| /* |
| * Device Tree Source for am3517 SoC |
| * |
| * Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/ |
| * |
| * This file is licensed under the terms of the GNU General Public License |
| * version 2. This program is licensed "as is" without any warranty of any |
| * kind, whether express or implied. |
| */ |
| |
| #include "omap3.dtsi" |
| |
| /* AM3517 doesn't appear to have the crypto engines defined in omap3.dtsi */ |
| /delete-node/ &aes1_target; |
| /delete-node/ &aes2_target; |
| |
| / { |
| aliases { |
| serial3 = &uart4; |
| can = &hecc; |
| }; |
| |
| cpus { |
| cpu: cpu@0 { |
| /* Based on OMAP3630 variants OPP50 and OPP100 */ |
| operating-points-v2 = <&cpu0_opp_table>; |
| |
| clock-latency = <300000>; /* From legacy driver */ |
| }; |
| }; |
| |
| cpu0_opp_table: opp-table { |
| compatible = "operating-points-v2-ti-cpu"; |
| syscon = <&scm_conf>; |
| /* |
| * AM3517 TRM only lists 600MHz @ 1.2V, but omap36xx |
| * appear to operate at 300MHz as well. Since AM3517 only |
| * lists one operating voltage, it will remain fixed at 1.2V |
| */ |
| opp50-300000000 { |
| opp-hz = /bits/ 64 <300000000>; |
| opp-microvolt = <1200000>; |
| opp-supported-hw = <0xffffffff 0xffffffff>; |
| opp-suspend; |
| }; |
| |
| opp100-600000000 { |
| opp-hz = /bits/ 64 <600000000>; |
| opp-microvolt = <1200000>; |
| opp-supported-hw = <0xffffffff 0xffffffff>; |
| }; |
| }; |
| |
| ocp@68000000 { |
| am35x_otg_hs: am35x_otg_hs@5c040000 { |
| compatible = "ti,omap3-musb"; |
| ti,hwmods = "am35x_otg_hs"; |
| status = "disabled"; |
| reg = <0x5c040000 0x1000>; |
| interrupts = <71>; |
| interrupt-names = "mc"; |
| }; |
| |
| davinci_emac: ethernet@5c000000 { |
| compatible = "ti,am3517-emac"; |
| ti,hwmods = "davinci_emac"; |
| status = "disabled"; |
| reg = <0x5c000000 0x30000>; |
| interrupts = <67 68 69 70>; |
| syscon = <&scm_conf>; |
| ti,davinci-ctrl-reg-offset = <0x10000>; |
| ti,davinci-ctrl-mod-reg-offset = <0>; |
| ti,davinci-ctrl-ram-offset = <0x20000>; |
| ti,davinci-ctrl-ram-size = <0x2000>; |
| ti,davinci-rmii-en = /bits/ 8 <1>; |
| local-mac-address = [ 00 00 00 00 00 00 ]; |
| clocks = <&emac_ick>; |
| clock-names = "ick"; |
| }; |
| |
| davinci_mdio: mdio@5c030000 { |
| compatible = "ti,davinci_mdio"; |
| ti,hwmods = "davinci_mdio"; |
| status = "disabled"; |
| reg = <0x5c030000 0x1000>; |
| bus_freq = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| clocks = <&emac_fck>; |
| clock-names = "fck"; |
| }; |
| |
| uart4: serial@4809e000 { |
| compatible = "ti,omap3-uart"; |
| ti,hwmods = "uart4"; |
| status = "disabled"; |
| reg = <0x4809e000 0x400>; |
| interrupts = <84>; |
| dmas = <&sdma 55 &sdma 54>; |
| dma-names = "tx", "rx"; |
| clock-frequency = <48000000>; |
| }; |
| |
| omap3_pmx_core2: pinmux@480025d8 { |
| compatible = "ti,omap3-padconf", "pinctrl-single"; |
| reg = <0x480025d8 0x24>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #pinctrl-cells = <1>; |
| #interrupt-cells = <1>; |
| interrupt-controller; |
| pinctrl-single,register-width = <16>; |
| pinctrl-single,function-mask = <0xff1f>; |
| }; |
| |
| hecc: can@5c050000 { |
| compatible = "ti,am3517-hecc"; |
| status = "disabled"; |
| reg = <0x5c050000 0x80>, |
| <0x5c053000 0x180>, |
| <0x5c052000 0x200>; |
| reg-names = "hecc", "hecc-ram", "mbx"; |
| interrupts = <24>; |
| clocks = <&hecc_ck>; |
| }; |
| |
| /* |
| * On am3517 the OCP registers do not seem to be accessible |
| * similar to the omap34xx. Maybe SGX is permanently set to |
| * "OCP bypass mode", or maybe there is OCP_SYSCONFIG that is |
| * write-only at 0x50000e10. We detect SGX based on the SGX |
| * revision register instead of the unreadable OCP revision |
| * register. |
| */ |
| sgx_module: target-module@50000000 { |
| compatible = "ti,sysc-omap2", "ti,sysc"; |
| reg = <0x50000014 0x4>; |
| reg-names = "rev"; |
| clocks = <&sgx_fck>, <&sgx_ick>; |
| clock-names = "fck", "ick"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges = <0 0x50000000 0x4000>; |
| |
| /* |
| * Closed source PowerVR driver, no child device |
| * binding or driver in mainline |
| */ |
| }; |
| }; |
| }; |
| |
| /* Not currently working, probably needs at least different clocks */ |
| &rng_target { |
| status = "disabled"; |
| /delete-property/ clocks; |
| }; |
| |
| /* Table Table 5-79 of the TRM shows 480ab000 is reserved */ |
| &usb_otg_hs { |
| status = "disabled"; |
| }; |
| |
| &iva { |
| status = "disabled"; |
| }; |
| |
| &mailbox { |
| status = "disabled"; |
| }; |
| |
| &mmu_isp { |
| status = "disabled"; |
| }; |
| |
| #include "am35xx-clocks.dtsi" |
| #include "omap36xx-am35xx-omap3430es2plus-clocks.dtsi" |
| |
| /* Preferred always-on timer for clocksource */ |
| &timer1_target { |
| ti,no-reset-on-init; |
| ti,no-idle; |
| timer@0 { |
| assigned-clocks = <&gpt1_fck>; |
| assigned-clock-parents = <&sys_ck>; |
| }; |
| }; |
| |
| /* Preferred timer for clockevent */ |
| &timer2_target { |
| ti,no-reset-on-init; |
| ti,no-idle; |
| timer@0 { |
| assigned-clocks = <&gpt2_fck>; |
| assigned-clock-parents = <&sys_ck>; |
| }; |
| }; |