blob: 5e1277fea7250b4132039efb18f1cfaafdc5257e [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
/*
* IPQ6018 SoC device tree source
*
* Copyright (c) 2019, The Linux Foundation. All rights reserved.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-ipq6018.h>
#include <dt-bindings/reset/qcom,gcc-ipq6018.h>
#include <dt-bindings/clock/qcom,apss-ipq.h>
/ {
#address-cells = <2>;
#size-cells = <2>;
interrupt-parent = <&intc>;
clocks {
sleep_clk: sleep-clk {
compatible = "fixed-clock";
clock-frequency = <32000>;
#clock-cells = <0>;
};
xo: xo {
compatible = "fixed-clock";
clock-frequency = <24000000>;
#clock-cells = <0>;
};
};
cpus: cpus {
#address-cells = <1>;
#size-cells = <0>;
CPU0: cpu@0 {
device_type = "cpu";
compatible = "arm,cortex-a53";
reg = <0x0>;
enable-method = "psci";
next-level-cache = <&L2_0>;
clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
clock-names = "cpu";
operating-points-v2 = <&cpu_opp_table>;
cpu-supply = <&ipq6018_s2>;
};
CPU1: cpu@1 {
device_type = "cpu";
compatible = "arm,cortex-a53";
enable-method = "psci";
reg = <0x1>;
next-level-cache = <&L2_0>;
clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
clock-names = "cpu";
operating-points-v2 = <&cpu_opp_table>;
cpu-supply = <&ipq6018_s2>;
};
CPU2: cpu@2 {
device_type = "cpu";
compatible = "arm,cortex-a53";
enable-method = "psci";
reg = <0x2>;
next-level-cache = <&L2_0>;
clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
clock-names = "cpu";
operating-points-v2 = <&cpu_opp_table>;
cpu-supply = <&ipq6018_s2>;
};
CPU3: cpu@3 {
device_type = "cpu";
compatible = "arm,cortex-a53";
enable-method = "psci";
reg = <0x3>;
next-level-cache = <&L2_0>;
clocks = <&apcs_glb APCS_ALIAS0_CORE_CLK>;
clock-names = "cpu";
operating-points-v2 = <&cpu_opp_table>;
cpu-supply = <&ipq6018_s2>;
};
L2_0: l2-cache {
compatible = "cache";
cache-level = <2>;
cache-unified;
};
};
firmware {
scm {
compatible = "qcom,scm-ipq6018", "qcom,scm";
qcom,dload-mode = <&tcsr 0x6100>;
};
};
cpu_opp_table: opp-table-cpu {
compatible = "operating-points-v2-kryo-cpu";
nvmem-cells = <&cpu_speed_bin>;
opp-shared;
opp-864000000 {
opp-hz = /bits/ 64 <864000000>;
opp-microvolt = <725000>;
opp-supported-hw = <0xf>;
clock-latency-ns = <200000>;
};
opp-1056000000 {
opp-hz = /bits/ 64 <1056000000>;
opp-microvolt = <787500>;
opp-supported-hw = <0xf>;
clock-latency-ns = <200000>;
};
opp-1320000000 {
opp-hz = /bits/ 64 <1320000000>;
opp-microvolt = <862500>;
opp-supported-hw = <0x3>;
clock-latency-ns = <200000>;
};
opp-1440000000 {
opp-hz = /bits/ 64 <1440000000>;
opp-microvolt = <925000>;
opp-supported-hw = <0x3>;
clock-latency-ns = <200000>;
};
opp-1608000000 {
opp-hz = /bits/ 64 <1608000000>;
opp-microvolt = <987500>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-1800000000 {
opp-hz = /bits/ 64 <1800000000>;
opp-microvolt = <1062500>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
};
pmuv8: pmu {
compatible = "arm,cortex-a53-pmu";
interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
psci: psci {
compatible = "arm,psci-1.0";
method = "smc";
};
rpm: remoteproc {
compatible = "qcom,ipq6018-rpm-proc", "qcom,rpm-proc";
glink-edge {
compatible = "qcom,glink-rpm";
interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>;
qcom,rpm-msg-ram = <&rpm_msg_ram>;
mboxes = <&apcs_glb 0>;
rpm_requests: rpm-requests {
compatible = "qcom,rpm-ipq6018";
qcom,glink-channels = "rpm_requests";
regulators {
compatible = "qcom,rpm-mp5496-regulators";
ipq6018_s2: s2 {
regulator-min-microvolt = <725000>;
regulator-max-microvolt = <1062500>;
regulator-always-on;
};
};
};
};
};
reserved-memory {
#address-cells = <2>;
#size-cells = <2>;
ranges;
rpm_msg_ram: memory@60000 {
reg = <0x0 0x00060000 0x0 0x6000>;
no-map;
};
bootloader@4a100000 {
reg = <0x0 0x4a100000 0x0 0x400000>;
no-map;
};
sbl@4a500000 {
reg = <0x0 0x4a500000 0x0 0x100000>;
no-map;
};
tz: memory@4a600000 {
reg = <0x0 0x4a600000 0x0 0x400000>;
no-map;
};
smem_region: memory@4aa00000 {
reg = <0x0 0x4aa00000 0x0 0x100000>;
no-map;
};
q6_region: memory@4ab00000 {
reg = <0x0 0x4ab00000 0x0 0x5500000>;
no-map;
};
};
smem {
compatible = "qcom,smem";
memory-region = <&smem_region>;
hwlocks = <&tcsr_mutex 3>;
};
soc: soc@0 {
#address-cells = <2>;
#size-cells = <2>;
ranges = <0 0 0 0 0x0 0xffffffff>;
dma-ranges;
compatible = "simple-bus";
qusb_phy_1: qusb@59000 {
compatible = "qcom,ipq6018-qusb2-phy";
reg = <0x0 0x00059000 0x0 0x180>;
#phy-cells = <0>;
clocks = <&gcc GCC_USB1_PHY_CFG_AHB_CLK>,
<&xo>;
clock-names = "cfg_ahb", "ref";
resets = <&gcc GCC_QUSB2_1_PHY_BCR>;
status = "disabled";
};
ssphy_0: ssphy@78000 {
compatible = "qcom,ipq6018-qmp-usb3-phy";
reg = <0x0 0x00078000 0x0 0x1000>;
clocks = <&gcc GCC_USB0_AUX_CLK>,
<&xo>,
<&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
<&gcc GCC_USB0_PIPE_CLK>;
clock-names = "aux",
"ref",
"cfg_ahb",
"pipe";
clock-output-names = "gcc_usb0_pipe_clk_src";
#clock-cells = <0>;
#phy-cells = <0>;
resets = <&gcc GCC_USB0_PHY_BCR>,
<&gcc GCC_USB3PHY_0_PHY_BCR>;
reset-names = "phy",
"phy_phy";
status = "disabled";
};
qusb_phy_0: qusb@79000 {
compatible = "qcom,ipq6018-qusb2-phy";
reg = <0x0 0x00079000 0x0 0x180>;
#phy-cells = <0>;
clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>,
<&xo>;
clock-names = "cfg_ahb", "ref";
resets = <&gcc GCC_QUSB2_0_PHY_BCR>;
status = "disabled";
};
pcie_phy: phy@84000 {
compatible = "qcom,ipq6018-qmp-pcie-phy";
reg = <0x0 0x00084000 0x0 0x1000>;
status = "disabled";
clocks = <&gcc GCC_PCIE0_AUX_CLK>,
<&gcc GCC_PCIE0_AHB_CLK>,
<&gcc GCC_PCIE0_PIPE_CLK>;
clock-names = "aux",
"cfg_ahb",
"pipe";
clock-output-names = "gcc_pcie0_pipe_clk_src";
#clock-cells = <0>;
#phy-cells = <0>;
resets = <&gcc GCC_PCIE0_PHY_BCR>,
<&gcc GCC_PCIE0PHY_PHY_BCR>;
reset-names = "phy",
"common";
};
mdio: mdio@90000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "qcom,ipq6018-mdio", "qcom,ipq4019-mdio";
reg = <0x0 0x00090000 0x0 0x64>;
clocks = <&gcc GCC_MDIO_AHB_CLK>;
clock-names = "gcc_mdio_ahb_clk";
status = "disabled";
};
qfprom: efuse@a4000 {
compatible = "qcom,ipq6018-qfprom", "qcom,qfprom";
reg = <0x0 0x000a4000 0x0 0x2000>;
#address-cells = <1>;
#size-cells = <1>;
cpu_speed_bin: cpu-speed-bin@135 {
reg = <0x135 0x1>;
bits = <7 1>;
};
};
prng: qrng@e3000 {
compatible = "qcom,prng-ee";
reg = <0x0 0x000e3000 0x0 0x1000>;
clocks = <&gcc GCC_PRNG_AHB_CLK>;
clock-names = "core";
};
cryptobam: dma-controller@704000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x00704000 0x0 0x20000>;
interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_CRYPTO_AHB_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <1>;
qcom,controlled-remotely;
};
crypto: crypto@73a000 {
compatible = "qcom,crypto-v5.1";
reg = <0x0 0x0073a000 0x0 0x6000>;
clocks = <&gcc GCC_CRYPTO_AHB_CLK>,
<&gcc GCC_CRYPTO_AXI_CLK>,
<&gcc GCC_CRYPTO_CLK>;
clock-names = "iface", "bus", "core";
dmas = <&cryptobam 2>, <&cryptobam 3>;
dma-names = "rx", "tx";
};
tlmm: pinctrl@1000000 {
compatible = "qcom,ipq6018-pinctrl";
reg = <0x0 0x01000000 0x0 0x300000>;
interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
gpio-controller;
#gpio-cells = <2>;
gpio-ranges = <&tlmm 0 0 80>;
interrupt-controller;
#interrupt-cells = <2>;
serial_3_pins: serial3-state {
pins = "gpio44", "gpio45";
function = "blsp2_uart";
drive-strength = <8>;
bias-pull-down;
};
qpic_pins: qpic-state {
pins = "gpio1", "gpio3", "gpio4",
"gpio5", "gpio6", "gpio7",
"gpio8", "gpio10", "gpio11",
"gpio12", "gpio13", "gpio14",
"gpio15", "gpio17";
function = "qpic_pad";
drive-strength = <8>;
bias-disable;
};
};
gcc: gcc@1800000 {
compatible = "qcom,gcc-ipq6018";
reg = <0x0 0x01800000 0x0 0x80000>;
clocks = <&xo>, <&sleep_clk>;
clock-names = "xo", "sleep_clk";
#clock-cells = <1>;
#reset-cells = <1>;
};
tcsr_mutex: hwlock@1905000 {
compatible = "qcom,ipq6018-tcsr-mutex", "qcom,tcsr-mutex";
reg = <0x0 0x01905000 0x0 0x20000>;
#hwlock-cells = <1>;
};
tcsr: syscon@1937000 {
compatible = "qcom,tcsr-ipq6018", "syscon";
reg = <0x0 0x01937000 0x0 0x21000>;
};
usb2: usb@70f8800 {
compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
reg = <0x0 0x070f8800 0x0 0x400>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_USB1_MASTER_CLK>,
<&gcc GCC_USB1_SLEEP_CLK>,
<&gcc GCC_USB1_MOCK_UTMI_CLK>;
clock-names = "core",
"sleep",
"mock_utmi";
assigned-clocks = <&gcc GCC_USB1_MASTER_CLK>,
<&gcc GCC_USB1_MOCK_UTMI_CLK>;
assigned-clock-rates = <133330000>,
<24000000>;
resets = <&gcc GCC_USB1_BCR>;
status = "disabled";
dwc_1: usb@7000000 {
compatible = "snps,dwc3";
reg = <0x0 0x07000000 0x0 0xcd00>;
interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>;
phys = <&qusb_phy_1>;
phy-names = "usb2-phy";
tx-fifo-resize;
snps,is-utmi-l1-suspend;
snps,hird-threshold = /bits/ 8 <0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_u3_susphy_quirk;
dr_mode = "host";
};
};
blsp_dma: dma-controller@7884000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x07884000 0x0 0x2b000>;
interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
};
blsp1_uart1: serial@78af000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x78af000 0x0 0x200>;
interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_uart2: serial@78b0000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x78b0000 0x0 0x200>;
interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_uart3: serial@78b1000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x078b1000 0x0 0x200>;
interrupts = <GIC_SPI 306 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART3_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_uart4: serial@78b2000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x078b2000 0x0 0x200>;
interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_uart5: serial@78b3000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x78b3000 0x0 0x200>;
interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_uart6: serial@78b4000 {
compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
reg = <0x0 0x078b4000 0x0 0x200>;
interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_UART6_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
status = "disabled";
};
blsp1_spi1: spi@78b5000 {
compatible = "qcom,spi-qup-v2.2.1";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x078b5000 0x0 0x600>;
interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
dmas = <&blsp_dma 12>, <&blsp_dma 13>;
dma-names = "tx", "rx";
status = "disabled";
};
blsp1_spi2: spi@78b6000 {
compatible = "qcom,spi-qup-v2.2.1";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x078b6000 0x0 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
dmas = <&blsp_dma 14>, <&blsp_dma 15>;
dma-names = "tx", "rx";
status = "disabled";
};
blsp1_spi5: spi@78b9000 {
compatible = "qcom,spi-qup-v2.2.1";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x078b9000 0x0 0x600>;
interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
dmas = <&blsp_dma 20>, <&blsp_dma 21>;
dma-names = "tx", "rx";
status = "disabled";
};
blsp1_i2c2: i2c@78b6000 {
compatible = "qcom,i2c-qup-v2.2.1";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x078b6000 0x0 0x600>;
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 14>, <&blsp_dma 15>;
dma-names = "tx", "rx";
status = "disabled";
};
blsp1_i2c3: i2c@78b7000 {
compatible = "qcom,i2c-qup-v2.2.1";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x0 0x078b7000 0x0 0x600>;
interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
<&gcc GCC_BLSP1_AHB_CLK>;
clock-names = "core", "iface";
clock-frequency = <400000>;
dmas = <&blsp_dma 16>, <&blsp_dma 17>;
dma-names = "tx", "rx";
status = "disabled";
};
qpic_bam: dma-controller@7984000 {
compatible = "qcom,bam-v1.7.0";
reg = <0x0 0x07984000 0x0 0x1a000>;
interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&gcc GCC_QPIC_AHB_CLK>;
clock-names = "bam_clk";
#dma-cells = <1>;
qcom,ee = <0>;
status = "disabled";
};
qpic_nand: nand-controller@79b0000 {
compatible = "qcom,ipq6018-nand";
reg = <0x0 0x079b0000 0x0 0x10000>;
#address-cells = <1>;
#size-cells = <0>;
clocks = <&gcc GCC_QPIC_CLK>,
<&gcc GCC_QPIC_AHB_CLK>;
clock-names = "core", "aon";
dmas = <&qpic_bam 0>,
<&qpic_bam 1>,
<&qpic_bam 2>;
dma-names = "tx", "rx", "cmd";
pinctrl-0 = <&qpic_pins>;
pinctrl-names = "default";
status = "disabled";
};
usb3: usb@8af8800 {
compatible = "qcom,ipq6018-dwc3", "qcom,dwc3";
reg = <0x0 0x08af8800 0x0 0x400>;
#address-cells = <2>;
#size-cells = <2>;
ranges;
clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
<&gcc GCC_USB0_MASTER_CLK>,
<&gcc GCC_USB0_SLEEP_CLK>,
<&gcc GCC_USB0_MOCK_UTMI_CLK>;
clock-names = "cfg_noc",
"core",
"sleep",
"mock_utmi";
assigned-clocks = <&gcc GCC_SYS_NOC_USB0_AXI_CLK>,
<&gcc GCC_USB0_MASTER_CLK>,
<&gcc GCC_USB0_MOCK_UTMI_CLK>;
assigned-clock-rates = <133330000>,
<133330000>,
<24000000>;
resets = <&gcc GCC_USB0_BCR>;
status = "disabled";
dwc_0: usb@8a00000 {
compatible = "snps,dwc3";
reg = <0x0 0x08a00000 0x0 0xcd00>;
interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
phys = <&qusb_phy_0>, <&ssphy_0>;
phy-names = "usb2-phy", "usb3-phy";
clocks = <&xo>;
clock-names = "ref";
tx-fifo-resize;
snps,is-utmi-l1-suspend;
snps,hird-threshold = /bits/ 8 <0x0>;
snps,dis_u2_susphy_quirk;
snps,dis_u3_susphy_quirk;
dr_mode = "host";
};
};
intc: interrupt-controller@b000000 {
compatible = "qcom,msm-qgic2";
#address-cells = <2>;
#size-cells = <2>;
interrupt-controller;
#interrupt-cells = <3>;
reg = <0x0 0x0b000000 0x0 0x1000>, /*GICD*/
<0x0 0x0b002000 0x0 0x1000>, /*GICC*/
<0x0 0x0b001000 0x0 0x1000>, /*GICH*/
<0x0 0x0b004000 0x0 0x1000>; /*GICV*/
interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
ranges = <0 0 0 0xb00a000 0 0xffd>;
v2m@0 {
compatible = "arm,gic-v2m-frame";
msi-controller;
reg = <0x0 0x0 0x0 0xffd>;
};
};
watchdog@b017000 {
compatible = "qcom,kpss-wdt";
interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
reg = <0x0 0x0b017000 0x0 0x40>;
clocks = <&sleep_clk>;
timeout-sec = <10>;
};
apcs_glb: mailbox@b111000 {
compatible = "qcom,ipq6018-apcs-apps-global";
reg = <0x0 0x0b111000 0x0 0x1000>;
#clock-cells = <1>;
clocks = <&a53pll>, <&xo>, <&gcc GPLL0>;
clock-names = "pll", "xo", "gpll0";
#mbox-cells = <1>;
};
a53pll: clock@b116000 {
compatible = "qcom,ipq6018-a53pll";
reg = <0x0 0x0b116000 0x0 0x40>;
#clock-cells = <0>;
clocks = <&xo>;
clock-names = "xo";
};
timer@b120000 {
#address-cells = <1>;
#size-cells = <1>;
ranges = <0 0 0 0x10000000>;
compatible = "arm,armv7-timer-mem";
reg = <0x0 0x0b120000 0x0 0x1000>;
frame@b120000 {
frame-number = <0>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b121000 0x1000>,
<0x0b122000 0x1000>;
};
frame@b123000 {
frame-number = <1>;
interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b123000 0x1000>;
status = "disabled";
};
frame@b124000 {
frame-number = <2>;
interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b124000 0x1000>;
status = "disabled";
};
frame@b125000 {
frame-number = <3>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b125000 0x1000>;
status = "disabled";
};
frame@b126000 {
frame-number = <4>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b126000 0x1000>;
status = "disabled";
};
frame@b127000 {
frame-number = <5>;
interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b127000 0x1000>;
status = "disabled";
};
frame@b128000 {
frame-number = <6>;
interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x0b128000 0x1000>;
status = "disabled";
};
};
q6v5_wcss: remoteproc@cd00000 {
compatible = "qcom,ipq6018-wcss-pil";
reg = <0x0 0x0cd00000 0x0 0x4040>,
<0x0 0x004ab000 0x0 0x20>;
reg-names = "qdsp6",
"rmb";
interrupts-extended = <&intc GIC_SPI 325 IRQ_TYPE_EDGE_RISING>,
<&wcss_smp2p_in 0 0>,
<&wcss_smp2p_in 1 0>,
<&wcss_smp2p_in 2 0>,
<&wcss_smp2p_in 3 0>;
interrupt-names = "wdog",
"fatal",
"ready",
"handover",
"stop-ack";
resets = <&gcc GCC_WCSSAON_RESET>,
<&gcc GCC_WCSS_BCR>,
<&gcc GCC_WCSS_Q6_BCR>;
reset-names = "wcss_aon_reset",
"wcss_reset",
"wcss_q6_reset";
clocks = <&gcc GCC_PRNG_AHB_CLK>;
clock-names = "prng";
qcom,halt-regs = <&tcsr 0x18000 0x1b000 0xe000>;
qcom,smem-states = <&wcss_smp2p_out 0>,
<&wcss_smp2p_out 1>;
qcom,smem-state-names = "shutdown",
"stop";
memory-region = <&q6_region>;
glink-edge {
interrupts = <GIC_SPI 321 IRQ_TYPE_EDGE_RISING>;
label = "rtr";
qcom,remote-pid = <1>;
mboxes = <&apcs_glb 8>;
qrtr_requests {
qcom,glink-channels = "IPCRTR";
};
};
};
pcie0: pcie@20000000 {
compatible = "qcom,pcie-ipq6018";
reg = <0x0 0x20000000 0x0 0xf1d>,
<0x0 0x20000f20 0x0 0xa8>,
<0x0 0x20001000 0x0 0x1000>,
<0x0 0x80000 0x0 0x4000>,
<0x0 0x20100000 0x0 0x1000>;
reg-names = "dbi", "elbi", "atu", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
max-link-speed = <3>;
#address-cells = <3>;
#size-cells = <2>;
phys = <&pcie_phy>;
phy-names = "pciephy";
ranges = <0x81000000 0x0 0x00000000 0x0 0x20200000 0x0 0x10000>,
<0x82000000 0x0 0x20220000 0x0 0x20220000 0x0 0xfde0000>;
interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 75 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 78 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 79 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 83 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_SYS_NOC_PCIE0_AXI_CLK>,
<&gcc GCC_PCIE0_AXI_M_CLK>,
<&gcc GCC_PCIE0_AXI_S_CLK>,
<&gcc GCC_PCIE0_AXI_S_BRIDGE_CLK>,
<&gcc PCIE0_RCHNG_CLK>;
clock-names = "iface",
"axi_m",
"axi_s",
"axi_bridge",
"rchng";
resets = <&gcc GCC_PCIE0_PIPE_ARES>,
<&gcc GCC_PCIE0_SLEEP_ARES>,
<&gcc GCC_PCIE0_CORE_STICKY_ARES>,
<&gcc GCC_PCIE0_AXI_MASTER_ARES>,
<&gcc GCC_PCIE0_AXI_SLAVE_ARES>,
<&gcc GCC_PCIE0_AHB_ARES>,
<&gcc GCC_PCIE0_AXI_MASTER_STICKY_ARES>,
<&gcc GCC_PCIE0_AXI_SLAVE_STICKY_ARES>;
reset-names = "pipe",
"sleep",
"sticky",
"axi_m",
"axi_s",
"ahb",
"axi_m_sticky",
"axi_s_sticky";
status = "disabled";
};
};
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
wcss: wcss-smp2p {
compatible = "qcom,smp2p";
qcom,smem = <435>, <428>;
interrupt-parent = <&intc>;
interrupts = <GIC_SPI 322 IRQ_TYPE_EDGE_RISING>;
mboxes = <&apcs_glb 9>;
qcom,local-pid = <0>;
qcom,remote-pid = <1>;
wcss_smp2p_out: master-kernel {
qcom,entry-name = "master-kernel";
#qcom,smem-state-cells = <1>;
};
wcss_smp2p_in: slave-kernel {
qcom,entry-name = "slave-kernel";
interrupt-controller;
#interrupt-cells = <2>;
};
};
};