| /* |
| * Cypress APA trackpad with I2C interface |
| * |
| * Author: Dudley Du <dudl@cypress.com> |
| * Further cleanup and restructuring by: |
| * Daniel Kurtz <djkurtz@chromium.org> |
| * Benson Leung <bleung@chromium.org> |
| * |
| * Copyright (C) 2011-2015 Cypress Semiconductor, Inc. |
| * Copyright (C) 2011-2012 Google, Inc. |
| * |
| * This file is subject to the terms and conditions of the GNU General Public |
| * License. See the file COPYING in the main directory of this archive for |
| * more details. |
| */ |
| |
| #include <linux/delay.h> |
| #include <linux/i2c.h> |
| #include <linux/input.h> |
| #include <linux/input/mt.h> |
| #include <linux/module.h> |
| #include <linux/slab.h> |
| #include <asm/unaligned.h> |
| #include "cyapa.h" |
| |
| |
| #define GEN3_MAX_FINGERS 5 |
| #define GEN3_FINGER_NUM(x) (((x) >> 4) & 0x07) |
| |
| #define BLK_HEAD_BYTES 32 |
| |
| /* Macro for register map group offset. */ |
| #define PRODUCT_ID_SIZE 16 |
| #define QUERY_DATA_SIZE 27 |
| #define REG_PROTOCOL_GEN_QUERY_OFFSET 20 |
| |
| #define REG_OFFSET_DATA_BASE 0x0000 |
| #define REG_OFFSET_COMMAND_BASE 0x0028 |
| #define REG_OFFSET_QUERY_BASE 0x002a |
| |
| #define CYAPA_OFFSET_SOFT_RESET REG_OFFSET_COMMAND_BASE |
| #define OP_RECALIBRATION_MASK 0x80 |
| #define OP_REPORT_BASELINE_MASK 0x40 |
| #define REG_OFFSET_MAX_BASELINE 0x0026 |
| #define REG_OFFSET_MIN_BASELINE 0x0027 |
| |
| #define REG_OFFSET_POWER_MODE (REG_OFFSET_COMMAND_BASE + 1) |
| #define SET_POWER_MODE_DELAY 10000 /* Unit: us */ |
| #define SET_POWER_MODE_TRIES 5 |
| |
| #define GEN3_BL_CMD_CHECKSUM_SEED 0xff |
| #define GEN3_BL_CMD_INITIATE_BL 0x38 |
| #define GEN3_BL_CMD_WRITE_BLOCK 0x39 |
| #define GEN3_BL_CMD_VERIFY_BLOCK 0x3a |
| #define GEN3_BL_CMD_TERMINATE_BL 0x3b |
| #define GEN3_BL_CMD_LAUNCH_APP 0xa5 |
| |
| /* |
| * CYAPA trackpad device states. |
| * Used in register 0x00, bit1-0, DeviceStatus field. |
| * Other values indicate device is in an abnormal state and must be reset. |
| */ |
| #define CYAPA_DEV_NORMAL 0x03 |
| #define CYAPA_DEV_BUSY 0x01 |
| |
| #define CYAPA_FW_BLOCK_SIZE 64 |
| #define CYAPA_FW_READ_SIZE 16 |
| #define CYAPA_FW_HDR_START 0x0780 |
| #define CYAPA_FW_HDR_BLOCK_COUNT 2 |
| #define CYAPA_FW_HDR_BLOCK_START (CYAPA_FW_HDR_START / CYAPA_FW_BLOCK_SIZE) |
| #define CYAPA_FW_HDR_SIZE (CYAPA_FW_HDR_BLOCK_COUNT * \ |
| CYAPA_FW_BLOCK_SIZE) |
| #define CYAPA_FW_DATA_START 0x0800 |
| #define CYAPA_FW_DATA_BLOCK_COUNT 480 |
| #define CYAPA_FW_DATA_BLOCK_START (CYAPA_FW_DATA_START / CYAPA_FW_BLOCK_SIZE) |
| #define CYAPA_FW_DATA_SIZE (CYAPA_FW_DATA_BLOCK_COUNT * \ |
| CYAPA_FW_BLOCK_SIZE) |
| #define CYAPA_FW_SIZE (CYAPA_FW_HDR_SIZE + CYAPA_FW_DATA_SIZE) |
| #define CYAPA_CMD_LEN 16 |
| |
| #define GEN3_BL_IDLE_FW_MAJ_VER_OFFSET 0x0b |
| #define GEN3_BL_IDLE_FW_MIN_VER_OFFSET (GEN3_BL_IDLE_FW_MAJ_VER_OFFSET + 1) |
| |
| |
| struct cyapa_touch { |
| /* |
| * high bits or x/y position value |
| * bit 7 - 4: high 4 bits of x position value |
| * bit 3 - 0: high 4 bits of y position value |
| */ |
| u8 xy_hi; |
| u8 x_lo; /* low 8 bits of x position value. */ |
| u8 y_lo; /* low 8 bits of y position value. */ |
| u8 pressure; |
| /* id range is 1 - 15. It is incremented with every new touch. */ |
| u8 id; |
| } __packed; |
| |
| struct cyapa_reg_data { |
| /* |
| * bit 0 - 1: device status |
| * bit 3 - 2: power mode |
| * bit 6 - 4: reserved |
| * bit 7: interrupt valid bit |
| */ |
| u8 device_status; |
| /* |
| * bit 7 - 4: number of fingers currently touching pad |
| * bit 3: valid data check bit |
| * bit 2: middle mechanism button state if exists |
| * bit 1: right mechanism button state if exists |
| * bit 0: left mechanism button state if exists |
| */ |
| u8 finger_btn; |
| /* CYAPA reports up to 5 touches per packet. */ |
| struct cyapa_touch touches[5]; |
| } __packed; |
| |
| struct gen3_write_block_cmd { |
| u8 checksum_seed; /* Always be 0xff */ |
| u8 cmd_code; /* command code: 0x39 */ |
| u8 key[8]; /* 8-byte security key */ |
| __be16 block_num; |
| u8 block_data[CYAPA_FW_BLOCK_SIZE]; |
| u8 block_checksum; /* Calculated using bytes 12 - 75 */ |
| u8 cmd_checksum; /* Calculated using bytes 0-76 */ |
| } __packed; |
| |
| static const u8 security_key[] = { |
| 0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07 }; |
| static const u8 bl_activate[] = { 0x00, 0xff, 0x38, 0x00, 0x01, 0x02, 0x03, |
| 0x04, 0x05, 0x06, 0x07 }; |
| static const u8 bl_deactivate[] = { 0x00, 0xff, 0x3b, 0x00, 0x01, 0x02, 0x03, |
| 0x04, 0x05, 0x06, 0x07 }; |
| static const u8 bl_exit[] = { 0x00, 0xff, 0xa5, 0x00, 0x01, 0x02, 0x03, 0x04, |
| 0x05, 0x06, 0x07 }; |
| |
| |
| /* for byte read/write command */ |
| #define CMD_RESET 0 |
| #define CMD_POWER_MODE 1 |
| #define CMD_DEV_STATUS 2 |
| #define CMD_REPORT_MAX_BASELINE 3 |
| #define CMD_REPORT_MIN_BASELINE 4 |
| #define SMBUS_BYTE_CMD(cmd) (((cmd) & 0x3f) << 1) |
| #define CYAPA_SMBUS_RESET SMBUS_BYTE_CMD(CMD_RESET) |
| #define CYAPA_SMBUS_POWER_MODE SMBUS_BYTE_CMD(CMD_POWER_MODE) |
| #define CYAPA_SMBUS_DEV_STATUS SMBUS_BYTE_CMD(CMD_DEV_STATUS) |
| #define CYAPA_SMBUS_MAX_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MAX_BASELINE) |
| #define CYAPA_SMBUS_MIN_BASELINE SMBUS_BYTE_CMD(CMD_REPORT_MIN_BASELINE) |
| |
| /* for group registers read/write command */ |
| #define REG_GROUP_DATA 0 |
| #define REG_GROUP_CMD 2 |
| #define REG_GROUP_QUERY 3 |
| #define SMBUS_GROUP_CMD(grp) (0x80 | (((grp) & 0x07) << 3)) |
| #define CYAPA_SMBUS_GROUP_DATA SMBUS_GROUP_CMD(REG_GROUP_DATA) |
| #define CYAPA_SMBUS_GROUP_CMD SMBUS_GROUP_CMD(REG_GROUP_CMD) |
| #define CYAPA_SMBUS_GROUP_QUERY SMBUS_GROUP_CMD(REG_GROUP_QUERY) |
| |
| /* for register block read/write command */ |
| #define CMD_BL_STATUS 0 |
| #define CMD_BL_HEAD 1 |
| #define CMD_BL_CMD 2 |
| #define CMD_BL_DATA 3 |
| #define CMD_BL_ALL 4 |
| #define CMD_BLK_PRODUCT_ID 5 |
| #define CMD_BLK_HEAD 6 |
| #define SMBUS_BLOCK_CMD(cmd) (0xc0 | (((cmd) & 0x1f) << 1)) |
| |
| /* register block read/write command in bootloader mode */ |
| #define CYAPA_SMBUS_BL_STATUS SMBUS_BLOCK_CMD(CMD_BL_STATUS) |
| #define CYAPA_SMBUS_BL_HEAD SMBUS_BLOCK_CMD(CMD_BL_HEAD) |
| #define CYAPA_SMBUS_BL_CMD SMBUS_BLOCK_CMD(CMD_BL_CMD) |
| #define CYAPA_SMBUS_BL_DATA SMBUS_BLOCK_CMD(CMD_BL_DATA) |
| #define CYAPA_SMBUS_BL_ALL SMBUS_BLOCK_CMD(CMD_BL_ALL) |
| |
| /* register block read/write command in operational mode */ |
| #define CYAPA_SMBUS_BLK_PRODUCT_ID SMBUS_BLOCK_CMD(CMD_BLK_PRODUCT_ID) |
| #define CYAPA_SMBUS_BLK_HEAD SMBUS_BLOCK_CMD(CMD_BLK_HEAD) |
| |
| struct cyapa_cmd_len { |
| u8 cmd; |
| u8 len; |
| }; |
| |
| /* maps generic CYAPA_CMD_* code to the I2C equivalent */ |
| static const struct cyapa_cmd_len cyapa_i2c_cmds[] = { |
| { CYAPA_OFFSET_SOFT_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */ |
| { REG_OFFSET_COMMAND_BASE + 1, 1 }, /* CYAPA_CMD_POWER_MODE */ |
| { REG_OFFSET_DATA_BASE, 1 }, /* CYAPA_CMD_DEV_STATUS */ |
| { REG_OFFSET_DATA_BASE, sizeof(struct cyapa_reg_data) }, |
| /* CYAPA_CMD_GROUP_DATA */ |
| { REG_OFFSET_COMMAND_BASE, 0 }, /* CYAPA_CMD_GROUP_CMD */ |
| { REG_OFFSET_QUERY_BASE, QUERY_DATA_SIZE }, /* CYAPA_CMD_GROUP_QUERY */ |
| { BL_HEAD_OFFSET, 3 }, /* CYAPA_CMD_BL_STATUS */ |
| { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_HEAD */ |
| { BL_HEAD_OFFSET, 16 }, /* CYAPA_CMD_BL_CMD */ |
| { BL_DATA_OFFSET, 16 }, /* CYAPA_CMD_BL_DATA */ |
| { BL_HEAD_OFFSET, 32 }, /* CYAPA_CMD_BL_ALL */ |
| { REG_OFFSET_QUERY_BASE, PRODUCT_ID_SIZE }, |
| /* CYAPA_CMD_BLK_PRODUCT_ID */ |
| { REG_OFFSET_DATA_BASE, 32 }, /* CYAPA_CMD_BLK_HEAD */ |
| { REG_OFFSET_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */ |
| { REG_OFFSET_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */ |
| }; |
| |
| static const struct cyapa_cmd_len cyapa_smbus_cmds[] = { |
| { CYAPA_SMBUS_RESET, 1 }, /* CYAPA_CMD_SOFT_RESET */ |
| { CYAPA_SMBUS_POWER_MODE, 1 }, /* CYAPA_CMD_POWER_MODE */ |
| { CYAPA_SMBUS_DEV_STATUS, 1 }, /* CYAPA_CMD_DEV_STATUS */ |
| { CYAPA_SMBUS_GROUP_DATA, sizeof(struct cyapa_reg_data) }, |
| /* CYAPA_CMD_GROUP_DATA */ |
| { CYAPA_SMBUS_GROUP_CMD, 2 }, /* CYAPA_CMD_GROUP_CMD */ |
| { CYAPA_SMBUS_GROUP_QUERY, QUERY_DATA_SIZE }, |
| /* CYAPA_CMD_GROUP_QUERY */ |
| { CYAPA_SMBUS_BL_STATUS, 3 }, /* CYAPA_CMD_BL_STATUS */ |
| { CYAPA_SMBUS_BL_HEAD, 16 }, /* CYAPA_CMD_BL_HEAD */ |
| { CYAPA_SMBUS_BL_CMD, 16 }, /* CYAPA_CMD_BL_CMD */ |
| { CYAPA_SMBUS_BL_DATA, 16 }, /* CYAPA_CMD_BL_DATA */ |
| { CYAPA_SMBUS_BL_ALL, 32 }, /* CYAPA_CMD_BL_ALL */ |
| { CYAPA_SMBUS_BLK_PRODUCT_ID, PRODUCT_ID_SIZE }, |
| /* CYAPA_CMD_BLK_PRODUCT_ID */ |
| { CYAPA_SMBUS_BLK_HEAD, 16 }, /* CYAPA_CMD_BLK_HEAD */ |
| { CYAPA_SMBUS_MAX_BASELINE, 1 }, /* CYAPA_CMD_MAX_BASELINE */ |
| { CYAPA_SMBUS_MIN_BASELINE, 1 }, /* CYAPA_CMD_MIN_BASELINE */ |
| }; |
| |
| static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa); |
| |
| /* |
| * cyapa_smbus_read_block - perform smbus block read command |
| * @cyapa - private data structure of the driver |
| * @cmd - the properly encoded smbus command |
| * @len - expected length of smbus command result |
| * @values - buffer to store smbus command result |
| * |
| * Returns negative errno, else the number of bytes written. |
| * |
| * Note: |
| * In trackpad device, the memory block allocated for I2C register map |
| * is 256 bytes, so the max read block for I2C bus is 256 bytes. |
| */ |
| ssize_t cyapa_smbus_read_block(struct cyapa *cyapa, u8 cmd, size_t len, |
| u8 *values) |
| { |
| ssize_t ret; |
| u8 index; |
| u8 smbus_cmd; |
| u8 *buf; |
| struct i2c_client *client = cyapa->client; |
| |
| if (!(SMBUS_BYTE_BLOCK_CMD_MASK & cmd)) |
| return -EINVAL; |
| |
| if (SMBUS_GROUP_BLOCK_CMD_MASK & cmd) { |
| /* read specific block registers command. */ |
| smbus_cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ); |
| ret = i2c_smbus_read_block_data(client, smbus_cmd, values); |
| goto out; |
| } |
| |
| ret = 0; |
| for (index = 0; index * I2C_SMBUS_BLOCK_MAX < len; index++) { |
| smbus_cmd = SMBUS_ENCODE_IDX(cmd, index); |
| smbus_cmd = SMBUS_ENCODE_RW(smbus_cmd, SMBUS_READ); |
| buf = values + I2C_SMBUS_BLOCK_MAX * index; |
| ret = i2c_smbus_read_block_data(client, smbus_cmd, buf); |
| if (ret < 0) |
| goto out; |
| } |
| |
| out: |
| return ret > 0 ? len : ret; |
| } |
| |
| static s32 cyapa_read_byte(struct cyapa *cyapa, u8 cmd_idx) |
| { |
| u8 cmd; |
| |
| if (cyapa->smbus) { |
| cmd = cyapa_smbus_cmds[cmd_idx].cmd; |
| cmd = SMBUS_ENCODE_RW(cmd, SMBUS_READ); |
| } else { |
| cmd = cyapa_i2c_cmds[cmd_idx].cmd; |
| } |
| return i2c_smbus_read_byte_data(cyapa->client, cmd); |
| } |
| |
| static s32 cyapa_write_byte(struct cyapa *cyapa, u8 cmd_idx, u8 value) |
| { |
| u8 cmd; |
| |
| if (cyapa->smbus) { |
| cmd = cyapa_smbus_cmds[cmd_idx].cmd; |
| cmd = SMBUS_ENCODE_RW(cmd, SMBUS_WRITE); |
| } else { |
| cmd = cyapa_i2c_cmds[cmd_idx].cmd; |
| } |
| return i2c_smbus_write_byte_data(cyapa->client, cmd, value); |
| } |
| |
| ssize_t cyapa_i2c_reg_read_block(struct cyapa *cyapa, u8 reg, size_t len, |
| u8 *values) |
| { |
| return i2c_smbus_read_i2c_block_data(cyapa->client, reg, len, values); |
| } |
| |
| static ssize_t cyapa_i2c_reg_write_block(struct cyapa *cyapa, u8 reg, |
| size_t len, const u8 *values) |
| { |
| return i2c_smbus_write_i2c_block_data(cyapa->client, reg, len, values); |
| } |
| |
| ssize_t cyapa_read_block(struct cyapa *cyapa, u8 cmd_idx, u8 *values) |
| { |
| u8 cmd; |
| size_t len; |
| |
| if (cyapa->smbus) { |
| cmd = cyapa_smbus_cmds[cmd_idx].cmd; |
| len = cyapa_smbus_cmds[cmd_idx].len; |
| return cyapa_smbus_read_block(cyapa, cmd, len, values); |
| } |
| cmd = cyapa_i2c_cmds[cmd_idx].cmd; |
| len = cyapa_i2c_cmds[cmd_idx].len; |
| return cyapa_i2c_reg_read_block(cyapa, cmd, len, values); |
| } |
| |
| /* |
| * Determine the Gen3 trackpad device's current operating state. |
| * |
| */ |
| static int cyapa_gen3_state_parse(struct cyapa *cyapa, u8 *reg_data, int len) |
| { |
| cyapa->state = CYAPA_STATE_NO_DEVICE; |
| |
| /* Parse based on Gen3 characteristic registers and bits */ |
| if (reg_data[REG_BL_FILE] == BL_FILE && |
| reg_data[REG_BL_ERROR] == BL_ERROR_NO_ERR_IDLE && |
| (reg_data[REG_BL_STATUS] == |
| (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID) || |
| reg_data[REG_BL_STATUS] == BL_STATUS_RUNNING)) { |
| /* |
| * Normal state after power on or reset, |
| * REG_BL_STATUS == 0x11, firmware image checksum is valid. |
| * REG_BL_STATUS == 0x10, firmware image checksum is invalid. |
| */ |
| cyapa->gen = CYAPA_GEN3; |
| cyapa->state = CYAPA_STATE_BL_IDLE; |
| } else if (reg_data[REG_BL_FILE] == BL_FILE && |
| (reg_data[REG_BL_STATUS] & BL_STATUS_RUNNING) == |
| BL_STATUS_RUNNING) { |
| cyapa->gen = CYAPA_GEN3; |
| if (reg_data[REG_BL_STATUS] & BL_STATUS_BUSY) { |
| cyapa->state = CYAPA_STATE_BL_BUSY; |
| } else { |
| if ((reg_data[REG_BL_ERROR] & BL_ERROR_BOOTLOADING) == |
| BL_ERROR_BOOTLOADING) |
| cyapa->state = CYAPA_STATE_BL_ACTIVE; |
| else |
| cyapa->state = CYAPA_STATE_BL_IDLE; |
| } |
| } else if ((reg_data[REG_OP_STATUS] & OP_STATUS_SRC) && |
| (reg_data[REG_OP_DATA1] & OP_DATA_VALID)) { |
| /* |
| * Normal state when running in operational mode, |
| * may also not in full power state or |
| * busying in command process. |
| */ |
| if (GEN3_FINGER_NUM(reg_data[REG_OP_DATA1]) <= |
| GEN3_MAX_FINGERS) { |
| /* Finger number data is valid. */ |
| cyapa->gen = CYAPA_GEN3; |
| cyapa->state = CYAPA_STATE_OP; |
| } |
| } else if (reg_data[REG_OP_STATUS] == 0x0C && |
| reg_data[REG_OP_DATA1] == 0x08) { |
| /* Op state when first two registers overwritten with 0x00 */ |
| cyapa->gen = CYAPA_GEN3; |
| cyapa->state = CYAPA_STATE_OP; |
| } else if (reg_data[REG_BL_STATUS] & |
| (BL_STATUS_RUNNING | BL_STATUS_BUSY)) { |
| cyapa->gen = CYAPA_GEN3; |
| cyapa->state = CYAPA_STATE_BL_BUSY; |
| } |
| |
| if (cyapa->gen == CYAPA_GEN3 && (cyapa->state == CYAPA_STATE_OP || |
| cyapa->state == CYAPA_STATE_BL_IDLE || |
| cyapa->state == CYAPA_STATE_BL_ACTIVE || |
| cyapa->state == CYAPA_STATE_BL_BUSY)) |
| return 0; |
| |
| return -EAGAIN; |
| } |
| |
| /* |
| * Enter bootloader by soft resetting the device. |
| * |
| * If device is already in the bootloader, the function just returns. |
| * Otherwise, reset the device; after reset, device enters bootloader idle |
| * state immediately. |
| * |
| * Returns: |
| * 0 on success |
| * -EAGAIN device was reset, but is not now in bootloader idle state |
| * < 0 if the device never responds within the timeout |
| */ |
| static int cyapa_gen3_bl_enter(struct cyapa *cyapa) |
| { |
| int error; |
| int waiting_time; |
| |
| error = cyapa_poll_state(cyapa, 500); |
| if (error) |
| return error; |
| if (cyapa->state == CYAPA_STATE_BL_IDLE) { |
| /* Already in BL_IDLE. Skipping reset. */ |
| return 0; |
| } |
| |
| if (cyapa->state != CYAPA_STATE_OP) |
| return -EAGAIN; |
| |
| cyapa->operational = false; |
| cyapa->state = CYAPA_STATE_NO_DEVICE; |
| error = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, 0x01); |
| if (error) |
| return -EIO; |
| |
| usleep_range(25000, 50000); |
| waiting_time = 2000; /* For some shipset, max waiting time is 1~2s. */ |
| do { |
| error = cyapa_poll_state(cyapa, 500); |
| if (error) { |
| if (error == -ETIMEDOUT) { |
| waiting_time -= 500; |
| continue; |
| } |
| return error; |
| } |
| |
| if ((cyapa->state == CYAPA_STATE_BL_IDLE) && |
| !(cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG)) |
| break; |
| |
| msleep(100); |
| waiting_time -= 100; |
| } while (waiting_time > 0); |
| |
| if ((cyapa->state != CYAPA_STATE_BL_IDLE) || |
| (cyapa->status[REG_BL_STATUS] & BL_STATUS_WATCHDOG)) |
| return -EAGAIN; |
| |
| return 0; |
| } |
| |
| static int cyapa_gen3_bl_activate(struct cyapa *cyapa) |
| { |
| int error; |
| |
| error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_activate), |
| bl_activate); |
| if (error) |
| return error; |
| |
| /* Wait for bootloader to activate; takes between 2 and 12 seconds */ |
| msleep(2000); |
| error = cyapa_poll_state(cyapa, 11000); |
| if (error) |
| return error; |
| if (cyapa->state != CYAPA_STATE_BL_ACTIVE) |
| return -EAGAIN; |
| |
| return 0; |
| } |
| |
| static int cyapa_gen3_bl_deactivate(struct cyapa *cyapa) |
| { |
| int error; |
| |
| error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_deactivate), |
| bl_deactivate); |
| if (error) |
| return error; |
| |
| /* Wait for bootloader to switch to idle state; should take < 100ms */ |
| msleep(100); |
| error = cyapa_poll_state(cyapa, 500); |
| if (error) |
| return error; |
| if (cyapa->state != CYAPA_STATE_BL_IDLE) |
| return -EAGAIN; |
| return 0; |
| } |
| |
| /* |
| * Exit bootloader |
| * |
| * Send bl_exit command, then wait 50 - 100 ms to let device transition to |
| * operational mode. If this is the first time the device's firmware is |
| * running, it can take up to 2 seconds to calibrate its sensors. So, poll |
| * the device's new state for up to 2 seconds. |
| * |
| * Returns: |
| * -EIO failure while reading from device |
| * -EAGAIN device is stuck in bootloader, b/c it has invalid firmware |
| * 0 device is supported and in operational mode |
| */ |
| static int cyapa_gen3_bl_exit(struct cyapa *cyapa) |
| { |
| int error; |
| |
| error = cyapa_i2c_reg_write_block(cyapa, 0, sizeof(bl_exit), bl_exit); |
| if (error) |
| return error; |
| |
| /* |
| * Wait for bootloader to exit, and operation mode to start. |
| * Normally, this takes at least 50 ms. |
| */ |
| msleep(50); |
| /* |
| * In addition, when a device boots for the first time after being |
| * updated to new firmware, it must first calibrate its sensors, which |
| * can take up to an additional 2 seconds. If the device power is |
| * running low, this may take even longer. |
| */ |
| error = cyapa_poll_state(cyapa, 4000); |
| if (error < 0) |
| return error; |
| if (cyapa->state != CYAPA_STATE_OP) |
| return -EAGAIN; |
| |
| return 0; |
| } |
| |
| static u16 cyapa_gen3_csum(const u8 *buf, size_t count) |
| { |
| int i; |
| u16 csum = 0; |
| |
| for (i = 0; i < count; i++) |
| csum += buf[i]; |
| |
| return csum; |
| } |
| |
| /* |
| * Verify the integrity of a CYAPA firmware image file. |
| * |
| * The firmware image file is 30848 bytes, composed of 482 64-byte blocks. |
| * |
| * The first 2 blocks are the firmware header. |
| * The next 480 blocks are the firmware image. |
| * |
| * The first two bytes of the header hold the header checksum, computed by |
| * summing the other 126 bytes of the header. |
| * The last two bytes of the header hold the firmware image checksum, computed |
| * by summing the 30720 bytes of the image modulo 0xffff. |
| * |
| * Both checksums are stored little-endian. |
| */ |
| static int cyapa_gen3_check_fw(struct cyapa *cyapa, const struct firmware *fw) |
| { |
| struct device *dev = &cyapa->client->dev; |
| u16 csum; |
| u16 csum_expected; |
| |
| /* Firmware must match exact 30848 bytes = 482 64-byte blocks. */ |
| if (fw->size != CYAPA_FW_SIZE) { |
| dev_err(dev, "invalid firmware size = %zu, expected %u.\n", |
| fw->size, CYAPA_FW_SIZE); |
| return -EINVAL; |
| } |
| |
| /* Verify header block */ |
| csum_expected = (fw->data[0] << 8) | fw->data[1]; |
| csum = cyapa_gen3_csum(&fw->data[2], CYAPA_FW_HDR_SIZE - 2); |
| if (csum != csum_expected) { |
| dev_err(dev, "%s %04x, expected: %04x\n", |
| "invalid firmware header checksum = ", |
| csum, csum_expected); |
| return -EINVAL; |
| } |
| |
| /* Verify firmware image */ |
| csum_expected = (fw->data[CYAPA_FW_HDR_SIZE - 2] << 8) | |
| fw->data[CYAPA_FW_HDR_SIZE - 1]; |
| csum = cyapa_gen3_csum(&fw->data[CYAPA_FW_HDR_SIZE], |
| CYAPA_FW_DATA_SIZE); |
| if (csum != csum_expected) { |
| dev_err(dev, "%s %04x, expected: %04x\n", |
| "invalid firmware header checksum = ", |
| csum, csum_expected); |
| return -EINVAL; |
| } |
| return 0; |
| } |
| |
| /* |
| * Write a |len| byte long buffer |buf| to the device, by chopping it up into a |
| * sequence of smaller |CYAPA_CMD_LEN|-length write commands. |
| * |
| * The data bytes for a write command are prepended with the 1-byte offset |
| * of the data relative to the start of |buf|. |
| */ |
| static int cyapa_gen3_write_buffer(struct cyapa *cyapa, |
| const u8 *buf, size_t len) |
| { |
| int error; |
| size_t i; |
| unsigned char cmd[CYAPA_CMD_LEN + 1]; |
| size_t cmd_len; |
| |
| for (i = 0; i < len; i += CYAPA_CMD_LEN) { |
| const u8 *payload = &buf[i]; |
| |
| cmd_len = (len - i >= CYAPA_CMD_LEN) ? CYAPA_CMD_LEN : len - i; |
| cmd[0] = i; |
| memcpy(&cmd[1], payload, cmd_len); |
| |
| error = cyapa_i2c_reg_write_block(cyapa, 0, cmd_len + 1, cmd); |
| if (error) |
| return error; |
| } |
| return 0; |
| } |
| |
| /* |
| * A firmware block write command writes 64 bytes of data to a single flash |
| * page in the device. The 78-byte block write command has the format: |
| * <0xff> <CMD> <Key> <Start> <Data> <Data-Checksum> <CMD Checksum> |
| * |
| * <0xff> - every command starts with 0xff |
| * <CMD> - the write command value is 0x39 |
| * <Key> - write commands include an 8-byte key: { 00 01 02 03 04 05 06 07 } |
| * <Block> - Memory Block number (address / 64) (16-bit, big-endian) |
| * <Data> - 64 bytes of firmware image data |
| * <Data Checksum> - sum of 64 <Data> bytes, modulo 0xff |
| * <CMD Checksum> - sum of 77 bytes, from 0xff to <Data Checksum> |
| * |
| * Each write command is split into 5 i2c write transactions of up to 16 bytes. |
| * Each transaction starts with an i2c register offset: (00, 10, 20, 30, 40). |
| */ |
| static int cyapa_gen3_write_fw_block(struct cyapa *cyapa, |
| u16 block, const u8 *data) |
| { |
| int ret; |
| struct gen3_write_block_cmd write_block_cmd; |
| u8 status[BL_STATUS_SIZE]; |
| int tries; |
| u8 bl_status, bl_error; |
| |
| /* Set write command and security key bytes. */ |
| write_block_cmd.checksum_seed = GEN3_BL_CMD_CHECKSUM_SEED; |
| write_block_cmd.cmd_code = GEN3_BL_CMD_WRITE_BLOCK; |
| memcpy(write_block_cmd.key, security_key, sizeof(security_key)); |
| put_unaligned_be16(block, &write_block_cmd.block_num); |
| memcpy(write_block_cmd.block_data, data, CYAPA_FW_BLOCK_SIZE); |
| write_block_cmd.block_checksum = cyapa_gen3_csum( |
| write_block_cmd.block_data, CYAPA_FW_BLOCK_SIZE); |
| write_block_cmd.cmd_checksum = cyapa_gen3_csum((u8 *)&write_block_cmd, |
| sizeof(write_block_cmd) - 1); |
| |
| ret = cyapa_gen3_write_buffer(cyapa, (u8 *)&write_block_cmd, |
| sizeof(write_block_cmd)); |
| if (ret) |
| return ret; |
| |
| /* Wait for write to finish */ |
| tries = 11; /* Programming for one block can take about 100ms. */ |
| do { |
| usleep_range(10000, 20000); |
| |
| /* Check block write command result status. */ |
| ret = cyapa_i2c_reg_read_block(cyapa, BL_HEAD_OFFSET, |
| BL_STATUS_SIZE, status); |
| if (ret != BL_STATUS_SIZE) |
| return (ret < 0) ? ret : -EIO; |
| } while ((status[REG_BL_STATUS] & BL_STATUS_BUSY) && --tries); |
| |
| /* Ignore WATCHDOG bit and reserved bits. */ |
| bl_status = status[REG_BL_STATUS] & ~BL_STATUS_REV_MASK; |
| bl_error = status[REG_BL_ERROR] & ~BL_ERROR_RESERVED; |
| |
| if (bl_status & BL_STATUS_BUSY) |
| ret = -ETIMEDOUT; |
| else if (bl_status != BL_STATUS_RUNNING || |
| bl_error != BL_ERROR_BOOTLOADING) |
| ret = -EIO; |
| else |
| ret = 0; |
| |
| return ret; |
| } |
| |
| static int cyapa_gen3_write_blocks(struct cyapa *cyapa, |
| size_t start_block, size_t block_count, |
| const u8 *image_data) |
| { |
| int error; |
| int i; |
| |
| for (i = 0; i < block_count; i++) { |
| size_t block = start_block + i; |
| size_t addr = i * CYAPA_FW_BLOCK_SIZE; |
| const u8 *data = &image_data[addr]; |
| |
| error = cyapa_gen3_write_fw_block(cyapa, block, data); |
| if (error) |
| return error; |
| } |
| return 0; |
| } |
| |
| static int cyapa_gen3_do_fw_update(struct cyapa *cyapa, |
| const struct firmware *fw) |
| { |
| struct device *dev = &cyapa->client->dev; |
| int error; |
| |
| /* First write data, starting at byte 128 of fw->data */ |
| error = cyapa_gen3_write_blocks(cyapa, |
| CYAPA_FW_DATA_BLOCK_START, CYAPA_FW_DATA_BLOCK_COUNT, |
| &fw->data[CYAPA_FW_HDR_BLOCK_COUNT * CYAPA_FW_BLOCK_SIZE]); |
| if (error) { |
| dev_err(dev, "FW update aborted, write image: %d\n", error); |
| return error; |
| } |
| |
| /* Then write checksum */ |
| error = cyapa_gen3_write_blocks(cyapa, |
| CYAPA_FW_HDR_BLOCK_START, CYAPA_FW_HDR_BLOCK_COUNT, |
| &fw->data[0]); |
| if (error) { |
| dev_err(dev, "FW update aborted, write checksum: %d\n", error); |
| return error; |
| } |
| |
| return 0; |
| } |
| |
| static ssize_t cyapa_gen3_do_calibrate(struct device *dev, |
| struct device_attribute *attr, |
| const char *buf, size_t count) |
| { |
| struct cyapa *cyapa = dev_get_drvdata(dev); |
| unsigned long timeout; |
| int ret; |
| |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); |
| if (ret < 0) { |
| dev_err(dev, "Error reading dev status: %d\n", ret); |
| goto out; |
| } |
| if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) { |
| dev_warn(dev, "Trackpad device is busy, device state: 0x%02x\n", |
| ret); |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, |
| OP_RECALIBRATION_MASK); |
| if (ret < 0) { |
| dev_err(dev, "Failed to send calibrate command: %d\n", |
| ret); |
| goto out; |
| } |
| |
| /* max recalibration timeout 2s. */ |
| timeout = jiffies + 2 * HZ; |
| do { |
| /* |
| * For this recalibration, the max time will not exceed 2s. |
| * The average time is approximately 500 - 700 ms, and we |
| * will check the status every 100 - 200ms. |
| */ |
| msleep(100); |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); |
| if (ret < 0) { |
| dev_err(dev, "Error reading dev status: %d\n", ret); |
| goto out; |
| } |
| if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL) { |
| dev_dbg(dev, "Calibration successful.\n"); |
| goto out; |
| } |
| } while (time_is_after_jiffies(timeout)); |
| |
| dev_err(dev, "Failed to calibrate. Timeout.\n"); |
| ret = -ETIMEDOUT; |
| |
| out: |
| return ret < 0 ? ret : count; |
| } |
| |
| static ssize_t cyapa_gen3_show_baseline(struct device *dev, |
| struct device_attribute *attr, char *buf) |
| { |
| struct cyapa *cyapa = dev_get_drvdata(dev); |
| int max_baseline, min_baseline; |
| int tries; |
| int ret; |
| |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); |
| if (ret < 0) { |
| dev_err(dev, "Error reading dev status. err = %d\n", ret); |
| goto out; |
| } |
| if ((ret & CYAPA_DEV_NORMAL) != CYAPA_DEV_NORMAL) { |
| dev_warn(dev, "Trackpad device is busy. device state = 0x%x\n", |
| ret); |
| ret = -EAGAIN; |
| goto out; |
| } |
| |
| ret = cyapa_write_byte(cyapa, CYAPA_CMD_SOFT_RESET, |
| OP_REPORT_BASELINE_MASK); |
| if (ret < 0) { |
| dev_err(dev, "Failed to send report baseline command. %d\n", |
| ret); |
| goto out; |
| } |
| |
| tries = 3; /* Try for 30 to 60 ms */ |
| do { |
| usleep_range(10000, 20000); |
| |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_DEV_STATUS); |
| if (ret < 0) { |
| dev_err(dev, "Error reading dev status. err = %d\n", |
| ret); |
| goto out; |
| } |
| if ((ret & CYAPA_DEV_NORMAL) == CYAPA_DEV_NORMAL) |
| break; |
| } while (--tries); |
| |
| if (tries == 0) { |
| dev_err(dev, "Device timed out going to Normal state.\n"); |
| ret = -ETIMEDOUT; |
| goto out; |
| } |
| |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_MAX_BASELINE); |
| if (ret < 0) { |
| dev_err(dev, "Failed to read max baseline. err = %d\n", ret); |
| goto out; |
| } |
| max_baseline = ret; |
| |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_MIN_BASELINE); |
| if (ret < 0) { |
| dev_err(dev, "Failed to read min baseline. err = %d\n", ret); |
| goto out; |
| } |
| min_baseline = ret; |
| |
| dev_dbg(dev, "Baseline report successful. Max: %d Min: %d\n", |
| max_baseline, min_baseline); |
| ret = sysfs_emit(buf, "%d %d\n", max_baseline, min_baseline); |
| |
| out: |
| return ret; |
| } |
| |
| /* |
| * cyapa_get_wait_time_for_pwr_cmd |
| * |
| * Compute the amount of time we need to wait after updating the touchpad |
| * power mode. The touchpad needs to consume the incoming power mode set |
| * command at the current clock rate. |
| */ |
| |
| static u16 cyapa_get_wait_time_for_pwr_cmd(u8 pwr_mode) |
| { |
| switch (pwr_mode) { |
| case PWR_MODE_FULL_ACTIVE: return 20; |
| case PWR_MODE_BTN_ONLY: return 20; |
| case PWR_MODE_OFF: return 20; |
| default: return cyapa_pwr_cmd_to_sleep_time(pwr_mode) + 50; |
| } |
| } |
| |
| /* |
| * Set device power mode |
| * |
| * Write to the field to configure power state. Power states include : |
| * Full : Max scans and report rate. |
| * Idle : Report rate set by user specified time. |
| * ButtonOnly : No scans for fingers. When the button is triggered, |
| * a slave interrupt is asserted to notify host to wake up. |
| * Off : Only awake for i2c commands from host. No function for button |
| * or touch sensors. |
| * |
| * The power_mode command should conform to the following : |
| * Full : 0x3f |
| * Idle : Configurable from 20 to 1000ms. See note below for |
| * cyapa_sleep_time_to_pwr_cmd and cyapa_pwr_cmd_to_sleep_time |
| * ButtonOnly : 0x01 |
| * Off : 0x00 |
| * |
| * Device power mode can only be set when device is in operational mode. |
| */ |
| static int cyapa_gen3_set_power_mode(struct cyapa *cyapa, u8 power_mode, |
| u16 always_unused, enum cyapa_pm_stage pm_stage) |
| { |
| struct input_dev *input = cyapa->input; |
| u8 power; |
| int tries; |
| int sleep_time; |
| int interval; |
| int ret; |
| |
| if (cyapa->state != CYAPA_STATE_OP) |
| return 0; |
| |
| tries = SET_POWER_MODE_TRIES; |
| while (tries--) { |
| ret = cyapa_read_byte(cyapa, CYAPA_CMD_POWER_MODE); |
| if (ret >= 0) |
| break; |
| usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY); |
| } |
| if (ret < 0) |
| return ret; |
| |
| /* |
| * Return early if the power mode to set is the same as the current |
| * one. |
| */ |
| if ((ret & PWR_MODE_MASK) == power_mode) |
| return 0; |
| |
| sleep_time = (int)cyapa_get_wait_time_for_pwr_cmd(ret & PWR_MODE_MASK); |
| power = ret; |
| power &= ~PWR_MODE_MASK; |
| power |= power_mode & PWR_MODE_MASK; |
| tries = SET_POWER_MODE_TRIES; |
| while (tries--) { |
| ret = cyapa_write_byte(cyapa, CYAPA_CMD_POWER_MODE, power); |
| if (!ret) |
| break; |
| usleep_range(SET_POWER_MODE_DELAY, 2 * SET_POWER_MODE_DELAY); |
| } |
| |
| /* |
| * Wait for the newly set power command to go in at the previous |
| * clock speed (scanrate) used by the touchpad firmware. Not |
| * doing so before issuing the next command may result in errors |
| * depending on the command's content. |
| */ |
| if (cyapa->operational && |
| input && input_device_enabled(input) && |
| (pm_stage == CYAPA_PM_RUNTIME_SUSPEND || |
| pm_stage == CYAPA_PM_RUNTIME_RESUME)) { |
| /* Try to polling in 120Hz, read may fail, just ignore it. */ |
| interval = 1000 / 120; |
| while (sleep_time > 0) { |
| if (sleep_time > interval) |
| msleep(interval); |
| else |
| msleep(sleep_time); |
| sleep_time -= interval; |
| cyapa_gen3_try_poll_handler(cyapa); |
| } |
| } else { |
| msleep(sleep_time); |
| } |
| |
| return ret; |
| } |
| |
| static int cyapa_gen3_set_proximity(struct cyapa *cyapa, bool enable) |
| { |
| return -EOPNOTSUPP; |
| } |
| |
| static int cyapa_gen3_get_query_data(struct cyapa *cyapa) |
| { |
| u8 query_data[QUERY_DATA_SIZE]; |
| int ret; |
| |
| if (cyapa->state != CYAPA_STATE_OP) |
| return -EBUSY; |
| |
| ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_QUERY, query_data); |
| if (ret != QUERY_DATA_SIZE) |
| return (ret < 0) ? ret : -EIO; |
| |
| memcpy(&cyapa->product_id[0], &query_data[0], 5); |
| cyapa->product_id[5] = '-'; |
| memcpy(&cyapa->product_id[6], &query_data[5], 6); |
| cyapa->product_id[12] = '-'; |
| memcpy(&cyapa->product_id[13], &query_data[11], 2); |
| cyapa->product_id[15] = '\0'; |
| |
| cyapa->fw_maj_ver = query_data[15]; |
| cyapa->fw_min_ver = query_data[16]; |
| |
| cyapa->btn_capability = query_data[19] & CAPABILITY_BTN_MASK; |
| |
| cyapa->gen = query_data[20] & 0x0f; |
| |
| cyapa->max_abs_x = ((query_data[21] & 0xf0) << 4) | query_data[22]; |
| cyapa->max_abs_y = ((query_data[21] & 0x0f) << 8) | query_data[23]; |
| |
| cyapa->physical_size_x = |
| ((query_data[24] & 0xf0) << 4) | query_data[25]; |
| cyapa->physical_size_y = |
| ((query_data[24] & 0x0f) << 8) | query_data[26]; |
| |
| cyapa->max_z = 255; |
| |
| return 0; |
| } |
| |
| static int cyapa_gen3_bl_query_data(struct cyapa *cyapa) |
| { |
| u8 bl_data[CYAPA_CMD_LEN]; |
| int ret; |
| |
| ret = cyapa_i2c_reg_read_block(cyapa, 0, CYAPA_CMD_LEN, bl_data); |
| if (ret != CYAPA_CMD_LEN) |
| return (ret < 0) ? ret : -EIO; |
| |
| /* |
| * This value will be updated again when entered application mode. |
| * If TP failed to enter application mode, this fw version values |
| * can be used as a reference. |
| * This firmware version valid when fw image checksum is valid. |
| */ |
| if (bl_data[REG_BL_STATUS] == |
| (BL_STATUS_RUNNING | BL_STATUS_CSUM_VALID)) { |
| cyapa->fw_maj_ver = bl_data[GEN3_BL_IDLE_FW_MAJ_VER_OFFSET]; |
| cyapa->fw_min_ver = bl_data[GEN3_BL_IDLE_FW_MIN_VER_OFFSET]; |
| } |
| |
| return 0; |
| } |
| |
| /* |
| * Check if device is operational. |
| * |
| * An operational device is responding, has exited bootloader, and has |
| * firmware supported by this driver. |
| * |
| * Returns: |
| * -EBUSY no device or in bootloader |
| * -EIO failure while reading from device |
| * -EAGAIN device is still in bootloader |
| * if ->state = CYAPA_STATE_BL_IDLE, device has invalid firmware |
| * -EINVAL device is in operational mode, but not supported by this driver |
| * 0 device is supported |
| */ |
| static int cyapa_gen3_do_operational_check(struct cyapa *cyapa) |
| { |
| struct device *dev = &cyapa->client->dev; |
| int error; |
| |
| switch (cyapa->state) { |
| case CYAPA_STATE_BL_ACTIVE: |
| error = cyapa_gen3_bl_deactivate(cyapa); |
| if (error) { |
| dev_err(dev, "failed to bl_deactivate: %d\n", error); |
| return error; |
| } |
| |
| fallthrough; |
| case CYAPA_STATE_BL_IDLE: |
| /* Try to get firmware version in bootloader mode. */ |
| cyapa_gen3_bl_query_data(cyapa); |
| |
| error = cyapa_gen3_bl_exit(cyapa); |
| if (error) { |
| dev_err(dev, "failed to bl_exit: %d\n", error); |
| return error; |
| } |
| |
| fallthrough; |
| case CYAPA_STATE_OP: |
| /* |
| * Reading query data before going back to the full mode |
| * may cause problems, so we set the power mode first here. |
| */ |
| error = cyapa_gen3_set_power_mode(cyapa, |
| PWR_MODE_FULL_ACTIVE, 0, CYAPA_PM_ACTIVE); |
| if (error) |
| dev_err(dev, "%s: set full power mode failed: %d\n", |
| __func__, error); |
| error = cyapa_gen3_get_query_data(cyapa); |
| if (error < 0) |
| return error; |
| |
| /* Only support firmware protocol gen3 */ |
| if (cyapa->gen != CYAPA_GEN3) { |
| dev_err(dev, "unsupported protocol version (%d)", |
| cyapa->gen); |
| return -EINVAL; |
| } |
| |
| /* Only support product ID starting with CYTRA */ |
| if (memcmp(cyapa->product_id, product_id, |
| strlen(product_id)) != 0) { |
| dev_err(dev, "unsupported product ID (%s)\n", |
| cyapa->product_id); |
| return -EINVAL; |
| } |
| |
| return 0; |
| |
| default: |
| return -EIO; |
| } |
| return 0; |
| } |
| |
| /* |
| * Return false, do not continue process |
| * Return true, continue process. |
| */ |
| static bool cyapa_gen3_irq_cmd_handler(struct cyapa *cyapa) |
| { |
| /* Not gen3 irq command response, skip for continue. */ |
| if (cyapa->gen != CYAPA_GEN3) |
| return true; |
| |
| if (cyapa->operational) |
| return true; |
| |
| /* |
| * Driver in detecting or other interface function processing, |
| * so, stop cyapa_gen3_irq_handler to continue process to |
| * avoid unwanted to error detecting and processing. |
| * |
| * And also, avoid the periodically asserted interrupts to be processed |
| * as touch inputs when gen3 failed to launch into application mode, |
| * which will cause gen3 stays in bootloader mode. |
| */ |
| return false; |
| } |
| |
| static int cyapa_gen3_event_process(struct cyapa *cyapa, |
| struct cyapa_reg_data *data) |
| { |
| struct input_dev *input = cyapa->input; |
| int num_fingers; |
| int i; |
| |
| num_fingers = (data->finger_btn >> 4) & 0x0f; |
| for (i = 0; i < num_fingers; i++) { |
| const struct cyapa_touch *touch = &data->touches[i]; |
| /* Note: touch->id range is 1 to 15; slots are 0 to 14. */ |
| int slot = touch->id - 1; |
| |
| input_mt_slot(input, slot); |
| input_mt_report_slot_state(input, MT_TOOL_FINGER, true); |
| input_report_abs(input, ABS_MT_POSITION_X, |
| ((touch->xy_hi & 0xf0) << 4) | touch->x_lo); |
| input_report_abs(input, ABS_MT_POSITION_Y, |
| ((touch->xy_hi & 0x0f) << 8) | touch->y_lo); |
| input_report_abs(input, ABS_MT_PRESSURE, touch->pressure); |
| } |
| |
| input_mt_sync_frame(input); |
| |
| if (cyapa->btn_capability & CAPABILITY_LEFT_BTN_MASK) |
| input_report_key(input, BTN_LEFT, |
| !!(data->finger_btn & OP_DATA_LEFT_BTN)); |
| if (cyapa->btn_capability & CAPABILITY_MIDDLE_BTN_MASK) |
| input_report_key(input, BTN_MIDDLE, |
| !!(data->finger_btn & OP_DATA_MIDDLE_BTN)); |
| if (cyapa->btn_capability & CAPABILITY_RIGHT_BTN_MASK) |
| input_report_key(input, BTN_RIGHT, |
| !!(data->finger_btn & OP_DATA_RIGHT_BTN)); |
| input_sync(input); |
| |
| return 0; |
| } |
| |
| static int cyapa_gen3_irq_handler(struct cyapa *cyapa) |
| { |
| struct device *dev = &cyapa->client->dev; |
| struct cyapa_reg_data data; |
| int ret; |
| |
| ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data); |
| if (ret != sizeof(data)) { |
| dev_err(dev, "failed to read report data, (%d)\n", ret); |
| return -EINVAL; |
| } |
| |
| if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC || |
| (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL || |
| (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) { |
| dev_err(dev, "invalid device state bytes: %02x %02x\n", |
| data.device_status, data.finger_btn); |
| return -EINVAL; |
| } |
| |
| return cyapa_gen3_event_process(cyapa, &data); |
| } |
| |
| /* |
| * This function will be called in the cyapa_gen3_set_power_mode function, |
| * and it's known that it may failed in some situation after the set power |
| * mode command was sent. So this function is aimed to avoid the knwon |
| * and unwanted output I2C and data parse error messages. |
| */ |
| static int cyapa_gen3_try_poll_handler(struct cyapa *cyapa) |
| { |
| struct cyapa_reg_data data; |
| int ret; |
| |
| ret = cyapa_read_block(cyapa, CYAPA_CMD_GROUP_DATA, (u8 *)&data); |
| if (ret != sizeof(data)) |
| return -EINVAL; |
| |
| if ((data.device_status & OP_STATUS_SRC) != OP_STATUS_SRC || |
| (data.device_status & OP_STATUS_DEV) != CYAPA_DEV_NORMAL || |
| (data.finger_btn & OP_DATA_VALID) != OP_DATA_VALID) |
| return -EINVAL; |
| |
| return cyapa_gen3_event_process(cyapa, &data); |
| |
| } |
| |
| static int cyapa_gen3_initialize(struct cyapa *cyapa) { return 0; } |
| static int cyapa_gen3_bl_initiate(struct cyapa *cyapa, |
| const struct firmware *fw) { return 0; } |
| static int cyapa_gen3_empty_output_data(struct cyapa *cyapa, |
| u8 *buf, int *len, cb_sort func) { return 0; } |
| |
| const struct cyapa_dev_ops cyapa_gen3_ops = { |
| .check_fw = cyapa_gen3_check_fw, |
| .bl_enter = cyapa_gen3_bl_enter, |
| .bl_activate = cyapa_gen3_bl_activate, |
| .update_fw = cyapa_gen3_do_fw_update, |
| .bl_deactivate = cyapa_gen3_bl_deactivate, |
| .bl_initiate = cyapa_gen3_bl_initiate, |
| |
| .show_baseline = cyapa_gen3_show_baseline, |
| .calibrate_store = cyapa_gen3_do_calibrate, |
| |
| .initialize = cyapa_gen3_initialize, |
| |
| .state_parse = cyapa_gen3_state_parse, |
| .operational_check = cyapa_gen3_do_operational_check, |
| |
| .irq_handler = cyapa_gen3_irq_handler, |
| .irq_cmd_handler = cyapa_gen3_irq_cmd_handler, |
| .sort_empty_output_data = cyapa_gen3_empty_output_data, |
| .set_power_mode = cyapa_gen3_set_power_mode, |
| |
| .set_proximity = cyapa_gen3_set_proximity, |
| }; |