| // SPDX-License-Identifier: GPL-2.0+ |
| // |
| // Security related flags and so on. |
| // |
| // Copyright 2018, Michael Ellerman, IBM Corporation. |
| |
| #include <linux/cpu.h> |
| #include <linux/kernel.h> |
| #include <linux/device.h> |
| #include <linux/memblock.h> |
| #include <linux/nospec.h> |
| #include <linux/prctl.h> |
| #include <linux/seq_buf.h> |
| #include <linux/debugfs.h> |
| |
| #include <asm/asm-prototypes.h> |
| #include <asm/code-patching.h> |
| #include <asm/security_features.h> |
| #include <asm/setup.h> |
| #include <asm/inst.h> |
| |
| #include "setup.h" |
| |
| u64 powerpc_security_features __read_mostly = SEC_FTR_DEFAULT; |
| |
| enum branch_cache_flush_type { |
| BRANCH_CACHE_FLUSH_NONE = 0x1, |
| BRANCH_CACHE_FLUSH_SW = 0x2, |
| BRANCH_CACHE_FLUSH_HW = 0x4, |
| }; |
| static enum branch_cache_flush_type count_cache_flush_type = BRANCH_CACHE_FLUSH_NONE; |
| static enum branch_cache_flush_type link_stack_flush_type = BRANCH_CACHE_FLUSH_NONE; |
| |
| bool barrier_nospec_enabled; |
| static bool no_nospec; |
| static bool btb_flush_enabled; |
| #if defined(CONFIG_PPC_FSL_BOOK3E) || defined(CONFIG_PPC_BOOK3S_64) |
| static bool no_spectrev2; |
| #endif |
| |
| static void enable_barrier_nospec(bool enable) |
| { |
| barrier_nospec_enabled = enable; |
| do_barrier_nospec_fixups(enable); |
| } |
| |
| void setup_barrier_nospec(void) |
| { |
| bool enable; |
| |
| /* |
| * It would make sense to check SEC_FTR_SPEC_BAR_ORI31 below as well. |
| * But there's a good reason not to. The two flags we check below are |
| * both are enabled by default in the kernel, so if the hcall is not |
| * functional they will be enabled. |
| * On a system where the host firmware has been updated (so the ori |
| * functions as a barrier), but on which the hypervisor (KVM/Qemu) has |
| * not been updated, we would like to enable the barrier. Dropping the |
| * check for SEC_FTR_SPEC_BAR_ORI31 achieves that. The only downside is |
| * we potentially enable the barrier on systems where the host firmware |
| * is not updated, but that's harmless as it's a no-op. |
| */ |
| enable = security_ftr_enabled(SEC_FTR_FAVOUR_SECURITY) && |
| security_ftr_enabled(SEC_FTR_BNDS_CHK_SPEC_BAR); |
| |
| if (!no_nospec && !cpu_mitigations_off()) |
| enable_barrier_nospec(enable); |
| } |
| |
| static int __init handle_nospectre_v1(char *p) |
| { |
| no_nospec = true; |
| |
| return 0; |
| } |
| early_param("nospectre_v1", handle_nospectre_v1); |
| |
| #ifdef CONFIG_DEBUG_FS |
| static int barrier_nospec_set(void *data, u64 val) |
| { |
| switch (val) { |
| case 0: |
| case 1: |
| break; |
| default: |
| return -EINVAL; |
| } |
| |
| if (!!val == !!barrier_nospec_enabled) |
| return 0; |
| |
| enable_barrier_nospec(!!val); |
| |
| return 0; |
| } |
| |
| static int barrier_nospec_get(void *data, u64 *val) |
| { |
| *val = barrier_nospec_enabled ? 1 : 0; |
| return 0; |
| } |
| |
| DEFINE_DEBUGFS_ATTRIBUTE(fops_barrier_nospec, barrier_nospec_get, |
| barrier_nospec_set, "%llu\n"); |
| |
| static __init int barrier_nospec_debugfs_init(void) |
| { |
| debugfs_create_file_unsafe("barrier_nospec", 0600, |
| arch_debugfs_dir, NULL, |
| &fops_barrier_nospec); |
| return 0; |
| } |
| device_initcall(barrier_nospec_debugfs_init); |
| |
| static __init int security_feature_debugfs_init(void) |
| { |
| debugfs_create_x64("security_features", 0400, arch_debugfs_dir, |
| &powerpc_security_features); |
| return 0; |
| } |
| device_initcall(security_feature_debugfs_init); |
| #endif /* CONFIG_DEBUG_FS */ |
| |
| #if defined(CONFIG_PPC_FSL_BOOK3E) || defined(CONFIG_PPC_BOOK3S_64) |
| static int __init handle_nospectre_v2(char *p) |
| { |
| no_spectrev2 = true; |
| |
| return 0; |
| } |
| early_param("nospectre_v2", handle_nospectre_v2); |
| #endif /* CONFIG_PPC_FSL_BOOK3E || CONFIG_PPC_BOOK3S_64 */ |
| |
| #ifdef CONFIG_PPC_FSL_BOOK3E |
| void setup_spectre_v2(void) |
| { |
| if (no_spectrev2 || cpu_mitigations_off()) |
| do_btb_flush_fixups(); |
| else |
| btb_flush_enabled = true; |
| } |
| #endif /* CONFIG_PPC_FSL_BOOK3E */ |
| |
| #ifdef CONFIG_PPC_BOOK3S_64 |
| ssize_t cpu_show_meltdown(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| bool thread_priv; |
| |
| thread_priv = security_ftr_enabled(SEC_FTR_L1D_THREAD_PRIV); |
| |
| if (rfi_flush) { |
| struct seq_buf s; |
| seq_buf_init(&s, buf, PAGE_SIZE - 1); |
| |
| seq_buf_printf(&s, "Mitigation: RFI Flush"); |
| if (thread_priv) |
| seq_buf_printf(&s, ", L1D private per thread"); |
| |
| seq_buf_printf(&s, "\n"); |
| |
| return s.len; |
| } |
| |
| if (thread_priv) |
| return sprintf(buf, "Vulnerable: L1D private per thread\n"); |
| |
| if (!security_ftr_enabled(SEC_FTR_L1D_FLUSH_HV) && |
| !security_ftr_enabled(SEC_FTR_L1D_FLUSH_PR)) |
| return sprintf(buf, "Not affected\n"); |
| |
| return sprintf(buf, "Vulnerable\n"); |
| } |
| |
| ssize_t cpu_show_l1tf(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| return cpu_show_meltdown(dev, attr, buf); |
| } |
| #endif |
| |
| ssize_t cpu_show_spectre_v1(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct seq_buf s; |
| |
| seq_buf_init(&s, buf, PAGE_SIZE - 1); |
| |
| if (security_ftr_enabled(SEC_FTR_BNDS_CHK_SPEC_BAR)) { |
| if (barrier_nospec_enabled) |
| seq_buf_printf(&s, "Mitigation: __user pointer sanitization"); |
| else |
| seq_buf_printf(&s, "Vulnerable"); |
| |
| if (security_ftr_enabled(SEC_FTR_SPEC_BAR_ORI31)) |
| seq_buf_printf(&s, ", ori31 speculation barrier enabled"); |
| |
| seq_buf_printf(&s, "\n"); |
| } else |
| seq_buf_printf(&s, "Not affected\n"); |
| |
| return s.len; |
| } |
| |
| ssize_t cpu_show_spectre_v2(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct seq_buf s; |
| bool bcs, ccd; |
| |
| seq_buf_init(&s, buf, PAGE_SIZE - 1); |
| |
| bcs = security_ftr_enabled(SEC_FTR_BCCTRL_SERIALISED); |
| ccd = security_ftr_enabled(SEC_FTR_COUNT_CACHE_DISABLED); |
| |
| if (bcs || ccd) { |
| seq_buf_printf(&s, "Mitigation: "); |
| |
| if (bcs) |
| seq_buf_printf(&s, "Indirect branch serialisation (kernel only)"); |
| |
| if (bcs && ccd) |
| seq_buf_printf(&s, ", "); |
| |
| if (ccd) |
| seq_buf_printf(&s, "Indirect branch cache disabled"); |
| |
| } else if (count_cache_flush_type != BRANCH_CACHE_FLUSH_NONE) { |
| seq_buf_printf(&s, "Mitigation: Software count cache flush"); |
| |
| if (count_cache_flush_type == BRANCH_CACHE_FLUSH_HW) |
| seq_buf_printf(&s, " (hardware accelerated)"); |
| |
| } else if (btb_flush_enabled) { |
| seq_buf_printf(&s, "Mitigation: Branch predictor state flush"); |
| } else { |
| seq_buf_printf(&s, "Vulnerable"); |
| } |
| |
| if (bcs || ccd || count_cache_flush_type != BRANCH_CACHE_FLUSH_NONE) { |
| if (link_stack_flush_type != BRANCH_CACHE_FLUSH_NONE) |
| seq_buf_printf(&s, ", Software link stack flush"); |
| if (link_stack_flush_type == BRANCH_CACHE_FLUSH_HW) |
| seq_buf_printf(&s, " (hardware accelerated)"); |
| } |
| |
| seq_buf_printf(&s, "\n"); |
| |
| return s.len; |
| } |
| |
| #ifdef CONFIG_PPC_BOOK3S_64 |
| /* |
| * Store-forwarding barrier support. |
| */ |
| |
| static enum stf_barrier_type stf_enabled_flush_types; |
| static bool no_stf_barrier; |
| static bool stf_barrier; |
| |
| static int __init handle_no_stf_barrier(char *p) |
| { |
| pr_info("stf-barrier: disabled on command line."); |
| no_stf_barrier = true; |
| return 0; |
| } |
| |
| early_param("no_stf_barrier", handle_no_stf_barrier); |
| |
| enum stf_barrier_type stf_barrier_type_get(void) |
| { |
| return stf_enabled_flush_types; |
| } |
| |
| /* This is the generic flag used by other architectures */ |
| static int __init handle_ssbd(char *p) |
| { |
| if (!p || strncmp(p, "auto", 5) == 0 || strncmp(p, "on", 2) == 0 ) { |
| /* Until firmware tells us, we have the barrier with auto */ |
| return 0; |
| } else if (strncmp(p, "off", 3) == 0) { |
| handle_no_stf_barrier(NULL); |
| return 0; |
| } else |
| return 1; |
| |
| return 0; |
| } |
| early_param("spec_store_bypass_disable", handle_ssbd); |
| |
| /* This is the generic flag used by other architectures */ |
| static int __init handle_no_ssbd(char *p) |
| { |
| handle_no_stf_barrier(NULL); |
| return 0; |
| } |
| early_param("nospec_store_bypass_disable", handle_no_ssbd); |
| |
| static void stf_barrier_enable(bool enable) |
| { |
| if (enable) |
| do_stf_barrier_fixups(stf_enabled_flush_types); |
| else |
| do_stf_barrier_fixups(STF_BARRIER_NONE); |
| |
| stf_barrier = enable; |
| } |
| |
| void setup_stf_barrier(void) |
| { |
| enum stf_barrier_type type; |
| bool enable; |
| |
| /* Default to fallback in case fw-features are not available */ |
| if (cpu_has_feature(CPU_FTR_ARCH_300)) |
| type = STF_BARRIER_EIEIO; |
| else if (cpu_has_feature(CPU_FTR_ARCH_207S)) |
| type = STF_BARRIER_SYNC_ORI; |
| else if (cpu_has_feature(CPU_FTR_ARCH_206)) |
| type = STF_BARRIER_FALLBACK; |
| else |
| type = STF_BARRIER_NONE; |
| |
| enable = security_ftr_enabled(SEC_FTR_FAVOUR_SECURITY) && |
| security_ftr_enabled(SEC_FTR_STF_BARRIER); |
| |
| if (type == STF_BARRIER_FALLBACK) { |
| pr_info("stf-barrier: fallback barrier available\n"); |
| } else if (type == STF_BARRIER_SYNC_ORI) { |
| pr_info("stf-barrier: hwsync barrier available\n"); |
| } else if (type == STF_BARRIER_EIEIO) { |
| pr_info("stf-barrier: eieio barrier available\n"); |
| } |
| |
| stf_enabled_flush_types = type; |
| |
| if (!no_stf_barrier && !cpu_mitigations_off()) |
| stf_barrier_enable(enable); |
| } |
| |
| ssize_t cpu_show_spec_store_bypass(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| if (stf_barrier && stf_enabled_flush_types != STF_BARRIER_NONE) { |
| const char *type; |
| switch (stf_enabled_flush_types) { |
| case STF_BARRIER_EIEIO: |
| type = "eieio"; |
| break; |
| case STF_BARRIER_SYNC_ORI: |
| type = "hwsync"; |
| break; |
| case STF_BARRIER_FALLBACK: |
| type = "fallback"; |
| break; |
| default: |
| type = "unknown"; |
| } |
| return sprintf(buf, "Mitigation: Kernel entry/exit barrier (%s)\n", type); |
| } |
| |
| if (!security_ftr_enabled(SEC_FTR_L1D_FLUSH_HV) && |
| !security_ftr_enabled(SEC_FTR_L1D_FLUSH_PR)) |
| return sprintf(buf, "Not affected\n"); |
| |
| return sprintf(buf, "Vulnerable\n"); |
| } |
| |
| static int ssb_prctl_get(struct task_struct *task) |
| { |
| if (stf_enabled_flush_types == STF_BARRIER_NONE) |
| /* |
| * We don't have an explicit signal from firmware that we're |
| * vulnerable or not, we only have certain CPU revisions that |
| * are known to be vulnerable. |
| * |
| * We assume that if we're on another CPU, where the barrier is |
| * NONE, then we are not vulnerable. |
| */ |
| return PR_SPEC_NOT_AFFECTED; |
| else |
| /* |
| * If we do have a barrier type then we are vulnerable. The |
| * barrier is not a global or per-process mitigation, so the |
| * only value we can report here is PR_SPEC_ENABLE, which |
| * appears as "vulnerable" in /proc. |
| */ |
| return PR_SPEC_ENABLE; |
| |
| return -EINVAL; |
| } |
| |
| int arch_prctl_spec_ctrl_get(struct task_struct *task, unsigned long which) |
| { |
| switch (which) { |
| case PR_SPEC_STORE_BYPASS: |
| return ssb_prctl_get(task); |
| default: |
| return -ENODEV; |
| } |
| } |
| |
| #ifdef CONFIG_DEBUG_FS |
| static int stf_barrier_set(void *data, u64 val) |
| { |
| bool enable; |
| |
| if (val == 1) |
| enable = true; |
| else if (val == 0) |
| enable = false; |
| else |
| return -EINVAL; |
| |
| /* Only do anything if we're changing state */ |
| if (enable != stf_barrier) |
| stf_barrier_enable(enable); |
| |
| return 0; |
| } |
| |
| static int stf_barrier_get(void *data, u64 *val) |
| { |
| *val = stf_barrier ? 1 : 0; |
| return 0; |
| } |
| |
| DEFINE_DEBUGFS_ATTRIBUTE(fops_stf_barrier, stf_barrier_get, stf_barrier_set, |
| "%llu\n"); |
| |
| static __init int stf_barrier_debugfs_init(void) |
| { |
| debugfs_create_file_unsafe("stf_barrier", 0600, arch_debugfs_dir, |
| NULL, &fops_stf_barrier); |
| return 0; |
| } |
| device_initcall(stf_barrier_debugfs_init); |
| #endif /* CONFIG_DEBUG_FS */ |
| |
| static void update_branch_cache_flush(void) |
| { |
| u32 *site, __maybe_unused *site2; |
| |
| #ifdef CONFIG_KVM_BOOK3S_HV_POSSIBLE |
| site = &patch__call_kvm_flush_link_stack; |
| site2 = &patch__call_kvm_flush_link_stack_p9; |
| // This controls the branch from guest_exit_cont to kvm_flush_link_stack |
| if (link_stack_flush_type == BRANCH_CACHE_FLUSH_NONE) { |
| patch_instruction_site(site, ppc_inst(PPC_RAW_NOP())); |
| patch_instruction_site(site2, ppc_inst(PPC_RAW_NOP())); |
| } else { |
| // Could use HW flush, but that could also flush count cache |
| patch_branch_site(site, (u64)&kvm_flush_link_stack, BRANCH_SET_LINK); |
| patch_branch_site(site2, (u64)&kvm_flush_link_stack, BRANCH_SET_LINK); |
| } |
| #endif |
| |
| // Patch out the bcctr first, then nop the rest |
| site = &patch__call_flush_branch_caches3; |
| patch_instruction_site(site, ppc_inst(PPC_RAW_NOP())); |
| site = &patch__call_flush_branch_caches2; |
| patch_instruction_site(site, ppc_inst(PPC_RAW_NOP())); |
| site = &patch__call_flush_branch_caches1; |
| patch_instruction_site(site, ppc_inst(PPC_RAW_NOP())); |
| |
| // This controls the branch from _switch to flush_branch_caches |
| if (count_cache_flush_type == BRANCH_CACHE_FLUSH_NONE && |
| link_stack_flush_type == BRANCH_CACHE_FLUSH_NONE) { |
| // Nothing to be done |
| |
| } else if (count_cache_flush_type == BRANCH_CACHE_FLUSH_HW && |
| link_stack_flush_type == BRANCH_CACHE_FLUSH_HW) { |
| // Patch in the bcctr last |
| site = &patch__call_flush_branch_caches1; |
| patch_instruction_site(site, ppc_inst(0x39207fff)); // li r9,0x7fff |
| site = &patch__call_flush_branch_caches2; |
| patch_instruction_site(site, ppc_inst(0x7d2903a6)); // mtctr r9 |
| site = &patch__call_flush_branch_caches3; |
| patch_instruction_site(site, ppc_inst(PPC_INST_BCCTR_FLUSH)); |
| |
| } else { |
| patch_branch_site(site, (u64)&flush_branch_caches, BRANCH_SET_LINK); |
| |
| // If we just need to flush the link stack, early return |
| if (count_cache_flush_type == BRANCH_CACHE_FLUSH_NONE) { |
| patch_instruction_site(&patch__flush_link_stack_return, |
| ppc_inst(PPC_RAW_BLR())); |
| |
| // If we have flush instruction, early return |
| } else if (count_cache_flush_type == BRANCH_CACHE_FLUSH_HW) { |
| patch_instruction_site(&patch__flush_count_cache_return, |
| ppc_inst(PPC_RAW_BLR())); |
| } |
| } |
| } |
| |
| static void toggle_branch_cache_flush(bool enable) |
| { |
| if (!enable || !security_ftr_enabled(SEC_FTR_FLUSH_COUNT_CACHE)) { |
| if (count_cache_flush_type != BRANCH_CACHE_FLUSH_NONE) |
| count_cache_flush_type = BRANCH_CACHE_FLUSH_NONE; |
| |
| pr_info("count-cache-flush: flush disabled.\n"); |
| } else { |
| if (security_ftr_enabled(SEC_FTR_BCCTR_FLUSH_ASSIST)) { |
| count_cache_flush_type = BRANCH_CACHE_FLUSH_HW; |
| pr_info("count-cache-flush: hardware flush enabled.\n"); |
| } else { |
| count_cache_flush_type = BRANCH_CACHE_FLUSH_SW; |
| pr_info("count-cache-flush: software flush enabled.\n"); |
| } |
| } |
| |
| if (!enable || !security_ftr_enabled(SEC_FTR_FLUSH_LINK_STACK)) { |
| if (link_stack_flush_type != BRANCH_CACHE_FLUSH_NONE) |
| link_stack_flush_type = BRANCH_CACHE_FLUSH_NONE; |
| |
| pr_info("link-stack-flush: flush disabled.\n"); |
| } else { |
| if (security_ftr_enabled(SEC_FTR_BCCTR_LINK_FLUSH_ASSIST)) { |
| link_stack_flush_type = BRANCH_CACHE_FLUSH_HW; |
| pr_info("link-stack-flush: hardware flush enabled.\n"); |
| } else { |
| link_stack_flush_type = BRANCH_CACHE_FLUSH_SW; |
| pr_info("link-stack-flush: software flush enabled.\n"); |
| } |
| } |
| |
| update_branch_cache_flush(); |
| } |
| |
| void setup_count_cache_flush(void) |
| { |
| bool enable = true; |
| |
| if (no_spectrev2 || cpu_mitigations_off()) { |
| if (security_ftr_enabled(SEC_FTR_BCCTRL_SERIALISED) || |
| security_ftr_enabled(SEC_FTR_COUNT_CACHE_DISABLED)) |
| pr_warn("Spectre v2 mitigations not fully under software control, can't disable\n"); |
| |
| enable = false; |
| } |
| |
| /* |
| * There's no firmware feature flag/hypervisor bit to tell us we need to |
| * flush the link stack on context switch. So we set it here if we see |
| * either of the Spectre v2 mitigations that aim to protect userspace. |
| */ |
| if (security_ftr_enabled(SEC_FTR_COUNT_CACHE_DISABLED) || |
| security_ftr_enabled(SEC_FTR_FLUSH_COUNT_CACHE)) |
| security_ftr_set(SEC_FTR_FLUSH_LINK_STACK); |
| |
| toggle_branch_cache_flush(enable); |
| } |
| |
| static enum l1d_flush_type enabled_flush_types; |
| static void *l1d_flush_fallback_area; |
| static bool no_rfi_flush; |
| static bool no_entry_flush; |
| static bool no_uaccess_flush; |
| bool rfi_flush; |
| static bool entry_flush; |
| static bool uaccess_flush; |
| DEFINE_STATIC_KEY_FALSE(uaccess_flush_key); |
| EXPORT_SYMBOL(uaccess_flush_key); |
| |
| static int __init handle_no_rfi_flush(char *p) |
| { |
| pr_info("rfi-flush: disabled on command line."); |
| no_rfi_flush = true; |
| return 0; |
| } |
| early_param("no_rfi_flush", handle_no_rfi_flush); |
| |
| static int __init handle_no_entry_flush(char *p) |
| { |
| pr_info("entry-flush: disabled on command line."); |
| no_entry_flush = true; |
| return 0; |
| } |
| early_param("no_entry_flush", handle_no_entry_flush); |
| |
| static int __init handle_no_uaccess_flush(char *p) |
| { |
| pr_info("uaccess-flush: disabled on command line."); |
| no_uaccess_flush = true; |
| return 0; |
| } |
| early_param("no_uaccess_flush", handle_no_uaccess_flush); |
| |
| /* |
| * The RFI flush is not KPTI, but because users will see doco that says to use |
| * nopti we hijack that option here to also disable the RFI flush. |
| */ |
| static int __init handle_no_pti(char *p) |
| { |
| pr_info("rfi-flush: disabling due to 'nopti' on command line.\n"); |
| handle_no_rfi_flush(NULL); |
| return 0; |
| } |
| early_param("nopti", handle_no_pti); |
| |
| static void do_nothing(void *unused) |
| { |
| /* |
| * We don't need to do the flush explicitly, just enter+exit kernel is |
| * sufficient, the RFI exit handlers will do the right thing. |
| */ |
| } |
| |
| void rfi_flush_enable(bool enable) |
| { |
| if (enable) { |
| do_rfi_flush_fixups(enabled_flush_types); |
| on_each_cpu(do_nothing, NULL, 1); |
| } else |
| do_rfi_flush_fixups(L1D_FLUSH_NONE); |
| |
| rfi_flush = enable; |
| } |
| |
| static void entry_flush_enable(bool enable) |
| { |
| if (enable) { |
| do_entry_flush_fixups(enabled_flush_types); |
| on_each_cpu(do_nothing, NULL, 1); |
| } else { |
| do_entry_flush_fixups(L1D_FLUSH_NONE); |
| } |
| |
| entry_flush = enable; |
| } |
| |
| static void uaccess_flush_enable(bool enable) |
| { |
| if (enable) { |
| do_uaccess_flush_fixups(enabled_flush_types); |
| static_branch_enable(&uaccess_flush_key); |
| on_each_cpu(do_nothing, NULL, 1); |
| } else { |
| static_branch_disable(&uaccess_flush_key); |
| do_uaccess_flush_fixups(L1D_FLUSH_NONE); |
| } |
| |
| uaccess_flush = enable; |
| } |
| |
| static void __ref init_fallback_flush(void) |
| { |
| u64 l1d_size, limit; |
| int cpu; |
| |
| /* Only allocate the fallback flush area once (at boot time). */ |
| if (l1d_flush_fallback_area) |
| return; |
| |
| l1d_size = ppc64_caches.l1d.size; |
| |
| /* |
| * If there is no d-cache-size property in the device tree, l1d_size |
| * could be zero. That leads to the loop in the asm wrapping around to |
| * 2^64-1, and then walking off the end of the fallback area and |
| * eventually causing a page fault which is fatal. Just default to |
| * something vaguely sane. |
| */ |
| if (!l1d_size) |
| l1d_size = (64 * 1024); |
| |
| limit = min(ppc64_bolted_size(), ppc64_rma_size); |
| |
| /* |
| * Align to L1d size, and size it at 2x L1d size, to catch possible |
| * hardware prefetch runoff. We don't have a recipe for load patterns to |
| * reliably avoid the prefetcher. |
| */ |
| l1d_flush_fallback_area = memblock_alloc_try_nid(l1d_size * 2, |
| l1d_size, MEMBLOCK_LOW_LIMIT, |
| limit, NUMA_NO_NODE); |
| if (!l1d_flush_fallback_area) |
| panic("%s: Failed to allocate %llu bytes align=0x%llx max_addr=%pa\n", |
| __func__, l1d_size * 2, l1d_size, &limit); |
| |
| |
| for_each_possible_cpu(cpu) { |
| struct paca_struct *paca = paca_ptrs[cpu]; |
| paca->rfi_flush_fallback_area = l1d_flush_fallback_area; |
| paca->l1d_flush_size = l1d_size; |
| } |
| } |
| |
| void setup_rfi_flush(enum l1d_flush_type types, bool enable) |
| { |
| if (types & L1D_FLUSH_FALLBACK) { |
| pr_info("rfi-flush: fallback displacement flush available\n"); |
| init_fallback_flush(); |
| } |
| |
| if (types & L1D_FLUSH_ORI) |
| pr_info("rfi-flush: ori type flush available\n"); |
| |
| if (types & L1D_FLUSH_MTTRIG) |
| pr_info("rfi-flush: mttrig type flush available\n"); |
| |
| enabled_flush_types = types; |
| |
| if (!cpu_mitigations_off() && !no_rfi_flush) |
| rfi_flush_enable(enable); |
| } |
| |
| void setup_entry_flush(bool enable) |
| { |
| if (cpu_mitigations_off()) |
| return; |
| |
| if (!no_entry_flush) |
| entry_flush_enable(enable); |
| } |
| |
| void setup_uaccess_flush(bool enable) |
| { |
| if (cpu_mitigations_off()) |
| return; |
| |
| if (!no_uaccess_flush) |
| uaccess_flush_enable(enable); |
| } |
| |
| #ifdef CONFIG_DEBUG_FS |
| static int count_cache_flush_set(void *data, u64 val) |
| { |
| bool enable; |
| |
| if (val == 1) |
| enable = true; |
| else if (val == 0) |
| enable = false; |
| else |
| return -EINVAL; |
| |
| toggle_branch_cache_flush(enable); |
| |
| return 0; |
| } |
| |
| static int count_cache_flush_get(void *data, u64 *val) |
| { |
| if (count_cache_flush_type == BRANCH_CACHE_FLUSH_NONE) |
| *val = 0; |
| else |
| *val = 1; |
| |
| return 0; |
| } |
| |
| DEFINE_DEBUGFS_ATTRIBUTE(fops_count_cache_flush, count_cache_flush_get, |
| count_cache_flush_set, "%llu\n"); |
| |
| static __init int count_cache_flush_debugfs_init(void) |
| { |
| debugfs_create_file_unsafe("count_cache_flush", 0600, |
| arch_debugfs_dir, NULL, |
| &fops_count_cache_flush); |
| return 0; |
| } |
| device_initcall(count_cache_flush_debugfs_init); |
| |
| static int rfi_flush_set(void *data, u64 val) |
| { |
| bool enable; |
| |
| if (val == 1) |
| enable = true; |
| else if (val == 0) |
| enable = false; |
| else |
| return -EINVAL; |
| |
| /* Only do anything if we're changing state */ |
| if (enable != rfi_flush) |
| rfi_flush_enable(enable); |
| |
| return 0; |
| } |
| |
| static int rfi_flush_get(void *data, u64 *val) |
| { |
| *val = rfi_flush ? 1 : 0; |
| return 0; |
| } |
| |
| DEFINE_SIMPLE_ATTRIBUTE(fops_rfi_flush, rfi_flush_get, rfi_flush_set, "%llu\n"); |
| |
| static int entry_flush_set(void *data, u64 val) |
| { |
| bool enable; |
| |
| if (val == 1) |
| enable = true; |
| else if (val == 0) |
| enable = false; |
| else |
| return -EINVAL; |
| |
| /* Only do anything if we're changing state */ |
| if (enable != entry_flush) |
| entry_flush_enable(enable); |
| |
| return 0; |
| } |
| |
| static int entry_flush_get(void *data, u64 *val) |
| { |
| *val = entry_flush ? 1 : 0; |
| return 0; |
| } |
| |
| DEFINE_SIMPLE_ATTRIBUTE(fops_entry_flush, entry_flush_get, entry_flush_set, "%llu\n"); |
| |
| static int uaccess_flush_set(void *data, u64 val) |
| { |
| bool enable; |
| |
| if (val == 1) |
| enable = true; |
| else if (val == 0) |
| enable = false; |
| else |
| return -EINVAL; |
| |
| /* Only do anything if we're changing state */ |
| if (enable != uaccess_flush) |
| uaccess_flush_enable(enable); |
| |
| return 0; |
| } |
| |
| static int uaccess_flush_get(void *data, u64 *val) |
| { |
| *val = uaccess_flush ? 1 : 0; |
| return 0; |
| } |
| |
| DEFINE_SIMPLE_ATTRIBUTE(fops_uaccess_flush, uaccess_flush_get, uaccess_flush_set, "%llu\n"); |
| |
| static __init int rfi_flush_debugfs_init(void) |
| { |
| debugfs_create_file("rfi_flush", 0600, arch_debugfs_dir, NULL, &fops_rfi_flush); |
| debugfs_create_file("entry_flush", 0600, arch_debugfs_dir, NULL, &fops_entry_flush); |
| debugfs_create_file("uaccess_flush", 0600, arch_debugfs_dir, NULL, &fops_uaccess_flush); |
| return 0; |
| } |
| device_initcall(rfi_flush_debugfs_init); |
| #endif /* CONFIG_DEBUG_FS */ |
| #endif /* CONFIG_PPC_BOOK3S_64 */ |