| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * This driver enables Trace Buffer Extension (TRBE) as a per-cpu coresight |
| * sink device could then pair with an appropriate per-cpu coresight source |
| * device (ETE) thus generating required trace data. Trace can be enabled |
| * via the perf framework. |
| * |
| * The AUX buffer handling is inspired from Arm SPE PMU driver. |
| * |
| * Copyright (C) 2020 ARM Ltd. |
| * |
| * Author: Anshuman Khandual <anshuman.khandual@arm.com> |
| */ |
| #define DRVNAME "arm_trbe" |
| |
| #define pr_fmt(fmt) DRVNAME ": " fmt |
| |
| #include <asm/barrier.h> |
| #include "coresight-trbe.h" |
| |
| #define PERF_IDX2OFF(idx, buf) ((idx) % ((buf)->nr_pages << PAGE_SHIFT)) |
| |
| /* |
| * A padding packet that will help the user space tools |
| * in skipping relevant sections in the captured trace |
| * data which could not be decoded. TRBE doesn't support |
| * formatting the trace data, unlike the legacy CoreSight |
| * sinks and thus we use ETE trace packets to pad the |
| * sections of the buffer. |
| */ |
| #define ETE_IGNORE_PACKET 0x70 |
| |
| /* |
| * Minimum amount of meaningful trace will contain: |
| * A-Sync, Trace Info, Trace On, Address, Atom. |
| * This is about 44bytes of ETE trace. To be on |
| * the safer side, we assume 64bytes is the minimum |
| * space required for a meaningful session, before |
| * we hit a "WRAP" event. |
| */ |
| #define TRBE_TRACE_MIN_BUF_SIZE 64 |
| |
| enum trbe_fault_action { |
| TRBE_FAULT_ACT_WRAP, |
| TRBE_FAULT_ACT_SPURIOUS, |
| TRBE_FAULT_ACT_FATAL, |
| }; |
| |
| struct trbe_buf { |
| /* |
| * Even though trbe_base represents vmap() |
| * mapped allocated buffer's start address, |
| * it's being as unsigned long for various |
| * arithmetic and comparision operations & |
| * also to be consistent with trbe_write & |
| * trbe_limit sibling pointers. |
| */ |
| unsigned long trbe_base; |
| unsigned long trbe_limit; |
| unsigned long trbe_write; |
| int nr_pages; |
| void **pages; |
| bool snapshot; |
| struct trbe_cpudata *cpudata; |
| }; |
| |
| struct trbe_cpudata { |
| bool trbe_flag; |
| u64 trbe_align; |
| int cpu; |
| enum cs_mode mode; |
| struct trbe_buf *buf; |
| struct trbe_drvdata *drvdata; |
| }; |
| |
| struct trbe_drvdata { |
| struct trbe_cpudata __percpu *cpudata; |
| struct perf_output_handle * __percpu *handle; |
| struct hlist_node hotplug_node; |
| int irq; |
| cpumask_t supported_cpus; |
| enum cpuhp_state trbe_online; |
| struct platform_device *pdev; |
| }; |
| |
| static int trbe_alloc_node(struct perf_event *event) |
| { |
| if (event->cpu == -1) |
| return NUMA_NO_NODE; |
| return cpu_to_node(event->cpu); |
| } |
| |
| static void trbe_drain_buffer(void) |
| { |
| tsb_csync(); |
| dsb(nsh); |
| } |
| |
| static void trbe_drain_and_disable_local(void) |
| { |
| u64 trblimitr = read_sysreg_s(SYS_TRBLIMITR_EL1); |
| |
| trbe_drain_buffer(); |
| |
| /* |
| * Disable the TRBE without clearing LIMITPTR which |
| * might be required for fetching the buffer limits. |
| */ |
| trblimitr &= ~TRBLIMITR_ENABLE; |
| write_sysreg_s(trblimitr, SYS_TRBLIMITR_EL1); |
| isb(); |
| } |
| |
| static void trbe_reset_local(void) |
| { |
| trbe_drain_and_disable_local(); |
| write_sysreg_s(0, SYS_TRBLIMITR_EL1); |
| write_sysreg_s(0, SYS_TRBPTR_EL1); |
| write_sysreg_s(0, SYS_TRBBASER_EL1); |
| write_sysreg_s(0, SYS_TRBSR_EL1); |
| } |
| |
| static void trbe_stop_and_truncate_event(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| |
| /* |
| * We cannot proceed with the buffer collection and we |
| * do not have any data for the current session. The |
| * etm_perf driver expects to close out the aux_buffer |
| * at event_stop(). So disable the TRBE here and leave |
| * the update_buffer() to return a 0 size. |
| */ |
| trbe_drain_and_disable_local(); |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED); |
| *this_cpu_ptr(buf->cpudata->drvdata->handle) = NULL; |
| } |
| |
| /* |
| * TRBE Buffer Management |
| * |
| * The TRBE buffer spans from the base pointer till the limit pointer. When enabled, |
| * it starts writing trace data from the write pointer onward till the limit pointer. |
| * When the write pointer reaches the address just before the limit pointer, it gets |
| * wrapped around again to the base pointer. This is called a TRBE wrap event, which |
| * generates a maintenance interrupt when operated in WRAP or FILL mode. This driver |
| * uses FILL mode, where the TRBE stops the trace collection at wrap event. The IRQ |
| * handler updates the AUX buffer and re-enables the TRBE with updated WRITE and |
| * LIMIT pointers. |
| * |
| * Wrap around with an IRQ |
| * ------ < ------ < ------- < ----- < ----- |
| * | | |
| * ------ > ------ > ------- > ----- > ----- |
| * |
| * +---------------+-----------------------+ |
| * | | | |
| * +---------------+-----------------------+ |
| * Base Pointer Write Pointer Limit Pointer |
| * |
| * The base and limit pointers always needs to be PAGE_SIZE aligned. But the write |
| * pointer can be aligned to the implementation defined TRBE trace buffer alignment |
| * as captured in trbe_cpudata->trbe_align. |
| * |
| * |
| * head tail wakeup |
| * +---------------------------------------+----- ~ ~ ------ |
| * |$$$$$$$|################|$$$$$$$$$$$$$$| | |
| * +---------------------------------------+----- ~ ~ ------ |
| * Base Pointer Write Pointer Limit Pointer |
| * |
| * The perf_output_handle indices (head, tail, wakeup) are monotonically increasing |
| * values which tracks all the driver writes and user reads from the perf auxiliary |
| * buffer. Generally [head..tail] is the area where the driver can write into unless |
| * the wakeup is behind the tail. Enabled TRBE buffer span needs to be adjusted and |
| * configured depending on the perf_output_handle indices, so that the driver does |
| * not override into areas in the perf auxiliary buffer which is being or yet to be |
| * consumed from the user space. The enabled TRBE buffer area is a moving subset of |
| * the allocated perf auxiliary buffer. |
| */ |
| static void trbe_pad_buf(struct perf_output_handle *handle, int len) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| u64 head = PERF_IDX2OFF(handle->head, buf); |
| |
| memset((void *)buf->trbe_base + head, ETE_IGNORE_PACKET, len); |
| if (!buf->snapshot) |
| perf_aux_output_skip(handle, len); |
| } |
| |
| static unsigned long trbe_snapshot_offset(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| |
| /* |
| * The ETE trace has alignment synchronization packets allowing |
| * the decoder to reset in case of an overflow or corruption. |
| * So we can use the entire buffer for the snapshot mode. |
| */ |
| return buf->nr_pages * PAGE_SIZE; |
| } |
| |
| /* |
| * TRBE Limit Calculation |
| * |
| * The following markers are used to illustrate various TRBE buffer situations. |
| * |
| * $$$$ - Data area, unconsumed captured trace data, not to be overridden |
| * #### - Free area, enabled, trace will be written |
| * %%%% - Free area, disabled, trace will not be written |
| * ==== - Free area, padded with ETE_IGNORE_PACKET, trace will be skipped |
| */ |
| static unsigned long __trbe_normal_offset(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| struct trbe_cpudata *cpudata = buf->cpudata; |
| const u64 bufsize = buf->nr_pages * PAGE_SIZE; |
| u64 limit = bufsize; |
| u64 head, tail, wakeup; |
| |
| head = PERF_IDX2OFF(handle->head, buf); |
| |
| /* |
| * head |
| * ------->| |
| * | |
| * head TRBE align tail |
| * +----|-------|---------------|-------+ |
| * |$$$$|=======|###############|$$$$$$$| |
| * +----|-------|---------------|-------+ |
| * trbe_base trbe_base + nr_pages |
| * |
| * Perf aux buffer output head position can be misaligned depending on |
| * various factors including user space reads. In case misaligned, head |
| * needs to be aligned before TRBE can be configured. Pad the alignment |
| * gap with ETE_IGNORE_PACKET bytes that will be ignored by user tools |
| * and skip this section thus advancing the head. |
| */ |
| if (!IS_ALIGNED(head, cpudata->trbe_align)) { |
| unsigned long delta = roundup(head, cpudata->trbe_align) - head; |
| |
| delta = min(delta, handle->size); |
| trbe_pad_buf(handle, delta); |
| head = PERF_IDX2OFF(handle->head, buf); |
| } |
| |
| /* |
| * head = tail (size = 0) |
| * +----|-------------------------------+ |
| * |$$$$|$$$$$$$$$$$$$$$$$$$$$$$$$$$$$$ | |
| * +----|-------------------------------+ |
| * trbe_base trbe_base + nr_pages |
| * |
| * Perf aux buffer does not have any space for the driver to write into. |
| * Just communicate trace truncation event to the user space by marking |
| * it with PERF_AUX_FLAG_TRUNCATED. |
| */ |
| if (!handle->size) { |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED); |
| return 0; |
| } |
| |
| /* Compute the tail and wakeup indices now that we've aligned head */ |
| tail = PERF_IDX2OFF(handle->head + handle->size, buf); |
| wakeup = PERF_IDX2OFF(handle->wakeup, buf); |
| |
| /* |
| * Lets calculate the buffer area which TRBE could write into. There |
| * are three possible scenarios here. Limit needs to be aligned with |
| * PAGE_SIZE per the TRBE requirement. Always avoid clobbering the |
| * unconsumed data. |
| * |
| * 1) head < tail |
| * |
| * head tail |
| * +----|-----------------------|-------+ |
| * |$$$$|#######################|$$$$$$$| |
| * +----|-----------------------|-------+ |
| * trbe_base limit trbe_base + nr_pages |
| * |
| * TRBE could write into [head..tail] area. Unless the tail is right at |
| * the end of the buffer, neither an wrap around nor an IRQ is expected |
| * while being enabled. |
| * |
| * 2) head == tail |
| * |
| * head = tail (size > 0) |
| * +----|-------------------------------+ |
| * |%%%%|###############################| |
| * +----|-------------------------------+ |
| * trbe_base limit = trbe_base + nr_pages |
| * |
| * TRBE should just write into [head..base + nr_pages] area even though |
| * the entire buffer is empty. Reason being, when the trace reaches the |
| * end of the buffer, it will just wrap around with an IRQ giving an |
| * opportunity to reconfigure the buffer. |
| * |
| * 3) tail < head |
| * |
| * tail head |
| * +----|-----------------------|-------+ |
| * |%%%%|$$$$$$$$$$$$$$$$$$$$$$$|#######| |
| * +----|-----------------------|-------+ |
| * trbe_base limit = trbe_base + nr_pages |
| * |
| * TRBE should just write into [head..base + nr_pages] area even though |
| * the [trbe_base..tail] is also empty. Reason being, when the trace |
| * reaches the end of the buffer, it will just wrap around with an IRQ |
| * giving an opportunity to reconfigure the buffer. |
| */ |
| if (head < tail) |
| limit = round_down(tail, PAGE_SIZE); |
| |
| /* |
| * Wakeup may be arbitrarily far into the future. If it's not in the |
| * current generation, either we'll wrap before hitting it, or it's |
| * in the past and has been handled already. |
| * |
| * If there's a wakeup before we wrap, arrange to be woken up by the |
| * page boundary following it. Keep the tail boundary if that's lower. |
| * |
| * head wakeup tail |
| * +----|---------------|-------|-------+ |
| * |$$$$|###############|%%%%%%%|$$$$$$$| |
| * +----|---------------|-------|-------+ |
| * trbe_base limit trbe_base + nr_pages |
| */ |
| if (handle->wakeup < (handle->head + handle->size) && head <= wakeup) |
| limit = min(limit, round_up(wakeup, PAGE_SIZE)); |
| |
| /* |
| * There are two situation when this can happen i.e limit is before |
| * the head and hence TRBE cannot be configured. |
| * |
| * 1) head < tail (aligned down with PAGE_SIZE) and also they are both |
| * within the same PAGE size range. |
| * |
| * PAGE_SIZE |
| * |----------------------| |
| * |
| * limit head tail |
| * +------------|------|--------|-------+ |
| * |$$$$$$$$$$$$$$$$$$$|========|$$$$$$$| |
| * +------------|------|--------|-------+ |
| * trbe_base trbe_base + nr_pages |
| * |
| * 2) head < wakeup (aligned up with PAGE_SIZE) < tail and also both |
| * head and wakeup are within same PAGE size range. |
| * |
| * PAGE_SIZE |
| * |----------------------| |
| * |
| * limit head wakeup tail |
| * +----|------|-------|--------|-------+ |
| * |$$$$$$$$$$$|=======|========|$$$$$$$| |
| * +----|------|-------|--------|-------+ |
| * trbe_base trbe_base + nr_pages |
| */ |
| if (limit > head) |
| return limit; |
| |
| trbe_pad_buf(handle, handle->size); |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED); |
| return 0; |
| } |
| |
| static unsigned long trbe_normal_offset(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = perf_get_aux(handle); |
| u64 limit = __trbe_normal_offset(handle); |
| u64 head = PERF_IDX2OFF(handle->head, buf); |
| |
| /* |
| * If the head is too close to the limit and we don't |
| * have space for a meaningful run, we rather pad it |
| * and start fresh. |
| */ |
| if (limit && (limit - head < TRBE_TRACE_MIN_BUF_SIZE)) { |
| trbe_pad_buf(handle, limit - head); |
| limit = __trbe_normal_offset(handle); |
| } |
| return limit; |
| } |
| |
| static unsigned long compute_trbe_buffer_limit(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| unsigned long offset; |
| |
| if (buf->snapshot) |
| offset = trbe_snapshot_offset(handle); |
| else |
| offset = trbe_normal_offset(handle); |
| return buf->trbe_base + offset; |
| } |
| |
| static void clr_trbe_status(void) |
| { |
| u64 trbsr = read_sysreg_s(SYS_TRBSR_EL1); |
| |
| WARN_ON(is_trbe_enabled()); |
| trbsr &= ~TRBSR_IRQ; |
| trbsr &= ~TRBSR_TRG; |
| trbsr &= ~TRBSR_WRAP; |
| trbsr &= ~(TRBSR_EC_MASK << TRBSR_EC_SHIFT); |
| trbsr &= ~(TRBSR_BSC_MASK << TRBSR_BSC_SHIFT); |
| trbsr &= ~TRBSR_STOP; |
| write_sysreg_s(trbsr, SYS_TRBSR_EL1); |
| } |
| |
| static void set_trbe_limit_pointer_enabled(unsigned long addr) |
| { |
| u64 trblimitr = read_sysreg_s(SYS_TRBLIMITR_EL1); |
| |
| WARN_ON(!IS_ALIGNED(addr, (1UL << TRBLIMITR_LIMIT_SHIFT))); |
| WARN_ON(!IS_ALIGNED(addr, PAGE_SIZE)); |
| |
| trblimitr &= ~TRBLIMITR_NVM; |
| trblimitr &= ~(TRBLIMITR_FILL_MODE_MASK << TRBLIMITR_FILL_MODE_SHIFT); |
| trblimitr &= ~(TRBLIMITR_TRIG_MODE_MASK << TRBLIMITR_TRIG_MODE_SHIFT); |
| trblimitr &= ~(TRBLIMITR_LIMIT_MASK << TRBLIMITR_LIMIT_SHIFT); |
| |
| /* |
| * Fill trace buffer mode is used here while configuring the |
| * TRBE for trace capture. In this particular mode, the trace |
| * collection is stopped and a maintenance interrupt is raised |
| * when the current write pointer wraps. This pause in trace |
| * collection gives the software an opportunity to capture the |
| * trace data in the interrupt handler, before reconfiguring |
| * the TRBE. |
| */ |
| trblimitr |= (TRBE_FILL_MODE_FILL & TRBLIMITR_FILL_MODE_MASK) << TRBLIMITR_FILL_MODE_SHIFT; |
| |
| /* |
| * Trigger mode is not used here while configuring the TRBE for |
| * the trace capture. Hence just keep this in the ignore mode. |
| */ |
| trblimitr |= (TRBE_TRIG_MODE_IGNORE & TRBLIMITR_TRIG_MODE_MASK) << |
| TRBLIMITR_TRIG_MODE_SHIFT; |
| trblimitr |= (addr & PAGE_MASK); |
| |
| trblimitr |= TRBLIMITR_ENABLE; |
| write_sysreg_s(trblimitr, SYS_TRBLIMITR_EL1); |
| |
| /* Synchronize the TRBE enable event */ |
| isb(); |
| } |
| |
| static void trbe_enable_hw(struct trbe_buf *buf) |
| { |
| WARN_ON(buf->trbe_write < buf->trbe_base); |
| WARN_ON(buf->trbe_write >= buf->trbe_limit); |
| set_trbe_disabled(); |
| isb(); |
| clr_trbe_status(); |
| set_trbe_base_pointer(buf->trbe_base); |
| set_trbe_write_pointer(buf->trbe_write); |
| |
| /* |
| * Synchronize all the register updates |
| * till now before enabling the TRBE. |
| */ |
| isb(); |
| set_trbe_limit_pointer_enabled(buf->trbe_limit); |
| } |
| |
| static enum trbe_fault_action trbe_get_fault_act(u64 trbsr) |
| { |
| int ec = get_trbe_ec(trbsr); |
| int bsc = get_trbe_bsc(trbsr); |
| |
| WARN_ON(is_trbe_running(trbsr)); |
| if (is_trbe_trg(trbsr) || is_trbe_abort(trbsr)) |
| return TRBE_FAULT_ACT_FATAL; |
| |
| if ((ec == TRBE_EC_STAGE1_ABORT) || (ec == TRBE_EC_STAGE2_ABORT)) |
| return TRBE_FAULT_ACT_FATAL; |
| |
| if (is_trbe_wrap(trbsr) && (ec == TRBE_EC_OTHERS) && (bsc == TRBE_BSC_FILLED)) { |
| if (get_trbe_write_pointer() == get_trbe_base_pointer()) |
| return TRBE_FAULT_ACT_WRAP; |
| } |
| return TRBE_FAULT_ACT_SPURIOUS; |
| } |
| |
| static void *arm_trbe_alloc_buffer(struct coresight_device *csdev, |
| struct perf_event *event, void **pages, |
| int nr_pages, bool snapshot) |
| { |
| struct trbe_buf *buf; |
| struct page **pglist; |
| int i; |
| |
| /* |
| * TRBE LIMIT and TRBE WRITE pointers must be page aligned. But with |
| * just a single page, there would not be any room left while writing |
| * into a partially filled TRBE buffer after the page size alignment. |
| * Hence restrict the minimum buffer size as two pages. |
| */ |
| if (nr_pages < 2) |
| return NULL; |
| |
| buf = kzalloc_node(sizeof(*buf), GFP_KERNEL, trbe_alloc_node(event)); |
| if (!buf) |
| return ERR_PTR(-ENOMEM); |
| |
| pglist = kcalloc(nr_pages, sizeof(*pglist), GFP_KERNEL); |
| if (!pglist) { |
| kfree(buf); |
| return ERR_PTR(-ENOMEM); |
| } |
| |
| for (i = 0; i < nr_pages; i++) |
| pglist[i] = virt_to_page(pages[i]); |
| |
| buf->trbe_base = (unsigned long)vmap(pglist, nr_pages, VM_MAP, PAGE_KERNEL); |
| if (!buf->trbe_base) { |
| kfree(pglist); |
| kfree(buf); |
| return ERR_PTR(-ENOMEM); |
| } |
| buf->trbe_limit = buf->trbe_base + nr_pages * PAGE_SIZE; |
| buf->trbe_write = buf->trbe_base; |
| buf->snapshot = snapshot; |
| buf->nr_pages = nr_pages; |
| buf->pages = pages; |
| kfree(pglist); |
| return buf; |
| } |
| |
| static void arm_trbe_free_buffer(void *config) |
| { |
| struct trbe_buf *buf = config; |
| |
| vunmap((void *)buf->trbe_base); |
| kfree(buf); |
| } |
| |
| static unsigned long arm_trbe_update_buffer(struct coresight_device *csdev, |
| struct perf_output_handle *handle, |
| void *config) |
| { |
| struct trbe_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent); |
| struct trbe_cpudata *cpudata = dev_get_drvdata(&csdev->dev); |
| struct trbe_buf *buf = config; |
| enum trbe_fault_action act; |
| unsigned long size, offset; |
| unsigned long write, base, status; |
| unsigned long flags; |
| |
| WARN_ON(buf->cpudata != cpudata); |
| WARN_ON(cpudata->cpu != smp_processor_id()); |
| WARN_ON(cpudata->drvdata != drvdata); |
| if (cpudata->mode != CS_MODE_PERF) |
| return 0; |
| |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_CORESIGHT_FORMAT_RAW); |
| |
| /* |
| * We are about to disable the TRBE. And this could in turn |
| * fill up the buffer triggering, an IRQ. This could be consumed |
| * by the PE asynchronously, causing a race here against |
| * the IRQ handler in closing out the handle. So, let us |
| * make sure the IRQ can't trigger while we are collecting |
| * the buffer. We also make sure that a WRAP event is handled |
| * accordingly. |
| */ |
| local_irq_save(flags); |
| |
| /* |
| * If the TRBE was disabled due to lack of space in the AUX buffer or a |
| * spurious fault, the driver leaves it disabled, truncating the buffer. |
| * Since the etm_perf driver expects to close out the AUX buffer, the |
| * driver skips it. Thus, just pass in 0 size here to indicate that the |
| * buffer was truncated. |
| */ |
| if (!is_trbe_enabled()) { |
| size = 0; |
| goto done; |
| } |
| /* |
| * perf handle structure needs to be shared with the TRBE IRQ handler for |
| * capturing trace data and restarting the handle. There is a probability |
| * of an undefined reference based crash when etm event is being stopped |
| * while a TRBE IRQ also getting processed. This happens due the release |
| * of perf handle via perf_aux_output_end() in etm_event_stop(). Stopping |
| * the TRBE here will ensure that no IRQ could be generated when the perf |
| * handle gets freed in etm_event_stop(). |
| */ |
| trbe_drain_and_disable_local(); |
| write = get_trbe_write_pointer(); |
| base = get_trbe_base_pointer(); |
| |
| /* Check if there is a pending interrupt and handle it here */ |
| status = read_sysreg_s(SYS_TRBSR_EL1); |
| if (is_trbe_irq(status)) { |
| |
| /* |
| * Now that we are handling the IRQ here, clear the IRQ |
| * from the status, to let the irq handler know that it |
| * is taken care of. |
| */ |
| clr_trbe_irq(); |
| isb(); |
| |
| act = trbe_get_fault_act(status); |
| /* |
| * If this was not due to a WRAP event, we have some |
| * errors and as such buffer is empty. |
| */ |
| if (act != TRBE_FAULT_ACT_WRAP) { |
| size = 0; |
| goto done; |
| } |
| |
| /* |
| * Otherwise, the buffer is full and the write pointer |
| * has reached base. Adjust this back to the Limit pointer |
| * for correct size. Also, mark the buffer truncated. |
| */ |
| write = get_trbe_limit_pointer(); |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_TRUNCATED); |
| } |
| |
| offset = write - base; |
| if (WARN_ON_ONCE(offset < PERF_IDX2OFF(handle->head, buf))) |
| size = 0; |
| else |
| size = offset - PERF_IDX2OFF(handle->head, buf); |
| |
| done: |
| local_irq_restore(flags); |
| |
| if (buf->snapshot) |
| handle->head += size; |
| return size; |
| } |
| |
| static int arm_trbe_enable(struct coresight_device *csdev, u32 mode, void *data) |
| { |
| struct trbe_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent); |
| struct trbe_cpudata *cpudata = dev_get_drvdata(&csdev->dev); |
| struct perf_output_handle *handle = data; |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| |
| WARN_ON(cpudata->cpu != smp_processor_id()); |
| WARN_ON(cpudata->drvdata != drvdata); |
| if (mode != CS_MODE_PERF) |
| return -EINVAL; |
| |
| *this_cpu_ptr(drvdata->handle) = handle; |
| cpudata->buf = buf; |
| cpudata->mode = mode; |
| buf->cpudata = cpudata; |
| buf->trbe_limit = compute_trbe_buffer_limit(handle); |
| buf->trbe_write = buf->trbe_base + PERF_IDX2OFF(handle->head, buf); |
| if (buf->trbe_limit == buf->trbe_base) { |
| trbe_stop_and_truncate_event(handle); |
| return 0; |
| } |
| trbe_enable_hw(buf); |
| return 0; |
| } |
| |
| static int arm_trbe_disable(struct coresight_device *csdev) |
| { |
| struct trbe_drvdata *drvdata = dev_get_drvdata(csdev->dev.parent); |
| struct trbe_cpudata *cpudata = dev_get_drvdata(&csdev->dev); |
| struct trbe_buf *buf = cpudata->buf; |
| |
| WARN_ON(buf->cpudata != cpudata); |
| WARN_ON(cpudata->cpu != smp_processor_id()); |
| WARN_ON(cpudata->drvdata != drvdata); |
| if (cpudata->mode != CS_MODE_PERF) |
| return -EINVAL; |
| |
| trbe_drain_and_disable_local(); |
| buf->cpudata = NULL; |
| cpudata->buf = NULL; |
| cpudata->mode = CS_MODE_DISABLED; |
| return 0; |
| } |
| |
| static void trbe_handle_spurious(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| |
| buf->trbe_limit = compute_trbe_buffer_limit(handle); |
| buf->trbe_write = buf->trbe_base + PERF_IDX2OFF(handle->head, buf); |
| if (buf->trbe_limit == buf->trbe_base) { |
| trbe_drain_and_disable_local(); |
| return; |
| } |
| trbe_enable_hw(buf); |
| } |
| |
| static void trbe_handle_overflow(struct perf_output_handle *handle) |
| { |
| struct perf_event *event = handle->event; |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| unsigned long offset, size; |
| struct etm_event_data *event_data; |
| |
| offset = get_trbe_limit_pointer() - get_trbe_base_pointer(); |
| size = offset - PERF_IDX2OFF(handle->head, buf); |
| if (buf->snapshot) |
| handle->head += size; |
| |
| /* |
| * Mark the buffer as truncated, as we have stopped the trace |
| * collection upon the WRAP event, without stopping the source. |
| */ |
| perf_aux_output_flag(handle, PERF_AUX_FLAG_CORESIGHT_FORMAT_RAW | |
| PERF_AUX_FLAG_TRUNCATED); |
| perf_aux_output_end(handle, size); |
| event_data = perf_aux_output_begin(handle, event); |
| if (!event_data) { |
| /* |
| * We are unable to restart the trace collection, |
| * thus leave the TRBE disabled. The etm-perf driver |
| * is able to detect this with a disconnected handle |
| * (handle->event = NULL). |
| */ |
| trbe_drain_and_disable_local(); |
| *this_cpu_ptr(buf->cpudata->drvdata->handle) = NULL; |
| return; |
| } |
| buf->trbe_limit = compute_trbe_buffer_limit(handle); |
| buf->trbe_write = buf->trbe_base + PERF_IDX2OFF(handle->head, buf); |
| if (buf->trbe_limit == buf->trbe_base) { |
| trbe_stop_and_truncate_event(handle); |
| return; |
| } |
| *this_cpu_ptr(buf->cpudata->drvdata->handle) = handle; |
| trbe_enable_hw(buf); |
| } |
| |
| static bool is_perf_trbe(struct perf_output_handle *handle) |
| { |
| struct trbe_buf *buf = etm_perf_sink_config(handle); |
| struct trbe_cpudata *cpudata = buf->cpudata; |
| struct trbe_drvdata *drvdata = cpudata->drvdata; |
| int cpu = smp_processor_id(); |
| |
| WARN_ON(buf->trbe_base != get_trbe_base_pointer()); |
| WARN_ON(buf->trbe_limit != get_trbe_limit_pointer()); |
| |
| if (cpudata->mode != CS_MODE_PERF) |
| return false; |
| |
| if (cpudata->cpu != cpu) |
| return false; |
| |
| if (!cpumask_test_cpu(cpu, &drvdata->supported_cpus)) |
| return false; |
| |
| return true; |
| } |
| |
| static irqreturn_t arm_trbe_irq_handler(int irq, void *dev) |
| { |
| struct perf_output_handle **handle_ptr = dev; |
| struct perf_output_handle *handle = *handle_ptr; |
| enum trbe_fault_action act; |
| u64 status; |
| |
| /* |
| * Ensure the trace is visible to the CPUs and |
| * any external aborts have been resolved. |
| */ |
| trbe_drain_and_disable_local(); |
| |
| status = read_sysreg_s(SYS_TRBSR_EL1); |
| /* |
| * If the pending IRQ was handled by update_buffer callback |
| * we have nothing to do here. |
| */ |
| if (!is_trbe_irq(status)) |
| return IRQ_NONE; |
| |
| clr_trbe_irq(); |
| isb(); |
| |
| if (WARN_ON_ONCE(!handle) || !perf_get_aux(handle)) |
| return IRQ_NONE; |
| |
| if (!is_perf_trbe(handle)) |
| return IRQ_NONE; |
| |
| /* |
| * Ensure perf callbacks have completed, which may disable |
| * the trace buffer in response to a TRUNCATION flag. |
| */ |
| irq_work_run(); |
| |
| act = trbe_get_fault_act(status); |
| switch (act) { |
| case TRBE_FAULT_ACT_WRAP: |
| trbe_handle_overflow(handle); |
| break; |
| case TRBE_FAULT_ACT_SPURIOUS: |
| trbe_handle_spurious(handle); |
| break; |
| case TRBE_FAULT_ACT_FATAL: |
| trbe_stop_and_truncate_event(handle); |
| break; |
| } |
| return IRQ_HANDLED; |
| } |
| |
| static const struct coresight_ops_sink arm_trbe_sink_ops = { |
| .enable = arm_trbe_enable, |
| .disable = arm_trbe_disable, |
| .alloc_buffer = arm_trbe_alloc_buffer, |
| .free_buffer = arm_trbe_free_buffer, |
| .update_buffer = arm_trbe_update_buffer, |
| }; |
| |
| static const struct coresight_ops arm_trbe_cs_ops = { |
| .sink_ops = &arm_trbe_sink_ops, |
| }; |
| |
| static ssize_t align_show(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct trbe_cpudata *cpudata = dev_get_drvdata(dev); |
| |
| return sprintf(buf, "%llx\n", cpudata->trbe_align); |
| } |
| static DEVICE_ATTR_RO(align); |
| |
| static ssize_t flag_show(struct device *dev, struct device_attribute *attr, char *buf) |
| { |
| struct trbe_cpudata *cpudata = dev_get_drvdata(dev); |
| |
| return sprintf(buf, "%d\n", cpudata->trbe_flag); |
| } |
| static DEVICE_ATTR_RO(flag); |
| |
| static struct attribute *arm_trbe_attrs[] = { |
| &dev_attr_align.attr, |
| &dev_attr_flag.attr, |
| NULL, |
| }; |
| |
| static const struct attribute_group arm_trbe_group = { |
| .attrs = arm_trbe_attrs, |
| }; |
| |
| static const struct attribute_group *arm_trbe_groups[] = { |
| &arm_trbe_group, |
| NULL, |
| }; |
| |
| static void arm_trbe_enable_cpu(void *info) |
| { |
| struct trbe_drvdata *drvdata = info; |
| |
| trbe_reset_local(); |
| enable_percpu_irq(drvdata->irq, IRQ_TYPE_NONE); |
| } |
| |
| static void arm_trbe_register_coresight_cpu(struct trbe_drvdata *drvdata, int cpu) |
| { |
| struct trbe_cpudata *cpudata = per_cpu_ptr(drvdata->cpudata, cpu); |
| struct coresight_device *trbe_csdev = coresight_get_percpu_sink(cpu); |
| struct coresight_desc desc = { 0 }; |
| struct device *dev; |
| |
| if (WARN_ON(trbe_csdev)) |
| return; |
| |
| dev = &cpudata->drvdata->pdev->dev; |
| desc.name = devm_kasprintf(dev, GFP_KERNEL, "trbe%d", cpu); |
| if (!desc.name) |
| goto cpu_clear; |
| |
| desc.type = CORESIGHT_DEV_TYPE_SINK; |
| desc.subtype.sink_subtype = CORESIGHT_DEV_SUBTYPE_SINK_PERCPU_SYSMEM; |
| desc.ops = &arm_trbe_cs_ops; |
| desc.pdata = dev_get_platdata(dev); |
| desc.groups = arm_trbe_groups; |
| desc.dev = dev; |
| trbe_csdev = coresight_register(&desc); |
| if (IS_ERR(trbe_csdev)) |
| goto cpu_clear; |
| |
| dev_set_drvdata(&trbe_csdev->dev, cpudata); |
| coresight_set_percpu_sink(cpu, trbe_csdev); |
| return; |
| cpu_clear: |
| cpumask_clear_cpu(cpu, &drvdata->supported_cpus); |
| } |
| |
| static void arm_trbe_probe_cpu(void *info) |
| { |
| struct trbe_drvdata *drvdata = info; |
| int cpu = smp_processor_id(); |
| struct trbe_cpudata *cpudata = per_cpu_ptr(drvdata->cpudata, cpu); |
| u64 trbidr; |
| |
| if (WARN_ON(!cpudata)) |
| goto cpu_clear; |
| |
| if (!is_trbe_available()) { |
| pr_err("TRBE is not implemented on cpu %d\n", cpu); |
| goto cpu_clear; |
| } |
| |
| trbidr = read_sysreg_s(SYS_TRBIDR_EL1); |
| if (!is_trbe_programmable(trbidr)) { |
| pr_err("TRBE is owned in higher exception level on cpu %d\n", cpu); |
| goto cpu_clear; |
| } |
| |
| cpudata->trbe_align = 1ULL << get_trbe_address_align(trbidr); |
| if (cpudata->trbe_align > SZ_2K) { |
| pr_err("Unsupported alignment on cpu %d\n", cpu); |
| goto cpu_clear; |
| } |
| cpudata->trbe_flag = get_trbe_flag_update(trbidr); |
| cpudata->cpu = cpu; |
| cpudata->drvdata = drvdata; |
| return; |
| cpu_clear: |
| cpumask_clear_cpu(cpu, &drvdata->supported_cpus); |
| } |
| |
| static void arm_trbe_remove_coresight_cpu(void *info) |
| { |
| int cpu = smp_processor_id(); |
| struct trbe_drvdata *drvdata = info; |
| struct trbe_cpudata *cpudata = per_cpu_ptr(drvdata->cpudata, cpu); |
| struct coresight_device *trbe_csdev = coresight_get_percpu_sink(cpu); |
| |
| disable_percpu_irq(drvdata->irq); |
| trbe_reset_local(); |
| if (trbe_csdev) { |
| coresight_unregister(trbe_csdev); |
| cpudata->drvdata = NULL; |
| coresight_set_percpu_sink(cpu, NULL); |
| } |
| } |
| |
| static int arm_trbe_probe_coresight(struct trbe_drvdata *drvdata) |
| { |
| int cpu; |
| |
| drvdata->cpudata = alloc_percpu(typeof(*drvdata->cpudata)); |
| if (!drvdata->cpudata) |
| return -ENOMEM; |
| |
| for_each_cpu(cpu, &drvdata->supported_cpus) { |
| smp_call_function_single(cpu, arm_trbe_probe_cpu, drvdata, 1); |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) |
| arm_trbe_register_coresight_cpu(drvdata, cpu); |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) |
| smp_call_function_single(cpu, arm_trbe_enable_cpu, drvdata, 1); |
| } |
| return 0; |
| } |
| |
| static int arm_trbe_remove_coresight(struct trbe_drvdata *drvdata) |
| { |
| int cpu; |
| |
| for_each_cpu(cpu, &drvdata->supported_cpus) |
| smp_call_function_single(cpu, arm_trbe_remove_coresight_cpu, drvdata, 1); |
| free_percpu(drvdata->cpudata); |
| return 0; |
| } |
| |
| static int arm_trbe_cpu_startup(unsigned int cpu, struct hlist_node *node) |
| { |
| struct trbe_drvdata *drvdata = hlist_entry_safe(node, struct trbe_drvdata, hotplug_node); |
| |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) { |
| |
| /* |
| * If this CPU was not probed for TRBE, |
| * initialize it now. |
| */ |
| if (!coresight_get_percpu_sink(cpu)) { |
| arm_trbe_probe_cpu(drvdata); |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) |
| arm_trbe_register_coresight_cpu(drvdata, cpu); |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) |
| arm_trbe_enable_cpu(drvdata); |
| } else { |
| arm_trbe_enable_cpu(drvdata); |
| } |
| } |
| return 0; |
| } |
| |
| static int arm_trbe_cpu_teardown(unsigned int cpu, struct hlist_node *node) |
| { |
| struct trbe_drvdata *drvdata = hlist_entry_safe(node, struct trbe_drvdata, hotplug_node); |
| |
| if (cpumask_test_cpu(cpu, &drvdata->supported_cpus)) { |
| disable_percpu_irq(drvdata->irq); |
| trbe_reset_local(); |
| } |
| return 0; |
| } |
| |
| static int arm_trbe_probe_cpuhp(struct trbe_drvdata *drvdata) |
| { |
| enum cpuhp_state trbe_online; |
| int ret; |
| |
| trbe_online = cpuhp_setup_state_multi(CPUHP_AP_ONLINE_DYN, DRVNAME, |
| arm_trbe_cpu_startup, arm_trbe_cpu_teardown); |
| if (trbe_online < 0) |
| return trbe_online; |
| |
| ret = cpuhp_state_add_instance(trbe_online, &drvdata->hotplug_node); |
| if (ret) { |
| cpuhp_remove_multi_state(trbe_online); |
| return ret; |
| } |
| drvdata->trbe_online = trbe_online; |
| return 0; |
| } |
| |
| static void arm_trbe_remove_cpuhp(struct trbe_drvdata *drvdata) |
| { |
| cpuhp_remove_multi_state(drvdata->trbe_online); |
| } |
| |
| static int arm_trbe_probe_irq(struct platform_device *pdev, |
| struct trbe_drvdata *drvdata) |
| { |
| int ret; |
| |
| drvdata->irq = platform_get_irq(pdev, 0); |
| if (drvdata->irq < 0) { |
| pr_err("IRQ not found for the platform device\n"); |
| return drvdata->irq; |
| } |
| |
| if (!irq_is_percpu(drvdata->irq)) { |
| pr_err("IRQ is not a PPI\n"); |
| return -EINVAL; |
| } |
| |
| if (irq_get_percpu_devid_partition(drvdata->irq, &drvdata->supported_cpus)) |
| return -EINVAL; |
| |
| drvdata->handle = alloc_percpu(struct perf_output_handle *); |
| if (!drvdata->handle) |
| return -ENOMEM; |
| |
| ret = request_percpu_irq(drvdata->irq, arm_trbe_irq_handler, DRVNAME, drvdata->handle); |
| if (ret) { |
| free_percpu(drvdata->handle); |
| return ret; |
| } |
| return 0; |
| } |
| |
| static void arm_trbe_remove_irq(struct trbe_drvdata *drvdata) |
| { |
| free_percpu_irq(drvdata->irq, drvdata->handle); |
| free_percpu(drvdata->handle); |
| } |
| |
| static int arm_trbe_device_probe(struct platform_device *pdev) |
| { |
| struct coresight_platform_data *pdata; |
| struct trbe_drvdata *drvdata; |
| struct device *dev = &pdev->dev; |
| int ret; |
| |
| drvdata = devm_kzalloc(dev, sizeof(*drvdata), GFP_KERNEL); |
| if (!drvdata) |
| return -ENOMEM; |
| |
| pdata = coresight_get_platform_data(dev); |
| if (IS_ERR(pdata)) |
| return PTR_ERR(pdata); |
| |
| dev_set_drvdata(dev, drvdata); |
| dev->platform_data = pdata; |
| drvdata->pdev = pdev; |
| ret = arm_trbe_probe_irq(pdev, drvdata); |
| if (ret) |
| return ret; |
| |
| ret = arm_trbe_probe_coresight(drvdata); |
| if (ret) |
| goto probe_failed; |
| |
| ret = arm_trbe_probe_cpuhp(drvdata); |
| if (ret) |
| goto cpuhp_failed; |
| |
| return 0; |
| cpuhp_failed: |
| arm_trbe_remove_coresight(drvdata); |
| probe_failed: |
| arm_trbe_remove_irq(drvdata); |
| return ret; |
| } |
| |
| static int arm_trbe_device_remove(struct platform_device *pdev) |
| { |
| struct trbe_drvdata *drvdata = platform_get_drvdata(pdev); |
| |
| arm_trbe_remove_cpuhp(drvdata); |
| arm_trbe_remove_coresight(drvdata); |
| arm_trbe_remove_irq(drvdata); |
| return 0; |
| } |
| |
| static const struct of_device_id arm_trbe_of_match[] = { |
| { .compatible = "arm,trace-buffer-extension"}, |
| {}, |
| }; |
| MODULE_DEVICE_TABLE(of, arm_trbe_of_match); |
| |
| static struct platform_driver arm_trbe_driver = { |
| .driver = { |
| .name = DRVNAME, |
| .of_match_table = of_match_ptr(arm_trbe_of_match), |
| .suppress_bind_attrs = true, |
| }, |
| .probe = arm_trbe_device_probe, |
| .remove = arm_trbe_device_remove, |
| }; |
| |
| static int __init arm_trbe_init(void) |
| { |
| int ret; |
| |
| if (arm64_kernel_unmapped_at_el0()) { |
| pr_err("TRBE wouldn't work if kernel gets unmapped at EL0\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| ret = platform_driver_register(&arm_trbe_driver); |
| if (!ret) |
| return 0; |
| |
| pr_err("Error registering %s platform driver\n", DRVNAME); |
| return ret; |
| } |
| |
| static void __exit arm_trbe_exit(void) |
| { |
| platform_driver_unregister(&arm_trbe_driver); |
| } |
| module_init(arm_trbe_init); |
| module_exit(arm_trbe_exit); |
| |
| MODULE_AUTHOR("Anshuman Khandual <anshuman.khandual@arm.com>"); |
| MODULE_DESCRIPTION("Arm Trace Buffer Extension (TRBE) driver"); |
| MODULE_LICENSE("GPL v2"); |