| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz> |
| * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi> |
| */ |
| |
| /dts-v1/; |
| |
| #include "omap34xx.dtsi" |
| #include <dt-bindings/input/input.h> |
| |
| /* |
| * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall |
| * for omap AES HW crypto support. When linux kernel try to access memory of AES |
| * blocks then kernel receive "Unhandled fault: external abort on non-linefetch" |
| * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no |
| * crash anymore) omap AES support will be disabled for all Nokia N900 devices. |
| * There is "unofficial" version of bootloader which enables AES in L3 firewall |
| * but it is not widely used and to prevent kernel crash rather AES is disabled. |
| * There is also no runtime detection code if AES is disabled in L3 firewall... |
| */ |
| &aes { |
| status = "disabled"; |
| }; |
| |
| / { |
| model = "Nokia N900"; |
| compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3"; |
| |
| aliases { |
| i2c0; |
| i2c1 = &i2c1; |
| i2c2 = &i2c2; |
| i2c3 = &i2c3; |
| display0 = &lcd; |
| display1 = &tv; |
| }; |
| |
| cpus { |
| cpu@0 { |
| cpu0-supply = <&vcc>; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| heartbeat { |
| label = "debug::sleep"; |
| gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* 162 */ |
| linux,default-trigger = "default-on"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&debug_leds>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| reg = <0x80000000 0x10000000>; /* 256 MB */ |
| }; |
| |
| gpio_keys { |
| compatible = "gpio-keys"; |
| |
| camera_lens_cover { |
| label = "Camera Lens Cover"; |
| gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */ |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_CAMERA_LENS_COVER>; |
| linux,can-disable; |
| }; |
| |
| camera_focus { |
| label = "Camera Focus"; |
| gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */ |
| linux,code = <KEY_CAMERA_FOCUS>; |
| linux,can-disable; |
| }; |
| |
| camera_capture { |
| label = "Camera Capture"; |
| gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */ |
| linux,code = <KEY_CAMERA>; |
| linux,can-disable; |
| }; |
| |
| lock_button { |
| label = "Lock Button"; |
| gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */ |
| linux,code = <KEY_SCREENLOCK>; |
| linux,can-disable; |
| }; |
| |
| keypad_slide { |
| label = "Keypad Slide"; |
| gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */ |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_KEYPAD_SLIDE>; |
| linux,can-disable; |
| }; |
| |
| proximity_sensor { |
| label = "Proximity Sensor"; |
| gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */ |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_FRONT_PROXIMITY>; |
| linux,can-disable; |
| }; |
| }; |
| |
| isp1707: isp1707 { |
| compatible = "nxp,isp1707"; |
| nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>; |
| usb-phy = <&usb2_phy>; |
| }; |
| |
| tv: connector { |
| compatible = "composite-video-connector"; |
| label = "tv"; |
| |
| port { |
| tv_connector_in: endpoint { |
| remote-endpoint = <&venc_out>; |
| }; |
| }; |
| }; |
| |
| sound: n900-audio { |
| compatible = "nokia,n900-audio"; |
| |
| nokia,cpu-dai = <&mcbsp2>; |
| nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>; |
| nokia,headphone-amplifier = <&tpa6130a2>; |
| |
| tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */ |
| jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */ |
| eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */ |
| speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| battery: n900-battery { |
| compatible = "nokia,n900-battery"; |
| io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>; |
| io-channel-names = "temp", "bsi", "vbat"; |
| }; |
| |
| pwm9: dmtimer-pwm { |
| compatible = "ti,omap-dmtimer-pwm"; |
| #pwm-cells = <3>; |
| ti,timers = <&timer9>; |
| ti,clock-source = <0x00>; /* timer_sys_ck */ |
| }; |
| |
| ir: n900-ir { |
| compatible = "nokia,n900-ir"; |
| pwms = <&pwm9 0 26316 0>; /* 38000 Hz */ |
| }; |
| |
| rom_rng: rng { |
| compatible = "nokia,n900-rom-rng"; |
| clocks = <&rng_ick>; |
| clock-names = "ick"; |
| }; |
| |
| /* controlled (enabled/disabled) directly by bcm2048 and wl1251 */ |
| vctcxo: vctcxo { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <38400000>; |
| }; |
| }; |
| |
| &isp { |
| vdds_csib-supply = <&vaux2>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&camera_pins>; |
| |
| ports { |
| port@1 { |
| reg = <1>; |
| |
| csi_isp: endpoint { |
| remote-endpoint = <&csi_cam1>; |
| bus-type = <3>; /* CCP2 */ |
| clock-lanes = <1>; |
| data-lanes = <0>; |
| lane-polarity = <0 0>; |
| /* Select strobe = <1> for back camera, <0> for front camera */ |
| strobe = <1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| pinctrl-names = "default"; |
| |
| uart2_pins: pinmux_uart2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */ |
| OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */ |
| OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */ |
| OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */ |
| >; |
| }; |
| |
| uart3_pins: pinmux_uart3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */ |
| OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */ |
| >; |
| }; |
| |
| ethernet_pins: pinmux_ethernet_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */ |
| OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */ |
| OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */ |
| >; |
| }; |
| |
| gpmc_pins: pinmux_gpmc_pins { |
| pinctrl-single,pins = < |
| |
| /* address lines */ |
| OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */ |
| OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */ |
| OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */ |
| |
| /* data lines, gpmc_d0..d7 not muxable according to TRM */ |
| OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */ |
| OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */ |
| OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */ |
| OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */ |
| OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */ |
| OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */ |
| OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */ |
| OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */ |
| |
| /* |
| * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable |
| * according to TRM. OneNAND seems to require PIN_INPUT on clock. |
| */ |
| OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */ |
| OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */ |
| >; |
| }; |
| |
| i2c1_pins: pinmux_i2c1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */ |
| OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */ |
| >; |
| }; |
| |
| i2c2_pins: pinmux_i2c2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */ |
| OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */ |
| >; |
| }; |
| |
| i2c3_pins: pinmux_i2c3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */ |
| OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */ |
| >; |
| }; |
| |
| debug_leds: pinmux_debug_led_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */ |
| >; |
| }; |
| |
| mcspi4_pins: pinmux_mcspi4_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */ |
| OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */ |
| OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */ |
| OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */ |
| >; |
| }; |
| |
| mmc1_pins: pinmux_mmc1_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ |
| OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */ |
| OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */ |
| OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ |
| OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ |
| OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ |
| >; |
| }; |
| |
| mmc2_pins: pinmux_mmc2_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */ |
| OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */ |
| OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */ |
| OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */ |
| OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */ |
| OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */ |
| OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */ |
| OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */ |
| >; |
| }; |
| |
| acx565akm_pins: pinmux_acx565akm_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */ |
| >; |
| }; |
| |
| dss_sdi_pins: pinmux_dss_sdi_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */ |
| OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */ |
| OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */ |
| OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */ |
| |
| OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */ |
| OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */ |
| >; |
| }; |
| |
| wl1251_pins: pinmux_wl1251 { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */ |
| OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */ |
| >; |
| }; |
| |
| ssi_pins: pinmux_ssi { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */ |
| OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */ |
| OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4) /* ssi1_wake_tx (cawake) */ |
| OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */ |
| OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */ |
| OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */ |
| OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */ |
| OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */ |
| >; |
| }; |
| |
| modem_pins: pinmux_modem { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */ |
| OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4) /* gpio 72 => ape_rst_rq */ |
| OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */ |
| OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */ |
| OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */ |
| OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */ |
| >; |
| }; |
| |
| camera_pins: pinmux_camera { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7) /* cam_hs */ |
| OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7) /* cam_vs */ |
| OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE0) /* cam_xclka */ |
| OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE7) /* cam_d4 */ |
| OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6 */ |
| OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7 */ |
| OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE0) /* cam_d8 */ |
| OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE0) /* cam_d9 */ |
| OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE7) /* cam_d10 */ |
| OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT | MUX_MODE7) /* cam_xclkb */ |
| OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE0) /* cam_strobe */ |
| >; |
| }; |
| }; |
| |
| &i2c1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c1_pins>; |
| |
| clock-frequency = <2200000>; |
| |
| twl: twl@48 { |
| reg = <0x48>; |
| interrupts = <7>; /* SYS_NIRQ cascaded to intc */ |
| interrupt-parent = <&intc>; |
| }; |
| }; |
| |
| #include "twl4030.dtsi" |
| #include "twl4030_omap3.dtsi" |
| |
| &vaux1 { |
| regulator-name = "V28"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| regulator-always-on; /* due to battery cover sensor */ |
| }; |
| |
| &vaux2 { |
| regulator-name = "VCSI"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| }; |
| |
| &vaux3 { |
| regulator-name = "VMMC2_30"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| }; |
| |
| &vaux4 { |
| regulator-name = "VCAM_ANA_28"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| }; |
| |
| &vmmc1 { |
| regulator-name = "VMMC1"; |
| regulator-min-microvolt = <1850000>; |
| regulator-max-microvolt = <3150000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| }; |
| |
| &vmmc2 { |
| regulator-name = "V28_A"; |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <3000000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| regulator-always-on; /* due VIO leak to AIC34 VDDs */ |
| }; |
| |
| &vpll1 { |
| regulator-name = "VPLL"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| regulator-always-on; |
| }; |
| |
| &vpll2 { |
| regulator-name = "VSDI_CSI"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| regulator-always-on; |
| }; |
| |
| &vsim { |
| regulator-name = "VMMC2_IO_18"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */ |
| }; |
| |
| &vio { |
| regulator-name = "VIO"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| &vintana1 { |
| regulator-name = "VINTANA1"; |
| /* fixed to 1500000 */ |
| regulator-always-on; |
| }; |
| |
| &vintana2 { |
| regulator-name = "VINTANA2"; |
| regulator-min-microvolt = <2750000>; |
| regulator-max-microvolt = <2750000>; |
| regulator-always-on; |
| }; |
| |
| &vintdig { |
| regulator-name = "VINTDIG"; |
| /* fixed to 1500000 */ |
| regulator-always-on; |
| }; |
| |
| /* First two dma channels are reserved on secure omap3 */ |
| &sdma { |
| dma-channel-mask = <0xfffffffc>; |
| }; |
| |
| &twl { |
| twl_audio: audio { |
| compatible = "ti,twl4030-audio"; |
| ti,enable-vibra = <1>; |
| }; |
| |
| twl_power: power { |
| compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off"; |
| ti,use_poweroff; |
| }; |
| }; |
| |
| &twl_keypad { |
| linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q) |
| MATRIX_KEY(0x00, 0x01, KEY_O) |
| MATRIX_KEY(0x00, 0x02, KEY_P) |
| MATRIX_KEY(0x00, 0x03, KEY_COMMA) |
| MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE) |
| MATRIX_KEY(0x00, 0x06, KEY_A) |
| MATRIX_KEY(0x00, 0x07, KEY_S) |
| |
| MATRIX_KEY(0x01, 0x00, KEY_W) |
| MATRIX_KEY(0x01, 0x01, KEY_D) |
| MATRIX_KEY(0x01, 0x02, KEY_F) |
| MATRIX_KEY(0x01, 0x03, KEY_G) |
| MATRIX_KEY(0x01, 0x04, KEY_H) |
| MATRIX_KEY(0x01, 0x05, KEY_J) |
| MATRIX_KEY(0x01, 0x06, KEY_K) |
| MATRIX_KEY(0x01, 0x07, KEY_L) |
| |
| MATRIX_KEY(0x02, 0x00, KEY_E) |
| MATRIX_KEY(0x02, 0x01, KEY_DOT) |
| MATRIX_KEY(0x02, 0x02, KEY_UP) |
| MATRIX_KEY(0x02, 0x03, KEY_ENTER) |
| MATRIX_KEY(0x02, 0x05, KEY_Z) |
| MATRIX_KEY(0x02, 0x06, KEY_X) |
| MATRIX_KEY(0x02, 0x07, KEY_C) |
| MATRIX_KEY(0x02, 0x08, KEY_F9) |
| |
| MATRIX_KEY(0x03, 0x00, KEY_R) |
| MATRIX_KEY(0x03, 0x01, KEY_V) |
| MATRIX_KEY(0x03, 0x02, KEY_B) |
| MATRIX_KEY(0x03, 0x03, KEY_N) |
| MATRIX_KEY(0x03, 0x04, KEY_M) |
| MATRIX_KEY(0x03, 0x05, KEY_SPACE) |
| MATRIX_KEY(0x03, 0x06, KEY_SPACE) |
| MATRIX_KEY(0x03, 0x07, KEY_LEFT) |
| |
| MATRIX_KEY(0x04, 0x00, KEY_T) |
| MATRIX_KEY(0x04, 0x01, KEY_DOWN) |
| MATRIX_KEY(0x04, 0x02, KEY_RIGHT) |
| MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL) |
| MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT) |
| MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT) |
| MATRIX_KEY(0x04, 0x08, KEY_F10) |
| |
| MATRIX_KEY(0x05, 0x00, KEY_Y) |
| MATRIX_KEY(0x05, 0x08, KEY_F11) |
| |
| MATRIX_KEY(0x06, 0x00, KEY_U) |
| |
| MATRIX_KEY(0x07, 0x00, KEY_I) |
| MATRIX_KEY(0x07, 0x01, KEY_F7) |
| MATRIX_KEY(0x07, 0x02, KEY_F8) |
| >; |
| }; |
| |
| &twl_gpio { |
| ti,pullups = <0x0>; |
| ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */ |
| }; |
| |
| &i2c2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c2_pins>; |
| |
| clock-frequency = <100000>; |
| |
| tlv320aic3x: tlv320aic3x@18 { |
| compatible = "ti,tlv320aic3x"; |
| reg = <0x18>; |
| reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */ |
| ai3x-gpio-func = < |
| 0 /* AIC3X_GPIO1_FUNC_DISABLED */ |
| 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */ |
| >; |
| |
| AVDD-supply = <&vmmc2>; |
| DRVDD-supply = <&vmmc2>; |
| IOVDD-supply = <&vio>; |
| DVDD-supply = <&vio>; |
| |
| ai3x-micbias-vg = <1>; |
| }; |
| |
| tlv320aic3x_aux: tlv320aic3x@19 { |
| compatible = "ti,tlv320aic3x"; |
| reg = <0x19>; |
| reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */ |
| |
| AVDD-supply = <&vmmc2>; |
| DRVDD-supply = <&vmmc2>; |
| IOVDD-supply = <&vio>; |
| DVDD-supply = <&vio>; |
| |
| ai3x-micbias-vg = <2>; |
| }; |
| |
| tsl2563: tsl2563@29 { |
| compatible = "amstaos,tsl2563"; |
| reg = <0x29>; |
| |
| amstaos,cover-comp-gain = <16>; |
| }; |
| |
| adp1653: led-controller@30 { |
| compatible = "adi,adp1653"; |
| reg = <0x30>; |
| enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */ |
| |
| flash { |
| flash-timeout-us = <500000>; |
| flash-max-microamp = <320000>; |
| led-max-microamp = <50000>; |
| }; |
| indicator { |
| led-max-microamp = <17500>; |
| }; |
| }; |
| |
| lp5523: lp5523@32 { |
| compatible = "national,lp5523"; |
| reg = <0x32>; |
| clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */ |
| enable-gpio = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */ |
| |
| chan0 { |
| chan-name = "lp5523:kb1"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan1 { |
| chan-name = "lp5523:kb2"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan2 { |
| chan-name = "lp5523:kb3"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan3 { |
| chan-name = "lp5523:kb4"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan4 { |
| chan-name = "lp5523:b"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan5 { |
| chan-name = "lp5523:g"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan6 { |
| chan-name = "lp5523:r"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan7 { |
| chan-name = "lp5523:kb5"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| |
| chan8 { |
| chan-name = "lp5523:kb6"; |
| led-cur = /bits/ 8 <50>; |
| max-cur = /bits/ 8 <100>; |
| }; |
| }; |
| |
| bq27200: bq27200@55 { |
| compatible = "ti,bq27200"; |
| reg = <0x55>; |
| power-supplies = <&bq24150a>; |
| }; |
| |
| /* Stereo headphone amplifier */ |
| tpa6130a2: tpa6130a2@60 { |
| compatible = "ti,tpa6130a2"; |
| reg = <0x60>; |
| |
| Vdd-supply = <&vmmc2>; |
| |
| power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */ |
| }; |
| |
| si4713: si4713@63 { |
| compatible = "silabs,si4713"; |
| reg = <0x63>; |
| |
| interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */ |
| reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */ |
| vio-supply = <&vio>; |
| vdd-supply = <&vaux1>; |
| }; |
| |
| bq24150a: bq24150a@6b { |
| compatible = "ti,bq24150a"; |
| reg = <0x6b>; |
| |
| ti,current-limit = <100>; |
| ti,weak-battery-voltage = <3400>; |
| ti,battery-regulation-voltage = <4200>; |
| ti,charge-current = <650>; |
| ti,termination-current = <100>; |
| ti,resistor-sense = <68>; |
| |
| ti,usb-charger-detection = <&isp1707>; |
| }; |
| }; |
| |
| &i2c3 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c3_pins>; |
| |
| clock-frequency = <400000>; |
| |
| lis302dl: lis3lv02d@1d { |
| compatible = "st,lis3lv02d"; |
| reg = <0x1d>; |
| |
| Vdd-supply = <&vaux1>; |
| Vdd_IO-supply = <&vio>; |
| |
| interrupt-parent = <&gpio6>; |
| interrupts = <21 20>; /* 181 and 180 */ |
| |
| /* click flags */ |
| st,click-single-x; |
| st,click-single-y; |
| st,click-single-z; |
| |
| /* Limits are 0.5g * value */ |
| st,click-threshold-x = <8>; |
| st,click-threshold-y = <8>; |
| st,click-threshold-z = <10>; |
| |
| /* Click must be longer than time limit */ |
| st,click-time-limit = <9>; |
| |
| /* Kind of debounce filter */ |
| st,click-latency = <50>; |
| |
| /* Interrupt line 2 for click detection */ |
| st,irq2-click; |
| |
| st,wakeup-x-hi; |
| st,wakeup-y-hi; |
| st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */ |
| |
| st,wakeup2-z-hi; |
| st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */ |
| |
| st,hipass1-disable; |
| st,hipass2-disable; |
| |
| st,axis-x = <1>; /* LIS3_DEV_X */ |
| st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */ |
| st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */ |
| |
| st,min-limit-x = <(-32)>; |
| st,min-limit-y = <3>; |
| st,min-limit-z = <3>; |
| |
| st,max-limit-x = <(-3)>; |
| st,max-limit-y = <32>; |
| st,max-limit-z = <32>; |
| }; |
| |
| cam1: camera@3e { |
| compatible = "toshiba,et8ek8"; |
| reg = <0x3e>; |
| |
| vana-supply = <&vaux4>; |
| |
| clocks = <&isp 0>; |
| clock-names = "extclk"; |
| clock-frequency = <9600000>; |
| |
| reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */ |
| |
| lens-focus = <&ad5820>; |
| |
| port { |
| csi_cam1: endpoint { |
| bus-type = <3>; /* CCP2 */ |
| strobe = <1>; |
| clock-inv = <0>; |
| crc = <1>; |
| |
| remote-endpoint = <&csi_isp>; |
| }; |
| }; |
| }; |
| |
| /* D/A converter for auto-focus */ |
| ad5820: dac@c { |
| compatible = "adi,ad5820"; |
| reg = <0x0c>; |
| |
| VANA-supply = <&vaux4>; |
| |
| #io-channel-cells = <0>; |
| }; |
| }; |
| |
| &mmc1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc1_pins>; |
| vmmc-supply = <&vmmc1>; |
| bus-width = <4>; |
| /* For debugging, it is often good idea to remove this GPIO. |
| It means you can remove back cover (to reboot by removing |
| battery) and still use the MMC card. */ |
| cd-gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */ |
| }; |
| |
| /* most boards use vaux3, only some old versions use vmmc2 instead */ |
| &mmc2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mmc2_pins>; |
| vmmc-supply = <&vaux3>; |
| vqmmc-supply = <&vsim>; |
| bus-width = <8>; |
| non-removable; |
| no-sdio; |
| no-sd; |
| }; |
| |
| &mmc3 { |
| status = "disabled"; |
| }; |
| |
| &gpmc { |
| ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */ |
| <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */ |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpmc_pins>; |
| |
| /* sys_ndmareq1 could be used by the driver, not as gpio65 though */ |
| onenand@0,0 { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "ti,omap2-onenand"; |
| reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */ |
| |
| /* |
| * These timings are based on CONFIG_OMAP_GPMC_DEBUG=y reported |
| * bootloader set values when booted with v5.1 |
| * (OneNAND Manufacturer: Samsung): |
| * |
| * cs0 GPMC_CS_CONFIG1: 0xfb001202 |
| * cs0 GPMC_CS_CONFIG2: 0x00111100 |
| * cs0 GPMC_CS_CONFIG3: 0x00020200 |
| * cs0 GPMC_CS_CONFIG4: 0x11001102 |
| * cs0 GPMC_CS_CONFIG5: 0x03101616 |
| * cs0 GPMC_CS_CONFIG6: 0x90060000 |
| */ |
| gpmc,sync-read; |
| gpmc,sync-write; |
| gpmc,burst-length = <16>; |
| gpmc,burst-read; |
| gpmc,burst-wrap; |
| gpmc,burst-write; |
| gpmc,device-width = <2>; |
| gpmc,mux-add-data = <2>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <102>; |
| gpmc,cs-wr-off-ns = <102>; |
| gpmc,adv-on-ns = <0>; |
| gpmc,adv-rd-off-ns = <12>; |
| gpmc,adv-wr-off-ns = <12>; |
| gpmc,oe-on-ns = <12>; |
| gpmc,oe-off-ns = <102>; |
| gpmc,we-on-ns = <0>; |
| gpmc,we-off-ns = <102>; |
| gpmc,rd-cycle-ns = <132>; |
| gpmc,wr-cycle-ns = <132>; |
| gpmc,access-ns = <96>; |
| gpmc,page-burst-access-ns = <18>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,wait-monitoring-ns = <0>; |
| gpmc,clk-activation-ns = <6>; |
| gpmc,wr-data-mux-bus-ns = <36>; |
| gpmc,wr-access-ns = <96>; |
| gpmc,sync-clk-ps = <15000>; |
| |
| /* |
| * MTD partition table corresponding to Nokia's |
| * Maemo 5 (Fremantle) release. |
| */ |
| partition@0 { |
| label = "bootloader"; |
| reg = <0x00000000 0x00020000>; |
| read-only; |
| }; |
| partition@1 { |
| label = "config"; |
| reg = <0x00020000 0x00060000>; |
| }; |
| partition@2 { |
| label = "log"; |
| reg = <0x00080000 0x00040000>; |
| }; |
| partition@3 { |
| label = "kernel"; |
| reg = <0x000c0000 0x00200000>; |
| }; |
| partition@4 { |
| label = "initfs"; |
| reg = <0x002c0000 0x00200000>; |
| }; |
| partition@5 { |
| label = "rootfs"; |
| reg = <0x004c0000 0x0fb40000>; |
| }; |
| }; |
| |
| /* Ethernet is on some early development boards and qemu */ |
| ethernet@gpmc { |
| compatible = "smsc,lan91c94"; |
| interrupt-parent = <&gpio2>; |
| interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */ |
| reg = <1 0 0xf>; /* 16 byte IO range */ |
| bank-width = <2>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <ðernet_pins>; |
| power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */ |
| reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */ |
| gpmc,device-width = <2>; |
| gpmc,sync-clk-ps = <0>; |
| gpmc,cs-on-ns = <0>; |
| gpmc,cs-rd-off-ns = <48>; |
| gpmc,cs-wr-off-ns = <24>; |
| gpmc,adv-on-ns = <0>; |
| gpmc,adv-rd-off-ns = <0>; |
| gpmc,adv-wr-off-ns = <0>; |
| gpmc,we-on-ns = <12>; |
| gpmc,we-off-ns = <18>; |
| gpmc,oe-on-ns = <12>; |
| gpmc,oe-off-ns = <48>; |
| gpmc,page-burst-access-ns = <0>; |
| gpmc,access-ns = <42>; |
| gpmc,rd-cycle-ns = <180>; |
| gpmc,wr-cycle-ns = <180>; |
| gpmc,bus-turnaround-ns = <0>; |
| gpmc,cycle2cycle-delay-ns = <0>; |
| gpmc,wait-monitoring-ns = <0>; |
| gpmc,clk-activation-ns = <0>; |
| gpmc,wr-access-ns = <0>; |
| gpmc,wr-data-mux-bus-ns = <12>; |
| }; |
| }; |
| |
| &mcspi1 { |
| /* |
| * For some reason, touchscreen is necessary for screen to work at |
| * all on real hw. It works well without it on emulator. |
| * |
| * Also... order in the device tree actually matters here. |
| */ |
| tsc2005@0 { |
| compatible = "ti,tsc2005"; |
| spi-max-frequency = <6000000>; |
| reg = <0>; |
| |
| vio-supply = <&vio>; |
| |
| reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */ |
| interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */ |
| |
| touchscreen-fuzz-x = <4>; |
| touchscreen-fuzz-y = <7>; |
| touchscreen-fuzz-pressure = <2>; |
| touchscreen-size-x = <4096>; |
| touchscreen-size-y = <4096>; |
| touchscreen-max-pressure = <2048>; |
| |
| ti,x-plate-ohms = <280>; |
| ti,esd-recovery-timeout-ms = <8000>; |
| }; |
| |
| lcd: acx565akm@2 { |
| compatible = "sony,acx565akm"; |
| spi-max-frequency = <6000000>; |
| reg = <2>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&acx565akm_pins>; |
| |
| label = "lcd"; |
| reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */ |
| |
| port { |
| lcd_in: endpoint { |
| remote-endpoint = <&sdi_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| &mcspi4 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&mcspi4_pins>; |
| |
| wl1251@0 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wl1251_pins>; |
| |
| vio-supply = <&vio>; |
| |
| compatible = "ti,wl1251"; |
| reg = <0>; |
| spi-max-frequency = <48000000>; |
| |
| spi-cpol; |
| spi-cpha; |
| |
| ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */ |
| |
| interrupt-parent = <&gpio2>; |
| interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */ |
| |
| clocks = <&vctcxo>; |
| }; |
| }; |
| |
| /* RNG not directly accessible on n900, see omap3-rom-rng instead */ |
| &rng_target { |
| status = "disabled"; |
| }; |
| |
| &usb_otg_hs { |
| interface-type = <0>; |
| usb-phy = <&usb2_phy>; |
| phys = <&usb2_phy>; |
| phy-names = "usb2-phy"; |
| mode = <2>; |
| power = <50>; |
| }; |
| |
| &uart1 { |
| status = "disabled"; |
| }; |
| |
| &uart2 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart2_pins>; |
| |
| bcm2048: bluetooth { |
| compatible = "brcm,bcm2048-nokia", "nokia,h4p-bluetooth"; |
| reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>; /* 91 */ |
| host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */ |
| bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */ |
| clocks = <&vctcxo>; |
| clock-names = "sysclk"; |
| }; |
| }; |
| |
| &uart3 { |
| interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&uart3_pins>; |
| }; |
| |
| &dss { |
| status = "ok"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&dss_sdi_pins>; |
| |
| vdds_sdi-supply = <&vaux1>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@1 { |
| reg = <1>; |
| |
| sdi_out: endpoint { |
| remote-endpoint = <&lcd_in>; |
| datapairs = <2>; |
| }; |
| }; |
| }; |
| }; |
| |
| &venc { |
| status = "ok"; |
| |
| vdda-supply = <&vdac>; |
| |
| port { |
| venc_out: endpoint { |
| remote-endpoint = <&tv_connector_in>; |
| ti,channels = <1>; |
| }; |
| }; |
| }; |
| |
| &mcbsp2 { |
| status = "ok"; |
| }; |
| |
| &ssi_port1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ssi_pins>; |
| |
| ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */ |
| |
| modem: hsi-client { |
| compatible = "nokia,n900-modem"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&modem_pins>; |
| |
| hsi-channel-ids = <0>, <1>, <2>, <3>; |
| hsi-channel-names = "mcsaab-control", |
| "speech-control", |
| "speech-data", |
| "mcsaab-data"; |
| hsi-speed-kbps = <55000>; |
| hsi-mode = "frame"; |
| hsi-flow = "synchronized"; |
| hsi-arb-mode = "round-robin"; |
| |
| interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */ |
| |
| gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */ |
| <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */ |
| <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */ |
| <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */ |
| <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */ |
| gpio-names = "cmt_apeslpx", |
| "cmt_rst_rq", |
| "cmt_en", |
| "cmt_rst", |
| "cmt_bsi"; |
| }; |
| }; |
| |
| &ssi_port2 { |
| status = "disabled"; |
| }; |
