| * Marvell EBU PCIe interfaces |
| |
| Mandatory properties: |
| |
| - compatible: one of the following values: |
| marvell,armada-370-pcie |
| marvell,armada-xp-pcie |
| marvell,kirkwood-pcie |
| - #address-cells, set to <3> |
| - #size-cells, set to <2> |
| - #interrupt-cells, set to <1> |
| - bus-range: PCI bus numbers covered |
| - device_type, set to "pci" |
| - ranges: ranges describing the MMIO registers to control the PCIe |
| interfaces, and ranges describing the MBus windows needed to access |
| the memory and I/O regions of each PCIe interface. |
| |
| The ranges describing the MMIO registers have the following layout: |
| |
| 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s |
| |
| where: |
| |
| * r is a 32-bits value that gives the offset of the MMIO |
| registers of this PCIe interface, from the base of the internal |
| registers. |
| |
| * s is a 32-bits value that give the size of this MMIO |
| registers area. This range entry translates the '0x82000000 0 r' PCI |
| address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part |
| of the internal register window (as identified by MBUS_ID(0xf0, |
| 0x01)). |
| |
| The ranges describing the MBus windows have the following layout: |
| |
| 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 |
| |
| where: |
| |
| * t is the type of the MBus window (as defined by the standard PCI DT |
| bindings), 1 for I/O and 2 for memory. |
| |
| * s is the PCI slot that corresponds to this PCIe interface |
| |
| * w is the 'target ID' value for the MBus window |
| |
| * a the 'attribute' value for the MBus window. |
| |
| Since the location and size of the different MBus windows is not fixed in |
| hardware, and only determined in runtime, those ranges cover the full first |
| 4 GB of the physical address space, and do not translate into a valid CPU |
| address. |
| |
| In addition, the device tree node must have sub-nodes describing each |
| PCIe interface, having the following mandatory properties: |
| |
| - reg: used only for interrupt mapping, so only the first four bytes |
| are used to refer to the correct bus number and device number. |
| - assigned-addresses: reference to the MMIO registers used to control |
| this PCIe interface. |
| - clocks: the clock associated to this PCIe interface |
| - marvell,pcie-port: the physical PCIe port number |
| - status: either "disabled" or "okay" |
| - device_type, set to "pci" |
| - #address-cells, set to <3> |
| - #size-cells, set to <2> |
| - #interrupt-cells, set to <1> |
| - ranges, translating the MBus windows ranges of the parent node into |
| standard PCI addresses. |
| - interrupt-map-mask and interrupt-map, standard PCI properties to |
| define the mapping of the PCIe interface to interrupt numbers. |
| |
| and the following optional properties: |
| - marvell,pcie-lane: the physical PCIe lane number, for ports having |
| multiple lanes. If this property is not found, we assume that the |
| value is 0. |
| |
| Example: |
| |
| pcie-controller { |
| compatible = "marvell,armada-xp-pcie"; |
| status = "disabled"; |
| device_type = "pci"; |
| |
| #address-cells = <3>; |
| #size-cells = <2>; |
| |
| bus-range = <0x00 0xff>; |
| |
| ranges = |
| <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ |
| 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ |
| 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ |
| 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ |
| 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ |
| 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ |
| 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ |
| 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ |
| 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ |
| 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ |
| 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ |
| 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ |
| 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ |
| 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ |
| 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ |
| 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ |
| 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ |
| 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ |
| |
| 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ |
| 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ |
| 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ |
| 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ |
| 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ |
| 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ |
| 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ |
| 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ |
| |
| 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ |
| 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ |
| |
| 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ |
| 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; |
| |
| pcie@1,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; |
| reg = <0x0800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 |
| 0x81000000 0 0 0x81000000 0x1 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 58>; |
| marvell,pcie-port = <0>; |
| marvell,pcie-lane = <0>; |
| clocks = <&gateclk 5>; |
| status = "disabled"; |
| }; |
| |
| pcie@2,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; |
| reg = <0x1000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 |
| 0x81000000 0 0 0x81000000 0x2 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 59>; |
| marvell,pcie-port = <0>; |
| marvell,pcie-lane = <1>; |
| clocks = <&gateclk 6>; |
| status = "disabled"; |
| }; |
| |
| pcie@3,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; |
| reg = <0x1800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 |
| 0x81000000 0 0 0x81000000 0x3 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 60>; |
| marvell,pcie-port = <0>; |
| marvell,pcie-lane = <2>; |
| clocks = <&gateclk 7>; |
| status = "disabled"; |
| }; |
| |
| pcie@4,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; |
| reg = <0x2000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 |
| 0x81000000 0 0 0x81000000 0x4 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 61>; |
| marvell,pcie-port = <0>; |
| marvell,pcie-lane = <3>; |
| clocks = <&gateclk 8>; |
| status = "disabled"; |
| }; |
| |
| pcie@5,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; |
| reg = <0x2800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 |
| 0x81000000 0 0 0x81000000 0x5 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 62>; |
| marvell,pcie-port = <1>; |
| marvell,pcie-lane = <0>; |
| clocks = <&gateclk 9>; |
| status = "disabled"; |
| }; |
| |
| pcie@6,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; |
| reg = <0x3000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 |
| 0x81000000 0 0 0x81000000 0x6 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 63>; |
| marvell,pcie-port = <1>; |
| marvell,pcie-lane = <1>; |
| clocks = <&gateclk 10>; |
| status = "disabled"; |
| }; |
| |
| pcie@7,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; |
| reg = <0x3800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 |
| 0x81000000 0 0 0x81000000 0x7 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 64>; |
| marvell,pcie-port = <1>; |
| marvell,pcie-lane = <2>; |
| clocks = <&gateclk 11>; |
| status = "disabled"; |
| }; |
| |
| pcie@8,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; |
| reg = <0x4000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 |
| 0x81000000 0 0 0x81000000 0x8 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 65>; |
| marvell,pcie-port = <1>; |
| marvell,pcie-lane = <3>; |
| clocks = <&gateclk 12>; |
| status = "disabled"; |
| }; |
| |
| pcie@9,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; |
| reg = <0x4800 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 |
| 0x81000000 0 0 0x81000000 0x9 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 99>; |
| marvell,pcie-port = <2>; |
| marvell,pcie-lane = <0>; |
| clocks = <&gateclk 26>; |
| status = "disabled"; |
| }; |
| |
| pcie@10,0 { |
| device_type = "pci"; |
| assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; |
| reg = <0x5000 0 0 0 0>; |
| #address-cells = <3>; |
| #size-cells = <2>; |
| #interrupt-cells = <1>; |
| ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 |
| 0x81000000 0 0 0x81000000 0xa 0 1 0>; |
| interrupt-map-mask = <0 0 0 0>; |
| interrupt-map = <0 0 0 0 &mpic 103>; |
| marvell,pcie-port = <3>; |
| marvell,pcie-lane = <0>; |
| clocks = <&gateclk 27>; |
| status = "disabled"; |
| }; |
| }; |