| // SPDX-License-Identifier: BSD-3-Clause |
| // Copyright (c) 2019, The Linux Foundation. All rights reserved. |
| |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/spmi/spmi.h> |
| |
| &spmi_bus { |
| pm6150l_lsid4: pmic@4 { |
| compatible = "qcom,pm6150l", "qcom,spmi-pmic"; |
| reg = <0x4 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm6150l_adc: adc@3100 { |
| compatible = "qcom,spmi-adc5"; |
| reg = <0x3100>; |
| interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #io-channel-cells = <1>; |
| |
| adc-chan@0 { |
| reg = <ADC5_REF_GND>; |
| qcom,pre-scaling = <1 1>; |
| label = "ref_gnd"; |
| }; |
| |
| adc-chan@1 { |
| reg = <ADC5_1P25VREF>; |
| qcom,pre-scaling = <1 1>; |
| label = "vref_1p25"; |
| }; |
| |
| adc-chan@6 { |
| reg = <ADC5_DIE_TEMP>; |
| qcom,pre-scaling = <1 1>; |
| label = "die_temp"; |
| }; |
| |
| adc-chan@83 { |
| reg = <ADC5_VPH_PWR>; |
| qcom,pre-scaling = <1 3>; |
| label = "vph_pwr"; |
| }; |
| }; |
| |
| pm6150l_adc_tm: adc-tm@3500 { |
| compatible = "qcom,spmi-adc-tm5"; |
| reg = <0x3500>; |
| interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| #thermal-sensor-cells = <1>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| pm6150l_gpio: gpios@c000 { |
| compatible = "qcom,pm6150l-gpio", "qcom,spmi-gpio"; |
| reg = <0xc000>; |
| gpio-controller; |
| gpio-ranges = <&pm6150l_gpio 0 0 12>; |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| pm6150l_lsid5: pmic@5 { |
| compatible = "qcom,pm6150l", "qcom,spmi-pmic"; |
| reg = <0x5 SPMI_USID>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| pm6150l_wled: leds@d800 { |
| compatible = "qcom,pm6150l-wled"; |
| reg = <0xd800>, <0xd900>; |
| interrupts = <0x5 0xd8 0x1 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "ovp"; |
| label = "backlight"; |
| |
| status = "disabled"; |
| }; |
| }; |
| }; |
