| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Device Tree Source for Sunplus SP7021 |
| * |
| * Copyright (C) 2021 Sunplus Technology Co. |
| */ |
| |
| #include <dt-bindings/clock/sunplus,sp7021-clkc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/reset/sunplus,sp7021-reset.h> |
| #include <dt-bindings/pinctrl/sppctl-sp7021.h> |
| #include <dt-bindings/gpio/gpio.h> |
| |
| #define XTAL 27000000 |
| |
| / { |
| compatible = "sunplus,sp7021"; |
| model = "Sunplus SP7021"; |
| |
| clocks { |
| extclk: osc0 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <XTAL>; |
| clock-output-names = "extclk"; |
| }; |
| }; |
| |
| soc@9c000000 { |
| compatible = "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x9c000000 0x400000>; |
| interrupt-parent = <&intc>; |
| |
| clkc: clock-controller@4 { |
| compatible = "sunplus,sp7021-clkc"; |
| reg = <0x4 0x28>, |
| <0x200 0x44>, |
| <0x268 0x04>; |
| clocks = <&extclk>; |
| #clock-cells = <1>; |
| }; |
| |
| intc: interrupt-controller@780 { |
| compatible = "sunplus,sp7021-intc"; |
| reg = <0x780 0x80>, <0xa80 0x80>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| |
| otp: otp@af00 { |
| compatible = "sunplus,sp7021-ocotp"; |
| reg = <0xaf00 0x34>, <0xaf80 0x58>; |
| reg-names = "hb_gpio", "otprx"; |
| clocks = <&clkc CLK_OTPRX>; |
| resets = <&rstc RST_OTPRX>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| therm_calib: thermal-calibration@14 { |
| reg = <0x14 0x3>; |
| }; |
| disc_vol: disconnect-voltage@18 { |
| reg = <0x18 0x2>; |
| }; |
| mac_addr0: mac-address0@34 { |
| reg = <0x34 0x6>; |
| }; |
| mac_addr1: mac-address1@3a { |
| reg = <0x3a 0x6>; |
| }; |
| }; |
| |
| pctl: pinctrl@100 { |
| compatible = "sunplus,sp7021-pctl"; |
| reg = <0x100 0x100>, |
| <0x300 0x100>, |
| <0x32e4 0x1C>, |
| <0x80 0x20>; |
| reg-names = "moon2", "gpioxt", "first", "moon1"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| clocks = <&clkc CLK_GPIO>; |
| resets = <&rstc RST_GPIO>; |
| |
| emac_pins: pinmux-emac-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(49,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_CLK_OUT,0) |
| SPPCTL_IOPAD(44,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDC,0) |
| SPPCTL_IOPAD(43,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_MAC_SMI_MDIO,0) |
| SPPCTL_IOPAD(52,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXEN,0) |
| SPPCTL_IOPAD(50,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD0,0) |
| SPPCTL_IOPAD(51,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_TXD1,0) |
| SPPCTL_IOPAD(46,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_CRSDV,0) |
| SPPCTL_IOPAD(47,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD0,0) |
| SPPCTL_IOPAD(48,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXD1,0) |
| SPPCTL_IOPAD(45,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P0_MAC_RMII_RXER,0) |
| SPPCTL_IOPAD(59,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXEN,0) |
| SPPCTL_IOPAD(57,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD0,0) |
| SPPCTL_IOPAD(58,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_TXD1,0) |
| SPPCTL_IOPAD(54,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_CRSDV,0) |
| SPPCTL_IOPAD(55,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD0,0) |
| SPPCTL_IOPAD(56,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXD1,0) |
| SPPCTL_IOPAD(53,SPPCTL_PCTL_G_PMUX,MUXF_L2SW_P1_MAC_RMII_RXER,0) |
| >; |
| sunplus,zerofunc = < |
| MUXF_L2SW_LED_FLASH0 |
| MUXF_L2SW_LED_FLASH1 |
| MUXF_L2SW_LED_ON0 |
| MUXF_L2SW_LED_ON1 |
| MUXF_DAISY_MODE |
| >; |
| }; |
| |
| emmc_pins: pinmux-emmc-pins { |
| function = "CARD0_EMMC"; |
| groups = "CARD0_EMMC"; |
| }; |
| |
| leds_pins: pinmux-leds-pins { |
| sunplus,pins = < SPPCTL_IOPAD(0,SPPCTL_PCTL_G_GPIO,0,SPPCTL_PCTL_L_OUT) >; |
| }; |
| |
| sdcard_pins: pinmux-sdcard-pins { |
| function = "SD_CARD"; |
| groups = "SD_CARD"; |
| sunplus,pins = < SPPCTL_IOPAD(91, SPPCTL_PCTL_G_GPIO, 0, 0) >; |
| }; |
| |
| spi0_pins: pinmux-spi0-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(26,SPPCTL_PCTL_G_GPIO,0,0) |
| SPPCTL_IOPAD(28,SPPCTL_PCTL_G_GPIO,0,0) |
| SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DO,0) |
| SPPCTL_IOPAD(25,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_DI,0) |
| SPPCTL_IOPAD(27,SPPCTL_PCTL_G_PMUX,MUXF_SPI0S_CLK,0) |
| >; |
| }; |
| |
| uart0_pins: pinmux-uart0-pins { |
| function = "UA0"; |
| groups = "UA0"; |
| }; |
| |
| uart1_pins: pinmux-uart1-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(14,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0) |
| SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0) |
| >; |
| }; |
| |
| uart2_pins: pinmux-uart2-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(16,SPPCTL_PCTL_G_PMUX,MUXF_UA2_TX,0) |
| SPPCTL_IOPAD(17,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RX,0) |
| SPPCTL_IOPAD(18,SPPCTL_PCTL_G_PMUX,MUXF_UA2_RTS,0) |
| SPPCTL_IOPAD(19,SPPCTL_PCTL_G_PMUX,MUXF_UA2_CTS,0) |
| >; |
| }; |
| |
| uart4_pins: pinmux-uart4-pins { |
| sunplus,pins = < |
| SPPCTL_IOPAD(22,SPPCTL_PCTL_G_PMUX,MUXF_UA4_TX,0) |
| SPPCTL_IOPAD(20,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RX,0) |
| SPPCTL_IOPAD(23,SPPCTL_PCTL_G_PMUX,MUXF_UA4_RTS,0) |
| SPPCTL_IOPAD(21,SPPCTL_PCTL_G_PMUX,MUXF_UA4_CTS,0) |
| >; |
| }; |
| }; |
| |
| rstc: reset@54 { |
| compatible = "sunplus,sp7021-reset"; |
| reg = <0x54 0x28>; |
| #reset-cells = <1>; |
| }; |
| |
| rtc: rtc@3a00 { |
| compatible = "sunplus,sp7021-rtc"; |
| reg = <0x3a00 0x80>; |
| reg-names = "rtc"; |
| clocks = <&clkc CLK_RTC>; |
| resets = <&rstc RST_RTC>; |
| interrupts = <163 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| spi_controller0: spi@2d80 { |
| compatible = "sunplus,sp7021-spi"; |
| reg = <0x2d80 0x80>, <0x2e00 0x80>; |
| reg-names = "master", "slave"; |
| interrupts = <144 IRQ_TYPE_LEVEL_HIGH>, |
| <146 IRQ_TYPE_LEVEL_HIGH>, |
| <145 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma_w", "master_risc", "slave_risc"; |
| clocks = <&clkc CLK_SPI_COMBO_0>; |
| resets = <&rstc RST_SPI_COMBO_0>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&spi0_pins>; |
| cs-gpios = <&pctl 26 GPIO_ACTIVE_LOW>, |
| <&pctl 28 GPIO_ACTIVE_LOW>; |
| }; |
| |
| spi_controller1: spi@f480 { |
| compatible = "sunplus,sp7021-spi"; |
| reg = <0xf480 0x80>, <0xf500 0x80>; |
| reg-names = "master", "slave"; |
| interrupts = <67 IRQ_TYPE_LEVEL_HIGH>, |
| <69 IRQ_TYPE_LEVEL_HIGH>, |
| <68 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma_w", "master_risc", "slave_risc"; |
| clocks = <&clkc CLK_SPI_COMBO_1>; |
| resets = <&rstc RST_SPI_COMBO_1>; |
| status = "disabled"; |
| }; |
| |
| spi_controller2: spi@f600 { |
| compatible = "sunplus,sp7021-spi"; |
| reg = <0xf600 0x80>, <0xf680 0x80>; |
| reg-names = "master", "slave"; |
| interrupts = <70 IRQ_TYPE_LEVEL_HIGH>, |
| <72 IRQ_TYPE_LEVEL_HIGH>, |
| <71 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma_w", "master_risc", "slave_risc"; |
| clocks = <&clkc CLK_SPI_COMBO_2>; |
| resets = <&rstc RST_SPI_COMBO_2>; |
| status = "disabled"; |
| }; |
| |
| spi_controller3: spi@f780 { |
| compatible = "sunplus,sp7021-spi"; |
| reg = <0xf780 0x80>, <0xf800 0x80>; |
| reg-names = "master", "slave"; |
| interrupts = <73 IRQ_TYPE_LEVEL_HIGH>, |
| <75 IRQ_TYPE_LEVEL_HIGH>, |
| <74 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "dma_w", "master_risc", "slave_risc"; |
| clocks = <&clkc CLK_SPI_COMBO_3>; |
| resets = <&rstc RST_SPI_COMBO_3>; |
| status = "disabled"; |
| }; |
| |
| uart0: serial@900 { |
| compatible = "sunplus,sp7021-uart"; |
| reg = <0x900 0x80>; |
| interrupts = <53 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLK_UA0>; |
| resets = <&rstc RST_UA0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart0_pins>; |
| }; |
| |
| uart1: serial@980 { |
| compatible = "sunplus,sp7021-uart"; |
| reg = <0x980 0x80>; |
| interrupts = <54 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLK_UA1>; |
| resets = <&rstc RST_UA1>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart1_pins>; |
| status = "disabled"; |
| }; |
| |
| uart2: serial@800 { |
| compatible = "sunplus,sp7021-uart"; |
| reg = <0x800 0x80>; |
| interrupts = <55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLK_UA2>; |
| resets = <&rstc RST_UA2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| status = "disabled"; |
| }; |
| |
| uart3: serial@880 { |
| compatible = "sunplus,sp7021-uart"; |
| reg = <0x880 0x80>; |
| interrupts = <56 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLK_UA3>; |
| resets = <&rstc RST_UA3>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@8780 { |
| compatible = "sunplus,sp7021-uart"; |
| reg = <0x8780 0x80>; |
| interrupts = <134 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clkc CLK_UA4>; |
| resets = <&rstc RST_UA4>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart4_pins>; |
| status = "disabled"; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&leds_pins>; |
| system-led { |
| label = "system-led"; |
| gpios = <&pctl 0 GPIO_ACTIVE_HIGH>; |
| default-state = "off"; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| }; |
