| // SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| /* |
| * Copyright 2020 Compass Electronics Group, LLC |
| */ |
| |
| / { |
| aliases { |
| rtc0 = &rtc; |
| rtc1 = &snvs_rtc; |
| }; |
| |
| usdhc1_pwrseq: usdhc1_pwrseq { |
| compatible = "mmc-pwrseq-simple"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_usdhc1_gpio>; |
| reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; |
| clocks = <&osc_32k>; |
| clock-names = "ext_clock"; |
| post-power-on-delay-ms = <80>; |
| }; |
| |
| memory@40000000 { |
| device_type = "memory"; |
| reg = <0x0 0x40000000 0 0x80000000>; |
| }; |
| }; |
| |
| &A53_0 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_1 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_2 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &A53_3 { |
| cpu-supply = <&buck2_reg>; |
| }; |
| |
| &ddrc { |
| operating-points-v2 = <&ddrc_opp_table>; |
| |
| ddrc_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-25M { |
| opp-hz = /bits/ 64 <25000000>; |
| }; |
| |
| opp-100M { |
| opp-hz = /bits/ 64 <100000000>; |
| }; |
| |
| opp-750M { |
| opp-hz = /bits/ 64 <750000000>; |
| }; |
| }; |
| }; |
| |
| &fec1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_fec1>; |
| phy-mode = "rgmii-id"; |
| phy-handle = <ðphy0>; |
| fsl,magic-packet; |
| status = "okay"; |
| |
| mdio { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ethphy0: ethernet-phy@0 { |
| compatible = "ethernet-phy-ieee802.3-c22"; |
| reg = <0>; |
| }; |
| }; |
| }; |
| |
| &flexspi { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_flexspi>; |
| status = "okay"; |
| |
| flash@0 { |
| reg = <0>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| compatible = "jedec,spi-nor"; |
| spi-max-frequency = <80000000>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <4>; |
| }; |
| }; |
| |
| &i2c1 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c1>; |
| status = "okay"; |
| |
| pmic@4b { |
| compatible = "rohm,bd71847"; |
| reg = <0x4b>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_pmic>; |
| interrupt-parent = <&gpio1>; |
| interrupts = <3 IRQ_TYPE_LEVEL_LOW>; |
| rohm,reset-snvs-powered; |
| |
| #clock-cells = <0>; |
| clocks = <&osc_32k 0>; |
| clock-output-names = "clk-32k-out"; |
| |
| regulators { |
| buck1_reg: BUCK1 { |
| regulator-name = "buck1"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| }; |
| |
| buck2_reg: BUCK2 { |
| regulator-name = "buck2"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| regulator-ramp-delay = <1250>; |
| rohm,dvs-run-voltage = <1000000>; |
| rohm,dvs-idle-voltage = <900000>; |
| }; |
| |
| buck3_reg: BUCK3 { |
| // BUCK5 in datasheet |
| regulator-name = "buck3"; |
| regulator-min-microvolt = <700000>; |
| regulator-max-microvolt = <1350000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck4_reg: BUCK4 { |
| // BUCK6 in datasheet |
| regulator-name = "buck4"; |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck5_reg: BUCK5 { |
| // BUCK7 in datasheet |
| regulator-name = "buck5"; |
| regulator-min-microvolt = <1605000>; |
| regulator-max-microvolt = <1995000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| buck6_reg: BUCK6 { |
| // BUCK8 in datasheet |
| regulator-name = "buck6"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <1400000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo1_reg: LDO1 { |
| regulator-name = "ldo1"; |
| regulator-min-microvolt = <1600000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo2_reg: LDO2 { |
| regulator-name = "ldo2"; |
| regulator-min-microvolt = <800000>; |
| regulator-max-microvolt = <900000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo3_reg: LDO3 { |
| regulator-name = "ldo3"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo4_reg: LDO4 { |
| regulator-name = "ldo4"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| |
| ldo6_reg: LDO6 { |
| regulator-name = "ldo6"; |
| regulator-min-microvolt = <900000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-boot-on; |
| regulator-always-on; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c3 { |
| clock-frequency = <400000>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_i2c3>; |
| status = "okay"; |
| |
| eeprom@50 { |
| compatible = "microchip,24c64", "atmel,24c64"; |
| pagesize = <32>; |
| read-only; /* Manufacturing EEPROM programmed at factory */ |
| reg = <0x50>; |
| }; |
| |
| rtc: rtc@51 { |
| compatible = "nxp,pcf85263"; |
| reg = <0x51>; |
| }; |
| }; |
| |
| &uart1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_uart1>; |
| assigned-clocks = <&clk IMX8MM_CLK_UART1>; |
| assigned-clock-parents = <&clk IMX8MM_SYS_PLL1_80M>; |
| uart-has-rtscts; |
| status = "okay"; |
| |
| bluetooth { |
| compatible = "brcm,bcm43438-bt"; |
| shutdown-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; |
| host-wakeup-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; |
| device-wakeup-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>; |
| clocks = <&osc_32k>; |
| max-speed = <4000000>; |
| clock-names = "extclk"; |
| }; |
| }; |
| |
| &usdhc1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc1>; |
| pinctrl-1 = <&pinctrl_usdhc1_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc1_200mhz>; |
| bus-width = <4>; |
| non-removable; |
| cap-power-off-card; |
| pm-ignore-notify; |
| keep-power-in-suspend; |
| mmc-pwrseq = <&usdhc1_pwrseq>; |
| status = "okay"; |
| |
| brcmf: bcrmf@1 { |
| reg = <1>; |
| compatible = "brcm,bcm4329-fmac"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wlan>; |
| interrupt-parent = <&gpio2>; |
| interrupts = <9 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "host-wake"; |
| }; |
| }; |
| |
| &usdhc3 { |
| pinctrl-names = "default", "state_100mhz", "state_200mhz"; |
| pinctrl-0 = <&pinctrl_usdhc3>; |
| pinctrl-1 = <&pinctrl_usdhc3_100mhz>; |
| pinctrl-2 = <&pinctrl_usdhc3_200mhz>; |
| bus-width = <8>; |
| non-removable; |
| status = "okay"; |
| }; |
| |
| &wdog1 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&pinctrl_wdog>; |
| fsl,ext-reset-output; |
| status = "okay"; |
| }; |
| |
| &iomuxc { |
| pinctrl_fec1: fec1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3 |
| MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3 |
| MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f |
| MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f |
| MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f |
| MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f |
| MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91 |
| MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91 |
| MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91 |
| MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91 |
| MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f |
| MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91 |
| MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91 |
| MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f |
| MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x19 |
| >; |
| }; |
| |
| pinctrl_i2c1: i2c1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_i2c3: i2c3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3 |
| MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3 |
| >; |
| }; |
| |
| pinctrl_flexspi: flexspigrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_ALE_QSPI_A_SCLK 0x1c2 |
| MX8MM_IOMUXC_NAND_CE0_B_QSPI_A_SS0_B 0x82 |
| MX8MM_IOMUXC_NAND_DATA00_QSPI_A_DATA0 0x82 |
| MX8MM_IOMUXC_NAND_DATA01_QSPI_A_DATA1 0x82 |
| MX8MM_IOMUXC_NAND_DATA02_QSPI_A_DATA2 0x82 |
| MX8MM_IOMUXC_NAND_DATA03_QSPI_A_DATA3 0x82 |
| >; |
| }; |
| |
| pinctrl_pmic: pmicirqgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x141 |
| >; |
| }; |
| |
| pinctrl_uart1: uart1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_UART1_RXD_UART1_DCE_RX 0x140 |
| MX8MM_IOMUXC_UART1_TXD_UART1_DCE_TX 0x140 |
| MX8MM_IOMUXC_UART3_RXD_UART1_DCE_CTS_B 0x140 |
| MX8MM_IOMUXC_UART3_TXD_UART1_DCE_RTS_B 0x140 |
| MX8MM_IOMUXC_SD1_DATA4_GPIO2_IO6 0x19 |
| MX8MM_IOMUXC_SD1_DATA5_GPIO2_IO7 0x19 |
| MX8MM_IOMUXC_SD1_DATA6_GPIO2_IO8 0x19 |
| MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x141 |
| >; |
| }; |
| |
| pinctrl_usdhc1_gpio: usdhc1gpiogrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x41 |
| >; |
| }; |
| |
| pinctrl_usdhc1: usdhc1grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0 |
| >; |
| }; |
| |
| pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4 |
| >; |
| }; |
| |
| pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196 |
| MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6 |
| MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6 |
| >; |
| }; |
| |
| pinctrl_usdhc3: usdhc3grp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d0 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d0 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d0 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d0 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x190 |
| >; |
| }; |
| |
| pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d4 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d4 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d4 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d4 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x194 |
| >; |
| }; |
| |
| pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196 |
| MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6 |
| MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6 |
| MX8MM_IOMUXC_NAND_RE_B_USDHC3_DATA4 0x1d6 |
| MX8MM_IOMUXC_NAND_CE2_B_USDHC3_DATA5 0x1d6 |
| MX8MM_IOMUXC_NAND_CE3_B_USDHC3_DATA6 0x1d6 |
| MX8MM_IOMUXC_NAND_CLE_USDHC3_DATA7 0x1d6 |
| MX8MM_IOMUXC_NAND_CE1_B_USDHC3_STROBE 0x196 |
| >; |
| }; |
| |
| pinctrl_wdog: wdoggrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x166 |
| >; |
| }; |
| |
| pinctrl_wlan: wlangrp { |
| fsl,pins = < |
| MX8MM_IOMUXC_SD1_DATA7_GPIO2_IO9 0x111 |
| >; |
| }; |
| }; |
