include/media/v4l2-mediabus.h - linux - Git at Google

 /* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * Media Bus API header
  *
  * Copyright (C) 2009, Guennadi Liakhovetski <g.liakhovetski@gmx.de>
  */

 #ifndef V4L2_MEDIABUS_H
 #define V4L2_MEDIABUS_H

 #include <linux/v4l2-mediabus.h>
 #include <linux/bitops.h>

 /*
  * How to use the V4L2_MBUS_* flags:
  * Flags are defined for each of the possible states and values of a media
  * bus configuration parameter. One and only one bit of each group of flags
  * shall be set by the users of the v4l2_subdev_pad_ops.get_mbus_config
  * operation to ensure that no conflicting settings are specified when
  * reporting the media bus configuration. For example, it is invalid to set or
  * clear both the V4L2_MBUS_HSYNC_ACTIVE_HIGH and the
  * V4L2_MBUS_HSYNC_ACTIVE_LOW flag at the same time. Instead either flag
  * V4L2_MBUS_HSYNC_ACTIVE_HIGH or flag V4L2_MBUS_HSYNC_ACTIVE_LOW shall be set.
  *
  * TODO: replace the existing V4L2_MBUS_* flags with structures of fields
  * to avoid conflicting settings.
  *
  * In example:
  *     #define V4L2_MBUS_HSYNC_ACTIVE_HIGH             BIT(2)
  *     #define V4L2_MBUS_HSYNC_ACTIVE_LOW              BIT(3)
  * will be replaced by a field whose value reports the intended active state of
  * the signal:
  *     unsigned int v4l2_mbus_hsync_active : 1;
  */

 /* Parallel flags */
 /*
  * The client runs in master or in slave mode. By "Master mode" an operation
  * mode is meant, when the client (e.g., a camera sensor) is producing
  * horizontal and vertical synchronisation. In "Slave mode" the host is
  * providing these signals to the slave.
  */
 #define V4L2_MBUS_MASTER			BIT(0)
 #define V4L2_MBUS_SLAVE				BIT(1)
 /*
  * Signal polarity flags
  * Note: in BT.656 mode HSYNC, FIELD, and VSYNC are unused
  * V4L2_MBUS_[HV]SYNC* flags should be also used for specifying
  * configuration of hardware that uses [HV]REF signals
  */
 #define V4L2_MBUS_HSYNC_ACTIVE_HIGH		BIT(2)
 #define V4L2_MBUS_HSYNC_ACTIVE_LOW		BIT(3)
 #define V4L2_MBUS_VSYNC_ACTIVE_HIGH		BIT(4)
 #define V4L2_MBUS_VSYNC_ACTIVE_LOW		BIT(5)
 #define V4L2_MBUS_PCLK_SAMPLE_RISING		BIT(6)
 #define V4L2_MBUS_PCLK_SAMPLE_FALLING		BIT(7)
 #define V4L2_MBUS_PCLK_SAMPLE_DUALEDGE		BIT(8)
 #define V4L2_MBUS_DATA_ACTIVE_HIGH		BIT(9)
 #define V4L2_MBUS_DATA_ACTIVE_LOW		BIT(10)
 /* FIELD = 0/1 - Field1 (odd)/Field2 (even) */
 #define V4L2_MBUS_FIELD_EVEN_HIGH		BIT(11)
 /* FIELD = 1/0 - Field1 (odd)/Field2 (even) */
 #define V4L2_MBUS_FIELD_EVEN_LOW		BIT(12)
 /* Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively. */
 #define V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH		BIT(13)
 #define V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW		BIT(14)
 #define V4L2_MBUS_DATA_ENABLE_HIGH		BIT(15)
 #define V4L2_MBUS_DATA_ENABLE_LOW		BIT(16)

 /* Serial flags */
 /* Clock non-continuous mode support. */
 #define V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK	BIT(0)

 #define V4L2_MBUS_CSI2_MAX_DATA_LANES		8

 /**
  * struct v4l2_mbus_config_mipi_csi2 - MIPI CSI-2 data bus configuration
  * @flags: media bus (V4L2_MBUS_*) flags
  * @data_lanes: an array of physical data lane indexes
  * @clock_lane: physical lane index of the clock lane
  * @num_data_lanes: number of data lanes
  * @lane_polarities: polarity of the lanes. The order is the same of
  *		   the physical lanes.
  */
 struct v4l2_mbus_config_mipi_csi2 {
 	unsigned int flags;
 	unsigned char data_lanes[V4L2_MBUS_CSI2_MAX_DATA_LANES];
 	unsigned char clock_lane;
 	unsigned char num_data_lanes;
 	bool lane_polarities[1 + V4L2_MBUS_CSI2_MAX_DATA_LANES];
 };

 /**
  * struct v4l2_mbus_config_parallel - parallel data bus configuration
  * @flags: media bus (V4L2_MBUS_*) flags
  * @bus_width: bus width in bits
  * @data_shift: data shift in bits
  */
 struct v4l2_mbus_config_parallel {
 	unsigned int flags;
 	unsigned char bus_width;
 	unsigned char data_shift;
 };

 /**
  * struct v4l2_mbus_config_mipi_csi1 - CSI-1/CCP2 data bus configuration
  * @clock_inv: polarity of clock/strobe signal
  *	       false - not inverted, true - inverted
  * @strobe: false - data/clock, true - data/strobe
  * @lane_polarity: the polarities of the clock (index 0) and data lanes
  *		   index (1)
  * @data_lane: the number of the data lane
  * @clock_lane: the number of the clock lane
  */
 struct v4l2_mbus_config_mipi_csi1 {
 	unsigned char clock_inv:1;
 	unsigned char strobe:1;
 	bool lane_polarity[2];
 	unsigned char data_lane;
 	unsigned char clock_lane;
 };

 /**
  * enum v4l2_mbus_type - media bus type
  * @V4L2_MBUS_UNKNOWN:	unknown bus type, no V4L2 mediabus configuration
  * @V4L2_MBUS_PARALLEL:	parallel interface with hsync and vsync
  * @V4L2_MBUS_BT656:	parallel interface with embedded synchronisation, can
  *			also be used for BT.1120
  * @V4L2_MBUS_CSI1:	MIPI CSI-1 serial interface
  * @V4L2_MBUS_CCP2:	CCP2 (Compact Camera Port 2)
  * @V4L2_MBUS_CSI2_DPHY: MIPI CSI-2 serial interface, with D-PHY
  * @V4L2_MBUS_CSI2_CPHY: MIPI CSI-2 serial interface, with C-PHY
  * @V4L2_MBUS_DPI:      MIPI VIDEO DPI interface
  * @V4L2_MBUS_INVALID:	invalid bus type (keep as last)
  */
 enum v4l2_mbus_type {
 	V4L2_MBUS_UNKNOWN,
 	V4L2_MBUS_PARALLEL,
 	V4L2_MBUS_BT656,
 	V4L2_MBUS_CSI1,
 	V4L2_MBUS_CCP2,
 	V4L2_MBUS_CSI2_DPHY,
 	V4L2_MBUS_CSI2_CPHY,
 	V4L2_MBUS_DPI,
 	V4L2_MBUS_INVALID,
 };

 /**
  * struct v4l2_mbus_config - media bus configuration
  * @type: interface type
  * @bus: bus configuration data structure
  * @bus.parallel: embedded &struct v4l2_mbus_config_parallel.
  *		  Used if the bus is parallel or BT.656.
  * @bus.mipi_csi1: embedded &struct v4l2_mbus_config_mipi_csi1.
  *		   Used if the bus is MIPI Alliance's Camera Serial
  *		   Interface version 1 (MIPI CSI1) or Standard
  *		   Mobile Imaging Architecture's Compact Camera Port 2
  *		   (SMIA CCP2).
  * @bus.mipi_csi2: embedded &struct v4l2_mbus_config_mipi_csi2.
  *		   Used if the bus is MIPI Alliance's Camera Serial
  *		   Interface version 2 (MIPI CSI2).
  */
 struct v4l2_mbus_config {
 	enum v4l2_mbus_type type;
 	union {
 		struct v4l2_mbus_config_parallel parallel;
 		struct v4l2_mbus_config_mipi_csi1 mipi_csi1;
 		struct v4l2_mbus_config_mipi_csi2 mipi_csi2;
 	} bus;
 };

 /**
  * v4l2_fill_pix_format - Ancillary routine that fills a &struct
  *	v4l2_pix_format fields from a &struct v4l2_mbus_framefmt.
  *
  * @pix_fmt:	pointer to &struct v4l2_pix_format to be filled
  * @mbus_fmt:	pointer to &struct v4l2_mbus_framefmt to be used as model
  */
 static inline void
 v4l2_fill_pix_format(struct v4l2_pix_format *pix_fmt,
 		     const struct v4l2_mbus_framefmt *mbus_fmt)
 {
 	pix_fmt->width = mbus_fmt->width;
 	pix_fmt->height = mbus_fmt->height;
 	pix_fmt->field = mbus_fmt->field;
 	pix_fmt->colorspace = mbus_fmt->colorspace;
 	pix_fmt->ycbcr_enc = mbus_fmt->ycbcr_enc;
 	pix_fmt->quantization = mbus_fmt->quantization;
 	pix_fmt->xfer_func = mbus_fmt->xfer_func;
 }

 /**
  * v4l2_fill_mbus_format - Ancillary routine that fills a &struct
  *	v4l2_mbus_framefmt from a &struct v4l2_pix_format and a
  *	data format code.
  *
  * @mbus_fmt:	pointer to &struct v4l2_mbus_framefmt to be filled
  * @pix_fmt:	pointer to &struct v4l2_pix_format to be used as model
  * @code:	data format code (from &enum v4l2_mbus_pixelcode)
  */
 static inline void v4l2_fill_mbus_format(struct v4l2_mbus_framefmt *mbus_fmt,
 					 const struct v4l2_pix_format *pix_fmt,
 			   u32 code)
 {
 	mbus_fmt->width = pix_fmt->width;
 	mbus_fmt->height = pix_fmt->height;
 	mbus_fmt->field = pix_fmt->field;
 	mbus_fmt->colorspace = pix_fmt->colorspace;
 	mbus_fmt->ycbcr_enc = pix_fmt->ycbcr_enc;
 	mbus_fmt->quantization = pix_fmt->quantization;
 	mbus_fmt->xfer_func = pix_fmt->xfer_func;
 	mbus_fmt->code = code;
 }

 /**
  * v4l2_fill_pix_format_mplane - Ancillary routine that fills a &struct
  *	v4l2_pix_format_mplane fields from a media bus structure.
  *
  * @pix_mp_fmt:	pointer to &struct v4l2_pix_format_mplane to be filled
  * @mbus_fmt:	pointer to &struct v4l2_mbus_framefmt to be used as model
  */
 static inline void
 v4l2_fill_pix_format_mplane(struct v4l2_pix_format_mplane *pix_mp_fmt,
 			    const struct v4l2_mbus_framefmt *mbus_fmt)
 {
 	pix_mp_fmt->width = mbus_fmt->width;
 	pix_mp_fmt->height = mbus_fmt->height;
 	pix_mp_fmt->field = mbus_fmt->field;
 	pix_mp_fmt->colorspace = mbus_fmt->colorspace;
 	pix_mp_fmt->ycbcr_enc = mbus_fmt->ycbcr_enc;
 	pix_mp_fmt->quantization = mbus_fmt->quantization;
 	pix_mp_fmt->xfer_func = mbus_fmt->xfer_func;
 }

 /**
  * v4l2_fill_mbus_format_mplane - Ancillary routine that fills a &struct
  *	v4l2_mbus_framefmt from a &struct v4l2_pix_format_mplane.
  *
  * @mbus_fmt:	pointer to &struct v4l2_mbus_framefmt to be filled
  * @pix_mp_fmt:	pointer to &struct v4l2_pix_format_mplane to be used as model
  */
 static inline void
 v4l2_fill_mbus_format_mplane(struct v4l2_mbus_framefmt *mbus_fmt,
 			     const struct v4l2_pix_format_mplane *pix_mp_fmt)
 {
 	mbus_fmt->width = pix_mp_fmt->width;
 	mbus_fmt->height = pix_mp_fmt->height;
 	mbus_fmt->field = pix_mp_fmt->field;
 	mbus_fmt->colorspace = pix_mp_fmt->colorspace;
 	mbus_fmt->ycbcr_enc = pix_mp_fmt->ycbcr_enc;
 	mbus_fmt->quantization = pix_mp_fmt->quantization;
 	mbus_fmt->xfer_func = pix_mp_fmt->xfer_func;
 }

 #endif
	/* SPDX-License-Identifier: GPL-2.0-only */
	/*
	* Media Bus API header
	*
	* Copyright (C) 2009, Guennadi Liakhovetski <g.liakhovetski@gmx.de>
	*/

	#ifndef V4L2_MEDIABUS_H
	#define V4L2_MEDIABUS_H

	#include <linux/v4l2-mediabus.h>
	#include <linux/bitops.h>

	/*
	* How to use the V4L2_MBUS_* flags:
	* Flags are defined for each of the possible states and values of a media
	* bus configuration parameter. One and only one bit of each group of flags
	* shall be set by the users of the v4l2_subdev_pad_ops.get_mbus_config
	* operation to ensure that no conflicting settings are specified when
	* reporting the media bus configuration. For example, it is invalid to set or
	* clear both the V4L2_MBUS_HSYNC_ACTIVE_HIGH and the
	* V4L2_MBUS_HSYNC_ACTIVE_LOW flag at the same time. Instead either flag
	* V4L2_MBUS_HSYNC_ACTIVE_HIGH or flag V4L2_MBUS_HSYNC_ACTIVE_LOW shall be set.
	*
	* TODO: replace the existing V4L2_MBUS_* flags with structures of fields
	* to avoid conflicting settings.
	*
	* In example:
	* #define V4L2_MBUS_HSYNC_ACTIVE_HIGH BIT(2)
	* #define V4L2_MBUS_HSYNC_ACTIVE_LOW BIT(3)
	* will be replaced by a field whose value reports the intended active state of
	* the signal:
	* unsigned int v4l2_mbus_hsync_active : 1;
	*/

	/* Parallel flags */
	/*
	* The client runs in master or in slave mode. By "Master mode" an operation
	* mode is meant, when the client (e.g., a camera sensor) is producing
	* horizontal and vertical synchronisation. In "Slave mode" the host is
	* providing these signals to the slave.
	*/
	#define V4L2_MBUS_MASTER BIT(0)
	#define V4L2_MBUS_SLAVE BIT(1)
	/*
	* Signal polarity flags
	* Note: in BT.656 mode HSYNC, FIELD, and VSYNC are unused
	* V4L2_MBUS_[HV]SYNC* flags should be also used for specifying
	* configuration of hardware that uses [HV]REF signals
	*/
	#define V4L2_MBUS_HSYNC_ACTIVE_HIGH BIT(2)
	#define V4L2_MBUS_HSYNC_ACTIVE_LOW BIT(3)
	#define V4L2_MBUS_VSYNC_ACTIVE_HIGH BIT(4)
	#define V4L2_MBUS_VSYNC_ACTIVE_LOW BIT(5)
	#define V4L2_MBUS_PCLK_SAMPLE_RISING BIT(6)
	#define V4L2_MBUS_PCLK_SAMPLE_FALLING BIT(7)
	#define V4L2_MBUS_PCLK_SAMPLE_DUALEDGE BIT(8)
	#define V4L2_MBUS_DATA_ACTIVE_HIGH BIT(9)
	#define V4L2_MBUS_DATA_ACTIVE_LOW BIT(10)
	/* FIELD = 0/1 - Field1 (odd)/Field2 (even) */
	#define V4L2_MBUS_FIELD_EVEN_HIGH BIT(11)
	/* FIELD = 1/0 - Field1 (odd)/Field2 (even) */
	#define V4L2_MBUS_FIELD_EVEN_LOW BIT(12)
	/* Active state of Sync-on-green (SoG) signal, 0/1 for LOW/HIGH respectively. */
	#define V4L2_MBUS_VIDEO_SOG_ACTIVE_HIGH BIT(13)
	#define V4L2_MBUS_VIDEO_SOG_ACTIVE_LOW BIT(14)
	#define V4L2_MBUS_DATA_ENABLE_HIGH BIT(15)
	#define V4L2_MBUS_DATA_ENABLE_LOW BIT(16)

	/* Serial flags */
	/* Clock non-continuous mode support. */
	#define V4L2_MBUS_CSI2_NONCONTINUOUS_CLOCK BIT(0)

	#define V4L2_MBUS_CSI2_MAX_DATA_LANES 8

	/**
	* struct v4l2_mbus_config_mipi_csi2 - MIPI CSI-2 data bus configuration
	* @flags: media bus (V4L2_MBUS_*) flags
	* @data_lanes: an array of physical data lane indexes
	* @clock_lane: physical lane index of the clock lane
	* @num_data_lanes: number of data lanes
	* @lane_polarities: polarity of the lanes. The order is the same of
	* the physical lanes.
	*/
	struct v4l2_mbus_config_mipi_csi2 {
	unsigned int flags;
	unsigned char data_lanes[V4L2_MBUS_CSI2_MAX_DATA_LANES];
	unsigned char clock_lane;
	unsigned char num_data_lanes;
	bool lane_polarities[1 + V4L2_MBUS_CSI2_MAX_DATA_LANES];
	};

	/**
	* struct v4l2_mbus_config_parallel - parallel data bus configuration
	* @flags: media bus (V4L2_MBUS_*) flags
	* @bus_width: bus width in bits
	* @data_shift: data shift in bits
	*/
	struct v4l2_mbus_config_parallel {
	unsigned int flags;
	unsigned char bus_width;
	unsigned char data_shift;
	};

	/**
	* struct v4l2_mbus_config_mipi_csi1 - CSI-1/CCP2 data bus configuration
	* @clock_inv: polarity of clock/strobe signal
	* false - not inverted, true - inverted
	* @strobe: false - data/clock, true - data/strobe
	* @lane_polarity: the polarities of the clock (index 0) and data lanes
	* index (1)
	* @data_lane: the number of the data lane
	* @clock_lane: the number of the clock lane
	*/
	struct v4l2_mbus_config_mipi_csi1 {
	unsigned char clock_inv:1;
	unsigned char strobe:1;
	bool lane_polarity[2];
	unsigned char data_lane;
	unsigned char clock_lane;
	};

	/**
	* enum v4l2_mbus_type - media bus type
	* @V4L2_MBUS_UNKNOWN: unknown bus type, no V4L2 mediabus configuration
	* @V4L2_MBUS_PARALLEL: parallel interface with hsync and vsync
	* @V4L2_MBUS_BT656: parallel interface with embedded synchronisation, can
	* also be used for BT.1120
	* @V4L2_MBUS_CSI1: MIPI CSI-1 serial interface
	* @V4L2_MBUS_CCP2: CCP2 (Compact Camera Port 2)
	* @V4L2_MBUS_CSI2_DPHY: MIPI CSI-2 serial interface, with D-PHY
	* @V4L2_MBUS_CSI2_CPHY: MIPI CSI-2 serial interface, with C-PHY
	* @V4L2_MBUS_DPI: MIPI VIDEO DPI interface
	* @V4L2_MBUS_INVALID: invalid bus type (keep as last)
	*/
	enum v4l2_mbus_type {
	V4L2_MBUS_UNKNOWN,
	V4L2_MBUS_PARALLEL,
	V4L2_MBUS_BT656,
	V4L2_MBUS_CSI1,
	V4L2_MBUS_CCP2,
	V4L2_MBUS_CSI2_DPHY,
	V4L2_MBUS_CSI2_CPHY,
	V4L2_MBUS_DPI,
	V4L2_MBUS_INVALID,
	};

	/**
	* struct v4l2_mbus_config - media bus configuration
	* @type: interface type
	* @bus: bus configuration data structure
	* @bus.parallel: embedded &struct v4l2_mbus_config_parallel.
	* Used if the bus is parallel or BT.656.
	* @bus.mipi_csi1: embedded &struct v4l2_mbus_config_mipi_csi1.
	* Used if the bus is MIPI Alliance's Camera Serial
	* Interface version 1 (MIPI CSI1) or Standard
	* Mobile Imaging Architecture's Compact Camera Port 2
	* (SMIA CCP2).
	* @bus.mipi_csi2: embedded &struct v4l2_mbus_config_mipi_csi2.
	* Used if the bus is MIPI Alliance's Camera Serial
	* Interface version 2 (MIPI CSI2).
	*/
	struct v4l2_mbus_config {
	enum v4l2_mbus_type type;
	union {
	struct v4l2_mbus_config_parallel parallel;
	struct v4l2_mbus_config_mipi_csi1 mipi_csi1;
	struct v4l2_mbus_config_mipi_csi2 mipi_csi2;
	} bus;
	};

	/**
	* v4l2_fill_pix_format - Ancillary routine that fills a &struct
	* v4l2_pix_format fields from a &struct v4l2_mbus_framefmt.
	*
	* @pix_fmt: pointer to &struct v4l2_pix_format to be filled
	* @mbus_fmt: pointer to &struct v4l2_mbus_framefmt to be used as model
	*/
	static inline void
	v4l2_fill_pix_format(struct v4l2_pix_format *pix_fmt,
	const struct v4l2_mbus_framefmt *mbus_fmt)
	{
	pix_fmt->width = mbus_fmt->width;
	pix_fmt->height = mbus_fmt->height;
	pix_fmt->field = mbus_fmt->field;
	pix_fmt->colorspace = mbus_fmt->colorspace;
	pix_fmt->ycbcr_enc = mbus_fmt->ycbcr_enc;
	pix_fmt->quantization = mbus_fmt->quantization;
	pix_fmt->xfer_func = mbus_fmt->xfer_func;
	}

	/**
	* v4l2_fill_mbus_format - Ancillary routine that fills a &struct
	* v4l2_mbus_framefmt from a &struct v4l2_pix_format and a
	* data format code.
	*
	* @mbus_fmt: pointer to &struct v4l2_mbus_framefmt to be filled
	* @pix_fmt: pointer to &struct v4l2_pix_format to be used as model
	* @code: data format code (from &enum v4l2_mbus_pixelcode)
	*/
	static inline void v4l2_fill_mbus_format(struct v4l2_mbus_framefmt *mbus_fmt,
	const struct v4l2_pix_format *pix_fmt,
	u32 code)
	{
	mbus_fmt->width = pix_fmt->width;
	mbus_fmt->height = pix_fmt->height;
	mbus_fmt->field = pix_fmt->field;
	mbus_fmt->colorspace = pix_fmt->colorspace;
	mbus_fmt->ycbcr_enc = pix_fmt->ycbcr_enc;
	mbus_fmt->quantization = pix_fmt->quantization;
	mbus_fmt->xfer_func = pix_fmt->xfer_func;
	mbus_fmt->code = code;
	}

	/**
	* v4l2_fill_pix_format_mplane - Ancillary routine that fills a &struct
	* v4l2_pix_format_mplane fields from a media bus structure.
	*
	* @pix_mp_fmt: pointer to &struct v4l2_pix_format_mplane to be filled
	* @mbus_fmt: pointer to &struct v4l2_mbus_framefmt to be used as model
	*/
	static inline void
	v4l2_fill_pix_format_mplane(struct v4l2_pix_format_mplane *pix_mp_fmt,
	const struct v4l2_mbus_framefmt *mbus_fmt)
	{
	pix_mp_fmt->width = mbus_fmt->width;
	pix_mp_fmt->height = mbus_fmt->height;
	pix_mp_fmt->field = mbus_fmt->field;
	pix_mp_fmt->colorspace = mbus_fmt->colorspace;
	pix_mp_fmt->ycbcr_enc = mbus_fmt->ycbcr_enc;
	pix_mp_fmt->quantization = mbus_fmt->quantization;
	pix_mp_fmt->xfer_func = mbus_fmt->xfer_func;
	}

	/**
	* v4l2_fill_mbus_format_mplane - Ancillary routine that fills a &struct
	* v4l2_mbus_framefmt from a &struct v4l2_pix_format_mplane.
	*
	* @mbus_fmt: pointer to &struct v4l2_mbus_framefmt to be filled
	* @pix_mp_fmt: pointer to &struct v4l2_pix_format_mplane to be used as model
	*/
	static inline void
	v4l2_fill_mbus_format_mplane(struct v4l2_mbus_framefmt *mbus_fmt,
	const struct v4l2_pix_format_mplane *pix_mp_fmt)
	{
	mbus_fmt->width = pix_mp_fmt->width;
	mbus_fmt->height = pix_mp_fmt->height;
	mbus_fmt->field = pix_mp_fmt->field;
	mbus_fmt->colorspace = pix_mp_fmt->colorspace;
	mbus_fmt->ycbcr_enc = pix_mp_fmt->ycbcr_enc;
	mbus_fmt->quantization = pix_mp_fmt->quantization;
	mbus_fmt->xfer_func = pix_mp_fmt->xfer_func;
	}

	#endif