| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * UFS Host driver for Synopsys Designware Core |
| * |
| * Copyright (C) 2015-2016 Synopsys, Inc. (www.synopsys.com) |
| * |
| * Authors: Joao Pinto <jpinto@synopsys.com> |
| */ |
| |
| #include "ufshcd.h" |
| #include "unipro.h" |
| |
| #include "ufshcd-dwc.h" |
| #include "ufshci-dwc.h" |
| |
| int ufshcd_dwc_dme_set_attrs(struct ufs_hba *hba, |
| const struct ufshcd_dme_attr_val *v, int n) |
| { |
| int ret = 0; |
| int attr_node = 0; |
| |
| for (attr_node = 0; attr_node < n; attr_node++) { |
| ret = ufshcd_dme_set_attr(hba, v[attr_node].attr_sel, |
| ATTR_SET_NOR, v[attr_node].mib_val, v[attr_node].peer); |
| |
| if (ret) |
| return ret; |
| } |
| |
| return 0; |
| } |
| EXPORT_SYMBOL(ufshcd_dwc_dme_set_attrs); |
| |
| /** |
| * ufshcd_dwc_program_clk_div() |
| * This function programs the clk divider value. This value is needed to |
| * provide 1 microsecond tick to unipro layer. |
| * @hba: Private Structure pointer |
| * @divider_val: clock divider value to be programmed |
| * |
| */ |
| static void ufshcd_dwc_program_clk_div(struct ufs_hba *hba, u32 divider_val) |
| { |
| ufshcd_writel(hba, divider_val, DWC_UFS_REG_HCLKDIV); |
| } |
| |
| /** |
| * ufshcd_dwc_link_is_up() |
| * Check if link is up |
| * @hba: private structure pointer |
| * |
| * Returns 0 on success, non-zero value on failure |
| */ |
| static int ufshcd_dwc_link_is_up(struct ufs_hba *hba) |
| { |
| int dme_result = 0; |
| |
| ufshcd_dme_get(hba, UIC_ARG_MIB(VS_POWERSTATE), &dme_result); |
| |
| if (dme_result == UFSHCD_LINK_IS_UP) { |
| ufshcd_set_link_active(hba); |
| return 0; |
| } |
| |
| return 1; |
| } |
| |
| /** |
| * ufshcd_dwc_connection_setup() |
| * This function configures both the local side (host) and the peer side |
| * (device) unipro attributes to establish the connection to application/ |
| * cport. |
| * This function is not required if the hardware is properly configured to |
| * have this connection setup on reset. But invoking this function does no |
| * harm and should be fine even working with any ufs device. |
| * |
| * @hba: pointer to drivers private data |
| * |
| * Returns 0 on success non-zero value on failure |
| */ |
| static int ufshcd_dwc_connection_setup(struct ufs_hba *hba) |
| { |
| static const struct ufshcd_dme_attr_val setup_attrs[] = { |
| { UIC_ARG_MIB(T_CONNECTIONSTATE), 0, DME_LOCAL }, |
| { UIC_ARG_MIB(N_DEVICEID), 0, DME_LOCAL }, |
| { UIC_ARG_MIB(N_DEVICEID_VALID), 0, DME_LOCAL }, |
| { UIC_ARG_MIB(T_PEERDEVICEID), 1, DME_LOCAL }, |
| { UIC_ARG_MIB(T_PEERCPORTID), 0, DME_LOCAL }, |
| { UIC_ARG_MIB(T_TRAFFICCLASS), 0, DME_LOCAL }, |
| { UIC_ARG_MIB(T_CPORTFLAGS), 0x6, DME_LOCAL }, |
| { UIC_ARG_MIB(T_CPORTMODE), 1, DME_LOCAL }, |
| { UIC_ARG_MIB(T_CONNECTIONSTATE), 1, DME_LOCAL }, |
| { UIC_ARG_MIB(T_CONNECTIONSTATE), 0, DME_PEER }, |
| { UIC_ARG_MIB(N_DEVICEID), 1, DME_PEER }, |
| { UIC_ARG_MIB(N_DEVICEID_VALID), 1, DME_PEER }, |
| { UIC_ARG_MIB(T_PEERDEVICEID), 1, DME_PEER }, |
| { UIC_ARG_MIB(T_PEERCPORTID), 0, DME_PEER }, |
| { UIC_ARG_MIB(T_TRAFFICCLASS), 0, DME_PEER }, |
| { UIC_ARG_MIB(T_CPORTFLAGS), 0x6, DME_PEER }, |
| { UIC_ARG_MIB(T_CPORTMODE), 1, DME_PEER }, |
| { UIC_ARG_MIB(T_CONNECTIONSTATE), 1, DME_PEER } |
| }; |
| |
| return ufshcd_dwc_dme_set_attrs(hba, setup_attrs, ARRAY_SIZE(setup_attrs)); |
| } |
| |
| /** |
| * ufshcd_dwc_link_startup_notify() |
| * UFS Host DWC specific link startup sequence |
| * @hba: private structure pointer |
| * @status: Callback notify status |
| * |
| * Returns 0 on success, non-zero value on failure |
| */ |
| int ufshcd_dwc_link_startup_notify(struct ufs_hba *hba, |
| enum ufs_notify_change_status status) |
| { |
| int err = 0; |
| |
| if (status == PRE_CHANGE) { |
| ufshcd_dwc_program_clk_div(hba, DWC_UFS_REG_HCLKDIV_DIV_125); |
| |
| if (hba->vops->phy_initialization) { |
| err = hba->vops->phy_initialization(hba); |
| if (err) { |
| dev_err(hba->dev, "Phy setup failed (%d)\n", |
| err); |
| goto out; |
| } |
| } |
| } else { /* POST_CHANGE */ |
| err = ufshcd_dwc_link_is_up(hba); |
| if (err) { |
| dev_err(hba->dev, "Link is not up\n"); |
| goto out; |
| } |
| |
| err = ufshcd_dwc_connection_setup(hba); |
| if (err) |
| dev_err(hba->dev, "Connection setup failed (%d)\n", |
| err); |
| } |
| |
| out: |
| return err; |
| } |
| EXPORT_SYMBOL(ufshcd_dwc_link_startup_notify); |
| |
| MODULE_AUTHOR("Joao Pinto <Joao.Pinto@synopsys.com>"); |
| MODULE_DESCRIPTION("UFS Host driver for Synopsys Designware Core"); |
| MODULE_LICENSE("Dual BSD/GPL"); |