| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Elida kd35t133 5.5" MIPI-DSI panel driver |
| * Copyright (C) 2020 Theobroma Systems Design und Consulting GmbH |
| * |
| * based on |
| * |
| * Rockteck jh057n00900 5.5" MIPI-DSI panel driver |
| * Copyright (C) Purism SPC 2019 |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/gpio/consumer.h> |
| #include <linux/media-bus-format.h> |
| #include <linux/module.h> |
| #include <linux/of.h> |
| #include <linux/regulator/consumer.h> |
| |
| #include <video/display_timing.h> |
| #include <video/mipi_display.h> |
| |
| #include <drm/drm_mipi_dsi.h> |
| #include <drm/drm_modes.h> |
| #include <drm/drm_panel.h> |
| |
| /* Manufacturer specific Commands send via DSI */ |
| #define KD35T133_CMD_INTERFACEMODECTRL 0xb0 |
| #define KD35T133_CMD_FRAMERATECTRL 0xb1 |
| #define KD35T133_CMD_DISPLAYINVERSIONCTRL 0xb4 |
| #define KD35T133_CMD_DISPLAYFUNCTIONCTRL 0xb6 |
| #define KD35T133_CMD_POWERCONTROL1 0xc0 |
| #define KD35T133_CMD_POWERCONTROL2 0xc1 |
| #define KD35T133_CMD_VCOMCONTROL 0xc5 |
| #define KD35T133_CMD_POSITIVEGAMMA 0xe0 |
| #define KD35T133_CMD_NEGATIVEGAMMA 0xe1 |
| #define KD35T133_CMD_SETIMAGEFUNCTION 0xe9 |
| #define KD35T133_CMD_ADJUSTCONTROL3 0xf7 |
| |
| struct kd35t133 { |
| struct device *dev; |
| struct drm_panel panel; |
| struct gpio_desc *reset_gpio; |
| struct regulator *vdd; |
| struct regulator *iovcc; |
| bool prepared; |
| }; |
| |
| static inline struct kd35t133 *panel_to_kd35t133(struct drm_panel *panel) |
| { |
| return container_of(panel, struct kd35t133, panel); |
| } |
| |
| #define dsi_dcs_write_seq(dsi, cmd, seq...) do { \ |
| static const u8 b[] = { cmd, seq }; \ |
| int ret; \ |
| ret = mipi_dsi_dcs_write_buffer(dsi, b, ARRAY_SIZE(b)); \ |
| if (ret < 0) \ |
| return ret; \ |
| } while (0) |
| |
| static int kd35t133_init_sequence(struct kd35t133 *ctx) |
| { |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| struct device *dev = ctx->dev; |
| |
| /* |
| * Init sequence was supplied by the panel vendor with minimal |
| * documentation. |
| */ |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_POSITIVEGAMMA, |
| 0x00, 0x13, 0x18, 0x04, 0x0f, 0x06, 0x3a, 0x56, |
| 0x4d, 0x03, 0x0a, 0x06, 0x30, 0x3e, 0x0f); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_NEGATIVEGAMMA, |
| 0x00, 0x13, 0x18, 0x01, 0x11, 0x06, 0x38, 0x34, |
| 0x4d, 0x06, 0x0d, 0x0b, 0x31, 0x37, 0x0f); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_POWERCONTROL1, 0x18, 0x17); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_POWERCONTROL2, 0x41); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_VCOMCONTROL, 0x00, 0x1a, 0x80); |
| dsi_dcs_write_seq(dsi, MIPI_DCS_SET_ADDRESS_MODE, 0x48); |
| dsi_dcs_write_seq(dsi, MIPI_DCS_SET_PIXEL_FORMAT, 0x55); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_INTERFACEMODECTRL, 0x00); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_FRAMERATECTRL, 0xa0); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_DISPLAYINVERSIONCTRL, 0x02); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_DISPLAYFUNCTIONCTRL, |
| 0x20, 0x02); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_SETIMAGEFUNCTION, 0x00); |
| dsi_dcs_write_seq(dsi, KD35T133_CMD_ADJUSTCONTROL3, |
| 0xa9, 0x51, 0x2c, 0x82); |
| mipi_dsi_dcs_write(dsi, MIPI_DCS_ENTER_INVERT_MODE, NULL, 0); |
| |
| dev_dbg(dev, "Panel init sequence done\n"); |
| return 0; |
| } |
| |
| static int kd35t133_unprepare(struct drm_panel *panel) |
| { |
| struct kd35t133 *ctx = panel_to_kd35t133(panel); |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| if (!ctx->prepared) |
| return 0; |
| |
| ret = mipi_dsi_dcs_set_display_off(dsi); |
| if (ret < 0) |
| dev_err(ctx->dev, "failed to set display off: %d\n", ret); |
| |
| ret = mipi_dsi_dcs_enter_sleep_mode(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "failed to enter sleep mode: %d\n", ret); |
| return ret; |
| } |
| |
| regulator_disable(ctx->iovcc); |
| regulator_disable(ctx->vdd); |
| |
| ctx->prepared = false; |
| |
| return 0; |
| } |
| |
| static int kd35t133_prepare(struct drm_panel *panel) |
| { |
| struct kd35t133 *ctx = panel_to_kd35t133(panel); |
| struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev); |
| int ret; |
| |
| if (ctx->prepared) |
| return 0; |
| |
| dev_dbg(ctx->dev, "Resetting the panel\n"); |
| ret = regulator_enable(ctx->vdd); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to enable vdd supply: %d\n", ret); |
| return ret; |
| } |
| |
| ret = regulator_enable(ctx->iovcc); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to enable iovcc supply: %d\n", ret); |
| goto disable_vdd; |
| } |
| |
| msleep(20); |
| |
| gpiod_set_value_cansleep(ctx->reset_gpio, 1); |
| usleep_range(10, 20); |
| gpiod_set_value_cansleep(ctx->reset_gpio, 0); |
| |
| msleep(20); |
| |
| ret = mipi_dsi_dcs_exit_sleep_mode(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to exit sleep mode: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| msleep(250); |
| |
| ret = kd35t133_init_sequence(ctx); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Panel init sequence failed: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| ret = mipi_dsi_dcs_set_display_on(dsi); |
| if (ret < 0) { |
| dev_err(ctx->dev, "Failed to set display on: %d\n", ret); |
| goto disable_iovcc; |
| } |
| |
| msleep(50); |
| |
| ctx->prepared = true; |
| |
| return 0; |
| |
| disable_iovcc: |
| regulator_disable(ctx->iovcc); |
| disable_vdd: |
| regulator_disable(ctx->vdd); |
| return ret; |
| } |
| |
| static const struct drm_display_mode default_mode = { |
| .hdisplay = 320, |
| .hsync_start = 320 + 130, |
| .hsync_end = 320 + 130 + 4, |
| .htotal = 320 + 130 + 4 + 130, |
| .vdisplay = 480, |
| .vsync_start = 480 + 2, |
| .vsync_end = 480 + 2 + 1, |
| .vtotal = 480 + 2 + 1 + 2, |
| .clock = 17000, |
| .width_mm = 42, |
| .height_mm = 82, |
| }; |
| |
| static int kd35t133_get_modes(struct drm_panel *panel, |
| struct drm_connector *connector) |
| { |
| struct kd35t133 *ctx = panel_to_kd35t133(panel); |
| struct drm_display_mode *mode; |
| |
| mode = drm_mode_duplicate(connector->dev, &default_mode); |
| if (!mode) { |
| dev_err(ctx->dev, "Failed to add mode %ux%u@%u\n", |
| default_mode.hdisplay, default_mode.vdisplay, |
| drm_mode_vrefresh(&default_mode)); |
| return -ENOMEM; |
| } |
| |
| drm_mode_set_name(mode); |
| |
| mode->type = DRM_MODE_TYPE_DRIVER | DRM_MODE_TYPE_PREFERRED; |
| connector->display_info.width_mm = mode->width_mm; |
| connector->display_info.height_mm = mode->height_mm; |
| drm_mode_probed_add(connector, mode); |
| |
| return 1; |
| } |
| |
| static const struct drm_panel_funcs kd35t133_funcs = { |
| .unprepare = kd35t133_unprepare, |
| .prepare = kd35t133_prepare, |
| .get_modes = kd35t133_get_modes, |
| }; |
| |
| static int kd35t133_probe(struct mipi_dsi_device *dsi) |
| { |
| struct device *dev = &dsi->dev; |
| struct kd35t133 *ctx; |
| int ret; |
| |
| ctx = devm_kzalloc(dev, sizeof(*ctx), GFP_KERNEL); |
| if (!ctx) |
| return -ENOMEM; |
| |
| ctx->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW); |
| if (IS_ERR(ctx->reset_gpio)) { |
| dev_err(dev, "cannot get reset gpio\n"); |
| return PTR_ERR(ctx->reset_gpio); |
| } |
| |
| ctx->vdd = devm_regulator_get(dev, "vdd"); |
| if (IS_ERR(ctx->vdd)) { |
| ret = PTR_ERR(ctx->vdd); |
| if (ret != -EPROBE_DEFER) |
| dev_err(dev, "Failed to request vdd regulator: %d\n", ret); |
| return ret; |
| } |
| |
| ctx->iovcc = devm_regulator_get(dev, "iovcc"); |
| if (IS_ERR(ctx->iovcc)) { |
| ret = PTR_ERR(ctx->iovcc); |
| if (ret != -EPROBE_DEFER) |
| dev_err(dev, "Failed to request iovcc regulator: %d\n", ret); |
| return ret; |
| } |
| |
| mipi_dsi_set_drvdata(dsi, ctx); |
| |
| ctx->dev = dev; |
| |
| dsi->lanes = 1; |
| dsi->format = MIPI_DSI_FMT_RGB888; |
| dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | |
| MIPI_DSI_MODE_LPM | MIPI_DSI_MODE_EOT_PACKET; |
| |
| drm_panel_init(&ctx->panel, &dsi->dev, &kd35t133_funcs, |
| DRM_MODE_CONNECTOR_DSI); |
| |
| ret = drm_panel_of_backlight(&ctx->panel); |
| if (ret) |
| return ret; |
| |
| drm_panel_add(&ctx->panel); |
| |
| ret = mipi_dsi_attach(dsi); |
| if (ret < 0) { |
| dev_err(dev, "mipi_dsi_attach failed: %d\n", ret); |
| drm_panel_remove(&ctx->panel); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void kd35t133_shutdown(struct mipi_dsi_device *dsi) |
| { |
| struct kd35t133 *ctx = mipi_dsi_get_drvdata(dsi); |
| int ret; |
| |
| ret = drm_panel_unprepare(&ctx->panel); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to unprepare panel: %d\n", ret); |
| |
| ret = drm_panel_disable(&ctx->panel); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to disable panel: %d\n", ret); |
| } |
| |
| static int kd35t133_remove(struct mipi_dsi_device *dsi) |
| { |
| struct kd35t133 *ctx = mipi_dsi_get_drvdata(dsi); |
| int ret; |
| |
| kd35t133_shutdown(dsi); |
| |
| ret = mipi_dsi_detach(dsi); |
| if (ret < 0) |
| dev_err(&dsi->dev, "Failed to detach from DSI host: %d\n", ret); |
| |
| drm_panel_remove(&ctx->panel); |
| |
| return 0; |
| } |
| |
| static const struct of_device_id kd35t133_of_match[] = { |
| { .compatible = "elida,kd35t133" }, |
| { /* sentinel */ } |
| }; |
| MODULE_DEVICE_TABLE(of, kd35t133_of_match); |
| |
| static struct mipi_dsi_driver kd35t133_driver = { |
| .driver = { |
| .name = "panel-elida-kd35t133", |
| .of_match_table = kd35t133_of_match, |
| }, |
| .probe = kd35t133_probe, |
| .remove = kd35t133_remove, |
| .shutdown = kd35t133_shutdown, |
| }; |
| module_mipi_dsi_driver(kd35t133_driver); |
| |
| MODULE_AUTHOR("Heiko Stuebner <heiko.stuebner@theobroma-systems.com>"); |
| MODULE_DESCRIPTION("DRM driver for Elida kd35t133 MIPI DSI panel"); |
| MODULE_LICENSE("GPL v2"); |