| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Marvell 10G 88x3310 PHY driver |
| * |
| * Based upon the ID registers, this PHY appears to be a mixture of IPs |
| * from two different companies. |
| * |
| * There appears to be several different data paths through the PHY which |
| * are automatically managed by the PHY. The following has been determined |
| * via observation and experimentation for a setup using single-lane Serdes: |
| * |
| * SGMII PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for <= 1G) |
| * 10GBASE-KR PHYXS -- BASE-T PCS -- 10G PMA -- AN -- Copper (for 10G) |
| * 10GBASE-KR PHYXS -- BASE-R PCS -- Fiber |
| * |
| * With XAUI, observation shows: |
| * |
| * XAUI PHYXS -- <appropriate PCS as above> |
| * |
| * and no switching of the host interface mode occurs. |
| * |
| * If both the fiber and copper ports are connected, the first to gain |
| * link takes priority and the other port is completely locked out. |
| */ |
| #include <linux/ctype.h> |
| #include <linux/delay.h> |
| #include <linux/hwmon.h> |
| #include <linux/marvell_phy.h> |
| #include <linux/phy.h> |
| #include <linux/sfp.h> |
| |
| #define MV_PHY_ALASKA_NBT_QUIRK_MASK 0xfffffffe |
| #define MV_PHY_ALASKA_NBT_QUIRK_REV (MARVELL_PHY_ID_88X3310 | 0xa) |
| |
| enum { |
| MV_PMA_FW_VER0 = 0xc011, |
| MV_PMA_FW_VER1 = 0xc012, |
| MV_PMA_BOOT = 0xc050, |
| MV_PMA_BOOT_FATAL = BIT(0), |
| |
| MV_PCS_BASE_T = 0x0000, |
| MV_PCS_BASE_R = 0x1000, |
| MV_PCS_1000BASEX = 0x2000, |
| |
| MV_PCS_CSCR1 = 0x8000, |
| MV_PCS_CSCR1_ED_MASK = 0x0300, |
| MV_PCS_CSCR1_ED_OFF = 0x0000, |
| MV_PCS_CSCR1_ED_RX = 0x0200, |
| MV_PCS_CSCR1_ED_NLP = 0x0300, |
| MV_PCS_CSCR1_MDIX_MASK = 0x0060, |
| MV_PCS_CSCR1_MDIX_MDI = 0x0000, |
| MV_PCS_CSCR1_MDIX_MDIX = 0x0020, |
| MV_PCS_CSCR1_MDIX_AUTO = 0x0060, |
| |
| MV_PCS_CSSR1 = 0x8008, |
| MV_PCS_CSSR1_SPD1_MASK = 0xc000, |
| MV_PCS_CSSR1_SPD1_SPD2 = 0xc000, |
| MV_PCS_CSSR1_SPD1_1000 = 0x8000, |
| MV_PCS_CSSR1_SPD1_100 = 0x4000, |
| MV_PCS_CSSR1_SPD1_10 = 0x0000, |
| MV_PCS_CSSR1_DUPLEX_FULL= BIT(13), |
| MV_PCS_CSSR1_RESOLVED = BIT(11), |
| MV_PCS_CSSR1_MDIX = BIT(6), |
| MV_PCS_CSSR1_SPD2_MASK = 0x000c, |
| MV_PCS_CSSR1_SPD2_5000 = 0x0008, |
| MV_PCS_CSSR1_SPD2_2500 = 0x0004, |
| MV_PCS_CSSR1_SPD2_10000 = 0x0000, |
| |
| /* Temperature read register (88E2110 only) */ |
| MV_PCS_TEMP = 0x8042, |
| |
| /* These registers appear at 0x800X and 0xa00X - the 0xa00X control |
| * registers appear to set themselves to the 0x800X when AN is |
| * restarted, but status registers appear readable from either. |
| */ |
| MV_AN_CTRL1000 = 0x8000, /* 1000base-T control register */ |
| MV_AN_STAT1000 = 0x8001, /* 1000base-T status register */ |
| |
| /* Vendor2 MMD registers */ |
| MV_V2_PORT_CTRL = 0xf001, |
| MV_V2_PORT_CTRL_SWRST = BIT(15), |
| MV_V2_PORT_CTRL_PWRDOWN = BIT(11), |
| /* Temperature control/read registers (88X3310 only) */ |
| MV_V2_TEMP_CTRL = 0xf08a, |
| MV_V2_TEMP_CTRL_MASK = 0xc000, |
| MV_V2_TEMP_CTRL_SAMPLE = 0x0000, |
| MV_V2_TEMP_CTRL_DISABLE = 0xc000, |
| MV_V2_TEMP = 0xf08c, |
| MV_V2_TEMP_UNKNOWN = 0x9600, /* unknown function */ |
| }; |
| |
| struct mv3310_priv { |
| u32 firmware_ver; |
| |
| struct device *hwmon_dev; |
| char *hwmon_name; |
| }; |
| |
| #ifdef CONFIG_HWMON |
| static umode_t mv3310_hwmon_is_visible(const void *data, |
| enum hwmon_sensor_types type, |
| u32 attr, int channel) |
| { |
| if (type == hwmon_chip && attr == hwmon_chip_update_interval) |
| return 0444; |
| if (type == hwmon_temp && attr == hwmon_temp_input) |
| return 0444; |
| return 0; |
| } |
| |
| static int mv3310_hwmon_read_temp_reg(struct phy_device *phydev) |
| { |
| return phy_read_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP); |
| } |
| |
| static int mv2110_hwmon_read_temp_reg(struct phy_device *phydev) |
| { |
| return phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_TEMP); |
| } |
| |
| static int mv10g_hwmon_read_temp_reg(struct phy_device *phydev) |
| { |
| if (phydev->drv->phy_id == MARVELL_PHY_ID_88X3310) |
| return mv3310_hwmon_read_temp_reg(phydev); |
| else /* MARVELL_PHY_ID_88E2110 */ |
| return mv2110_hwmon_read_temp_reg(phydev); |
| } |
| |
| static int mv3310_hwmon_read(struct device *dev, enum hwmon_sensor_types type, |
| u32 attr, int channel, long *value) |
| { |
| struct phy_device *phydev = dev_get_drvdata(dev); |
| int temp; |
| |
| if (type == hwmon_chip && attr == hwmon_chip_update_interval) { |
| *value = MSEC_PER_SEC; |
| return 0; |
| } |
| |
| if (type == hwmon_temp && attr == hwmon_temp_input) { |
| temp = mv10g_hwmon_read_temp_reg(phydev); |
| if (temp < 0) |
| return temp; |
| |
| *value = ((temp & 0xff) - 75) * 1000; |
| |
| return 0; |
| } |
| |
| return -EOPNOTSUPP; |
| } |
| |
| static const struct hwmon_ops mv3310_hwmon_ops = { |
| .is_visible = mv3310_hwmon_is_visible, |
| .read = mv3310_hwmon_read, |
| }; |
| |
| static u32 mv3310_hwmon_chip_config[] = { |
| HWMON_C_REGISTER_TZ | HWMON_C_UPDATE_INTERVAL, |
| 0, |
| }; |
| |
| static const struct hwmon_channel_info mv3310_hwmon_chip = { |
| .type = hwmon_chip, |
| .config = mv3310_hwmon_chip_config, |
| }; |
| |
| static u32 mv3310_hwmon_temp_config[] = { |
| HWMON_T_INPUT, |
| 0, |
| }; |
| |
| static const struct hwmon_channel_info mv3310_hwmon_temp = { |
| .type = hwmon_temp, |
| .config = mv3310_hwmon_temp_config, |
| }; |
| |
| static const struct hwmon_channel_info *mv3310_hwmon_info[] = { |
| &mv3310_hwmon_chip, |
| &mv3310_hwmon_temp, |
| NULL, |
| }; |
| |
| static const struct hwmon_chip_info mv3310_hwmon_chip_info = { |
| .ops = &mv3310_hwmon_ops, |
| .info = mv3310_hwmon_info, |
| }; |
| |
| static int mv3310_hwmon_config(struct phy_device *phydev, bool enable) |
| { |
| u16 val; |
| int ret; |
| |
| if (phydev->drv->phy_id != MARVELL_PHY_ID_88X3310) |
| return 0; |
| |
| ret = phy_write_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP, |
| MV_V2_TEMP_UNKNOWN); |
| if (ret < 0) |
| return ret; |
| |
| val = enable ? MV_V2_TEMP_CTRL_SAMPLE : MV_V2_TEMP_CTRL_DISABLE; |
| |
| return phy_modify_mmd(phydev, MDIO_MMD_VEND2, MV_V2_TEMP_CTRL, |
| MV_V2_TEMP_CTRL_MASK, val); |
| } |
| |
| static void mv3310_hwmon_disable(void *data) |
| { |
| struct phy_device *phydev = data; |
| |
| mv3310_hwmon_config(phydev, false); |
| } |
| |
| static int mv3310_hwmon_probe(struct phy_device *phydev) |
| { |
| struct device *dev = &phydev->mdio.dev; |
| struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); |
| int i, j, ret; |
| |
| priv->hwmon_name = devm_kstrdup(dev, dev_name(dev), GFP_KERNEL); |
| if (!priv->hwmon_name) |
| return -ENODEV; |
| |
| for (i = j = 0; priv->hwmon_name[i]; i++) { |
| if (isalnum(priv->hwmon_name[i])) { |
| if (i != j) |
| priv->hwmon_name[j] = priv->hwmon_name[i]; |
| j++; |
| } |
| } |
| priv->hwmon_name[j] = '\0'; |
| |
| ret = mv3310_hwmon_config(phydev, true); |
| if (ret) |
| return ret; |
| |
| ret = devm_add_action_or_reset(dev, mv3310_hwmon_disable, phydev); |
| if (ret) |
| return ret; |
| |
| priv->hwmon_dev = devm_hwmon_device_register_with_info(dev, |
| priv->hwmon_name, phydev, |
| &mv3310_hwmon_chip_info, NULL); |
| |
| return PTR_ERR_OR_ZERO(priv->hwmon_dev); |
| } |
| #else |
| static inline int mv3310_hwmon_config(struct phy_device *phydev, bool enable) |
| { |
| return 0; |
| } |
| |
| static int mv3310_hwmon_probe(struct phy_device *phydev) |
| { |
| return 0; |
| } |
| #endif |
| |
| static int mv3310_power_down(struct phy_device *phydev) |
| { |
| return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, |
| MV_V2_PORT_CTRL_PWRDOWN); |
| } |
| |
| static int mv3310_power_up(struct phy_device *phydev) |
| { |
| struct mv3310_priv *priv = dev_get_drvdata(&phydev->mdio.dev); |
| int ret; |
| |
| ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, |
| MV_V2_PORT_CTRL_PWRDOWN); |
| |
| if (phydev->drv->phy_id != MARVELL_PHY_ID_88X3310 || |
| priv->firmware_ver < 0x00030000) |
| return ret; |
| |
| return phy_set_bits_mmd(phydev, MDIO_MMD_VEND2, MV_V2_PORT_CTRL, |
| MV_V2_PORT_CTRL_SWRST); |
| } |
| |
| static int mv3310_reset(struct phy_device *phydev, u32 unit) |
| { |
| int val, err; |
| |
| err = phy_modify_mmd(phydev, MDIO_MMD_PCS, unit + MDIO_CTRL1, |
| MDIO_CTRL1_RESET, MDIO_CTRL1_RESET); |
| if (err < 0) |
| return err; |
| |
| return phy_read_mmd_poll_timeout(phydev, MDIO_MMD_PCS, |
| unit + MDIO_CTRL1, val, |
| !(val & MDIO_CTRL1_RESET), |
| 5000, 100000, true); |
| } |
| |
| static int mv3310_get_edpd(struct phy_device *phydev, u16 *edpd) |
| { |
| int val; |
| |
| val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1); |
| if (val < 0) |
| return val; |
| |
| switch (val & MV_PCS_CSCR1_ED_MASK) { |
| case MV_PCS_CSCR1_ED_NLP: |
| *edpd = 1000; |
| break; |
| case MV_PCS_CSCR1_ED_RX: |
| *edpd = ETHTOOL_PHY_EDPD_NO_TX; |
| break; |
| default: |
| *edpd = ETHTOOL_PHY_EDPD_DISABLE; |
| break; |
| } |
| return 0; |
| } |
| |
| static int mv3310_set_edpd(struct phy_device *phydev, u16 edpd) |
| { |
| u16 val; |
| int err; |
| |
| switch (edpd) { |
| case 1000: |
| case ETHTOOL_PHY_EDPD_DFLT_TX_MSECS: |
| val = MV_PCS_CSCR1_ED_NLP; |
| break; |
| |
| case ETHTOOL_PHY_EDPD_NO_TX: |
| val = MV_PCS_CSCR1_ED_RX; |
| break; |
| |
| case ETHTOOL_PHY_EDPD_DISABLE: |
| val = MV_PCS_CSCR1_ED_OFF; |
| break; |
| |
| default: |
| return -EINVAL; |
| } |
| |
| err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1, |
| MV_PCS_CSCR1_ED_MASK, val); |
| if (err > 0) |
| err = mv3310_reset(phydev, MV_PCS_BASE_T); |
| |
| return err; |
| } |
| |
| static int mv3310_sfp_insert(void *upstream, const struct sfp_eeprom_id *id) |
| { |
| struct phy_device *phydev = upstream; |
| __ETHTOOL_DECLARE_LINK_MODE_MASK(support) = { 0, }; |
| phy_interface_t iface; |
| |
| sfp_parse_support(phydev->sfp_bus, id, support); |
| iface = sfp_select_interface(phydev->sfp_bus, support); |
| |
| if (iface != PHY_INTERFACE_MODE_10GBASER) { |
| dev_err(&phydev->mdio.dev, "incompatible SFP module inserted\n"); |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| static const struct sfp_upstream_ops mv3310_sfp_ops = { |
| .attach = phy_sfp_attach, |
| .detach = phy_sfp_detach, |
| .module_insert = mv3310_sfp_insert, |
| }; |
| |
| static int mv3310_probe(struct phy_device *phydev) |
| { |
| struct mv3310_priv *priv; |
| u32 mmd_mask = MDIO_DEVS_PMAPMD | MDIO_DEVS_AN; |
| int ret; |
| |
| if (!phydev->is_c45 || |
| (phydev->c45_ids.devices_in_package & mmd_mask) != mmd_mask) |
| return -ENODEV; |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_BOOT); |
| if (ret < 0) |
| return ret; |
| |
| if (ret & MV_PMA_BOOT_FATAL) { |
| dev_warn(&phydev->mdio.dev, |
| "PHY failed to boot firmware, status=%04x\n", ret); |
| return -ENODEV; |
| } |
| |
| priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| dev_set_drvdata(&phydev->mdio.dev, priv); |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_FW_VER0); |
| if (ret < 0) |
| return ret; |
| |
| priv->firmware_ver = ret << 16; |
| |
| ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, MV_PMA_FW_VER1); |
| if (ret < 0) |
| return ret; |
| |
| priv->firmware_ver |= ret; |
| |
| phydev_info(phydev, "Firmware version %u.%u.%u.%u\n", |
| priv->firmware_ver >> 24, (priv->firmware_ver >> 16) & 255, |
| (priv->firmware_ver >> 8) & 255, priv->firmware_ver & 255); |
| |
| /* Powering down the port when not in use saves about 600mW */ |
| ret = mv3310_power_down(phydev); |
| if (ret) |
| return ret; |
| |
| ret = mv3310_hwmon_probe(phydev); |
| if (ret) |
| return ret; |
| |
| return phy_sfp_probe(phydev, &mv3310_sfp_ops); |
| } |
| |
| static int mv3310_suspend(struct phy_device *phydev) |
| { |
| return mv3310_power_down(phydev); |
| } |
| |
| static int mv3310_resume(struct phy_device *phydev) |
| { |
| int ret; |
| |
| ret = mv3310_power_up(phydev); |
| if (ret) |
| return ret; |
| |
| return mv3310_hwmon_config(phydev, true); |
| } |
| |
| /* Some PHYs in the Alaska family such as the 88X3310 and the 88E2010 |
| * don't set bit 14 in PMA Extended Abilities (1.11), although they do |
| * support 2.5GBASET and 5GBASET. For these models, we can still read their |
| * 2.5G/5G extended abilities register (1.21). We detect these models based on |
| * the PMA device identifier, with a mask matching models known to have this |
| * issue |
| */ |
| static bool mv3310_has_pma_ngbaset_quirk(struct phy_device *phydev) |
| { |
| if (!(phydev->c45_ids.devices_in_package & MDIO_DEVS_PMAPMD)) |
| return false; |
| |
| /* Only some revisions of the 88X3310 family PMA seem to be impacted */ |
| return (phydev->c45_ids.device_ids[MDIO_MMD_PMAPMD] & |
| MV_PHY_ALASKA_NBT_QUIRK_MASK) == MV_PHY_ALASKA_NBT_QUIRK_REV; |
| } |
| |
| static int mv3310_config_init(struct phy_device *phydev) |
| { |
| int err; |
| |
| /* Check that the PHY interface type is compatible */ |
| if (phydev->interface != PHY_INTERFACE_MODE_SGMII && |
| phydev->interface != PHY_INTERFACE_MODE_2500BASEX && |
| phydev->interface != PHY_INTERFACE_MODE_XAUI && |
| phydev->interface != PHY_INTERFACE_MODE_RXAUI && |
| phydev->interface != PHY_INTERFACE_MODE_10GBASER) |
| return -ENODEV; |
| |
| phydev->mdix_ctrl = ETH_TP_MDI_AUTO; |
| |
| /* Power up so reset works */ |
| err = mv3310_power_up(phydev); |
| if (err) |
| return err; |
| |
| /* Enable EDPD mode - saving 600mW */ |
| return mv3310_set_edpd(phydev, ETHTOOL_PHY_EDPD_DFLT_TX_MSECS); |
| } |
| |
| static int mv3310_get_features(struct phy_device *phydev) |
| { |
| int ret, val; |
| |
| ret = genphy_c45_pma_read_abilities(phydev); |
| if (ret) |
| return ret; |
| |
| if (mv3310_has_pma_ngbaset_quirk(phydev)) { |
| val = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, |
| MDIO_PMA_NG_EXTABLE); |
| if (val < 0) |
| return val; |
| |
| linkmode_mod_bit(ETHTOOL_LINK_MODE_2500baseT_Full_BIT, |
| phydev->supported, |
| val & MDIO_PMA_NG_EXTABLE_2_5GBT); |
| |
| linkmode_mod_bit(ETHTOOL_LINK_MODE_5000baseT_Full_BIT, |
| phydev->supported, |
| val & MDIO_PMA_NG_EXTABLE_5GBT); |
| } |
| |
| return 0; |
| } |
| |
| static int mv3310_config_mdix(struct phy_device *phydev) |
| { |
| u16 val; |
| int err; |
| |
| switch (phydev->mdix_ctrl) { |
| case ETH_TP_MDI_AUTO: |
| val = MV_PCS_CSCR1_MDIX_AUTO; |
| break; |
| case ETH_TP_MDI_X: |
| val = MV_PCS_CSCR1_MDIX_MDIX; |
| break; |
| case ETH_TP_MDI: |
| val = MV_PCS_CSCR1_MDIX_MDI; |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| err = phy_modify_mmd_changed(phydev, MDIO_MMD_PCS, MV_PCS_CSCR1, |
| MV_PCS_CSCR1_MDIX_MASK, val); |
| if (err > 0) |
| err = mv3310_reset(phydev, MV_PCS_BASE_T); |
| |
| return err; |
| } |
| |
| static int mv3310_config_aneg(struct phy_device *phydev) |
| { |
| bool changed = false; |
| u16 reg; |
| int ret; |
| |
| ret = mv3310_config_mdix(phydev); |
| if (ret < 0) |
| return ret; |
| |
| if (phydev->autoneg == AUTONEG_DISABLE) |
| return genphy_c45_pma_setup_forced(phydev); |
| |
| ret = genphy_c45_an_config_aneg(phydev); |
| if (ret < 0) |
| return ret; |
| if (ret > 0) |
| changed = true; |
| |
| /* Clause 45 has no standardized support for 1000BaseT, therefore |
| * use vendor registers for this mode. |
| */ |
| reg = linkmode_adv_to_mii_ctrl1000_t(phydev->advertising); |
| ret = phy_modify_mmd_changed(phydev, MDIO_MMD_AN, MV_AN_CTRL1000, |
| ADVERTISE_1000FULL | ADVERTISE_1000HALF, reg); |
| if (ret < 0) |
| return ret; |
| if (ret > 0) |
| changed = true; |
| |
| return genphy_c45_check_and_restart_aneg(phydev, changed); |
| } |
| |
| static int mv3310_aneg_done(struct phy_device *phydev) |
| { |
| int val; |
| |
| val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1); |
| if (val < 0) |
| return val; |
| |
| if (val & MDIO_STAT1_LSTATUS) |
| return 1; |
| |
| return genphy_c45_aneg_done(phydev); |
| } |
| |
| static void mv3310_update_interface(struct phy_device *phydev) |
| { |
| if ((phydev->interface == PHY_INTERFACE_MODE_SGMII || |
| phydev->interface == PHY_INTERFACE_MODE_2500BASEX || |
| phydev->interface == PHY_INTERFACE_MODE_10GBASER) && |
| phydev->link) { |
| /* The PHY automatically switches its serdes interface (and |
| * active PHYXS instance) between Cisco SGMII, 10GBase-R and |
| * 2500BaseX modes according to the speed. Florian suggests |
| * setting phydev->interface to communicate this to the MAC. |
| * Only do this if we are already in one of the above modes. |
| */ |
| switch (phydev->speed) { |
| case SPEED_10000: |
| phydev->interface = PHY_INTERFACE_MODE_10GBASER; |
| break; |
| case SPEED_2500: |
| phydev->interface = PHY_INTERFACE_MODE_2500BASEX; |
| break; |
| case SPEED_1000: |
| case SPEED_100: |
| case SPEED_10: |
| phydev->interface = PHY_INTERFACE_MODE_SGMII; |
| break; |
| default: |
| break; |
| } |
| } |
| } |
| |
| /* 10GBASE-ER,LR,LRM,SR do not support autonegotiation. */ |
| static int mv3310_read_status_10gbaser(struct phy_device *phydev) |
| { |
| phydev->link = 1; |
| phydev->speed = SPEED_10000; |
| phydev->duplex = DUPLEX_FULL; |
| |
| return 0; |
| } |
| |
| static int mv3310_read_status_copper(struct phy_device *phydev) |
| { |
| int cssr1, speed, val; |
| |
| val = genphy_c45_read_link(phydev); |
| if (val < 0) |
| return val; |
| |
| val = phy_read_mmd(phydev, MDIO_MMD_AN, MDIO_STAT1); |
| if (val < 0) |
| return val; |
| |
| cssr1 = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_CSSR1); |
| if (cssr1 < 0) |
| return val; |
| |
| /* If the link settings are not resolved, mark the link down */ |
| if (!(cssr1 & MV_PCS_CSSR1_RESOLVED)) { |
| phydev->link = 0; |
| return 0; |
| } |
| |
| /* Read the copper link settings */ |
| speed = cssr1 & MV_PCS_CSSR1_SPD1_MASK; |
| if (speed == MV_PCS_CSSR1_SPD1_SPD2) |
| speed |= cssr1 & MV_PCS_CSSR1_SPD2_MASK; |
| |
| switch (speed) { |
| case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_10000: |
| phydev->speed = SPEED_10000; |
| break; |
| |
| case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_5000: |
| phydev->speed = SPEED_5000; |
| break; |
| |
| case MV_PCS_CSSR1_SPD1_SPD2 | MV_PCS_CSSR1_SPD2_2500: |
| phydev->speed = SPEED_2500; |
| break; |
| |
| case MV_PCS_CSSR1_SPD1_1000: |
| phydev->speed = SPEED_1000; |
| break; |
| |
| case MV_PCS_CSSR1_SPD1_100: |
| phydev->speed = SPEED_100; |
| break; |
| |
| case MV_PCS_CSSR1_SPD1_10: |
| phydev->speed = SPEED_10; |
| break; |
| } |
| |
| phydev->duplex = cssr1 & MV_PCS_CSSR1_DUPLEX_FULL ? |
| DUPLEX_FULL : DUPLEX_HALF; |
| phydev->mdix = cssr1 & MV_PCS_CSSR1_MDIX ? |
| ETH_TP_MDI_X : ETH_TP_MDI; |
| |
| if (val & MDIO_AN_STAT1_COMPLETE) { |
| val = genphy_c45_read_lpa(phydev); |
| if (val < 0) |
| return val; |
| |
| /* Read the link partner's 1G advertisement */ |
| val = phy_read_mmd(phydev, MDIO_MMD_AN, MV_AN_STAT1000); |
| if (val < 0) |
| return val; |
| |
| mii_stat1000_mod_linkmode_lpa_t(phydev->lp_advertising, val); |
| |
| /* Update the pause status */ |
| phy_resolve_aneg_pause(phydev); |
| } |
| |
| return 0; |
| } |
| |
| static int mv3310_read_status(struct phy_device *phydev) |
| { |
| int err, val; |
| |
| phydev->speed = SPEED_UNKNOWN; |
| phydev->duplex = DUPLEX_UNKNOWN; |
| linkmode_zero(phydev->lp_advertising); |
| phydev->link = 0; |
| phydev->pause = 0; |
| phydev->asym_pause = 0; |
| phydev->mdix = ETH_TP_MDI_INVALID; |
| |
| val = phy_read_mmd(phydev, MDIO_MMD_PCS, MV_PCS_BASE_R + MDIO_STAT1); |
| if (val < 0) |
| return val; |
| |
| if (val & MDIO_STAT1_LSTATUS) |
| err = mv3310_read_status_10gbaser(phydev); |
| else |
| err = mv3310_read_status_copper(phydev); |
| if (err < 0) |
| return err; |
| |
| if (phydev->link) |
| mv3310_update_interface(phydev); |
| |
| return 0; |
| } |
| |
| static int mv3310_get_tunable(struct phy_device *phydev, |
| struct ethtool_tunable *tuna, void *data) |
| { |
| switch (tuna->id) { |
| case ETHTOOL_PHY_EDPD: |
| return mv3310_get_edpd(phydev, data); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int mv3310_set_tunable(struct phy_device *phydev, |
| struct ethtool_tunable *tuna, const void *data) |
| { |
| switch (tuna->id) { |
| case ETHTOOL_PHY_EDPD: |
| return mv3310_set_edpd(phydev, *(u16 *)data); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static struct phy_driver mv3310_drivers[] = { |
| { |
| .phy_id = MARVELL_PHY_ID_88X3310, |
| .phy_id_mask = MARVELL_PHY_ID_MASK, |
| .name = "mv88x3310", |
| .get_features = mv3310_get_features, |
| .config_init = mv3310_config_init, |
| .probe = mv3310_probe, |
| .suspend = mv3310_suspend, |
| .resume = mv3310_resume, |
| .config_aneg = mv3310_config_aneg, |
| .aneg_done = mv3310_aneg_done, |
| .read_status = mv3310_read_status, |
| .get_tunable = mv3310_get_tunable, |
| .set_tunable = mv3310_set_tunable, |
| }, |
| { |
| .phy_id = MARVELL_PHY_ID_88E2110, |
| .phy_id_mask = MARVELL_PHY_ID_MASK, |
| .name = "mv88x2110", |
| .probe = mv3310_probe, |
| .suspend = mv3310_suspend, |
| .resume = mv3310_resume, |
| .config_init = mv3310_config_init, |
| .config_aneg = mv3310_config_aneg, |
| .aneg_done = mv3310_aneg_done, |
| .read_status = mv3310_read_status, |
| .get_tunable = mv3310_get_tunable, |
| .set_tunable = mv3310_set_tunable, |
| }, |
| }; |
| |
| module_phy_driver(mv3310_drivers); |
| |
| static struct mdio_device_id __maybe_unused mv3310_tbl[] = { |
| { MARVELL_PHY_ID_88X3310, MARVELL_PHY_ID_MASK }, |
| { MARVELL_PHY_ID_88E2110, MARVELL_PHY_ID_MASK }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(mdio, mv3310_tbl); |
| MODULE_DESCRIPTION("Marvell Alaska X 10Gigabit Ethernet PHY driver (MV88X3310)"); |
| MODULE_LICENSE("GPL"); |