| // SPDX-License-Identifier: GPL-2.0-or-later |
| /* |
| * Support for a cx23416 mpeg encoder via cx2388x host port. |
| * "blackbird" reference design. |
| * |
| * (c) 2004 Jelle Foks <jelle@foks.us> |
| * (c) 2004 Gerd Knorr <kraxel@bytesex.org> |
| * |
| * (c) 2005-2006 Mauro Carvalho Chehab <mchehab@kernel.org> |
| * - video_ioctl2 conversion |
| * |
| * Includes parts from the ivtv driver <http://sourceforge.net/projects/ivtv/> |
| */ |
| |
| #include "cx88.h" |
| |
| #include <linux/module.h> |
| #include <linux/init.h> |
| #include <linux/slab.h> |
| #include <linux/fs.h> |
| #include <linux/delay.h> |
| #include <linux/device.h> |
| #include <linux/firmware.h> |
| #include <media/v4l2-common.h> |
| #include <media/v4l2-ioctl.h> |
| #include <media/v4l2-event.h> |
| #include <media/drv-intf/cx2341x.h> |
| |
| MODULE_DESCRIPTION("driver for cx2388x/cx23416 based mpeg encoder cards"); |
| MODULE_AUTHOR("Jelle Foks <jelle@foks.us>, Gerd Knorr <kraxel@bytesex.org> [SuSE Labs]"); |
| MODULE_LICENSE("GPL v2"); |
| MODULE_VERSION(CX88_VERSION); |
| |
| static unsigned int debug; |
| module_param(debug, int, 0644); |
| MODULE_PARM_DESC(debug, "enable debug messages [blackbird]"); |
| |
| #define dprintk(level, fmt, arg...) do { \ |
| if (debug + 1 > level) \ |
| printk(KERN_DEBUG pr_fmt("%s: blackbird:" fmt), \ |
| __func__, ##arg); \ |
| } while (0) |
| |
| /* ------------------------------------------------------------------ */ |
| |
| #define BLACKBIRD_FIRM_IMAGE_SIZE 376836 |
| |
| /* defines below are from ivtv-driver.h */ |
| |
| #define IVTV_CMD_HW_BLOCKS_RST 0xFFFFFFFF |
| |
| /* Firmware API commands */ |
| #define IVTV_API_STD_TIMEOUT 500 |
| |
| enum blackbird_capture_type { |
| BLACKBIRD_MPEG_CAPTURE, |
| BLACKBIRD_RAW_CAPTURE, |
| BLACKBIRD_RAW_PASSTHRU_CAPTURE |
| }; |
| |
| enum blackbird_capture_bits { |
| BLACKBIRD_RAW_BITS_NONE = 0x00, |
| BLACKBIRD_RAW_BITS_YUV_CAPTURE = 0x01, |
| BLACKBIRD_RAW_BITS_PCM_CAPTURE = 0x02, |
| BLACKBIRD_RAW_BITS_VBI_CAPTURE = 0x04, |
| BLACKBIRD_RAW_BITS_PASSTHRU_CAPTURE = 0x08, |
| BLACKBIRD_RAW_BITS_TO_HOST_CAPTURE = 0x10 |
| }; |
| |
| enum blackbird_capture_end { |
| BLACKBIRD_END_AT_GOP, /* stop at the end of gop, generate irq */ |
| BLACKBIRD_END_NOW, /* stop immediately, no irq */ |
| }; |
| |
| enum blackbird_framerate { |
| BLACKBIRD_FRAMERATE_NTSC_30, /* NTSC: 30fps */ |
| BLACKBIRD_FRAMERATE_PAL_25 /* PAL: 25fps */ |
| }; |
| |
| enum blackbird_stream_port { |
| BLACKBIRD_OUTPUT_PORT_MEMORY, |
| BLACKBIRD_OUTPUT_PORT_STREAMING, |
| BLACKBIRD_OUTPUT_PORT_SERIAL |
| }; |
| |
| enum blackbird_data_xfer_status { |
| BLACKBIRD_MORE_BUFFERS_FOLLOW, |
| BLACKBIRD_LAST_BUFFER, |
| }; |
| |
| enum blackbird_picture_mask { |
| BLACKBIRD_PICTURE_MASK_NONE, |
| BLACKBIRD_PICTURE_MASK_I_FRAMES, |
| BLACKBIRD_PICTURE_MASK_I_P_FRAMES = 0x3, |
| BLACKBIRD_PICTURE_MASK_ALL_FRAMES = 0x7, |
| }; |
| |
| enum blackbird_vbi_mode_bits { |
| BLACKBIRD_VBI_BITS_SLICED, |
| BLACKBIRD_VBI_BITS_RAW, |
| }; |
| |
| enum blackbird_vbi_insertion_bits { |
| BLACKBIRD_VBI_BITS_INSERT_IN_XTENSION_USR_DATA, |
| BLACKBIRD_VBI_BITS_INSERT_IN_PRIVATE_PACKETS = 0x1 << 1, |
| BLACKBIRD_VBI_BITS_SEPARATE_STREAM = 0x2 << 1, |
| BLACKBIRD_VBI_BITS_SEPARATE_STREAM_USR_DATA = 0x4 << 1, |
| BLACKBIRD_VBI_BITS_SEPARATE_STREAM_PRV_DATA = 0x5 << 1, |
| }; |
| |
| enum blackbird_dma_unit { |
| BLACKBIRD_DMA_BYTES, |
| BLACKBIRD_DMA_FRAMES, |
| }; |
| |
| enum blackbird_dma_transfer_status_bits { |
| BLACKBIRD_DMA_TRANSFER_BITS_DONE = 0x01, |
| BLACKBIRD_DMA_TRANSFER_BITS_ERROR = 0x04, |
| BLACKBIRD_DMA_TRANSFER_BITS_LL_ERROR = 0x10, |
| }; |
| |
| enum blackbird_pause { |
| BLACKBIRD_PAUSE_ENCODING, |
| BLACKBIRD_RESUME_ENCODING, |
| }; |
| |
| enum blackbird_copyright { |
| BLACKBIRD_COPYRIGHT_OFF, |
| BLACKBIRD_COPYRIGHT_ON, |
| }; |
| |
| enum blackbird_notification_type { |
| BLACKBIRD_NOTIFICATION_REFRESH, |
| }; |
| |
| enum blackbird_notification_status { |
| BLACKBIRD_NOTIFICATION_OFF, |
| BLACKBIRD_NOTIFICATION_ON, |
| }; |
| |
| enum blackbird_notification_mailbox { |
| BLACKBIRD_NOTIFICATION_NO_MAILBOX = -1, |
| }; |
| |
| enum blackbird_field1_lines { |
| BLACKBIRD_FIELD1_SAA7114 = 0x00EF, /* 239 */ |
| BLACKBIRD_FIELD1_SAA7115 = 0x00F0, /* 240 */ |
| BLACKBIRD_FIELD1_MICRONAS = 0x0105, /* 261 */ |
| }; |
| |
| enum blackbird_field2_lines { |
| BLACKBIRD_FIELD2_SAA7114 = 0x00EF, /* 239 */ |
| BLACKBIRD_FIELD2_SAA7115 = 0x00F0, /* 240 */ |
| BLACKBIRD_FIELD2_MICRONAS = 0x0106, /* 262 */ |
| }; |
| |
| enum blackbird_custom_data_type { |
| BLACKBIRD_CUSTOM_EXTENSION_USR_DATA, |
| BLACKBIRD_CUSTOM_PRIVATE_PACKET, |
| }; |
| |
| enum blackbird_mute { |
| BLACKBIRD_UNMUTE, |
| BLACKBIRD_MUTE, |
| }; |
| |
| enum blackbird_mute_video_mask { |
| BLACKBIRD_MUTE_VIDEO_V_MASK = 0x0000FF00, |
| BLACKBIRD_MUTE_VIDEO_U_MASK = 0x00FF0000, |
| BLACKBIRD_MUTE_VIDEO_Y_MASK = 0xFF000000, |
| }; |
| |
| enum blackbird_mute_video_shift { |
| BLACKBIRD_MUTE_VIDEO_V_SHIFT = 8, |
| BLACKBIRD_MUTE_VIDEO_U_SHIFT = 16, |
| BLACKBIRD_MUTE_VIDEO_Y_SHIFT = 24, |
| }; |
| |
| /* Registers */ |
| #define IVTV_REG_ENC_SDRAM_REFRESH (0x07F8 /*| IVTV_REG_OFFSET*/) |
| #define IVTV_REG_ENC_SDRAM_PRECHARGE (0x07FC /*| IVTV_REG_OFFSET*/) |
| #define IVTV_REG_SPU (0x9050 /*| IVTV_REG_OFFSET*/) |
| #define IVTV_REG_HW_BLOCKS (0x9054 /*| IVTV_REG_OFFSET*/) |
| #define IVTV_REG_VPU (0x9058 /*| IVTV_REG_OFFSET*/) |
| #define IVTV_REG_APU (0xA064 /*| IVTV_REG_OFFSET*/) |
| |
| /* ------------------------------------------------------------------ */ |
| |
| static void host_setup(struct cx88_core *core) |
| { |
| /* toggle reset of the host */ |
| cx_write(MO_GPHST_SOFT_RST, 1); |
| udelay(100); |
| cx_write(MO_GPHST_SOFT_RST, 0); |
| udelay(100); |
| |
| /* host port setup */ |
| cx_write(MO_GPHST_WSC, 0x44444444U); |
| cx_write(MO_GPHST_XFR, 0); |
| cx_write(MO_GPHST_WDTH, 15); |
| cx_write(MO_GPHST_HDSHK, 0); |
| cx_write(MO_GPHST_MUX16, 0x44448888U); |
| cx_write(MO_GPHST_MODE, 0); |
| } |
| |
| /* ------------------------------------------------------------------ */ |
| |
| #define P1_MDATA0 0x390000 |
| #define P1_MDATA1 0x390001 |
| #define P1_MDATA2 0x390002 |
| #define P1_MDATA3 0x390003 |
| #define P1_MADDR2 0x390004 |
| #define P1_MADDR1 0x390005 |
| #define P1_MADDR0 0x390006 |
| #define P1_RDATA0 0x390008 |
| #define P1_RDATA1 0x390009 |
| #define P1_RDATA2 0x39000A |
| #define P1_RDATA3 0x39000B |
| #define P1_RADDR0 0x39000C |
| #define P1_RADDR1 0x39000D |
| #define P1_RRDWR 0x39000E |
| |
| static int wait_ready_gpio0_bit1(struct cx88_core *core, u32 state) |
| { |
| unsigned long timeout = jiffies + msecs_to_jiffies(1); |
| u32 gpio0, need; |
| |
| need = state ? 2 : 0; |
| for (;;) { |
| gpio0 = cx_read(MO_GP0_IO) & 2; |
| if (need == gpio0) |
| return 0; |
| if (time_after(jiffies, timeout)) |
| return -1; |
| udelay(1); |
| } |
| } |
| |
| static int memory_write(struct cx88_core *core, u32 address, u32 value) |
| { |
| /* Warning: address is dword address (4 bytes) */ |
| cx_writeb(P1_MDATA0, (unsigned int)value); |
| cx_writeb(P1_MDATA1, (unsigned int)(value >> 8)); |
| cx_writeb(P1_MDATA2, (unsigned int)(value >> 16)); |
| cx_writeb(P1_MDATA3, (unsigned int)(value >> 24)); |
| cx_writeb(P1_MADDR2, (unsigned int)(address >> 16) | 0x40); |
| cx_writeb(P1_MADDR1, (unsigned int)(address >> 8)); |
| cx_writeb(P1_MADDR0, (unsigned int)address); |
| cx_read(P1_MDATA0); |
| cx_read(P1_MADDR0); |
| |
| return wait_ready_gpio0_bit1(core, 1); |
| } |
| |
| static int memory_read(struct cx88_core *core, u32 address, u32 *value) |
| { |
| int retval; |
| u32 val; |
| |
| /* Warning: address is dword address (4 bytes) */ |
| cx_writeb(P1_MADDR2, (unsigned int)(address >> 16) & ~0xC0); |
| cx_writeb(P1_MADDR1, (unsigned int)(address >> 8)); |
| cx_writeb(P1_MADDR0, (unsigned int)address); |
| cx_read(P1_MADDR0); |
| |
| retval = wait_ready_gpio0_bit1(core, 1); |
| |
| cx_writeb(P1_MDATA3, 0); |
| val = (unsigned char)cx_read(P1_MDATA3) << 24; |
| cx_writeb(P1_MDATA2, 0); |
| val |= (unsigned char)cx_read(P1_MDATA2) << 16; |
| cx_writeb(P1_MDATA1, 0); |
| val |= (unsigned char)cx_read(P1_MDATA1) << 8; |
| cx_writeb(P1_MDATA0, 0); |
| val |= (unsigned char)cx_read(P1_MDATA0); |
| |
| *value = val; |
| return retval; |
| } |
| |
| static int register_write(struct cx88_core *core, u32 address, u32 value) |
| { |
| cx_writeb(P1_RDATA0, (unsigned int)value); |
| cx_writeb(P1_RDATA1, (unsigned int)(value >> 8)); |
| cx_writeb(P1_RDATA2, (unsigned int)(value >> 16)); |
| cx_writeb(P1_RDATA3, (unsigned int)(value >> 24)); |
| cx_writeb(P1_RADDR0, (unsigned int)address); |
| cx_writeb(P1_RADDR1, (unsigned int)(address >> 8)); |
| cx_writeb(P1_RRDWR, 1); |
| cx_read(P1_RDATA0); |
| cx_read(P1_RADDR0); |
| |
| return wait_ready_gpio0_bit1(core, 1); |
| } |
| |
| static int register_read(struct cx88_core *core, u32 address, u32 *value) |
| { |
| int retval; |
| u32 val; |
| |
| cx_writeb(P1_RADDR0, (unsigned int)address); |
| cx_writeb(P1_RADDR1, (unsigned int)(address >> 8)); |
| cx_writeb(P1_RRDWR, 0); |
| cx_read(P1_RADDR0); |
| |
| retval = wait_ready_gpio0_bit1(core, 1); |
| val = (unsigned char)cx_read(P1_RDATA0); |
| val |= (unsigned char)cx_read(P1_RDATA1) << 8; |
| val |= (unsigned char)cx_read(P1_RDATA2) << 16; |
| val |= (unsigned char)cx_read(P1_RDATA3) << 24; |
| |
| *value = val; |
| return retval; |
| } |
| |
| /* ------------------------------------------------------------------ */ |
| |
| static int blackbird_mbox_func(void *priv, u32 command, int in, |
| int out, u32 data[CX2341X_MBOX_MAX_DATA]) |
| { |
| struct cx8802_dev *dev = priv; |
| unsigned long timeout; |
| u32 value, flag, retval; |
| int i; |
| |
| dprintk(1, "%s: 0x%X\n", __func__, command); |
| |
| /* |
| * this may not be 100% safe if we can't read any memory location |
| * without side effects |
| */ |
| memory_read(dev->core, dev->mailbox - 4, &value); |
| if (value != 0x12345678) { |
| dprintk(0, |
| "Firmware and/or mailbox pointer not initialized or corrupted\n"); |
| return -EIO; |
| } |
| |
| memory_read(dev->core, dev->mailbox, &flag); |
| if (flag) { |
| dprintk(0, "ERROR: Mailbox appears to be in use (%x)\n", flag); |
| return -EIO; |
| } |
| |
| flag |= 1; /* tell 'em we're working on it */ |
| memory_write(dev->core, dev->mailbox, flag); |
| |
| /* write command + args + fill remaining with zeros */ |
| memory_write(dev->core, dev->mailbox + 1, command); /* command code */ |
| /* timeout */ |
| memory_write(dev->core, dev->mailbox + 3, IVTV_API_STD_TIMEOUT); |
| for (i = 0; i < in; i++) { |
| memory_write(dev->core, dev->mailbox + 4 + i, data[i]); |
| dprintk(1, "API Input %d = %d\n", i, data[i]); |
| } |
| for (; i < CX2341X_MBOX_MAX_DATA; i++) |
| memory_write(dev->core, dev->mailbox + 4 + i, 0); |
| |
| flag |= 3; /* tell 'em we're done writing */ |
| memory_write(dev->core, dev->mailbox, flag); |
| |
| /* wait for firmware to handle the API command */ |
| timeout = jiffies + msecs_to_jiffies(1000); |
| for (;;) { |
| memory_read(dev->core, dev->mailbox, &flag); |
| if (0 != (flag & 4)) |
| break; |
| if (time_after(jiffies, timeout)) { |
| dprintk(0, "ERROR: API Mailbox timeout %x\n", command); |
| return -EIO; |
| } |
| udelay(10); |
| } |
| |
| /* read output values */ |
| for (i = 0; i < out; i++) { |
| memory_read(dev->core, dev->mailbox + 4 + i, data + i); |
| dprintk(1, "API Output %d = %d\n", i, data[i]); |
| } |
| |
| memory_read(dev->core, dev->mailbox + 2, &retval); |
| dprintk(1, "API result = %d\n", retval); |
| |
| flag = 0; |
| memory_write(dev->core, dev->mailbox, flag); |
| return retval; |
| } |
| |
| /* ------------------------------------------------------------------ */ |
| |
| /* |
| * We don't need to call the API often, so using just one mailbox |
| * will probably suffice |
| */ |
| static int blackbird_api_cmd(struct cx8802_dev *dev, u32 command, |
| u32 inputcnt, u32 outputcnt, ...) |
| { |
| u32 data[CX2341X_MBOX_MAX_DATA]; |
| va_list vargs; |
| int i, err; |
| |
| va_start(vargs, outputcnt); |
| |
| for (i = 0; i < inputcnt; i++) |
| data[i] = va_arg(vargs, int); |
| |
| err = blackbird_mbox_func(dev, command, inputcnt, outputcnt, data); |
| for (i = 0; i < outputcnt; i++) { |
| int *vptr = va_arg(vargs, int *); |
| *vptr = data[i]; |
| } |
| va_end(vargs); |
| return err; |
| } |
| |
| static int blackbird_find_mailbox(struct cx8802_dev *dev) |
| { |
| u32 signature[4] = {0x12345678, 0x34567812, 0x56781234, 0x78123456}; |
| int signaturecnt = 0; |
| u32 value; |
| int i; |
| |
| for (i = 0; i < BLACKBIRD_FIRM_IMAGE_SIZE; i++) { |
| memory_read(dev->core, i, &value); |
| if (value == signature[signaturecnt]) |
| signaturecnt++; |
| else |
| signaturecnt = 0; |
| if (signaturecnt == 4) { |
| dprintk(1, "Mailbox signature found\n"); |
| return i + 1; |
| } |
| } |
| dprintk(0, "Mailbox signature values not found!\n"); |
| return -EIO; |
| } |
| |
| static int blackbird_load_firmware(struct cx8802_dev *dev) |
| { |
| static const unsigned char magic[8] = { |
| 0xa7, 0x0d, 0x00, 0x00, 0x66, 0xbb, 0x55, 0xaa |
| }; |
| const struct firmware *firmware; |
| int i, retval = 0; |
| u32 value = 0; |
| u32 checksum = 0; |
| __le32 *dataptr; |
| |
| retval = register_write(dev->core, IVTV_REG_VPU, 0xFFFFFFED); |
| retval |= register_write(dev->core, IVTV_REG_HW_BLOCKS, |
| IVTV_CMD_HW_BLOCKS_RST); |
| retval |= register_write(dev->core, IVTV_REG_ENC_SDRAM_REFRESH, |
| 0x80000640); |
| retval |= register_write(dev->core, IVTV_REG_ENC_SDRAM_PRECHARGE, |
| 0x1A); |
| usleep_range(10000, 20000); |
| retval |= register_write(dev->core, IVTV_REG_APU, 0); |
| |
| if (retval < 0) |
| dprintk(0, "Error with register_write\n"); |
| |
| retval = request_firmware(&firmware, CX2341X_FIRM_ENC_FILENAME, |
| &dev->pci->dev); |
| |
| if (retval != 0) { |
| pr_err("Hotplug firmware request failed (%s).\n", |
| CX2341X_FIRM_ENC_FILENAME); |
| pr_err("Please fix your hotplug setup, the board will not work without firmware loaded!\n"); |
| return -EIO; |
| } |
| |
| if (firmware->size != BLACKBIRD_FIRM_IMAGE_SIZE) { |
| pr_err("Firmware size mismatch (have %zd, expected %d)\n", |
| firmware->size, BLACKBIRD_FIRM_IMAGE_SIZE); |
| release_firmware(firmware); |
| return -EINVAL; |
| } |
| |
| if (memcmp(firmware->data, magic, 8) != 0) { |
| pr_err("Firmware magic mismatch, wrong file?\n"); |
| release_firmware(firmware); |
| return -EINVAL; |
| } |
| |
| /* transfer to the chip */ |
| dprintk(1, "Loading firmware ...\n"); |
| dataptr = (__le32 *)firmware->data; |
| for (i = 0; i < (firmware->size >> 2); i++) { |
| value = le32_to_cpu(*dataptr); |
| checksum += ~value; |
| memory_write(dev->core, i, value); |
| dataptr++; |
| } |
| |
| /* read back to verify with the checksum */ |
| for (i--; i >= 0; i--) { |
| memory_read(dev->core, i, &value); |
| checksum -= ~value; |
| } |
| release_firmware(firmware); |
| if (checksum) { |
| pr_err("Firmware load might have failed (checksum mismatch).\n"); |
| return -EIO; |
| } |
| dprintk(0, "Firmware upload successful.\n"); |
| |
| retval |= register_write(dev->core, IVTV_REG_HW_BLOCKS, |
| IVTV_CMD_HW_BLOCKS_RST); |
| retval |= register_read(dev->core, IVTV_REG_SPU, &value); |
| retval |= register_write(dev->core, IVTV_REG_SPU, value & 0xFFFFFFFE); |
| usleep_range(10000, 20000); |
| |
| retval |= register_read(dev->core, IVTV_REG_VPU, &value); |
| retval |= register_write(dev->core, IVTV_REG_VPU, value & 0xFFFFFFE8); |
| |
| if (retval < 0) |
| dprintk(0, "Error with register_write\n"); |
| return 0; |
| } |
| |
| /* |
| * Settings used by the windows tv app for PVR2000: |
| * ================================================================================================================= |
| * Profile | Codec | Resolution | CBR/VBR | Video Qlty | V. Bitrate | Frmrate | Audio Codec | A. Bitrate | A. Mode |
| * ----------------------------------------------------------------------------------------------------------------- |
| * MPEG-1 | MPEG1 | 352x288PAL | (CBR) | 1000:Optimal | 2000 Kbps | 25fps | MPG1 Layer2 | 224kbps | Stereo |
| * MPEG-2 | MPEG2 | 720x576PAL | VBR | 600 :Good | 4000 Kbps | 25fps | MPG1 Layer2 | 224kbps | Stereo |
| * VCD | MPEG1 | 352x288PAL | (CBR) | 1000:Optimal | 1150 Kbps | 25fps | MPG1 Layer2 | 224kbps | Stereo |
| * DVD | MPEG2 | 720x576PAL | VBR | 600 :Good | 6000 Kbps | 25fps | MPG1 Layer2 | 224kbps | Stereo |
| * DB* DVD | MPEG2 | 720x576PAL | CBR | 600 :Good | 6000 Kbps | 25fps | MPG1 Layer2 | 224kbps | Stereo |
| * ================================================================================================================= |
| * [*] DB: "DirectBurn" |
| */ |
| |
| static void blackbird_codec_settings(struct cx8802_dev *dev) |
| { |
| struct cx88_core *core = dev->core; |
| |
| /* assign frame size */ |
| blackbird_api_cmd(dev, CX2341X_ENC_SET_FRAME_SIZE, 2, 0, |
| core->height, core->width); |
| |
| dev->cxhdl.width = core->width; |
| dev->cxhdl.height = core->height; |
| cx2341x_handler_set_50hz(&dev->cxhdl, |
| dev->core->tvnorm & V4L2_STD_625_50); |
| cx2341x_handler_setup(&dev->cxhdl); |
| } |
| |
| static int blackbird_initialize_codec(struct cx8802_dev *dev) |
| { |
| struct cx88_core *core = dev->core; |
| int version; |
| int retval; |
| |
| dprintk(1, "Initialize codec\n"); |
| retval = blackbird_api_cmd(dev, CX2341X_ENC_PING_FW, 0, 0); /* ping */ |
| if (retval < 0) { |
| /* ping was not successful, reset and upload firmware */ |
| cx_write(MO_SRST_IO, 0); /* SYS_RSTO=0 */ |
| cx_write(MO_SRST_IO, 1); /* SYS_RSTO=1 */ |
| retval = blackbird_load_firmware(dev); |
| if (retval < 0) |
| return retval; |
| |
| retval = blackbird_find_mailbox(dev); |
| if (retval < 0) |
| return -1; |
| |
| dev->mailbox = retval; |
| |
| /* ping */ |
| retval = blackbird_api_cmd(dev, CX2341X_ENC_PING_FW, 0, 0); |
| if (retval < 0) { |
| dprintk(0, "ERROR: Firmware ping failed!\n"); |
| return -1; |
| } |
| |
| retval = blackbird_api_cmd(dev, CX2341X_ENC_GET_VERSION, |
| 0, 1, &version); |
| if (retval < 0) { |
| dprintk(0, |
| "ERROR: Firmware get encoder version failed!\n"); |
| return -1; |
| } |
| dprintk(0, "Firmware version is 0x%08x\n", version); |
| } |
| |
| cx_write(MO_PINMUX_IO, 0x88); /* 656-8bit IO and enable MPEG parallel IO */ |
| cx_clear(MO_INPUT_FORMAT, 0x100); /* chroma subcarrier lock to normal? */ |
| cx_write(MO_VBOS_CONTROL, 0x84A00); /* no 656 mode, 8-bit pixels, disable VBI */ |
| cx_clear(MO_OUTPUT_FORMAT, 0x0008); /* Normal Y-limits to let the mpeg encoder sync */ |
| |
| blackbird_codec_settings(dev); |
| |
| blackbird_api_cmd(dev, CX2341X_ENC_SET_NUM_VSYNC_LINES, 2, 0, |
| BLACKBIRD_FIELD1_SAA7115, BLACKBIRD_FIELD2_SAA7115); |
| |
| blackbird_api_cmd(dev, CX2341X_ENC_SET_PLACEHOLDER, 12, 0, |
| BLACKBIRD_CUSTOM_EXTENSION_USR_DATA, |
| 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0); |
| |
| return 0; |
| } |
| |
| static int blackbird_start_codec(struct cx8802_dev *dev) |
| { |
| struct cx88_core *core = dev->core; |
| /* start capturing to the host interface */ |
| u32 reg; |
| |
| int i; |
| int lastchange = -1; |
| int lastval = 0; |
| |
| for (i = 0; (i < 10) && (i < (lastchange + 4)); i++) { |
| reg = cx_read(AUD_STATUS); |
| |
| dprintk(1, "AUD_STATUS:%dL: 0x%x\n", i, reg); |
| if ((reg & 0x0F) != lastval) { |
| lastval = reg & 0x0F; |
| lastchange = i; |
| } |
| msleep(100); |
| } |
| |
| /* unmute audio source */ |
| cx_clear(AUD_VOL_CTL, (1 << 6)); |
| |
| blackbird_api_cmd(dev, CX2341X_ENC_REFRESH_INPUT, 0, 0); |
| |
| /* initialize the video input */ |
| blackbird_api_cmd(dev, CX2341X_ENC_INITIALIZE_INPUT, 0, 0); |
| |
| cx2341x_handler_set_busy(&dev->cxhdl, 1); |
| |
| /* start capturing to the host interface */ |
| blackbird_api_cmd(dev, CX2341X_ENC_START_CAPTURE, 2, 0, |
| BLACKBIRD_MPEG_CAPTURE, BLACKBIRD_RAW_BITS_NONE); |
| |
| return 0; |
| } |
| |
| static int blackbird_stop_codec(struct cx8802_dev *dev) |
| { |
| blackbird_api_cmd(dev, CX2341X_ENC_STOP_CAPTURE, 3, 0, |
| BLACKBIRD_END_NOW, |
| BLACKBIRD_MPEG_CAPTURE, |
| BLACKBIRD_RAW_BITS_NONE); |
| |
| cx2341x_handler_set_busy(&dev->cxhdl, 0); |
| |
| return 0; |
| } |
| |
| /* ------------------------------------------------------------------ */ |
| |
| static int queue_setup(struct vb2_queue *q, |
| unsigned int *num_buffers, unsigned int *num_planes, |
| unsigned int sizes[], struct device *alloc_devs[]) |
| { |
| struct cx8802_dev *dev = q->drv_priv; |
| |
| *num_planes = 1; |
| dev->ts_packet_size = 188 * 4; |
| dev->ts_packet_count = 32; |
| sizes[0] = dev->ts_packet_size * dev->ts_packet_count; |
| return 0; |
| } |
| |
| static int buffer_prepare(struct vb2_buffer *vb) |
| { |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct cx8802_dev *dev = vb->vb2_queue->drv_priv; |
| struct cx88_buffer *buf = container_of(vbuf, struct cx88_buffer, vb); |
| |
| return cx8802_buf_prepare(vb->vb2_queue, dev, buf); |
| } |
| |
| static void buffer_finish(struct vb2_buffer *vb) |
| { |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct cx8802_dev *dev = vb->vb2_queue->drv_priv; |
| struct cx88_buffer *buf = container_of(vbuf, struct cx88_buffer, vb); |
| struct cx88_riscmem *risc = &buf->risc; |
| |
| if (risc->cpu) |
| dma_free_coherent(&dev->pci->dev, risc->size, risc->cpu, |
| risc->dma); |
| memset(risc, 0, sizeof(*risc)); |
| } |
| |
| static void buffer_queue(struct vb2_buffer *vb) |
| { |
| struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb); |
| struct cx8802_dev *dev = vb->vb2_queue->drv_priv; |
| struct cx88_buffer *buf = container_of(vbuf, struct cx88_buffer, vb); |
| |
| cx8802_buf_queue(dev, buf); |
| } |
| |
| static int start_streaming(struct vb2_queue *q, unsigned int count) |
| { |
| struct cx8802_dev *dev = q->drv_priv; |
| struct cx88_dmaqueue *dmaq = &dev->mpegq; |
| struct cx8802_driver *drv; |
| struct cx88_buffer *buf; |
| unsigned long flags; |
| int err; |
| |
| /* Make sure we can acquire the hardware */ |
| drv = cx8802_get_driver(dev, CX88_MPEG_BLACKBIRD); |
| if (!drv) { |
| dprintk(1, "%s: blackbird driver is not loaded\n", __func__); |
| err = -ENODEV; |
| goto fail; |
| } |
| |
| err = drv->request_acquire(drv); |
| if (err != 0) { |
| dprintk(1, "%s: Unable to acquire hardware, %d\n", __func__, |
| err); |
| goto fail; |
| } |
| |
| if (blackbird_initialize_codec(dev) < 0) { |
| drv->request_release(drv); |
| err = -EINVAL; |
| goto fail; |
| } |
| |
| err = blackbird_start_codec(dev); |
| if (err == 0) { |
| buf = list_entry(dmaq->active.next, struct cx88_buffer, list); |
| cx8802_start_dma(dev, dmaq, buf); |
| return 0; |
| } |
| |
| fail: |
| spin_lock_irqsave(&dev->slock, flags); |
| while (!list_empty(&dmaq->active)) { |
| struct cx88_buffer *buf = list_entry(dmaq->active.next, |
| struct cx88_buffer, list); |
| |
| list_del(&buf->list); |
| vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_QUEUED); |
| } |
| spin_unlock_irqrestore(&dev->slock, flags); |
| return err; |
| } |
| |
| static void stop_streaming(struct vb2_queue *q) |
| { |
| struct cx8802_dev *dev = q->drv_priv; |
| struct cx88_dmaqueue *dmaq = &dev->mpegq; |
| struct cx8802_driver *drv = NULL; |
| unsigned long flags; |
| |
| cx8802_cancel_buffers(dev); |
| blackbird_stop_codec(dev); |
| |
| /* Make sure we release the hardware */ |
| drv = cx8802_get_driver(dev, CX88_MPEG_BLACKBIRD); |
| WARN_ON(!drv); |
| if (drv) |
| drv->request_release(drv); |
| |
| spin_lock_irqsave(&dev->slock, flags); |
| while (!list_empty(&dmaq->active)) { |
| struct cx88_buffer *buf = list_entry(dmaq->active.next, |
| struct cx88_buffer, list); |
| |
| list_del(&buf->list); |
| vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR); |
| } |
| spin_unlock_irqrestore(&dev->slock, flags); |
| } |
| |
| static const struct vb2_ops blackbird_qops = { |
| .queue_setup = queue_setup, |
| .buf_prepare = buffer_prepare, |
| .buf_finish = buffer_finish, |
| .buf_queue = buffer_queue, |
| .wait_prepare = vb2_ops_wait_prepare, |
| .wait_finish = vb2_ops_wait_finish, |
| .start_streaming = start_streaming, |
| .stop_streaming = stop_streaming, |
| }; |
| |
| /* ------------------------------------------------------------------ */ |
| |
| static int vidioc_querycap(struct file *file, void *priv, |
| struct v4l2_capability *cap) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| strscpy(cap->driver, "cx88_blackbird", sizeof(cap->driver)); |
| sprintf(cap->bus_info, "PCI:%s", pci_name(dev->pci)); |
| return cx88_querycap(file, core, cap); |
| } |
| |
| static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_fmtdesc *f) |
| { |
| if (f->index != 0) |
| return -EINVAL; |
| |
| f->pixelformat = V4L2_PIX_FMT_MPEG; |
| return 0; |
| } |
| |
| static int vidioc_g_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *f) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| f->fmt.pix.pixelformat = V4L2_PIX_FMT_MPEG; |
| f->fmt.pix.bytesperline = 0; |
| f->fmt.pix.sizeimage = dev->ts_packet_size * dev->ts_packet_count; |
| f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; |
| f->fmt.pix.width = core->width; |
| f->fmt.pix.height = core->height; |
| f->fmt.pix.field = core->field; |
| return 0; |
| } |
| |
| static int vidioc_try_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *f) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| unsigned int maxw, maxh; |
| enum v4l2_field field; |
| |
| f->fmt.pix.pixelformat = V4L2_PIX_FMT_MPEG; |
| f->fmt.pix.bytesperline = 0; |
| f->fmt.pix.sizeimage = dev->ts_packet_size * dev->ts_packet_count; |
| f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; |
| |
| maxw = norm_maxw(core->tvnorm); |
| maxh = norm_maxh(core->tvnorm); |
| |
| field = f->fmt.pix.field; |
| |
| switch (field) { |
| case V4L2_FIELD_TOP: |
| case V4L2_FIELD_BOTTOM: |
| case V4L2_FIELD_INTERLACED: |
| case V4L2_FIELD_SEQ_BT: |
| case V4L2_FIELD_SEQ_TB: |
| break; |
| default: |
| field = (f->fmt.pix.height > maxh / 2) |
| ? V4L2_FIELD_INTERLACED |
| : V4L2_FIELD_BOTTOM; |
| break; |
| } |
| if (V4L2_FIELD_HAS_T_OR_B(field)) |
| maxh /= 2; |
| |
| v4l_bound_align_image(&f->fmt.pix.width, 48, maxw, 2, |
| &f->fmt.pix.height, 32, maxh, 0, 0); |
| f->fmt.pix.field = field; |
| return 0; |
| } |
| |
| static int vidioc_s_fmt_vid_cap(struct file *file, void *priv, |
| struct v4l2_format *f) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| if (vb2_is_busy(&dev->vb2_mpegq)) |
| return -EBUSY; |
| if (core->v4ldev && (vb2_is_busy(&core->v4ldev->vb2_vidq) || |
| vb2_is_busy(&core->v4ldev->vb2_vbiq))) |
| return -EBUSY; |
| vidioc_try_fmt_vid_cap(file, priv, f); |
| core->width = f->fmt.pix.width; |
| core->height = f->fmt.pix.height; |
| core->field = f->fmt.pix.field; |
| cx88_set_scale(core, f->fmt.pix.width, f->fmt.pix.height, |
| f->fmt.pix.field); |
| blackbird_api_cmd(dev, CX2341X_ENC_SET_FRAME_SIZE, 2, 0, |
| f->fmt.pix.height, f->fmt.pix.width); |
| return 0; |
| } |
| |
| static int vidioc_s_frequency(struct file *file, void *priv, |
| const struct v4l2_frequency *f) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| bool streaming; |
| |
| if (unlikely(core->board.tuner_type == UNSET)) |
| return -EINVAL; |
| if (unlikely(f->tuner != 0)) |
| return -EINVAL; |
| streaming = vb2_start_streaming_called(&dev->vb2_mpegq); |
| if (streaming) |
| blackbird_stop_codec(dev); |
| |
| cx88_set_freq(core, f); |
| blackbird_initialize_codec(dev); |
| cx88_set_scale(core, core->width, core->height, core->field); |
| if (streaming) |
| blackbird_start_codec(dev); |
| return 0; |
| } |
| |
| static int vidioc_log_status(struct file *file, void *priv) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| char name[32 + 2]; |
| |
| snprintf(name, sizeof(name), "%s/2", core->name); |
| call_all(core, core, log_status); |
| v4l2_ctrl_handler_log_status(&dev->cxhdl.hdl, name); |
| return 0; |
| } |
| |
| static int vidioc_enum_input(struct file *file, void *priv, |
| struct v4l2_input *i) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| return cx88_enum_input(core, i); |
| } |
| |
| static int vidioc_g_frequency(struct file *file, void *priv, |
| struct v4l2_frequency *f) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| if (unlikely(core->board.tuner_type == UNSET)) |
| return -EINVAL; |
| if (unlikely(f->tuner != 0)) |
| return -EINVAL; |
| |
| f->frequency = core->freq; |
| call_all(core, tuner, g_frequency, f); |
| |
| return 0; |
| } |
| |
| static int vidioc_g_input(struct file *file, void *priv, unsigned int *i) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| *i = core->input; |
| return 0; |
| } |
| |
| static int vidioc_s_input(struct file *file, void *priv, unsigned int i) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| if (i >= 4) |
| return -EINVAL; |
| if (!INPUT(i).type) |
| return -EINVAL; |
| |
| cx88_newstation(core); |
| cx88_video_mux(core, i); |
| return 0; |
| } |
| |
| static int vidioc_g_tuner(struct file *file, void *priv, |
| struct v4l2_tuner *t) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| u32 reg; |
| |
| if (unlikely(core->board.tuner_type == UNSET)) |
| return -EINVAL; |
| if (t->index != 0) |
| return -EINVAL; |
| |
| strscpy(t->name, "Television", sizeof(t->name)); |
| t->capability = V4L2_TUNER_CAP_NORM; |
| t->rangehigh = 0xffffffffUL; |
| call_all(core, tuner, g_tuner, t); |
| |
| cx88_get_stereo(core, t); |
| reg = cx_read(MO_DEVICE_STATUS); |
| t->signal = (reg & (1 << 5)) ? 0xffff : 0x0000; |
| return 0; |
| } |
| |
| static int vidioc_s_tuner(struct file *file, void *priv, |
| const struct v4l2_tuner *t) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| if (core->board.tuner_type == UNSET) |
| return -EINVAL; |
| if (t->index != 0) |
| return -EINVAL; |
| |
| cx88_set_stereo(core, t->audmode, 1); |
| return 0; |
| } |
| |
| static int vidioc_g_std(struct file *file, void *priv, v4l2_std_id *tvnorm) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| *tvnorm = core->tvnorm; |
| return 0; |
| } |
| |
| static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id id) |
| { |
| struct cx8802_dev *dev = video_drvdata(file); |
| struct cx88_core *core = dev->core; |
| |
| return cx88_set_tvnorm(core, id); |
| } |
| |
| static const struct v4l2_file_operations mpeg_fops = { |
| .owner = THIS_MODULE, |
| .open = v4l2_fh_open, |
| .release = vb2_fop_release, |
| .read = vb2_fop_read, |
| .poll = vb2_fop_poll, |
| .mmap = vb2_fop_mmap, |
| .unlocked_ioctl = video_ioctl2, |
| }; |
| |
| static const struct v4l2_ioctl_ops mpeg_ioctl_ops = { |
| .vidioc_querycap = vidioc_querycap, |
| .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap, |
| .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap, |
| .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap, |
| .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap, |
| .vidioc_reqbufs = vb2_ioctl_reqbufs, |
| .vidioc_querybuf = vb2_ioctl_querybuf, |
| .vidioc_qbuf = vb2_ioctl_qbuf, |
| .vidioc_dqbuf = vb2_ioctl_dqbuf, |
| .vidioc_streamon = vb2_ioctl_streamon, |
| .vidioc_streamoff = vb2_ioctl_streamoff, |
| .vidioc_s_frequency = vidioc_s_frequency, |
| .vidioc_log_status = vidioc_log_status, |
| .vidioc_enum_input = vidioc_enum_input, |
| .vidioc_g_frequency = vidioc_g_frequency, |
| .vidioc_g_input = vidioc_g_input, |
| .vidioc_s_input = vidioc_s_input, |
| .vidioc_g_tuner = vidioc_g_tuner, |
| .vidioc_s_tuner = vidioc_s_tuner, |
| .vidioc_g_std = vidioc_g_std, |
| .vidioc_s_std = vidioc_s_std, |
| .vidioc_subscribe_event = v4l2_ctrl_subscribe_event, |
| .vidioc_unsubscribe_event = v4l2_event_unsubscribe, |
| }; |
| |
| static const struct video_device cx8802_mpeg_template = { |
| .name = "cx8802", |
| .fops = &mpeg_fops, |
| .ioctl_ops = &mpeg_ioctl_ops, |
| .tvnorms = CX88_NORMS, |
| }; |
| |
| /* ------------------------------------------------------------------ */ |
| |
| /* The CX8802 MPEG API will call this when we can use the hardware */ |
| static int cx8802_blackbird_advise_acquire(struct cx8802_driver *drv) |
| { |
| struct cx88_core *core = drv->core; |
| int err = 0; |
| |
| switch (core->boardnr) { |
| case CX88_BOARD_HAUPPAUGE_HVR1300: |
| /* |
| * By default, core setup will leave the cx22702 out of reset, |
| * on the bus. |
| * We left the hardware on power up with the cx22702 active. |
| * We're being given access to re-arrange the GPIOs. |
| * Take the bus off the cx22702 and put the cx23416 on it. |
| */ |
| /* Toggle reset on cx22702 leaving i2c active */ |
| cx_set(MO_GP0_IO, 0x00000080); |
| udelay(1000); |
| cx_clear(MO_GP0_IO, 0x00000080); |
| udelay(50); |
| cx_set(MO_GP0_IO, 0x00000080); |
| udelay(1000); |
| /* tri-state the cx22702 pins */ |
| cx_set(MO_GP0_IO, 0x00000004); |
| udelay(1000); |
| break; |
| default: |
| err = -ENODEV; |
| } |
| return err; |
| } |
| |
| /* The CX8802 MPEG API will call this when we need to release the hardware */ |
| static int cx8802_blackbird_advise_release(struct cx8802_driver *drv) |
| { |
| struct cx88_core *core = drv->core; |
| int err = 0; |
| |
| switch (core->boardnr) { |
| case CX88_BOARD_HAUPPAUGE_HVR1300: |
| /* Exit leaving the cx23416 on the bus */ |
| break; |
| default: |
| err = -ENODEV; |
| } |
| return err; |
| } |
| |
| static void blackbird_unregister_video(struct cx8802_dev *dev) |
| { |
| video_unregister_device(&dev->mpeg_dev); |
| } |
| |
| static int blackbird_register_video(struct cx8802_dev *dev) |
| { |
| int err; |
| |
| cx88_vdev_init(dev->core, dev->pci, &dev->mpeg_dev, |
| &cx8802_mpeg_template, "mpeg"); |
| dev->mpeg_dev.ctrl_handler = &dev->cxhdl.hdl; |
| video_set_drvdata(&dev->mpeg_dev, dev); |
| dev->mpeg_dev.queue = &dev->vb2_mpegq; |
| dev->mpeg_dev.device_caps = V4L2_CAP_READWRITE | V4L2_CAP_STREAMING | |
| V4L2_CAP_VIDEO_CAPTURE; |
| if (dev->core->board.tuner_type != UNSET) |
| dev->mpeg_dev.device_caps |= V4L2_CAP_TUNER; |
| err = video_register_device(&dev->mpeg_dev, VFL_TYPE_VIDEO, -1); |
| if (err < 0) { |
| pr_info("can't register mpeg device\n"); |
| return err; |
| } |
| pr_info("registered device %s [mpeg]\n", |
| video_device_node_name(&dev->mpeg_dev)); |
| return 0; |
| } |
| |
| /* ----------------------------------------------------------- */ |
| |
| static int cx8802_blackbird_probe(struct cx8802_driver *drv) |
| { |
| struct cx88_core *core = drv->core; |
| struct cx8802_dev *dev = core->dvbdev; |
| struct vb2_queue *q; |
| int err; |
| |
| dprintk(1, "%s\n", __func__); |
| dprintk(1, " ->being probed by Card=%d Name=%s, PCI %02x:%02x\n", |
| core->boardnr, |
| core->name, |
| core->pci_bus, |
| core->pci_slot); |
| |
| err = -ENODEV; |
| if (!(core->board.mpeg & CX88_MPEG_BLACKBIRD)) |
| goto fail_core; |
| |
| dev->cxhdl.port = CX2341X_PORT_STREAMING; |
| dev->cxhdl.width = core->width; |
| dev->cxhdl.height = core->height; |
| dev->cxhdl.func = blackbird_mbox_func; |
| dev->cxhdl.priv = dev; |
| err = cx2341x_handler_init(&dev->cxhdl, 36); |
| if (err) |
| goto fail_core; |
| v4l2_ctrl_add_handler(&dev->cxhdl.hdl, &core->video_hdl, NULL, false); |
| |
| /* blackbird stuff */ |
| pr_info("cx23416 based mpeg encoder (blackbird reference design)\n"); |
| host_setup(dev->core); |
| |
| blackbird_initialize_codec(dev); |
| |
| /* initial device configuration: needed ? */ |
| // init_controls(core); |
| cx88_set_tvnorm(core, core->tvnorm); |
| cx88_video_mux(core, 0); |
| cx2341x_handler_set_50hz(&dev->cxhdl, core->height == 576); |
| cx2341x_handler_setup(&dev->cxhdl); |
| |
| q = &dev->vb2_mpegq; |
| q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE; |
| q->io_modes = VB2_MMAP | VB2_USERPTR | VB2_DMABUF | VB2_READ; |
| q->gfp_flags = GFP_DMA32; |
| q->min_buffers_needed = 2; |
| q->drv_priv = dev; |
| q->buf_struct_size = sizeof(struct cx88_buffer); |
| q->ops = &blackbird_qops; |
| q->mem_ops = &vb2_dma_sg_memops; |
| q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC; |
| q->lock = &core->lock; |
| q->dev = &dev->pci->dev; |
| |
| err = vb2_queue_init(q); |
| if (err < 0) |
| goto fail_core; |
| |
| blackbird_register_video(dev); |
| |
| return 0; |
| |
| fail_core: |
| return err; |
| } |
| |
| static int cx8802_blackbird_remove(struct cx8802_driver *drv) |
| { |
| struct cx88_core *core = drv->core; |
| struct cx8802_dev *dev = core->dvbdev; |
| |
| /* blackbird */ |
| blackbird_unregister_video(drv->core->dvbdev); |
| v4l2_ctrl_handler_free(&dev->cxhdl.hdl); |
| |
| return 0; |
| } |
| |
| static struct cx8802_driver cx8802_blackbird_driver = { |
| .type_id = CX88_MPEG_BLACKBIRD, |
| .hw_access = CX8802_DRVCTL_SHARED, |
| .probe = cx8802_blackbird_probe, |
| .remove = cx8802_blackbird_remove, |
| .advise_acquire = cx8802_blackbird_advise_acquire, |
| .advise_release = cx8802_blackbird_advise_release, |
| }; |
| |
| static int __init blackbird_init(void) |
| { |
| pr_info("cx2388x blackbird driver version %s loaded\n", |
| CX88_VERSION); |
| return cx8802_register_driver(&cx8802_blackbird_driver); |
| } |
| |
| static void __exit blackbird_fini(void) |
| { |
| cx8802_unregister_driver(&cx8802_blackbird_driver); |
| } |
| |
| module_init(blackbird_init); |
| module_exit(blackbird_fini); |