| // SPDX-License-Identifier: GPL-2.0 |
| // |
| // Copyright (c) 2019 five technologies GmbH |
| // Author: Markus Reichl <m.reichl@fivetechno.de> |
| |
| #include <linux/module.h> |
| #include <linux/i2c.h> |
| #include <linux/of.h> |
| #include <linux/regulator/driver.h> |
| #include <linux/regmap.h> |
| |
| |
| #define VOL_MIN_IDX 0x00 |
| #define VOL_MAX_IDX 0x7ff |
| |
| /* Register definitions */ |
| #define MP8859_VOUT_L_REG 0 //3 lo Bits |
| #define MP8859_VOUT_H_REG 1 //8 hi Bits |
| #define MP8859_VOUT_GO_REG 2 |
| #define MP8859_IOUT_LIM_REG 3 |
| #define MP8859_CTL1_REG 4 |
| #define MP8859_CTL2_REG 5 |
| #define MP8859_RESERVED1_REG 6 |
| #define MP8859_RESERVED2_REG 7 |
| #define MP8859_RESERVED3_REG 8 |
| #define MP8859_STATUS_REG 9 |
| #define MP8859_INTERRUPT_REG 0x0A |
| #define MP8859_MASK_REG 0x0B |
| #define MP8859_ID1_REG 0x0C |
| #define MP8859_MFR_ID_REG 0x27 |
| #define MP8859_DEV_ID_REG 0x28 |
| #define MP8859_IC_REV_REG 0x29 |
| |
| #define MP8859_MAX_REG 0x29 |
| |
| #define MP8859_GO_BIT 0x01 |
| |
| #define MP8859_IOUT_LIM_MASK 0x7f |
| |
| #define MP8859_ENABLE_MASK 0x80 |
| #define MP8859_DISCHG_EN_MASK 0x10 |
| #define MP8859_MODE_MASK 0x08 |
| |
| #define MP8859_PG_MASK 0x80 |
| #define MP8859_OTP_MASK 0x40 |
| #define MP8859_OTW_MASK 0x20 |
| #define MP8859_CC_CV_MASK 0x10 |
| |
| static int mp8859_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel) |
| { |
| int ret; |
| |
| ret = regmap_write(rdev->regmap, MP8859_VOUT_L_REG, sel & 0x7); |
| |
| if (ret) |
| return ret; |
| ret = regmap_write(rdev->regmap, MP8859_VOUT_H_REG, sel >> 3); |
| |
| if (ret) |
| return ret; |
| ret = regmap_update_bits(rdev->regmap, MP8859_VOUT_GO_REG, |
| MP8859_GO_BIT, 1); |
| return ret; |
| } |
| |
| static int mp8859_get_voltage_sel(struct regulator_dev *rdev) |
| { |
| unsigned int val_tmp; |
| unsigned int val; |
| int ret; |
| |
| ret = regmap_read(rdev->regmap, MP8859_VOUT_H_REG, &val_tmp); |
| |
| if (ret) |
| return ret; |
| val = val_tmp << 3; |
| |
| ret = regmap_read(rdev->regmap, MP8859_VOUT_L_REG, &val_tmp); |
| |
| if (ret) |
| return ret; |
| val |= val_tmp & 0x07; |
| return val; |
| } |
| |
| static int mp8859_set_voltage_time_sel(struct regulator_dev *rdev, |
| unsigned int from, unsigned int to) |
| { |
| int change; |
| |
| /* The voltage ramps at 1mV/uS, selectors are 10mV */ |
| if (from > to) |
| change = from - to; |
| else |
| change = to - from; |
| |
| return change * 10 * 1000; |
| } |
| |
| static unsigned int mp8859_get_mode(struct regulator_dev *rdev) |
| { |
| unsigned int val; |
| int ret; |
| |
| ret = regmap_read(rdev->regmap, MP8859_CTL1_REG, &val); |
| if (ret != 0) { |
| dev_err(&rdev->dev, "Failed to read mode: %d\n", ret); |
| return 0; |
| } |
| |
| if (val & MP8859_MODE_MASK) |
| return REGULATOR_MODE_FAST; |
| else |
| return REGULATOR_MODE_NORMAL; |
| } |
| |
| static int mp8859_set_mode(struct regulator_dev *rdev, unsigned int mode) |
| { |
| unsigned int val; |
| |
| switch (mode) { |
| case REGULATOR_MODE_FAST: |
| val = MP8859_MODE_MASK; |
| break; |
| case REGULATOR_MODE_NORMAL: |
| val = 0; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| return regmap_update_bits(rdev->regmap, MP8859_CTL1_REG, |
| MP8859_MODE_MASK, val); |
| } |
| |
| static int mp8859_set_current_limit(struct regulator_dev *rdev, |
| int min_uA, int max_uA) |
| { |
| unsigned int cur_val, new_val; |
| int ret, i; |
| |
| /* Steps of 50mA */ |
| new_val = max_uA / 50000; |
| if (new_val > MP8859_IOUT_LIM_MASK) |
| return -EINVAL; |
| if (new_val == 0) |
| return -EINVAL; |
| |
| /* |
| * If the regulator is limiting then ramp gradually as per |
| * datasheet, otherwise just set the value directly. |
| */ |
| ret = regmap_read(rdev->regmap, MP8859_STATUS_REG, &cur_val); |
| if (ret != 0) |
| return ret; |
| if (!(cur_val & MP8859_CC_CV_MASK)) { |
| return regmap_update_bits(rdev->regmap, MP8859_IOUT_LIM_REG, |
| MP8859_IOUT_LIM_MASK, new_val); |
| } |
| |
| ret = regmap_read(rdev->regmap, MP8859_IOUT_LIM_REG, &cur_val); |
| if (ret != 0) |
| return ret; |
| |
| if (cur_val >= new_val) { |
| for (i = cur_val; i >= new_val; i--) { |
| ret = regmap_update_bits(rdev->regmap, |
| MP8859_IOUT_LIM_REG, |
| MP8859_IOUT_LIM_MASK, |
| cur_val - i); |
| if (ret != 0) |
| return ret; |
| } |
| } else { |
| for (i = cur_val; i <= new_val; i++) { |
| ret = regmap_update_bits(rdev->regmap, |
| MP8859_IOUT_LIM_REG, |
| MP8859_IOUT_LIM_MASK, |
| cur_val + i); |
| if (ret != 0) |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int mp8859_get_status(struct regulator_dev *rdev) |
| { |
| unsigned int val; |
| int ret; |
| |
| /* Output status is only meaingful when enabled */ |
| ret = regmap_read(rdev->regmap, MP8859_CTL1_REG, &val); |
| if (ret != 0) |
| return ret; |
| if (!(val & MP8859_ENABLE_MASK)) |
| return REGULATOR_STATUS_UNDEFINED; |
| |
| ret = regmap_read(rdev->regmap, MP8859_STATUS_REG, &val); |
| if (ret != 0) |
| return ret; |
| |
| if (val & MP8859_PG_MASK) |
| return REGULATOR_STATUS_ON; |
| else |
| return REGULATOR_STATUS_ERROR; |
| } |
| |
| static int mp8859_get_error_flags(struct regulator_dev *rdev, |
| unsigned int *flags) |
| { |
| unsigned int status, enabled; |
| int ret; |
| |
| *flags = 0; |
| |
| /* Output status is only meaingful when enabled */ |
| ret = regmap_read(rdev->regmap, MP8859_CTL1_REG, &enabled); |
| if (ret != 0) |
| return ret; |
| enabled &= MP8859_ENABLE_MASK; |
| |
| ret = regmap_read(rdev->regmap, MP8859_STATUS_REG, &status); |
| if (ret != 0) |
| return ret; |
| |
| if (enabled && !(status & MP8859_PG_MASK)) |
| status |= REGULATOR_ERROR_FAIL; |
| if (status & MP8859_OTP_MASK) |
| status |= REGULATOR_ERROR_OVER_TEMP; |
| if (status & MP8859_OTW_MASK) |
| status |= REGULATOR_ERROR_OVER_TEMP_WARN; |
| if (status & MP8859_CC_CV_MASK) |
| status |= REGULATOR_ERROR_OVER_CURRENT; |
| |
| return 0; |
| } |
| |
| static const struct linear_range mp8859_dcdc_ranges[] = { |
| REGULATOR_LINEAR_RANGE(0, VOL_MIN_IDX, VOL_MAX_IDX, 10000), |
| }; |
| |
| static bool mp8859_readable(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case MP8859_VOUT_L_REG: |
| case MP8859_VOUT_H_REG: |
| case MP8859_VOUT_GO_REG: |
| case MP8859_IOUT_LIM_REG: |
| case MP8859_CTL1_REG: |
| case MP8859_CTL2_REG: |
| case MP8859_STATUS_REG: |
| case MP8859_INTERRUPT_REG: |
| case MP8859_MASK_REG: |
| case MP8859_ID1_REG: |
| case MP8859_MFR_ID_REG: |
| case MP8859_DEV_ID_REG: |
| case MP8859_IC_REV_REG: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static bool mp8859_volatile(struct device *dev, unsigned int reg) |
| { |
| switch (reg) { |
| case MP8859_VOUT_GO_REG: |
| case MP8859_STATUS_REG: |
| case MP8859_INTERRUPT_REG: |
| return true; |
| default: |
| return false; |
| } |
| } |
| |
| static const struct regmap_config mp8859_regmap = { |
| .reg_bits = 8, |
| .val_bits = 8, |
| .max_register = MP8859_MAX_REG, |
| .cache_type = REGCACHE_MAPLE, |
| .readable_reg = mp8859_readable, |
| .volatile_reg = mp8859_volatile, |
| }; |
| |
| static const struct regulator_ops mp8859_ops = { |
| .set_voltage_sel = mp8859_set_voltage_sel, |
| .get_voltage_sel = mp8859_get_voltage_sel, |
| .list_voltage = regulator_list_voltage_linear_range, |
| .set_voltage_time_sel = mp8859_set_voltage_time_sel, |
| .enable = regulator_enable_regmap, |
| .disable = regulator_disable_regmap, |
| .is_enabled = regulator_is_enabled_regmap, |
| .set_mode = mp8859_set_mode, |
| .get_mode = mp8859_get_mode, |
| .set_active_discharge = regulator_set_active_discharge_regmap, |
| .set_current_limit = mp8859_set_current_limit, |
| .get_status = mp8859_get_status, |
| .get_error_flags = mp8859_get_error_flags, |
| }; |
| |
| static const struct regulator_desc mp8859_regulators[] = { |
| { |
| .id = 0, |
| .type = REGULATOR_VOLTAGE, |
| .name = "mp8859_dcdc", |
| .supply_name = "vin", |
| .of_match = of_match_ptr("mp8859_dcdc"), |
| .n_voltages = VOL_MAX_IDX + 1, |
| .linear_ranges = mp8859_dcdc_ranges, |
| .n_linear_ranges = 1, |
| .enable_reg = MP8859_CTL1_REG, |
| .enable_mask = MP8859_ENABLE_MASK, |
| .enable_val = MP8859_ENABLE_MASK, |
| .active_discharge_reg = MP8859_CTL1_REG, |
| .active_discharge_on = MP8859_DISCHG_EN_MASK, |
| .active_discharge_mask = MP8859_DISCHG_EN_MASK, |
| .ops = &mp8859_ops, |
| .owner = THIS_MODULE, |
| }, |
| }; |
| |
| static int mp8859_i2c_probe(struct i2c_client *i2c) |
| { |
| int ret; |
| struct regulator_config config = {.dev = &i2c->dev}; |
| struct regmap *regmap = devm_regmap_init_i2c(i2c, &mp8859_regmap); |
| struct regulator_dev *rdev; |
| unsigned int val, rev; |
| |
| if (IS_ERR(regmap)) { |
| ret = PTR_ERR(regmap); |
| dev_err(&i2c->dev, "regmap init failed: %d\n", ret); |
| return ret; |
| } |
| |
| ret = regmap_read(regmap, MP8859_MFR_ID_REG, &val); |
| if (ret != 0) { |
| dev_err(&i2c->dev, "Failed to read manufacturer ID: %d\n", ret); |
| return ret; |
| } |
| if (val != 0x9) { |
| dev_err(&i2c->dev, "Manufacturer ID %x != 9\n", val); |
| return -EINVAL; |
| } |
| |
| ret = regmap_read(regmap, MP8859_DEV_ID_REG, &val); |
| if (ret != 0) { |
| dev_err(&i2c->dev, "Failed to read device ID: %d\n", ret); |
| return ret; |
| } |
| if (val != 0x58) { |
| dev_err(&i2c->dev, "Manufacturer ID %x != 0x58\n", val); |
| return -EINVAL; |
| } |
| |
| ret = regmap_read(regmap, MP8859_IC_REV_REG, &rev); |
| if (ret != 0) { |
| dev_err(&i2c->dev, "Failed to read device revision: %d\n", ret); |
| return ret; |
| } |
| ret = regmap_read(regmap, MP8859_ID1_REG, &val); |
| if (ret != 0) { |
| dev_err(&i2c->dev, "Failed to read device ID1: %d\n", ret); |
| return ret; |
| } |
| dev_info(&i2c->dev, "MP8859-%04d revision %d\n", val, rev); |
| |
| rdev = devm_regulator_register(&i2c->dev, &mp8859_regulators[0], |
| &config); |
| |
| if (IS_ERR(rdev)) { |
| ret = PTR_ERR(rdev); |
| dev_err(&i2c->dev, "failed to register %s: %d\n", |
| mp8859_regulators[0].name, ret); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static const struct of_device_id mp8859_dt_id[] __maybe_unused = { |
| {.compatible = "mps,mp8859"}, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, mp8859_dt_id); |
| |
| static const struct i2c_device_id mp8859_i2c_id[] = { |
| { "mp8859", }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(i2c, mp8859_i2c_id); |
| |
| static struct i2c_driver mp8859_regulator_driver = { |
| .driver = { |
| .name = "mp8859", |
| .probe_type = PROBE_PREFER_ASYNCHRONOUS, |
| .of_match_table = of_match_ptr(mp8859_dt_id), |
| }, |
| .probe = mp8859_i2c_probe, |
| .id_table = mp8859_i2c_id, |
| }; |
| |
| module_i2c_driver(mp8859_regulator_driver); |
| |
| MODULE_DESCRIPTION("Monolithic Power Systems MP8859 voltage regulator driver"); |
| MODULE_AUTHOR("Markus Reichl <m.reichl@fivetechno.de>"); |
| MODULE_LICENSE("GPL v2"); |