| // SPDX-License-Identifier: BSD-3-Clause |
| /* |
| * Copyright (c) 2021, AngeloGioacchino Del Regno |
| * <angelogioacchino.delregno@somainline.org> |
| */ |
| |
| /dts-v1/; |
| |
| #include "msm8998-mtp.dtsi" |
| |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/leds/common.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "F(x)tec Pro1 (QX1000)"; |
| compatible = "fxtec,pro1", "qcom,msm8998"; |
| chassis-type = "handset"; |
| qcom,board-id = <0x02000b 0x10>; |
| |
| /* |
| * Until we hook up type-c detection, we |
| * have to stick with this. But it works. |
| */ |
| extcon_usb: extcon-usb { |
| compatible = "linux,extcon-usb-gpio"; |
| id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>; |
| }; |
| |
| gpio-hall-sensors { |
| compatible = "gpio-keys"; |
| input-name = "hall-sensors"; |
| label = "Hall sensors"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&hall_sensor1_default>; |
| |
| hall-sensor1 { |
| label = "Keyboard Hall Sensor"; |
| gpios = <&tlmm 124 GPIO_ACTIVE_HIGH>; |
| debounce-interval = <15>; |
| gpio-key,wakeup; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_KEYPAD_SLIDE>; |
| }; |
| }; |
| |
| gpio-kb-extra-keys { |
| compatible = "gpio-keys"; |
| input-name = "extra-kb-keys"; |
| label = "Keyboard extra keys"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_kb_pins_extra>; |
| |
| home { |
| label = "Home"; |
| gpios = <&tlmm 21 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOMEPAGE>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| super-l { |
| label = "Super Left"; |
| gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_FN>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| super-r { |
| label = "Super Right"; |
| gpios = <&tlmm 33 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_FN>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| shift { |
| label = "Shift"; |
| gpios = <&tlmm 114 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_RIGHTSHIFT>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| ctrl { |
| label = "Ctrl"; |
| gpios = <&tlmm 128 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_LEFTCTRL>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| alt { |
| label = "Alt"; |
| gpios = <&tlmm 129 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_LEFTALT>; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| input-name = "side-buttons"; |
| label = "Side buttons"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&vol_up_pin_a>, <&cam_focus_pin_a>, |
| <&cam_snapshot_pin_a>; |
| vol-up { |
| label = "Volume Up"; |
| gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_VOLUMEUP>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| }; |
| |
| camera-snapshot { |
| label = "Camera Snapshot"; |
| gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA>; |
| debounce-interval = <15>; |
| }; |
| |
| camera-focus { |
| label = "Camera Focus"; |
| gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_KEY>; |
| linux,code = <KEY_CAMERA_FOCUS>; |
| debounce-interval = <15>; |
| }; |
| }; |
| |
| keyboard-leds { |
| compatible = "gpio-leds"; |
| |
| backlight { |
| color = <LED_COLOR_ID_WHITE>; |
| default-state = "off"; |
| function = LED_FUNCTION_KBD_BACKLIGHT; |
| gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>; |
| label = "white:kbd_backlight"; |
| retain-state-suspended; |
| }; |
| |
| caps-lock { |
| color = <LED_COLOR_ID_YELLOW>; |
| default-state = "off"; |
| function = LED_FUNCTION_CAPSLOCK; |
| gpios = <&tlmm 26 GPIO_ACTIVE_HIGH>; |
| label = "yellow:capslock"; |
| linux,default-trigger = "kbd-capslock"; |
| }; |
| }; |
| |
| reserved-memory { |
| cont_splash_mem: memory@9d400000 { |
| reg = <0x0 0x9d400000 0x0 0x2000000>; |
| no-map; |
| }; |
| |
| zap_shader_region: memory@f6400000 { |
| compatible = "shared-dma-pool"; |
| reg = <0x0 0xf6400000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| ramoops@ffc00000 { |
| compatible = "ramoops"; |
| reg = <0x0 0xffc00000 0x0 0x100000>; |
| console-size = <0x60000>; |
| ecc-size = <16>; |
| ftrace-size = <0x10000>; |
| pmsg-size = <0x20000>; |
| record-size = <0x10000>; |
| }; |
| }; |
| |
| ts_vio_vreg: ts-vio-vreg { |
| compatible = "regulator-fixed"; |
| regulator-name = "ts_vio_reg"; |
| startup-delay-us = <2>; |
| enable-active-high; |
| gpio = <&tlmm 81 GPIO_ACTIVE_HIGH>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_vio_default>; |
| regulator-always-on; |
| }; |
| }; |
| |
| &blsp2_i2c1 { |
| status = "ok"; |
| |
| touchscreen@14 { |
| compatible = "goodix,gt9286"; |
| reg = <0x14>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <125 IRQ_TYPE_LEVEL_LOW>; |
| reset-gpios = <&tlmm 89 GPIO_ACTIVE_HIGH>; |
| AVDD28-supply = <&vreg_l28_3p0>; |
| VDDIO-supply = <&ts_vio_vreg>; |
| pinctrl-names = "active"; |
| pinctrl-0 = <&ts_rst_n>, <&ts_int_n>; |
| }; |
| }; |
| |
| &mmcc { |
| status = "ok"; |
| }; |
| |
| &mmss_smmu { |
| status = "ok"; |
| }; |
| |
| &pm8998_gpio { |
| vol_up_pin_a: vol-up-active { |
| pins = "gpio6"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_focus_pin_a: cam-focus-btn-active { |
| pins = "gpio7"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| |
| cam_snapshot_pin_a: cam-snapshot-btn-active { |
| pins = "gpio8"; |
| function = "normal"; |
| bias-pull-up; |
| input-enable; |
| qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| }; |
| }; |
| |
| &pm8998_pon { |
| resin { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| bias-pull-up; |
| debounce = <15625>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| |
| &tlmm { |
| gpio-reserved-ranges = <0 4>; |
| |
| mdp_vsync_n: mdp-vsync-n { |
| pins = "gpio10"; |
| function = "mdp_vsync_a"; |
| bias-pull-down; |
| drive-strength = <2>; |
| }; |
| |
| gpio_kb_pins_extra: gpio-kb-pins-extra { |
| pins = "gpio21", "gpio32", "gpio33", "gpio114", |
| "gpio128", "gpio129"; |
| function = "gpio"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| ts_vio_default: ts-vio-def { |
| pins = "gpio81"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| ts_rst_n: ts-rst-n { |
| pins = "gpio89"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <8>; |
| }; |
| |
| hall_sensor1_default: hall-sensor1-def { |
| pins = "gpio124"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| input-enable; |
| }; |
| |
| ts_int_n: ts-int-n { |
| pins = "gpio125"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <8>; |
| }; |
| }; |
| |
| &ufshc { |
| status = "ok"; |
| }; |
| |
| &ufsphy { |
| status = "ok"; |
| }; |
| |
| &usb3_dwc3 { |
| dr_mode = "peripheral"; |
| extcon = <&extcon_usb>; |
| }; |
| |
| /* GT9286 analog supply */ |
| &vreg_l28_3p0 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
