blob: c0a0456f16749c13a12ab2653e1308add2e69baa [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2010-2011, 2013 Freescale Semiconductor, Inc.
*
* Author: Michael Johnston <michael.johnston@freescale.com>
*
* Description:
* TWR-P102x Board Setup
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/fsl/guts.h>
#include <linux/pci.h>
#include <linux/of.h>
#include <linux/of_address.h>
#include <asm/pci-bridge.h>
#include <asm/udbg.h>
#include <asm/mpic.h>
#include <soc/fsl/qe/qe.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
#include "smp.h"
#include "mpc85xx.h"
static void __init twr_p1025_pic_init(void)
{
struct mpic *mpic;
mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
MPIC_SINGLE_DEST_CPU,
0, 256, " OpenPIC ");
BUG_ON(mpic == NULL);
mpic_init(mpic);
}
/* ************************************************************************
*
* Setup the architecture
*
*/
static void __init twr_p1025_setup_arch(void)
{
if (ppc_md.progress)
ppc_md.progress("twr_p1025_setup_arch()", 0);
mpc85xx_smp_init();
fsl_pci_assign_primary();
#ifdef CONFIG_QUICC_ENGINE
mpc85xx_qe_par_io_init();
#if IS_ENABLED(CONFIG_UCC_GETH) || IS_ENABLED(CONFIG_SERIAL_QE)
if (machine_is(twr_p1025)) {
struct ccsr_guts __iomem *guts;
struct device_node *np;
np = of_find_compatible_node(NULL, NULL, "fsl,p1021-guts");
if (np) {
guts = of_iomap(np, 0);
if (!guts)
pr_err("twr_p1025: could not map global utilities register\n");
else {
/* P1025 has pins muxed for QE and other functions. To
* enable QE UEC mode, we need to set bit QE0 for UCC1
* in Eth mode, QE0 and QE3 for UCC5 in Eth mode, QE9
* and QE12 for QE MII management signals in PMUXCR
* register.
* Set QE mux bits in PMUXCR */
setbits32(&guts->pmuxcr, MPC85xx_PMUXCR_QE(0) |
MPC85xx_PMUXCR_QE(3) |
MPC85xx_PMUXCR_QE(9) |
MPC85xx_PMUXCR_QE(12));
iounmap(guts);
#if IS_ENABLED(CONFIG_SERIAL_QE)
/* On P1025TWR board, the UCC7 acted as UART port.
* However, The UCC7's CTS pin is low level in default,
* it will impact the transmission in full duplex
* communication. So disable the Flow control pin PA18.
* The UCC7 UART just can use RXD and TXD pins.
*/
par_io_config_pin(0, 18, 0, 0, 0, 0);
#endif
/* Drive PB29 to CPLD low - CPLD will then change
* muxing from LBC to QE */
par_io_config_pin(1, 29, 1, 0, 0, 0);
par_io_data_set(1, 29, 0);
}
of_node_put(np);
}
}
#endif
#endif /* CONFIG_QUICC_ENGINE */
pr_info("TWR-P1025 board from Freescale Semiconductor\n");
}
machine_arch_initcall(twr_p1025, mpc85xx_common_publish_devices);
define_machine(twr_p1025) {
.name = "TWR-P1025",
.compatible = "fsl,TWR-P1025",
.setup_arch = twr_p1025_setup_arch,
.init_IRQ = twr_p1025_pic_init,
#ifdef CONFIG_PCI
.pcibios_fixup_bus = fsl_pcibios_fixup_bus,
#endif
.get_irq = mpic_get_irq,
.progress = udbg_progress,
};