Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt

BCM2835 Top-Level ("ARMCTRL") Interrupt Controller

The BCM2835 contains a custom top-level interrupt controller, which supports
72 interrupt sources using a 2-level register scheme. The interrupt
controller, or the HW block containing it, is referred to occasionally
as "armctrl" in the SoC documentation, hence naming of this binding.

The BCM2836 contains the same interrupt controller with the same
interrupts, but the per-CPU interrupt controller is the root, and an
interrupt there indicates that the ARMCTRL has an interrupt to handle.

Required properties:

- compatible : should be "brcm,bcm2835-armctrl-ic" or
                 "brcm,bcm2836-armctrl-ic"
- reg : Specifies base physical address and size of the registers.
- interrupt-controller : Identifies the node as an interrupt controller
- #interrupt-cells : Specifies the number of cells needed to encode an
  interrupt source. The value shall be 2.

  The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic
  pending" register, or 1/2 respectively for interrupts in the "IRQ pending
  1/2" register.

  The 2nd cell contains the interrupt number within the bank. Valid values
  are 0..7 for bank 0, and 0..31 for bank 1.

Additional required properties for brcm,bcm2836-armctrl-ic:
- interrupts : Specifies the interrupt on the parent for this interrupt
  controller to handle.

The interrupt sources are as follows:

Bank 0:
0: ARM_TIMER
1: ARM_MAILBOX
2: ARM_DOORBELL_0
3: ARM_DOORBELL_1
4: VPU0_HALTED
5: VPU1_HALTED
6: ILLEGAL_TYPE0
7: ILLEGAL_TYPE1

Bank 1:
0: TIMER0
1: TIMER1
2: TIMER2
3: TIMER3
4: CODEC0
5: CODEC1
6: CODEC2
7: VC_JPEG
8: ISP
9: VC_USB
10: VC_3D
11: TRANSPOSER
12: MULTICORESYNC0
13: MULTICORESYNC1
14: MULTICORESYNC2
15: MULTICORESYNC3
16: DMA0
17: DMA1
18: VC_DMA2
19: VC_DMA3
20: DMA4
21: DMA5
22: DMA6
23: DMA7
24: DMA8
25: DMA9
26: DMA10
27: DMA11-14 - shared interrupt for DMA 11 to 14
28: DMAALL - triggers on all dma interrupts (including channel 15)
29: AUX
30: ARM
31: VPUDMA

Bank 2:
0: HOSTPORT
1: VIDEOSCALER
2: CCP2TX
3: SDC
4: DSI0
5: AVE
6: CAM0
7: CAM1
8: HDMI0
9: HDMI1
10: PIXELVALVE1
11: I2CSPISLV
12: DSI1
13: PWA0
14: PWA1
15: CPR
16: SMI
17: GPIO0
18: GPIO1
19: GPIO2
20: GPIO3
21: VC_I2C
22: VC_SPI
23: VC_I2SPCM
24: VC_SDIO
25: VC_UART
26: SLIMBUS
27: VEC
28: CPG
29: RNG
30: VC_ARASANSDIO
31: AVSPMON

Example:

/* BCM2835, first level */
intc: interrupt-controller {
	compatible = "brcm,bcm2835-armctrl-ic";
	reg = <0x7e00b200 0x200>;
	interrupt-controller;
	#interrupt-cells = <2>;
};

/* BCM2836, second level */
intc: interrupt-controller {
	compatible = "brcm,bcm2836-armctrl-ic";
	reg = <0x7e00b200 0x200>;
	interrupt-controller;
	#interrupt-cells = <2>;

	interrupt-parent = <&local_intc>;
	interrupts = <8>;
};