xx) |
| IDE controllers. This allows the kernel to change PIO, DMA and UDMA |
| speeds and to configure the chip to optimum performance. |
| |
| config BLK_DEV_ALI15X3 |
| tristate "ALI M15x3 chipset support" |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver ensures (U)DMA support for ALI 1533, 1543 and 1543C |
| onboard chipsets. It also tests for Simplex mode and enables |
| normal dual channel support. |
| |
| Please read the comments at the top of |
| <file:drivers/ide/alim15x3.c>. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_AMD74XX |
| tristate "AMD and nVidia IDE support" |
| depends on !ARM |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds explicit support for AMD-7xx and AMD-8111 chips |
| and also for the nVidia nForce chip. This allows the kernel to |
| change PIO, DMA and UDMA speeds and to configure the chip to |
| optimum performance. |
| |
| config BLK_DEV_ATIIXP |
| tristate "ATI IXP chipset IDE support" |
| depends on X86 |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds explicit support for ATI IXP chipset. |
| This allows the kernel to change PIO, DMA and UDMA speeds |
| and to configure the chip to optimum performance. |
| |
| Say Y here if you have an ATI IXP chipset IDE controller. |
| |
| config BLK_DEV_CMD64X |
| tristate "CMD64{3|6|8|9} chipset support" |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Say Y here if you have an IDE controller which uses any of these |
| chipsets: CMD643, CMD646, or CMD648. |
| |
| config BLK_DEV_TRIFLEX |
| tristate "Compaq Triflex IDE support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Say Y here if you have a Compaq Triflex IDE controller, such |
| as those commonly found on Compaq Pentium-Pro systems |
| |
| config BLK_DEV_CY82C693 |
| tristate "CY82C693 chipset support" |
| depends on ALPHA |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds detection and support for the CY82C693 chipset |
| used on Digital's PC-Alpha 164SX boards. |
| |
| config BLK_DEV_CS5520 |
| tristate "Cyrix CS5510/20 MediaGX chipset support (VERY EXPERIMENTAL)" |
| depends on X86_32 || COMPILE_TEST |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Include support for PIO tuning and virtual DMA on the Cyrix MediaGX |
| 5510/5520 chipset. This will automatically be detected and |
| configured if found. |
| |
| It is safe to say Y to this question. |
| |
| config BLK_DEV_CS5530 |
| tristate "Cyrix/National Semiconductor CS5530 MediaGX chipset support" |
| depends on X86_32 || COMPILE_TEST |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Include support for UDMA on the Cyrix MediaGX 5530 chipset. This |
| will automatically be detected and configured if found. |
| |
| It is safe to say Y to this question. |
| |
| config BLK_DEV_CS5535 |
| tristate "AMD CS5535 chipset support" |
| depends on X86_32 |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Include support for UDMA on the NSC/AMD CS5535 companion chipset. |
| This will automatically be detected and configured if found. |
| |
| It is safe to say Y to this question. |
| |
| config BLK_DEV_CS5536 |
| tristate "CS5536 chipset support" |
| depends on X86_32 |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This option enables support for the AMD CS5536 |
| companion chip used with the Geode LX processor family. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_HPT366 |
| tristate "HPT36X/37X chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| HPT366 is an Ultra DMA chipset for ATA-66. |
| HPT368 is an Ultra DMA chipset for ATA-66 RAID Based. |
| HPT370 is an Ultra DMA chipset for ATA-100. |
| HPT372 is an Ultra DMA chipset for ATA-100. |
| HPT374 is an Ultra DMA chipset for ATA-100. |
| |
| This driver adds up to 4 more EIDE devices sharing a single |
| interrupt. |
| |
| The HPT366 chipset in its current form is bootable. One solution |
| for this problem are special LILO commands for redirecting the |
| reference to device 0x80. The other solution is to say Y to "Boot |
| off-board chipsets first support" (CONFIG_BLK_DEV_OFFBOARD) unless |
| your mother board has the chipset natively mounted. Regardless one |
| should use the fore mentioned option and call at LILO. |
| |
| This driver requires dynamic tuning of the chipset during the |
| ide-probe at boot. It is reported to support DVD II drives, by the |
| manufacturer. |
| |
| config BLK_DEV_JMICRON |
| tristate "JMicron JMB36x support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Basic support for the JMicron ATA controllers. For full support |
| use the libata drivers. |
| |
| config BLK_DEV_SC1200 |
| tristate "National SCx200 chipset support" |
| depends on X86_32 || COMPILE_TEST |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for the on-board IDE controller on the |
| National SCx200 series of embedded x86 "Geode" systems. |
| |
| config BLK_DEV_PIIX |
| tristate "Intel PIIX/ICH chipsets support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds explicit support for Intel PIIX and ICH chips. |
| This allows the kernel to change PIO, DMA and UDMA speeds and to |
| configure the chip to optimum performance. |
| |
| config BLK_DEV_IT8172 |
| tristate "IT8172 IDE support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for the IDE controller on the |
| IT8172 System Controller. |
| |
| config BLK_DEV_IT8213 |
| tristate "IT8213 IDE support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for the ITE 8213 IDE controller. |
| |
| config BLK_DEV_IT821X |
| tristate "IT821X IDE support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for the ITE 8211 IDE controller and the |
| IT 8212 IDE RAID controller in both RAID and pass-through mode. |
| |
| config BLK_DEV_NS87415 |
| tristate "NS87415 chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds detection and support for the NS87415 chip |
| (used mainly on SPARC64 and PA-RISC machines). |
| |
| Please read the comments at the top of <file:drivers/ide/ns87415.c>. |
| |
| config BLK_DEV_PDC202XX_OLD |
| tristate "PROMISE PDC202{46|62|65|67} support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| Promise Ultra33 or PDC20246 |
| Promise Ultra66 or PDC20262 |
| Promise Ultra100 or PDC20265/PDC20267/PDC20268 |
| |
| This driver adds up to 4 more EIDE devices sharing a single |
| interrupt. This add-on card is a bootable PCI UDMA controller. Since |
| multiple cards can be installed and there are BIOS ROM problems that |
| happen if the BIOS revisions of all installed cards (three-max) do |
| not match, the driver attempts to do dynamic tuning of the chipset |
| at boot-time for max-speed. Ultra33 BIOS 1.25 or newer is required |
| for more than one card. |
| |
| Please read the comments at the top of |
| <file:drivers/ide/pdc202xx_old.c>. |
| |
| If unsure, say N. |
| |
| config BLK_DEV_PDC202XX_NEW |
| tristate "PROMISE PDC202{68|69|70|71|75|76|77} support" |
| select BLK_DEV_IDEDMA_PCI |
| |
| config BLK_DEV_SVWKS |
| tristate "ServerWorks OSB4/CSB5/CSB6 chipsets support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds PIO/(U)DMA support for the ServerWorks OSB4/CSB5 |
| chipsets. |
| |
| config BLK_DEV_SIIMAGE |
| tristate "Silicon Image chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds PIO/(U)DMA support for the SI CMD680 and SII |
| 3112 (Serial ATA) chips. |
| |
| config BLK_DEV_SIS5513 |
| tristate "SiS5513 chipset support" |
| depends on X86 |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver ensures (U)DMA support for SIS5513 chipset family based |
| mainboards. |
| |
| The following chipsets are supported: |
| ATA16: SiS5511, SiS5513 |
| ATA33: SiS5591, SiS5597, SiS5598, SiS5600 |
| ATA66: SiS530, SiS540, SiS620, SiS630, SiS640 |
| ATA100: SiS635, SiS645, SiS650, SiS730, SiS735, SiS740, |
| SiS745, SiS750 |
| |
| Please read the comments at the top of <file:drivers/ide/sis5513.c>. |
| |
| config BLK_DEV_SL82C105 |
| tristate "Winbond SL82c105 support" |
| depends on (PPC || ARM) |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| If you have a Winbond SL82c105 IDE controller, say Y here to enable |
| special configuration for this chip. This is common on various CHRP |
| motherboards, but could be used elsewhere. If in doubt, say Y. |
| |
| config BLK_DEV_SLC90E66 |
| tristate "SLC90E66 chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver ensures (U)DMA support for Victory66 SouthBridges for |
| SMsC with Intel NorthBridges. This is an Ultra66 based chipset. |
| The nice thing about it is that you can mix Ultra/DMA/PIO devices |
| and it will handle timing cycles. Since this is an improved |
| look-a-like to the PIIX4 it should be a nice addition. |
| |
| Please read the comments at the top of |
| <file:drivers/ide/slc90e66.c>. |
| |
| config BLK_DEV_TRM290 |
| tristate "Tekram TRM290 chipset support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for bus master DMA transfers |
| using the Tekram TRM290 PCI IDE chip. Volunteers are |
| needed for further tweaking and development. |
| Please read the comments at the top of <file:drivers/ide/trm290.c>. |
| |
| config BLK_DEV_VIA82CXXX |
| tristate "VIA82CXXX chipset support" |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds explicit support for VIA BusMastering IDE chips. |
| This allows the kernel to change PIO, DMA and UDMA speeds and to |
| configure the chip to optimum performance. |
| |
| config BLK_DEV_TC86C001 |
| tristate "Toshiba TC86C001 support" |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver adds support for Toshiba TC86C001 GOKU-S chip. |
| |
| endif |
| |
| # TODO: BLK_DEV_IDEDMA_PCI -> BLK_DEV_IDEDMA_SFF |
| config BLK_DEV_IDE_PMAC |
| tristate "PowerMac on-board IDE support" |
| depends on PPC_PMAC |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_PCI |
| help |
| This driver provides support for the on-board IDE controller on |
| most of the recent Apple Power Macintoshes and PowerBooks. |
| If unsure, say Y. |
| |
| config BLK_DEV_IDE_PMAC_ATA100FIRST |
| bool "Probe on-board ATA/100 (Kauai) first" |
| depends on BLK_DEV_IDE_PMAC |
| help |
| This option will cause the ATA/100 controller found in UniNorth2 |
| based machines (Windtunnel PowerMac, Aluminium PowerBooks, ...) |
| to be probed before the ATA/66 and ATA/33 controllers. Without |
| these, those machine used to have the hard disk on hdc and the |
| CD-ROM on hda. This option changes this to more natural hda for |
| hard disk and hdc for CD-ROM. |
| |
| config BLK_DEV_IDE_TX4938 |
| tristate "TX4938 internal IDE support" |
| depends on SOC_TX4938 |
| select IDE_TIMINGS |
| |
| config BLK_DEV_IDE_TX4939 |
| tristate "TX4939 internal IDE support" |
| depends on SOC_TX4939 |
| select BLK_DEV_IDEDMA_SFF |
| |
| config BLK_DEV_IDE_ICSIDE |
| tristate "ICS IDE interface support" |
| depends on ARM && ARCH_ACORN |
| help |
| On Acorn systems, say Y here if you wish to use the ICS IDE |
| interface card. This is not required for ICS partition support. |
| If you are unsure, say N to this. |
| |
| config BLK_DEV_IDEDMA_ICS |
| bool "ICS DMA support" |
| depends on BLK_DEV_IDE_ICSIDE |
| help |
| Say Y here if you want to add DMA (Direct Memory Access) support to |
| the ICS IDE driver. |
| |
| config BLK_DEV_IDE_RAPIDE |
| tristate "RapIDE interface support" |
| depends on ARM && ARCH_ACORN |
| help |
| Say Y here if you want to support the Yellowstone RapIDE controller |
| manufactured for use with Acorn computers. |
| |
| config BLK_DEV_GAYLE |
| tristate "Amiga Gayle IDE interface support" |
| depends on AMIGA |
| help |
| This is the IDE driver for the Amiga Gayle IDE interface. It supports |
| both the `A1200 style' and `A4000 style' of the Gayle IDE interface, |
| This includes on-board IDE interfaces on some Amiga models (A600, |
| A1200, A4000, and A4000T), and IDE interfaces on the Zorro expansion |
| bus (M-Tech E-Matrix 530 expansion card). |
| |
| It also provides support for the so-called `IDE doublers' (made |
| by various manufacturers, e.g. Eyetech) that can be connected to |
| the on-board IDE interface of some Amiga models. Using such an IDE |
| doubler, you can connect up to four instead of two IDE devices to |
| the Amiga's on-board IDE interface. The feature is enabled at kernel |
| runtime using the "gayle.doubler" kernel boot parameter. |
| |
| Say Y if you have an Amiga with a Gayle IDE interface and want to use |
| IDE devices (hard disks, CD-ROM drives, etc.) that are connected to |
| it. |
| |
| Note that you also have to enable Zorro bus support if you want to |
| use Gayle IDE interfaces on the Zorro expansion bus. |
| |
| config BLK_DEV_BUDDHA |
| tristate "Buddha/Catweasel/X-Surf IDE interface support" |
| depends on ZORRO |
| help |
| This is the IDE driver for the IDE interfaces on the Buddha, Catweasel |
| and X-Surf expansion boards. It supports up to two interfaces on the |
| Buddha, three on the Catweasel and two on the X-Surf. |
| |
| Say Y if you have a Buddha or Catweasel expansion board and want to |
| use IDE devices (hard disks, CD-ROM drives, etc.) that are connected |
| to one of its IDE interfaces. |
| |
| config BLK_DEV_FALCON_IDE |
| tristate "Falcon IDE interface support" |
| depends on ATARI |
| help |
| This is the IDE driver for the on-board IDE interface on the Atari |
| Falcon. Say Y if you have a Falcon and want to use IDE devices (hard |
| disks, CD-ROM drives, etc.) that are connected to the on-board IDE |
| interface. |
| |
| config BLK_DEV_MAC_IDE |
| tristate "Macintosh Quadra/Powerbook IDE interface support" |
| depends on MAC |
| help |
| This is the IDE driver for the on-board IDE interface on some m68k |
| Macintosh models. It supports both the `Quadra style' (used in |
| Quadra/ Centris 630 and Performa 588 models) and `Powerbook style' |
| (used in the Powerbook 150 and 190 models) IDE interface. |
| |
| Say Y if you have such an Macintosh model and want to use IDE |
| devices (hard disks, CD-ROM drives, etc.) that are connected to the |
| on-board IDE interface. |
| |
| config BLK_DEV_Q40IDE |
| tristate "Q40/Q60 IDE interface support" |
| depends on Q40 |
| help |
| Enable the on-board IDE controller in the Q40/Q60. This should |
| normally be on; disable it only if you are running a custom hard |
| drive subsystem through an expansion card. |
| |
| config BLK_DEV_PALMCHIP_BK3710 |
| tristate "Palmchip bk3710 IDE controller support" |
| depends on ARCH_DAVINCI |
| select IDE_TIMINGS |
| select BLK_DEV_IDEDMA_SFF |
| help |
| Say Y here if you want to support the onchip IDE controller on the |
| TI DaVinci SoC |
| |
| # no isa -> no vlb |
| if ISA && (ALPHA || X86 || MIPS) |
| |
| comment "Other IDE chipsets support" |
| comment "Note: most of these also require special kernel boot parameters" |
| |
| config BLK_DEV_4DRIVES |
| tristate "Generic 4 drives/port support" |
| help |
| Certain older chipsets, including the Tekram 690CD, use a single set |
| of I/O ports at 0x1f0 to control up to four drives, instead of the |
| customary two drives per port. Support for this can be enabled at |
| runtime using the "ide-4drives.probe" kernel boot parameter if you |
| say Y here. |
| |
| config BLK_DEV_ALI14XX |
| tristate "ALI M14xx support" |
| select IDE_TIMINGS |
| select IDE_LEGACY |
| help |
| This driver is enabled at runtime using the "ali14xx.probe" kernel |
| boot parameter. It enables support for the secondary IDE interface |
| of the ALI M1439/1443/1445/1487/1489 chipsets, and permits faster |
| I/O speeds to be set as well. |
| See the files <file:Documentation/ide/ide.rst> and |
| <file:drivers/ide/ali14xx.c> for more info. |
| |
| config BLK_DEV_DTC2278 |
| tristate "DTC-2278 support" |
| select IDE_XFER_MODE |
| select IDE_LEGACY |
| help |
| This driver is enabled at runtime using the "dtc2278.probe" kernel |
| boot parameter. It enables support for the secondary IDE interface |
| of the DTC-2278 card, and permits faster I/O speeds to be set as |
| well. See the <file:Documentation/ide/ide.rst> and |
| <file:drivers/ide/dtc2278.c> files for more info. |
| |
| config BLK_DEV_HT6560B |
| tristate "Holtek HT6560B support" |
| select IDE_TIMINGS |
| select IDE_LEGACY |
| help |
| This driver is enabled at runtime using the "ht6560b.probe" kernel |
| boot parameter. It enables support for the secondary IDE interface |
| of the Holtek card, and permits faster I/O speeds to be set as well. |
| See the <file:Documentation/ide/ide.rst> and |
| <file:drivers/ide/ht6560b.c> files for more info. |
| |
| config BLK_DEV_QD65XX |
| tristate "QDI QD65xx support" |
| select IDE_TIMINGS |
| select IDE_LEGACY |
| help |
| This driver is enabled at runtime using the "qd65xx.probe" kernel |
| boot parameter. It permits faster I/O speeds to be set. See the |
| <file:Documentation/ide/ide.rst> and <file:drivers/ide/qd65xx.c> |
| for more info. |
| |
| config BLK_DEV_UMC8672 |
| tristate "UMC-8672 support" |
| select IDE_XFER_MODE |
| select IDE_LEGACY |
| help |
| This driver is enabled at runtime using the "umc8672.probe" kernel |
| boot parameter. It enables support for the secondary IDE interface |
| of the UMC-8672, and permits faster I/O speeds to be set as well. |
| See the files <file:Documentation/ide/ide.rst> and |
| <file:drivers/ide/umc8672.c> for more info. |
| |
| endif |
| |
| config BLK_DEV_IDEDMA |
| def_bool BLK_DEV_IDEDMA_SFF || BLK_DEV_IDEDMA_ICS |
| select IDE_XFER_MODE |
| |
| endif # IDE |
