blob: 6fcc34f7b46474545404641c6a775f7dbeca3b82 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2020 Marvell International Ltd.
*/
#include "cn9130.dtsi" /* include SoC device tree */
#include <dt-bindings/gpio/gpio.h>
/ {
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
i2c0 = &cp0_i2c0;
ethernet0 = &cp0_eth0;
ethernet1 = &cp0_eth1;
ethernet2 = &cp0_eth2;
gpio1 = &cp0_gpio1;
gpio2 = &cp0_gpio2;
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>;
};
ap0_reg_mmc_vccq: ap0_mmc_vccq@0 {
compatible = "regulator-gpio";
regulator-name = "ap0_mmc_vccq";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&expander0 5 GPIO_ACTIVE_HIGH>;
states = <1800000 0x1
3300000 0x0>;
};
cp0_reg_usb3_vbus1: cp0_usb3_vbus@1 {
compatible = "regulator-fixed";
regulator-name = "cp0-xhci1-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&expander0 8 GPIO_ACTIVE_HIGH>;
};
cp0_usb3_0_phy0: cp0_usb3_phy0 {
compatible = "usb-nop-xceiv";
};
cp0_usb3_0_phy1: cp0_usb3_phy1 {
compatible = "usb-nop-xceiv";
vcc-supply = <&cp0_reg_usb3_vbus1>;
};
cp0_reg_sd_vccq: cp0_sd_vccq@0 {
compatible = "regulator-gpio";
regulator-name = "cp0_sd_vccq";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
gpios = <&cp0_gpio2 18 GPIO_ACTIVE_HIGH>;
states = <1800000 0x1
3300000 0x0>;
};
cp0_reg_sd_vcc: cp0_sd_vcc@0 {
compatible = "regulator-fixed";
regulator-name = "cp0_sd_vcc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&cp0_gpio2 19 GPIO_ACTIVE_HIGH>;
enable-active-high;
regulator-always-on;
};
sfp: sfp {
compatible = "sff,sfp";
i2c-bus = <&cp0_i2c1>;
mod-def0-gpios = <&expander0 3 GPIO_ACTIVE_LOW>;
los-gpios = <&expander0 15 GPIO_ACTIVE_HIGH>;
tx-disable-gpios = <&expander0 2 GPIO_ACTIVE_HIGH>;
tx-fault-gpios = <&cp0_gpio1 24 GPIO_ACTIVE_HIGH>;
maximum-power-milliwatt = <3000>;
status = "okay";
};
};
&uart0 {
status = "okay";
};
/* on-board eMMC U6 */
&ap_sdhci0 {
pinctrl-names = "default";
bus-width = <8>;
status = "okay";
mmc-ddr-1_8v;
vqmmc-supply = <&ap0_reg_mmc_vccq>;
};
&cp0_syscon0 {
cp0_pinctrl: pinctrl {
compatible = "marvell,cp115-standalone-pinctrl";
cp0_i2c0_pins: cp0-i2c-pins-0 {
marvell,pins = "mpp37", "mpp38";
marvell,function = "i2c0";
};
cp0_i2c1_pins: cp0-i2c-pins-1 {
marvell,pins = "mpp35", "mpp36";
marvell,function = "i2c1";
};
cp0_sdhci_cd_pins_crb: cp0-sdhci-cd-pins-crb {
marvell,pins = "mpp55";
marvell,function = "gpio";
};
cp0_sdhci_pins: cp0-sdhi-pins-0 {
marvell,pins = "mpp56", "mpp57", "mpp58",
"mpp59", "mpp60", "mpp61";
marvell,function = "sdio";
};
cp0_spi1_pins: cp0-spi-pins-1 {
marvell,pins = "mpp13", "mpp14", "mpp15", "mpp16";
marvell,function = "spi1";
};
};
};
&cp0_gpio1 {
status = "okay";
};
&cp0_gpio2 {
status = "okay";
};
&cp0_i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&cp0_i2c0_pins>;
status = "okay";
clock-frequency = <100000>;
expander0: mcp23x17@20 {
compatible = "microchip,mcp23017";
gpio-controller;
#gpio-cells = <2>;
reg = <0x20>;
status = "okay";
};
};
&cp0_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&cp0_i2c1_pins>;
clock-frequency = <100000>;
status = "okay";
};
&cp0_sdhci0 {
pinctrl-names = "default";
pinctrl-0 = <&cp0_sdhci_pins
&cp0_sdhci_cd_pins_crb>;
bus-width = <4>;
cd-gpios = <&cp0_gpio2 23 GPIO_ACTIVE_HIGH>;
vqmmc-supply = <&cp0_reg_sd_vccq>;
vmmc-supply = <&cp0_reg_sd_vcc>;
status = "okay";
};
&cp0_spi1 {
pinctrl-names = "default";
pinctrl-0 = <&cp0_spi1_pins>;
reg = <0x700680 0x50>, /* control */
<0x2000000 0x1000000>; /* CS0 */
status = "okay";
flash@0 {
#address-cells = <0x1>;
#size-cells = <0x1>;
compatible = "jedec,spi-nor";
reg = <0x0>;
/* On-board MUX does not allow higher frequencies */
spi-max-frequency = <40000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "U-Boot";
reg = <0x0 0x200000>;
};
partition@400000 {
label = "Filesystem";
reg = <0x200000 0xe00000>;
};
};
};
};
&cp0_mdio {
status = "okay";
phy0: ethernet-phy@0 {
reg = <0>;
};
switch6: ethernet-switch@6 {
/* Actual device is MV88E6393X */
compatible = "marvell,mv88e6190";
reg = <6>;
interrupt-parent = <&cp0_gpio1>;
interrupts = <28 IRQ_TYPE_LEVEL_LOW>;
interrupt-controller;
#interrupt-cells = <2>;
dsa,member = <0 0>;
ethernet-ports {
#address-cells = <1>;
#size-cells = <0>;
ethernet-port@1 {
reg = <1>;
label = "p1";
phy-handle = <&switch0phy1>;
};
ethernet-port@2 {
reg = <2>;
label = "p2";
phy-handle = <&switch0phy2>;
};
ethernet-port@3 {
reg = <3>;
label = "p3";
phy-handle = <&switch0phy3>;
};
ethernet-port@4 {
reg = <4>;
label = "p4";
phy-handle = <&switch0phy4>;
};
ethernet-port@5 {
reg = <5>;
label = "p5";
phy-handle = <&switch0phy5>;
};
ethernet-port@6 {
reg = <6>;
label = "p6";
phy-handle = <&switch0phy6>;
};
ethernet-port@7 {
reg = <7>;
label = "p7";
phy-handle = <&switch0phy7>;
};
ethernet-port@8 {
reg = <8>;
label = "p8";
phy-handle = <&switch0phy8>;
};
ethernet-port@9 {
reg = <9>;
label = "p9";
phy-mode = "10gbase-r";
sfp = <&sfp>;
managed = "in-band-status";
};
ethernet-port@a {
reg = <10>;
ethernet = <&cp0_eth0>;
phy-mode = "10gbase-r";
managed = "in-band-status";
};
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch0phy1: ethernet-phy@1 {
reg = <0x1>;
};
switch0phy2: ethernet-phy@2 {
reg = <0x2>;
};
switch0phy3: ethernet-phy@3 {
reg = <0x3>;
};
switch0phy4: ethernet-phy@4 {
reg = <0x4>;
};
switch0phy5: ethernet-phy@5 {
reg = <0x5>;
};
switch0phy6: ethernet-phy@6 {
reg = <0x6>;
};
switch0phy7: ethernet-phy@7 {
reg = <0x7>;
};
switch0phy8: ethernet-phy@8 {
reg = <0x8>;
};
};
};
};
&cp0_xmdio {
status = "okay";
nbaset_phy0: ethernet-phy@0 {
compatible = "ethernet-phy-ieee802.3-c45";
reg = <0>;
};
};
&cp0_ethernet {
status = "okay";
};
&cp0_eth0 {
/* This port is connected to 88E6393X switch */
status = "okay";
phy-mode = "10gbase-r";
managed = "in-band-status";
phys = <&cp0_comphy4 0>;
};
&cp0_eth1 {
status = "okay";
phy = <&phy0>;
phy-mode = "rgmii-id";
};
&cp0_eth2 {
/* This port uses "2500base-t" phy-mode */
status = "disabled";
phy = <&nbaset_phy0>;
phys = <&cp0_comphy5 2>;
};