| // SPDX-License-Identifier: ISC |
| /* |
| * Copyright (c) 2005-2011 Atheros Communications Inc. |
| * Copyright (c) 2011-2017 Qualcomm Atheros, Inc. |
| * Copyright (c) 2018-2019, The Linux Foundation. All rights reserved. |
| * Copyright (c) 2021-2024 Qualcomm Innovation Center, Inc. All rights reserved. |
| */ |
| |
| #include "mac.h" |
| |
| #include <net/cfg80211.h> |
| #include <net/mac80211.h> |
| #include <linux/etherdevice.h> |
| #include <linux/acpi.h> |
| #include <linux/of.h> |
| #include <linux/bitfield.h> |
| |
| #include "hif.h" |
| #include "core.h" |
| #include "debug.h" |
| #include "wmi.h" |
| #include "htt.h" |
| #include "txrx.h" |
| #include "testmode.h" |
| #include "wmi-tlv.h" |
| #include "wmi-ops.h" |
| #include "wow.h" |
| #include "leds.h" |
| |
| /*********/ |
| /* Rates */ |
| /*********/ |
| |
| static struct ieee80211_rate ath10k_rates[] = { |
| { .bitrate = 10, |
| .hw_value = ATH10K_HW_RATE_CCK_LP_1M }, |
| { .bitrate = 20, |
| .hw_value = ATH10K_HW_RATE_CCK_LP_2M, |
| .hw_value_short = ATH10K_HW_RATE_CCK_SP_2M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 55, |
| .hw_value = ATH10K_HW_RATE_CCK_LP_5_5M, |
| .hw_value_short = ATH10K_HW_RATE_CCK_SP_5_5M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 110, |
| .hw_value = ATH10K_HW_RATE_CCK_LP_11M, |
| .hw_value_short = ATH10K_HW_RATE_CCK_SP_11M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| |
| { .bitrate = 60, .hw_value = ATH10K_HW_RATE_OFDM_6M }, |
| { .bitrate = 90, .hw_value = ATH10K_HW_RATE_OFDM_9M }, |
| { .bitrate = 120, .hw_value = ATH10K_HW_RATE_OFDM_12M }, |
| { .bitrate = 180, .hw_value = ATH10K_HW_RATE_OFDM_18M }, |
| { .bitrate = 240, .hw_value = ATH10K_HW_RATE_OFDM_24M }, |
| { .bitrate = 360, .hw_value = ATH10K_HW_RATE_OFDM_36M }, |
| { .bitrate = 480, .hw_value = ATH10K_HW_RATE_OFDM_48M }, |
| { .bitrate = 540, .hw_value = ATH10K_HW_RATE_OFDM_54M }, |
| }; |
| |
| static struct ieee80211_rate ath10k_rates_rev2[] = { |
| { .bitrate = 10, |
| .hw_value = ATH10K_HW_RATE_REV2_CCK_LP_1M }, |
| { .bitrate = 20, |
| .hw_value = ATH10K_HW_RATE_REV2_CCK_LP_2M, |
| .hw_value_short = ATH10K_HW_RATE_REV2_CCK_SP_2M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 55, |
| .hw_value = ATH10K_HW_RATE_REV2_CCK_LP_5_5M, |
| .hw_value_short = ATH10K_HW_RATE_REV2_CCK_SP_5_5M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| { .bitrate = 110, |
| .hw_value = ATH10K_HW_RATE_REV2_CCK_LP_11M, |
| .hw_value_short = ATH10K_HW_RATE_REV2_CCK_SP_11M, |
| .flags = IEEE80211_RATE_SHORT_PREAMBLE }, |
| |
| { .bitrate = 60, .hw_value = ATH10K_HW_RATE_OFDM_6M }, |
| { .bitrate = 90, .hw_value = ATH10K_HW_RATE_OFDM_9M }, |
| { .bitrate = 120, .hw_value = ATH10K_HW_RATE_OFDM_12M }, |
| { .bitrate = 180, .hw_value = ATH10K_HW_RATE_OFDM_18M }, |
| { .bitrate = 240, .hw_value = ATH10K_HW_RATE_OFDM_24M }, |
| { .bitrate = 360, .hw_value = ATH10K_HW_RATE_OFDM_36M }, |
| { .bitrate = 480, .hw_value = ATH10K_HW_RATE_OFDM_48M }, |
| { .bitrate = 540, .hw_value = ATH10K_HW_RATE_OFDM_54M }, |
| }; |
| |
| static const struct cfg80211_sar_freq_ranges ath10k_sar_freq_ranges[] = { |
| {.start_freq = 2402, .end_freq = 2494 }, |
| {.start_freq = 5170, .end_freq = 5875 }, |
| }; |
| |
| static const struct cfg80211_sar_capa ath10k_sar_capa = { |
| .type = NL80211_SAR_TYPE_POWER, |
| .num_freq_ranges = (ARRAY_SIZE(ath10k_sar_freq_ranges)), |
| .freq_ranges = &ath10k_sar_freq_ranges[0], |
| }; |
| |
| #define ATH10K_MAC_FIRST_OFDM_RATE_IDX 4 |
| |
| #define ath10k_a_rates (ath10k_rates + ATH10K_MAC_FIRST_OFDM_RATE_IDX) |
| #define ath10k_a_rates_size (ARRAY_SIZE(ath10k_rates) - \ |
| ATH10K_MAC_FIRST_OFDM_RATE_IDX) |
| #define ath10k_g_rates (ath10k_rates + 0) |
| #define ath10k_g_rates_size (ARRAY_SIZE(ath10k_rates)) |
| |
| #define ath10k_g_rates_rev2 (ath10k_rates_rev2 + 0) |
| #define ath10k_g_rates_rev2_size (ARRAY_SIZE(ath10k_rates_rev2)) |
| |
| #define ath10k_wmi_legacy_rates ath10k_rates |
| |
| static bool ath10k_mac_bitrate_is_cck(int bitrate) |
| { |
| switch (bitrate) { |
| case 10: |
| case 20: |
| case 55: |
| case 110: |
| return true; |
| } |
| |
| return false; |
| } |
| |
| static u8 ath10k_mac_bitrate_to_rate(int bitrate) |
| { |
| return DIV_ROUND_UP(bitrate, 5) | |
| (ath10k_mac_bitrate_is_cck(bitrate) ? BIT(7) : 0); |
| } |
| |
| u8 ath10k_mac_hw_rate_to_idx(const struct ieee80211_supported_band *sband, |
| u8 hw_rate, bool cck) |
| { |
| const struct ieee80211_rate *rate; |
| int i; |
| |
| for (i = 0; i < sband->n_bitrates; i++) { |
| rate = &sband->bitrates[i]; |
| |
| if (ath10k_mac_bitrate_is_cck(rate->bitrate) != cck) |
| continue; |
| |
| if (rate->hw_value == hw_rate) |
| return i; |
| else if (rate->flags & IEEE80211_RATE_SHORT_PREAMBLE && |
| rate->hw_value_short == hw_rate) |
| return i; |
| } |
| |
| return 0; |
| } |
| |
| u8 ath10k_mac_bitrate_to_idx(const struct ieee80211_supported_band *sband, |
| u32 bitrate) |
| { |
| int i; |
| |
| for (i = 0; i < sband->n_bitrates; i++) |
| if (sband->bitrates[i].bitrate == bitrate) |
| return i; |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_get_rate_hw_value(int bitrate) |
| { |
| int i; |
| u8 hw_value_prefix = 0; |
| |
| if (ath10k_mac_bitrate_is_cck(bitrate)) |
| hw_value_prefix = WMI_RATE_PREAMBLE_CCK << 6; |
| |
| for (i = 0; i < ARRAY_SIZE(ath10k_rates); i++) { |
| if (ath10k_rates[i].bitrate == bitrate) |
| return hw_value_prefix | ath10k_rates[i].hw_value; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int ath10k_mac_get_max_vht_mcs_map(u16 mcs_map, int nss) |
| { |
| switch ((mcs_map >> (2 * nss)) & 0x3) { |
| case IEEE80211_VHT_MCS_SUPPORT_0_7: return BIT(8) - 1; |
| case IEEE80211_VHT_MCS_SUPPORT_0_8: return BIT(9) - 1; |
| case IEEE80211_VHT_MCS_SUPPORT_0_9: return BIT(10) - 1; |
| } |
| return 0; |
| } |
| |
| static u32 |
| ath10k_mac_max_ht_nss(const u8 ht_mcs_mask[IEEE80211_HT_MCS_MASK_LEN]) |
| { |
| int nss; |
| |
| for (nss = IEEE80211_HT_MCS_MASK_LEN - 1; nss >= 0; nss--) |
| if (ht_mcs_mask[nss]) |
| return nss + 1; |
| |
| return 1; |
| } |
| |
| static u32 |
| ath10k_mac_max_vht_nss(const u16 vht_mcs_mask[NL80211_VHT_NSS_MAX]) |
| { |
| int nss; |
| |
| for (nss = NL80211_VHT_NSS_MAX - 1; nss >= 0; nss--) |
| if (vht_mcs_mask[nss]) |
| return nss + 1; |
| |
| return 1; |
| } |
| |
| int ath10k_mac_ext_resource_config(struct ath10k *ar, u32 val) |
| { |
| enum wmi_host_platform_type platform_type; |
| int ret; |
| |
| if (test_bit(WMI_SERVICE_TX_MODE_DYNAMIC, ar->wmi.svc_map)) |
| platform_type = WMI_HOST_PLATFORM_LOW_PERF; |
| else |
| platform_type = WMI_HOST_PLATFORM_HIGH_PERF; |
| |
| ret = ath10k_wmi_ext_resource_config(ar, platform_type, val); |
| |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "failed to configure ext resource: %d\n", ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| /**********/ |
| /* Crypto */ |
| /**********/ |
| |
| static int ath10k_send_key(struct ath10k_vif *arvif, |
| struct ieee80211_key_conf *key, |
| enum set_key_cmd cmd, |
| const u8 *macaddr, u32 flags) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct wmi_vdev_install_key_arg arg = { |
| .vdev_id = arvif->vdev_id, |
| .key_idx = key->keyidx, |
| .key_len = key->keylen, |
| .key_data = key->key, |
| .key_flags = flags, |
| .macaddr = macaddr, |
| }; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| switch (key->cipher) { |
| case WLAN_CIPHER_SUITE_CCMP: |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_AES_CCM]; |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV_MGMT; |
| break; |
| case WLAN_CIPHER_SUITE_TKIP: |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_TKIP]; |
| arg.key_txmic_len = 8; |
| arg.key_rxmic_len = 8; |
| break; |
| case WLAN_CIPHER_SUITE_WEP40: |
| case WLAN_CIPHER_SUITE_WEP104: |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_WEP]; |
| break; |
| case WLAN_CIPHER_SUITE_CCMP_256: |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_AES_CCM]; |
| break; |
| case WLAN_CIPHER_SUITE_GCMP: |
| case WLAN_CIPHER_SUITE_GCMP_256: |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_AES_GCM]; |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV_MGMT; |
| break; |
| case WLAN_CIPHER_SUITE_BIP_GMAC_128: |
| case WLAN_CIPHER_SUITE_BIP_GMAC_256: |
| case WLAN_CIPHER_SUITE_BIP_CMAC_256: |
| case WLAN_CIPHER_SUITE_AES_CMAC: |
| WARN_ON(1); |
| return -EINVAL; |
| default: |
| ath10k_warn(ar, "cipher %d is not supported\n", key->cipher); |
| return -EOPNOTSUPP; |
| } |
| |
| if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) |
| key->flags |= IEEE80211_KEY_FLAG_GENERATE_IV; |
| |
| if (cmd == DISABLE_KEY) { |
| arg.key_cipher = ar->wmi_key_cipher[WMI_CIPHER_NONE]; |
| arg.key_data = NULL; |
| } |
| |
| return ath10k_wmi_vdev_install_key(arvif->ar, &arg); |
| } |
| |
| static int ath10k_install_key(struct ath10k_vif *arvif, |
| struct ieee80211_key_conf *key, |
| enum set_key_cmd cmd, |
| const u8 *macaddr, u32 flags) |
| { |
| struct ath10k *ar = arvif->ar; |
| int ret; |
| unsigned long time_left; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| reinit_completion(&ar->install_key_done); |
| |
| if (arvif->nohwcrypt) |
| return 1; |
| |
| ret = ath10k_send_key(arvif, key, cmd, macaddr, flags); |
| if (ret) |
| return ret; |
| |
| time_left = wait_for_completion_timeout(&ar->install_key_done, 3 * HZ); |
| if (time_left == 0) |
| return -ETIMEDOUT; |
| |
| return 0; |
| } |
| |
| static int ath10k_install_peer_wep_keys(struct ath10k_vif *arvif, |
| const u8 *addr) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ath10k_peer *peer; |
| int ret; |
| int i; |
| u32 flags; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (WARN_ON(arvif->vif->type != NL80211_IFTYPE_AP && |
| arvif->vif->type != NL80211_IFTYPE_ADHOC && |
| arvif->vif->type != NL80211_IFTYPE_MESH_POINT)) |
| return -EINVAL; |
| |
| spin_lock_bh(&ar->data_lock); |
| peer = ath10k_peer_find(ar, arvif->vdev_id, addr); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (!peer) |
| return -ENOENT; |
| |
| for (i = 0; i < ARRAY_SIZE(arvif->wep_keys); i++) { |
| if (arvif->wep_keys[i] == NULL) |
| continue; |
| |
| switch (arvif->vif->type) { |
| case NL80211_IFTYPE_AP: |
| flags = WMI_KEY_PAIRWISE; |
| |
| if (arvif->def_wep_key_idx == i) |
| flags |= WMI_KEY_TX_USAGE; |
| |
| ret = ath10k_install_key(arvif, arvif->wep_keys[i], |
| SET_KEY, addr, flags); |
| if (ret < 0) |
| return ret; |
| break; |
| case NL80211_IFTYPE_ADHOC: |
| ret = ath10k_install_key(arvif, arvif->wep_keys[i], |
| SET_KEY, addr, |
| WMI_KEY_PAIRWISE); |
| if (ret < 0) |
| return ret; |
| |
| ret = ath10k_install_key(arvif, arvif->wep_keys[i], |
| SET_KEY, addr, WMI_KEY_GROUP); |
| if (ret < 0) |
| return ret; |
| break; |
| default: |
| WARN_ON(1); |
| return -EINVAL; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| peer->keys[i] = arvif->wep_keys[i]; |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| /* In some cases (notably with static WEP IBSS with multiple keys) |
| * multicast Tx becomes broken. Both pairwise and groupwise keys are |
| * installed already. Using WMI_KEY_TX_USAGE in different combinations |
| * didn't seem help. Using def_keyid vdev parameter seems to be |
| * effective so use that. |
| * |
| * FIXME: Revisit. Perhaps this can be done in a less hacky way. |
| */ |
| if (arvif->vif->type != NL80211_IFTYPE_ADHOC) |
| return 0; |
| |
| if (arvif->def_wep_key_idx == -1) |
| return 0; |
| |
| ret = ath10k_wmi_vdev_set_param(arvif->ar, |
| arvif->vdev_id, |
| arvif->ar->wmi.vdev_param->def_keyid, |
| arvif->def_wep_key_idx); |
| if (ret) { |
| ath10k_warn(ar, "failed to re-set def wpa key idxon vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_clear_peer_keys(struct ath10k_vif *arvif, |
| const u8 *addr) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ath10k_peer *peer; |
| int first_errno = 0; |
| int ret; |
| int i; |
| u32 flags = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| peer = ath10k_peer_find(ar, arvif->vdev_id, addr); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (!peer) |
| return -ENOENT; |
| |
| for (i = 0; i < ARRAY_SIZE(peer->keys); i++) { |
| if (peer->keys[i] == NULL) |
| continue; |
| |
| /* key flags are not required to delete the key */ |
| ret = ath10k_install_key(arvif, peer->keys[i], |
| DISABLE_KEY, addr, flags); |
| if (ret < 0 && first_errno == 0) |
| first_errno = ret; |
| |
| if (ret < 0) |
| ath10k_warn(ar, "failed to remove peer wep key %d: %d\n", |
| i, ret); |
| |
| spin_lock_bh(&ar->data_lock); |
| peer->keys[i] = NULL; |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| return first_errno; |
| } |
| |
| bool ath10k_mac_is_peer_wep_key_set(struct ath10k *ar, const u8 *addr, |
| u8 keyidx) |
| { |
| struct ath10k_peer *peer; |
| int i; |
| |
| lockdep_assert_held(&ar->data_lock); |
| |
| /* We don't know which vdev this peer belongs to, |
| * since WMI doesn't give us that information. |
| * |
| * FIXME: multi-bss needs to be handled. |
| */ |
| peer = ath10k_peer_find(ar, 0, addr); |
| if (!peer) |
| return false; |
| |
| for (i = 0; i < ARRAY_SIZE(peer->keys); i++) { |
| if (peer->keys[i] && peer->keys[i]->keyidx == keyidx) |
| return true; |
| } |
| |
| return false; |
| } |
| |
| static int ath10k_clear_vdev_key(struct ath10k_vif *arvif, |
| struct ieee80211_key_conf *key) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ath10k_peer *peer; |
| u8 addr[ETH_ALEN]; |
| int first_errno = 0; |
| int ret; |
| int i; |
| u32 flags = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| for (;;) { |
| /* since ath10k_install_key we can't hold data_lock all the |
| * time, so we try to remove the keys incrementally |
| */ |
| spin_lock_bh(&ar->data_lock); |
| i = 0; |
| list_for_each_entry(peer, &ar->peers, list) { |
| for (i = 0; i < ARRAY_SIZE(peer->keys); i++) { |
| if (peer->keys[i] == key) { |
| ether_addr_copy(addr, peer->addr); |
| peer->keys[i] = NULL; |
| break; |
| } |
| } |
| |
| if (i < ARRAY_SIZE(peer->keys)) |
| break; |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (i == ARRAY_SIZE(peer->keys)) |
| break; |
| /* key flags are not required to delete the key */ |
| ret = ath10k_install_key(arvif, key, DISABLE_KEY, addr, flags); |
| if (ret < 0 && first_errno == 0) |
| first_errno = ret; |
| |
| if (ret) |
| ath10k_warn(ar, "failed to remove key for %pM: %d\n", |
| addr, ret); |
| } |
| |
| return first_errno; |
| } |
| |
| static int ath10k_mac_vif_update_wep_key(struct ath10k_vif *arvif, |
| struct ieee80211_key_conf *key) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ath10k_peer *peer; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| list_for_each_entry(peer, &ar->peers, list) { |
| if (ether_addr_equal(peer->addr, arvif->vif->addr)) |
| continue; |
| |
| if (ether_addr_equal(peer->addr, arvif->bssid)) |
| continue; |
| |
| if (peer->keys[key->keyidx] == key) |
| continue; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vif vdev %i update key %i needs update\n", |
| arvif->vdev_id, key->keyidx); |
| |
| ret = ath10k_install_peer_wep_keys(arvif, peer->addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to update wep keys on vdev %i for peer %pM: %d\n", |
| arvif->vdev_id, peer->addr, ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| /*********************/ |
| /* General utilities */ |
| /*********************/ |
| |
| static inline enum wmi_phy_mode |
| chan_to_phymode(const struct cfg80211_chan_def *chandef) |
| { |
| enum wmi_phy_mode phymode = MODE_UNKNOWN; |
| |
| switch (chandef->chan->band) { |
| case NL80211_BAND_2GHZ: |
| switch (chandef->width) { |
| case NL80211_CHAN_WIDTH_20_NOHT: |
| if (chandef->chan->flags & IEEE80211_CHAN_NO_OFDM) |
| phymode = MODE_11B; |
| else |
| phymode = MODE_11G; |
| break; |
| case NL80211_CHAN_WIDTH_20: |
| phymode = MODE_11NG_HT20; |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| phymode = MODE_11NG_HT40; |
| break; |
| default: |
| phymode = MODE_UNKNOWN; |
| break; |
| } |
| break; |
| case NL80211_BAND_5GHZ: |
| switch (chandef->width) { |
| case NL80211_CHAN_WIDTH_20_NOHT: |
| phymode = MODE_11A; |
| break; |
| case NL80211_CHAN_WIDTH_20: |
| phymode = MODE_11NA_HT20; |
| break; |
| case NL80211_CHAN_WIDTH_40: |
| phymode = MODE_11NA_HT40; |
| break; |
| case NL80211_CHAN_WIDTH_80: |
| phymode = MODE_11AC_VHT80; |
| break; |
| case NL80211_CHAN_WIDTH_160: |
| phymode = MODE_11AC_VHT160; |
| break; |
| case NL80211_CHAN_WIDTH_80P80: |
| phymode = MODE_11AC_VHT80_80; |
| break; |
| default: |
| phymode = MODE_UNKNOWN; |
| break; |
| } |
| break; |
| default: |
| break; |
| } |
| |
| WARN_ON(phymode == MODE_UNKNOWN); |
| return phymode; |
| } |
| |
| static u8 ath10k_parse_mpdudensity(u8 mpdudensity) |
| { |
| /* |
| * 802.11n D2.0 defined values for "Minimum MPDU Start Spacing": |
| * 0 for no restriction |
| * 1 for 1/4 us |
| * 2 for 1/2 us |
| * 3 for 1 us |
| * 4 for 2 us |
| * 5 for 4 us |
| * 6 for 8 us |
| * 7 for 16 us |
| */ |
| switch (mpdudensity) { |
| case 0: |
| return 0; |
| case 1: |
| case 2: |
| case 3: |
| /* Our lower layer calculations limit our precision to |
| * 1 microsecond |
| */ |
| return 1; |
| case 4: |
| return 2; |
| case 5: |
| return 4; |
| case 6: |
| return 8; |
| case 7: |
| return 16; |
| default: |
| return 0; |
| } |
| } |
| |
| int ath10k_mac_vif_chan(struct ieee80211_vif *vif, |
| struct cfg80211_chan_def *def) |
| { |
| struct ieee80211_chanctx_conf *conf; |
| |
| rcu_read_lock(); |
| conf = rcu_dereference(vif->bss_conf.chanctx_conf); |
| if (!conf) { |
| rcu_read_unlock(); |
| return -ENOENT; |
| } |
| |
| *def = conf->def; |
| rcu_read_unlock(); |
| |
| return 0; |
| } |
| |
| static void ath10k_mac_num_chanctxs_iter(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *conf, |
| void *data) |
| { |
| int *num = data; |
| |
| (*num)++; |
| } |
| |
| static int ath10k_mac_num_chanctxs(struct ath10k *ar) |
| { |
| int num = 0; |
| |
| ieee80211_iter_chan_contexts_atomic(ar->hw, |
| ath10k_mac_num_chanctxs_iter, |
| &num); |
| |
| return num; |
| } |
| |
| static void |
| ath10k_mac_get_any_chandef_iter(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *conf, |
| void *data) |
| { |
| struct cfg80211_chan_def **def = data; |
| |
| *def = &conf->def; |
| } |
| |
| static void ath10k_wait_for_peer_delete_done(struct ath10k *ar, u32 vdev_id, |
| const u8 *addr) |
| { |
| unsigned long time_left; |
| int ret; |
| |
| if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) { |
| ret = ath10k_wait_for_peer_deleted(ar, vdev_id, addr); |
| if (ret) { |
| ath10k_warn(ar, "failed wait for peer deleted"); |
| return; |
| } |
| |
| time_left = wait_for_completion_timeout(&ar->peer_delete_done, |
| 5 * HZ); |
| if (!time_left) |
| ath10k_warn(ar, "Timeout in receiving peer delete response\n"); |
| } |
| } |
| |
| static int ath10k_peer_create(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| u32 vdev_id, |
| const u8 *addr, |
| enum wmi_peer_type peer_type) |
| { |
| struct ath10k_peer *peer; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| /* Each vdev consumes a peer entry as well. */ |
| if (ar->num_peers + list_count_nodes(&ar->arvifs) >= ar->max_num_peers) |
| return -ENOBUFS; |
| |
| ret = ath10k_wmi_peer_create(ar, vdev_id, addr, peer_type); |
| if (ret) { |
| ath10k_warn(ar, "failed to create wmi peer %pM on vdev %i: %i\n", |
| addr, vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_wait_for_peer_created(ar, vdev_id, addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to wait for created wmi peer %pM on vdev %i: %i\n", |
| addr, vdev_id, ret); |
| return ret; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| peer = ath10k_peer_find(ar, vdev_id, addr); |
| if (!peer) { |
| spin_unlock_bh(&ar->data_lock); |
| ath10k_warn(ar, "failed to find peer %pM on vdev %i after creation\n", |
| addr, vdev_id); |
| ath10k_wait_for_peer_delete_done(ar, vdev_id, addr); |
| return -ENOENT; |
| } |
| |
| peer->vif = vif; |
| peer->sta = sta; |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| ar->num_peers++; |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_set_kickout(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 param; |
| int ret; |
| |
| param = ar->wmi.pdev_param->sta_kickout_th; |
| ret = ath10k_wmi_pdev_set_param(ar, param, |
| ATH10K_KICKOUT_THRESHOLD); |
| if (ret) { |
| ath10k_warn(ar, "failed to set kickout threshold on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| param = ar->wmi.vdev_param->ap_keepalive_min_idle_inactive_time_secs; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param, |
| ATH10K_KEEPALIVE_MIN_IDLE); |
| if (ret) { |
| ath10k_warn(ar, "failed to set keepalive minimum idle time on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| param = ar->wmi.vdev_param->ap_keepalive_max_idle_inactive_time_secs; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param, |
| ATH10K_KEEPALIVE_MAX_IDLE); |
| if (ret) { |
| ath10k_warn(ar, "failed to set keepalive maximum idle time on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| param = ar->wmi.vdev_param->ap_keepalive_max_unresponsive_time_secs; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param, |
| ATH10K_KEEPALIVE_MAX_UNRESPONSIVE); |
| if (ret) { |
| ath10k_warn(ar, "failed to set keepalive maximum unresponsive time on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_set_rts(struct ath10k_vif *arvif, u32 value) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 vdev_param; |
| |
| vdev_param = ar->wmi.vdev_param->rts_threshold; |
| return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, value); |
| } |
| |
| static int ath10k_peer_delete(struct ath10k *ar, u32 vdev_id, const u8 *addr) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_peer_delete(ar, vdev_id, addr); |
| if (ret) |
| return ret; |
| |
| ret = ath10k_wait_for_peer_deleted(ar, vdev_id, addr); |
| if (ret) |
| return ret; |
| |
| if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) { |
| unsigned long time_left; |
| |
| time_left = wait_for_completion_timeout |
| (&ar->peer_delete_done, 5 * HZ); |
| |
| if (!time_left) { |
| ath10k_warn(ar, "Timeout in receiving peer delete response\n"); |
| return -ETIMEDOUT; |
| } |
| } |
| |
| ar->num_peers--; |
| |
| return 0; |
| } |
| |
| static void ath10k_peer_map_cleanup(struct ath10k *ar, struct ath10k_peer *peer) |
| { |
| int peer_id, i; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| for_each_set_bit(peer_id, peer->peer_ids, |
| ATH10K_MAX_NUM_PEER_IDS) { |
| ar->peer_map[peer_id] = NULL; |
| } |
| |
| /* Double check that peer is properly un-referenced from |
| * the peer_map |
| */ |
| for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) { |
| if (ar->peer_map[i] == peer) { |
| ath10k_warn(ar, "removing stale peer_map entry for %pM (ptr %pK idx %d)\n", |
| peer->addr, peer, i); |
| ar->peer_map[i] = NULL; |
| } |
| } |
| |
| list_del(&peer->list); |
| kfree(peer); |
| ar->num_peers--; |
| } |
| |
| static void ath10k_peer_cleanup(struct ath10k *ar, u32 vdev_id) |
| { |
| struct ath10k_peer *peer, *tmp; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| list_for_each_entry_safe(peer, tmp, &ar->peers, list) { |
| if (peer->vdev_id != vdev_id) |
| continue; |
| |
| ath10k_warn(ar, "removing stale peer %pM from vdev_id %d\n", |
| peer->addr, vdev_id); |
| |
| ath10k_peer_map_cleanup(ar, peer); |
| } |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| static void ath10k_peer_cleanup_all(struct ath10k *ar) |
| { |
| struct ath10k_peer *peer, *tmp; |
| int i; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| list_for_each_entry_safe(peer, tmp, &ar->peers, list) { |
| list_del(&peer->list); |
| kfree(peer); |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) |
| ar->peer_map[i] = NULL; |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| ar->num_peers = 0; |
| ar->num_stations = 0; |
| } |
| |
| static int ath10k_mac_tdls_peer_update(struct ath10k *ar, u32 vdev_id, |
| struct ieee80211_sta *sta, |
| enum wmi_tdls_peer_state state) |
| { |
| int ret; |
| struct wmi_tdls_peer_update_cmd_arg arg = {}; |
| struct wmi_tdls_peer_capab_arg cap = {}; |
| struct wmi_channel_arg chan_arg = {}; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| arg.vdev_id = vdev_id; |
| arg.peer_state = state; |
| ether_addr_copy(arg.addr, sta->addr); |
| |
| cap.peer_max_sp = sta->max_sp; |
| cap.peer_uapsd_queues = sta->uapsd_queues; |
| |
| if (state == WMI_TDLS_PEER_STATE_CONNECTED && |
| !sta->tdls_initiator) |
| cap.is_peer_responder = 1; |
| |
| ret = ath10k_wmi_tdls_peer_update(ar, &arg, &cap, &chan_arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to update tdls peer %pM on vdev %i: %i\n", |
| arg.addr, vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| /************************/ |
| /* Interface management */ |
| /************************/ |
| |
| void ath10k_mac_vif_beacon_free(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->data_lock); |
| |
| if (!arvif->beacon) |
| return; |
| |
| if (!arvif->beacon_buf) |
| dma_unmap_single(ar->dev, ATH10K_SKB_CB(arvif->beacon)->paddr, |
| arvif->beacon->len, DMA_TO_DEVICE); |
| |
| if (WARN_ON(arvif->beacon_state != ATH10K_BEACON_SCHEDULED && |
| arvif->beacon_state != ATH10K_BEACON_SENT)) |
| return; |
| |
| dev_kfree_skb_any(arvif->beacon); |
| |
| arvif->beacon = NULL; |
| arvif->beacon_state = ATH10K_BEACON_SCHEDULED; |
| } |
| |
| static void ath10k_mac_vif_beacon_cleanup(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->data_lock); |
| |
| ath10k_mac_vif_beacon_free(arvif); |
| |
| if (arvif->beacon_buf) { |
| if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL) |
| kfree(arvif->beacon_buf); |
| else |
| dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN, |
| arvif->beacon_buf, |
| arvif->beacon_paddr); |
| arvif->beacon_buf = NULL; |
| } |
| } |
| |
| static inline int ath10k_vdev_setup_sync(struct ath10k *ar) |
| { |
| unsigned long time_left; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (test_bit(ATH10K_FLAG_CRASH_FLUSH, &ar->dev_flags)) |
| return -ESHUTDOWN; |
| |
| time_left = wait_for_completion_timeout(&ar->vdev_setup_done, |
| ATH10K_VDEV_SETUP_TIMEOUT_HZ); |
| if (time_left == 0) |
| return -ETIMEDOUT; |
| |
| return ar->last_wmi_vdev_start_status; |
| } |
| |
| static int ath10k_monitor_vdev_start(struct ath10k *ar, int vdev_id) |
| { |
| struct cfg80211_chan_def *chandef = NULL; |
| struct ieee80211_channel *channel = NULL; |
| struct wmi_vdev_start_request_arg arg = {}; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ieee80211_iter_chan_contexts_atomic(ar->hw, |
| ath10k_mac_get_any_chandef_iter, |
| &chandef); |
| if (WARN_ON_ONCE(!chandef)) |
| return -ENOENT; |
| |
| channel = chandef->chan; |
| |
| arg.vdev_id = vdev_id; |
| arg.channel.freq = channel->center_freq; |
| arg.channel.band_center_freq1 = chandef->center_freq1; |
| arg.channel.band_center_freq2 = chandef->center_freq2; |
| |
| /* TODO setup this dynamically, what in case we |
| * don't have any vifs? |
| */ |
| arg.channel.mode = chan_to_phymode(chandef); |
| arg.channel.chan_radar = |
| !!(channel->flags & IEEE80211_CHAN_RADAR); |
| |
| arg.channel.min_power = 0; |
| arg.channel.max_power = channel->max_power * 2; |
| arg.channel.max_reg_power = channel->max_reg_power * 2; |
| arg.channel.max_antenna_gain = channel->max_antenna_gain; |
| |
| reinit_completion(&ar->vdev_setup_done); |
| reinit_completion(&ar->vdev_delete_done); |
| |
| ret = ath10k_wmi_vdev_start(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to request monitor vdev %i start: %d\n", |
| vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_vdev_setup_sync(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to synchronize setup for monitor vdev %i start: %d\n", |
| vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_wmi_vdev_up(ar, vdev_id, 0, ar->mac_addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to put up monitor vdev %i: %d\n", |
| vdev_id, ret); |
| goto vdev_stop; |
| } |
| |
| ar->monitor_vdev_id = vdev_id; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %i started\n", |
| ar->monitor_vdev_id); |
| return 0; |
| |
| vdev_stop: |
| ret = ath10k_wmi_vdev_stop(ar, ar->monitor_vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to stop monitor vdev %i after start failure: %d\n", |
| ar->monitor_vdev_id, ret); |
| |
| return ret; |
| } |
| |
| static int ath10k_monitor_vdev_stop(struct ath10k *ar) |
| { |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_vdev_down(ar, ar->monitor_vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to put down monitor vdev %i: %d\n", |
| ar->monitor_vdev_id, ret); |
| |
| reinit_completion(&ar->vdev_setup_done); |
| reinit_completion(&ar->vdev_delete_done); |
| |
| ret = ath10k_wmi_vdev_stop(ar, ar->monitor_vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to request monitor vdev %i stop: %d\n", |
| ar->monitor_vdev_id, ret); |
| |
| ret = ath10k_vdev_setup_sync(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to synchronize monitor vdev %i stop: %d\n", |
| ar->monitor_vdev_id, ret); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %i stopped\n", |
| ar->monitor_vdev_id); |
| return ret; |
| } |
| |
| static int ath10k_monitor_vdev_create(struct ath10k *ar) |
| { |
| int bit, ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (ar->free_vdev_map == 0) { |
| ath10k_warn(ar, "failed to find free vdev id for monitor vdev\n"); |
| return -ENOMEM; |
| } |
| |
| bit = __ffs64(ar->free_vdev_map); |
| |
| ar->monitor_vdev_id = bit; |
| |
| ret = ath10k_wmi_vdev_create(ar, ar->monitor_vdev_id, |
| WMI_VDEV_TYPE_MONITOR, |
| 0, ar->mac_addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to request monitor vdev %i creation: %d\n", |
| ar->monitor_vdev_id, ret); |
| return ret; |
| } |
| |
| ar->free_vdev_map &= ~(1LL << ar->monitor_vdev_id); |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %d created\n", |
| ar->monitor_vdev_id); |
| |
| return 0; |
| } |
| |
| static int ath10k_monitor_vdev_delete(struct ath10k *ar) |
| { |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_vdev_delete(ar, ar->monitor_vdev_id); |
| if (ret) { |
| ath10k_warn(ar, "failed to request wmi monitor vdev %i removal: %d\n", |
| ar->monitor_vdev_id, ret); |
| return ret; |
| } |
| |
| ar->free_vdev_map |= 1LL << ar->monitor_vdev_id; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor vdev %d deleted\n", |
| ar->monitor_vdev_id); |
| return ret; |
| } |
| |
| static int ath10k_monitor_start(struct ath10k *ar) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_monitor_vdev_create(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to create monitor vdev: %d\n", ret); |
| return ret; |
| } |
| |
| ret = ath10k_monitor_vdev_start(ar, ar->monitor_vdev_id); |
| if (ret) { |
| ath10k_warn(ar, "failed to start monitor vdev: %d\n", ret); |
| ath10k_monitor_vdev_delete(ar); |
| return ret; |
| } |
| |
| ar->monitor_started = true; |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor started\n"); |
| |
| return 0; |
| } |
| |
| static int ath10k_monitor_stop(struct ath10k *ar) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_monitor_vdev_stop(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to stop monitor vdev: %d\n", ret); |
| return ret; |
| } |
| |
| ret = ath10k_monitor_vdev_delete(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to delete monitor vdev: %d\n", ret); |
| return ret; |
| } |
| |
| ar->monitor_started = false; |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor stopped\n"); |
| |
| return 0; |
| } |
| |
| static bool ath10k_mac_monitor_vdev_is_needed(struct ath10k *ar) |
| { |
| int num_ctx; |
| |
| /* At least one chanctx is required to derive a channel to start |
| * monitor vdev on. |
| */ |
| num_ctx = ath10k_mac_num_chanctxs(ar); |
| if (num_ctx == 0) |
| return false; |
| |
| /* If there's already an existing special monitor interface then don't |
| * bother creating another monitor vdev. |
| */ |
| if (ar->monitor_arvif) |
| return false; |
| |
| return ar->monitor || |
| (!test_bit(ATH10K_FW_FEATURE_ALLOWS_MESH_BCAST, |
| ar->running_fw->fw_file.fw_features) && |
| (ar->filter_flags & (FIF_OTHER_BSS | FIF_MCAST_ACTION))) || |
| test_bit(ATH10K_CAC_RUNNING, &ar->dev_flags); |
| } |
| |
| static bool ath10k_mac_monitor_vdev_is_allowed(struct ath10k *ar) |
| { |
| int num_ctx; |
| |
| num_ctx = ath10k_mac_num_chanctxs(ar); |
| |
| /* FIXME: Current interface combinations and cfg80211/mac80211 code |
| * shouldn't allow this but make sure to prevent handling the following |
| * case anyway since multi-channel DFS hasn't been tested at all. |
| */ |
| if (test_bit(ATH10K_CAC_RUNNING, &ar->dev_flags) && num_ctx > 1) |
| return false; |
| |
| return true; |
| } |
| |
| static int ath10k_monitor_recalc(struct ath10k *ar) |
| { |
| bool needed; |
| bool allowed; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| needed = ath10k_mac_monitor_vdev_is_needed(ar); |
| allowed = ath10k_mac_monitor_vdev_is_allowed(ar); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac monitor recalc started? %d needed? %d allowed? %d\n", |
| ar->monitor_started, needed, allowed); |
| |
| if (WARN_ON(needed && !allowed)) { |
| if (ar->monitor_started) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac monitor stopping disallowed monitor\n"); |
| |
| ret = ath10k_monitor_stop(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to stop disallowed monitor: %d\n", |
| ret); |
| /* not serious */ |
| } |
| |
| return -EPERM; |
| } |
| |
| if (needed == ar->monitor_started) |
| return 0; |
| |
| if (needed) |
| return ath10k_monitor_start(ar); |
| else |
| return ath10k_monitor_stop(ar); |
| } |
| |
| static bool ath10k_mac_can_set_cts_prot(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (!arvif->is_started) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "defer cts setup, vdev is not ready yet\n"); |
| return false; |
| } |
| |
| return true; |
| } |
| |
| static int ath10k_mac_set_cts_prot(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 vdev_param; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| vdev_param = ar->wmi.vdev_param->protection_mode; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d cts_protection %d\n", |
| arvif->vdev_id, arvif->use_cts_prot); |
| |
| return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| arvif->use_cts_prot ? 1 : 0); |
| } |
| |
| static int ath10k_recalc_rtscts_prot(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 vdev_param, rts_cts = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| vdev_param = ar->wmi.vdev_param->enable_rtscts; |
| |
| rts_cts |= SM(WMI_RTSCTS_ENABLED, WMI_RTSCTS_SET); |
| |
| if (arvif->num_legacy_stations > 0) |
| rts_cts |= SM(WMI_RTSCTS_ACROSS_SW_RETRIES, |
| WMI_RTSCTS_PROFILE); |
| else |
| rts_cts |= SM(WMI_RTSCTS_FOR_SECOND_RATESERIES, |
| WMI_RTSCTS_PROFILE); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d recalc rts/cts prot %d\n", |
| arvif->vdev_id, rts_cts); |
| |
| return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| rts_cts); |
| } |
| |
| static int ath10k_start_cac(struct ath10k *ar) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| set_bit(ATH10K_CAC_RUNNING, &ar->dev_flags); |
| |
| ret = ath10k_monitor_recalc(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to start monitor (cac): %d\n", ret); |
| clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags); |
| return ret; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac cac start monitor vdev %d\n", |
| ar->monitor_vdev_id); |
| |
| return 0; |
| } |
| |
| static int ath10k_stop_cac(struct ath10k *ar) |
| { |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| /* CAC is not running - do nothing */ |
| if (!test_bit(ATH10K_CAC_RUNNING, &ar->dev_flags)) |
| return 0; |
| |
| clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags); |
| ath10k_monitor_stop(ar); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac cac finished\n"); |
| |
| return 0; |
| } |
| |
| static void ath10k_mac_has_radar_iter(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *conf, |
| void *data) |
| { |
| bool *ret = data; |
| |
| if (!*ret && conf->radar_enabled) |
| *ret = true; |
| } |
| |
| static bool ath10k_mac_has_radar_enabled(struct ath10k *ar) |
| { |
| bool has_radar = false; |
| |
| ieee80211_iter_chan_contexts_atomic(ar->hw, |
| ath10k_mac_has_radar_iter, |
| &has_radar); |
| |
| return has_radar; |
| } |
| |
| static void ath10k_recalc_radar_detection(struct ath10k *ar) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ath10k_stop_cac(ar); |
| |
| if (!ath10k_mac_has_radar_enabled(ar)) |
| return; |
| |
| if (ar->num_started_vdevs > 0) |
| return; |
| |
| ret = ath10k_start_cac(ar); |
| if (ret) { |
| /* |
| * Not possible to start CAC on current channel so starting |
| * radiation is not allowed, make this channel DFS_UNAVAILABLE |
| * by indicating that radar was detected. |
| */ |
| ath10k_warn(ar, "failed to start CAC: %d\n", ret); |
| ieee80211_radar_detected(ar->hw, NULL); |
| } |
| } |
| |
| static int ath10k_vdev_stop(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| reinit_completion(&ar->vdev_setup_done); |
| reinit_completion(&ar->vdev_delete_done); |
| |
| ret = ath10k_wmi_vdev_stop(ar, arvif->vdev_id); |
| if (ret) { |
| ath10k_warn(ar, "failed to stop WMI vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_vdev_setup_sync(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to synchronize setup for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| WARN_ON(ar->num_started_vdevs == 0); |
| |
| if (ar->num_started_vdevs != 0) { |
| ar->num_started_vdevs--; |
| ath10k_recalc_radar_detection(ar); |
| } |
| |
| return ret; |
| } |
| |
| static int ath10k_vdev_start_restart(struct ath10k_vif *arvif, |
| const struct cfg80211_chan_def *chandef, |
| bool restart) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct wmi_vdev_start_request_arg arg = {}; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| reinit_completion(&ar->vdev_setup_done); |
| reinit_completion(&ar->vdev_delete_done); |
| |
| arg.vdev_id = arvif->vdev_id; |
| arg.dtim_period = arvif->dtim_period; |
| arg.bcn_intval = arvif->beacon_interval; |
| |
| arg.channel.freq = chandef->chan->center_freq; |
| arg.channel.band_center_freq1 = chandef->center_freq1; |
| arg.channel.band_center_freq2 = chandef->center_freq2; |
| arg.channel.mode = chan_to_phymode(chandef); |
| |
| arg.channel.min_power = 0; |
| arg.channel.max_power = chandef->chan->max_power * 2; |
| arg.channel.max_reg_power = chandef->chan->max_reg_power * 2; |
| arg.channel.max_antenna_gain = chandef->chan->max_antenna_gain; |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP) { |
| arg.ssid = arvif->u.ap.ssid; |
| arg.ssid_len = arvif->u.ap.ssid_len; |
| arg.hidden_ssid = arvif->u.ap.hidden_ssid; |
| |
| /* For now allow DFS for AP mode */ |
| arg.channel.chan_radar = |
| !!(chandef->chan->flags & IEEE80211_CHAN_RADAR); |
| } else if (arvif->vdev_type == WMI_VDEV_TYPE_IBSS) { |
| arg.ssid = arvif->vif->cfg.ssid; |
| arg.ssid_len = arvif->vif->cfg.ssid_len; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d start center_freq %d phymode %s\n", |
| arg.vdev_id, arg.channel.freq, |
| ath10k_wmi_phymode_str(arg.channel.mode)); |
| |
| if (restart) |
| ret = ath10k_wmi_vdev_restart(ar, &arg); |
| else |
| ret = ath10k_wmi_vdev_start(ar, &arg); |
| |
| if (ret) { |
| ath10k_warn(ar, "failed to start WMI vdev %i: %d\n", |
| arg.vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_vdev_setup_sync(ar); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to synchronize setup for vdev %i restart %d: %d\n", |
| arg.vdev_id, restart, ret); |
| return ret; |
| } |
| |
| ar->num_started_vdevs++; |
| ath10k_recalc_radar_detection(ar); |
| |
| return ret; |
| } |
| |
| static int ath10k_vdev_start(struct ath10k_vif *arvif, |
| const struct cfg80211_chan_def *def) |
| { |
| return ath10k_vdev_start_restart(arvif, def, false); |
| } |
| |
| static int ath10k_vdev_restart(struct ath10k_vif *arvif, |
| const struct cfg80211_chan_def *def) |
| { |
| return ath10k_vdev_start_restart(arvif, def, true); |
| } |
| |
| static int ath10k_mac_setup_bcn_p2p_ie(struct ath10k_vif *arvif, |
| struct sk_buff *bcn) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_mgmt *mgmt; |
| const u8 *p2p_ie; |
| int ret; |
| |
| if (arvif->vif->type != NL80211_IFTYPE_AP || !arvif->vif->p2p) |
| return 0; |
| |
| mgmt = (void *)bcn->data; |
| p2p_ie = cfg80211_find_vendor_ie(WLAN_OUI_WFA, WLAN_OUI_TYPE_WFA_P2P, |
| mgmt->u.beacon.variable, |
| bcn->len - (mgmt->u.beacon.variable - |
| bcn->data)); |
| if (!p2p_ie) |
| return -ENOENT; |
| |
| ret = ath10k_wmi_p2p_go_bcn_ie(ar, arvif->vdev_id, p2p_ie); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit p2p go bcn ie for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_remove_vendor_ie(struct sk_buff *skb, unsigned int oui, |
| u8 oui_type, size_t ie_offset) |
| { |
| size_t len; |
| const u8 *next; |
| const u8 *end; |
| u8 *ie; |
| |
| if (WARN_ON(skb->len < ie_offset)) |
| return -EINVAL; |
| |
| ie = (u8 *)cfg80211_find_vendor_ie(oui, oui_type, |
| skb->data + ie_offset, |
| skb->len - ie_offset); |
| if (!ie) |
| return -ENOENT; |
| |
| len = ie[1] + 2; |
| end = skb->data + skb->len; |
| next = ie + len; |
| |
| if (WARN_ON(next > end)) |
| return -EINVAL; |
| |
| memmove(ie, next, end - next); |
| skb_trim(skb, skb->len - len); |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_setup_bcn_tmpl(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_hw *hw = ar->hw; |
| struct ieee80211_vif *vif = arvif->vif; |
| struct ieee80211_mutable_offsets offs = {}; |
| struct sk_buff *bcn; |
| int ret; |
| |
| if (!test_bit(WMI_SERVICE_BEACON_OFFLOAD, ar->wmi.svc_map)) |
| return 0; |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_AP && |
| arvif->vdev_type != WMI_VDEV_TYPE_IBSS) |
| return 0; |
| |
| bcn = ieee80211_beacon_get_template(hw, vif, &offs, 0); |
| if (!bcn) { |
| ath10k_warn(ar, "failed to get beacon template from mac80211\n"); |
| return -EPERM; |
| } |
| |
| ret = ath10k_mac_setup_bcn_p2p_ie(arvif, bcn); |
| if (ret) { |
| ath10k_warn(ar, "failed to setup p2p go bcn ie: %d\n", ret); |
| kfree_skb(bcn); |
| return ret; |
| } |
| |
| /* P2P IE is inserted by firmware automatically (as configured above) |
| * so remove it from the base beacon template to avoid duplicate P2P |
| * IEs in beacon frames. |
| */ |
| ath10k_mac_remove_vendor_ie(bcn, WLAN_OUI_WFA, WLAN_OUI_TYPE_WFA_P2P, |
| offsetof(struct ieee80211_mgmt, |
| u.beacon.variable)); |
| |
| ret = ath10k_wmi_bcn_tmpl(ar, arvif->vdev_id, offs.tim_offset, bcn, 0, |
| 0, NULL, 0); |
| kfree_skb(bcn); |
| |
| if (ret) { |
| ath10k_warn(ar, "failed to submit beacon template command: %d\n", |
| ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_setup_prb_tmpl(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_hw *hw = ar->hw; |
| struct ieee80211_vif *vif = arvif->vif; |
| struct sk_buff *prb; |
| int ret; |
| |
| if (!test_bit(WMI_SERVICE_BEACON_OFFLOAD, ar->wmi.svc_map)) |
| return 0; |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_AP) |
| return 0; |
| |
| /* For mesh, probe response and beacon share the same template */ |
| if (ieee80211_vif_is_mesh(vif)) |
| return 0; |
| |
| prb = ieee80211_proberesp_get(hw, vif); |
| if (!prb) { |
| ath10k_warn(ar, "failed to get probe resp template from mac80211\n"); |
| return -EPERM; |
| } |
| |
| ret = ath10k_wmi_prb_tmpl(ar, arvif->vdev_id, prb); |
| kfree_skb(prb); |
| |
| if (ret) { |
| ath10k_warn(ar, "failed to submit probe resp template command: %d\n", |
| ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_vif_fix_hidden_ssid(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct cfg80211_chan_def def; |
| int ret; |
| |
| /* When originally vdev is started during assign_vif_chanctx() some |
| * information is missing, notably SSID. Firmware revisions with beacon |
| * offloading require the SSID to be provided during vdev (re)start to |
| * handle hidden SSID properly. |
| * |
| * Vdev restart must be done after vdev has been both started and |
| * upped. Otherwise some firmware revisions (at least 10.2) fail to |
| * deliver vdev restart response event causing timeouts during vdev |
| * syncing in ath10k. |
| * |
| * Note: The vdev down/up and template reinstallation could be skipped |
| * since only wmi-tlv firmware are known to have beacon offload and |
| * wmi-tlv doesn't seem to misbehave like 10.2 wrt vdev restart |
| * response delivery. It's probably more robust to keep it as is. |
| */ |
| if (!test_bit(WMI_SERVICE_BEACON_OFFLOAD, ar->wmi.svc_map)) |
| return 0; |
| |
| if (WARN_ON(!arvif->is_started)) |
| return -EINVAL; |
| |
| if (WARN_ON(!arvif->is_up)) |
| return -EINVAL; |
| |
| if (WARN_ON(ath10k_mac_vif_chan(arvif->vif, &def))) |
| return -EINVAL; |
| |
| ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id); |
| if (ret) { |
| ath10k_warn(ar, "failed to bring down ap vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| /* Vdev down reset beacon & presp templates. Reinstall them. Otherwise |
| * firmware will crash upon vdev up. |
| */ |
| |
| ret = ath10k_mac_setup_bcn_tmpl(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to update beacon template: %d\n", ret); |
| return ret; |
| } |
| |
| ret = ath10k_mac_setup_prb_tmpl(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to update presp template: %d\n", ret); |
| return ret; |
| } |
| |
| ret = ath10k_vdev_restart(arvif, &def); |
| if (ret) { |
| ath10k_warn(ar, "failed to restart ap vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_wmi_vdev_up(arvif->ar, arvif->vdev_id, arvif->aid, |
| arvif->bssid); |
| if (ret) { |
| ath10k_warn(ar, "failed to bring up ap vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void ath10k_control_beaconing(struct ath10k_vif *arvif, |
| struct ieee80211_bss_conf *info) |
| { |
| struct ath10k *ar = arvif->ar; |
| int ret = 0; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (!info->enable_beacon) { |
| ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to down vdev_id %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| arvif->is_up = false; |
| |
| spin_lock_bh(&arvif->ar->data_lock); |
| ath10k_mac_vif_beacon_free(arvif); |
| spin_unlock_bh(&arvif->ar->data_lock); |
| |
| return; |
| } |
| |
| arvif->tx_seq_no = 0x1000; |
| |
| arvif->aid = 0; |
| ether_addr_copy(arvif->bssid, info->bssid); |
| |
| ret = ath10k_wmi_vdev_up(arvif->ar, arvif->vdev_id, arvif->aid, |
| arvif->bssid); |
| if (ret) { |
| ath10k_warn(ar, "failed to bring up vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| return; |
| } |
| |
| arvif->is_up = true; |
| |
| ret = ath10k_mac_vif_fix_hidden_ssid(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to fix hidden ssid for vdev %i, expect trouble: %d\n", |
| arvif->vdev_id, ret); |
| return; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d up\n", arvif->vdev_id); |
| } |
| |
| static void ath10k_control_ibss(struct ath10k_vif *arvif, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 vdev_param; |
| int ret = 0; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (!vif->cfg.ibss_joined) { |
| if (is_zero_ether_addr(arvif->bssid)) |
| return; |
| |
| eth_zero_addr(arvif->bssid); |
| |
| return; |
| } |
| |
| vdev_param = arvif->ar->wmi.vdev_param->atim_window; |
| ret = ath10k_wmi_vdev_set_param(arvif->ar, arvif->vdev_id, vdev_param, |
| ATH10K_DEFAULT_ATIM); |
| if (ret) |
| ath10k_warn(ar, "failed to set IBSS ATIM for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| static int ath10k_mac_vif_recalc_ps_wake_threshold(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 param; |
| u32 value; |
| int ret; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (arvif->u.sta.uapsd) |
| value = WMI_STA_PS_TX_WAKE_THRESHOLD_NEVER; |
| else |
| value = WMI_STA_PS_TX_WAKE_THRESHOLD_ALWAYS; |
| |
| param = WMI_STA_PS_PARAM_TX_WAKE_THRESHOLD; |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param, value); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit ps wake threshold %u on vdev %i: %d\n", |
| value, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_vif_recalc_ps_poll_count(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 param; |
| u32 value; |
| int ret; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (arvif->u.sta.uapsd) |
| value = WMI_STA_PS_PSPOLL_COUNT_UAPSD; |
| else |
| value = WMI_STA_PS_PSPOLL_COUNT_NO_MAX; |
| |
| param = WMI_STA_PS_PARAM_PSPOLL_COUNT; |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, |
| param, value); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit ps poll count %u on vdev %i: %d\n", |
| value, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_num_vifs_started(struct ath10k *ar) |
| { |
| struct ath10k_vif *arvif; |
| int num = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| list_for_each_entry(arvif, &ar->arvifs, list) |
| if (arvif->is_started) |
| num++; |
| |
| return num; |
| } |
| |
| static int ath10k_mac_vif_setup_ps(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_vif *vif = arvif->vif; |
| struct ieee80211_conf *conf = &ar->hw->conf; |
| enum wmi_sta_powersave_param param; |
| enum wmi_sta_ps_mode psmode; |
| int ret; |
| int ps_timeout; |
| bool enable_ps; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (arvif->vif->type != NL80211_IFTYPE_STATION) |
| return 0; |
| |
| enable_ps = arvif->ps; |
| |
| if (enable_ps && ath10k_mac_num_vifs_started(ar) > 1 && |
| !test_bit(ATH10K_FW_FEATURE_MULTI_VIF_PS_SUPPORT, |
| ar->running_fw->fw_file.fw_features)) { |
| ath10k_warn(ar, "refusing to enable ps on vdev %i: not supported by fw\n", |
| arvif->vdev_id); |
| enable_ps = false; |
| } |
| |
| if (!arvif->is_started) { |
| /* mac80211 can update vif powersave state while disconnected. |
| * Firmware doesn't behave nicely and consumes more power than |
| * necessary if PS is disabled on a non-started vdev. Hence |
| * force-enable PS for non-running vdevs. |
| */ |
| psmode = WMI_STA_PS_MODE_ENABLED; |
| } else if (enable_ps) { |
| psmode = WMI_STA_PS_MODE_ENABLED; |
| param = WMI_STA_PS_PARAM_INACTIVITY_TIME; |
| |
| ps_timeout = conf->dynamic_ps_timeout; |
| if (ps_timeout == 0) { |
| /* Firmware doesn't like 0 */ |
| ps_timeout = ieee80211_tu_to_usec( |
| vif->bss_conf.beacon_int) / 1000; |
| } |
| |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, param, |
| ps_timeout); |
| if (ret) { |
| ath10k_warn(ar, "failed to set inactivity time for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } else { |
| psmode = WMI_STA_PS_MODE_DISABLED; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d psmode %s\n", |
| arvif->vdev_id, psmode ? "enable" : "disable"); |
| |
| ret = ath10k_wmi_set_psmode(ar, arvif->vdev_id, psmode); |
| if (ret) { |
| ath10k_warn(ar, "failed to set PS Mode %d for vdev %d: %d\n", |
| psmode, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_vif_disable_keepalive(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct wmi_sta_keepalive_arg arg = {}; |
| int ret; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_STA) |
| return 0; |
| |
| if (!test_bit(WMI_SERVICE_STA_KEEP_ALIVE, ar->wmi.svc_map)) |
| return 0; |
| |
| /* Some firmware revisions have a bug and ignore the `enabled` field. |
| * Instead use the interval to disable the keepalive. |
| */ |
| arg.vdev_id = arvif->vdev_id; |
| arg.enabled = 1; |
| arg.method = WMI_STA_KEEPALIVE_METHOD_NULL_FRAME; |
| arg.interval = WMI_STA_KEEPALIVE_INTERVAL_DISABLE; |
| |
| ret = ath10k_wmi_sta_keepalive(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit keepalive on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static void ath10k_mac_vif_ap_csa_count_down(struct ath10k_vif *arvif) |
| { |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_vif *vif = arvif->vif; |
| int ret; |
| |
| lockdep_assert_held(&arvif->ar->conf_mutex); |
| |
| if (WARN_ON(!test_bit(WMI_SERVICE_BEACON_OFFLOAD, ar->wmi.svc_map))) |
| return; |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_AP) |
| return; |
| |
| if (!vif->bss_conf.csa_active) |
| return; |
| |
| if (!arvif->is_up) |
| return; |
| |
| if (!ieee80211_beacon_cntdwn_is_complete(vif, 0)) { |
| ieee80211_beacon_update_cntdwn(vif, 0); |
| |
| ret = ath10k_mac_setup_bcn_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to update bcn tmpl during csa: %d\n", |
| ret); |
| |
| ret = ath10k_mac_setup_prb_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to update prb tmpl during csa: %d\n", |
| ret); |
| } else { |
| ieee80211_csa_finish(vif, 0); |
| } |
| } |
| |
| static void ath10k_mac_vif_ap_csa_work(struct work_struct *work) |
| { |
| struct ath10k_vif *arvif = container_of(work, struct ath10k_vif, |
| ap_csa_work); |
| struct ath10k *ar = arvif->ar; |
| |
| mutex_lock(&ar->conf_mutex); |
| ath10k_mac_vif_ap_csa_count_down(arvif); |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static void ath10k_mac_handle_beacon_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct sk_buff *skb = data; |
| struct ieee80211_mgmt *mgmt = (void *)skb->data; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| |
| if (vif->type != NL80211_IFTYPE_STATION) |
| return; |
| |
| if (!ether_addr_equal(mgmt->bssid, vif->bss_conf.bssid)) |
| return; |
| |
| cancel_delayed_work(&arvif->connection_loss_work); |
| } |
| |
| void ath10k_mac_handle_beacon(struct ath10k *ar, struct sk_buff *skb) |
| { |
| ieee80211_iterate_active_interfaces_atomic(ar->hw, |
| ATH10K_ITER_NORMAL_FLAGS, |
| ath10k_mac_handle_beacon_iter, |
| skb); |
| } |
| |
| static void ath10k_mac_handle_beacon_miss_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| u32 *vdev_id = data; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k *ar = arvif->ar; |
| struct ieee80211_hw *hw = ar->hw; |
| |
| if (arvif->vdev_id != *vdev_id) |
| return; |
| |
| if (!arvif->is_up) |
| return; |
| |
| ieee80211_beacon_loss(vif); |
| |
| /* Firmware doesn't report beacon loss events repeatedly. If AP probe |
| * (done by mac80211) succeeds but beacons do not resume then it |
| * doesn't make sense to continue operation. Queue connection loss work |
| * which can be cancelled when beacon is received. |
| */ |
| ieee80211_queue_delayed_work(hw, &arvif->connection_loss_work, |
| ATH10K_CONNECTION_LOSS_HZ); |
| } |
| |
| void ath10k_mac_handle_beacon_miss(struct ath10k *ar, u32 vdev_id) |
| { |
| ieee80211_iterate_active_interfaces_atomic(ar->hw, |
| ATH10K_ITER_NORMAL_FLAGS, |
| ath10k_mac_handle_beacon_miss_iter, |
| &vdev_id); |
| } |
| |
| static void ath10k_mac_vif_sta_connection_loss_work(struct work_struct *work) |
| { |
| struct ath10k_vif *arvif = container_of(work, struct ath10k_vif, |
| connection_loss_work.work); |
| struct ieee80211_vif *vif = arvif->vif; |
| |
| if (!arvif->is_up) |
| return; |
| |
| ieee80211_connection_loss(vif); |
| } |
| |
| /**********************/ |
| /* Station management */ |
| /**********************/ |
| |
| static u32 ath10k_peer_assoc_h_listen_intval(struct ath10k *ar, |
| struct ieee80211_vif *vif) |
| { |
| /* Some firmware revisions have unstable STA powersave when listen |
| * interval is set too high (e.g. 5). The symptoms are firmware doesn't |
| * generate NullFunc frames properly even if buffered frames have been |
| * indicated in Beacon TIM. Firmware would seldom wake up to pull |
| * buffered frames. Often pinging the device from AP would simply fail. |
| * |
| * As a workaround set it to 1. |
| */ |
| if (vif->type == NL80211_IFTYPE_STATION) |
| return 1; |
| |
| return ar->hw->conf.listen_interval; |
| } |
| |
| static void ath10k_peer_assoc_h_basic(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| u32 aid; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (vif->type == NL80211_IFTYPE_STATION) |
| aid = vif->cfg.aid; |
| else |
| aid = sta->aid; |
| |
| ether_addr_copy(arg->addr, sta->addr); |
| arg->vdev_id = arvif->vdev_id; |
| arg->peer_aid = aid; |
| arg->peer_flags |= arvif->ar->wmi.peer_flags->auth; |
| arg->peer_listen_intval = ath10k_peer_assoc_h_listen_intval(ar, vif); |
| arg->peer_num_spatial_streams = 1; |
| arg->peer_caps = vif->bss_conf.assoc_capability; |
| } |
| |
| static void ath10k_peer_assoc_h_crypto(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| struct ieee80211_bss_conf *info = &vif->bss_conf; |
| struct cfg80211_chan_def def; |
| struct cfg80211_bss *bss; |
| const u8 *rsnie = NULL; |
| const u8 *wpaie = NULL; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return; |
| |
| bss = cfg80211_get_bss(ar->hw->wiphy, def.chan, info->bssid, |
| vif->cfg.ssid_len ? vif->cfg.ssid : NULL, |
| vif->cfg.ssid_len, |
| IEEE80211_BSS_TYPE_ANY, IEEE80211_PRIVACY_ANY); |
| if (bss) { |
| const struct cfg80211_bss_ies *ies; |
| |
| rcu_read_lock(); |
| rsnie = ieee80211_bss_get_ie(bss, WLAN_EID_RSN); |
| |
| ies = rcu_dereference(bss->ies); |
| |
| wpaie = cfg80211_find_vendor_ie(WLAN_OUI_MICROSOFT, |
| WLAN_OUI_TYPE_MICROSOFT_WPA, |
| ies->data, |
| ies->len); |
| rcu_read_unlock(); |
| cfg80211_put_bss(ar->hw->wiphy, bss); |
| } |
| |
| /* FIXME: base on RSN IE/WPA IE is a correct idea? */ |
| if (rsnie || wpaie) { |
| ath10k_dbg(ar, ATH10K_DBG_WMI, "%s: rsn ie found\n", __func__); |
| arg->peer_flags |= ar->wmi.peer_flags->need_ptk_4_way; |
| } |
| |
| if (wpaie) { |
| ath10k_dbg(ar, ATH10K_DBG_WMI, "%s: wpa ie found\n", __func__); |
| arg->peer_flags |= ar->wmi.peer_flags->need_gtk_2_way; |
| } |
| |
| if (sta->mfp && |
| test_bit(ATH10K_FW_FEATURE_MFP_SUPPORT, |
| ar->running_fw->fw_file.fw_features)) { |
| arg->peer_flags |= ar->wmi.peer_flags->pmf; |
| } |
| } |
| |
| static void ath10k_peer_assoc_h_rates(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct wmi_rate_set_arg *rateset = &arg->peer_legacy_rates; |
| struct cfg80211_chan_def def; |
| const struct ieee80211_supported_band *sband; |
| const struct ieee80211_rate *rates; |
| enum nl80211_band band; |
| u32 ratemask; |
| u8 rate; |
| int i; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return; |
| |
| band = def.chan->band; |
| sband = ar->hw->wiphy->bands[band]; |
| ratemask = sta->deflink.supp_rates[band]; |
| ratemask &= arvif->bitrate_mask.control[band].legacy; |
| rates = sband->bitrates; |
| |
| rateset->num_rates = 0; |
| |
| for (i = 0; i < 32; i++, ratemask >>= 1, rates++) { |
| if (!(ratemask & 1)) |
| continue; |
| |
| rate = ath10k_mac_bitrate_to_rate(rates->bitrate); |
| rateset->rates[rateset->num_rates] = rate; |
| rateset->num_rates++; |
| } |
| } |
| |
| static bool |
| ath10k_peer_assoc_h_ht_masked(const u8 ht_mcs_mask[IEEE80211_HT_MCS_MASK_LEN]) |
| { |
| int nss; |
| |
| for (nss = 0; nss < IEEE80211_HT_MCS_MASK_LEN; nss++) |
| if (ht_mcs_mask[nss]) |
| return false; |
| |
| return true; |
| } |
| |
| static bool |
| ath10k_peer_assoc_h_vht_masked(const u16 vht_mcs_mask[NL80211_VHT_NSS_MAX]) |
| { |
| int nss; |
| |
| for (nss = 0; nss < NL80211_VHT_NSS_MAX; nss++) |
| if (vht_mcs_mask[nss]) |
| return false; |
| |
| return true; |
| } |
| |
| static void ath10k_peer_assoc_h_ht(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| const struct ieee80211_sta_ht_cap *ht_cap = &sta->deflink.ht_cap; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct cfg80211_chan_def def; |
| enum nl80211_band band; |
| const u8 *ht_mcs_mask; |
| const u16 *vht_mcs_mask; |
| int i, n; |
| u8 max_nss; |
| u32 stbc; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return; |
| |
| if (!ht_cap->ht_supported) |
| return; |
| |
| band = def.chan->band; |
| ht_mcs_mask = arvif->bitrate_mask.control[band].ht_mcs; |
| vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs; |
| |
| if (ath10k_peer_assoc_h_ht_masked(ht_mcs_mask) && |
| ath10k_peer_assoc_h_vht_masked(vht_mcs_mask)) |
| return; |
| |
| arg->peer_flags |= ar->wmi.peer_flags->ht; |
| arg->peer_max_mpdu = (1 << (IEEE80211_HT_MAX_AMPDU_FACTOR + |
| ht_cap->ampdu_factor)) - 1; |
| |
| arg->peer_mpdu_density = |
| ath10k_parse_mpdudensity(ht_cap->ampdu_density); |
| |
| arg->peer_ht_caps = ht_cap->cap; |
| arg->peer_rate_caps |= WMI_RC_HT_FLAG; |
| |
| if (ht_cap->cap & IEEE80211_HT_CAP_LDPC_CODING) |
| arg->peer_flags |= ar->wmi.peer_flags->ldbc; |
| |
| if (sta->deflink.bandwidth >= IEEE80211_STA_RX_BW_40) { |
| arg->peer_flags |= ar->wmi.peer_flags->bw40; |
| arg->peer_rate_caps |= WMI_RC_CW40_FLAG; |
| } |
| |
| if (arvif->bitrate_mask.control[band].gi != NL80211_TXRATE_FORCE_LGI) { |
| if (ht_cap->cap & IEEE80211_HT_CAP_SGI_20) |
| arg->peer_rate_caps |= WMI_RC_SGI_FLAG; |
| |
| if (ht_cap->cap & IEEE80211_HT_CAP_SGI_40) |
| arg->peer_rate_caps |= WMI_RC_SGI_FLAG; |
| } |
| |
| if (ht_cap->cap & IEEE80211_HT_CAP_TX_STBC) { |
| arg->peer_rate_caps |= WMI_RC_TX_STBC_FLAG; |
| arg->peer_flags |= ar->wmi.peer_flags->stbc; |
| } |
| |
| if (ht_cap->cap & IEEE80211_HT_CAP_RX_STBC) { |
| stbc = ht_cap->cap & IEEE80211_HT_CAP_RX_STBC; |
| stbc = stbc >> IEEE80211_HT_CAP_RX_STBC_SHIFT; |
| stbc = stbc << WMI_RC_RX_STBC_FLAG_S; |
| arg->peer_rate_caps |= stbc; |
| arg->peer_flags |= ar->wmi.peer_flags->stbc; |
| } |
| |
| if (ht_cap->mcs.rx_mask[1] && ht_cap->mcs.rx_mask[2]) |
| arg->peer_rate_caps |= WMI_RC_TS_FLAG; |
| else if (ht_cap->mcs.rx_mask[1]) |
| arg->peer_rate_caps |= WMI_RC_DS_FLAG; |
| |
| for (i = 0, n = 0, max_nss = 0; i < IEEE80211_HT_MCS_MASK_LEN * 8; i++) |
| if ((ht_cap->mcs.rx_mask[i / 8] & BIT(i % 8)) && |
| (ht_mcs_mask[i / 8] & BIT(i % 8))) { |
| max_nss = (i / 8) + 1; |
| arg->peer_ht_rates.rates[n++] = i; |
| } |
| |
| /* |
| * This is a workaround for HT-enabled STAs which break the spec |
| * and have no HT capabilities RX mask (no HT RX MCS map). |
| * |
| * As per spec, in section 20.3.5 Modulation and coding scheme (MCS), |
| * MCS 0 through 7 are mandatory in 20MHz with 800 ns GI at all STAs. |
| * |
| * Firmware asserts if such situation occurs. |
| */ |
| if (n == 0) { |
| arg->peer_ht_rates.num_rates = 8; |
| for (i = 0; i < arg->peer_ht_rates.num_rates; i++) |
| arg->peer_ht_rates.rates[i] = i; |
| } else { |
| arg->peer_ht_rates.num_rates = n; |
| arg->peer_num_spatial_streams = min(sta->deflink.rx_nss, |
| max_nss); |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac ht peer %pM mcs cnt %d nss %d\n", |
| arg->addr, |
| arg->peer_ht_rates.num_rates, |
| arg->peer_num_spatial_streams); |
| } |
| |
| static int ath10k_peer_assoc_qos_ap(struct ath10k *ar, |
| struct ath10k_vif *arvif, |
| struct ieee80211_sta *sta) |
| { |
| u32 uapsd = 0; |
| u32 max_sp = 0; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (sta->wme && sta->uapsd_queues) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac uapsd_queues 0x%x max_sp %d\n", |
| sta->uapsd_queues, sta->max_sp); |
| |
| if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_VO) |
| uapsd |= WMI_AP_PS_UAPSD_AC3_DELIVERY_EN | |
| WMI_AP_PS_UAPSD_AC3_TRIGGER_EN; |
| if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_VI) |
| uapsd |= WMI_AP_PS_UAPSD_AC2_DELIVERY_EN | |
| WMI_AP_PS_UAPSD_AC2_TRIGGER_EN; |
| if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_BK) |
| uapsd |= WMI_AP_PS_UAPSD_AC1_DELIVERY_EN | |
| WMI_AP_PS_UAPSD_AC1_TRIGGER_EN; |
| if (sta->uapsd_queues & IEEE80211_WMM_IE_STA_QOSINFO_AC_BE) |
| uapsd |= WMI_AP_PS_UAPSD_AC0_DELIVERY_EN | |
| WMI_AP_PS_UAPSD_AC0_TRIGGER_EN; |
| |
| if (sta->max_sp < MAX_WMI_AP_PS_PEER_PARAM_MAX_SP) |
| max_sp = sta->max_sp; |
| |
| ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id, |
| sta->addr, |
| WMI_AP_PS_PEER_PARAM_UAPSD, |
| uapsd); |
| if (ret) { |
| ath10k_warn(ar, "failed to set ap ps peer param uapsd for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id, |
| sta->addr, |
| WMI_AP_PS_PEER_PARAM_MAX_SP, |
| max_sp); |
| if (ret) { |
| ath10k_warn(ar, "failed to set ap ps peer param max sp for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| /* TODO setup this based on STA listen interval and |
| * beacon interval. Currently we don't know |
| * sta->listen_interval - mac80211 patch required. |
| * Currently use 10 seconds |
| */ |
| ret = ath10k_wmi_set_ap_ps_param(ar, arvif->vdev_id, sta->addr, |
| WMI_AP_PS_PEER_PARAM_AGEOUT_TIME, |
| 10); |
| if (ret) { |
| ath10k_warn(ar, "failed to set ap ps peer param ageout time for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static u16 |
| ath10k_peer_assoc_h_vht_limit(u16 tx_mcs_set, |
| const u16 vht_mcs_limit[NL80211_VHT_NSS_MAX]) |
| { |
| int idx_limit; |
| int nss; |
| u16 mcs_map; |
| u16 mcs; |
| |
| for (nss = 0; nss < NL80211_VHT_NSS_MAX; nss++) { |
| mcs_map = ath10k_mac_get_max_vht_mcs_map(tx_mcs_set, nss) & |
| vht_mcs_limit[nss]; |
| |
| if (mcs_map) |
| idx_limit = fls(mcs_map) - 1; |
| else |
| idx_limit = -1; |
| |
| switch (idx_limit) { |
| case 0: |
| case 1: |
| case 2: |
| case 3: |
| case 4: |
| case 5: |
| case 6: |
| default: |
| /* see ath10k_mac_can_set_bitrate_mask() */ |
| WARN_ON(1); |
| fallthrough; |
| case -1: |
| mcs = IEEE80211_VHT_MCS_NOT_SUPPORTED; |
| break; |
| case 7: |
| mcs = IEEE80211_VHT_MCS_SUPPORT_0_7; |
| break; |
| case 8: |
| mcs = IEEE80211_VHT_MCS_SUPPORT_0_8; |
| break; |
| case 9: |
| mcs = IEEE80211_VHT_MCS_SUPPORT_0_9; |
| break; |
| } |
| |
| tx_mcs_set &= ~(0x3 << (nss * 2)); |
| tx_mcs_set |= mcs << (nss * 2); |
| } |
| |
| return tx_mcs_set; |
| } |
| |
| static u32 get_160mhz_nss_from_maxrate(int rate) |
| { |
| u32 nss; |
| |
| switch (rate) { |
| case 780: |
| nss = 1; |
| break; |
| case 1560: |
| nss = 2; |
| break; |
| case 2106: |
| nss = 3; /* not support MCS9 from spec*/ |
| break; |
| case 3120: |
| nss = 4; |
| break; |
| default: |
| nss = 1; |
| } |
| |
| return nss; |
| } |
| |
| static void ath10k_peer_assoc_h_vht(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| const struct ieee80211_sta_vht_cap *vht_cap = &sta->deflink.vht_cap; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_hw_params *hw = &ar->hw_params; |
| struct cfg80211_chan_def def; |
| enum nl80211_band band; |
| const u16 *vht_mcs_mask; |
| u8 ampdu_factor; |
| u8 max_nss, vht_mcs; |
| int i; |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return; |
| |
| if (!vht_cap->vht_supported) |
| return; |
| |
| band = def.chan->band; |
| vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs; |
| |
| if (ath10k_peer_assoc_h_vht_masked(vht_mcs_mask)) |
| return; |
| |
| arg->peer_flags |= ar->wmi.peer_flags->vht; |
| |
| if (def.chan->band == NL80211_BAND_2GHZ) |
| arg->peer_flags |= ar->wmi.peer_flags->vht_2g; |
| |
| arg->peer_vht_caps = vht_cap->cap; |
| |
| ampdu_factor = (vht_cap->cap & |
| IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK) >> |
| IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT; |
| |
| /* Workaround: Some Netgear/Linksys 11ac APs set Rx A-MPDU factor to |
| * zero in VHT IE. Using it would result in degraded throughput. |
| * arg->peer_max_mpdu at this point contains HT max_mpdu so keep |
| * it if VHT max_mpdu is smaller. |
| */ |
| arg->peer_max_mpdu = max(arg->peer_max_mpdu, |
| (1U << (IEEE80211_HT_MAX_AMPDU_FACTOR + |
| ampdu_factor)) - 1); |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_80) |
| arg->peer_flags |= ar->wmi.peer_flags->bw80; |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_160) |
| arg->peer_flags |= ar->wmi.peer_flags->bw160; |
| |
| /* Calculate peer NSS capability from VHT capabilities if STA |
| * supports VHT. |
| */ |
| for (i = 0, max_nss = 0, vht_mcs = 0; i < NL80211_VHT_NSS_MAX; i++) { |
| vht_mcs = __le16_to_cpu(vht_cap->vht_mcs.rx_mcs_map) >> |
| (2 * i) & 3; |
| |
| if ((vht_mcs != IEEE80211_VHT_MCS_NOT_SUPPORTED) && |
| vht_mcs_mask[i]) |
| max_nss = i + 1; |
| } |
| arg->peer_num_spatial_streams = min(sta->deflink.rx_nss, max_nss); |
| arg->peer_vht_rates.rx_max_rate = |
| __le16_to_cpu(vht_cap->vht_mcs.rx_highest); |
| arg->peer_vht_rates.rx_mcs_set = |
| __le16_to_cpu(vht_cap->vht_mcs.rx_mcs_map); |
| arg->peer_vht_rates.tx_max_rate = |
| __le16_to_cpu(vht_cap->vht_mcs.tx_highest); |
| arg->peer_vht_rates.tx_mcs_set = ath10k_peer_assoc_h_vht_limit( |
| __le16_to_cpu(vht_cap->vht_mcs.tx_mcs_map), vht_mcs_mask); |
| |
| /* Configure bandwidth-NSS mapping to FW |
| * for the chip's tx chains setting on 160Mhz bw |
| */ |
| if (arg->peer_phymode == MODE_11AC_VHT160 || |
| arg->peer_phymode == MODE_11AC_VHT80_80) { |
| u32 rx_nss; |
| u32 max_rate; |
| |
| max_rate = arg->peer_vht_rates.rx_max_rate; |
| rx_nss = get_160mhz_nss_from_maxrate(max_rate); |
| |
| if (rx_nss == 0) |
| rx_nss = arg->peer_num_spatial_streams; |
| else |
| rx_nss = min(arg->peer_num_spatial_streams, rx_nss); |
| |
| max_rate = hw->vht160_mcs_tx_highest; |
| rx_nss = min(rx_nss, get_160mhz_nss_from_maxrate(max_rate)); |
| |
| arg->peer_bw_rxnss_override = |
| FIELD_PREP(WMI_PEER_NSS_MAP_ENABLE, 1) | |
| FIELD_PREP(WMI_PEER_NSS_160MHZ_MASK, (rx_nss - 1)); |
| |
| if (arg->peer_phymode == MODE_11AC_VHT80_80) { |
| arg->peer_bw_rxnss_override |= |
| FIELD_PREP(WMI_PEER_NSS_80_80MHZ_MASK, (rx_nss - 1)); |
| } |
| } |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vht peer %pM max_mpdu %d flags 0x%x peer_rx_nss_override 0x%x\n", |
| sta->addr, arg->peer_max_mpdu, |
| arg->peer_flags, arg->peer_bw_rxnss_override); |
| } |
| |
| static void ath10k_peer_assoc_h_qos(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| |
| switch (arvif->vdev_type) { |
| case WMI_VDEV_TYPE_AP: |
| if (sta->wme) |
| arg->peer_flags |= arvif->ar->wmi.peer_flags->qos; |
| |
| if (sta->wme && sta->uapsd_queues) { |
| arg->peer_flags |= arvif->ar->wmi.peer_flags->apsd; |
| arg->peer_rate_caps |= WMI_RC_UAPSD_FLAG; |
| } |
| break; |
| case WMI_VDEV_TYPE_STA: |
| if (sta->wme) |
| arg->peer_flags |= arvif->ar->wmi.peer_flags->qos; |
| break; |
| case WMI_VDEV_TYPE_IBSS: |
| if (sta->wme) |
| arg->peer_flags |= arvif->ar->wmi.peer_flags->qos; |
| break; |
| default: |
| break; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac peer %pM qos %d\n", |
| sta->addr, !!(arg->peer_flags & |
| arvif->ar->wmi.peer_flags->qos)); |
| } |
| |
| static bool ath10k_mac_sta_has_ofdm_only(struct ieee80211_sta *sta) |
| { |
| return sta->deflink.supp_rates[NL80211_BAND_2GHZ] >> |
| ATH10K_MAC_FIRST_OFDM_RATE_IDX; |
| } |
| |
| static enum wmi_phy_mode ath10k_mac_get_phymode_vht(struct ath10k *ar, |
| struct ieee80211_sta *sta) |
| { |
| struct ieee80211_sta_vht_cap *vht_cap = &sta->deflink.vht_cap; |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_160) { |
| switch (vht_cap->cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK) { |
| case IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ: |
| return MODE_11AC_VHT160; |
| case IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ: |
| return MODE_11AC_VHT80_80; |
| default: |
| /* not sure if this is a valid case? */ |
| return MODE_11AC_VHT160; |
| } |
| } |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_80) |
| return MODE_11AC_VHT80; |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_40) |
| return MODE_11AC_VHT40; |
| |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_20) |
| return MODE_11AC_VHT20; |
| |
| return MODE_UNKNOWN; |
| } |
| |
| static void ath10k_peer_assoc_h_phymode(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct cfg80211_chan_def def; |
| enum nl80211_band band; |
| const u8 *ht_mcs_mask; |
| const u16 *vht_mcs_mask; |
| enum wmi_phy_mode phymode = MODE_UNKNOWN; |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return; |
| |
| band = def.chan->band; |
| ht_mcs_mask = arvif->bitrate_mask.control[band].ht_mcs; |
| vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs; |
| |
| switch (band) { |
| case NL80211_BAND_2GHZ: |
| if (sta->deflink.vht_cap.vht_supported && |
| !ath10k_peer_assoc_h_vht_masked(vht_mcs_mask)) { |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_40) |
| phymode = MODE_11AC_VHT40; |
| else |
| phymode = MODE_11AC_VHT20; |
| } else if (sta->deflink.ht_cap.ht_supported && |
| !ath10k_peer_assoc_h_ht_masked(ht_mcs_mask)) { |
| if (sta->deflink.bandwidth == IEEE80211_STA_RX_BW_40) |
| phymode = MODE_11NG_HT40; |
| else |
| phymode = MODE_11NG_HT20; |
| } else if (ath10k_mac_sta_has_ofdm_only(sta)) { |
| phymode = MODE_11G; |
| } else { |
| phymode = MODE_11B; |
| } |
| |
| break; |
| case NL80211_BAND_5GHZ: |
| /* |
| * Check VHT first. |
| */ |
| if (sta->deflink.vht_cap.vht_supported && |
| !ath10k_peer_assoc_h_vht_masked(vht_mcs_mask)) { |
| phymode = ath10k_mac_get_phymode_vht(ar, sta); |
| } else if (sta->deflink.ht_cap.ht_supported && |
| !ath10k_peer_assoc_h_ht_masked(ht_mcs_mask)) { |
| if (sta->deflink.bandwidth >= IEEE80211_STA_RX_BW_40) |
| phymode = MODE_11NA_HT40; |
| else |
| phymode = MODE_11NA_HT20; |
| } else { |
| phymode = MODE_11A; |
| } |
| |
| break; |
| default: |
| break; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac peer %pM phymode %s\n", |
| sta->addr, ath10k_wmi_phymode_str(phymode)); |
| |
| arg->peer_phymode = phymode; |
| WARN_ON(phymode == MODE_UNKNOWN); |
| } |
| |
| static int ath10k_peer_assoc_prepare(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct wmi_peer_assoc_complete_arg *arg) |
| { |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| memset(arg, 0, sizeof(*arg)); |
| |
| ath10k_peer_assoc_h_basic(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_crypto(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_rates(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_ht(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_phymode(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_vht(ar, vif, sta, arg); |
| ath10k_peer_assoc_h_qos(ar, vif, sta, arg); |
| |
| return 0; |
| } |
| |
| static const u32 ath10k_smps_map[] = { |
| [WLAN_HT_CAP_SM_PS_STATIC] = WMI_PEER_SMPS_STATIC, |
| [WLAN_HT_CAP_SM_PS_DYNAMIC] = WMI_PEER_SMPS_DYNAMIC, |
| [WLAN_HT_CAP_SM_PS_INVALID] = WMI_PEER_SMPS_PS_NONE, |
| [WLAN_HT_CAP_SM_PS_DISABLED] = WMI_PEER_SMPS_PS_NONE, |
| }; |
| |
| static int ath10k_setup_peer_smps(struct ath10k *ar, struct ath10k_vif *arvif, |
| const u8 *addr, |
| const struct ieee80211_sta_ht_cap *ht_cap) |
| { |
| int smps; |
| |
| if (!ht_cap->ht_supported) |
| return 0; |
| |
| smps = ht_cap->cap & IEEE80211_HT_CAP_SM_PS; |
| smps >>= IEEE80211_HT_CAP_SM_PS_SHIFT; |
| |
| if (smps >= ARRAY_SIZE(ath10k_smps_map)) |
| return -EINVAL; |
| |
| return ath10k_wmi_peer_set_param(ar, arvif->vdev_id, addr, |
| ar->wmi.peer_param->smps_state, |
| ath10k_smps_map[smps]); |
| } |
| |
| static int ath10k_mac_vif_recalc_txbf(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta_vht_cap vht_cap) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret; |
| u32 param; |
| u32 value; |
| |
| if (ath10k_wmi_get_txbf_conf_scheme(ar) != WMI_TXBF_CONF_AFTER_ASSOC) |
| return 0; |
| |
| if (!(ar->vht_cap_info & |
| (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE | |
| IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE))) |
| return 0; |
| |
| param = ar->wmi.vdev_param->txbf; |
| value = 0; |
| |
| if (WARN_ON(param == WMI_VDEV_PARAM_UNSUPPORTED)) |
| return 0; |
| |
| /* The following logic is correct. If a remote STA advertises support |
| * for being a beamformer then we should enable us being a beamformee. |
| */ |
| |
| if (ar->vht_cap_info & |
| (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE)) { |
| if (vht_cap.cap & IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFEE; |
| |
| if (vht_cap.cap & IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_MU_TX_BFEE; |
| } |
| |
| if (ar->vht_cap_info & |
| (IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE)) { |
| if (vht_cap.cap & IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFER; |
| |
| if (vht_cap.cap & IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_MU_TX_BFER; |
| } |
| |
| if (value & WMI_VDEV_PARAM_TXBF_MU_TX_BFEE) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFEE; |
| |
| if (value & WMI_VDEV_PARAM_TXBF_MU_TX_BFER) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFER; |
| |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, param, value); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit vdev param txbf 0x%x: %d\n", |
| value, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static bool ath10k_mac_is_connected(struct ath10k *ar) |
| { |
| struct ath10k_vif *arvif; |
| |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| if (arvif->is_up && arvif->vdev_type == WMI_VDEV_TYPE_STA) |
| return true; |
| } |
| |
| return false; |
| } |
| |
| static int ath10k_mac_txpower_setup(struct ath10k *ar, int txpower) |
| { |
| int ret; |
| u32 param; |
| int tx_power_2g, tx_power_5g; |
| bool connected; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| /* ath10k internally uses unit of 0.5 dBm so multiply by 2 */ |
| tx_power_2g = txpower * 2; |
| tx_power_5g = txpower * 2; |
| |
| connected = ath10k_mac_is_connected(ar); |
| |
| if (connected && ar->tx_power_2g_limit) |
| if (tx_power_2g > ar->tx_power_2g_limit) |
| tx_power_2g = ar->tx_power_2g_limit; |
| |
| if (connected && ar->tx_power_5g_limit) |
| if (tx_power_5g > ar->tx_power_5g_limit) |
| tx_power_5g = ar->tx_power_5g_limit; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac txpower 2g: %d, 5g: %d\n", |
| tx_power_2g, tx_power_5g); |
| |
| param = ar->wmi.pdev_param->txpower_limit2g; |
| ret = ath10k_wmi_pdev_set_param(ar, param, tx_power_2g); |
| if (ret) { |
| ath10k_warn(ar, "failed to set 2g txpower %d: %d\n", |
| tx_power_2g, ret); |
| return ret; |
| } |
| |
| param = ar->wmi.pdev_param->txpower_limit5g; |
| ret = ath10k_wmi_pdev_set_param(ar, param, tx_power_5g); |
| if (ret) { |
| ath10k_warn(ar, "failed to set 5g txpower %d: %d\n", |
| tx_power_5g, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_txpower_recalc(struct ath10k *ar) |
| { |
| struct ath10k_vif *arvif; |
| int ret, txpower = -1; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| /* txpower not initialized yet? */ |
| if (arvif->txpower == INT_MIN) |
| continue; |
| |
| if (txpower == -1) |
| txpower = arvif->txpower; |
| else |
| txpower = min(txpower, arvif->txpower); |
| } |
| |
| if (txpower == -1) |
| return 0; |
| |
| ret = ath10k_mac_txpower_setup(ar, txpower); |
| if (ret) { |
| ath10k_warn(ar, "failed to setup tx power %d: %d\n", |
| txpower, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_set_sar_power(struct ath10k *ar) |
| { |
| if (!ar->hw_params.dynamic_sar_support) |
| return -EOPNOTSUPP; |
| |
| if (!ath10k_mac_is_connected(ar)) |
| return 0; |
| |
| /* if connected, then arvif->txpower must be valid */ |
| return ath10k_mac_txpower_recalc(ar); |
| } |
| |
| static int ath10k_mac_set_sar_specs(struct ieee80211_hw *hw, |
| const struct cfg80211_sar_specs *sar) |
| { |
| const struct cfg80211_sar_sub_specs *sub_specs; |
| struct ath10k *ar = hw->priv; |
| u32 i; |
| int ret; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (!ar->hw_params.dynamic_sar_support) { |
| ret = -EOPNOTSUPP; |
| goto err; |
| } |
| |
| if (!sar || sar->type != NL80211_SAR_TYPE_POWER || |
| sar->num_sub_specs == 0) { |
| ret = -EINVAL; |
| goto err; |
| } |
| |
| sub_specs = sar->sub_specs; |
| |
| /* 0dbm is not a practical value for ath10k, so use 0 |
| * as no SAR limitation on it. |
| */ |
| ar->tx_power_2g_limit = 0; |
| ar->tx_power_5g_limit = 0; |
| |
| /* note the power is in 0.25dbm unit, while ath10k uses |
| * 0.5dbm unit. |
| */ |
| for (i = 0; i < sar->num_sub_specs; i++) { |
| if (sub_specs->freq_range_index == 0) |
| ar->tx_power_2g_limit = sub_specs->power / 2; |
| else if (sub_specs->freq_range_index == 1) |
| ar->tx_power_5g_limit = sub_specs->power / 2; |
| |
| sub_specs++; |
| } |
| |
| ret = ath10k_mac_set_sar_power(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to set sar power: %d", ret); |
| goto err; |
| } |
| |
| err: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| /* can be called only in mac80211 callbacks due to `key_count` usage */ |
| static void ath10k_bss_assoc(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *bss_conf) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ieee80211_sta_ht_cap ht_cap; |
| struct ieee80211_sta_vht_cap vht_cap; |
| struct wmi_peer_assoc_complete_arg peer_arg; |
| struct ieee80211_sta *ap_sta; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i assoc bssid %pM aid %d\n", |
| arvif->vdev_id, arvif->bssid, arvif->aid); |
| |
| rcu_read_lock(); |
| |
| ap_sta = ieee80211_find_sta(vif, bss_conf->bssid); |
| if (!ap_sta) { |
| ath10k_warn(ar, "failed to find station entry for bss %pM vdev %i\n", |
| bss_conf->bssid, arvif->vdev_id); |
| rcu_read_unlock(); |
| return; |
| } |
| |
| /* ap_sta must be accessed only within rcu section which must be left |
| * before calling ath10k_setup_peer_smps() which might sleep. |
| */ |
| ht_cap = ap_sta->deflink.ht_cap; |
| vht_cap = ap_sta->deflink.vht_cap; |
| |
| ret = ath10k_peer_assoc_prepare(ar, vif, ap_sta, &peer_arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to prepare peer assoc for %pM vdev %i: %d\n", |
| bss_conf->bssid, arvif->vdev_id, ret); |
| rcu_read_unlock(); |
| return; |
| } |
| |
| rcu_read_unlock(); |
| |
| ret = ath10k_wmi_peer_assoc(ar, &peer_arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to run peer assoc for %pM vdev %i: %d\n", |
| bss_conf->bssid, arvif->vdev_id, ret); |
| return; |
| } |
| |
| ret = ath10k_setup_peer_smps(ar, arvif, bss_conf->bssid, &ht_cap); |
| if (ret) { |
| ath10k_warn(ar, "failed to setup peer SMPS for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return; |
| } |
| |
| ret = ath10k_mac_vif_recalc_txbf(ar, vif, vht_cap); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc txbf for vdev %i on bss %pM: %d\n", |
| arvif->vdev_id, bss_conf->bssid, ret); |
| return; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d up (associated) bssid %pM aid %d\n", |
| arvif->vdev_id, bss_conf->bssid, vif->cfg.aid); |
| |
| WARN_ON(arvif->is_up); |
| |
| arvif->aid = vif->cfg.aid; |
| ether_addr_copy(arvif->bssid, bss_conf->bssid); |
| |
| ret = ath10k_wmi_pdev_set_param(ar, |
| ar->wmi.pdev_param->peer_stats_info_enable, 1); |
| if (ret) |
| ath10k_warn(ar, "failed to enable peer stats info: %d\n", ret); |
| |
| ret = ath10k_wmi_vdev_up(ar, arvif->vdev_id, arvif->aid, arvif->bssid); |
| if (ret) { |
| ath10k_warn(ar, "failed to set vdev %d up: %d\n", |
| arvif->vdev_id, ret); |
| return; |
| } |
| |
| arvif->is_up = true; |
| |
| ath10k_mac_set_sar_power(ar); |
| |
| /* Workaround: Some firmware revisions (tested with qca6174 |
| * WLAN.RM.2.0-00073) have buggy powersave state machine and must be |
| * poked with peer param command. |
| */ |
| ret = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, arvif->bssid, |
| ar->wmi.peer_param->dummy_var, 1); |
| if (ret) { |
| ath10k_warn(ar, "failed to poke peer %pM param for ps workaround on vdev %i: %d\n", |
| arvif->bssid, arvif->vdev_id, ret); |
| return; |
| } |
| } |
| |
| static void ath10k_bss_disassoc(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ieee80211_sta_vht_cap vht_cap = {}; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i disassoc bssid %pM\n", |
| arvif->vdev_id, arvif->bssid); |
| |
| ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to down vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| arvif->def_wep_key_idx = -1; |
| |
| ret = ath10k_mac_vif_recalc_txbf(ar, vif, vht_cap); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc txbf for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return; |
| } |
| |
| arvif->is_up = false; |
| |
| ath10k_mac_txpower_recalc(ar); |
| |
| cancel_delayed_work_sync(&arvif->connection_loss_work); |
| } |
| |
| static int ath10k_new_peer_tid_config(struct ath10k *ar, |
| struct ieee80211_sta *sta, |
| struct ath10k_vif *arvif) |
| { |
| struct wmi_per_peer_per_tid_cfg_arg arg = {}; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| bool config_apply; |
| int ret, i; |
| |
| for (i = 0; i < ATH10K_TID_MAX; i++) { |
| config_apply = false; |
| if (arvif->retry_long[i] || arvif->ampdu[i] || |
| arvif->rate_ctrl[i] || arvif->rtscts[i]) { |
| config_apply = true; |
| arg.tid = i; |
| arg.vdev_id = arvif->vdev_id; |
| arg.retry_count = arvif->retry_long[i]; |
| arg.aggr_control = arvif->ampdu[i]; |
| arg.rate_ctrl = arvif->rate_ctrl[i]; |
| arg.rcode_flags = arvif->rate_code[i]; |
| |
| if (arvif->rtscts[i]) |
| arg.ext_tid_cfg_bitmap = |
| WMI_EXT_TID_RTS_CTS_CONFIG; |
| else |
| arg.ext_tid_cfg_bitmap = 0; |
| |
| arg.rtscts_ctrl = arvif->rtscts[i]; |
| } |
| |
| if (arvif->noack[i]) { |
| arg.ack_policy = arvif->noack[i]; |
| arg.rate_ctrl = WMI_TID_CONFIG_RATE_CONTROL_DEFAULT_LOWEST_RATE; |
| arg.aggr_control = WMI_TID_CONFIG_AGGR_CONTROL_DISABLE; |
| config_apply = true; |
| } |
| |
| /* Assign default value(-1) to newly connected station. |
| * This is to identify station specific tid configuration not |
| * configured for the station. |
| */ |
| arsta->retry_long[i] = -1; |
| arsta->noack[i] = -1; |
| arsta->ampdu[i] = -1; |
| |
| if (!config_apply) |
| continue; |
| |
| ether_addr_copy(arg.peer_macaddr.addr, sta->addr); |
| |
| ret = ath10k_wmi_set_per_peer_per_tid_cfg(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to set per tid retry/aggr config for sta %pM: %d\n", |
| sta->addr, ret); |
| return ret; |
| } |
| |
| memset(&arg, 0, sizeof(arg)); |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_station_assoc(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| bool reassoc) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct wmi_peer_assoc_complete_arg peer_arg; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_peer_assoc_prepare(ar, vif, sta, &peer_arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to prepare WMI peer assoc for %pM vdev %i: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_wmi_peer_assoc(ar, &peer_arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to run peer assoc for STA %pM vdev %i: %d\n", |
| sta->addr, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| /* Re-assoc is run only to update supported rates for given station. It |
| * doesn't make much sense to reconfigure the peer completely. |
| */ |
| if (!reassoc) { |
| ret = ath10k_setup_peer_smps(ar, arvif, sta->addr, |
| &sta->deflink.ht_cap); |
| if (ret) { |
| ath10k_warn(ar, "failed to setup peer SMPS for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_peer_assoc_qos_ap(ar, arvif, sta); |
| if (ret) { |
| ath10k_warn(ar, "failed to set qos params for STA %pM for vdev %i: %d\n", |
| sta->addr, arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| if (!sta->wme) { |
| arvif->num_legacy_stations++; |
| ret = ath10k_recalc_rtscts_prot(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } |
| |
| /* Plumb cached keys only for static WEP */ |
| if ((arvif->def_wep_key_idx != -1) && (!sta->tdls)) { |
| ret = ath10k_install_peer_wep_keys(arvif, sta->addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to install peer wep keys for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } |
| } |
| |
| if (!test_bit(WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT, ar->wmi.svc_map)) |
| return ret; |
| |
| return ath10k_new_peer_tid_config(ar, sta, arvif); |
| } |
| |
| static int ath10k_station_disassoc(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (!sta->wme) { |
| arvif->num_legacy_stations--; |
| ret = ath10k_recalc_rtscts_prot(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } |
| |
| ret = ath10k_clear_peer_keys(arvif, sta->addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to clear all peer wep keys for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| return ret; |
| } |
| |
| /**************/ |
| /* Regulatory */ |
| /**************/ |
| |
| static int ath10k_update_channel_list(struct ath10k *ar) |
| { |
| struct ieee80211_hw *hw = ar->hw; |
| struct ieee80211_supported_band **bands; |
| enum nl80211_band band; |
| struct ieee80211_channel *channel; |
| struct wmi_scan_chan_list_arg arg = {0}; |
| struct wmi_channel_arg *ch; |
| bool passive; |
| int len; |
| int ret; |
| int i; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| bands = hw->wiphy->bands; |
| for (band = 0; band < NUM_NL80211_BANDS; band++) { |
| if (!bands[band]) |
| continue; |
| |
| for (i = 0; i < bands[band]->n_channels; i++) { |
| if (bands[band]->channels[i].flags & |
| IEEE80211_CHAN_DISABLED) |
| continue; |
| |
| arg.n_channels++; |
| } |
| } |
| |
| len = sizeof(struct wmi_channel_arg) * arg.n_channels; |
| arg.channels = kzalloc(len, GFP_KERNEL); |
| if (!arg.channels) |
| return -ENOMEM; |
| |
| ch = arg.channels; |
| for (band = 0; band < NUM_NL80211_BANDS; band++) { |
| if (!bands[band]) |
| continue; |
| |
| for (i = 0; i < bands[band]->n_channels; i++) { |
| channel = &bands[band]->channels[i]; |
| |
| if (channel->flags & IEEE80211_CHAN_DISABLED) |
| continue; |
| |
| ch->allow_ht = true; |
| |
| /* FIXME: when should we really allow VHT? */ |
| ch->allow_vht = true; |
| |
| ch->allow_ibss = |
| !(channel->flags & IEEE80211_CHAN_NO_IR); |
| |
| ch->ht40plus = |
| !(channel->flags & IEEE80211_CHAN_NO_HT40PLUS); |
| |
| ch->chan_radar = |
| !!(channel->flags & IEEE80211_CHAN_RADAR); |
| |
| passive = channel->flags & IEEE80211_CHAN_NO_IR; |
| ch->passive = passive; |
| |
| /* the firmware is ignoring the "radar" flag of the |
| * channel and is scanning actively using Probe Requests |
| * on "Radar detection"/DFS channels which are not |
| * marked as "available" |
| */ |
| ch->passive |= ch->chan_radar; |
| |
| ch->freq = channel->center_freq; |
| ch->band_center_freq1 = channel->center_freq; |
| ch->min_power = 0; |
| ch->max_power = channel->max_power * 2; |
| ch->max_reg_power = channel->max_reg_power * 2; |
| ch->max_antenna_gain = channel->max_antenna_gain; |
| ch->reg_class_id = 0; /* FIXME */ |
| |
| /* FIXME: why use only legacy modes, why not any |
| * HT/VHT modes? Would that even make any |
| * difference? |
| */ |
| if (channel->band == NL80211_BAND_2GHZ) |
| ch->mode = MODE_11G; |
| else |
| ch->mode = MODE_11A; |
| |
| if (WARN_ON_ONCE(ch->mode == MODE_UNKNOWN)) |
| continue; |
| |
| ath10k_dbg(ar, ATH10K_DBG_WMI, |
| "mac channel [%zd/%d] freq %d maxpower %d regpower %d antenna %d mode %d\n", |
| ch - arg.channels, arg.n_channels, |
| ch->freq, ch->max_power, ch->max_reg_power, |
| ch->max_antenna_gain, ch->mode); |
| |
| ch++; |
| } |
| } |
| |
| ret = ath10k_wmi_scan_chan_list(ar, &arg); |
| kfree(arg.channels); |
| |
| return ret; |
| } |
| |
| static enum wmi_dfs_region |
| ath10k_mac_get_dfs_region(enum nl80211_dfs_regions dfs_region) |
| { |
| switch (dfs_region) { |
| case NL80211_DFS_UNSET: |
| return WMI_UNINIT_DFS_DOMAIN; |
| case NL80211_DFS_FCC: |
| return WMI_FCC_DFS_DOMAIN; |
| case NL80211_DFS_ETSI: |
| return WMI_ETSI_DFS_DOMAIN; |
| case NL80211_DFS_JP: |
| return WMI_MKK4_DFS_DOMAIN; |
| } |
| return WMI_UNINIT_DFS_DOMAIN; |
| } |
| |
| static void ath10k_regd_update(struct ath10k *ar) |
| { |
| struct reg_dmn_pair_mapping *regpair; |
| int ret; |
| enum wmi_dfs_region wmi_dfs_reg; |
| enum nl80211_dfs_regions nl_dfs_reg; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_update_channel_list(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to update channel list: %d\n", ret); |
| |
| regpair = ar->ath_common.regulatory.regpair; |
| |
| if (IS_ENABLED(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) { |
| nl_dfs_reg = ar->dfs_detector->region; |
| wmi_dfs_reg = ath10k_mac_get_dfs_region(nl_dfs_reg); |
| } else { |
| wmi_dfs_reg = WMI_UNINIT_DFS_DOMAIN; |
| } |
| |
| /* Target allows setting up per-band regdomain but ath_common provides |
| * a combined one only |
| */ |
| ret = ath10k_wmi_pdev_set_regdomain(ar, |
| regpair->reg_domain, |
| regpair->reg_domain, /* 2ghz */ |
| regpair->reg_domain, /* 5ghz */ |
| regpair->reg_2ghz_ctl, |
| regpair->reg_5ghz_ctl, |
| wmi_dfs_reg); |
| if (ret) |
| ath10k_warn(ar, "failed to set pdev regdomain: %d\n", ret); |
| } |
| |
| static void ath10k_mac_update_channel_list(struct ath10k *ar, |
| struct ieee80211_supported_band *band) |
| { |
| int i; |
| |
| if (ar->low_5ghz_chan && ar->high_5ghz_chan) { |
| for (i = 0; i < band->n_channels; i++) { |
| if (band->channels[i].center_freq < ar->low_5ghz_chan || |
| band->channels[i].center_freq > ar->high_5ghz_chan) |
| band->channels[i].flags |= |
| IEEE80211_CHAN_DISABLED; |
| } |
| } |
| } |
| |
| static void ath10k_reg_notifier(struct wiphy *wiphy, |
| struct regulatory_request *request) |
| { |
| struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy); |
| struct ath10k *ar = hw->priv; |
| bool result; |
| |
| ath_reg_notifier_apply(wiphy, request, &ar->ath_common.regulatory); |
| |
| if (IS_ENABLED(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) { |
| ath10k_dbg(ar, ATH10K_DBG_REGULATORY, "dfs region 0x%x\n", |
| request->dfs_region); |
| result = ar->dfs_detector->set_dfs_domain(ar->dfs_detector, |
| request->dfs_region); |
| if (!result) |
| ath10k_warn(ar, "DFS region 0x%X not supported, will trigger radar for every pulse\n", |
| request->dfs_region); |
| } |
| |
| mutex_lock(&ar->conf_mutex); |
| if (ar->state == ATH10K_STATE_ON) |
| ath10k_regd_update(ar); |
| mutex_unlock(&ar->conf_mutex); |
| |
| if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) |
| ath10k_mac_update_channel_list(ar, |
| ar->hw->wiphy->bands[NL80211_BAND_5GHZ]); |
| } |
| |
| static void ath10k_stop_radar_confirmation(struct ath10k *ar) |
| { |
| spin_lock_bh(&ar->data_lock); |
| ar->radar_conf_state = ATH10K_RADAR_CONFIRMATION_STOPPED; |
| spin_unlock_bh(&ar->data_lock); |
| |
| cancel_work_sync(&ar->radar_confirmation_work); |
| } |
| |
| /***************/ |
| /* TX handlers */ |
| /***************/ |
| |
| enum ath10k_mac_tx_path { |
| ATH10K_MAC_TX_HTT, |
| ATH10K_MAC_TX_HTT_MGMT, |
| ATH10K_MAC_TX_WMI_MGMT, |
| ATH10K_MAC_TX_UNKNOWN, |
| }; |
| |
| void ath10k_mac_tx_lock(struct ath10k *ar, int reason) |
| { |
| lockdep_assert_held(&ar->htt.tx_lock); |
| |
| WARN_ON(reason >= ATH10K_TX_PAUSE_MAX); |
| ar->tx_paused |= BIT(reason); |
| ieee80211_stop_queues(ar->hw); |
| } |
| |
| static void ath10k_mac_tx_unlock_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = data; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| |
| if (arvif->tx_paused) |
| return; |
| |
| ieee80211_wake_queue(ar->hw, arvif->vdev_id); |
| } |
| |
| void ath10k_mac_tx_unlock(struct ath10k *ar, int reason) |
| { |
| lockdep_assert_held(&ar->htt.tx_lock); |
| |
| WARN_ON(reason >= ATH10K_TX_PAUSE_MAX); |
| ar->tx_paused &= ~BIT(reason); |
| |
| if (ar->tx_paused) |
| return; |
| |
| ieee80211_iterate_active_interfaces_atomic(ar->hw, |
| ATH10K_ITER_RESUME_FLAGS, |
| ath10k_mac_tx_unlock_iter, |
| ar); |
| |
| ieee80211_wake_queue(ar->hw, ar->hw->offchannel_tx_hw_queue); |
| } |
| |
| void ath10k_mac_vif_tx_lock(struct ath10k_vif *arvif, int reason) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->htt.tx_lock); |
| |
| WARN_ON(reason >= BITS_PER_LONG); |
| arvif->tx_paused |= BIT(reason); |
| ieee80211_stop_queue(ar->hw, arvif->vdev_id); |
| } |
| |
| void ath10k_mac_vif_tx_unlock(struct ath10k_vif *arvif, int reason) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->htt.tx_lock); |
| |
| WARN_ON(reason >= BITS_PER_LONG); |
| arvif->tx_paused &= ~BIT(reason); |
| |
| if (ar->tx_paused) |
| return; |
| |
| if (arvif->tx_paused) |
| return; |
| |
| ieee80211_wake_queue(ar->hw, arvif->vdev_id); |
| } |
| |
| static void ath10k_mac_vif_handle_tx_pause(struct ath10k_vif *arvif, |
| enum wmi_tlv_tx_pause_id pause_id, |
| enum wmi_tlv_tx_pause_action action) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->htt.tx_lock); |
| |
| switch (action) { |
| case WMI_TLV_TX_PAUSE_ACTION_STOP: |
| ath10k_mac_vif_tx_lock(arvif, pause_id); |
| break; |
| case WMI_TLV_TX_PAUSE_ACTION_WAKE: |
| ath10k_mac_vif_tx_unlock(arvif, pause_id); |
| break; |
| default: |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, |
| "received unknown tx pause action %d on vdev %i, ignoring\n", |
| action, arvif->vdev_id); |
| break; |
| } |
| } |
| |
| struct ath10k_mac_tx_pause { |
| u32 vdev_id; |
| enum wmi_tlv_tx_pause_id pause_id; |
| enum wmi_tlv_tx_pause_action action; |
| }; |
| |
| static void ath10k_mac_handle_tx_pause_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_mac_tx_pause *arg = data; |
| |
| if (arvif->vdev_id != arg->vdev_id) |
| return; |
| |
| ath10k_mac_vif_handle_tx_pause(arvif, arg->pause_id, arg->action); |
| } |
| |
| void ath10k_mac_handle_tx_pause_vdev(struct ath10k *ar, u32 vdev_id, |
| enum wmi_tlv_tx_pause_id pause_id, |
| enum wmi_tlv_tx_pause_action action) |
| { |
| struct ath10k_mac_tx_pause arg = { |
| .vdev_id = vdev_id, |
| .pause_id = pause_id, |
| .action = action, |
| }; |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| ieee80211_iterate_active_interfaces_atomic(ar->hw, |
| ATH10K_ITER_RESUME_FLAGS, |
| ath10k_mac_handle_tx_pause_iter, |
| &arg); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| } |
| |
| static enum ath10k_hw_txrx_mode |
| ath10k_mac_tx_h_get_txmode(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct sk_buff *skb) |
| { |
| const struct ieee80211_hdr *hdr = (void *)skb->data; |
| const struct ath10k_skb_cb *skb_cb = ATH10K_SKB_CB(skb); |
| __le16 fc = hdr->frame_control; |
| |
| if (IEEE80211_SKB_CB(skb)->flags & IEEE80211_TX_CTL_HW_80211_ENCAP) |
| return ATH10K_HW_TXRX_ETHERNET; |
| |
| if (!vif || vif->type == NL80211_IFTYPE_MONITOR) |
| return ATH10K_HW_TXRX_RAW; |
| |
| if (ieee80211_is_mgmt(fc)) |
| return ATH10K_HW_TXRX_MGMT; |
| |
| /* Workaround: |
| * |
| * NullFunc frames are mostly used to ping if a client or AP are still |
| * reachable and responsive. This implies tx status reports must be |
| * accurate - otherwise either mac80211 or userspace (e.g. hostapd) can |
| * come to a conclusion that the other end disappeared and tear down |
| * BSS connection or it can never disconnect from BSS/client (which is |
| * the case). |
| * |
| * Firmware with HTT older than 3.0 delivers incorrect tx status for |
| * NullFunc frames to driver. However there's a HTT Mgmt Tx command |
| * which seems to deliver correct tx reports for NullFunc frames. The |
| * downside of using it is it ignores client powersave state so it can |
| * end up disconnecting sleeping clients in AP mode. It should fix STA |
| * mode though because AP don't sleep. |
| */ |
| if (ar->htt.target_version_major < 3 && |
| (ieee80211_is_nullfunc(fc) || ieee80211_is_qos_nullfunc(fc)) && |
| !test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX, |
| ar->running_fw->fw_file.fw_features)) |
| return ATH10K_HW_TXRX_MGMT; |
| |
| /* Workaround: |
| * |
| * Some wmi-tlv firmwares for qca6174 have broken Tx key selection for |
| * NativeWifi txmode - it selects AP key instead of peer key. It seems |
| * to work with Ethernet txmode so use it. |
| * |
| * FIXME: Check if raw mode works with TDLS. |
| */ |
| if (ieee80211_is_data_present(fc) && sta && sta->tdls) |
| return ATH10K_HW_TXRX_ETHERNET; |
| |
| if (test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags) || |
| skb_cb->flags & ATH10K_SKB_F_RAW_TX) |
| return ATH10K_HW_TXRX_RAW; |
| |
| return ATH10K_HW_TXRX_NATIVE_WIFI; |
| } |
| |
| static bool ath10k_tx_h_use_hwcrypto(struct ieee80211_vif *vif, |
| struct sk_buff *skb) |
| { |
| const struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| const struct ieee80211_hdr *hdr = (void *)skb->data; |
| const u32 mask = IEEE80211_TX_INTFL_DONT_ENCRYPT | |
| IEEE80211_TX_CTL_INJECTED; |
| |
| if (!ieee80211_has_protected(hdr->frame_control)) |
| return false; |
| |
| if ((info->flags & mask) == mask) |
| return false; |
| |
| if (vif) |
| return !((struct ath10k_vif *)vif->drv_priv)->nohwcrypt; |
| |
| return true; |
| } |
| |
| /* HTT Tx uses Native Wifi tx mode which expects 802.11 frames without QoS |
| * Control in the header. |
| */ |
| static void ath10k_tx_h_nwifi(struct ieee80211_hw *hw, struct sk_buff *skb) |
| { |
| struct ieee80211_hdr *hdr = (void *)skb->data; |
| struct ath10k_skb_cb *cb = ATH10K_SKB_CB(skb); |
| u8 *qos_ctl; |
| |
| if (!ieee80211_is_data_qos(hdr->frame_control)) |
| return; |
| |
| qos_ctl = ieee80211_get_qos_ctl(hdr); |
| memmove(skb->data + IEEE80211_QOS_CTL_LEN, |
| skb->data, (void *)qos_ctl - (void *)skb->data); |
| skb_pull(skb, IEEE80211_QOS_CTL_LEN); |
| |
| /* Some firmware revisions don't handle sending QoS NullFunc well. |
| * These frames are mainly used for CQM purposes so it doesn't really |
| * matter whether QoS NullFunc or NullFunc are sent. |
| */ |
| hdr = (void *)skb->data; |
| if (ieee80211_is_qos_nullfunc(hdr->frame_control)) |
| cb->flags &= ~ATH10K_SKB_F_QOS; |
| |
| hdr->frame_control &= ~__cpu_to_le16(IEEE80211_STYPE_QOS_DATA); |
| } |
| |
| static void ath10k_tx_h_8023(struct sk_buff *skb) |
| { |
| struct ieee80211_hdr *hdr; |
| struct rfc1042_hdr *rfc1042; |
| struct ethhdr *eth; |
| size_t hdrlen; |
| u8 da[ETH_ALEN]; |
| u8 sa[ETH_ALEN]; |
| __be16 type; |
| |
| hdr = (void *)skb->data; |
| hdrlen = ieee80211_hdrlen(hdr->frame_control); |
| rfc1042 = (void *)skb->data + hdrlen; |
| |
| ether_addr_copy(da, ieee80211_get_DA(hdr)); |
| ether_addr_copy(sa, ieee80211_get_SA(hdr)); |
| type = rfc1042->snap_type; |
| |
| skb_pull(skb, hdrlen + sizeof(*rfc1042)); |
| skb_push(skb, sizeof(*eth)); |
| |
| eth = (void *)skb->data; |
| ether_addr_copy(eth->h_dest, da); |
| ether_addr_copy(eth->h_source, sa); |
| eth->h_proto = type; |
| } |
| |
| static void ath10k_tx_h_add_p2p_noa_ie(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct sk_buff *skb) |
| { |
| struct ieee80211_hdr *hdr = (struct ieee80211_hdr *)skb->data; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| |
| /* This is case only for P2P_GO */ |
| if (vif->type != NL80211_IFTYPE_AP || !vif->p2p) |
| return; |
| |
| if (unlikely(ieee80211_is_probe_resp(hdr->frame_control))) { |
| spin_lock_bh(&ar->data_lock); |
| if (arvif->u.ap.noa_data) |
| if (!pskb_expand_head(skb, 0, arvif->u.ap.noa_len, |
| GFP_ATOMIC)) |
| skb_put_data(skb, arvif->u.ap.noa_data, |
| arvif->u.ap.noa_len); |
| spin_unlock_bh(&ar->data_lock); |
| } |
| } |
| |
| static void ath10k_mac_tx_h_fill_cb(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_txq *txq, |
| struct ieee80211_sta *sta, |
| struct sk_buff *skb, u16 airtime) |
| { |
| struct ieee80211_hdr *hdr = (void *)skb->data; |
| struct ath10k_skb_cb *cb = ATH10K_SKB_CB(skb); |
| const struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| bool is_data = ieee80211_is_data(hdr->frame_control) || |
| ieee80211_is_data_qos(hdr->frame_control); |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_sta *arsta; |
| u8 tid, *qos_ctl; |
| bool noack = false; |
| |
| cb->flags = 0; |
| |
| if (info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP) { |
| cb->flags |= ATH10K_SKB_F_QOS; /* Assume data frames are QoS */ |
| goto finish_cb_fill; |
| } |
| |
| if (!ath10k_tx_h_use_hwcrypto(vif, skb)) |
| cb->flags |= ATH10K_SKB_F_NO_HWCRYPT; |
| |
| if (ieee80211_is_mgmt(hdr->frame_control)) |
| cb->flags |= ATH10K_SKB_F_MGMT; |
| |
| if (ieee80211_is_data_qos(hdr->frame_control)) { |
| cb->flags |= ATH10K_SKB_F_QOS; |
| qos_ctl = ieee80211_get_qos_ctl(hdr); |
| tid = (*qos_ctl) & IEEE80211_QOS_CTL_TID_MASK; |
| |
| if (arvif->noack[tid] == WMI_PEER_TID_CONFIG_NOACK) |
| noack = true; |
| |
| if (sta) { |
| arsta = (struct ath10k_sta *)sta->drv_priv; |
| |
| if (arsta->noack[tid] == WMI_PEER_TID_CONFIG_NOACK) |
| noack = true; |
| |
| if (arsta->noack[tid] == WMI_PEER_TID_CONFIG_ACK) |
| noack = false; |
| } |
| |
| if (noack) |
| cb->flags |= ATH10K_SKB_F_NOACK_TID; |
| } |
| |
| /* Data frames encrypted in software will be posted to firmware |
| * with tx encap mode set to RAW. Ex: Multicast traffic generated |
| * for a specific VLAN group will always be encrypted in software. |
| */ |
| if (is_data && ieee80211_has_protected(hdr->frame_control) && |
| !info->control.hw_key) { |
| cb->flags |= ATH10K_SKB_F_NO_HWCRYPT; |
| cb->flags |= ATH10K_SKB_F_RAW_TX; |
| } |
| |
| finish_cb_fill: |
| cb->vif = vif; |
| cb->txq = txq; |
| cb->airtime_est = airtime; |
| if (sta) { |
| arsta = (struct ath10k_sta *)sta->drv_priv; |
| spin_lock_bh(&ar->data_lock); |
| cb->ucast_cipher = arsta->ucast_cipher; |
| spin_unlock_bh(&ar->data_lock); |
| } |
| } |
| |
| bool ath10k_mac_tx_frm_has_freq(struct ath10k *ar) |
| { |
| /* FIXME: Not really sure since when the behaviour changed. At some |
| * point new firmware stopped requiring creation of peer entries for |
| * offchannel tx (and actually creating them causes issues with wmi-htc |
| * tx credit replenishment and reliability). Assuming it's at least 3.4 |
| * because that's when the `freq` was introduced to TX_FRM HTT command. |
| */ |
| return (ar->htt.target_version_major >= 3 && |
| ar->htt.target_version_minor >= 4 && |
| ar->running_fw->fw_file.htt_op_version == ATH10K_FW_HTT_OP_VERSION_TLV); |
| } |
| |
| static int ath10k_mac_tx_wmi_mgmt(struct ath10k *ar, struct sk_buff *skb) |
| { |
| struct sk_buff_head *q = &ar->wmi_mgmt_tx_queue; |
| |
| if (skb_queue_len_lockless(q) >= ATH10K_MAX_NUM_MGMT_PENDING) { |
| ath10k_warn(ar, "wmi mgmt tx queue is full\n"); |
| return -ENOSPC; |
| } |
| |
| skb_queue_tail(q, skb); |
| ieee80211_queue_work(ar->hw, &ar->wmi_mgmt_tx_work); |
| |
| return 0; |
| } |
| |
| static enum ath10k_mac_tx_path |
| ath10k_mac_tx_h_get_txpath(struct ath10k *ar, |
| struct sk_buff *skb, |
| enum ath10k_hw_txrx_mode txmode) |
| { |
| switch (txmode) { |
| case ATH10K_HW_TXRX_RAW: |
| case ATH10K_HW_TXRX_NATIVE_WIFI: |
| case ATH10K_HW_TXRX_ETHERNET: |
| return ATH10K_MAC_TX_HTT; |
| case ATH10K_HW_TXRX_MGMT: |
| if (test_bit(ATH10K_FW_FEATURE_HAS_WMI_MGMT_TX, |
| ar->running_fw->fw_file.fw_features) || |
| test_bit(WMI_SERVICE_MGMT_TX_WMI, |
| ar->wmi.svc_map)) |
| return ATH10K_MAC_TX_WMI_MGMT; |
| else if (ar->htt.target_version_major >= 3) |
| return ATH10K_MAC_TX_HTT; |
| else |
| return ATH10K_MAC_TX_HTT_MGMT; |
| } |
| |
| return ATH10K_MAC_TX_UNKNOWN; |
| } |
| |
| static int ath10k_mac_tx_submit(struct ath10k *ar, |
| enum ath10k_hw_txrx_mode txmode, |
| enum ath10k_mac_tx_path txpath, |
| struct sk_buff *skb) |
| { |
| struct ath10k_htt *htt = &ar->htt; |
| int ret = -EINVAL; |
| |
| switch (txpath) { |
| case ATH10K_MAC_TX_HTT: |
| ret = ath10k_htt_tx(htt, txmode, skb); |
| break; |
| case ATH10K_MAC_TX_HTT_MGMT: |
| ret = ath10k_htt_mgmt_tx(htt, skb); |
| break; |
| case ATH10K_MAC_TX_WMI_MGMT: |
| ret = ath10k_mac_tx_wmi_mgmt(ar, skb); |
| break; |
| case ATH10K_MAC_TX_UNKNOWN: |
| WARN_ON_ONCE(1); |
| ret = -EINVAL; |
| break; |
| } |
| |
| if (ret) { |
| ath10k_warn(ar, "failed to transmit packet, dropping: %d\n", |
| ret); |
| ieee80211_free_txskb(ar->hw, skb); |
| } |
| |
| return ret; |
| } |
| |
| /* This function consumes the sk_buff regardless of return value as far as |
| * caller is concerned so no freeing is necessary afterwards. |
| */ |
| static int ath10k_mac_tx(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| enum ath10k_hw_txrx_mode txmode, |
| enum ath10k_mac_tx_path txpath, |
| struct sk_buff *skb, bool noque_offchan) |
| { |
| struct ieee80211_hw *hw = ar->hw; |
| struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| const struct ath10k_skb_cb *skb_cb = ATH10K_SKB_CB(skb); |
| int ret; |
| |
| /* We should disable CCK RATE due to P2P */ |
| if (info->flags & IEEE80211_TX_CTL_NO_CCK_RATE) |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "IEEE80211_TX_CTL_NO_CCK_RATE\n"); |
| |
| switch (txmode) { |
| case ATH10K_HW_TXRX_MGMT: |
| case ATH10K_HW_TXRX_NATIVE_WIFI: |
| ath10k_tx_h_nwifi(hw, skb); |
| ath10k_tx_h_add_p2p_noa_ie(ar, vif, skb); |
| ath10k_tx_h_seq_no(vif, skb); |
| break; |
| case ATH10K_HW_TXRX_ETHERNET: |
| /* Convert 802.11->802.3 header only if the frame was earlier |
| * encapsulated to 802.11 by mac80211. Otherwise pass it as is. |
| */ |
| if (!(info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP)) |
| ath10k_tx_h_8023(skb); |
| break; |
| case ATH10K_HW_TXRX_RAW: |
| if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags) && |
| !(skb_cb->flags & ATH10K_SKB_F_RAW_TX)) { |
| WARN_ON_ONCE(1); |
| ieee80211_free_txskb(hw, skb); |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| if (!noque_offchan && info->flags & IEEE80211_TX_CTL_TX_OFFCHAN) { |
| if (!ath10k_mac_tx_frm_has_freq(ar)) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac queued offchannel skb %pK len %d\n", |
| skb, skb->len); |
| |
| skb_queue_tail(&ar->offchan_tx_queue, skb); |
| ieee80211_queue_work(hw, &ar->offchan_tx_work); |
| return 0; |
| } |
| } |
| |
| ret = ath10k_mac_tx_submit(ar, txmode, txpath, skb); |
| if (ret) { |
| ath10k_warn(ar, "failed to submit frame: %d\n", ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| void ath10k_offchan_tx_purge(struct ath10k *ar) |
| { |
| struct sk_buff *skb; |
| |
| for (;;) { |
| skb = skb_dequeue(&ar->offchan_tx_queue); |
| if (!skb) |
| break; |
| |
| ieee80211_free_txskb(ar->hw, skb); |
| } |
| } |
| |
| void ath10k_offchan_tx_work(struct work_struct *work) |
| { |
| struct ath10k *ar = container_of(work, struct ath10k, offchan_tx_work); |
| struct ath10k_peer *peer; |
| struct ath10k_vif *arvif; |
| enum ath10k_hw_txrx_mode txmode; |
| enum ath10k_mac_tx_path txpath; |
| struct ieee80211_hdr *hdr; |
| struct ieee80211_vif *vif; |
| struct ieee80211_sta *sta; |
| struct sk_buff *skb; |
| const u8 *peer_addr; |
| int vdev_id; |
| int ret; |
| unsigned long time_left; |
| bool tmp_peer_created = false; |
| |
| /* FW requirement: We must create a peer before FW will send out |
| * an offchannel frame. Otherwise the frame will be stuck and |
| * never transmitted. We delete the peer upon tx completion. |
| * It is unlikely that a peer for offchannel tx will already be |
| * present. However it may be in some rare cases so account for that. |
| * Otherwise we might remove a legitimate peer and break stuff. |
| */ |
| |
| for (;;) { |
| skb = skb_dequeue(&ar->offchan_tx_queue); |
| if (!skb) |
| break; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac offchannel skb %pK len %d\n", |
| skb, skb->len); |
| |
| hdr = (struct ieee80211_hdr *)skb->data; |
| peer_addr = ieee80211_get_DA(hdr); |
| |
| spin_lock_bh(&ar->data_lock); |
| vdev_id = ar->scan.vdev_id; |
| peer = ath10k_peer_find(ar, vdev_id, peer_addr); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (peer) { |
| ath10k_warn(ar, "peer %pM on vdev %d already present\n", |
| peer_addr, vdev_id); |
| } else { |
| ret = ath10k_peer_create(ar, NULL, NULL, vdev_id, |
| peer_addr, |
| WMI_PEER_TYPE_DEFAULT); |
| if (ret) |
| ath10k_warn(ar, "failed to create peer %pM on vdev %d: %d\n", |
| peer_addr, vdev_id, ret); |
| tmp_peer_created = (ret == 0); |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| reinit_completion(&ar->offchan_tx_completed); |
| ar->offchan_tx_skb = skb; |
| spin_unlock_bh(&ar->data_lock); |
| |
| /* It's safe to access vif and sta - conf_mutex guarantees that |
| * sta_state() and remove_interface() are locked exclusively |
| * out wrt to this offchannel worker. |
| */ |
| arvif = ath10k_get_arvif(ar, vdev_id); |
| if (arvif) { |
| vif = arvif->vif; |
| sta = ieee80211_find_sta(vif, peer_addr); |
| } else { |
| vif = NULL; |
| sta = NULL; |
| } |
| |
| txmode = ath10k_mac_tx_h_get_txmode(ar, vif, sta, skb); |
| txpath = ath10k_mac_tx_h_get_txpath(ar, skb, txmode); |
| |
| ret = ath10k_mac_tx(ar, vif, txmode, txpath, skb, true); |
| if (ret) { |
| ath10k_warn(ar, "failed to transmit offchannel frame: %d\n", |
| ret); |
| /* not serious */ |
| } |
| |
| time_left = |
| wait_for_completion_timeout(&ar->offchan_tx_completed, 3 * HZ); |
| if (time_left == 0) |
| ath10k_warn(ar, "timed out waiting for offchannel skb %pK, len: %d\n", |
| skb, skb->len); |
| |
| if (!peer && tmp_peer_created) { |
| ret = ath10k_peer_delete(ar, vdev_id, peer_addr); |
| if (ret) |
| ath10k_warn(ar, "failed to delete peer %pM on vdev %d: %d\n", |
| peer_addr, vdev_id, ret); |
| } |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| } |
| |
| void ath10k_mgmt_over_wmi_tx_purge(struct ath10k *ar) |
| { |
| struct sk_buff *skb; |
| |
| for (;;) { |
| skb = skb_dequeue(&ar->wmi_mgmt_tx_queue); |
| if (!skb) |
| break; |
| |
| ieee80211_free_txskb(ar->hw, skb); |
| } |
| } |
| |
| void ath10k_mgmt_over_wmi_tx_work(struct work_struct *work) |
| { |
| struct ath10k *ar = container_of(work, struct ath10k, wmi_mgmt_tx_work); |
| struct sk_buff *skb; |
| dma_addr_t paddr; |
| int ret; |
| |
| for (;;) { |
| skb = skb_dequeue(&ar->wmi_mgmt_tx_queue); |
| if (!skb) |
| break; |
| |
| if (test_bit(ATH10K_FW_FEATURE_MGMT_TX_BY_REF, |
| ar->running_fw->fw_file.fw_features)) { |
| paddr = dma_map_single(ar->dev, skb->data, |
| skb->len, DMA_TO_DEVICE); |
| if (dma_mapping_error(ar->dev, paddr)) { |
| ieee80211_free_txskb(ar->hw, skb); |
| continue; |
| } |
| ret = ath10k_wmi_mgmt_tx_send(ar, skb, paddr); |
| if (ret) { |
| ath10k_warn(ar, "failed to transmit management frame by ref via WMI: %d\n", |
| ret); |
| /* remove this msdu from idr tracking */ |
| ath10k_wmi_cleanup_mgmt_tx_send(ar, skb); |
| |
| dma_unmap_single(ar->dev, paddr, skb->len, |
| DMA_TO_DEVICE); |
| ieee80211_free_txskb(ar->hw, skb); |
| } |
| } else { |
| ret = ath10k_wmi_mgmt_tx(ar, skb); |
| if (ret) { |
| ath10k_warn(ar, "failed to transmit management frame via WMI: %d\n", |
| ret); |
| ieee80211_free_txskb(ar->hw, skb); |
| } |
| } |
| } |
| } |
| |
| static void ath10k_mac_txq_init(struct ieee80211_txq *txq) |
| { |
| struct ath10k_txq *artxq; |
| |
| if (!txq) |
| return; |
| |
| artxq = (void *)txq->drv_priv; |
| INIT_LIST_HEAD(&artxq->list); |
| } |
| |
| static void ath10k_mac_txq_unref(struct ath10k *ar, struct ieee80211_txq *txq) |
| { |
| struct ath10k_skb_cb *cb; |
| struct sk_buff *msdu; |
| int msdu_id; |
| |
| if (!txq) |
| return; |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| idr_for_each_entry(&ar->htt.pending_tx, msdu, msdu_id) { |
| cb = ATH10K_SKB_CB(msdu); |
| if (cb->txq == txq) |
| cb->txq = NULL; |
| } |
| spin_unlock_bh(&ar->htt.tx_lock); |
| } |
| |
| struct ieee80211_txq *ath10k_mac_txq_lookup(struct ath10k *ar, |
| u16 peer_id, |
| u8 tid) |
| { |
| struct ath10k_peer *peer; |
| |
| lockdep_assert_held(&ar->data_lock); |
| |
| peer = ar->peer_map[peer_id]; |
| if (!peer) |
| return NULL; |
| |
| if (peer->removed) |
| return NULL; |
| |
| if (peer->sta) |
| return peer->sta->txq[tid]; |
| else if (peer->vif) |
| return peer->vif->txq; |
| else |
| return NULL; |
| } |
| |
| static bool ath10k_mac_tx_can_push(struct ieee80211_hw *hw, |
| struct ieee80211_txq *txq) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_txq *artxq = (void *)txq->drv_priv; |
| |
| /* No need to get locks */ |
| if (ar->htt.tx_q_state.mode == HTT_TX_MODE_SWITCH_PUSH) |
| return true; |
| |
| if (ar->htt.num_pending_tx < ar->htt.tx_q_state.num_push_allowed) |
| return true; |
| |
| if (artxq->num_fw_queued < artxq->num_push_allowed) |
| return true; |
| |
| return false; |
| } |
| |
| /* Return estimated airtime in microsecond, which is calculated using last |
| * reported TX rate. This is just a rough estimation because host driver has no |
| * knowledge of the actual transmit rate, retries or aggregation. If actual |
| * airtime can be reported by firmware, then delta between estimated and actual |
| * airtime can be adjusted from deficit. |
| */ |
| #define IEEE80211_ATF_OVERHEAD 100 /* IFS + some slot time */ |
| #define IEEE80211_ATF_OVERHEAD_IFS 16 /* IFS only */ |
| static u16 ath10k_mac_update_airtime(struct ath10k *ar, |
| struct ieee80211_txq *txq, |
| struct sk_buff *skb) |
| { |
| struct ath10k_sta *arsta; |
| u32 pktlen; |
| u16 airtime = 0; |
| |
| if (!txq || !txq->sta) |
| return airtime; |
| |
| if (test_bit(WMI_SERVICE_REPORT_AIRTIME, ar->wmi.svc_map)) |
| return airtime; |
| |
| spin_lock_bh(&ar->data_lock); |
| arsta = (struct ath10k_sta *)txq->sta->drv_priv; |
| |
| pktlen = skb->len + 38; /* Assume MAC header 30, SNAP 8 for most case */ |
| if (arsta->last_tx_bitrate) { |
| /* airtime in us, last_tx_bitrate in 100kbps */ |
| airtime = (pktlen * 8 * (1000 / 100)) |
| / arsta->last_tx_bitrate; |
| /* overhead for media access time and IFS */ |
| airtime += IEEE80211_ATF_OVERHEAD_IFS; |
| } else { |
| /* This is mostly for throttle excessive BC/MC frames, and the |
| * airtime/rate doesn't need be exact. Airtime of BC/MC frames |
| * in 2G get some discount, which helps prevent very low rate |
| * frames from being blocked for too long. |
| */ |
| airtime = (pktlen * 8 * (1000 / 100)) / 60; /* 6M */ |
| airtime += IEEE80211_ATF_OVERHEAD; |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| return airtime; |
| } |
| |
| int ath10k_mac_tx_push_txq(struct ieee80211_hw *hw, |
| struct ieee80211_txq *txq) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_htt *htt = &ar->htt; |
| struct ath10k_txq *artxq = (void *)txq->drv_priv; |
| struct ieee80211_vif *vif = txq->vif; |
| struct ieee80211_sta *sta = txq->sta; |
| enum ath10k_hw_txrx_mode txmode; |
| enum ath10k_mac_tx_path txpath; |
| struct sk_buff *skb; |
| struct ieee80211_hdr *hdr; |
| size_t skb_len; |
| bool is_mgmt, is_presp; |
| int ret; |
| u16 airtime; |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| ret = ath10k_htt_tx_inc_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| if (ret) |
| return ret; |
| |
| skb = ieee80211_tx_dequeue_ni(hw, txq); |
| if (!skb) { |
| spin_lock_bh(&ar->htt.tx_lock); |
| ath10k_htt_tx_dec_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| return -ENOENT; |
| } |
| |
| airtime = ath10k_mac_update_airtime(ar, txq, skb); |
| ath10k_mac_tx_h_fill_cb(ar, vif, txq, sta, skb, airtime); |
| |
| skb_len = skb->len; |
| txmode = ath10k_mac_tx_h_get_txmode(ar, vif, sta, skb); |
| txpath = ath10k_mac_tx_h_get_txpath(ar, skb, txmode); |
| is_mgmt = (txpath == ATH10K_MAC_TX_HTT_MGMT); |
| |
| if (is_mgmt) { |
| hdr = (struct ieee80211_hdr *)skb->data; |
| is_presp = ieee80211_is_probe_resp(hdr->frame_control); |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| ret = ath10k_htt_tx_mgmt_inc_pending(htt, is_mgmt, is_presp); |
| |
| if (ret) { |
| ath10k_htt_tx_dec_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| return ret; |
| } |
| spin_unlock_bh(&ar->htt.tx_lock); |
| } |
| |
| ret = ath10k_mac_tx(ar, vif, txmode, txpath, skb, false); |
| if (unlikely(ret)) { |
| ath10k_warn(ar, "failed to push frame: %d\n", ret); |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| ath10k_htt_tx_dec_pending(htt); |
| if (is_mgmt) |
| ath10k_htt_tx_mgmt_dec_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| return ret; |
| } |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| artxq->num_fw_queued++; |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| return skb_len; |
| } |
| |
| static int ath10k_mac_schedule_txq(struct ieee80211_hw *hw, u32 ac) |
| { |
| struct ieee80211_txq *txq; |
| int ret = 0; |
| |
| ieee80211_txq_schedule_start(hw, ac); |
| while ((txq = ieee80211_next_txq(hw, ac))) { |
| while (ath10k_mac_tx_can_push(hw, txq)) { |
| ret = ath10k_mac_tx_push_txq(hw, txq); |
| if (ret < 0) |
| break; |
| } |
| ieee80211_return_txq(hw, txq, false); |
| ath10k_htt_tx_txq_update(hw, txq); |
| if (ret == -EBUSY) |
| break; |
| } |
| ieee80211_txq_schedule_end(hw, ac); |
| |
| return ret; |
| } |
| |
| void ath10k_mac_tx_push_pending(struct ath10k *ar) |
| { |
| struct ieee80211_hw *hw = ar->hw; |
| u32 ac; |
| |
| if (ar->htt.tx_q_state.mode != HTT_TX_MODE_SWITCH_PUSH) |
| return; |
| |
| if (ar->htt.num_pending_tx >= (ar->htt.max_num_pending_tx / 2)) |
| return; |
| |
| rcu_read_lock(); |
| for (ac = 0; ac < IEEE80211_NUM_ACS; ac++) { |
| if (ath10k_mac_schedule_txq(hw, ac) == -EBUSY) |
| break; |
| } |
| rcu_read_unlock(); |
| } |
| EXPORT_SYMBOL(ath10k_mac_tx_push_pending); |
| |
| /************/ |
| /* Scanning */ |
| /************/ |
| |
| void __ath10k_scan_finish(struct ath10k *ar) |
| { |
| lockdep_assert_held(&ar->data_lock); |
| |
| switch (ar->scan.state) { |
| case ATH10K_SCAN_IDLE: |
| break; |
| case ATH10K_SCAN_RUNNING: |
| case ATH10K_SCAN_ABORTING: |
| if (ar->scan.is_roc && ar->scan.roc_notify) |
| ieee80211_remain_on_channel_expired(ar->hw); |
| fallthrough; |
| case ATH10K_SCAN_STARTING: |
| if (!ar->scan.is_roc) { |
| struct cfg80211_scan_info info = { |
| .aborted = ((ar->scan.state == |
| ATH10K_SCAN_ABORTING) || |
| (ar->scan.state == |
| ATH10K_SCAN_STARTING)), |
| }; |
| |
| ieee80211_scan_completed(ar->hw, &info); |
| } |
| |
| ar->scan.state = ATH10K_SCAN_IDLE; |
| ar->scan_channel = NULL; |
| ar->scan.roc_freq = 0; |
| ath10k_offchan_tx_purge(ar); |
| cancel_delayed_work(&ar->scan.timeout); |
| complete(&ar->scan.completed); |
| break; |
| } |
| } |
| |
| void ath10k_scan_finish(struct ath10k *ar) |
| { |
| spin_lock_bh(&ar->data_lock); |
| __ath10k_scan_finish(ar); |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| static int ath10k_scan_stop(struct ath10k *ar) |
| { |
| struct wmi_stop_scan_arg arg = { |
| .req_id = 1, /* FIXME */ |
| .req_type = WMI_SCAN_STOP_ONE, |
| .u.scan_id = ATH10K_SCAN_ID, |
| }; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_stop_scan(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to stop wmi scan: %d\n", ret); |
| goto out; |
| } |
| |
| ret = wait_for_completion_timeout(&ar->scan.completed, 3 * HZ); |
| if (ret == 0) { |
| ath10k_warn(ar, "failed to receive scan abortion completion: timed out\n"); |
| ret = -ETIMEDOUT; |
| } else if (ret > 0) { |
| ret = 0; |
| } |
| |
| out: |
| /* Scan state should be updated upon scan completion but in case |
| * firmware fails to deliver the event (for whatever reason) it is |
| * desired to clean up scan state anyway. Firmware may have just |
| * dropped the scan completion event delivery due to transport pipe |
| * being overflown with data and/or it can recover on its own before |
| * next scan request is submitted. |
| */ |
| spin_lock_bh(&ar->data_lock); |
| if (ar->scan.state != ATH10K_SCAN_IDLE) |
| __ath10k_scan_finish(ar); |
| spin_unlock_bh(&ar->data_lock); |
| |
| return ret; |
| } |
| |
| static void ath10k_scan_abort(struct ath10k *ar) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| switch (ar->scan.state) { |
| case ATH10K_SCAN_IDLE: |
| /* This can happen if timeout worker kicked in and called |
| * abortion while scan completion was being processed. |
| */ |
| break; |
| case ATH10K_SCAN_STARTING: |
| case ATH10K_SCAN_ABORTING: |
| ath10k_warn(ar, "refusing scan abortion due to invalid scan state: %s (%d)\n", |
| ath10k_scan_state_str(ar->scan.state), |
| ar->scan.state); |
| break; |
| case ATH10K_SCAN_RUNNING: |
| ar->scan.state = ATH10K_SCAN_ABORTING; |
| spin_unlock_bh(&ar->data_lock); |
| |
| ret = ath10k_scan_stop(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to abort scan: %d\n", ret); |
| |
| spin_lock_bh(&ar->data_lock); |
| break; |
| } |
| |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| void ath10k_scan_timeout_work(struct work_struct *work) |
| { |
| struct ath10k *ar = container_of(work, struct ath10k, |
| scan.timeout.work); |
| |
| mutex_lock(&ar->conf_mutex); |
| ath10k_scan_abort(ar); |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static int ath10k_start_scan(struct ath10k *ar, |
| const struct wmi_start_scan_arg *arg) |
| { |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_start_scan(ar, arg); |
| if (ret) |
| return ret; |
| |
| ret = wait_for_completion_timeout(&ar->scan.started, 1 * HZ); |
| if (ret == 0) { |
| ret = ath10k_scan_stop(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to stop scan: %d\n", ret); |
| |
| return -ETIMEDOUT; |
| } |
| |
| /* If we failed to start the scan, return error code at |
| * this point. This is probably due to some issue in the |
| * firmware, but no need to wedge the driver due to that... |
| */ |
| spin_lock_bh(&ar->data_lock); |
| if (ar->scan.state == ATH10K_SCAN_IDLE) { |
| spin_unlock_bh(&ar->data_lock); |
| return -EINVAL; |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| return 0; |
| } |
| |
| /**********************/ |
| /* mac80211 callbacks */ |
| /**********************/ |
| |
| static void ath10k_mac_op_tx(struct ieee80211_hw *hw, |
| struct ieee80211_tx_control *control, |
| struct sk_buff *skb) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_htt *htt = &ar->htt; |
| struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| struct ieee80211_vif *vif = info->control.vif; |
| struct ieee80211_sta *sta = control->sta; |
| struct ieee80211_txq *txq = NULL; |
| enum ath10k_hw_txrx_mode txmode; |
| enum ath10k_mac_tx_path txpath; |
| bool is_htt; |
| bool is_mgmt; |
| int ret; |
| u16 airtime; |
| |
| airtime = ath10k_mac_update_airtime(ar, txq, skb); |
| ath10k_mac_tx_h_fill_cb(ar, vif, txq, sta, skb, airtime); |
| |
| txmode = ath10k_mac_tx_h_get_txmode(ar, vif, sta, skb); |
| txpath = ath10k_mac_tx_h_get_txpath(ar, skb, txmode); |
| is_htt = (txpath == ATH10K_MAC_TX_HTT || |
| txpath == ATH10K_MAC_TX_HTT_MGMT); |
| is_mgmt = (txpath == ATH10K_MAC_TX_HTT_MGMT); |
| |
| if (is_htt) { |
| bool is_presp = false; |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| if (!(info->flags & IEEE80211_TX_CTL_HW_80211_ENCAP)) { |
| struct ieee80211_hdr *hdr = (void *)skb->data; |
| |
| is_presp = ieee80211_is_probe_resp(hdr->frame_control); |
| } |
| |
| ret = ath10k_htt_tx_inc_pending(htt); |
| if (ret) { |
| ath10k_warn(ar, "failed to increase tx pending count: %d, dropping\n", |
| ret); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| ieee80211_free_txskb(ar->hw, skb); |
| return; |
| } |
| |
| ret = ath10k_htt_tx_mgmt_inc_pending(htt, is_mgmt, is_presp); |
| if (ret) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "failed to increase tx mgmt pending count: %d, dropping\n", |
| ret); |
| ath10k_htt_tx_dec_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| ieee80211_free_txskb(ar->hw, skb); |
| return; |
| } |
| spin_unlock_bh(&ar->htt.tx_lock); |
| } |
| |
| ret = ath10k_mac_tx(ar, vif, txmode, txpath, skb, false); |
| if (ret) { |
| ath10k_warn(ar, "failed to transmit frame: %d\n", ret); |
| if (is_htt) { |
| spin_lock_bh(&ar->htt.tx_lock); |
| ath10k_htt_tx_dec_pending(htt); |
| if (is_mgmt) |
| ath10k_htt_tx_mgmt_dec_pending(htt); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| } |
| return; |
| } |
| } |
| |
| static void ath10k_mac_op_wake_tx_queue(struct ieee80211_hw *hw, |
| struct ieee80211_txq *txq) |
| { |
| struct ath10k *ar = hw->priv; |
| int ret; |
| u8 ac = txq->ac; |
| |
| ath10k_htt_tx_txq_update(hw, txq); |
| if (ar->htt.tx_q_state.mode != HTT_TX_MODE_SWITCH_PUSH) |
| return; |
| |
| spin_lock_bh(&ar->queue_lock[ac]); |
| |
| ieee80211_txq_schedule_start(hw, ac); |
| txq = ieee80211_next_txq(hw, ac); |
| if (!txq) |
| goto out; |
| |
| while (ath10k_mac_tx_can_push(hw, txq)) { |
| ret = ath10k_mac_tx_push_txq(hw, txq); |
| if (ret < 0) |
| break; |
| } |
| ieee80211_return_txq(hw, txq, false); |
| ath10k_htt_tx_txq_update(hw, txq); |
| out: |
| ieee80211_txq_schedule_end(hw, ac); |
| spin_unlock_bh(&ar->queue_lock[ac]); |
| } |
| |
| /* Must not be called with conf_mutex held as workers can use that also. */ |
| void ath10k_drain_tx(struct ath10k *ar) |
| { |
| lockdep_assert_not_held(&ar->conf_mutex); |
| |
| /* make sure rcu-protected mac80211 tx path itself is drained */ |
| synchronize_net(); |
| |
| ath10k_offchan_tx_purge(ar); |
| ath10k_mgmt_over_wmi_tx_purge(ar); |
| |
| cancel_work_sync(&ar->offchan_tx_work); |
| cancel_work_sync(&ar->wmi_mgmt_tx_work); |
| } |
| |
| void ath10k_halt(struct ath10k *ar) |
| { |
| struct ath10k_vif *arvif; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| clear_bit(ATH10K_CAC_RUNNING, &ar->dev_flags); |
| ar->filter_flags = 0; |
| ar->monitor = false; |
| ar->monitor_arvif = NULL; |
| |
| if (ar->monitor_started) |
| ath10k_monitor_stop(ar); |
| |
| ar->monitor_started = false; |
| ar->tx_paused = 0; |
| |
| ath10k_scan_finish(ar); |
| ath10k_peer_cleanup_all(ar); |
| ath10k_stop_radar_confirmation(ar); |
| ath10k_core_stop(ar); |
| ath10k_hif_power_down(ar); |
| |
| spin_lock_bh(&ar->data_lock); |
| list_for_each_entry(arvif, &ar->arvifs, list) |
| ath10k_mac_vif_beacon_cleanup(arvif); |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| static int ath10k_get_antenna(struct ieee80211_hw *hw, u32 *tx_ant, u32 *rx_ant) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| *tx_ant = ar->cfg_tx_chainmask; |
| *rx_ant = ar->cfg_rx_chainmask; |
| |
| mutex_unlock(&ar->conf_mutex); |
| |
| return 0; |
| } |
| |
| static bool ath10k_check_chain_mask(struct ath10k *ar, u32 cm, const char *dbg) |
| { |
| /* It is not clear that allowing gaps in chainmask |
| * is helpful. Probably it will not do what user |
| * is hoping for, so warn in that case. |
| */ |
| if (cm == 15 || cm == 7 || cm == 3 || cm == 1 || cm == 0) |
| return true; |
| |
| ath10k_warn(ar, "mac %s antenna chainmask is invalid: 0x%x. Suggested values: 15, 7, 3, 1 or 0.\n", |
| dbg, cm); |
| return false; |
| } |
| |
| static int ath10k_mac_get_vht_cap_bf_sts(struct ath10k *ar) |
| { |
| int nsts = ar->vht_cap_info; |
| |
| nsts &= IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK; |
| nsts >>= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT; |
| |
| /* If firmware does not deliver to host number of space-time |
| * streams supported, assume it support up to 4 BF STS and return |
| * the value for VHT CAP: nsts-1) |
| */ |
| if (nsts == 0) |
| return 3; |
| |
| return nsts; |
| } |
| |
| static int ath10k_mac_get_vht_cap_bf_sound_dim(struct ath10k *ar) |
| { |
| int sound_dim = ar->vht_cap_info; |
| |
| sound_dim &= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK; |
| sound_dim >>= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT; |
| |
| /* If the sounding dimension is not advertised by the firmware, |
| * let's use a default value of 1 |
| */ |
| if (sound_dim == 0) |
| return 1; |
| |
| return sound_dim; |
| } |
| |
| static struct ieee80211_sta_vht_cap ath10k_create_vht_cap(struct ath10k *ar) |
| { |
| struct ieee80211_sta_vht_cap vht_cap = {0}; |
| struct ath10k_hw_params *hw = &ar->hw_params; |
| u16 mcs_map; |
| u32 val; |
| int i; |
| |
| vht_cap.vht_supported = 1; |
| vht_cap.cap = ar->vht_cap_info; |
| |
| if (ar->vht_cap_info & (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE)) { |
| val = ath10k_mac_get_vht_cap_bf_sts(ar); |
| val <<= IEEE80211_VHT_CAP_BEAMFORMEE_STS_SHIFT; |
| val &= IEEE80211_VHT_CAP_BEAMFORMEE_STS_MASK; |
| |
| vht_cap.cap |= val; |
| } |
| |
| if (ar->vht_cap_info & (IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE)) { |
| val = ath10k_mac_get_vht_cap_bf_sound_dim(ar); |
| val <<= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_SHIFT; |
| val &= IEEE80211_VHT_CAP_SOUNDING_DIMENSIONS_MASK; |
| |
| vht_cap.cap |= val; |
| } |
| |
| mcs_map = 0; |
| for (i = 0; i < 8; i++) { |
| if ((i < ar->num_rf_chains) && (ar->cfg_tx_chainmask & BIT(i))) |
| mcs_map |= IEEE80211_VHT_MCS_SUPPORT_0_9 << (i * 2); |
| else |
| mcs_map |= IEEE80211_VHT_MCS_NOT_SUPPORTED << (i * 2); |
| } |
| |
| if (ar->cfg_tx_chainmask <= 1) |
| vht_cap.cap &= ~IEEE80211_VHT_CAP_TXSTBC; |
| |
| vht_cap.vht_mcs.rx_mcs_map = cpu_to_le16(mcs_map); |
| vht_cap.vht_mcs.tx_mcs_map = cpu_to_le16(mcs_map); |
| |
| /* If we are supporting 160Mhz or 80+80, then the NIC may be able to do |
| * a restricted NSS for 160 or 80+80 vs what it can do for 80Mhz. Give |
| * user-space a clue if that is the case. |
| */ |
| if ((vht_cap.cap & IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_MASK) && |
| (hw->vht160_mcs_rx_highest != 0 || |
| hw->vht160_mcs_tx_highest != 0)) { |
| vht_cap.vht_mcs.rx_highest = cpu_to_le16(hw->vht160_mcs_rx_highest); |
| vht_cap.vht_mcs.tx_highest = cpu_to_le16(hw->vht160_mcs_tx_highest); |
| } |
| |
| return vht_cap; |
| } |
| |
| static struct ieee80211_sta_ht_cap ath10k_get_ht_cap(struct ath10k *ar) |
| { |
| int i; |
| struct ieee80211_sta_ht_cap ht_cap = {0}; |
| |
| if (!(ar->ht_cap_info & WMI_HT_CAP_ENABLED)) |
| return ht_cap; |
| |
| ht_cap.ht_supported = 1; |
| ht_cap.ampdu_factor = IEEE80211_HT_MAX_AMPDU_64K; |
| ht_cap.ampdu_density = IEEE80211_HT_MPDU_DENSITY_8; |
| ht_cap.cap |= IEEE80211_HT_CAP_SUP_WIDTH_20_40; |
| ht_cap.cap |= IEEE80211_HT_CAP_DSSSCCK40; |
| ht_cap.cap |= |
| WLAN_HT_CAP_SM_PS_DISABLED << IEEE80211_HT_CAP_SM_PS_SHIFT; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_HT20_SGI) |
| ht_cap.cap |= IEEE80211_HT_CAP_SGI_20; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_HT40_SGI) |
| ht_cap.cap |= IEEE80211_HT_CAP_SGI_40; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_DYNAMIC_SMPS) { |
| u32 smps; |
| |
| smps = WLAN_HT_CAP_SM_PS_DYNAMIC; |
| smps <<= IEEE80211_HT_CAP_SM_PS_SHIFT; |
| |
| ht_cap.cap |= smps; |
| } |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_TX_STBC && (ar->cfg_tx_chainmask > 1)) |
| ht_cap.cap |= IEEE80211_HT_CAP_TX_STBC; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_RX_STBC) { |
| u32 stbc; |
| |
| stbc = ar->ht_cap_info; |
| stbc &= WMI_HT_CAP_RX_STBC; |
| stbc >>= WMI_HT_CAP_RX_STBC_MASK_SHIFT; |
| stbc <<= IEEE80211_HT_CAP_RX_STBC_SHIFT; |
| stbc &= IEEE80211_HT_CAP_RX_STBC; |
| |
| ht_cap.cap |= stbc; |
| } |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_LDPC || (ar->ht_cap_info & |
| WMI_HT_CAP_RX_LDPC && (ar->ht_cap_info & WMI_HT_CAP_TX_LDPC))) |
| ht_cap.cap |= IEEE80211_HT_CAP_LDPC_CODING; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_L_SIG_TXOP_PROT) |
| ht_cap.cap |= IEEE80211_HT_CAP_LSIG_TXOP_PROT; |
| |
| /* max AMSDU is implicitly taken from vht_cap_info */ |
| if (ar->vht_cap_info & WMI_VHT_CAP_MAX_MPDU_LEN_MASK) |
| ht_cap.cap |= IEEE80211_HT_CAP_MAX_AMSDU; |
| |
| for (i = 0; i < ar->num_rf_chains; i++) { |
| if (ar->cfg_rx_chainmask & BIT(i)) |
| ht_cap.mcs.rx_mask[i] = 0xFF; |
| } |
| |
| ht_cap.mcs.tx_params |= IEEE80211_HT_MCS_TX_DEFINED; |
| |
| return ht_cap; |
| } |
| |
| static void ath10k_mac_setup_ht_vht_cap(struct ath10k *ar) |
| { |
| struct ieee80211_supported_band *band; |
| struct ieee80211_sta_vht_cap vht_cap; |
| struct ieee80211_sta_ht_cap ht_cap; |
| |
| ht_cap = ath10k_get_ht_cap(ar); |
| vht_cap = ath10k_create_vht_cap(ar); |
| |
| if (ar->phy_capability & WHAL_WLAN_11G_CAPABILITY) { |
| band = &ar->mac.sbands[NL80211_BAND_2GHZ]; |
| band->ht_cap = ht_cap; |
| } |
| if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) { |
| band = &ar->mac.sbands[NL80211_BAND_5GHZ]; |
| band->ht_cap = ht_cap; |
| band->vht_cap = vht_cap; |
| } |
| } |
| |
| static int __ath10k_set_antenna(struct ath10k *ar, u32 tx_ant, u32 rx_ant) |
| { |
| int ret; |
| bool is_valid_tx_chain_mask, is_valid_rx_chain_mask; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| is_valid_tx_chain_mask = ath10k_check_chain_mask(ar, tx_ant, "tx"); |
| is_valid_rx_chain_mask = ath10k_check_chain_mask(ar, rx_ant, "rx"); |
| |
| if (!is_valid_tx_chain_mask || !is_valid_rx_chain_mask) |
| return -EINVAL; |
| |
| ar->cfg_tx_chainmask = tx_ant; |
| ar->cfg_rx_chainmask = rx_ant; |
| |
| if ((ar->state != ATH10K_STATE_ON) && |
| (ar->state != ATH10K_STATE_RESTARTED)) |
| return 0; |
| |
| ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->tx_chain_mask, |
| tx_ant); |
| if (ret) { |
| ath10k_warn(ar, "failed to set tx-chainmask: %d, req 0x%x\n", |
| ret, tx_ant); |
| return ret; |
| } |
| |
| ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->rx_chain_mask, |
| rx_ant); |
| if (ret) { |
| ath10k_warn(ar, "failed to set rx-chainmask: %d, req 0x%x\n", |
| ret, rx_ant); |
| return ret; |
| } |
| |
| /* Reload HT/VHT capability */ |
| ath10k_mac_setup_ht_vht_cap(ar); |
| |
| return 0; |
| } |
| |
| static int ath10k_set_antenna(struct ieee80211_hw *hw, u32 tx_ant, u32 rx_ant) |
| { |
| struct ath10k *ar = hw->priv; |
| int ret; |
| |
| mutex_lock(&ar->conf_mutex); |
| ret = __ath10k_set_antenna(ar, tx_ant, rx_ant); |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static int __ath10k_fetch_bb_timing_dt(struct ath10k *ar, |
| struct wmi_bb_timing_cfg_arg *bb_timing) |
| { |
| struct device_node *node; |
| const char *fem_name; |
| int ret; |
| |
| node = ar->dev->of_node; |
| if (!node) |
| return -ENOENT; |
| |
| ret = of_property_read_string_index(node, "ext-fem-name", 0, &fem_name); |
| if (ret) |
| return -ENOENT; |
| |
| /* |
| * If external Front End module used in hardware, then default base band timing |
| * parameter cannot be used since they were fine tuned for reference hardware, |
| * so choosing different value suitable for that external FEM. |
| */ |
| if (!strcmp("microsemi-lx5586", fem_name)) { |
| bb_timing->bb_tx_timing = 0x00; |
| bb_timing->bb_xpa_timing = 0x0101; |
| } else { |
| return -ENOENT; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, "boot bb_tx_timing 0x%x bb_xpa_timing 0x%x\n", |
| bb_timing->bb_tx_timing, bb_timing->bb_xpa_timing); |
| return 0; |
| } |
| |
| static int ath10k_mac_rfkill_config(struct ath10k *ar) |
| { |
| u32 param; |
| int ret; |
| |
| if (ar->hw_values->rfkill_pin == 0) { |
| ath10k_warn(ar, "ath10k does not support hardware rfkill with this device\n"); |
| return -EOPNOTSUPP; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac rfkill_pin %d rfkill_cfg %d rfkill_on_level %d", |
| ar->hw_values->rfkill_pin, ar->hw_values->rfkill_cfg, |
| ar->hw_values->rfkill_on_level); |
| |
| param = FIELD_PREP(WMI_TLV_RFKILL_CFG_RADIO_LEVEL, |
| ar->hw_values->rfkill_on_level) | |
| FIELD_PREP(WMI_TLV_RFKILL_CFG_GPIO_PIN_NUM, |
| ar->hw_values->rfkill_pin) | |
| FIELD_PREP(WMI_TLV_RFKILL_CFG_PIN_AS_GPIO, |
| ar->hw_values->rfkill_cfg); |
| |
| ret = ath10k_wmi_pdev_set_param(ar, |
| ar->wmi.pdev_param->rfkill_config, |
| param); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to set rfkill config 0x%x: %d\n", |
| param, ret); |
| return ret; |
| } |
| return 0; |
| } |
| |
| int ath10k_mac_rfkill_enable_radio(struct ath10k *ar, bool enable) |
| { |
| enum wmi_tlv_rfkill_enable_radio param; |
| int ret; |
| |
| if (enable) |
| param = WMI_TLV_RFKILL_ENABLE_RADIO_ON; |
| else |
| param = WMI_TLV_RFKILL_ENABLE_RADIO_OFF; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac rfkill enable %d", param); |
| |
| ret = ath10k_wmi_pdev_set_param(ar, ar->wmi.pdev_param->rfkill_enable, |
| param); |
| if (ret) { |
| ath10k_warn(ar, "failed to set rfkill enable param %d: %d\n", |
| param, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static int ath10k_start(struct ieee80211_hw *hw) |
| { |
| struct ath10k *ar = hw->priv; |
| u32 param; |
| int ret = 0; |
| struct wmi_bb_timing_cfg_arg bb_timing = {0}; |
| |
| /* |
| * This makes sense only when restarting hw. It is harmless to call |
| * unconditionally. This is necessary to make sure no HTT/WMI tx |
| * commands will be submitted while restarting. |
| */ |
| ath10k_drain_tx(ar); |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| switch (ar->state) { |
| case ATH10K_STATE_OFF: |
| ar->state = ATH10K_STATE_ON; |
| break; |
| case ATH10K_STATE_RESTARTING: |
| ar->state = ATH10K_STATE_RESTARTED; |
| break; |
| case ATH10K_STATE_ON: |
| case ATH10K_STATE_RESTARTED: |
| case ATH10K_STATE_WEDGED: |
| WARN_ON(1); |
| ret = -EINVAL; |
| goto err; |
| case ATH10K_STATE_UTF: |
| ret = -EBUSY; |
| goto err; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| if (ar->hw_rfkill_on) { |
| ar->hw_rfkill_on = false; |
| spin_unlock_bh(&ar->data_lock); |
| goto err; |
| } |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| ret = ath10k_hif_power_up(ar, ATH10K_FIRMWARE_MODE_NORMAL); |
| if (ret) { |
| ath10k_err(ar, "Could not init hif: %d\n", ret); |
| goto err_off; |
| } |
| |
| ret = ath10k_core_start(ar, ATH10K_FIRMWARE_MODE_NORMAL, |
| &ar->normal_mode_fw); |
| if (ret) { |
| ath10k_err(ar, "Could not init core: %d\n", ret); |
| goto err_power_down; |
| } |
| |
| if (ar->sys_cap_info & WMI_TLV_SYS_CAP_INFO_RFKILL) { |
| ret = ath10k_mac_rfkill_config(ar); |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "failed to configure rfkill: %d", ret); |
| goto err_core_stop; |
| } |
| } |
| |
| param = ar->wmi.pdev_param->pmf_qos; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 1); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable PMF QOS: %d\n", ret); |
| goto err_core_stop; |
| } |
| |
| param = ar->wmi.pdev_param->dynamic_bw; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 1); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable dynamic BW: %d\n", ret); |
| goto err_core_stop; |
| } |
| |
| if (test_bit(WMI_SERVICE_SPOOF_MAC_SUPPORT, ar->wmi.svc_map)) { |
| ret = ath10k_wmi_scan_prob_req_oui(ar, ar->mac_addr); |
| if (ret) { |
| ath10k_err(ar, "failed to set prob req oui: %i\n", ret); |
| goto err_core_stop; |
| } |
| } |
| |
| if (test_bit(WMI_SERVICE_ADAPTIVE_OCS, ar->wmi.svc_map)) { |
| ret = ath10k_wmi_adaptive_qcs(ar, true); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable adaptive qcs: %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| } |
| |
| if (test_bit(WMI_SERVICE_BURST, ar->wmi.svc_map)) { |
| param = ar->wmi.pdev_param->burst_enable; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 0); |
| if (ret) { |
| ath10k_warn(ar, "failed to disable burst: %d\n", ret); |
| goto err_core_stop; |
| } |
| } |
| |
| param = ar->wmi.pdev_param->idle_ps_config; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 1); |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "failed to enable idle_ps_config: %d\n", ret); |
| goto err_core_stop; |
| } |
| |
| __ath10k_set_antenna(ar, ar->cfg_tx_chainmask, ar->cfg_rx_chainmask); |
| |
| /* |
| * By default FW set ARP frames ac to voice (6). In that case ARP |
| * exchange is not working properly for UAPSD enabled AP. ARP requests |
| * which arrives with access category 0 are processed by network stack |
| * and send back with access category 0, but FW changes access category |
| * to 6. Set ARP frames access category to best effort (0) solves |
| * this problem. |
| */ |
| |
| param = ar->wmi.pdev_param->arp_ac_override; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 0); |
| if (ret) { |
| ath10k_warn(ar, "failed to set arp ac override parameter: %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| |
| if (test_bit(ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA, |
| ar->running_fw->fw_file.fw_features)) { |
| ret = ath10k_wmi_pdev_enable_adaptive_cca(ar, 1, |
| WMI_CCA_DETECT_LEVEL_AUTO, |
| WMI_CCA_DETECT_MARGIN_AUTO); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable adaptive cca: %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| } |
| |
| param = ar->wmi.pdev_param->ani_enable; |
| ret = ath10k_wmi_pdev_set_param(ar, param, 1); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable ani by default: %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| |
| ar->ani_enabled = true; |
| |
| if (ath10k_peer_stats_enabled(ar)) { |
| param = ar->wmi.pdev_param->peer_stats_update_period; |
| ret = ath10k_wmi_pdev_set_param(ar, param, |
| PEER_DEFAULT_STATS_UPDATE_PERIOD); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to set peer stats period : %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| } |
| |
| param = ar->wmi.pdev_param->enable_btcoex; |
| if (test_bit(WMI_SERVICE_COEX_GPIO, ar->wmi.svc_map) && |
| test_bit(ATH10K_FW_FEATURE_BTCOEX_PARAM, |
| ar->running_fw->fw_file.fw_features) && |
| ar->coex_support) { |
| ret = ath10k_wmi_pdev_set_param(ar, param, 0); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to set btcoex param: %d\n", ret); |
| goto err_core_stop; |
| } |
| clear_bit(ATH10K_FLAG_BTCOEX, &ar->dev_flags); |
| } |
| |
| if (test_bit(WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT, ar->wmi.svc_map)) { |
| ret = __ath10k_fetch_bb_timing_dt(ar, &bb_timing); |
| if (!ret) { |
| ret = ath10k_wmi_pdev_bb_timing(ar, &bb_timing); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to set bb timings: %d\n", |
| ret); |
| goto err_core_stop; |
| } |
| } |
| } |
| |
| ar->num_started_vdevs = 0; |
| ath10k_regd_update(ar); |
| |
| ath10k_spectral_start(ar); |
| ath10k_thermal_set_throttling(ar); |
| |
| ar->radar_conf_state = ATH10K_RADAR_CONFIRMATION_IDLE; |
| |
| mutex_unlock(&ar->conf_mutex); |
| return 0; |
| |
| err_core_stop: |
| ath10k_core_stop(ar); |
| |
| err_power_down: |
| ath10k_hif_power_down(ar); |
| |
| err_off: |
| ar->state = ATH10K_STATE_OFF; |
| |
| err: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static void ath10k_stop(struct ieee80211_hw *hw, bool suspend) |
| { |
| struct ath10k *ar = hw->priv; |
| u32 opt; |
| |
| ath10k_drain_tx(ar); |
| |
| mutex_lock(&ar->conf_mutex); |
| if (ar->state != ATH10K_STATE_OFF) { |
| if (!ar->hw_rfkill_on) { |
| /* If the current driver state is RESTARTING but not yet |
| * fully RESTARTED because of incoming suspend event, |
| * then ath10k_halt() is already called via |
| * ath10k_core_restart() and should not be called here. |
| */ |
| if (ar->state != ATH10K_STATE_RESTARTING) { |
| ath10k_halt(ar); |
| } else { |
| /* Suspending here, because when in RESTARTING |
| * state, ath10k_core_stop() skips |
| * ath10k_wait_for_suspend(). |
| */ |
| opt = WMI_PDEV_SUSPEND_AND_DISABLE_INTR; |
| ath10k_wait_for_suspend(ar, opt); |
| } |
| } |
| ar->state = ATH10K_STATE_OFF; |
| } |
| mutex_unlock(&ar->conf_mutex); |
| |
| cancel_work_sync(&ar->set_coverage_class_work); |
| cancel_delayed_work_sync(&ar->scan.timeout); |
| cancel_work_sync(&ar->restart_work); |
| } |
| |
| static int ath10k_config_ps(struct ath10k *ar) |
| { |
| struct ath10k_vif *arvif; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| ret = ath10k_mac_vif_setup_ps(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to setup powersave: %d\n", ret); |
| break; |
| } |
| } |
| |
| return ret; |
| } |
| |
| static int ath10k_config(struct ieee80211_hw *hw, u32 changed) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ieee80211_conf *conf = &hw->conf; |
| int ret = 0; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (changed & IEEE80211_CONF_CHANGE_PS) |
| ath10k_config_ps(ar); |
| |
| if (changed & IEEE80211_CONF_CHANGE_MONITOR) { |
| ar->monitor = conf->flags & IEEE80211_CONF_MONITOR; |
| ret = ath10k_monitor_recalc(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to recalc monitor: %d\n", ret); |
| } |
| |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static u32 get_nss_from_chainmask(u16 chain_mask) |
| { |
| if ((chain_mask & 0xf) == 0xf) |
| return 4; |
| else if ((chain_mask & 0x7) == 0x7) |
| return 3; |
| else if ((chain_mask & 0x3) == 0x3) |
| return 2; |
| return 1; |
| } |
| |
| static int ath10k_mac_set_txbf_conf(struct ath10k_vif *arvif) |
| { |
| u32 value = 0; |
| struct ath10k *ar = arvif->ar; |
| int nsts; |
| int sound_dim; |
| |
| if (ath10k_wmi_get_txbf_conf_scheme(ar) != WMI_TXBF_CONF_BEFORE_ASSOC) |
| return 0; |
| |
| nsts = ath10k_mac_get_vht_cap_bf_sts(ar); |
| if (ar->vht_cap_info & (IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE)) |
| value |= SM(nsts, WMI_TXBF_STS_CAP_OFFSET); |
| |
| sound_dim = ath10k_mac_get_vht_cap_bf_sound_dim(ar); |
| if (ar->vht_cap_info & (IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE | |
| IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE)) |
| value |= SM(sound_dim, WMI_BF_SOUND_DIM_OFFSET); |
| |
| if (!value) |
| return 0; |
| |
| if (ar->vht_cap_info & IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFER; |
| |
| if (ar->vht_cap_info & IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE) |
| value |= (WMI_VDEV_PARAM_TXBF_MU_TX_BFER | |
| WMI_VDEV_PARAM_TXBF_SU_TX_BFER); |
| |
| if (ar->vht_cap_info & IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE) |
| value |= WMI_VDEV_PARAM_TXBF_SU_TX_BFEE; |
| |
| if (ar->vht_cap_info & IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE) |
| value |= (WMI_VDEV_PARAM_TXBF_MU_TX_BFEE | |
| WMI_VDEV_PARAM_TXBF_SU_TX_BFEE); |
| |
| return ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, |
| ar->wmi.vdev_param->txbf, value); |
| } |
| |
| static void ath10k_update_vif_offload(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k *ar = hw->priv; |
| u32 vdev_param; |
| int ret; |
| |
| if (ath10k_frame_mode != ATH10K_HW_TXRX_ETHERNET || |
| ar->wmi.vdev_param->tx_encap_type == WMI_VDEV_PARAM_UNSUPPORTED || |
| (vif->type != NL80211_IFTYPE_STATION && |
| vif->type != NL80211_IFTYPE_AP)) |
| vif->offload_flags &= ~IEEE80211_OFFLOAD_ENCAP_ENABLED; |
| |
| vdev_param = ar->wmi.vdev_param->tx_encap_type; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| ATH10K_HW_TXRX_NATIVE_WIFI); |
| /* 10.X firmware does not support this VDEV parameter. Do not warn */ |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "failed to set vdev %i TX encapsulation: %d\n", |
| arvif->vdev_id, ret); |
| } |
| } |
| |
| /* |
| * TODO: |
| * Figure out how to handle WMI_VDEV_SUBTYPE_P2P_DEVICE, |
| * because we will send mgmt frames without CCK. This requirement |
| * for P2P_FIND/GO_NEG should be handled by checking CCK flag |
| * in the TX packet. |
| */ |
| static int ath10k_add_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_peer *peer; |
| enum wmi_sta_powersave_param param; |
| int ret = 0; |
| u32 value; |
| int bit; |
| int i; |
| u32 vdev_param; |
| |
| vif->driver_flags |= IEEE80211_VIF_SUPPORTS_UAPSD; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| memset(arvif, 0, sizeof(*arvif)); |
| ath10k_mac_txq_init(vif->txq); |
| |
| arvif->ar = ar; |
| arvif->vif = vif; |
| |
| INIT_LIST_HEAD(&arvif->list); |
| INIT_WORK(&arvif->ap_csa_work, ath10k_mac_vif_ap_csa_work); |
| INIT_DELAYED_WORK(&arvif->connection_loss_work, |
| ath10k_mac_vif_sta_connection_loss_work); |
| |
| for (i = 0; i < ARRAY_SIZE(arvif->bitrate_mask.control); i++) { |
| arvif->bitrate_mask.control[i].legacy = 0xffffffff; |
| memset(arvif->bitrate_mask.control[i].ht_mcs, 0xff, |
| sizeof(arvif->bitrate_mask.control[i].ht_mcs)); |
| memset(arvif->bitrate_mask.control[i].vht_mcs, 0xff, |
| sizeof(arvif->bitrate_mask.control[i].vht_mcs)); |
| } |
| |
| if (ar->num_peers >= ar->max_num_peers) { |
| ath10k_warn(ar, "refusing vdev creation due to insufficient peer entry resources in firmware\n"); |
| ret = -ENOBUFS; |
| goto err; |
| } |
| |
| if (ar->free_vdev_map == 0) { |
| ath10k_warn(ar, "Free vdev map is empty, no more interfaces allowed.\n"); |
| ret = -EBUSY; |
| goto err; |
| } |
| bit = __ffs64(ar->free_vdev_map); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac create vdev %i map %llx\n", |
| bit, ar->free_vdev_map); |
| |
| arvif->vdev_id = bit; |
| arvif->vdev_subtype = |
| ath10k_wmi_get_vdev_subtype(ar, WMI_VDEV_SUBTYPE_NONE); |
| |
| switch (vif->type) { |
| case NL80211_IFTYPE_P2P_DEVICE: |
| arvif->vdev_type = WMI_VDEV_TYPE_STA; |
| arvif->vdev_subtype = ath10k_wmi_get_vdev_subtype |
| (ar, WMI_VDEV_SUBTYPE_P2P_DEVICE); |
| break; |
| case NL80211_IFTYPE_UNSPECIFIED: |
| case NL80211_IFTYPE_STATION: |
| arvif->vdev_type = WMI_VDEV_TYPE_STA; |
| if (vif->p2p) |
| arvif->vdev_subtype = ath10k_wmi_get_vdev_subtype |
| (ar, WMI_VDEV_SUBTYPE_P2P_CLIENT); |
| break; |
| case NL80211_IFTYPE_ADHOC: |
| arvif->vdev_type = WMI_VDEV_TYPE_IBSS; |
| break; |
| case NL80211_IFTYPE_MESH_POINT: |
| if (test_bit(WMI_SERVICE_MESH_11S, ar->wmi.svc_map)) { |
| arvif->vdev_subtype = ath10k_wmi_get_vdev_subtype |
| (ar, WMI_VDEV_SUBTYPE_MESH_11S); |
| } else if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { |
| ret = -EINVAL; |
| ath10k_warn(ar, "must load driver with rawmode=1 to add mesh interfaces\n"); |
| goto err; |
| } |
| arvif->vdev_type = WMI_VDEV_TYPE_AP; |
| break; |
| case NL80211_IFTYPE_AP: |
| arvif->vdev_type = WMI_VDEV_TYPE_AP; |
| |
| if (vif->p2p) |
| arvif->vdev_subtype = ath10k_wmi_get_vdev_subtype |
| (ar, WMI_VDEV_SUBTYPE_P2P_GO); |
| break; |
| case NL80211_IFTYPE_MONITOR: |
| arvif->vdev_type = WMI_VDEV_TYPE_MONITOR; |
| break; |
| default: |
| WARN_ON(1); |
| break; |
| } |
| |
| /* Using vdev_id as queue number will make it very easy to do per-vif |
| * tx queue locking. This shouldn't wrap due to interface combinations |
| * but do a modulo for correctness sake and prevent using offchannel tx |
| * queues for regular vif tx. |
| */ |
| vif->cab_queue = arvif->vdev_id % (IEEE80211_MAX_QUEUES - 1); |
| for (i = 0; i < ARRAY_SIZE(vif->hw_queue); i++) |
| vif->hw_queue[i] = arvif->vdev_id % (IEEE80211_MAX_QUEUES - 1); |
| |
| /* Some firmware revisions don't wait for beacon tx completion before |
| * sending another SWBA event. This could lead to hardware using old |
| * (freed) beacon data in some cases, e.g. tx credit starvation |
| * combined with missed TBTT. This is very rare. |
| * |
| * On non-IOMMU-enabled hosts this could be a possible security issue |
| * because hw could beacon some random data on the air. On |
| * IOMMU-enabled hosts DMAR faults would occur in most cases and target |
| * device would crash. |
| * |
| * Since there are no beacon tx completions (implicit nor explicit) |
| * propagated to host the only workaround for this is to allocate a |
| * DMA-coherent buffer for a lifetime of a vif and use it for all |
| * beacon tx commands. Worst case for this approach is some beacons may |
| * become corrupted, e.g. have garbled IEs or out-of-date TIM bitmap. |
| */ |
| if (vif->type == NL80211_IFTYPE_ADHOC || |
| vif->type == NL80211_IFTYPE_MESH_POINT || |
| vif->type == NL80211_IFTYPE_AP) { |
| if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL) { |
| arvif->beacon_buf = kmalloc(IEEE80211_MAX_FRAME_LEN, |
| GFP_KERNEL); |
| |
| /* Using a kernel pointer in place of a dma_addr_t |
| * token can lead to undefined behavior if that |
| * makes it into cache management functions. Use a |
| * known-invalid address token instead, which |
| * avoids the warning and makes it easier to catch |
| * bugs if it does end up getting used. |
| */ |
| arvif->beacon_paddr = DMA_MAPPING_ERROR; |
| } else { |
| arvif->beacon_buf = |
| dma_alloc_coherent(ar->dev, |
| IEEE80211_MAX_FRAME_LEN, |
| &arvif->beacon_paddr, |
| GFP_ATOMIC); |
| } |
| if (!arvif->beacon_buf) { |
| ret = -ENOMEM; |
| ath10k_warn(ar, "failed to allocate beacon buffer: %d\n", |
| ret); |
| goto err; |
| } |
| } |
| if (test_bit(ATH10K_FLAG_HW_CRYPTO_DISABLED, &ar->dev_flags)) |
| arvif->nohwcrypt = true; |
| |
| if (arvif->nohwcrypt && |
| !test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) { |
| ret = -EINVAL; |
| ath10k_warn(ar, "cryptmode module param needed for sw crypto\n"); |
| goto err; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev create %d (add interface) type %d subtype %d bcnmode %s\n", |
| arvif->vdev_id, arvif->vdev_type, arvif->vdev_subtype, |
| arvif->beacon_buf ? "single-buf" : "per-skb"); |
| |
| ret = ath10k_wmi_vdev_create(ar, arvif->vdev_id, arvif->vdev_type, |
| arvif->vdev_subtype, vif->addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to create WMI vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto err; |
| } |
| |
| if (test_bit(WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT, |
| ar->wmi.svc_map)) { |
| vdev_param = ar->wmi.vdev_param->disable_4addr_src_lrn; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| WMI_VDEV_DISABLE_4_ADDR_SRC_LRN); |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "failed to disable 4addr src lrn vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| } |
| } |
| |
| ar->free_vdev_map &= ~(1LL << arvif->vdev_id); |
| spin_lock_bh(&ar->data_lock); |
| list_add(&arvif->list, &ar->arvifs); |
| spin_unlock_bh(&ar->data_lock); |
| |
| /* It makes no sense to have firmware do keepalives. mac80211 already |
| * takes care of this with idle connection polling. |
| */ |
| ret = ath10k_mac_vif_disable_keepalive(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to disable keepalive on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto err_vdev_delete; |
| } |
| |
| arvif->def_wep_key_idx = -1; |
| |
| ath10k_update_vif_offload(hw, vif); |
| |
| /* Configuring number of spatial stream for monitor interface is causing |
| * target assert in qca9888 and qca6174. |
| */ |
| if (ar->cfg_tx_chainmask && (vif->type != NL80211_IFTYPE_MONITOR)) { |
| u16 nss = get_nss_from_chainmask(ar->cfg_tx_chainmask); |
| |
| vdev_param = ar->wmi.vdev_param->nss; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| nss); |
| if (ret) { |
| ath10k_warn(ar, "failed to set vdev %i chainmask 0x%x, nss %i: %d\n", |
| arvif->vdev_id, ar->cfg_tx_chainmask, nss, |
| ret); |
| goto err_vdev_delete; |
| } |
| } |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP || |
| arvif->vdev_type == WMI_VDEV_TYPE_IBSS) { |
| ret = ath10k_peer_create(ar, vif, NULL, arvif->vdev_id, |
| vif->addr, WMI_PEER_TYPE_DEFAULT); |
| if (ret) { |
| ath10k_warn(ar, "failed to create vdev %i peer for AP/IBSS: %d\n", |
| arvif->vdev_id, ret); |
| goto err_vdev_delete; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| peer = ath10k_peer_find(ar, arvif->vdev_id, vif->addr); |
| if (!peer) { |
| ath10k_warn(ar, "failed to lookup peer %pM on vdev %i\n", |
| vif->addr, arvif->vdev_id); |
| spin_unlock_bh(&ar->data_lock); |
| ret = -ENOENT; |
| goto err_peer_delete; |
| } |
| |
| arvif->peer_id = find_first_bit(peer->peer_ids, |
| ATH10K_MAX_NUM_PEER_IDS); |
| |
| spin_unlock_bh(&ar->data_lock); |
| } else { |
| arvif->peer_id = HTT_INVALID_PEERID; |
| } |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP) { |
| ret = ath10k_mac_set_kickout(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to set vdev %i kickout parameters: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| } |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_STA) { |
| param = WMI_STA_PS_PARAM_RX_WAKE_POLICY; |
| value = WMI_STA_PS_RX_WAKE_POLICY_WAKE; |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, |
| param, value); |
| if (ret) { |
| ath10k_warn(ar, "failed to set vdev %i RX wake policy: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| |
| ret = ath10k_mac_vif_recalc_ps_wake_threshold(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc ps wake threshold on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| |
| ret = ath10k_mac_vif_recalc_ps_poll_count(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc ps poll count on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| } |
| |
| ret = ath10k_mac_set_txbf_conf(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to set txbf for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| |
| ret = ath10k_mac_set_rts(arvif, ar->hw->wiphy->rts_threshold); |
| if (ret) { |
| ath10k_warn(ar, "failed to set rts threshold for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| goto err_peer_delete; |
| } |
| |
| arvif->txpower = vif->bss_conf.txpower; |
| ret = ath10k_mac_txpower_recalc(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc tx power: %d\n", ret); |
| goto err_peer_delete; |
| } |
| |
| if (test_bit(WMI_SERVICE_RTT_RESPONDER_ROLE, ar->wmi.svc_map)) { |
| vdev_param = ar->wmi.vdev_param->rtt_responder_role; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| arvif->ftm_responder); |
| |
| /* It is harmless to not set FTM role. Do not warn */ |
| if (ret && ret != -EOPNOTSUPP) |
| ath10k_warn(ar, "failed to set vdev %i FTM Responder: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (vif->type == NL80211_IFTYPE_MONITOR) { |
| ar->monitor_arvif = arvif; |
| ret = ath10k_monitor_recalc(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc monitor: %d\n", ret); |
| goto err_peer_delete; |
| } |
| } |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| if (!ar->tx_paused) |
| ieee80211_wake_queue(ar->hw, arvif->vdev_id); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| mutex_unlock(&ar->conf_mutex); |
| return 0; |
| |
| err_peer_delete: |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP || |
| arvif->vdev_type == WMI_VDEV_TYPE_IBSS) { |
| ath10k_wmi_peer_delete(ar, arvif->vdev_id, vif->addr); |
| ath10k_wait_for_peer_delete_done(ar, arvif->vdev_id, |
| vif->addr); |
| } |
| |
| err_vdev_delete: |
| ath10k_wmi_vdev_delete(ar, arvif->vdev_id); |
| ar->free_vdev_map |= 1LL << arvif->vdev_id; |
| spin_lock_bh(&ar->data_lock); |
| list_del(&arvif->list); |
| spin_unlock_bh(&ar->data_lock); |
| |
| err: |
| if (arvif->beacon_buf) { |
| if (ar->bus_param.dev_type == ATH10K_DEV_TYPE_HL) |
| kfree(arvif->beacon_buf); |
| else |
| dma_free_coherent(ar->dev, IEEE80211_MAX_FRAME_LEN, |
| arvif->beacon_buf, |
| arvif->beacon_paddr); |
| arvif->beacon_buf = NULL; |
| } |
| |
| mutex_unlock(&ar->conf_mutex); |
| |
| return ret; |
| } |
| |
| static void ath10k_mac_vif_tx_unlock_all(struct ath10k_vif *arvif) |
| { |
| int i; |
| |
| for (i = 0; i < BITS_PER_LONG; i++) |
| ath10k_mac_vif_tx_unlock(arvif, i); |
| } |
| |
| static void ath10k_remove_interface(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_peer *peer; |
| unsigned long time_left; |
| int ret; |
| int i; |
| |
| cancel_work_sync(&arvif->ap_csa_work); |
| cancel_delayed_work_sync(&arvif->connection_loss_work); |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ret = ath10k_spectral_vif_stop(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to stop spectral for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| ar->free_vdev_map |= 1LL << arvif->vdev_id; |
| spin_lock_bh(&ar->data_lock); |
| list_del(&arvif->list); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP || |
| arvif->vdev_type == WMI_VDEV_TYPE_IBSS) { |
| ret = ath10k_wmi_peer_delete(arvif->ar, arvif->vdev_id, |
| vif->addr); |
| if (ret) |
| ath10k_warn(ar, "failed to submit AP/IBSS self-peer removal on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| ath10k_wait_for_peer_delete_done(ar, arvif->vdev_id, |
| vif->addr); |
| kfree(arvif->u.ap.noa_data); |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %i delete (remove interface)\n", |
| arvif->vdev_id); |
| |
| ret = ath10k_wmi_vdev_delete(ar, arvif->vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to delete WMI vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| if (test_bit(WMI_SERVICE_SYNC_DELETE_CMDS, ar->wmi.svc_map)) { |
| time_left = wait_for_completion_timeout(&ar->vdev_delete_done, |
| ATH10K_VDEV_DELETE_TIMEOUT_HZ); |
| if (time_left == 0) { |
| ath10k_warn(ar, "Timeout in receiving vdev delete response\n"); |
| goto out; |
| } |
| } |
| |
| /* Some firmware revisions don't notify host about self-peer removal |
| * until after associated vdev is deleted. |
| */ |
| if (arvif->vdev_type == WMI_VDEV_TYPE_AP || |
| arvif->vdev_type == WMI_VDEV_TYPE_IBSS) { |
| ret = ath10k_wait_for_peer_deleted(ar, arvif->vdev_id, |
| vif->addr); |
| if (ret) |
| ath10k_warn(ar, "failed to remove AP self-peer on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| spin_lock_bh(&ar->data_lock); |
| ar->num_peers--; |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) { |
| peer = ar->peer_map[i]; |
| if (!peer) |
| continue; |
| |
| if (peer->vif == vif) { |
| ath10k_warn(ar, "found vif peer %pM entry on vdev %i after it was supposedly removed\n", |
| vif->addr, arvif->vdev_id); |
| peer->vif = NULL; |
| } |
| } |
| |
| /* Clean this up late, less opportunity for firmware to access |
| * DMA memory we have deleted. |
| */ |
| ath10k_mac_vif_beacon_cleanup(arvif); |
| spin_unlock_bh(&ar->data_lock); |
| |
| ath10k_peer_cleanup(ar, arvif->vdev_id); |
| ath10k_mac_txq_unref(ar, vif->txq); |
| |
| if (vif->type == NL80211_IFTYPE_MONITOR) { |
| ar->monitor_arvif = NULL; |
| ret = ath10k_monitor_recalc(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to recalc monitor: %d\n", ret); |
| } |
| |
| ret = ath10k_mac_txpower_recalc(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to recalc tx power: %d\n", ret); |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| ath10k_mac_vif_tx_unlock_all(arvif); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| ath10k_mac_txq_unref(ar, vif->txq); |
| |
| out: |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| /* |
| * FIXME: Has to be verified. |
| */ |
| #define SUPPORTED_FILTERS \ |
| (FIF_ALLMULTI | \ |
| FIF_CONTROL | \ |
| FIF_PSPOLL | \ |
| FIF_OTHER_BSS | \ |
| FIF_BCN_PRBRESP_PROMISC | \ |
| FIF_PROBE_REQ | \ |
| FIF_FCSFAIL) |
| |
| static void ath10k_configure_filter(struct ieee80211_hw *hw, |
| unsigned int changed_flags, |
| unsigned int *total_flags, |
| u64 multicast) |
| { |
| struct ath10k *ar = hw->priv; |
| int ret; |
| unsigned int supported = SUPPORTED_FILTERS; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (ar->hw_params.mcast_frame_registration) |
| supported |= FIF_MCAST_ACTION; |
| |
| *total_flags &= supported; |
| |
| ar->filter_flags = *total_flags; |
| |
| ret = ath10k_monitor_recalc(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to recalc monitor: %d\n", ret); |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static void ath10k_recalculate_mgmt_rate(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct cfg80211_chan_def *def) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| const struct ieee80211_supported_band *sband; |
| u8 basic_rate_idx; |
| int hw_rate_code; |
| u32 vdev_param; |
| u16 bitrate; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| sband = ar->hw->wiphy->bands[def->chan->band]; |
| basic_rate_idx = ffs(vif->bss_conf.basic_rates) - 1; |
| bitrate = sband->bitrates[basic_rate_idx].bitrate; |
| |
| hw_rate_code = ath10k_mac_get_rate_hw_value(bitrate); |
| if (hw_rate_code < 0) { |
| ath10k_warn(ar, "bitrate not supported %d\n", bitrate); |
| return; |
| } |
| |
| vdev_param = ar->wmi.vdev_param->mgmt_rate; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| hw_rate_code); |
| if (ret) |
| ath10k_warn(ar, "failed to set mgmt tx rate %d\n", ret); |
| } |
| |
| static void ath10k_bss_info_changed(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *info, |
| u64 changed) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct cfg80211_chan_def def; |
| u32 vdev_param, pdev_param, slottime, preamble; |
| u16 bitrate, hw_value; |
| u8 rate, rateidx; |
| int ret = 0, mcast_rate; |
| enum nl80211_band band; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (changed & BSS_CHANGED_IBSS) |
| ath10k_control_ibss(arvif, vif); |
| |
| if (changed & BSS_CHANGED_BEACON_INT) { |
| arvif->beacon_interval = info->beacon_int; |
| vdev_param = ar->wmi.vdev_param->beacon_interval; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| arvif->beacon_interval); |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d beacon_interval %d\n", |
| arvif->vdev_id, arvif->beacon_interval); |
| |
| if (ret) |
| ath10k_warn(ar, "failed to set beacon interval for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_BEACON) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "vdev %d set beacon tx mode to staggered\n", |
| arvif->vdev_id); |
| |
| pdev_param = ar->wmi.pdev_param->beacon_tx_mode; |
| ret = ath10k_wmi_pdev_set_param(ar, pdev_param, |
| WMI_BEACON_STAGGERED_MODE); |
| if (ret) |
| ath10k_warn(ar, "failed to set beacon mode for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| |
| ret = ath10k_mac_setup_bcn_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to update beacon template: %d\n", |
| ret); |
| |
| if (ieee80211_vif_is_mesh(vif)) { |
| /* mesh doesn't use SSID but firmware needs it */ |
| arvif->u.ap.ssid_len = 4; |
| memcpy(arvif->u.ap.ssid, "mesh", arvif->u.ap.ssid_len); |
| } |
| } |
| |
| if (changed & BSS_CHANGED_AP_PROBE_RESP) { |
| ret = ath10k_mac_setup_prb_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to setup probe resp template on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & (BSS_CHANGED_BEACON_INFO | BSS_CHANGED_BEACON)) { |
| arvif->dtim_period = info->dtim_period; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d dtim_period %d\n", |
| arvif->vdev_id, arvif->dtim_period); |
| |
| vdev_param = ar->wmi.vdev_param->dtim_period; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| arvif->dtim_period); |
| if (ret) |
| ath10k_warn(ar, "failed to set dtim period for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_SSID && |
| vif->type == NL80211_IFTYPE_AP) { |
| arvif->u.ap.ssid_len = vif->cfg.ssid_len; |
| if (vif->cfg.ssid_len) |
| memcpy(arvif->u.ap.ssid, vif->cfg.ssid, |
| vif->cfg.ssid_len); |
| arvif->u.ap.hidden_ssid = info->hidden_ssid; |
| } |
| |
| if (changed & BSS_CHANGED_BSSID && !is_zero_ether_addr(info->bssid)) |
| ether_addr_copy(arvif->bssid, info->bssid); |
| |
| if (changed & BSS_CHANGED_FTM_RESPONDER && |
| arvif->ftm_responder != info->ftm_responder && |
| test_bit(WMI_SERVICE_RTT_RESPONDER_ROLE, ar->wmi.svc_map)) { |
| arvif->ftm_responder = info->ftm_responder; |
| |
| vdev_param = ar->wmi.vdev_param->rtt_responder_role; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| arvif->ftm_responder); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d ftm_responder %d:ret %d\n", |
| arvif->vdev_id, arvif->ftm_responder, ret); |
| } |
| |
| if (changed & BSS_CHANGED_BEACON_ENABLED) |
| ath10k_control_beaconing(arvif, info); |
| |
| if (changed & BSS_CHANGED_ERP_CTS_PROT) { |
| arvif->use_cts_prot = info->use_cts_prot; |
| |
| ret = ath10k_recalc_rtscts_prot(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to recalculate rts/cts prot for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| |
| if (ath10k_mac_can_set_cts_prot(arvif)) { |
| ret = ath10k_mac_set_cts_prot(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to set cts protection for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| } |
| } |
| |
| if (changed & BSS_CHANGED_ERP_SLOT) { |
| if (info->use_short_slot) |
| slottime = WMI_VDEV_SLOT_TIME_SHORT; /* 9us */ |
| |
| else |
| slottime = WMI_VDEV_SLOT_TIME_LONG; /* 20us */ |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d slot_time %d\n", |
| arvif->vdev_id, slottime); |
| |
| vdev_param = ar->wmi.vdev_param->slot_time; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| slottime); |
| if (ret) |
| ath10k_warn(ar, "failed to set erp slot for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_ERP_PREAMBLE) { |
| if (info->use_short_preamble) |
| preamble = WMI_VDEV_PREAMBLE_SHORT; |
| else |
| preamble = WMI_VDEV_PREAMBLE_LONG; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d preamble %dn", |
| arvif->vdev_id, preamble); |
| |
| vdev_param = ar->wmi.vdev_param->preamble; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| preamble); |
| if (ret) |
| ath10k_warn(ar, "failed to set preamble for vdev %d: %i\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_ASSOC) { |
| if (vif->cfg.assoc) { |
| /* Workaround: Make sure monitor vdev is not running |
| * when associating to prevent some firmware revisions |
| * (e.g. 10.1 and 10.2) from crashing. |
| */ |
| if (ar->monitor_started) |
| ath10k_monitor_stop(ar); |
| ath10k_bss_assoc(hw, vif, info); |
| ath10k_monitor_recalc(ar); |
| } else { |
| ath10k_bss_disassoc(hw, vif); |
| } |
| } |
| |
| if (changed & BSS_CHANGED_TXPOWER) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev_id %i txpower %d\n", |
| arvif->vdev_id, info->txpower); |
| |
| arvif->txpower = info->txpower; |
| ret = ath10k_mac_txpower_recalc(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to recalc tx power: %d\n", ret); |
| } |
| |
| if (changed & BSS_CHANGED_PS) { |
| arvif->ps = vif->cfg.ps; |
| |
| ret = ath10k_config_ps(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to setup ps on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_MCAST_RATE && |
| !ath10k_mac_vif_chan(arvif->vif, &def)) { |
| band = def.chan->band; |
| mcast_rate = vif->bss_conf.mcast_rate[band]; |
| if (mcast_rate > 0) |
| rateidx = mcast_rate - 1; |
| else |
| rateidx = ffs(vif->bss_conf.basic_rates) - 1; |
| |
| if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) |
| rateidx += ATH10K_MAC_FIRST_OFDM_RATE_IDX; |
| |
| bitrate = ath10k_wmi_legacy_rates[rateidx].bitrate; |
| hw_value = ath10k_wmi_legacy_rates[rateidx].hw_value; |
| if (ath10k_mac_bitrate_is_cck(bitrate)) |
| preamble = WMI_RATE_PREAMBLE_CCK; |
| else |
| preamble = WMI_RATE_PREAMBLE_OFDM; |
| |
| rate = ATH10K_HW_RATECODE(hw_value, 0, preamble); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac vdev %d mcast_rate %x\n", |
| arvif->vdev_id, rate); |
| |
| vdev_param = ar->wmi.vdev_param->mcast_data_rate; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, |
| vdev_param, rate); |
| if (ret) |
| ath10k_warn(ar, |
| "failed to set mcast rate on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| vdev_param = ar->wmi.vdev_param->bcast_data_rate; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, |
| vdev_param, rate); |
| if (ret) |
| ath10k_warn(ar, |
| "failed to set bcast rate on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (changed & BSS_CHANGED_BASIC_RATES && |
| !ath10k_mac_vif_chan(arvif->vif, &def)) |
| ath10k_recalculate_mgmt_rate(ar, vif, &def); |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static void ath10k_mac_op_set_coverage_class(struct ieee80211_hw *hw, s16 value) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| /* This function should never be called if setting the coverage class |
| * is not supported on this hardware. |
| */ |
| if (!ar->hw_params.hw_ops->set_coverage_class) { |
| WARN_ON_ONCE(1); |
| return; |
| } |
| ar->hw_params.hw_ops->set_coverage_class(ar, value); |
| } |
| |
| struct ath10k_mac_tdls_iter_data { |
| u32 num_tdls_stations; |
| struct ieee80211_vif *curr_vif; |
| }; |
| |
| static void ath10k_mac_tdls_vif_stations_count_iter(void *data, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k_mac_tdls_iter_data *iter_data = data; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ieee80211_vif *sta_vif = arsta->arvif->vif; |
| |
| if (sta->tdls && sta_vif == iter_data->curr_vif) |
| iter_data->num_tdls_stations++; |
| } |
| |
| static int ath10k_mac_tdls_vif_stations_count(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_mac_tdls_iter_data data = {}; |
| |
| data.curr_vif = vif; |
| |
| ieee80211_iterate_stations_atomic(hw, |
| ath10k_mac_tdls_vif_stations_count_iter, |
| &data); |
| return data.num_tdls_stations; |
| } |
| |
| static int ath10k_hw_scan(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_scan_request *hw_req) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct cfg80211_scan_request *req = &hw_req->req; |
| struct wmi_start_scan_arg arg; |
| int ret = 0; |
| int i; |
| u32 scan_timeout; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (ath10k_mac_tdls_vif_stations_count(hw, vif) > 0) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| switch (ar->scan.state) { |
| case ATH10K_SCAN_IDLE: |
| reinit_completion(&ar->scan.started); |
| reinit_completion(&ar->scan.completed); |
| ar->scan.state = ATH10K_SCAN_STARTING; |
| ar->scan.is_roc = false; |
| ar->scan.vdev_id = arvif->vdev_id; |
| ret = 0; |
| break; |
| case ATH10K_SCAN_STARTING: |
| case ATH10K_SCAN_RUNNING: |
| case ATH10K_SCAN_ABORTING: |
| ret = -EBUSY; |
| break; |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (ret) |
| goto exit; |
| |
| memset(&arg, 0, sizeof(arg)); |
| ath10k_wmi_start_scan_init(ar, &arg); |
| arg.vdev_id = arvif->vdev_id; |
| arg.scan_id = ATH10K_SCAN_ID; |
| |
| if (req->ie_len) { |
| arg.ie_len = req->ie_len; |
| memcpy(arg.ie, req->ie, arg.ie_len); |
| } |
| |
| if (req->n_ssids) { |
| arg.n_ssids = req->n_ssids; |
| for (i = 0; i < arg.n_ssids; i++) { |
| arg.ssids[i].len = req->ssids[i].ssid_len; |
| arg.ssids[i].ssid = req->ssids[i].ssid; |
| } |
| } else { |
| arg.scan_ctrl_flags |= WMI_SCAN_FLAG_PASSIVE; |
| } |
| |
| if (req->flags & NL80211_SCAN_FLAG_RANDOM_ADDR) { |
| arg.scan_ctrl_flags |= WMI_SCAN_ADD_SPOOFED_MAC_IN_PROBE_REQ; |
| ether_addr_copy(arg.mac_addr.addr, req->mac_addr); |
| ether_addr_copy(arg.mac_mask.addr, req->mac_addr_mask); |
| } |
| |
| if (req->n_channels) { |
| arg.n_channels = req->n_channels; |
| for (i = 0; i < arg.n_channels; i++) |
| arg.channels[i] = req->channels[i]->center_freq; |
| } |
| |
| /* if duration is set, default dwell times will be overwritten */ |
| if (req->duration) { |
| arg.dwell_time_active = req->duration; |
| arg.dwell_time_passive = req->duration; |
| arg.burst_duration_ms = req->duration; |
| |
| scan_timeout = min_t(u32, arg.max_rest_time * |
| (arg.n_channels - 1) + (req->duration + |
| ATH10K_SCAN_CHANNEL_SWITCH_WMI_EVT_OVERHEAD) * |
| arg.n_channels, arg.max_scan_time); |
| } else { |
| scan_timeout = arg.max_scan_time; |
| } |
| |
| /* Add a 200ms margin to account for event/command processing */ |
| scan_timeout += 200; |
| |
| ret = ath10k_start_scan(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to start hw scan: %d\n", ret); |
| spin_lock_bh(&ar->data_lock); |
| ar->scan.state = ATH10K_SCAN_IDLE; |
| spin_unlock_bh(&ar->data_lock); |
| } |
| |
| ieee80211_queue_delayed_work(ar->hw, &ar->scan.timeout, |
| msecs_to_jiffies(scan_timeout)); |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static void ath10k_cancel_hw_scan(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| mutex_lock(&ar->conf_mutex); |
| ath10k_scan_abort(ar); |
| mutex_unlock(&ar->conf_mutex); |
| |
| cancel_delayed_work_sync(&ar->scan.timeout); |
| } |
| |
| static void ath10k_set_key_h_def_keyidx(struct ath10k *ar, |
| struct ath10k_vif *arvif, |
| enum set_key_cmd cmd, |
| struct ieee80211_key_conf *key) |
| { |
| u32 vdev_param = arvif->ar->wmi.vdev_param->def_keyid; |
| int ret; |
| |
| /* 10.1 firmware branch requires default key index to be set to group |
| * key index after installing it. Otherwise FW/HW Txes corrupted |
| * frames with multi-vif APs. This is not required for main firmware |
| * branch (e.g. 636). |
| * |
| * This is also needed for 636 fw for IBSS-RSN to work more reliably. |
| * |
| * FIXME: It remains unknown if this is required for multi-vif STA |
| * interfaces on 10.1. |
| */ |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_AP && |
| arvif->vdev_type != WMI_VDEV_TYPE_IBSS) |
| return; |
| |
| if (key->cipher == WLAN_CIPHER_SUITE_WEP40) |
| return; |
| |
| if (key->cipher == WLAN_CIPHER_SUITE_WEP104) |
| return; |
| |
| if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) |
| return; |
| |
| if (cmd != SET_KEY) |
| return; |
| |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, |
| key->keyidx); |
| if (ret) |
| ath10k_warn(ar, "failed to set vdev %i group key as default key: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| static int ath10k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, |
| struct ieee80211_vif *vif, struct ieee80211_sta *sta, |
| struct ieee80211_key_conf *key) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_sta *arsta; |
| struct ath10k_peer *peer; |
| const u8 *peer_addr; |
| bool is_wep = key->cipher == WLAN_CIPHER_SUITE_WEP40 || |
| key->cipher == WLAN_CIPHER_SUITE_WEP104; |
| int ret = 0; |
| int ret2; |
| u32 flags = 0; |
| u32 flags2; |
| |
| /* this one needs to be done in software */ |
| if (key->cipher == WLAN_CIPHER_SUITE_AES_CMAC || |
| key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_128 || |
| key->cipher == WLAN_CIPHER_SUITE_BIP_GMAC_256 || |
| key->cipher == WLAN_CIPHER_SUITE_BIP_CMAC_256) |
| return 1; |
| |
| if (arvif->nohwcrypt) |
| return 1; |
| |
| if (key->keyidx > WMI_MAX_KEY_INDEX) |
| return -ENOSPC; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (sta) { |
| arsta = (struct ath10k_sta *)sta->drv_priv; |
| peer_addr = sta->addr; |
| spin_lock_bh(&ar->data_lock); |
| arsta->ucast_cipher = key->cipher; |
| spin_unlock_bh(&ar->data_lock); |
| } else if (arvif->vdev_type == WMI_VDEV_TYPE_STA) { |
| peer_addr = vif->bss_conf.bssid; |
| } else { |
| peer_addr = vif->addr; |
| } |
| |
| key->hw_key_idx = key->keyidx; |
| |
| if (is_wep) { |
| if (cmd == SET_KEY) |
| arvif->wep_keys[key->keyidx] = key; |
| else |
| arvif->wep_keys[key->keyidx] = NULL; |
| } |
| |
| /* the peer should not disappear in mid-way (unless FW goes awry) since |
| * we already hold conf_mutex. we just make sure its there now. |
| */ |
| spin_lock_bh(&ar->data_lock); |
| peer = ath10k_peer_find(ar, arvif->vdev_id, peer_addr); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (!peer) { |
| if (cmd == SET_KEY) { |
| ath10k_warn(ar, "failed to install key for non-existent peer %pM\n", |
| peer_addr); |
| ret = -EOPNOTSUPP; |
| goto exit; |
| } else { |
| /* if the peer doesn't exist there is no key to disable anymore */ |
| goto exit; |
| } |
| } |
| |
| if (key->flags & IEEE80211_KEY_FLAG_PAIRWISE) |
| flags |= WMI_KEY_PAIRWISE; |
| else |
| flags |= WMI_KEY_GROUP; |
| |
| if (is_wep) { |
| if (cmd == DISABLE_KEY) |
| ath10k_clear_vdev_key(arvif, key); |
| |
| /* When WEP keys are uploaded it's possible that there are |
| * stations associated already (e.g. when merging) without any |
| * keys. Static WEP needs an explicit per-peer key upload. |
| */ |
| if (vif->type == NL80211_IFTYPE_ADHOC && |
| cmd == SET_KEY) |
| ath10k_mac_vif_update_wep_key(arvif, key); |
| |
| /* 802.1x never sets the def_wep_key_idx so each set_key() |
| * call changes default tx key. |
| * |
| * Static WEP sets def_wep_key_idx via .set_default_unicast_key |
| * after first set_key(). |
| */ |
| if (cmd == SET_KEY && arvif->def_wep_key_idx == -1) |
| flags |= WMI_KEY_TX_USAGE; |
| } |
| |
| ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags); |
| if (ret) { |
| WARN_ON(ret > 0); |
| ath10k_warn(ar, "failed to install key for vdev %i peer %pM: %d\n", |
| arvif->vdev_id, peer_addr, ret); |
| goto exit; |
| } |
| |
| /* mac80211 sets static WEP keys as groupwise while firmware requires |
| * them to be installed twice as both pairwise and groupwise. |
| */ |
| if (is_wep && !sta && vif->type == NL80211_IFTYPE_STATION) { |
| flags2 = flags; |
| flags2 &= ~WMI_KEY_GROUP; |
| flags2 |= WMI_KEY_PAIRWISE; |
| |
| ret = ath10k_install_key(arvif, key, cmd, peer_addr, flags2); |
| if (ret) { |
| WARN_ON(ret > 0); |
| ath10k_warn(ar, "failed to install (ucast) key for vdev %i peer %pM: %d\n", |
| arvif->vdev_id, peer_addr, ret); |
| ret2 = ath10k_install_key(arvif, key, DISABLE_KEY, |
| peer_addr, flags); |
| if (ret2) { |
| WARN_ON(ret2 > 0); |
| ath10k_warn(ar, "failed to disable (mcast) key for vdev %i peer %pM: %d\n", |
| arvif->vdev_id, peer_addr, ret2); |
| } |
| goto exit; |
| } |
| } |
| |
| ath10k_set_key_h_def_keyidx(ar, arvif, cmd, key); |
| |
| spin_lock_bh(&ar->data_lock); |
| peer = ath10k_peer_find(ar, arvif->vdev_id, peer_addr); |
| if (peer && cmd == SET_KEY) |
| peer->keys[key->keyidx] = key; |
| else if (peer && cmd == DISABLE_KEY) |
| peer->keys[key->keyidx] = NULL; |
| else if (peer == NULL) |
| /* impossible unless FW goes crazy */ |
| ath10k_warn(ar, "Peer %pM disappeared!\n", peer_addr); |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (sta && sta->tdls) |
| ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->authorize, 1); |
| else if (sta && cmd == SET_KEY && (key->flags & IEEE80211_KEY_FLAG_PAIRWISE)) |
| ath10k_wmi_peer_set_param(ar, arvif->vdev_id, peer_addr, |
| ar->wmi.peer_param->authorize, 1); |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static void ath10k_set_default_unicast_key(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| int keyidx) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret; |
| |
| mutex_lock(&arvif->ar->conf_mutex); |
| |
| if (arvif->ar->state != ATH10K_STATE_ON) |
| goto unlock; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d set keyidx %d\n", |
| arvif->vdev_id, keyidx); |
| |
| ret = ath10k_wmi_vdev_set_param(arvif->ar, |
| arvif->vdev_id, |
| arvif->ar->wmi.vdev_param->def_keyid, |
| keyidx); |
| |
| if (ret) { |
| ath10k_warn(ar, "failed to update wep key index for vdev %d: %d\n", |
| arvif->vdev_id, |
| ret); |
| goto unlock; |
| } |
| |
| arvif->def_wep_key_idx = keyidx; |
| |
| unlock: |
| mutex_unlock(&arvif->ar->conf_mutex); |
| } |
| |
| static void ath10k_sta_rc_update_wk(struct work_struct *wk) |
| { |
| struct ath10k *ar; |
| struct ath10k_vif *arvif; |
| struct ath10k_sta *arsta; |
| struct ieee80211_sta *sta; |
| struct cfg80211_chan_def def; |
| enum nl80211_band band; |
| const u8 *ht_mcs_mask; |
| const u16 *vht_mcs_mask; |
| u32 changed, bw, nss, smps; |
| int err; |
| |
| arsta = container_of(wk, struct ath10k_sta, update_wk); |
| sta = container_of((void *)arsta, struct ieee80211_sta, drv_priv); |
| arvif = arsta->arvif; |
| ar = arvif->ar; |
| |
| if (WARN_ON(ath10k_mac_vif_chan(arvif->vif, &def))) |
| return; |
| |
| band = def.chan->band; |
| ht_mcs_mask = arvif->bitrate_mask.control[band].ht_mcs; |
| vht_mcs_mask = arvif->bitrate_mask.control[band].vht_mcs; |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| changed = arsta->changed; |
| arsta->changed = 0; |
| |
| bw = arsta->bw; |
| nss = arsta->nss; |
| smps = arsta->smps; |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| nss = max_t(u32, 1, nss); |
| nss = min(nss, max(ath10k_mac_max_ht_nss(ht_mcs_mask), |
| ath10k_mac_max_vht_nss(vht_mcs_mask))); |
| |
| if (changed & IEEE80211_RC_BW_CHANGED) { |
| enum wmi_phy_mode mode; |
| |
| mode = chan_to_phymode(&def); |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac update sta %pM peer bw %d phymode %d\n", |
| sta->addr, bw, mode); |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->phymode, mode); |
| if (err) { |
| ath10k_warn(ar, "failed to update STA %pM peer phymode %d: %d\n", |
| sta->addr, mode, err); |
| goto exit; |
| } |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->chan_width, bw); |
| if (err) |
| ath10k_warn(ar, "failed to update STA %pM peer bw %d: %d\n", |
| sta->addr, bw, err); |
| } |
| |
| if (changed & IEEE80211_RC_NSS_CHANGED) { |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac update sta %pM nss %d\n", |
| sta->addr, nss); |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->nss, nss); |
| if (err) |
| ath10k_warn(ar, "failed to update STA %pM nss %d: %d\n", |
| sta->addr, nss, err); |
| } |
| |
| if (changed & IEEE80211_RC_SMPS_CHANGED) { |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac update sta %pM smps %d\n", |
| sta->addr, smps); |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->smps_state, smps); |
| if (err) |
| ath10k_warn(ar, "failed to update STA %pM smps %d: %d\n", |
| sta->addr, smps, err); |
| } |
| |
| if (changed & IEEE80211_RC_SUPP_RATES_CHANGED) { |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac update sta %pM supp rates\n", |
| sta->addr); |
| |
| err = ath10k_station_assoc(ar, arvif->vif, sta, true); |
| if (err) |
| ath10k_warn(ar, "failed to reassociate station: %pM\n", |
| sta->addr); |
| } |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static int ath10k_mac_inc_num_stations(struct ath10k_vif *arvif, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_STA && !sta->tdls) |
| return 0; |
| |
| if (ar->num_stations >= ar->max_num_stations) |
| return -ENOBUFS; |
| |
| ar->num_stations++; |
| |
| return 0; |
| } |
| |
| static void ath10k_mac_dec_num_stations(struct ath10k_vif *arvif, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k *ar = arvif->ar; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (arvif->vdev_type == WMI_VDEV_TYPE_STA && !sta->tdls) |
| return; |
| |
| ar->num_stations--; |
| } |
| |
| static int ath10k_sta_set_txpwr(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret = 0; |
| s16 txpwr; |
| |
| if (sta->deflink.txpwr.type == NL80211_TX_POWER_AUTOMATIC) { |
| txpwr = 0; |
| } else { |
| txpwr = sta->deflink.txpwr.power; |
| if (!txpwr) |
| return -EINVAL; |
| } |
| |
| if (txpwr > ATH10K_TX_POWER_MAX_VAL || txpwr < ATH10K_TX_POWER_MIN_VAL) |
| return -EINVAL; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ret = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| ar->wmi.peer_param->use_fixed_power, txpwr); |
| if (ret) { |
| ath10k_warn(ar, "failed to set tx power for station ret: %d\n", |
| ret); |
| goto out; |
| } |
| |
| out: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| struct ath10k_mac_iter_tid_conf_data { |
| struct ieee80211_vif *curr_vif; |
| struct ath10k *ar; |
| bool reset_config; |
| }; |
| |
| static bool |
| ath10k_mac_bitrate_mask_has_single_rate(struct ath10k *ar, |
| enum nl80211_band band, |
| const struct cfg80211_bitrate_mask *mask, |
| int *vht_num_rates) |
| { |
| int num_rates = 0; |
| int i, tmp; |
| |
| num_rates += hweight32(mask->control[band].legacy); |
| |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].ht_mcs); i++) |
| num_rates += hweight8(mask->control[band].ht_mcs[i]); |
| |
| *vht_num_rates = 0; |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].vht_mcs); i++) { |
| tmp = hweight16(mask->control[band].vht_mcs[i]); |
| num_rates += tmp; |
| *vht_num_rates += tmp; |
| } |
| |
| return num_rates == 1; |
| } |
| |
| static int |
| ath10k_mac_bitrate_mask_get_single_rate(struct ath10k *ar, |
| enum nl80211_band band, |
| const struct cfg80211_bitrate_mask *mask, |
| u8 *rate, u8 *nss, bool vht_only) |
| { |
| int rate_idx; |
| int i; |
| u16 bitrate; |
| u8 preamble; |
| u8 hw_rate; |
| |
| if (vht_only) |
| goto next; |
| |
| if (hweight32(mask->control[band].legacy) == 1) { |
| rate_idx = ffs(mask->control[band].legacy) - 1; |
| |
| if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) |
| rate_idx += ATH10K_MAC_FIRST_OFDM_RATE_IDX; |
| |
| hw_rate = ath10k_wmi_legacy_rates[rate_idx].hw_value; |
| bitrate = ath10k_wmi_legacy_rates[rate_idx].bitrate; |
| |
| if (ath10k_mac_bitrate_is_cck(bitrate)) |
| preamble = WMI_RATE_PREAMBLE_CCK; |
| else |
| preamble = WMI_RATE_PREAMBLE_OFDM; |
| |
| *nss = 1; |
| *rate = preamble << 6 | |
| (*nss - 1) << 4 | |
| hw_rate << 0; |
| |
| return 0; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].ht_mcs); i++) { |
| if (hweight8(mask->control[band].ht_mcs[i]) == 1) { |
| *nss = i + 1; |
| *rate = WMI_RATE_PREAMBLE_HT << 6 | |
| (*nss - 1) << 4 | |
| (ffs(mask->control[band].ht_mcs[i]) - 1); |
| |
| return 0; |
| } |
| } |
| |
| next: |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].vht_mcs); i++) { |
| if (hweight16(mask->control[band].vht_mcs[i]) == 1) { |
| *nss = i + 1; |
| *rate = WMI_RATE_PREAMBLE_VHT << 6 | |
| (*nss - 1) << 4 | |
| (ffs(mask->control[band].vht_mcs[i]) - 1); |
| |
| return 0; |
| } |
| } |
| |
| return -EINVAL; |
| } |
| |
| static int ath10k_mac_validate_rate_mask(struct ath10k *ar, |
| struct ieee80211_sta *sta, |
| u32 rate_ctrl_flag, u8 nss) |
| { |
| struct ieee80211_sta_ht_cap *ht_cap = &sta->deflink.ht_cap; |
| struct ieee80211_sta_vht_cap *vht_cap = &sta->deflink.vht_cap; |
| |
| if (nss > sta->deflink.rx_nss) { |
| ath10k_warn(ar, "Invalid nss field, configured %u limit %u\n", |
| nss, sta->deflink.rx_nss); |
| return -EINVAL; |
| } |
| |
| if (ATH10K_HW_PREAMBLE(rate_ctrl_flag) == WMI_RATE_PREAMBLE_VHT) { |
| if (!vht_cap->vht_supported) { |
| ath10k_warn(ar, "Invalid VHT rate for sta %pM\n", |
| sta->addr); |
| return -EINVAL; |
| } |
| } else if (ATH10K_HW_PREAMBLE(rate_ctrl_flag) == WMI_RATE_PREAMBLE_HT) { |
| if (!ht_cap->ht_supported || vht_cap->vht_supported) { |
| ath10k_warn(ar, "Invalid HT rate for sta %pM\n", |
| sta->addr); |
| return -EINVAL; |
| } |
| } else { |
| if (ht_cap->ht_supported || vht_cap->vht_supported) |
| return -EINVAL; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| ath10k_mac_tid_bitrate_config(struct ath10k *ar, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| u32 *rate_ctrl_flag, u8 *rate_ctrl, |
| enum nl80211_tx_rate_setting txrate_type, |
| const struct cfg80211_bitrate_mask *mask) |
| { |
| struct cfg80211_chan_def def; |
| enum nl80211_band band; |
| u8 nss, rate; |
| int vht_num_rates, ret; |
| |
| if (WARN_ON(ath10k_mac_vif_chan(vif, &def))) |
| return -EINVAL; |
| |
| if (txrate_type == NL80211_TX_RATE_AUTOMATIC) { |
| *rate_ctrl = WMI_TID_CONFIG_RATE_CONTROL_AUTO; |
| *rate_ctrl_flag = 0; |
| return 0; |
| } |
| |
| band = def.chan->band; |
| |
| if (!ath10k_mac_bitrate_mask_has_single_rate(ar, band, mask, |
| &vht_num_rates)) { |
| return -EINVAL; |
| } |
| |
| ret = ath10k_mac_bitrate_mask_get_single_rate(ar, band, mask, |
| &rate, &nss, false); |
| if (ret) { |
| ath10k_warn(ar, "failed to get single rate: %d\n", |
| ret); |
| return ret; |
| } |
| |
| *rate_ctrl_flag = rate; |
| |
| if (sta && ath10k_mac_validate_rate_mask(ar, sta, *rate_ctrl_flag, nss)) |
| return -EINVAL; |
| |
| if (txrate_type == NL80211_TX_RATE_FIXED) |
| *rate_ctrl = WMI_TID_CONFIG_RATE_CONTROL_FIXED_RATE; |
| else if (txrate_type == NL80211_TX_RATE_LIMITED && |
| (test_bit(WMI_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT, |
| ar->wmi.svc_map))) |
| *rate_ctrl = WMI_PEER_TID_CONFIG_RATE_UPPER_CAP; |
| else |
| return -EOPNOTSUPP; |
| |
| return 0; |
| } |
| |
| static int ath10k_mac_set_tid_config(struct ath10k *ar, struct ieee80211_sta *sta, |
| struct ieee80211_vif *vif, u32 changed, |
| struct wmi_per_peer_per_tid_cfg_arg *arg) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_sta *arsta; |
| int ret; |
| |
| if (sta) { |
| if (!sta->wme) |
| return -EOPNOTSUPP; |
| |
| arsta = (struct ath10k_sta *)sta->drv_priv; |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_NOACK)) { |
| if ((arsta->retry_long[arg->tid] > 0 || |
| arsta->rate_code[arg->tid] > 0 || |
| arsta->ampdu[arg->tid] == |
| WMI_TID_CONFIG_AGGR_CONTROL_ENABLE) && |
| arg->ack_policy == WMI_PEER_TID_CONFIG_NOACK) { |
| changed &= ~BIT(NL80211_TID_CONFIG_ATTR_NOACK); |
| arg->ack_policy = 0; |
| arg->aggr_control = 0; |
| arg->rate_ctrl = 0; |
| arg->rcode_flags = 0; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL)) { |
| if (arsta->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK || |
| arvif->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK) { |
| arg->aggr_control = 0; |
| changed &= ~BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG); |
| } |
| } |
| |
| if (changed & (BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE))) { |
| if (arsta->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK || |
| arvif->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK) { |
| arg->rate_ctrl = 0; |
| arg->rcode_flags = 0; |
| } |
| } |
| |
| ether_addr_copy(arg->peer_macaddr.addr, sta->addr); |
| |
| ret = ath10k_wmi_set_per_peer_per_tid_cfg(ar, arg); |
| if (ret) |
| return ret; |
| |
| /* Store the configured parameters in success case */ |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_NOACK)) { |
| arsta->noack[arg->tid] = arg->ack_policy; |
| arg->ack_policy = 0; |
| arg->aggr_control = 0; |
| arg->rate_ctrl = 0; |
| arg->rcode_flags = 0; |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG)) { |
| arsta->retry_long[arg->tid] = arg->retry_count; |
| arg->retry_count = 0; |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL)) { |
| arsta->ampdu[arg->tid] = arg->aggr_control; |
| arg->aggr_control = 0; |
| } |
| |
| if (changed & (BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE))) { |
| arsta->rate_ctrl[arg->tid] = arg->rate_ctrl; |
| arg->rate_ctrl = 0; |
| arg->rcode_flags = 0; |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL)) { |
| arsta->rtscts[arg->tid] = arg->rtscts_ctrl; |
| arg->ext_tid_cfg_bitmap = 0; |
| } |
| } else { |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_NOACK)) { |
| if ((arvif->retry_long[arg->tid] || |
| arvif->rate_code[arg->tid] || |
| arvif->ampdu[arg->tid] == |
| WMI_TID_CONFIG_AGGR_CONTROL_ENABLE) && |
| arg->ack_policy == WMI_PEER_TID_CONFIG_NOACK) { |
| changed &= ~BIT(NL80211_TID_CONFIG_ATTR_NOACK); |
| } else { |
| arvif->noack[arg->tid] = arg->ack_policy; |
| arvif->ampdu[arg->tid] = arg->aggr_control; |
| arvif->rate_ctrl[arg->tid] = arg->rate_ctrl; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG)) { |
| if (arvif->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK) |
| changed &= ~BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG); |
| else |
| arvif->retry_long[arg->tid] = arg->retry_count; |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL)) { |
| if (arvif->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK) |
| changed &= ~BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL); |
| else |
| arvif->ampdu[arg->tid] = arg->aggr_control; |
| } |
| |
| if (changed & (BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE))) { |
| if (arvif->noack[arg->tid] == WMI_PEER_TID_CONFIG_NOACK) { |
| changed &= ~(BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE)); |
| } else { |
| arvif->rate_ctrl[arg->tid] = arg->rate_ctrl; |
| arvif->rate_code[arg->tid] = arg->rcode_flags; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL)) { |
| arvif->rtscts[arg->tid] = arg->rtscts_ctrl; |
| arg->ext_tid_cfg_bitmap = 0; |
| } |
| |
| if (changed) |
| arvif->tid_conf_changed[arg->tid] |= changed; |
| } |
| |
| return 0; |
| } |
| |
| static int |
| ath10k_mac_parse_tid_config(struct ath10k *ar, |
| struct ieee80211_sta *sta, |
| struct ieee80211_vif *vif, |
| struct cfg80211_tid_cfg *tid_conf, |
| struct wmi_per_peer_per_tid_cfg_arg *arg) |
| { |
| u32 changed = tid_conf->mask; |
| int ret = 0, i = 0; |
| |
| if (!changed) |
| return -EINVAL; |
| |
| while (i < ATH10K_TID_MAX) { |
| if (!(tid_conf->tids & BIT(i))) { |
| i++; |
| continue; |
| } |
| |
| arg->tid = i; |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_NOACK)) { |
| if (tid_conf->noack == NL80211_TID_CONFIG_ENABLE) { |
| arg->ack_policy = WMI_PEER_TID_CONFIG_NOACK; |
| arg->rate_ctrl = |
| WMI_TID_CONFIG_RATE_CONTROL_DEFAULT_LOWEST_RATE; |
| arg->aggr_control = |
| WMI_TID_CONFIG_AGGR_CONTROL_DISABLE; |
| } else { |
| arg->ack_policy = |
| WMI_PEER_TID_CONFIG_ACK; |
| arg->rate_ctrl = |
| WMI_TID_CONFIG_RATE_CONTROL_AUTO; |
| arg->aggr_control = |
| WMI_TID_CONFIG_AGGR_CONTROL_ENABLE; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG)) |
| arg->retry_count = tid_conf->retry_long; |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL)) { |
| if (tid_conf->noack == NL80211_TID_CONFIG_ENABLE) |
| arg->aggr_control = WMI_TID_CONFIG_AGGR_CONTROL_ENABLE; |
| else |
| arg->aggr_control = WMI_TID_CONFIG_AGGR_CONTROL_DISABLE; |
| } |
| |
| if (changed & (BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE))) { |
| ret = ath10k_mac_tid_bitrate_config(ar, vif, sta, |
| &arg->rcode_flags, |
| &arg->rate_ctrl, |
| tid_conf->txrate_type, |
| &tid_conf->txrate_mask); |
| if (ret) { |
| ath10k_warn(ar, "failed to configure bitrate mask %d\n", |
| ret); |
| arg->rcode_flags = 0; |
| arg->rate_ctrl = 0; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL)) { |
| if (tid_conf->rtscts) |
| arg->rtscts_ctrl = tid_conf->rtscts; |
| |
| arg->ext_tid_cfg_bitmap = WMI_EXT_TID_RTS_CTS_CONFIG; |
| } |
| |
| ret = ath10k_mac_set_tid_config(ar, sta, vif, changed, arg); |
| if (ret) |
| return ret; |
| i++; |
| } |
| |
| return ret; |
| } |
| |
| static int ath10k_mac_reset_tid_config(struct ath10k *ar, |
| struct ieee80211_sta *sta, |
| struct ath10k_vif *arvif, |
| u8 tids) |
| { |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct wmi_per_peer_per_tid_cfg_arg arg; |
| int ret = 0, i = 0; |
| |
| arg.vdev_id = arvif->vdev_id; |
| while (i < ATH10K_TID_MAX) { |
| if (!(tids & BIT(i))) { |
| i++; |
| continue; |
| } |
| |
| arg.tid = i; |
| arg.ack_policy = WMI_PEER_TID_CONFIG_ACK; |
| arg.retry_count = ATH10K_MAX_RETRY_COUNT; |
| arg.rate_ctrl = WMI_TID_CONFIG_RATE_CONTROL_AUTO; |
| arg.aggr_control = WMI_TID_CONFIG_AGGR_CONTROL_ENABLE; |
| arg.rtscts_ctrl = WMI_TID_CONFIG_RTSCTS_CONTROL_ENABLE; |
| arg.ext_tid_cfg_bitmap = WMI_EXT_TID_RTS_CTS_CONFIG; |
| |
| ether_addr_copy(arg.peer_macaddr.addr, sta->addr); |
| |
| ret = ath10k_wmi_set_per_peer_per_tid_cfg(ar, &arg); |
| if (ret) |
| return ret; |
| |
| if (!arvif->tids_rst) { |
| arsta->retry_long[i] = -1; |
| arsta->noack[i] = -1; |
| arsta->ampdu[i] = -1; |
| arsta->rate_code[i] = -1; |
| arsta->rate_ctrl[i] = 0; |
| arsta->rtscts[i] = -1; |
| } else { |
| arvif->retry_long[i] = 0; |
| arvif->noack[i] = 0; |
| arvif->ampdu[i] = 0; |
| arvif->rate_code[i] = 0; |
| arvif->rate_ctrl[i] = 0; |
| arvif->rtscts[i] = 0; |
| } |
| |
| i++; |
| } |
| |
| return ret; |
| } |
| |
| static void ath10k_sta_tid_cfg_wk(struct work_struct *wk) |
| { |
| struct wmi_per_peer_per_tid_cfg_arg arg = {}; |
| struct ieee80211_sta *sta; |
| struct ath10k_sta *arsta; |
| struct ath10k_vif *arvif; |
| struct ath10k *ar; |
| bool config_apply; |
| int ret, i; |
| u32 changed; |
| u8 nss; |
| |
| arsta = container_of(wk, struct ath10k_sta, tid_config_wk); |
| sta = container_of((void *)arsta, struct ieee80211_sta, drv_priv); |
| arvif = arsta->arvif; |
| ar = arvif->ar; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (arvif->tids_rst) { |
| ret = ath10k_mac_reset_tid_config(ar, sta, arvif, |
| arvif->tids_rst); |
| goto exit; |
| } |
| |
| ether_addr_copy(arg.peer_macaddr.addr, sta->addr); |
| |
| for (i = 0; i < ATH10K_TID_MAX; i++) { |
| config_apply = false; |
| changed = arvif->tid_conf_changed[i]; |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_NOACK)) { |
| if (arsta->noack[i] != -1) { |
| arg.ack_policy = 0; |
| } else { |
| config_apply = true; |
| arg.ack_policy = arvif->noack[i]; |
| arg.aggr_control = arvif->ampdu[i]; |
| arg.rate_ctrl = arvif->rate_ctrl[i]; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG)) { |
| if (arsta->retry_long[i] != -1 || |
| arsta->noack[i] == WMI_PEER_TID_CONFIG_NOACK || |
| arvif->noack[i] == WMI_PEER_TID_CONFIG_NOACK) { |
| arg.retry_count = 0; |
| } else { |
| arg.retry_count = arvif->retry_long[i]; |
| config_apply = true; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL)) { |
| if (arsta->ampdu[i] != -1 || |
| arsta->noack[i] == WMI_PEER_TID_CONFIG_NOACK || |
| arvif->noack[i] == WMI_PEER_TID_CONFIG_NOACK) { |
| arg.aggr_control = 0; |
| } else { |
| arg.aggr_control = arvif->ampdu[i]; |
| config_apply = true; |
| } |
| } |
| |
| if (changed & (BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE))) { |
| nss = ATH10K_HW_NSS(arvif->rate_code[i]); |
| ret = ath10k_mac_validate_rate_mask(ar, sta, |
| arvif->rate_code[i], |
| nss); |
| if (ret && |
| arvif->rate_ctrl[i] > WMI_TID_CONFIG_RATE_CONTROL_AUTO) { |
| arg.rate_ctrl = 0; |
| arg.rcode_flags = 0; |
| } |
| |
| if (arsta->rate_ctrl[i] > |
| WMI_TID_CONFIG_RATE_CONTROL_AUTO || |
| arsta->noack[i] == WMI_PEER_TID_CONFIG_NOACK || |
| arvif->noack[i] == WMI_PEER_TID_CONFIG_NOACK) { |
| arg.rate_ctrl = 0; |
| arg.rcode_flags = 0; |
| } else { |
| arg.rate_ctrl = arvif->rate_ctrl[i]; |
| arg.rcode_flags = arvif->rate_code[i]; |
| config_apply = true; |
| } |
| } |
| |
| if (changed & BIT(NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL)) { |
| if (arsta->rtscts[i]) { |
| arg.rtscts_ctrl = 0; |
| arg.ext_tid_cfg_bitmap = 0; |
| } else { |
| arg.rtscts_ctrl = arvif->rtscts[i] - 1; |
| arg.ext_tid_cfg_bitmap = |
| WMI_EXT_TID_RTS_CTS_CONFIG; |
| config_apply = true; |
| } |
| } |
| |
| arg.tid = i; |
| |
| if (config_apply) { |
| ret = ath10k_wmi_set_per_peer_per_tid_cfg(ar, &arg); |
| if (ret) |
| ath10k_warn(ar, "failed to set per tid config for sta %pM: %d\n", |
| sta->addr, ret); |
| } |
| |
| arg.ack_policy = 0; |
| arg.retry_count = 0; |
| arg.aggr_control = 0; |
| arg.rate_ctrl = 0; |
| arg.rcode_flags = 0; |
| } |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static void ath10k_mac_vif_stations_tid_conf(void *data, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k_mac_iter_tid_conf_data *iter_data = data; |
| struct ieee80211_vif *sta_vif = arsta->arvif->vif; |
| |
| if (sta_vif != iter_data->curr_vif || !sta->wme) |
| return; |
| |
| ieee80211_queue_work(iter_data->ar->hw, &arsta->tid_config_wk); |
| } |
| |
| static int ath10k_sta_state(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| enum ieee80211_sta_state old_state, |
| enum ieee80211_sta_state new_state) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k_peer *peer; |
| int ret = 0; |
| int i; |
| |
| if (old_state == IEEE80211_STA_NOTEXIST && |
| new_state == IEEE80211_STA_NONE) { |
| memset(arsta, 0, sizeof(*arsta)); |
| arsta->arvif = arvif; |
| arsta->peer_ps_state = WMI_PEER_PS_STATE_DISABLED; |
| INIT_WORK(&arsta->update_wk, ath10k_sta_rc_update_wk); |
| INIT_WORK(&arsta->tid_config_wk, ath10k_sta_tid_cfg_wk); |
| |
| for (i = 0; i < ARRAY_SIZE(sta->txq); i++) |
| ath10k_mac_txq_init(sta->txq[i]); |
| } |
| |
| /* cancel must be done outside the mutex to avoid deadlock */ |
| if ((old_state == IEEE80211_STA_NONE && |
| new_state == IEEE80211_STA_NOTEXIST)) { |
| cancel_work_sync(&arsta->update_wk); |
| cancel_work_sync(&arsta->tid_config_wk); |
| } |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (old_state == IEEE80211_STA_NOTEXIST && |
| new_state == IEEE80211_STA_NONE) { |
| /* |
| * New station addition. |
| */ |
| enum wmi_peer_type peer_type = WMI_PEER_TYPE_DEFAULT; |
| u32 num_tdls_stations; |
| |
| ath10k_dbg(ar, ATH10K_DBG_STA, |
| "mac vdev %d peer create %pM (new sta) sta %d / %d peer %d / %d\n", |
| arvif->vdev_id, sta->addr, |
| ar->num_stations + 1, ar->max_num_stations, |
| ar->num_peers + 1, ar->max_num_peers); |
| |
| num_tdls_stations = ath10k_mac_tdls_vif_stations_count(hw, vif); |
| |
| if (sta->tdls) { |
| if (num_tdls_stations >= ar->max_num_tdls_vdevs) { |
| ath10k_warn(ar, "vdev %i exceeded maximum number of tdls vdevs %i\n", |
| arvif->vdev_id, |
| ar->max_num_tdls_vdevs); |
| ret = -ELNRNG; |
| goto exit; |
| } |
| peer_type = WMI_PEER_TYPE_TDLS; |
| } |
| |
| ret = ath10k_mac_inc_num_stations(arvif, sta); |
| if (ret) { |
| ath10k_warn(ar, "refusing to associate station: too many connected already (%d)\n", |
| ar->max_num_stations); |
| goto exit; |
| } |
| |
| if (ath10k_debug_is_extd_tx_stats_enabled(ar)) { |
| arsta->tx_stats = kzalloc(sizeof(*arsta->tx_stats), |
| GFP_KERNEL); |
| if (!arsta->tx_stats) { |
| ath10k_mac_dec_num_stations(arvif, sta); |
| ret = -ENOMEM; |
| goto exit; |
| } |
| } |
| |
| ret = ath10k_peer_create(ar, vif, sta, arvif->vdev_id, |
| sta->addr, peer_type); |
| if (ret) { |
| ath10k_warn(ar, "failed to add peer %pM for vdev %d when adding a new sta: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| ath10k_mac_dec_num_stations(arvif, sta); |
| kfree(arsta->tx_stats); |
| goto exit; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| peer = ath10k_peer_find(ar, arvif->vdev_id, sta->addr); |
| if (!peer) { |
| ath10k_warn(ar, "failed to lookup peer %pM on vdev %i\n", |
| vif->addr, arvif->vdev_id); |
| spin_unlock_bh(&ar->data_lock); |
| ath10k_peer_delete(ar, arvif->vdev_id, sta->addr); |
| ath10k_mac_dec_num_stations(arvif, sta); |
| kfree(arsta->tx_stats); |
| ret = -ENOENT; |
| goto exit; |
| } |
| |
| arsta->peer_id = find_first_bit(peer->peer_ids, |
| ATH10K_MAX_NUM_PEER_IDS); |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (!sta->tdls) |
| goto exit; |
| |
| ret = ath10k_wmi_update_fw_tdls_state(ar, arvif->vdev_id, |
| WMI_TDLS_ENABLE_ACTIVE); |
| if (ret) { |
| ath10k_warn(ar, "failed to update fw tdls state on vdev %i: %i\n", |
| arvif->vdev_id, ret); |
| ath10k_peer_delete(ar, arvif->vdev_id, |
| sta->addr); |
| ath10k_mac_dec_num_stations(arvif, sta); |
| kfree(arsta->tx_stats); |
| goto exit; |
| } |
| |
| ret = ath10k_mac_tdls_peer_update(ar, arvif->vdev_id, sta, |
| WMI_TDLS_PEER_STATE_PEERING); |
| if (ret) { |
| ath10k_warn(ar, |
| "failed to update tdls peer %pM for vdev %d when adding a new sta: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| ath10k_peer_delete(ar, arvif->vdev_id, sta->addr); |
| ath10k_mac_dec_num_stations(arvif, sta); |
| kfree(arsta->tx_stats); |
| |
| if (num_tdls_stations != 0) |
| goto exit; |
| ath10k_wmi_update_fw_tdls_state(ar, arvif->vdev_id, |
| WMI_TDLS_DISABLE); |
| } |
| } else if ((old_state == IEEE80211_STA_NONE && |
| new_state == IEEE80211_STA_NOTEXIST)) { |
| /* |
| * Existing station deletion. |
| */ |
| ath10k_dbg(ar, ATH10K_DBG_STA, |
| "mac vdev %d peer delete %pM sta %pK (sta gone)\n", |
| arvif->vdev_id, sta->addr, sta); |
| |
| if (sta->tdls) { |
| ret = ath10k_mac_tdls_peer_update(ar, arvif->vdev_id, |
| sta, |
| WMI_TDLS_PEER_STATE_TEARDOWN); |
| if (ret) |
| ath10k_warn(ar, "failed to update tdls peer state for %pM state %d: %i\n", |
| sta->addr, |
| WMI_TDLS_PEER_STATE_TEARDOWN, ret); |
| } |
| |
| ret = ath10k_peer_delete(ar, arvif->vdev_id, sta->addr); |
| if (ret) |
| ath10k_warn(ar, "failed to delete peer %pM for vdev %d: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| |
| ath10k_mac_dec_num_stations(arvif, sta); |
| |
| spin_lock_bh(&ar->data_lock); |
| for (i = 0; i < ARRAY_SIZE(ar->peer_map); i++) { |
| peer = ar->peer_map[i]; |
| if (!peer) |
| continue; |
| |
| if (peer->sta == sta) { |
| ath10k_warn(ar, "found sta peer %pM (ptr %pK id %d) entry on vdev %i after it was supposedly removed\n", |
| sta->addr, peer, i, arvif->vdev_id); |
| peer->sta = NULL; |
| |
| /* Clean up the peer object as well since we |
| * must have failed to do this above. |
| */ |
| ath10k_peer_map_cleanup(ar, peer); |
| } |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (ath10k_debug_is_extd_tx_stats_enabled(ar)) { |
| kfree(arsta->tx_stats); |
| arsta->tx_stats = NULL; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(sta->txq); i++) |
| ath10k_mac_txq_unref(ar, sta->txq[i]); |
| |
| if (!sta->tdls) |
| goto exit; |
| |
| if (ath10k_mac_tdls_vif_stations_count(hw, vif)) |
| goto exit; |
| |
| /* This was the last tdls peer in current vif */ |
| ret = ath10k_wmi_update_fw_tdls_state(ar, arvif->vdev_id, |
| WMI_TDLS_DISABLE); |
| if (ret) { |
| ath10k_warn(ar, "failed to update fw tdls state on vdev %i: %i\n", |
| arvif->vdev_id, ret); |
| } |
| } else if (old_state == IEEE80211_STA_AUTH && |
| new_state == IEEE80211_STA_ASSOC && |
| (vif->type == NL80211_IFTYPE_AP || |
| vif->type == NL80211_IFTYPE_MESH_POINT || |
| vif->type == NL80211_IFTYPE_ADHOC)) { |
| /* |
| * New association. |
| */ |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac sta %pM associated\n", |
| sta->addr); |
| |
| ret = ath10k_station_assoc(ar, vif, sta, false); |
| if (ret) |
| ath10k_warn(ar, "failed to associate station %pM for vdev %i: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| } else if (old_state == IEEE80211_STA_ASSOC && |
| new_state == IEEE80211_STA_AUTHORIZED && |
| sta->tdls) { |
| /* |
| * Tdls station authorized. |
| */ |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac tdls sta %pM authorized\n", |
| sta->addr); |
| |
| ret = ath10k_station_assoc(ar, vif, sta, false); |
| if (ret) { |
| ath10k_warn(ar, "failed to associate tdls station %pM for vdev %i: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| goto exit; |
| } |
| |
| ret = ath10k_mac_tdls_peer_update(ar, arvif->vdev_id, sta, |
| WMI_TDLS_PEER_STATE_CONNECTED); |
| if (ret) |
| ath10k_warn(ar, "failed to update tdls peer %pM for vdev %i: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| } else if (old_state == IEEE80211_STA_ASSOC && |
| new_state == IEEE80211_STA_AUTH && |
| (vif->type == NL80211_IFTYPE_AP || |
| vif->type == NL80211_IFTYPE_MESH_POINT || |
| vif->type == NL80211_IFTYPE_ADHOC)) { |
| /* |
| * Disassociation. |
| */ |
| ath10k_dbg(ar, ATH10K_DBG_STA, "mac sta %pM disassociated\n", |
| sta->addr); |
| |
| ret = ath10k_station_disassoc(ar, vif, sta); |
| if (ret) |
| ath10k_warn(ar, "failed to disassociate station: %pM vdev %i: %i\n", |
| sta->addr, arvif->vdev_id, ret); |
| } |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static int ath10k_conf_tx_uapsd(struct ath10k *ar, struct ieee80211_vif *vif, |
| u16 ac, bool enable) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct wmi_sta_uapsd_auto_trig_arg arg = {}; |
| u32 prio = 0, acc = 0; |
| u32 value = 0; |
| int ret = 0; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (arvif->vdev_type != WMI_VDEV_TYPE_STA) |
| return 0; |
| |
| switch (ac) { |
| case IEEE80211_AC_VO: |
| value = WMI_STA_PS_UAPSD_AC3_DELIVERY_EN | |
| WMI_STA_PS_UAPSD_AC3_TRIGGER_EN; |
| prio = 7; |
| acc = 3; |
| break; |
| case IEEE80211_AC_VI: |
| value = WMI_STA_PS_UAPSD_AC2_DELIVERY_EN | |
| WMI_STA_PS_UAPSD_AC2_TRIGGER_EN; |
| prio = 5; |
| acc = 2; |
| break; |
| case IEEE80211_AC_BE: |
| value = WMI_STA_PS_UAPSD_AC1_DELIVERY_EN | |
| WMI_STA_PS_UAPSD_AC1_TRIGGER_EN; |
| prio = 2; |
| acc = 1; |
| break; |
| case IEEE80211_AC_BK: |
| value = WMI_STA_PS_UAPSD_AC0_DELIVERY_EN | |
| WMI_STA_PS_UAPSD_AC0_TRIGGER_EN; |
| prio = 0; |
| acc = 0; |
| break; |
| } |
| |
| if (enable) |
| arvif->u.sta.uapsd |= value; |
| else |
| arvif->u.sta.uapsd &= ~value; |
| |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, |
| WMI_STA_PS_PARAM_UAPSD, |
| arvif->u.sta.uapsd); |
| if (ret) { |
| ath10k_warn(ar, "failed to set uapsd params: %d\n", ret); |
| goto exit; |
| } |
| |
| if (arvif->u.sta.uapsd) |
| value = WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD; |
| else |
| value = WMI_STA_PS_RX_WAKE_POLICY_WAKE; |
| |
| ret = ath10k_wmi_set_sta_ps_param(ar, arvif->vdev_id, |
| WMI_STA_PS_PARAM_RX_WAKE_POLICY, |
| value); |
| if (ret) |
| ath10k_warn(ar, "failed to set rx wake param: %d\n", ret); |
| |
| ret = ath10k_mac_vif_recalc_ps_wake_threshold(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc ps wake threshold on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| ret = ath10k_mac_vif_recalc_ps_poll_count(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to recalc ps poll count on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| |
| if (test_bit(WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, ar->wmi.svc_map) || |
| test_bit(WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, ar->wmi.svc_map)) { |
| /* Only userspace can make an educated decision when to send |
| * trigger frame. The following effectively disables u-UAPSD |
| * autotrigger in firmware (which is enabled by default |
| * provided the autotrigger service is available). |
| */ |
| |
| arg.wmm_ac = acc; |
| arg.user_priority = prio; |
| arg.service_interval = 0; |
| arg.suspend_interval = WMI_STA_UAPSD_MAX_INTERVAL_MSEC; |
| arg.delay_interval = WMI_STA_UAPSD_MAX_INTERVAL_MSEC; |
| |
| ret = ath10k_wmi_vdev_sta_uapsd(ar, arvif->vdev_id, |
| arvif->bssid, &arg, 1); |
| if (ret) { |
| ath10k_warn(ar, "failed to set uapsd auto trigger %d\n", |
| ret); |
| return ret; |
| } |
| } |
| |
| exit: |
| return ret; |
| } |
| |
| static int ath10k_conf_tx(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| unsigned int link_id, u16 ac, |
| const struct ieee80211_tx_queue_params *params) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct wmi_wmm_params_arg *p = NULL; |
| int ret; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| switch (ac) { |
| case IEEE80211_AC_VO: |
| p = &arvif->wmm_params.ac_vo; |
| break; |
| case IEEE80211_AC_VI: |
| p = &arvif->wmm_params.ac_vi; |
| break; |
| case IEEE80211_AC_BE: |
| p = &arvif->wmm_params.ac_be; |
| break; |
| case IEEE80211_AC_BK: |
| p = &arvif->wmm_params.ac_bk; |
| break; |
| } |
| |
| if (WARN_ON(!p)) { |
| ret = -EINVAL; |
| goto exit; |
| } |
| |
| p->cwmin = params->cw_min; |
| p->cwmax = params->cw_max; |
| p->aifs = params->aifs; |
| |
| /* |
| * The channel time duration programmed in the HW is in absolute |
| * microseconds, while mac80211 gives the txop in units of |
| * 32 microseconds. |
| */ |
| p->txop = params->txop * 32; |
| |
| if (ar->wmi.ops->gen_vdev_wmm_conf) { |
| ret = ath10k_wmi_vdev_wmm_conf(ar, arvif->vdev_id, |
| &arvif->wmm_params); |
| if (ret) { |
| ath10k_warn(ar, "failed to set vdev wmm params on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto exit; |
| } |
| } else { |
| /* This won't work well with multi-interface cases but it's |
| * better than nothing. |
| */ |
| ret = ath10k_wmi_pdev_set_wmm_params(ar, &arvif->wmm_params); |
| if (ret) { |
| ath10k_warn(ar, "failed to set wmm params: %d\n", ret); |
| goto exit; |
| } |
| } |
| |
| ret = ath10k_conf_tx_uapsd(ar, vif, ac, params->uapsd); |
| if (ret) |
| ath10k_warn(ar, "failed to set sta uapsd: %d\n", ret); |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static int ath10k_remain_on_channel(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_channel *chan, |
| int duration, |
| enum ieee80211_roc_type type) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct wmi_start_scan_arg arg; |
| int ret = 0; |
| u32 scan_time_msec; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (ath10k_mac_tdls_vif_stations_count(hw, vif) > 0) { |
| ret = -EBUSY; |
| goto exit; |
| } |
| |
| spin_lock_bh(&ar->data_lock); |
| switch (ar->scan.state) { |
| case ATH10K_SCAN_IDLE: |
| reinit_completion(&ar->scan.started); |
| reinit_completion(&ar->scan.completed); |
| reinit_completion(&ar->scan.on_channel); |
| ar->scan.state = ATH10K_SCAN_STARTING; |
| ar->scan.is_roc = true; |
| ar->scan.vdev_id = arvif->vdev_id; |
| ar->scan.roc_freq = chan->center_freq; |
| ar->scan.roc_notify = true; |
| ret = 0; |
| break; |
| case ATH10K_SCAN_STARTING: |
| case ATH10K_SCAN_RUNNING: |
| case ATH10K_SCAN_ABORTING: |
| ret = -EBUSY; |
| break; |
| } |
| spin_unlock_bh(&ar->data_lock); |
| |
| if (ret) |
| goto exit; |
| |
| scan_time_msec = ar->hw->wiphy->max_remain_on_channel_duration * 2; |
| |
| memset(&arg, 0, sizeof(arg)); |
| ath10k_wmi_start_scan_init(ar, &arg); |
| arg.vdev_id = arvif->vdev_id; |
| arg.scan_id = ATH10K_SCAN_ID; |
| arg.n_channels = 1; |
| arg.channels[0] = chan->center_freq; |
| arg.dwell_time_active = scan_time_msec; |
| arg.dwell_time_passive = scan_time_msec; |
| arg.max_scan_time = scan_time_msec; |
| arg.scan_ctrl_flags |= WMI_SCAN_FLAG_PASSIVE; |
| arg.scan_ctrl_flags |= WMI_SCAN_FILTER_PROBE_REQ; |
| arg.burst_duration_ms = duration; |
| |
| ret = ath10k_start_scan(ar, &arg); |
| if (ret) { |
| ath10k_warn(ar, "failed to start roc scan: %d\n", ret); |
| spin_lock_bh(&ar->data_lock); |
| ar->scan.state = ATH10K_SCAN_IDLE; |
| spin_unlock_bh(&ar->data_lock); |
| goto exit; |
| } |
| |
| ret = wait_for_completion_timeout(&ar->scan.on_channel, 3 * HZ); |
| if (ret == 0) { |
| ath10k_warn(ar, "failed to switch to channel for roc scan\n"); |
| |
| ret = ath10k_scan_stop(ar); |
| if (ret) |
| ath10k_warn(ar, "failed to stop scan: %d\n", ret); |
| |
| ret = -ETIMEDOUT; |
| goto exit; |
| } |
| |
| ieee80211_queue_delayed_work(ar->hw, &ar->scan.timeout, |
| msecs_to_jiffies(duration)); |
| |
| ret = 0; |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static int ath10k_cancel_remain_on_channel(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| ar->scan.roc_notify = false; |
| spin_unlock_bh(&ar->data_lock); |
| |
| ath10k_scan_abort(ar); |
| |
| mutex_unlock(&ar->conf_mutex); |
| |
| cancel_delayed_work_sync(&ar->scan.timeout); |
| |
| return 0; |
| } |
| |
| /* |
| * Both RTS and Fragmentation threshold are interface-specific |
| * in ath10k, but device-specific in mac80211. |
| */ |
| |
| static int ath10k_set_rts_threshold(struct ieee80211_hw *hw, u32 value) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif; |
| int ret = 0; |
| |
| mutex_lock(&ar->conf_mutex); |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac vdev %d rts threshold %d\n", |
| arvif->vdev_id, value); |
| |
| ret = ath10k_mac_set_rts(arvif, value); |
| if (ret) { |
| ath10k_warn(ar, "failed to set rts threshold for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| break; |
| } |
| } |
| mutex_unlock(&ar->conf_mutex); |
| |
| return ret; |
| } |
| |
| static int ath10k_mac_op_set_frag_threshold(struct ieee80211_hw *hw, u32 value) |
| { |
| /* Even though there's a WMI enum for fragmentation threshold no known |
| * firmware actually implements it. Moreover it is not possible to rely |
| * frame fragmentation to mac80211 because firmware clears the "more |
| * fragments" bit in frame control making it impossible for remote |
| * devices to reassemble frames. |
| * |
| * Hence implement a dummy callback just to say fragmentation isn't |
| * supported. This effectively prevents mac80211 from doing frame |
| * fragmentation in software. |
| */ |
| return -EOPNOTSUPP; |
| } |
| |
| void ath10k_mac_wait_tx_complete(struct ath10k *ar) |
| { |
| bool skip; |
| long time_left; |
| |
| /* mac80211 doesn't care if we really xmit queued frames or not |
| * we'll collect those frames either way if we stop/delete vdevs |
| */ |
| |
| if (ar->state == ATH10K_STATE_WEDGED) |
| return; |
| |
| time_left = wait_event_timeout(ar->htt.empty_tx_wq, ({ |
| bool empty; |
| |
| spin_lock_bh(&ar->htt.tx_lock); |
| empty = (ar->htt.num_pending_tx == 0); |
| spin_unlock_bh(&ar->htt.tx_lock); |
| |
| skip = (ar->state == ATH10K_STATE_WEDGED) || |
| test_bit(ATH10K_FLAG_CRASH_FLUSH, |
| &ar->dev_flags); |
| |
| (empty || skip); |
| }), ATH10K_FLUSH_TIMEOUT_HZ); |
| |
| if (time_left == 0 || skip) |
| ath10k_warn(ar, "failed to flush transmit queue (skip %i ar-state %i): %ld\n", |
| skip, ar->state, time_left); |
| } |
| |
| static void ath10k_flush(struct ieee80211_hw *hw, struct ieee80211_vif *vif, |
| u32 queues, bool drop) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif; |
| u32 bitmap; |
| |
| if (drop) { |
| if (vif && vif->type == NL80211_IFTYPE_STATION) { |
| bitmap = ~(1 << WMI_MGMT_TID); |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| if (arvif->vdev_type == WMI_VDEV_TYPE_STA) |
| ath10k_wmi_peer_flush(ar, arvif->vdev_id, |
| arvif->bssid, bitmap); |
| } |
| ath10k_htt_flush_tx(&ar->htt); |
| } |
| return; |
| } |
| |
| mutex_lock(&ar->conf_mutex); |
| ath10k_mac_wait_tx_complete(ar); |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| /* TODO: Implement this function properly |
| * For now it is needed to reply to Probe Requests in IBSS mode. |
| * Probably we need this information from FW. |
| */ |
| static int ath10k_tx_last_beacon(struct ieee80211_hw *hw) |
| { |
| return 1; |
| } |
| |
| static void ath10k_reconfig_complete(struct ieee80211_hw *hw, |
| enum ieee80211_reconfig_type reconfig_type) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif; |
| |
| if (reconfig_type != IEEE80211_RECONFIG_TYPE_RESTART) |
| return; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| /* If device failed to restart it will be in a different state, e.g. |
| * ATH10K_STATE_WEDGED |
| */ |
| if (ar->state == ATH10K_STATE_RESTARTED) { |
| ath10k_info(ar, "device successfully recovered\n"); |
| ar->state = ATH10K_STATE_ON; |
| ieee80211_wake_queues(ar->hw); |
| clear_bit(ATH10K_FLAG_RESTARTING, &ar->dev_flags); |
| if (ar->hw_params.hw_restart_disconnect) { |
| list_for_each_entry(arvif, &ar->arvifs, list) { |
| if (arvif->is_up && arvif->vdev_type == WMI_VDEV_TYPE_STA) |
| ieee80211_hw_restart_disconnect(arvif->vif); |
| } |
| } |
| } |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static void |
| ath10k_mac_update_bss_chan_survey(struct ath10k *ar, |
| struct ieee80211_channel *channel) |
| { |
| int ret; |
| enum wmi_bss_survey_req_type type = WMI_BSS_SURVEY_REQ_TYPE_READ; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| if (!test_bit(WMI_SERVICE_BSS_CHANNEL_INFO_64, ar->wmi.svc_map) || |
| (ar->rx_channel != channel)) |
| return; |
| |
| if (ar->scan.state != ATH10K_SCAN_IDLE) { |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "ignoring bss chan info request while scanning..\n"); |
| return; |
| } |
| |
| reinit_completion(&ar->bss_survey_done); |
| |
| ret = ath10k_wmi_pdev_bss_chan_info_request(ar, type); |
| if (ret) { |
| ath10k_warn(ar, "failed to send pdev bss chan info request\n"); |
| return; |
| } |
| |
| ret = wait_for_completion_timeout(&ar->bss_survey_done, 3 * HZ); |
| if (!ret) { |
| ath10k_warn(ar, "bss channel survey timed out\n"); |
| return; |
| } |
| } |
| |
| static int ath10k_get_survey(struct ieee80211_hw *hw, int idx, |
| struct survey_info *survey) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ieee80211_supported_band *sband; |
| struct survey_info *ar_survey = &ar->survey[idx]; |
| int ret = 0; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| sband = hw->wiphy->bands[NL80211_BAND_2GHZ]; |
| if (sband && idx >= sband->n_channels) { |
| idx -= sband->n_channels; |
| sband = NULL; |
| } |
| |
| if (!sband) |
| sband = hw->wiphy->bands[NL80211_BAND_5GHZ]; |
| |
| if (!sband || idx >= sband->n_channels) { |
| ret = -ENOENT; |
| goto exit; |
| } |
| |
| ath10k_mac_update_bss_chan_survey(ar, &sband->channels[idx]); |
| |
| spin_lock_bh(&ar->data_lock); |
| memcpy(survey, ar_survey, sizeof(*survey)); |
| spin_unlock_bh(&ar->data_lock); |
| |
| survey->channel = &sband->channels[idx]; |
| |
| if (ar->rx_channel == survey->channel) |
| survey->filled |= SURVEY_INFO_IN_USE; |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static bool |
| ath10k_mac_bitrate_mask_get_single_nss(struct ath10k *ar, |
| enum nl80211_band band, |
| const struct cfg80211_bitrate_mask *mask, |
| int *nss) |
| { |
| struct ieee80211_supported_band *sband = &ar->mac.sbands[band]; |
| u16 vht_mcs_map = le16_to_cpu(sband->vht_cap.vht_mcs.tx_mcs_map); |
| u8 ht_nss_mask = 0; |
| u8 vht_nss_mask = 0; |
| int i; |
| |
| if (mask->control[band].legacy) |
| return false; |
| |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].ht_mcs); i++) { |
| if (mask->control[band].ht_mcs[i] == 0) |
| continue; |
| else if (mask->control[band].ht_mcs[i] == |
| sband->ht_cap.mcs.rx_mask[i]) |
| ht_nss_mask |= BIT(i); |
| else |
| return false; |
| } |
| |
| for (i = 0; i < ARRAY_SIZE(mask->control[band].vht_mcs); i++) { |
| if (mask->control[band].vht_mcs[i] == 0) |
| continue; |
| else if (mask->control[band].vht_mcs[i] == |
| ath10k_mac_get_max_vht_mcs_map(vht_mcs_map, i)) |
| vht_nss_mask |= BIT(i); |
| else |
| return false; |
| } |
| |
| if (ht_nss_mask != vht_nss_mask) |
| return false; |
| |
| if (ht_nss_mask == 0) |
| return false; |
| |
| if (BIT(fls(ht_nss_mask)) - 1 != ht_nss_mask) |
| return false; |
| |
| *nss = fls(ht_nss_mask); |
| |
| return true; |
| } |
| |
| static int ath10k_mac_set_fixed_rate_params(struct ath10k_vif *arvif, |
| u8 rate, u8 nss, u8 sgi, u8 ldpc) |
| { |
| struct ath10k *ar = arvif->ar; |
| u32 vdev_param; |
| int ret; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac set fixed rate params vdev %i rate 0x%02x nss %u sgi %u\n", |
| arvif->vdev_id, rate, nss, sgi); |
| |
| vdev_param = ar->wmi.vdev_param->fixed_rate; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, rate); |
| if (ret) { |
| ath10k_warn(ar, "failed to set fixed rate param 0x%02x: %d\n", |
| rate, ret); |
| return ret; |
| } |
| |
| vdev_param = ar->wmi.vdev_param->nss; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, nss); |
| if (ret) { |
| ath10k_warn(ar, "failed to set nss param %d: %d\n", nss, ret); |
| return ret; |
| } |
| |
| vdev_param = ar->wmi.vdev_param->sgi; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, sgi); |
| if (ret) { |
| ath10k_warn(ar, "failed to set sgi param %d: %d\n", sgi, ret); |
| return ret; |
| } |
| |
| vdev_param = ar->wmi.vdev_param->ldpc; |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, vdev_param, ldpc); |
| if (ret) { |
| ath10k_warn(ar, "failed to set ldpc param %d: %d\n", ldpc, ret); |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static bool |
| ath10k_mac_can_set_bitrate_mask(struct ath10k *ar, |
| enum nl80211_band band, |
| const struct cfg80211_bitrate_mask *mask, |
| bool allow_pfr) |
| { |
| int i; |
| u16 vht_mcs; |
| |
| /* Due to firmware limitation in WMI_PEER_ASSOC_CMDID it is impossible |
| * to express all VHT MCS rate masks. Effectively only the following |
| * ranges can be used: none, 0-7, 0-8 and 0-9. |
| */ |
| for (i = 0; i < NL80211_VHT_NSS_MAX; i++) { |
| vht_mcs = mask->control[band].vht_mcs[i]; |
| |
| switch (vht_mcs) { |
| case 0: |
| case BIT(8) - 1: |
| case BIT(9) - 1: |
| case BIT(10) - 1: |
| break; |
| default: |
| if (!allow_pfr) |
| ath10k_warn(ar, "refusing bitrate mask with missing 0-7 VHT MCS rates\n"); |
| return false; |
| } |
| } |
| |
| return true; |
| } |
| |
| static bool ath10k_mac_set_vht_bitrate_mask_fixup(struct ath10k *ar, |
| struct ath10k_vif *arvif, |
| struct ieee80211_sta *sta) |
| { |
| int err; |
| u8 rate = arvif->vht_pfr; |
| |
| /* skip non vht and multiple rate peers */ |
| if (!sta->deflink.vht_cap.vht_supported || arvif->vht_num_rates != 1) |
| return false; |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| WMI_PEER_PARAM_FIXED_RATE, rate); |
| if (err) |
| ath10k_warn(ar, "failed to enable STA %pM peer fixed rate: %d\n", |
| sta->addr, err); |
| |
| return true; |
| } |
| |
| static void ath10k_mac_set_bitrate_mask_iter(void *data, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k_vif *arvif = data; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k *ar = arvif->ar; |
| |
| if (arsta->arvif != arvif) |
| return; |
| |
| if (ath10k_mac_set_vht_bitrate_mask_fixup(ar, arvif, sta)) |
| return; |
| |
| spin_lock_bh(&ar->data_lock); |
| arsta->changed |= IEEE80211_RC_SUPP_RATES_CHANGED; |
| spin_unlock_bh(&ar->data_lock); |
| |
| ieee80211_queue_work(ar->hw, &arsta->update_wk); |
| } |
| |
| static void ath10k_mac_clr_bitrate_mask_iter(void *data, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k_vif *arvif = data; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k *ar = arvif->ar; |
| int err; |
| |
| /* clear vht peers only */ |
| if (arsta->arvif != arvif || !sta->deflink.vht_cap.vht_supported) |
| return; |
| |
| err = ath10k_wmi_peer_set_param(ar, arvif->vdev_id, sta->addr, |
| WMI_PEER_PARAM_FIXED_RATE, |
| WMI_FIXED_RATE_NONE); |
| if (err) |
| ath10k_warn(ar, "failed to clear STA %pM peer fixed rate: %d\n", |
| sta->addr, err); |
| } |
| |
| static int ath10k_mac_op_set_bitrate_mask(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| const struct cfg80211_bitrate_mask *mask) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct cfg80211_chan_def def; |
| struct ath10k *ar = arvif->ar; |
| enum nl80211_band band; |
| const u8 *ht_mcs_mask; |
| const u16 *vht_mcs_mask; |
| u8 rate; |
| u8 nss; |
| u8 sgi; |
| u8 ldpc; |
| int single_nss; |
| int ret; |
| int vht_num_rates, allow_pfr; |
| u8 vht_pfr; |
| bool update_bitrate_mask = true; |
| |
| if (ath10k_mac_vif_chan(vif, &def)) |
| return -EPERM; |
| |
| band = def.chan->band; |
| ht_mcs_mask = mask->control[band].ht_mcs; |
| vht_mcs_mask = mask->control[band].vht_mcs; |
| ldpc = !!(ar->ht_cap_info & WMI_HT_CAP_LDPC); |
| |
| sgi = mask->control[band].gi; |
| if (sgi == NL80211_TXRATE_FORCE_LGI) |
| return -EINVAL; |
| |
| allow_pfr = test_bit(ATH10K_FW_FEATURE_PEER_FIXED_RATE, |
| ar->normal_mode_fw.fw_file.fw_features); |
| if (allow_pfr) { |
| mutex_lock(&ar->conf_mutex); |
| ieee80211_iterate_stations_atomic(ar->hw, |
| ath10k_mac_clr_bitrate_mask_iter, |
| arvif); |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| if (ath10k_mac_bitrate_mask_has_single_rate(ar, band, mask, |
| &vht_num_rates)) { |
| ret = ath10k_mac_bitrate_mask_get_single_rate(ar, band, mask, |
| &rate, &nss, |
| false); |
| if (ret) { |
| ath10k_warn(ar, "failed to get single rate for vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| return ret; |
| } |
| } else if (ath10k_mac_bitrate_mask_get_single_nss(ar, band, mask, |
| &single_nss)) { |
| rate = WMI_FIXED_RATE_NONE; |
| nss = single_nss; |
| } else { |
| rate = WMI_FIXED_RATE_NONE; |
| nss = min(ar->num_rf_chains, |
| max(ath10k_mac_max_ht_nss(ht_mcs_mask), |
| ath10k_mac_max_vht_nss(vht_mcs_mask))); |
| |
| if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask, |
| allow_pfr)) { |
| u8 vht_nss; |
| |
| if (!allow_pfr || vht_num_rates != 1) |
| return -EINVAL; |
| |
| /* Reach here, firmware supports peer fixed rate and has |
| * single vht rate, and don't update vif birate_mask, as |
| * the rate only for specific peer. |
| */ |
| ath10k_mac_bitrate_mask_get_single_rate(ar, band, mask, |
| &vht_pfr, |
| &vht_nss, |
| true); |
| update_bitrate_mask = false; |
| } else { |
| vht_pfr = 0; |
| } |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (update_bitrate_mask) |
| arvif->bitrate_mask = *mask; |
| arvif->vht_num_rates = vht_num_rates; |
| arvif->vht_pfr = vht_pfr; |
| ieee80211_iterate_stations_atomic(ar->hw, |
| ath10k_mac_set_bitrate_mask_iter, |
| arvif); |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ret = ath10k_mac_set_fixed_rate_params(arvif, rate, nss, sgi, ldpc); |
| if (ret) { |
| ath10k_warn(ar, "failed to set fixed rate params on vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto exit; |
| } |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| |
| return ret; |
| } |
| |
| static void ath10k_sta_rc_update(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| u32 changed) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_peer *peer; |
| u32 bw, smps; |
| |
| spin_lock_bh(&ar->data_lock); |
| |
| peer = ath10k_peer_find(ar, arvif->vdev_id, sta->addr); |
| if (!peer) { |
| spin_unlock_bh(&ar->data_lock); |
| ath10k_warn(ar, "mac sta rc update failed to find peer %pM on vdev %i\n", |
| sta->addr, arvif->vdev_id); |
| return; |
| } |
| |
| ath10k_dbg(ar, ATH10K_DBG_STA, |
| "mac sta rc update for %pM changed %08x bw %d nss %d smps %d\n", |
| sta->addr, changed, sta->deflink.bandwidth, |
| sta->deflink.rx_nss, |
| sta->deflink.smps_mode); |
| |
| if (changed & IEEE80211_RC_BW_CHANGED) { |
| bw = WMI_PEER_CHWIDTH_20MHZ; |
| |
| switch (sta->deflink.bandwidth) { |
| case IEEE80211_STA_RX_BW_20: |
| bw = WMI_PEER_CHWIDTH_20MHZ; |
| break; |
| case IEEE80211_STA_RX_BW_40: |
| bw = WMI_PEER_CHWIDTH_40MHZ; |
| break; |
| case IEEE80211_STA_RX_BW_80: |
| bw = WMI_PEER_CHWIDTH_80MHZ; |
| break; |
| case IEEE80211_STA_RX_BW_160: |
| bw = WMI_PEER_CHWIDTH_160MHZ; |
| break; |
| default: |
| ath10k_warn(ar, "Invalid bandwidth %d in rc update for %pM\n", |
| sta->deflink.bandwidth, sta->addr); |
| bw = WMI_PEER_CHWIDTH_20MHZ; |
| break; |
| } |
| |
| arsta->bw = bw; |
| } |
| |
| if (changed & IEEE80211_RC_NSS_CHANGED) |
| arsta->nss = sta->deflink.rx_nss; |
| |
| if (changed & IEEE80211_RC_SMPS_CHANGED) { |
| smps = WMI_PEER_SMPS_PS_NONE; |
| |
| switch (sta->deflink.smps_mode) { |
| case IEEE80211_SMPS_AUTOMATIC: |
| case IEEE80211_SMPS_OFF: |
| smps = WMI_PEER_SMPS_PS_NONE; |
| break; |
| case IEEE80211_SMPS_STATIC: |
| smps = WMI_PEER_SMPS_STATIC; |
| break; |
| case IEEE80211_SMPS_DYNAMIC: |
| smps = WMI_PEER_SMPS_DYNAMIC; |
| break; |
| case IEEE80211_SMPS_NUM_MODES: |
| ath10k_warn(ar, "Invalid smps %d in sta rc update for %pM\n", |
| sta->deflink.smps_mode, sta->addr); |
| smps = WMI_PEER_SMPS_PS_NONE; |
| break; |
| } |
| |
| arsta->smps = smps; |
| } |
| |
| arsta->changed |= changed; |
| |
| spin_unlock_bh(&ar->data_lock); |
| |
| ieee80211_queue_work(hw, &arsta->update_wk); |
| } |
| |
| static void ath10k_offset_tsf(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, s64 tsf_offset) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| u32 offset, vdev_param; |
| int ret; |
| |
| if (tsf_offset < 0) { |
| vdev_param = ar->wmi.vdev_param->dec_tsf; |
| offset = -tsf_offset; |
| } else { |
| vdev_param = ar->wmi.vdev_param->inc_tsf; |
| offset = tsf_offset; |
| } |
| |
| ret = ath10k_wmi_vdev_set_param(ar, arvif->vdev_id, |
| vdev_param, offset); |
| |
| if (ret && ret != -EOPNOTSUPP) |
| ath10k_warn(ar, "failed to set tsf offset %d cmd %d: %d\n", |
| offset, vdev_param, ret); |
| } |
| |
| static int ath10k_ampdu_action(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_ampdu_params *params) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ieee80211_sta *sta = params->sta; |
| enum ieee80211_ampdu_mlme_action action = params->action; |
| u16 tid = params->tid; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac ampdu vdev_id %i sta %pM tid %u action %d\n", |
| arvif->vdev_id, sta->addr, tid, action); |
| |
| switch (action) { |
| case IEEE80211_AMPDU_RX_START: |
| case IEEE80211_AMPDU_RX_STOP: |
| /* HTT AddBa/DelBa events trigger mac80211 Rx BA session |
| * creation/removal. Do we need to verify this? |
| */ |
| return 0; |
| case IEEE80211_AMPDU_TX_START: |
| case IEEE80211_AMPDU_TX_STOP_CONT: |
| case IEEE80211_AMPDU_TX_STOP_FLUSH: |
| case IEEE80211_AMPDU_TX_STOP_FLUSH_CONT: |
| case IEEE80211_AMPDU_TX_OPERATIONAL: |
| /* Firmware offloads Tx aggregation entirely so deny mac80211 |
| * Tx aggregation requests. |
| */ |
| return -EOPNOTSUPP; |
| } |
| |
| return -EINVAL; |
| } |
| |
| static void |
| ath10k_mac_update_rx_channel(struct ath10k *ar, |
| struct ieee80211_chanctx_conf *ctx, |
| struct ieee80211_vif_chanctx_switch *vifs, |
| int n_vifs) |
| { |
| struct cfg80211_chan_def *def = NULL; |
| |
| /* Both locks are required because ar->rx_channel is modified. This |
| * allows readers to hold either lock. |
| */ |
| lockdep_assert_held(&ar->conf_mutex); |
| lockdep_assert_held(&ar->data_lock); |
| |
| WARN_ON(ctx && vifs); |
| WARN_ON(vifs && !n_vifs); |
| |
| /* FIXME: Sort of an optimization and a workaround. Peers and vifs are |
| * on a linked list now. Doing a lookup peer -> vif -> chanctx for each |
| * ppdu on Rx may reduce performance on low-end systems. It should be |
| * possible to make tables/hashmaps to speed the lookup up (be vary of |
| * cpu data cache lines though regarding sizes) but to keep the initial |
| * implementation simple and less intrusive fallback to the slow lookup |
| * only for multi-channel cases. Single-channel cases will remain to |
| * use the old channel derival and thus performance should not be |
| * affected much. |
| */ |
| rcu_read_lock(); |
| if (!ctx && ath10k_mac_num_chanctxs(ar) == 1) { |
| ieee80211_iter_chan_contexts_atomic(ar->hw, |
| ath10k_mac_get_any_chandef_iter, |
| &def); |
| |
| if (vifs) |
| def = &vifs[0].new_ctx->def; |
| |
| ar->rx_channel = def->chan; |
| } else if ((ctx && ath10k_mac_num_chanctxs(ar) == 0) || |
| (ctx && (ar->state == ATH10K_STATE_RESTARTED))) { |
| /* During driver restart due to firmware assert, since mac80211 |
| * already has valid channel context for given radio, channel |
| * context iteration return num_chanctx > 0. So fix rx_channel |
| * when restart is in progress. |
| */ |
| ar->rx_channel = ctx->def.chan; |
| } else { |
| ar->rx_channel = NULL; |
| } |
| rcu_read_unlock(); |
| } |
| |
| static void |
| ath10k_mac_update_vif_chan(struct ath10k *ar, |
| struct ieee80211_vif_chanctx_switch *vifs, |
| int n_vifs) |
| { |
| struct ath10k_vif *arvif; |
| int ret; |
| int i; |
| |
| lockdep_assert_held(&ar->conf_mutex); |
| |
| /* First stop monitor interface. Some FW versions crash if there's a |
| * lone monitor interface. |
| */ |
| if (ar->monitor_started) |
| ath10k_monitor_stop(ar); |
| |
| for (i = 0; i < n_vifs; i++) { |
| arvif = (void *)vifs[i].vif->drv_priv; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx switch vdev_id %i freq %u->%u width %d->%d\n", |
| arvif->vdev_id, |
| vifs[i].old_ctx->def.chan->center_freq, |
| vifs[i].new_ctx->def.chan->center_freq, |
| vifs[i].old_ctx->def.width, |
| vifs[i].new_ctx->def.width); |
| |
| if (WARN_ON(!arvif->is_started)) |
| continue; |
| |
| if (WARN_ON(!arvif->is_up)) |
| continue; |
| |
| ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id); |
| if (ret) { |
| ath10k_warn(ar, "failed to down vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| continue; |
| } |
| } |
| |
| /* All relevant vdevs are downed and associated channel resources |
| * should be available for the channel switch now. |
| */ |
| |
| spin_lock_bh(&ar->data_lock); |
| ath10k_mac_update_rx_channel(ar, NULL, vifs, n_vifs); |
| spin_unlock_bh(&ar->data_lock); |
| |
| for (i = 0; i < n_vifs; i++) { |
| arvif = (void *)vifs[i].vif->drv_priv; |
| |
| if (WARN_ON(!arvif->is_started)) |
| continue; |
| |
| if (WARN_ON(!arvif->is_up)) |
| continue; |
| |
| ret = ath10k_mac_setup_bcn_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to update bcn tmpl during csa: %d\n", |
| ret); |
| |
| ret = ath10k_mac_setup_prb_tmpl(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to update prb tmpl during csa: %d\n", |
| ret); |
| |
| ret = ath10k_vdev_restart(arvif, &vifs[i].new_ctx->def); |
| if (ret) { |
| ath10k_warn(ar, "failed to restart vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| continue; |
| } |
| |
| ret = ath10k_wmi_vdev_up(arvif->ar, arvif->vdev_id, arvif->aid, |
| arvif->bssid); |
| if (ret) { |
| ath10k_warn(ar, "failed to bring vdev up %d: %d\n", |
| arvif->vdev_id, ret); |
| continue; |
| } |
| } |
| |
| ath10k_monitor_recalc(ar); |
| } |
| |
| static int |
| ath10k_mac_op_add_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *ctx) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx add freq %u width %d ptr %pK\n", |
| ctx->def.chan->center_freq, ctx->def.width, ctx); |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| ath10k_mac_update_rx_channel(ar, ctx, NULL, 0); |
| spin_unlock_bh(&ar->data_lock); |
| |
| ath10k_recalc_radar_detection(ar); |
| ath10k_monitor_recalc(ar); |
| |
| mutex_unlock(&ar->conf_mutex); |
| |
| return 0; |
| } |
| |
| static void |
| ath10k_mac_op_remove_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *ctx) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx remove freq %u width %d ptr %pK\n", |
| ctx->def.chan->center_freq, ctx->def.width, ctx); |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| spin_lock_bh(&ar->data_lock); |
| ath10k_mac_update_rx_channel(ar, NULL, NULL, 0); |
| spin_unlock_bh(&ar->data_lock); |
| |
| ath10k_recalc_radar_detection(ar); |
| ath10k_monitor_recalc(ar); |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| struct ath10k_mac_change_chanctx_arg { |
| struct ieee80211_chanctx_conf *ctx; |
| struct ieee80211_vif_chanctx_switch *vifs; |
| int n_vifs; |
| int next_vif; |
| }; |
| |
| static void |
| ath10k_mac_change_chanctx_cnt_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_mac_change_chanctx_arg *arg = data; |
| |
| if (rcu_access_pointer(vif->bss_conf.chanctx_conf) != arg->ctx) |
| return; |
| |
| arg->n_vifs++; |
| } |
| |
| static void |
| ath10k_mac_change_chanctx_fill_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_mac_change_chanctx_arg *arg = data; |
| struct ieee80211_chanctx_conf *ctx; |
| |
| ctx = rcu_access_pointer(vif->bss_conf.chanctx_conf); |
| if (ctx != arg->ctx) |
| return; |
| |
| if (WARN_ON(arg->next_vif == arg->n_vifs)) |
| return; |
| |
| arg->vifs[arg->next_vif].vif = vif; |
| arg->vifs[arg->next_vif].old_ctx = ctx; |
| arg->vifs[arg->next_vif].new_ctx = ctx; |
| arg->next_vif++; |
| } |
| |
| static void |
| ath10k_mac_op_change_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_chanctx_conf *ctx, |
| u32 changed) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_mac_change_chanctx_arg arg = { .ctx = ctx }; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx change freq %u width %d ptr %pK changed %x\n", |
| ctx->def.chan->center_freq, ctx->def.width, ctx, changed); |
| |
| /* This shouldn't really happen because channel switching should use |
| * switch_vif_chanctx(). |
| */ |
| if (WARN_ON(changed & IEEE80211_CHANCTX_CHANGE_CHANNEL)) |
| goto unlock; |
| |
| if (changed & IEEE80211_CHANCTX_CHANGE_WIDTH) { |
| ieee80211_iterate_active_interfaces_atomic( |
| hw, |
| ATH10K_ITER_NORMAL_FLAGS, |
| ath10k_mac_change_chanctx_cnt_iter, |
| &arg); |
| if (arg.n_vifs == 0) |
| goto radar; |
| |
| arg.vifs = kcalloc(arg.n_vifs, sizeof(arg.vifs[0]), |
| GFP_KERNEL); |
| if (!arg.vifs) |
| goto radar; |
| |
| ieee80211_iterate_active_interfaces_atomic( |
| hw, |
| ATH10K_ITER_NORMAL_FLAGS, |
| ath10k_mac_change_chanctx_fill_iter, |
| &arg); |
| ath10k_mac_update_vif_chan(ar, arg.vifs, arg.n_vifs); |
| kfree(arg.vifs); |
| } |
| |
| radar: |
| ath10k_recalc_radar_detection(ar); |
| |
| /* FIXME: How to configure Rx chains properly? */ |
| |
| /* No other actions are actually necessary. Firmware maintains channel |
| * definitions per vdev internally and there's no host-side channel |
| * context abstraction to configure, e.g. channel width. |
| */ |
| |
| unlock: |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static int |
| ath10k_mac_op_assign_vif_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *link_conf, |
| struct ieee80211_chanctx_conf *ctx) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx assign ptr %pK vdev_id %i\n", |
| ctx, arvif->vdev_id); |
| |
| if (WARN_ON(arvif->is_started)) { |
| mutex_unlock(&ar->conf_mutex); |
| return -EBUSY; |
| } |
| |
| ret = ath10k_vdev_start(arvif, &ctx->def); |
| if (ret) { |
| ath10k_warn(ar, "failed to start vdev %i addr %pM on freq %d: %d\n", |
| arvif->vdev_id, vif->addr, |
| ctx->def.chan->center_freq, ret); |
| goto err; |
| } |
| |
| arvif->is_started = true; |
| |
| ret = ath10k_mac_vif_setup_ps(arvif); |
| if (ret) { |
| ath10k_warn(ar, "failed to update vdev %i ps: %d\n", |
| arvif->vdev_id, ret); |
| goto err_stop; |
| } |
| |
| if (vif->type == NL80211_IFTYPE_MONITOR) { |
| ret = ath10k_wmi_vdev_up(ar, arvif->vdev_id, 0, vif->addr); |
| if (ret) { |
| ath10k_warn(ar, "failed to up monitor vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| goto err_stop; |
| } |
| |
| arvif->is_up = true; |
| } |
| |
| if (ath10k_mac_can_set_cts_prot(arvif)) { |
| ret = ath10k_mac_set_cts_prot(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to set cts protection for vdev %d: %d\n", |
| arvif->vdev_id, ret); |
| } |
| |
| if (ath10k_peer_stats_enabled(ar) && |
| ar->hw_params.tx_stats_over_pktlog) { |
| ar->pktlog_filter |= ATH10K_PKTLOG_PEER_STATS; |
| ret = ath10k_wmi_pdev_pktlog_enable(ar, |
| ar->pktlog_filter); |
| if (ret) { |
| ath10k_warn(ar, "failed to enable pktlog %d\n", ret); |
| goto err_stop; |
| } |
| } |
| |
| mutex_unlock(&ar->conf_mutex); |
| return 0; |
| |
| err_stop: |
| ath10k_vdev_stop(arvif); |
| arvif->is_started = false; |
| ath10k_mac_vif_setup_ps(arvif); |
| |
| err: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static void |
| ath10k_mac_op_unassign_vif_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_bss_conf *link_conf, |
| struct ieee80211_chanctx_conf *ctx) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| int ret; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx unassign ptr %pK vdev_id %i\n", |
| ctx, arvif->vdev_id); |
| |
| WARN_ON(!arvif->is_started); |
| |
| if (vif->type == NL80211_IFTYPE_MONITOR) { |
| WARN_ON(!arvif->is_up); |
| |
| ret = ath10k_wmi_vdev_down(ar, arvif->vdev_id); |
| if (ret) |
| ath10k_warn(ar, "failed to down monitor vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| arvif->is_up = false; |
| } |
| |
| ret = ath10k_vdev_stop(arvif); |
| if (ret) |
| ath10k_warn(ar, "failed to stop vdev %i: %d\n", |
| arvif->vdev_id, ret); |
| |
| arvif->is_started = false; |
| |
| mutex_unlock(&ar->conf_mutex); |
| } |
| |
| static int |
| ath10k_mac_op_switch_vif_chanctx(struct ieee80211_hw *hw, |
| struct ieee80211_vif_chanctx_switch *vifs, |
| int n_vifs, |
| enum ieee80211_chanctx_switch_mode mode) |
| { |
| struct ath10k *ar = hw->priv; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac chanctx switch n_vifs %d mode %d\n", |
| n_vifs, mode); |
| ath10k_mac_update_vif_chan(ar, vifs, n_vifs); |
| |
| mutex_unlock(&ar->conf_mutex); |
| return 0; |
| } |
| |
| static void ath10k_mac_op_sta_pre_rcu_remove(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta) |
| { |
| struct ath10k *ar; |
| struct ath10k_peer *peer; |
| |
| ar = hw->priv; |
| |
| list_for_each_entry(peer, &ar->peers, list) |
| if (peer->sta == sta) |
| peer->removed = true; |
| } |
| |
| /* HT MCS parameters with Nss = 1 */ |
| static const struct ath10k_index_ht_data_rate_type supported_ht_mcs_rate_nss1[] = { |
| /* MCS L20 L40 S20 S40 */ |
| {0, { 65, 135, 72, 150} }, |
| {1, { 130, 270, 144, 300} }, |
| {2, { 195, 405, 217, 450} }, |
| {3, { 260, 540, 289, 600} }, |
| {4, { 390, 810, 433, 900} }, |
| {5, { 520, 1080, 578, 1200} }, |
| {6, { 585, 1215, 650, 1350} }, |
| {7, { 650, 1350, 722, 1500} } |
| }; |
| |
| /* HT MCS parameters with Nss = 2 */ |
| static const struct ath10k_index_ht_data_rate_type supported_ht_mcs_rate_nss2[] = { |
| /* MCS L20 L40 S20 S40 */ |
| {0, {130, 270, 144, 300} }, |
| {1, {260, 540, 289, 600} }, |
| {2, {390, 810, 433, 900} }, |
| {3, {520, 1080, 578, 1200} }, |
| {4, {780, 1620, 867, 1800} }, |
| {5, {1040, 2160, 1156, 2400} }, |
| {6, {1170, 2430, 1300, 2700} }, |
| {7, {1300, 2700, 1444, 3000} } |
| }; |
| |
| /* MCS parameters with Nss = 1 */ |
| static const struct ath10k_index_vht_data_rate_type supported_vht_mcs_rate_nss1[] = { |
| /* MCS L80 S80 L40 S40 L20 S20 */ |
| {0, {293, 325}, {135, 150}, {65, 72} }, |
| {1, {585, 650}, {270, 300}, {130, 144} }, |
| {2, {878, 975}, {405, 450}, {195, 217} }, |
| {3, {1170, 1300}, {540, 600}, {260, 289} }, |
| {4, {1755, 1950}, {810, 900}, {390, 433} }, |
| {5, {2340, 2600}, {1080, 1200}, {520, 578} }, |
| {6, {2633, 2925}, {1215, 1350}, {585, 650} }, |
| {7, {2925, 3250}, {1350, 1500}, {650, 722} }, |
| {8, {3510, 3900}, {1620, 1800}, {780, 867} }, |
| {9, {3900, 4333}, {1800, 2000}, {780, 867} } |
| }; |
| |
| /*MCS parameters with Nss = 2 */ |
| static const struct ath10k_index_vht_data_rate_type supported_vht_mcs_rate_nss2[] = { |
| /* MCS L80 S80 L40 S40 L20 S20 */ |
| {0, {585, 650}, {270, 300}, {130, 144} }, |
| {1, {1170, 1300}, {540, 600}, {260, 289} }, |
| {2, {1755, 1950}, {810, 900}, {390, 433} }, |
| {3, {2340, 2600}, {1080, 1200}, {520, 578} }, |
| {4, {3510, 3900}, {1620, 1800}, {780, 867} }, |
| {5, {4680, 5200}, {2160, 2400}, {1040, 1156} }, |
| {6, {5265, 5850}, {2430, 2700}, {1170, 1300} }, |
| {7, {5850, 6500}, {2700, 3000}, {1300, 1444} }, |
| {8, {7020, 7800}, {3240, 3600}, {1560, 1733} }, |
| {9, {7800, 8667}, {3600, 4000}, {1560, 1733} } |
| }; |
| |
| static void ath10k_mac_get_rate_flags_ht(struct ath10k *ar, u32 rate, u8 nss, u8 mcs, |
| u8 *flags, u8 *bw) |
| { |
| struct ath10k_index_ht_data_rate_type *mcs_rate; |
| u8 index; |
| size_t len_nss1 = ARRAY_SIZE(supported_ht_mcs_rate_nss1); |
| size_t len_nss2 = ARRAY_SIZE(supported_ht_mcs_rate_nss2); |
| |
| if (mcs >= (len_nss1 + len_nss2)) { |
| ath10k_warn(ar, "not supported mcs %d in current rate table", mcs); |
| return; |
| } |
| |
| mcs_rate = (struct ath10k_index_ht_data_rate_type *) |
| ((nss == 1) ? &supported_ht_mcs_rate_nss1 : |
| &supported_ht_mcs_rate_nss2); |
| |
| if (mcs >= len_nss1) |
| index = mcs - len_nss1; |
| else |
| index = mcs; |
| |
| if (rate == mcs_rate[index].supported_rate[0]) { |
| *bw = RATE_INFO_BW_20; |
| } else if (rate == mcs_rate[index].supported_rate[1]) { |
| *bw |= RATE_INFO_BW_40; |
| } else if (rate == mcs_rate[index].supported_rate[2]) { |
| *bw |= RATE_INFO_BW_20; |
| *flags |= RATE_INFO_FLAGS_SHORT_GI; |
| } else if (rate == mcs_rate[index].supported_rate[3]) { |
| *bw |= RATE_INFO_BW_40; |
| *flags |= RATE_INFO_FLAGS_SHORT_GI; |
| } else { |
| ath10k_warn(ar, "invalid ht params rate %d 100kbps nss %d mcs %d", |
| rate, nss, mcs); |
| } |
| } |
| |
| static void ath10k_mac_get_rate_flags_vht(struct ath10k *ar, u32 rate, u8 nss, u8 mcs, |
| u8 *flags, u8 *bw) |
| { |
| struct ath10k_index_vht_data_rate_type *mcs_rate; |
| |
| mcs_rate = (struct ath10k_index_vht_data_rate_type *) |
| ((nss == 1) ? &supported_vht_mcs_rate_nss1 : |
| &supported_vht_mcs_rate_nss2); |
| |
| if (rate == mcs_rate[mcs].supported_VHT80_rate[0]) { |
| *bw = RATE_INFO_BW_80; |
| } else if (rate == mcs_rate[mcs].supported_VHT80_rate[1]) { |
| *bw = RATE_INFO_BW_80; |
| *flags |= RATE_INFO_FLAGS_SHORT_GI; |
| } else if (rate == mcs_rate[mcs].supported_VHT40_rate[0]) { |
| *bw = RATE_INFO_BW_40; |
| } else if (rate == mcs_rate[mcs].supported_VHT40_rate[1]) { |
| *bw = RATE_INFO_BW_40; |
| *flags |= RATE_INFO_FLAGS_SHORT_GI; |
| } else if (rate == mcs_rate[mcs].supported_VHT20_rate[0]) { |
| *bw = RATE_INFO_BW_20; |
| } else if (rate == mcs_rate[mcs].supported_VHT20_rate[1]) { |
| *bw = RATE_INFO_BW_20; |
| *flags |= RATE_INFO_FLAGS_SHORT_GI; |
| } else { |
| ath10k_warn(ar, "invalid vht params rate %d 100kbps nss %d mcs %d", |
| rate, nss, mcs); |
| } |
| } |
| |
| static void ath10k_mac_get_rate_flags(struct ath10k *ar, u32 rate, |
| enum ath10k_phy_mode mode, u8 nss, u8 mcs, |
| u8 *flags, u8 *bw) |
| { |
| if (mode == ATH10K_PHY_MODE_HT) { |
| *flags = RATE_INFO_FLAGS_MCS; |
| ath10k_mac_get_rate_flags_ht(ar, rate, nss, mcs, flags, bw); |
| } else if (mode == ATH10K_PHY_MODE_VHT) { |
| *flags = RATE_INFO_FLAGS_VHT_MCS; |
| ath10k_mac_get_rate_flags_vht(ar, rate, nss, mcs, flags, bw); |
| } |
| } |
| |
| static void ath10k_mac_parse_bitrate(struct ath10k *ar, u32 rate_code, |
| u32 bitrate_kbps, struct rate_info *rate) |
| { |
| enum ath10k_phy_mode mode = ATH10K_PHY_MODE_LEGACY; |
| enum wmi_rate_preamble preamble = WMI_TLV_GET_HW_RC_PREAM_V1(rate_code); |
| u8 nss = WMI_TLV_GET_HW_RC_NSS_V1(rate_code) + 1; |
| u8 mcs = WMI_TLV_GET_HW_RC_RATE_V1(rate_code); |
| u8 flags = 0, bw = 0; |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, "mac parse rate code 0x%x bitrate %d kbps\n", |
| rate_code, bitrate_kbps); |
| |
| if (preamble == WMI_RATE_PREAMBLE_HT) |
| mode = ATH10K_PHY_MODE_HT; |
| else if (preamble == WMI_RATE_PREAMBLE_VHT) |
| mode = ATH10K_PHY_MODE_VHT; |
| |
| ath10k_mac_get_rate_flags(ar, bitrate_kbps / 100, mode, nss, mcs, &flags, &bw); |
| |
| ath10k_dbg(ar, ATH10K_DBG_MAC, |
| "mac parse bitrate preamble %d mode %d nss %d mcs %d flags %x bw %d\n", |
| preamble, mode, nss, mcs, flags, bw); |
| |
| rate->flags = flags; |
| rate->bw = bw; |
| rate->legacy = bitrate_kbps / 100; |
| rate->nss = nss; |
| rate->mcs = mcs; |
| } |
| |
| static void ath10k_mac_sta_get_peer_stats_info(struct ath10k *ar, |
| struct ieee80211_sta *sta, |
| struct station_info *sinfo) |
| { |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k_peer *peer; |
| unsigned long time_left; |
| int ret; |
| |
| if (!(ar->hw_params.supports_peer_stats_info && |
| arsta->arvif->vdev_type == WMI_VDEV_TYPE_STA)) |
| return; |
| |
| spin_lock_bh(&ar->data_lock); |
| peer = ath10k_peer_find(ar, arsta->arvif->vdev_id, sta->addr); |
| spin_unlock_bh(&ar->data_lock); |
| if (!peer) |
| return; |
| |
| reinit_completion(&ar->peer_stats_info_complete); |
| |
| ret = ath10k_wmi_request_peer_stats_info(ar, |
| arsta->arvif->vdev_id, |
| WMI_REQUEST_ONE_PEER_STATS_INFO, |
| arsta->arvif->bssid, |
| 0); |
| if (ret && ret != -EOPNOTSUPP) { |
| ath10k_warn(ar, "could not request peer stats info: %d\n", ret); |
| return; |
| } |
| |
| time_left = wait_for_completion_timeout(&ar->peer_stats_info_complete, 3 * HZ); |
| if (time_left == 0) { |
| ath10k_warn(ar, "timed out waiting peer stats info\n"); |
| return; |
| } |
| |
| if (arsta->rx_rate_code != 0 && arsta->rx_bitrate_kbps != 0) { |
| ath10k_mac_parse_bitrate(ar, arsta->rx_rate_code, |
| arsta->rx_bitrate_kbps, |
| &sinfo->rxrate); |
| |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_RX_BITRATE); |
| arsta->rx_rate_code = 0; |
| arsta->rx_bitrate_kbps = 0; |
| } |
| |
| if (arsta->tx_rate_code != 0 && arsta->tx_bitrate_kbps != 0) { |
| ath10k_mac_parse_bitrate(ar, arsta->tx_rate_code, |
| arsta->tx_bitrate_kbps, |
| &sinfo->txrate); |
| |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_BITRATE); |
| arsta->tx_rate_code = 0; |
| arsta->tx_bitrate_kbps = 0; |
| } |
| } |
| |
| static void ath10k_sta_statistics(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct station_info *sinfo) |
| { |
| struct ath10k_sta *arsta = (struct ath10k_sta *)sta->drv_priv; |
| struct ath10k *ar = arsta->arvif->ar; |
| |
| if (!ath10k_peer_stats_enabled(ar)) |
| return; |
| |
| mutex_lock(&ar->conf_mutex); |
| ath10k_debug_fw_stats_request(ar); |
| mutex_unlock(&ar->conf_mutex); |
| |
| sinfo->rx_duration = arsta->rx_duration; |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_RX_DURATION); |
| |
| if (arsta->txrate.legacy || arsta->txrate.nss) { |
| if (arsta->txrate.legacy) { |
| sinfo->txrate.legacy = arsta->txrate.legacy; |
| } else { |
| sinfo->txrate.mcs = arsta->txrate.mcs; |
| sinfo->txrate.nss = arsta->txrate.nss; |
| sinfo->txrate.bw = arsta->txrate.bw; |
| } |
| sinfo->txrate.flags = arsta->txrate.flags; |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_BITRATE); |
| } |
| |
| if (ar->htt.disable_tx_comp) { |
| sinfo->tx_failed = arsta->tx_failed; |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_FAILED); |
| } |
| |
| sinfo->tx_retries = arsta->tx_retries; |
| sinfo->filled |= BIT_ULL(NL80211_STA_INFO_TX_RETRIES); |
| |
| ath10k_mac_sta_get_peer_stats_info(ar, sta, sinfo); |
| } |
| |
| static int ath10k_mac_op_set_tid_config(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| struct cfg80211_tid_config *tid_config) |
| { |
| struct ath10k *ar = hw->priv; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_mac_iter_tid_conf_data data = {}; |
| struct wmi_per_peer_per_tid_cfg_arg arg = {}; |
| int ret, i; |
| |
| mutex_lock(&ar->conf_mutex); |
| arg.vdev_id = arvif->vdev_id; |
| |
| arvif->tids_rst = 0; |
| memset(arvif->tid_conf_changed, 0, sizeof(arvif->tid_conf_changed)); |
| |
| for (i = 0; i < tid_config->n_tid_conf; i++) { |
| ret = ath10k_mac_parse_tid_config(ar, sta, vif, |
| &tid_config->tid_conf[i], |
| &arg); |
| if (ret) |
| goto exit; |
| } |
| |
| ret = 0; |
| |
| if (sta) |
| goto exit; |
| |
| arvif->tids_rst = 0; |
| data.curr_vif = vif; |
| data.ar = ar; |
| |
| ieee80211_iterate_stations_atomic(hw, ath10k_mac_vif_stations_tid_conf, |
| &data); |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static int ath10k_mac_op_reset_tid_config(struct ieee80211_hw *hw, |
| struct ieee80211_vif *vif, |
| struct ieee80211_sta *sta, |
| u8 tids) |
| { |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| struct ath10k_mac_iter_tid_conf_data data = {}; |
| struct ath10k *ar = hw->priv; |
| int ret = 0; |
| |
| mutex_lock(&ar->conf_mutex); |
| |
| if (sta) { |
| arvif->tids_rst = 0; |
| ret = ath10k_mac_reset_tid_config(ar, sta, arvif, tids); |
| goto exit; |
| } |
| |
| arvif->tids_rst = tids; |
| data.curr_vif = vif; |
| data.ar = ar; |
| ieee80211_iterate_stations_atomic(hw, ath10k_mac_vif_stations_tid_conf, |
| &data); |
| |
| exit: |
| mutex_unlock(&ar->conf_mutex); |
| return ret; |
| } |
| |
| static const struct ieee80211_ops ath10k_ops = { |
| .tx = ath10k_mac_op_tx, |
| .wake_tx_queue = ath10k_mac_op_wake_tx_queue, |
| .start = ath10k_start, |
| .stop = ath10k_stop, |
| .config = ath10k_config, |
| .add_interface = ath10k_add_interface, |
| .update_vif_offload = ath10k_update_vif_offload, |
| .remove_interface = ath10k_remove_interface, |
| .configure_filter = ath10k_configure_filter, |
| .bss_info_changed = ath10k_bss_info_changed, |
| .set_coverage_class = ath10k_mac_op_set_coverage_class, |
| .hw_scan = ath10k_hw_scan, |
| .cancel_hw_scan = ath10k_cancel_hw_scan, |
| .set_key = ath10k_set_key, |
| .set_default_unicast_key = ath10k_set_default_unicast_key, |
| .sta_state = ath10k_sta_state, |
| .sta_set_txpwr = ath10k_sta_set_txpwr, |
| .conf_tx = ath10k_conf_tx, |
| .remain_on_channel = ath10k_remain_on_channel, |
| .cancel_remain_on_channel = ath10k_cancel_remain_on_channel, |
| .set_rts_threshold = ath10k_set_rts_threshold, |
| .set_frag_threshold = ath10k_mac_op_set_frag_threshold, |
| .flush = ath10k_flush, |
| .tx_last_beacon = ath10k_tx_last_beacon, |
| .set_antenna = ath10k_set_antenna, |
| .get_antenna = ath10k_get_antenna, |
| .reconfig_complete = ath10k_reconfig_complete, |
| .get_survey = ath10k_get_survey, |
| .set_bitrate_mask = ath10k_mac_op_set_bitrate_mask, |
| .sta_rc_update = ath10k_sta_rc_update, |
| .offset_tsf = ath10k_offset_tsf, |
| .ampdu_action = ath10k_ampdu_action, |
| .get_et_sset_count = ath10k_debug_get_et_sset_count, |
| .get_et_stats = ath10k_debug_get_et_stats, |
| .get_et_strings = ath10k_debug_get_et_strings, |
| .add_chanctx = ath10k_mac_op_add_chanctx, |
| .remove_chanctx = ath10k_mac_op_remove_chanctx, |
| .change_chanctx = ath10k_mac_op_change_chanctx, |
| .assign_vif_chanctx = ath10k_mac_op_assign_vif_chanctx, |
| .unassign_vif_chanctx = ath10k_mac_op_unassign_vif_chanctx, |
| .switch_vif_chanctx = ath10k_mac_op_switch_vif_chanctx, |
| .sta_pre_rcu_remove = ath10k_mac_op_sta_pre_rcu_remove, |
| .sta_statistics = ath10k_sta_statistics, |
| .set_tid_config = ath10k_mac_op_set_tid_config, |
| .reset_tid_config = ath10k_mac_op_reset_tid_config, |
| |
| CFG80211_TESTMODE_CMD(ath10k_tm_cmd) |
| |
| #ifdef CONFIG_PM |
| .suspend = ath10k_wow_op_suspend, |
| .resume = ath10k_wow_op_resume, |
| .set_wakeup = ath10k_wow_op_set_wakeup, |
| #endif |
| #ifdef CONFIG_MAC80211_DEBUGFS |
| .sta_add_debugfs = ath10k_sta_add_debugfs, |
| #endif |
| .set_sar_specs = ath10k_mac_set_sar_specs, |
| }; |
| |
| #define CHAN2G(_channel, _freq, _flags) { \ |
| .band = NL80211_BAND_2GHZ, \ |
| .hw_value = (_channel), \ |
| .center_freq = (_freq), \ |
| .flags = (_flags), \ |
| .max_antenna_gain = 0, \ |
| .max_power = 30, \ |
| } |
| |
| #define CHAN5G(_channel, _freq, _flags) { \ |
| .band = NL80211_BAND_5GHZ, \ |
| .hw_value = (_channel), \ |
| .center_freq = (_freq), \ |
| .flags = (_flags), \ |
| .max_antenna_gain = 0, \ |
| .max_power = 30, \ |
| } |
| |
| static const struct ieee80211_channel ath10k_2ghz_channels[] = { |
| CHAN2G(1, 2412, 0), |
| CHAN2G(2, 2417, 0), |
| CHAN2G(3, 2422, 0), |
| CHAN2G(4, 2427, 0), |
| CHAN2G(5, 2432, 0), |
| CHAN2G(6, 2437, 0), |
| CHAN2G(7, 2442, 0), |
| CHAN2G(8, 2447, 0), |
| CHAN2G(9, 2452, 0), |
| CHAN2G(10, 2457, 0), |
| CHAN2G(11, 2462, 0), |
| CHAN2G(12, 2467, 0), |
| CHAN2G(13, 2472, 0), |
| CHAN2G(14, 2484, 0), |
| }; |
| |
| static const struct ieee80211_channel ath10k_5ghz_channels[] = { |
| CHAN5G(36, 5180, 0), |
| CHAN5G(40, 5200, 0), |
| CHAN5G(44, 5220, 0), |
| CHAN5G(48, 5240, 0), |
| CHAN5G(52, 5260, 0), |
| CHAN5G(56, 5280, 0), |
| CHAN5G(60, 5300, 0), |
| CHAN5G(64, 5320, 0), |
| CHAN5G(100, 5500, 0), |
| CHAN5G(104, 5520, 0), |
| CHAN5G(108, 5540, 0), |
| CHAN5G(112, 5560, 0), |
| CHAN5G(116, 5580, 0), |
| CHAN5G(120, 5600, 0), |
| CHAN5G(124, 5620, 0), |
| CHAN5G(128, 5640, 0), |
| CHAN5G(132, 5660, 0), |
| CHAN5G(136, 5680, 0), |
| CHAN5G(140, 5700, 0), |
| CHAN5G(144, 5720, 0), |
| CHAN5G(149, 5745, 0), |
| CHAN5G(153, 5765, 0), |
| CHAN5G(157, 5785, 0), |
| CHAN5G(161, 5805, 0), |
| CHAN5G(165, 5825, 0), |
| CHAN5G(169, 5845, 0), |
| CHAN5G(173, 5865, 0), |
| /* If you add more, you may need to change ATH10K_MAX_5G_CHAN */ |
| /* And you will definitely need to change ATH10K_NUM_CHANS in core.h */ |
| }; |
| |
| struct ath10k *ath10k_mac_create(size_t priv_size) |
| { |
| struct ieee80211_hw *hw; |
| struct ieee80211_ops *ops; |
| struct ath10k *ar; |
| |
| ops = kmemdup(&ath10k_ops, sizeof(ath10k_ops), GFP_KERNEL); |
| if (!ops) |
| return NULL; |
| |
| hw = ieee80211_alloc_hw(sizeof(struct ath10k) + priv_size, ops); |
| if (!hw) { |
| kfree(ops); |
| return NULL; |
| } |
| |
| ar = hw->priv; |
| ar->hw = hw; |
| ar->ops = ops; |
| |
| return ar; |
| } |
| |
| void ath10k_mac_destroy(struct ath10k *ar) |
| { |
| struct ieee80211_ops *ops = ar->ops; |
| |
| ieee80211_free_hw(ar->hw); |
| kfree(ops); |
| } |
| |
| static const struct ieee80211_iface_limit ath10k_if_limits[] = { |
| { |
| .max = 8, |
| .types = BIT(NL80211_IFTYPE_STATION) |
| | BIT(NL80211_IFTYPE_P2P_CLIENT) |
| }, |
| { |
| .max = 3, |
| .types = BIT(NL80211_IFTYPE_P2P_GO) |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_P2P_DEVICE) |
| }, |
| { |
| .max = 7, |
| .types = BIT(NL80211_IFTYPE_AP) |
| #ifdef CONFIG_MAC80211_MESH |
| | BIT(NL80211_IFTYPE_MESH_POINT) |
| #endif |
| }, |
| }; |
| |
| static const struct ieee80211_iface_limit ath10k_10x_if_limits[] = { |
| { |
| .max = 8, |
| .types = BIT(NL80211_IFTYPE_AP) |
| #ifdef CONFIG_MAC80211_MESH |
| | BIT(NL80211_IFTYPE_MESH_POINT) |
| #endif |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_STATION) |
| }, |
| }; |
| |
| static const struct ieee80211_iface_combination ath10k_if_comb[] = { |
| { |
| .limits = ath10k_if_limits, |
| .n_limits = ARRAY_SIZE(ath10k_if_limits), |
| .max_interfaces = 8, |
| .num_different_channels = 1, |
| .beacon_int_infra_match = true, |
| }, |
| }; |
| |
| static const struct ieee80211_iface_combination ath10k_10x_if_comb[] = { |
| { |
| .limits = ath10k_10x_if_limits, |
| .n_limits = ARRAY_SIZE(ath10k_10x_if_limits), |
| .max_interfaces = 8, |
| .num_different_channels = 1, |
| .beacon_int_infra_match = true, |
| .beacon_int_min_gcd = 1, |
| #ifdef CONFIG_ATH10K_DFS_CERTIFIED |
| .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | |
| BIT(NL80211_CHAN_WIDTH_20) | |
| BIT(NL80211_CHAN_WIDTH_40) | |
| BIT(NL80211_CHAN_WIDTH_80), |
| #endif |
| }, |
| }; |
| |
| static const struct ieee80211_iface_limit ath10k_tlv_if_limit[] = { |
| { |
| .max = 2, |
| .types = BIT(NL80211_IFTYPE_STATION), |
| }, |
| { |
| .max = 2, |
| .types = BIT(NL80211_IFTYPE_AP) | |
| #ifdef CONFIG_MAC80211_MESH |
| BIT(NL80211_IFTYPE_MESH_POINT) | |
| #endif |
| BIT(NL80211_IFTYPE_P2P_CLIENT) | |
| BIT(NL80211_IFTYPE_P2P_GO), |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_P2P_DEVICE), |
| }, |
| }; |
| |
| static const struct ieee80211_iface_limit ath10k_tlv_qcs_if_limit[] = { |
| { |
| .max = 2, |
| .types = BIT(NL80211_IFTYPE_STATION), |
| }, |
| { |
| .max = 2, |
| .types = BIT(NL80211_IFTYPE_P2P_CLIENT), |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_AP) | |
| #ifdef CONFIG_MAC80211_MESH |
| BIT(NL80211_IFTYPE_MESH_POINT) | |
| #endif |
| BIT(NL80211_IFTYPE_P2P_GO), |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_P2P_DEVICE), |
| }, |
| }; |
| |
| static const struct ieee80211_iface_limit ath10k_tlv_if_limit_ibss[] = { |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_STATION), |
| }, |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_ADHOC), |
| }, |
| }; |
| |
| /* FIXME: This is not thoroughly tested. These combinations may over- or |
| * underestimate hw/fw capabilities. |
| */ |
| static struct ieee80211_iface_combination ath10k_tlv_if_comb[] = { |
| { |
| .limits = ath10k_tlv_if_limit, |
| .num_different_channels = 1, |
| .max_interfaces = 4, |
| .n_limits = ARRAY_SIZE(ath10k_tlv_if_limit), |
| }, |
| { |
| .limits = ath10k_tlv_if_limit_ibss, |
| .num_different_channels = 1, |
| .max_interfaces = 2, |
| .n_limits = ARRAY_SIZE(ath10k_tlv_if_limit_ibss), |
| }, |
| }; |
| |
| static struct ieee80211_iface_combination ath10k_tlv_qcs_if_comb[] = { |
| { |
| .limits = ath10k_tlv_if_limit, |
| .num_different_channels = 1, |
| .max_interfaces = 4, |
| .n_limits = ARRAY_SIZE(ath10k_tlv_if_limit), |
| }, |
| { |
| .limits = ath10k_tlv_qcs_if_limit, |
| .num_different_channels = 2, |
| .max_interfaces = 4, |
| .n_limits = ARRAY_SIZE(ath10k_tlv_qcs_if_limit), |
| }, |
| { |
| .limits = ath10k_tlv_if_limit_ibss, |
| .num_different_channels = 1, |
| .max_interfaces = 2, |
| .n_limits = ARRAY_SIZE(ath10k_tlv_if_limit_ibss), |
| }, |
| }; |
| |
| static const struct ieee80211_iface_limit ath10k_10_4_if_limits[] = { |
| { |
| .max = 1, |
| .types = BIT(NL80211_IFTYPE_STATION), |
| }, |
| { |
| .max = 16, |
| .types = BIT(NL80211_IFTYPE_AP) |
| #ifdef CONFIG_MAC80211_MESH |
| | BIT(NL80211_IFTYPE_MESH_POINT) |
| #endif |
| }, |
| }; |
| |
| static const struct ieee80211_iface_combination ath10k_10_4_if_comb[] = { |
| { |
| .limits = ath10k_10_4_if_limits, |
| .n_limits = ARRAY_SIZE(ath10k_10_4_if_limits), |
| .max_interfaces = 16, |
| .num_different_channels = 1, |
| .beacon_int_infra_match = true, |
| .beacon_int_min_gcd = 1, |
| #ifdef CONFIG_ATH10K_DFS_CERTIFIED |
| .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | |
| BIT(NL80211_CHAN_WIDTH_20) | |
| BIT(NL80211_CHAN_WIDTH_40) | |
| BIT(NL80211_CHAN_WIDTH_80) | |
| BIT(NL80211_CHAN_WIDTH_80P80) | |
| BIT(NL80211_CHAN_WIDTH_160), |
| #endif |
| }, |
| }; |
| |
| static const struct |
| ieee80211_iface_combination ath10k_10_4_bcn_int_if_comb[] = { |
| { |
| .limits = ath10k_10_4_if_limits, |
| .n_limits = ARRAY_SIZE(ath10k_10_4_if_limits), |
| .max_interfaces = 16, |
| .num_different_channels = 1, |
| .beacon_int_infra_match = true, |
| .beacon_int_min_gcd = 100, |
| #ifdef CONFIG_ATH10K_DFS_CERTIFIED |
| .radar_detect_widths = BIT(NL80211_CHAN_WIDTH_20_NOHT) | |
| BIT(NL80211_CHAN_WIDTH_20) | |
| BIT(NL80211_CHAN_WIDTH_40) | |
| BIT(NL80211_CHAN_WIDTH_80) | |
| BIT(NL80211_CHAN_WIDTH_80P80) | |
| BIT(NL80211_CHAN_WIDTH_160), |
| #endif |
| }, |
| }; |
| |
| static void ath10k_get_arvif_iter(void *data, u8 *mac, |
| struct ieee80211_vif *vif) |
| { |
| struct ath10k_vif_iter *arvif_iter = data; |
| struct ath10k_vif *arvif = (void *)vif->drv_priv; |
| |
| if (arvif->vdev_id == arvif_iter->vdev_id) |
| arvif_iter->arvif = arvif; |
| } |
| |
| struct ath10k_vif *ath10k_get_arvif(struct ath10k *ar, u32 vdev_id) |
| { |
| struct ath10k_vif_iter arvif_iter; |
| |
| memset(&arvif_iter, 0, sizeof(struct ath10k_vif_iter)); |
| arvif_iter.vdev_id = vdev_id; |
| |
| ieee80211_iterate_active_interfaces_atomic(ar->hw, |
| ATH10K_ITER_RESUME_FLAGS, |
| ath10k_get_arvif_iter, |
| &arvif_iter); |
| if (!arvif_iter.arvif) { |
| ath10k_warn(ar, "No VIF found for vdev %d\n", vdev_id); |
| return NULL; |
| } |
| |
| return arvif_iter.arvif; |
| } |
| |
| #define WRD_METHOD "WRDD" |
| #define WRDD_WIFI (0x07) |
| |
| static u32 ath10k_mac_wrdd_get_mcc(struct ath10k *ar, union acpi_object *wrdd) |
| { |
| union acpi_object *mcc_pkg; |
| union acpi_object *domain_type; |
| union acpi_object *mcc_value; |
| u32 i; |
| |
| if (wrdd->type != ACPI_TYPE_PACKAGE || |
| wrdd->package.count < 2 || |
| wrdd->package.elements[0].type != ACPI_TYPE_INTEGER || |
| wrdd->package.elements[0].integer.value != 0) { |
| ath10k_warn(ar, "ignoring malformed/unsupported wrdd structure\n"); |
| return 0; |
| } |
| |
| for (i = 1; i < wrdd->package.count; ++i) { |
| mcc_pkg = &wrdd->package.elements[i]; |
| |
| if (mcc_pkg->type != ACPI_TYPE_PACKAGE) |
| continue; |
| if (mcc_pkg->package.count < 2) |
| continue; |
| if (mcc_pkg->package.elements[0].type != ACPI_TYPE_INTEGER || |
| mcc_pkg->package.elements[1].type != ACPI_TYPE_INTEGER) |
| continue; |
| |
| domain_type = &mcc_pkg->package.elements[0]; |
| if (domain_type->integer.value != WRDD_WIFI) |
| continue; |
| |
| mcc_value = &mcc_pkg->package.elements[1]; |
| return mcc_value->integer.value; |
| } |
| return 0; |
| } |
| |
| static int ath10k_mac_get_wrdd_regulatory(struct ath10k *ar, u16 *rd) |
| { |
| acpi_handle root_handle; |
| acpi_handle handle; |
| struct acpi_buffer wrdd = {ACPI_ALLOCATE_BUFFER, NULL}; |
| acpi_status status; |
| u32 alpha2_code; |
| char alpha2[3]; |
| |
| root_handle = ACPI_HANDLE(ar->dev); |
| if (!root_handle) |
| return -EOPNOTSUPP; |
| |
| status = acpi_get_handle(root_handle, (acpi_string)WRD_METHOD, &handle); |
| if (ACPI_FAILURE(status)) { |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, |
| "failed to get wrd method %d\n", status); |
| return -EIO; |
| } |
| |
| status = acpi_evaluate_object(handle, NULL, NULL, &wrdd); |
| if (ACPI_FAILURE(status)) { |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, |
| "failed to call wrdc %d\n", status); |
| return -EIO; |
| } |
| |
| alpha2_code = ath10k_mac_wrdd_get_mcc(ar, wrdd.pointer); |
| kfree(wrdd.pointer); |
| if (!alpha2_code) |
| return -EIO; |
| |
| alpha2[0] = (alpha2_code >> 8) & 0xff; |
| alpha2[1] = (alpha2_code >> 0) & 0xff; |
| alpha2[2] = '\0'; |
| |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, |
| "regulatory hint from WRDD (alpha2-code): %s\n", alpha2); |
| |
| *rd = ath_regd_find_country_by_name(alpha2); |
| if (*rd == 0xffff) |
| return -EIO; |
| |
| *rd |= COUNTRY_ERD_FLAG; |
| return 0; |
| } |
| |
| static int ath10k_mac_init_rd(struct ath10k *ar) |
| { |
| int ret; |
| u16 rd; |
| |
| ret = ath10k_mac_get_wrdd_regulatory(ar, &rd); |
| if (ret) { |
| ath10k_dbg(ar, ATH10K_DBG_BOOT, |
| "fallback to eeprom programmed regulatory settings\n"); |
| rd = ar->hw_eeprom_rd; |
| } |
| |
| ar->ath_common.regulatory.current_rd = rd; |
| return 0; |
| } |
| |
| int ath10k_mac_register(struct ath10k *ar) |
| { |
| static const u32 cipher_suites[] = { |
| WLAN_CIPHER_SUITE_WEP40, |
| WLAN_CIPHER_SUITE_WEP104, |
| WLAN_CIPHER_SUITE_TKIP, |
| WLAN_CIPHER_SUITE_CCMP, |
| |
| /* Do not add hardware supported ciphers before this line. |
| * Allow software encryption for all chips. Don't forget to |
| * update n_cipher_suites below. |
| */ |
| WLAN_CIPHER_SUITE_AES_CMAC, |
| WLAN_CIPHER_SUITE_BIP_CMAC_256, |
| WLAN_CIPHER_SUITE_BIP_GMAC_128, |
| WLAN_CIPHER_SUITE_BIP_GMAC_256, |
| |
| /* Only QCA99x0 and QCA4019 variants support GCMP-128, GCMP-256 |
| * and CCMP-256 in hardware. |
| */ |
| WLAN_CIPHER_SUITE_GCMP, |
| WLAN_CIPHER_SUITE_GCMP_256, |
| WLAN_CIPHER_SUITE_CCMP_256, |
| }; |
| struct ieee80211_supported_band *band; |
| void *channels; |
| int ret; |
| |
| if (!is_valid_ether_addr(ar->mac_addr)) { |
| ath10k_warn(ar, "invalid MAC address; choosing random\n"); |
| eth_random_addr(ar->mac_addr); |
| } |
| SET_IEEE80211_PERM_ADDR(ar->hw, ar->mac_addr); |
| |
| SET_IEEE80211_DEV(ar->hw, ar->dev); |
| |
| BUILD_BUG_ON((ARRAY_SIZE(ath10k_2ghz_channels) + |
| ARRAY_SIZE(ath10k_5ghz_channels)) != |
| ATH10K_NUM_CHANS); |
| |
| if (ar->phy_capability & WHAL_WLAN_11G_CAPABILITY) { |
| channels = kmemdup(ath10k_2ghz_channels, |
| sizeof(ath10k_2ghz_channels), |
| GFP_KERNEL); |
| if (!channels) { |
| ret = -ENOMEM; |
| goto err_free; |
| } |
| |
| band = &ar->mac.sbands[NL80211_BAND_2GHZ]; |
| band->n_channels = ARRAY_SIZE(ath10k_2ghz_channels); |
| band->channels = channels; |
| |
| if (ar->hw_params.cck_rate_map_rev2) { |
| band->n_bitrates = ath10k_g_rates_rev2_size; |
| band->bitrates = ath10k_g_rates_rev2; |
| } else { |
| band->n_bitrates = ath10k_g_rates_size; |
| band->bitrates = ath10k_g_rates; |
| } |
| |
| ar->hw->wiphy->bands[NL80211_BAND_2GHZ] = band; |
| } |
| |
| if (ar->phy_capability & WHAL_WLAN_11A_CAPABILITY) { |
| channels = kmemdup(ath10k_5ghz_channels, |
| sizeof(ath10k_5ghz_channels), |
| GFP_KERNEL); |
| if (!channels) { |
| ret = -ENOMEM; |
| goto err_free; |
| } |
| |
| band = &ar->mac.sbands[NL80211_BAND_5GHZ]; |
| band->n_channels = ARRAY_SIZE(ath10k_5ghz_channels); |
| band->channels = channels; |
| band->n_bitrates = ath10k_a_rates_size; |
| band->bitrates = ath10k_a_rates; |
| ar->hw->wiphy->bands[NL80211_BAND_5GHZ] = band; |
| } |
| |
| wiphy_read_of_freq_limits(ar->hw->wiphy); |
| ath10k_mac_setup_ht_vht_cap(ar); |
| |
| ar->hw->wiphy->interface_modes = |
| BIT(NL80211_IFTYPE_STATION) | |
| BIT(NL80211_IFTYPE_AP) | |
| BIT(NL80211_IFTYPE_MESH_POINT); |
| |
| ar->hw->wiphy->available_antennas_rx = ar->cfg_rx_chainmask; |
| ar->hw->wiphy->available_antennas_tx = ar->cfg_tx_chainmask; |
| |
| if (!test_bit(ATH10K_FW_FEATURE_NO_P2P, ar->normal_mode_fw.fw_file.fw_features)) |
| ar->hw->wiphy->interface_modes |= |
| BIT(NL80211_IFTYPE_P2P_DEVICE) | |
| BIT(NL80211_IFTYPE_P2P_CLIENT) | |
| BIT(NL80211_IFTYPE_P2P_GO); |
| |
| ieee80211_hw_set(ar->hw, SIGNAL_DBM); |
| |
| if (!test_bit(ATH10K_FW_FEATURE_NO_PS, |
| ar->running_fw->fw_file.fw_features)) { |
| ieee80211_hw_set(ar->hw, SUPPORTS_PS); |
| ieee80211_hw_set(ar->hw, SUPPORTS_DYNAMIC_PS); |
| } |
| |
| ieee80211_hw_set(ar->hw, MFP_CAPABLE); |
| ieee80211_hw_set(ar->hw, REPORTS_TX_ACK_STATUS); |
| ieee80211_hw_set(ar->hw, HAS_RATE_CONTROL); |
| ieee80211_hw_set(ar->hw, AP_LINK_PS); |
| ieee80211_hw_set(ar->hw, SPECTRUM_MGMT); |
| ieee80211_hw_set(ar->hw, SUPPORT_FAST_XMIT); |
| ieee80211_hw_set(ar->hw, CONNECTION_MONITOR); |
| ieee80211_hw_set(ar->hw, SUPPORTS_PER_STA_GTK); |
| ieee80211_hw_set(ar->hw, WANT_MONITOR_VIF); |
| ieee80211_hw_set(ar->hw, CHANCTX_STA_CSA); |
| ieee80211_hw_set(ar->hw, QUEUE_CONTROL); |
| ieee80211_hw_set(ar->hw, SUPPORTS_TX_FRAG); |
| ieee80211_hw_set(ar->hw, REPORTS_LOW_ACK); |
| |
| if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) |
| ieee80211_hw_set(ar->hw, SW_CRYPTO_CONTROL); |
| |
| ar->hw->wiphy->features |= NL80211_FEATURE_STATIC_SMPS; |
| ar->hw->wiphy->flags |= WIPHY_FLAG_IBSS_RSN; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_DYNAMIC_SMPS) |
| ar->hw->wiphy->features |= NL80211_FEATURE_DYNAMIC_SMPS; |
| |
| if (ar->ht_cap_info & WMI_HT_CAP_ENABLED) { |
| ieee80211_hw_set(ar->hw, AMPDU_AGGREGATION); |
| ieee80211_hw_set(ar->hw, TX_AMPDU_SETUP_IN_HW); |
| } |
| |
| ar->hw->wiphy->max_scan_ssids = WLAN_SCAN_PARAMS_MAX_SSID; |
| ar->hw->wiphy->max_scan_ie_len = WLAN_SCAN_PARAMS_MAX_IE_LEN; |
| |
| if (test_bit(WMI_SERVICE_NLO, ar->wmi.svc_map)) { |
| ar->hw->wiphy->max_sched_scan_ssids = WMI_PNO_MAX_SUPP_NETWORKS; |
| ar->hw->wiphy->max_match_sets = WMI_PNO_MAX_SUPP_NETWORKS; |
| ar->hw->wiphy->max_sched_scan_ie_len = WMI_PNO_MAX_IE_LENGTH; |
| ar->hw->wiphy->max_sched_scan_plans = WMI_PNO_MAX_SCHED_SCAN_PLANS; |
| ar->hw->wiphy->max_sched_scan_plan_interval = |
| WMI_PNO_MAX_SCHED_SCAN_PLAN_INT; |
| ar->hw->wiphy->max_sched_scan_plan_iterations = |
| WMI_PNO_MAX_SCHED_SCAN_PLAN_ITRNS; |
| ar->hw->wiphy->features |= NL80211_FEATURE_ND_RANDOM_MAC_ADDR; |
| } |
| |
| ar->hw->vif_data_size = sizeof(struct ath10k_vif); |
| ar->hw->sta_data_size = sizeof(struct ath10k_sta); |
| ar->hw->txq_data_size = sizeof(struct ath10k_txq); |
| |
| ar->hw->max_listen_interval = ATH10K_MAX_HW_LISTEN_INTERVAL; |
| |
| if (test_bit(WMI_SERVICE_BEACON_OFFLOAD, ar->wmi.svc_map)) { |
| ar->hw->wiphy->flags |= WIPHY_FLAG_AP_PROBE_RESP_OFFLOAD; |
| |
| /* Firmware delivers WPS/P2P Probe Requests frames to driver so |
| * that userspace (e.g. wpa_supplicant/hostapd) can generate |
| * correct Probe Responses. This is more of a hack advert.. |
| */ |
| ar->hw->wiphy->probe_resp_offload |= |
| NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS | |
| NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 | |
| NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P; |
| } |
| |
| if (test_bit(WMI_SERVICE_TDLS, ar->wmi.svc_map) || |
| test_bit(WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY, ar->wmi.svc_map)) { |
| ar->hw->wiphy->flags |= WIPHY_FLAG_SUPPORTS_TDLS; |
| if (test_bit(WMI_SERVICE_TDLS_WIDER_BANDWIDTH, ar->wmi.svc_map)) |
| ieee80211_hw_set(ar->hw, TDLS_WIDER_BW); |
| } |
| |
| if (test_bit(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, ar->wmi.svc_map)) |
| ieee80211_hw_set(ar->hw, SUPPORTS_TDLS_BUFFER_STA); |
| |
| if (ath10k_frame_mode == ATH10K_HW_TXRX_ETHERNET) { |
| if (ar->wmi.vdev_param->tx_encap_type != |
| WMI_VDEV_PARAM_UNSUPPORTED) |
| ieee80211_hw_set(ar->hw, SUPPORTS_TX_ENCAP_OFFLOAD); |
| } |
| |
| ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL; |
| ar->hw->wiphy->flags |= WIPHY_FLAG_HAS_CHANNEL_SWITCH; |
| ar->hw->wiphy->max_remain_on_channel_duration = 5000; |
| |
| ar->hw->wiphy->flags |= WIPHY_FLAG_AP_UAPSD; |
| ar->hw->wiphy->features |= NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE | |
| NL80211_FEATURE_AP_SCAN; |
| |
| ar->hw->wiphy->max_ap_assoc_sta = ar->max_num_stations; |
| |
| ret = ath10k_wow_init(ar); |
| if (ret) { |
| ath10k_warn(ar, "failed to init wow: %d\n", ret); |
| goto err_free; |
| } |
| |
| wiphy_ext_feature_set(ar->hw->wiphy, NL80211_EXT_FEATURE_VHT_IBSS); |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_SET_SCAN_DWELL); |
| wiphy_ext_feature_set(ar->hw->wiphy, NL80211_EXT_FEATURE_AQL); |
| |
| if (ar->hw_params.mcast_frame_registration) |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_MULTICAST_REGISTRATIONS); |
| |
| if (test_bit(WMI_SERVICE_TX_DATA_ACK_RSSI, ar->wmi.svc_map) || |
| test_bit(WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, ar->wmi.svc_map)) |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT); |
| |
| if (ath10k_peer_stats_enabled(ar) || |
| test_bit(WMI_SERVICE_REPORT_AIRTIME, ar->wmi.svc_map)) |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_AIRTIME_FAIRNESS); |
| |
| if (test_bit(WMI_SERVICE_RTT_RESPONDER_ROLE, ar->wmi.svc_map)) |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER); |
| |
| if (test_bit(WMI_SERVICE_TX_PWR_PER_PEER, ar->wmi.svc_map)) |
| wiphy_ext_feature_set(ar->hw->wiphy, |
| NL80211_EXT_FEATURE_STA_TX_PWR); |
| |
| if (test_bit(WMI_SERVICE_PEER_TID_CONFIGS_SUPPORT, ar->wmi.svc_map)) { |
| ar->hw->wiphy->tid_config_support.vif |= |
| BIT(NL80211_TID_CONFIG_ATTR_NOACK) | |
| BIT(NL80211_TID_CONFIG_ATTR_RETRY_SHORT) | |
| BIT(NL80211_TID_CONFIG_ATTR_RETRY_LONG) | |
| BIT(NL80211_TID_CONFIG_ATTR_AMPDU_CTRL) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE) | |
| BIT(NL80211_TID_CONFIG_ATTR_TX_RATE_TYPE); |
| |
| if (test_bit(WMI_SERVICE_EXT_PEER_TID_CONFIGS_SUPPORT, |
| ar->wmi.svc_map)) { |
| ar->hw->wiphy->tid_config_support.vif |= |
| BIT(NL80211_TID_CONFIG_ATTR_RTSCTS_CTRL); |
| } |
| |
| ar->hw->wiphy->tid_config_support.peer = |
| ar->hw->wiphy->tid_config_support.vif; |
| ar->hw->wiphy->max_data_retry_count = ATH10K_MAX_RETRY_COUNT; |
| } else { |
| ar->ops->set_tid_config = NULL; |
| } |
| /* |
| * on LL hardware queues are managed entirely by the FW |
| * so we only advertise to mac we can do the queues thing |
| */ |
| ar->hw->queues = IEEE80211_MAX_QUEUES; |
| |
| /* vdev_ids are used as hw queue numbers. Make sure offchan tx queue is |
| * something that vdev_ids can't reach so that we don't stop the queue |
| * accidentally. |
| */ |
| ar->hw->offchannel_tx_hw_queue = IEEE80211_MAX_QUEUES - 1; |
| |
| switch (ar->running_fw->fw_file.wmi_op_version) { |
| case ATH10K_FW_WMI_OP_VERSION_MAIN: |
| ar->hw->wiphy->iface_combinations = ath10k_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_if_comb); |
| ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC); |
| break; |
| case ATH10K_FW_WMI_OP_VERSION_TLV: |
| if (test_bit(WMI_SERVICE_ADAPTIVE_OCS, ar->wmi.svc_map)) { |
| ar->hw->wiphy->iface_combinations = |
| ath10k_tlv_qcs_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_tlv_qcs_if_comb); |
| } else { |
| ar->hw->wiphy->iface_combinations = ath10k_tlv_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_tlv_if_comb); |
| } |
| ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_ADHOC); |
| break; |
| case ATH10K_FW_WMI_OP_VERSION_10_1: |
| case ATH10K_FW_WMI_OP_VERSION_10_2: |
| case ATH10K_FW_WMI_OP_VERSION_10_2_4: |
| ar->hw->wiphy->iface_combinations = ath10k_10x_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_10x_if_comb); |
| break; |
| case ATH10K_FW_WMI_OP_VERSION_10_4: |
| ar->hw->wiphy->iface_combinations = ath10k_10_4_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_10_4_if_comb); |
| if (test_bit(WMI_SERVICE_VDEV_DIFFERENT_BEACON_INTERVAL_SUPPORT, |
| ar->wmi.svc_map)) { |
| ar->hw->wiphy->iface_combinations = |
| ath10k_10_4_bcn_int_if_comb; |
| ar->hw->wiphy->n_iface_combinations = |
| ARRAY_SIZE(ath10k_10_4_bcn_int_if_comb); |
| } |
| break; |
| case ATH10K_FW_WMI_OP_VERSION_UNSET: |
| case ATH10K_FW_WMI_OP_VERSION_MAX: |
| WARN_ON(1); |
| ret = -EINVAL; |
| goto err_free; |
| } |
| |
| if (ar->hw_params.dynamic_sar_support) |
| ar->hw->wiphy->sar_capa = &ath10k_sar_capa; |
| |
| if (!test_bit(ATH10K_FLAG_RAW_MODE, &ar->dev_flags)) |
| ar->hw->netdev_features = NETIF_F_HW_CSUM; |
| |
| if (IS_ENABLED(CONFIG_ATH10K_DFS_CERTIFIED)) { |
| /* Init ath dfs pattern detector */ |
| ar->ath_common.debug_mask = ATH_DBG_DFS; |
| ar->dfs_detector = dfs_pattern_detector_init(&ar->ath_common, |
| NL80211_DFS_UNSET); |
| |
| if (!ar->dfs_detector) |
| ath10k_warn(ar, "failed to initialise DFS pattern detector\n"); |
| } |
| |
| ret = ath10k_mac_init_rd(ar); |
| if (ret) { |
| ath10k_err(ar, "failed to derive regdom: %d\n", ret); |
| goto err_dfs_detector_exit; |
| } |
| |
| /* Disable set_coverage_class for chipsets that do not support it. */ |
| if (!ar->hw_params.hw_ops->set_coverage_class) |
| ar->ops->set_coverage_class = NULL; |
| |
| ret = ath_regd_init(&ar->ath_common.regulatory, ar->hw->wiphy, |
| ath10k_reg_notifier); |
| if (ret) { |
| ath10k_err(ar, "failed to initialise regulatory: %i\n", ret); |
| goto err_dfs_detector_exit; |
| } |
| |
| if (test_bit(WMI_SERVICE_SPOOF_MAC_SUPPORT, ar->wmi.svc_map)) { |
| ar->hw->wiphy->features |= |
| NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR; |
| } |
| |
| ar->hw->wiphy->cipher_suites = cipher_suites; |
| |
| /* QCA988x and QCA6174 family chips do not support CCMP-256, GCMP-128 |
| * and GCMP-256 ciphers in hardware. Fetch number of ciphers supported |
| * from chip specific hw_param table. |
| */ |
| if (!ar->hw_params.n_cipher_suites || |
| ar->hw_params.n_cipher_suites > ARRAY_SIZE(cipher_suites)) { |
| ath10k_err(ar, "invalid hw_params.n_cipher_suites %d\n", |
| ar->hw_params.n_cipher_suites); |
| ar->hw_params.n_cipher_suites = 8; |
| } |
| ar->hw->wiphy->n_cipher_suites = ar->hw_params.n_cipher_suites; |
| |
| wiphy_ext_feature_set(ar->hw->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| |
| ar->hw->weight_multiplier = ATH10K_AIRTIME_WEIGHT_MULTIPLIER; |
| |
| ret = ieee80211_register_hw(ar->hw); |
| if (ret) { |
| ath10k_err(ar, "failed to register ieee80211: %d\n", ret); |
| goto err_dfs_detector_exit; |
| } |
| |
| if (test_bit(WMI_SERVICE_PER_PACKET_SW_ENCRYPT, ar->wmi.svc_map)) { |
| ar->hw->wiphy->interface_modes |= BIT(NL80211_IFTYPE_AP_VLAN); |
| ar->hw->wiphy->software_iftypes |= BIT(NL80211_IFTYPE_AP_VLAN); |
| } |
| |
| if (!ath_is_world_regd(&ar->ath_common.reg_world_copy) && |
| !ath_is_world_regd(&ar->ath_common.regulatory)) { |
| ret = regulatory_hint(ar->hw->wiphy, |
| ar->ath_common.regulatory.alpha2); |
| if (ret) |
| goto err_unregister; |
| } |
| |
| return 0; |
| |
| err_unregister: |
| ieee80211_unregister_hw(ar->hw); |
| |
| err_dfs_detector_exit: |
| if (IS_ENABLED(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) |
| ar->dfs_detector->exit(ar->dfs_detector); |
| |
| err_free: |
| kfree(ar->mac.sbands[NL80211_BAND_2GHZ].channels); |
| kfree(ar->mac.sbands[NL80211_BAND_5GHZ].channels); |
| |
| SET_IEEE80211_DEV(ar->hw, NULL); |
| return ret; |
| } |
| |
| void ath10k_mac_unregister(struct ath10k *ar) |
| { |
| ieee80211_unregister_hw(ar->hw); |
| |
| if (IS_ENABLED(CONFIG_ATH10K_DFS_CERTIFIED) && ar->dfs_detector) |
| ar->dfs_detector->exit(ar->dfs_detector); |
| |
| kfree(ar->mac.sbands[NL80211_BAND_2GHZ].channels); |
| kfree(ar->mac.sbands[NL80211_BAND_5GHZ].channels); |
| |
| SET_IEEE80211_DEV(ar->hw, NULL); |
| } |