| // SPDX-License-Identifier: GPL-2.0 |
| /* Copyright(c) 2007 - 2011 Realtek Corporation. */ |
| |
| #define _HAL_INIT_C_ |
| |
| #include "../include/linux/firmware.h" |
| #include "../include/drv_types.h" |
| #include "../include/rtw_efuse.h" |
| #include "../include/rtl8188e_hal.h" |
| #include "../include/rtw_iol.h" |
| #include "../include/usb_ops.h" |
| |
| static void iol_mode_enable(struct adapter *padapter, u8 enable) |
| { |
| u8 reg_0xf0 = 0; |
| |
| if (enable) { |
| /* Enable initial offload */ |
| reg_0xf0 = rtw_read8(padapter, REG_SYS_CFG); |
| rtw_write8(padapter, REG_SYS_CFG, reg_0xf0 | SW_OFFLOAD_EN); |
| |
| if (!padapter->bFWReady) { |
| DBG_88E("bFWReady == false call reset 8051...\n"); |
| _8051Reset88E(padapter); |
| } |
| |
| } else { |
| /* disable initial offload */ |
| reg_0xf0 = rtw_read8(padapter, REG_SYS_CFG); |
| rtw_write8(padapter, REG_SYS_CFG, reg_0xf0 & ~SW_OFFLOAD_EN); |
| } |
| } |
| |
| static s32 iol_execute(struct adapter *padapter, u8 control) |
| { |
| s32 status = _FAIL; |
| u8 reg_0x88 = 0; |
| u32 start = 0, passing_time = 0; |
| |
| control = control & 0x0f; |
| reg_0x88 = rtw_read8(padapter, REG_HMEBOX_E0); |
| rtw_write8(padapter, REG_HMEBOX_E0, reg_0x88 | control); |
| |
| start = jiffies; |
| while ((reg_0x88 = rtw_read8(padapter, REG_HMEBOX_E0)) & control && |
| (passing_time = rtw_get_passing_time_ms(start)) < 1000) { |
| ; |
| } |
| |
| reg_0x88 = rtw_read8(padapter, REG_HMEBOX_E0); |
| status = (reg_0x88 & control) ? _FAIL : _SUCCESS; |
| if (reg_0x88 & control << 4) |
| status = _FAIL; |
| return status; |
| } |
| |
| static s32 iol_InitLLTTable(struct adapter *padapter, u8 txpktbuf_bndy) |
| { |
| s32 rst = _SUCCESS; |
| iol_mode_enable(padapter, 1); |
| rtw_write8(padapter, REG_TDECTRL + 1, txpktbuf_bndy); |
| rst = iol_execute(padapter, CMD_INIT_LLT); |
| iol_mode_enable(padapter, 0); |
| return rst; |
| } |
| |
| static void |
| efuse_phymap_to_logical(u8 *phymap, u16 _offset, u16 _size_byte, u8 *pbuf) |
| { |
| u8 *efuseTbl = NULL; |
| u8 rtemp8; |
| u16 eFuse_Addr = 0; |
| u8 offset, wren; |
| u16 i, j; |
| u16 **eFuseWord = NULL; |
| u16 efuse_utilized = 0; |
| u8 u1temp = 0; |
| |
| efuseTbl = kzalloc(EFUSE_MAP_LEN_88E, GFP_KERNEL); |
| if (!efuseTbl) { |
| DBG_88E("%s: alloc efuseTbl fail!\n", __func__); |
| goto exit; |
| } |
| |
| eFuseWord = rtw_malloc2d(EFUSE_MAX_SECTION_88E, EFUSE_MAX_WORD_UNIT, sizeof(u16)); |
| if (!eFuseWord) { |
| DBG_88E("%s: alloc eFuseWord fail!\n", __func__); |
| goto exit; |
| } |
| |
| /* 0. Refresh efuse init map as all oxFF. */ |
| for (i = 0; i < EFUSE_MAX_SECTION_88E; i++) |
| for (j = 0; j < EFUSE_MAX_WORD_UNIT; j++) |
| eFuseWord[i][j] = 0xFFFF; |
| |
| /* */ |
| /* 1. Read the first byte to check if efuse is empty!!! */ |
| /* */ |
| /* */ |
| rtemp8 = *(phymap + eFuse_Addr); |
| if (rtemp8 != 0xFF) { |
| efuse_utilized++; |
| eFuse_Addr++; |
| } else { |
| DBG_88E("EFUSE is empty efuse_Addr-%d efuse_data =%x\n", eFuse_Addr, rtemp8); |
| goto exit; |
| } |
| |
| /* */ |
| /* 2. Read real efuse content. Filter PG header and every section data. */ |
| /* */ |
| while ((rtemp8 != 0xFF) && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) { |
| /* Check PG header for section num. */ |
| if ((rtemp8 & 0x1F) == 0x0F) { /* extended header */ |
| u1temp = ((rtemp8 & 0xE0) >> 5); |
| rtemp8 = *(phymap + eFuse_Addr); |
| if ((rtemp8 & 0x0F) == 0x0F) { |
| eFuse_Addr++; |
| rtemp8 = *(phymap + eFuse_Addr); |
| |
| if (rtemp8 != 0xFF && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) |
| eFuse_Addr++; |
| continue; |
| } else { |
| offset = ((rtemp8 & 0xF0) >> 1) | u1temp; |
| wren = (rtemp8 & 0x0F); |
| eFuse_Addr++; |
| } |
| } else { |
| offset = ((rtemp8 >> 4) & 0x0f); |
| wren = (rtemp8 & 0x0f); |
| } |
| |
| if (offset < EFUSE_MAX_SECTION_88E) { |
| /* Get word enable value from PG header */ |
| for (i = 0; i < EFUSE_MAX_WORD_UNIT; i++) { |
| /* Check word enable condition in the section */ |
| if (!(wren & 0x01)) { |
| rtemp8 = *(phymap + eFuse_Addr); |
| eFuse_Addr++; |
| efuse_utilized++; |
| eFuseWord[offset][i] = (rtemp8 & 0xff); |
| if (eFuse_Addr >= EFUSE_REAL_CONTENT_LEN_88E) |
| break; |
| rtemp8 = *(phymap + eFuse_Addr); |
| eFuse_Addr++; |
| efuse_utilized++; |
| eFuseWord[offset][i] |= (((u16)rtemp8 << 8) & 0xff00); |
| |
| if (eFuse_Addr >= EFUSE_REAL_CONTENT_LEN_88E) |
| break; |
| } |
| wren >>= 1; |
| } |
| } |
| /* Read next PG header */ |
| rtemp8 = *(phymap + eFuse_Addr); |
| |
| if (rtemp8 != 0xFF && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) { |
| efuse_utilized++; |
| eFuse_Addr++; |
| } |
| } |
| |
| /* */ |
| /* 3. Collect 16 sections and 4 word unit into Efuse map. */ |
| /* */ |
| for (i = 0; i < EFUSE_MAX_SECTION_88E; i++) { |
| for (j = 0; j < EFUSE_MAX_WORD_UNIT; j++) { |
| efuseTbl[(i * 8) + (j * 2)] = (eFuseWord[i][j] & 0xff); |
| efuseTbl[(i * 8) + ((j * 2) + 1)] = ((eFuseWord[i][j] >> 8) & 0xff); |
| } |
| } |
| |
| /* */ |
| /* 4. Copy from Efuse map to output pointer memory!!! */ |
| /* */ |
| for (i = 0; i < _size_byte; i++) |
| pbuf[i] = efuseTbl[_offset + i]; |
| |
| /* */ |
| /* 5. Calculate Efuse utilization. */ |
| /* */ |
| |
| exit: |
| kfree(efuseTbl); |
| kfree(eFuseWord); |
| } |
| |
| static void efuse_read_phymap_from_txpktbuf( |
| struct adapter *adapter, |
| int bcnhead, /* beacon head, where FW store len(2-byte) and efuse physical map. */ |
| u8 *content, /* buffer to store efuse physical map */ |
| u16 *size /* for efuse content: the max byte to read. will update to byte read */ |
| ) |
| { |
| u16 dbg_addr = 0; |
| u32 start = 0, passing_time = 0; |
| u8 reg_0x143 = 0; |
| __le32 lo32 = 0, hi32 = 0; |
| u16 len = 0, count = 0; |
| int i = 0; |
| u16 limit = *size; |
| |
| u8 *pos = content; |
| |
| if (bcnhead < 0) /* if not valid */ |
| bcnhead = rtw_read8(adapter, REG_TDECTRL + 1); |
| |
| DBG_88E("%s bcnhead:%d\n", __func__, bcnhead); |
| |
| rtw_write8(adapter, REG_PKT_BUFF_ACCESS_CTRL, TXPKT_BUF_SELECT); |
| |
| dbg_addr = bcnhead * 128 / 8; /* 8-bytes addressing */ |
| |
| while (1) { |
| rtw_write16(adapter, REG_PKTBUF_DBG_ADDR, dbg_addr + i); |
| |
| rtw_write8(adapter, REG_TXPKTBUF_DBG, 0); |
| start = jiffies; |
| while (!(reg_0x143 = rtw_read8(adapter, REG_TXPKTBUF_DBG)) && |
| (passing_time = rtw_get_passing_time_ms(start)) < 1000) { |
| DBG_88E("%s polling reg_0x143:0x%02x, reg_0x106:0x%02x\n", __func__, reg_0x143, rtw_read8(adapter, 0x106)); |
| rtw_usleep_os(100); |
| } |
| |
| /* data from EEPROM needs to be in LE */ |
| lo32 = cpu_to_le32(rtw_read32(adapter, REG_PKTBUF_DBG_DATA_L)); |
| hi32 = cpu_to_le32(rtw_read32(adapter, REG_PKTBUF_DBG_DATA_H)); |
| |
| if (i == 0) { |
| /* Although lenc is only used in a debug statement, |
| * do not remove it as the rtw_read16() call consumes |
| * 2 bytes from the EEPROM source. |
| */ |
| u16 lenc = rtw_read16(adapter, REG_PKTBUF_DBG_DATA_L); |
| |
| len = le32_to_cpu(lo32) & 0x0000ffff; |
| |
| limit = (len - 2 < limit) ? len - 2 : limit; |
| |
| DBG_88E("%s len:%u, lenc:%u\n", __func__, len, lenc); |
| |
| memcpy(pos, ((u8 *)&lo32) + 2, (limit >= count + 2) ? 2 : limit - count); |
| count += (limit >= count + 2) ? 2 : limit - count; |
| pos = content + count; |
| } else { |
| memcpy(pos, ((u8 *)&lo32), (limit >= count + 4) ? 4 : limit - count); |
| count += (limit >= count + 4) ? 4 : limit - count; |
| pos = content + count; |
| } |
| |
| if (limit > count && len - 2 > count) { |
| memcpy(pos, (u8 *)&hi32, (limit >= count + 4) ? 4 : limit - count); |
| count += (limit >= count + 4) ? 4 : limit - count; |
| pos = content + count; |
| } |
| |
| if (limit <= count || len - 2 <= count) |
| break; |
| i++; |
| } |
| rtw_write8(adapter, REG_PKT_BUFF_ACCESS_CTRL, DISABLE_TRXPKT_BUF_ACCESS); |
| DBG_88E("%s read count:%u\n", __func__, count); |
| *size = count; |
| } |
| |
| static s32 iol_read_efuse(struct adapter *padapter, u8 txpktbuf_bndy, u16 offset, u16 size_byte, u8 *logical_map) |
| { |
| s32 status = _FAIL; |
| u8 physical_map[512]; |
| u16 size = 512; |
| |
| rtw_write8(padapter, REG_TDECTRL + 1, txpktbuf_bndy); |
| memset(physical_map, 0xFF, 512); |
| rtw_write8(padapter, REG_PKT_BUFF_ACCESS_CTRL, TXPKT_BUF_SELECT); |
| status = iol_execute(padapter, CMD_READ_EFUSE_MAP); |
| if (status == _SUCCESS) |
| efuse_read_phymap_from_txpktbuf(padapter, txpktbuf_bndy, physical_map, &size); |
| efuse_phymap_to_logical(physical_map, offset, size_byte, logical_map); |
| return status; |
| } |
| |
| s32 rtl8188e_iol_efuse_patch(struct adapter *padapter) |
| { |
| s32 result = _SUCCESS; |
| |
| DBG_88E("==> %s\n", __func__); |
| if (rtw_IOL_applied(padapter)) { |
| iol_mode_enable(padapter, 1); |
| result = iol_execute(padapter, CMD_READ_EFUSE_MAP); |
| if (result == _SUCCESS) |
| result = iol_execute(padapter, CMD_EFUSE_PATCH); |
| |
| iol_mode_enable(padapter, 0); |
| } |
| return result; |
| } |
| |
| static s32 iol_ioconfig(struct adapter *padapter, u8 iocfg_bndy) |
| { |
| s32 rst = _SUCCESS; |
| |
| rtw_write8(padapter, REG_TDECTRL + 1, iocfg_bndy); |
| rst = iol_execute(padapter, CMD_IOCONFIG); |
| return rst; |
| } |
| |
| int rtl8188e_IOL_exec_cmds_sync(struct adapter *adapter, struct xmit_frame *xmit_frame, u32 max_wating_ms, u32 bndy_cnt) |
| { |
| struct pkt_attrib *pattrib = &xmit_frame->attrib; |
| u8 i; |
| int ret = _FAIL; |
| |
| if (rtw_IOL_append_END_cmd(xmit_frame) != _SUCCESS) |
| goto exit; |
| if (rtw_usb_bulk_size_boundary(adapter, TXDESC_SIZE + pattrib->last_txcmdsz)) { |
| if (rtw_IOL_append_END_cmd(xmit_frame) != _SUCCESS) |
| goto exit; |
| } |
| |
| dump_mgntframe_and_wait(adapter, xmit_frame, max_wating_ms); |
| |
| iol_mode_enable(adapter, 1); |
| for (i = 0; i < bndy_cnt; i++) { |
| u8 page_no = 0; |
| page_no = i * 2; |
| ret = iol_ioconfig(adapter, page_no); |
| if (ret != _SUCCESS) |
| break; |
| } |
| iol_mode_enable(adapter, 0); |
| exit: |
| /* restore BCN_HEAD */ |
| rtw_write8(adapter, REG_TDECTRL + 1, 0); |
| return ret; |
| } |
| |
| static void _FWDownloadEnable(struct adapter *padapter, bool enable) |
| { |
| u8 tmp; |
| |
| if (enable) { |
| /* MCU firmware download enable. */ |
| tmp = rtw_read8(padapter, REG_MCUFWDL); |
| rtw_write8(padapter, REG_MCUFWDL, tmp | 0x01); |
| |
| /* 8051 reset */ |
| tmp = rtw_read8(padapter, REG_MCUFWDL + 2); |
| rtw_write8(padapter, REG_MCUFWDL + 2, tmp & 0xf7); |
| } else { |
| /* MCU firmware download disable. */ |
| tmp = rtw_read8(padapter, REG_MCUFWDL); |
| rtw_write8(padapter, REG_MCUFWDL, tmp & 0xfe); |
| |
| /* Reserved for fw extension. */ |
| rtw_write8(padapter, REG_MCUFWDL + 1, 0x00); |
| } |
| } |
| |
| #define MAX_REG_BOLCK_SIZE 196 |
| |
| static int _BlockWrite(struct adapter *padapter, void *buffer, u32 buffSize) |
| { |
| int ret = _SUCCESS; |
| u32 blockSize_p1 = 4; /* (Default) Phase #1 : PCI muse use 4-byte write to download FW */ |
| u32 blockSize_p2 = 8; /* Phase #2 : Use 8-byte, if Phase#1 use big size to write FW. */ |
| u32 blockSize_p3 = 1; /* Phase #3 : Use 1-byte, the remnant of FW image. */ |
| u32 blockCount_p1 = 0, blockCount_p2 = 0, blockCount_p3 = 0; |
| u32 remainSize_p1 = 0, remainSize_p2 = 0; |
| u8 *bufferPtr = (u8 *)buffer; |
| u32 i = 0, offset = 0; |
| |
| blockSize_p1 = MAX_REG_BOLCK_SIZE; |
| |
| /* 3 Phase #1 */ |
| blockCount_p1 = buffSize / blockSize_p1; |
| remainSize_p1 = buffSize % blockSize_p1; |
| |
| for (i = 0; i < blockCount_p1; i++) { |
| ret = rtw_writeN(padapter, (FW_8188E_START_ADDRESS + i * blockSize_p1), blockSize_p1, (bufferPtr + i * blockSize_p1)); |
| if (ret == _FAIL) |
| goto exit; |
| } |
| |
| /* 3 Phase #2 */ |
| if (remainSize_p1) { |
| offset = blockCount_p1 * blockSize_p1; |
| |
| blockCount_p2 = remainSize_p1 / blockSize_p2; |
| remainSize_p2 = remainSize_p1 % blockSize_p2; |
| |
| for (i = 0; i < blockCount_p2; i++) { |
| ret = rtw_writeN(padapter, (FW_8188E_START_ADDRESS + offset + i * blockSize_p2), blockSize_p2, (bufferPtr + offset + i * blockSize_p2)); |
| |
| if (ret == _FAIL) |
| goto exit; |
| } |
| } |
| |
| /* 3 Phase #3 */ |
| if (remainSize_p2) { |
| offset = (blockCount_p1 * blockSize_p1) + (blockCount_p2 * blockSize_p2); |
| |
| blockCount_p3 = remainSize_p2 / blockSize_p3; |
| |
| for (i = 0; i < blockCount_p3; i++) { |
| ret = rtw_write8(padapter, (FW_8188E_START_ADDRESS + offset + i), *(bufferPtr + offset + i)); |
| |
| if (ret == _FAIL) |
| goto exit; |
| } |
| } |
| |
| exit: |
| return ret; |
| } |
| |
| static int _PageWrite(struct adapter *padapter, u32 page, void *buffer, u32 size) |
| { |
| u8 value8; |
| u8 u8Page = (u8)(page & 0x07); |
| |
| value8 = (rtw_read8(padapter, REG_MCUFWDL + 2) & 0xF8) | u8Page; |
| rtw_write8(padapter, REG_MCUFWDL + 2, value8); |
| |
| return _BlockWrite(padapter, buffer, size); |
| } |
| |
| static int _WriteFW(struct adapter *padapter, void *buffer, u32 size) |
| { |
| /* Since we need dynamic decide method of dwonload fw, so we call this function to get chip version. */ |
| /* We can remove _ReadChipVersion from ReadpadapterInfo8192C later. */ |
| int ret = _SUCCESS; |
| u32 pageNums, remainSize; |
| u32 page, offset; |
| u8 *bufferPtr = (u8 *)buffer; |
| |
| pageNums = size / MAX_PAGE_SIZE; |
| remainSize = size % MAX_PAGE_SIZE; |
| |
| for (page = 0; page < pageNums; page++) { |
| offset = page * MAX_PAGE_SIZE; |
| ret = _PageWrite(padapter, page, bufferPtr + offset, MAX_PAGE_SIZE); |
| |
| if (ret == _FAIL) |
| goto exit; |
| } |
| if (remainSize) { |
| offset = pageNums * MAX_PAGE_SIZE; |
| page = pageNums; |
| ret = _PageWrite(padapter, page, bufferPtr + offset, remainSize); |
| |
| if (ret == _FAIL) |
| goto exit; |
| } |
| exit: |
| return ret; |
| } |
| |
| void _8051Reset88E(struct adapter *padapter) |
| { |
| u8 u1bTmp; |
| |
| u1bTmp = rtw_read8(padapter, REG_SYS_FUNC_EN + 1); |
| rtw_write8(padapter, REG_SYS_FUNC_EN + 1, u1bTmp & (~BIT(2))); |
| rtw_write8(padapter, REG_SYS_FUNC_EN + 1, u1bTmp | (BIT(2))); |
| DBG_88E("=====> _8051Reset88E(): 8051 reset success .\n"); |
| } |
| |
| static s32 _FWFreeToGo(struct adapter *padapter) |
| { |
| u32 counter = 0; |
| u32 value32; |
| |
| /* polling CheckSum report */ |
| do { |
| value32 = rtw_read32(padapter, REG_MCUFWDL); |
| if (value32 & FWDL_ChkSum_rpt) |
| break; |
| } while (counter++ < POLLING_READY_TIMEOUT_COUNT); |
| |
| if (counter >= POLLING_READY_TIMEOUT_COUNT) { |
| DBG_88E("%s: chksum report fail! REG_MCUFWDL:0x%08x\n", __func__, value32); |
| return _FAIL; |
| } |
| DBG_88E("%s: Checksum report OK! REG_MCUFWDL:0x%08x\n", __func__, value32); |
| |
| value32 = rtw_read32(padapter, REG_MCUFWDL); |
| value32 |= MCUFWDL_RDY; |
| value32 &= ~WINTINI_RDY; |
| rtw_write32(padapter, REG_MCUFWDL, value32); |
| |
| _8051Reset88E(padapter); |
| |
| /* polling for FW ready */ |
| counter = 0; |
| do { |
| value32 = rtw_read32(padapter, REG_MCUFWDL); |
| if (value32 & WINTINI_RDY) { |
| DBG_88E("%s: Polling FW ready success!! REG_MCUFWDL:0x%08x\n", __func__, value32); |
| return _SUCCESS; |
| } |
| udelay(5); |
| } while (counter++ < POLLING_READY_TIMEOUT_COUNT); |
| |
| DBG_88E("%s: Polling FW ready fail!! REG_MCUFWDL:0x%08x\n", __func__, value32); |
| return _FAIL; |
| } |
| |
| #define IS_FW_81xxC(padapter) (((GET_HAL_DATA(padapter))->FirmwareSignature & 0xFFF0) == 0x88C0) |
| |
| static int load_firmware(struct rt_firmware *pFirmware, struct device *device) |
| { |
| s32 rtStatus = _SUCCESS; |
| const struct firmware *fw; |
| const char *fw_name = "rtlwifi/rtl8188eufw.bin"; |
| int err = request_firmware(&fw, fw_name, device); |
| |
| if (err) { |
| pr_err("Request firmware failed with error 0x%x\n", err); |
| rtStatus = _FAIL; |
| goto Exit; |
| } |
| if (!fw) { |
| pr_err("Firmware %s not available\n", fw_name); |
| rtStatus = _FAIL; |
| goto Exit; |
| } |
| if (fw->size > FW_8188E_SIZE) { |
| rtStatus = _FAIL; |
| goto Exit; |
| } |
| |
| pFirmware->szFwBuffer = kzalloc(FW_8188E_SIZE, GFP_KERNEL); |
| if (!pFirmware->szFwBuffer) { |
| pr_err("Failed to allocate pFirmware->szFwBuffer\n"); |
| rtStatus = _FAIL; |
| goto Exit; |
| } |
| memcpy(pFirmware->szFwBuffer, fw->data, fw->size); |
| pFirmware->ulFwLength = fw->size; |
| release_firmware(fw); |
| DBG_88E_LEVEL(_drv_info_, "+%s: !bUsedWoWLANFw, FmrmwareLen:%d+\n", __func__, pFirmware->ulFwLength); |
| |
| Exit: |
| return rtStatus; |
| } |
| |
| s32 rtl8188e_FirmwareDownload(struct adapter *padapter) |
| { |
| s32 rtStatus = _SUCCESS; |
| u8 writeFW_retry = 0; |
| u32 fwdl_start_time; |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(padapter); |
| struct dvobj_priv *dvobj = adapter_to_dvobj(padapter); |
| struct device *device = dvobj_to_dev(dvobj); |
| struct rt_firmware_hdr *pFwHdr = NULL; |
| u8 *pFirmwareBuf; |
| u32 FirmwareLen; |
| static int log_version; |
| |
| if (!dvobj->firmware.szFwBuffer) |
| rtStatus = load_firmware(&dvobj->firmware, device); |
| if (rtStatus == _FAIL) { |
| dvobj->firmware.szFwBuffer = NULL; |
| goto Exit; |
| } |
| pFirmwareBuf = dvobj->firmware.szFwBuffer; |
| FirmwareLen = dvobj->firmware.ulFwLength; |
| |
| /* To Check Fw header. Added by tynli. 2009.12.04. */ |
| pFwHdr = (struct rt_firmware_hdr *)dvobj->firmware.szFwBuffer; |
| |
| pHalData->FirmwareVersion = le16_to_cpu(pFwHdr->Version); |
| pHalData->FirmwareSubVersion = pFwHdr->Subversion; |
| pHalData->FirmwareSignature = le16_to_cpu(pFwHdr->Signature); |
| |
| if (!log_version++) |
| pr_info("%sFirmware Version %d, SubVersion %d, Signature 0x%x\n", |
| DRIVER_PREFIX, pHalData->FirmwareVersion, |
| pHalData->FirmwareSubVersion, pHalData->FirmwareSignature); |
| |
| if (IS_FW_HEADER_EXIST(pFwHdr)) { |
| /* Shift 32 bytes for FW header */ |
| pFirmwareBuf = pFirmwareBuf + 32; |
| FirmwareLen = FirmwareLen - 32; |
| } |
| |
| /* Suggested by Filen. If 8051 is running in RAM code, driver should inform Fw to reset by itself, */ |
| /* or it will cause download Fw fail. 2010.02.01. by tynli. */ |
| if (rtw_read8(padapter, REG_MCUFWDL) & RAM_DL_SEL) { /* 8051 RAM code */ |
| rtw_write8(padapter, REG_MCUFWDL, 0x00); |
| _8051Reset88E(padapter); |
| } |
| |
| _FWDownloadEnable(padapter, true); |
| fwdl_start_time = jiffies; |
| while (1) { |
| /* reset the FWDL chksum */ |
| rtw_write8(padapter, REG_MCUFWDL, rtw_read8(padapter, REG_MCUFWDL) | FWDL_ChkSum_rpt); |
| |
| rtStatus = _WriteFW(padapter, pFirmwareBuf, FirmwareLen); |
| |
| if (rtStatus == _SUCCESS || |
| (rtw_get_passing_time_ms(fwdl_start_time) > 500 && writeFW_retry++ >= 3)) |
| break; |
| |
| DBG_88E("%s writeFW_retry:%u, time after fwdl_start_time:%ums\n", |
| __func__, writeFW_retry, rtw_get_passing_time_ms(fwdl_start_time) |
| ); |
| } |
| _FWDownloadEnable(padapter, false); |
| if (_SUCCESS != rtStatus) { |
| DBG_88E("DL Firmware failed!\n"); |
| goto Exit; |
| } |
| |
| rtStatus = _FWFreeToGo(padapter); |
| if (_SUCCESS != rtStatus) { |
| DBG_88E("DL Firmware failed!\n"); |
| goto Exit; |
| } |
| |
| Exit: |
| return rtStatus; |
| } |
| |
| void rtl8188e_InitializeFirmwareVars(struct adapter *padapter) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(padapter); |
| |
| /* Init Fw LPS related. */ |
| padapter->pwrctrlpriv.bFwCurrentInPSMode = false; |
| |
| /* Init H2C counter. by tynli. 2009.12.09. */ |
| pHalData->LastHMEBoxNum = 0; |
| } |
| |
| void rtl8188e_free_hal_data(struct adapter *padapter) |
| { |
| kfree(padapter->HalData); |
| padapter->HalData = NULL; |
| } |
| |
| /* */ |
| /* Efuse related code */ |
| /* */ |
| enum{ |
| VOLTAGE_V25 = 0x03, |
| LDOE25_SHIFT = 28, |
| }; |
| |
| static bool |
| hal_EfusePgPacketWrite2ByteHeader( |
| struct adapter *pAdapter, |
| u8 efuseType, |
| u16 *pAddr, |
| struct pgpkt *pTargetPkt, |
| bool bPseudoTest); |
| static bool |
| hal_EfusePgPacketWrite1ByteHeader( |
| struct adapter *pAdapter, |
| u8 efuseType, |
| u16 *pAddr, |
| struct pgpkt *pTargetPkt, |
| bool bPseudoTest); |
| static bool |
| hal_EfusePgPacketWriteData( |
| struct adapter *pAdapter, |
| u8 efuseType, |
| u16 *pAddr, |
| struct pgpkt *pTargetPkt, |
| bool bPseudoTest); |
| |
| void rtl8188e_EfusePowerSwitch(struct adapter *pAdapter, u8 bWrite, u8 PwrState) |
| { |
| u8 tempval; |
| u16 tmpV16; |
| |
| if (PwrState) { |
| rtw_write8(pAdapter, REG_EFUSE_ACCESS, EFUSE_ACCESS_ON); |
| |
| /* 1.2V Power: From VDDON with Power Cut(0x0000h[15]), defualt valid */ |
| tmpV16 = rtw_read16(pAdapter, REG_SYS_ISO_CTRL); |
| if (!(tmpV16 & PWC_EV12V)) { |
| tmpV16 |= PWC_EV12V; |
| rtw_write16(pAdapter, REG_SYS_ISO_CTRL, tmpV16); |
| } |
| /* Reset: 0x0000h[28], default valid */ |
| tmpV16 = rtw_read16(pAdapter, REG_SYS_FUNC_EN); |
| if (!(tmpV16 & FEN_ELDR)) { |
| tmpV16 |= FEN_ELDR; |
| rtw_write16(pAdapter, REG_SYS_FUNC_EN, tmpV16); |
| } |
| |
| /* Clock: Gated(0x0008h[5]) 8M(0x0008h[1]) clock from ANA, default valid */ |
| tmpV16 = rtw_read16(pAdapter, REG_SYS_CLKR); |
| if ((!(tmpV16 & LOADER_CLK_EN)) || (!(tmpV16 & ANA8M))) { |
| tmpV16 |= (LOADER_CLK_EN | ANA8M); |
| rtw_write16(pAdapter, REG_SYS_CLKR, tmpV16); |
| } |
| |
| if (bWrite) { |
| /* Enable LDO 2.5V before read/write action */ |
| tempval = rtw_read8(pAdapter, EFUSE_TEST + 3); |
| tempval &= 0x0F; |
| tempval |= (VOLTAGE_V25 << 4); |
| rtw_write8(pAdapter, EFUSE_TEST + 3, (tempval | 0x80)); |
| } |
| } else { |
| rtw_write8(pAdapter, REG_EFUSE_ACCESS, EFUSE_ACCESS_OFF); |
| |
| if (bWrite) { |
| /* Disable LDO 2.5V after read/write action */ |
| tempval = rtw_read8(pAdapter, EFUSE_TEST + 3); |
| rtw_write8(pAdapter, EFUSE_TEST + 3, (tempval & 0x7F)); |
| } |
| } |
| } |
| |
| static void Hal_EfuseReadEFuse88E(struct adapter *Adapter, |
| u16 _offset, |
| u16 _size_byte, |
| u8 *pbuf, |
| bool bPseudoTest |
| ) |
| { |
| u8 *efuseTbl = NULL; |
| u8 rtemp8[1]; |
| u16 eFuse_Addr = 0; |
| u8 offset, wren; |
| u16 i, j; |
| u16 **eFuseWord = NULL; |
| u16 efuse_utilized = 0; |
| u8 u1temp = 0; |
| |
| /* */ |
| /* Do NOT excess total size of EFuse table. Added by Roger, 2008.11.10. */ |
| /* */ |
| if ((_offset + _size_byte) > EFUSE_MAP_LEN_88E) {/* total E-Fuse table is 512bytes */ |
| DBG_88E("Hal_EfuseReadEFuse88E(): Invalid offset(%#x) with read bytes(%#x)!!\n", _offset, _size_byte); |
| goto exit; |
| } |
| |
| efuseTbl = kzalloc(EFUSE_MAP_LEN_88E, GFP_KERNEL); |
| if (!efuseTbl) { |
| DBG_88E("%s: alloc efuseTbl fail!\n", __func__); |
| goto exit; |
| } |
| |
| eFuseWord = rtw_malloc2d(EFUSE_MAX_SECTION_88E, EFUSE_MAX_WORD_UNIT, sizeof(u16)); |
| if (!eFuseWord) { |
| DBG_88E("%s: alloc eFuseWord fail!\n", __func__); |
| goto exit; |
| } |
| |
| /* 0. Refresh efuse init map as all oxFF. */ |
| for (i = 0; i < EFUSE_MAX_SECTION_88E; i++) |
| for (j = 0; j < EFUSE_MAX_WORD_UNIT; j++) |
| eFuseWord[i][j] = 0xFFFF; |
| |
| /* */ |
| /* 1. Read the first byte to check if efuse is empty!!! */ |
| /* */ |
| /* */ |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| if (*rtemp8 != 0xFF) { |
| efuse_utilized++; |
| eFuse_Addr++; |
| } else { |
| DBG_88E("EFUSE is empty efuse_Addr-%d efuse_data =%x\n", eFuse_Addr, *rtemp8); |
| goto exit; |
| } |
| |
| /* */ |
| /* 2. Read real efuse content. Filter PG header and every section data. */ |
| /* */ |
| while ((*rtemp8 != 0xFF) && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) { |
| /* Check PG header for section num. */ |
| if ((*rtemp8 & 0x1F) == 0x0F) { /* extended header */ |
| u1temp = ((*rtemp8 & 0xE0) >> 5); |
| |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| |
| if ((*rtemp8 & 0x0F) == 0x0F) { |
| eFuse_Addr++; |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| |
| if (*rtemp8 != 0xFF && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) |
| eFuse_Addr++; |
| continue; |
| } else { |
| offset = ((*rtemp8 & 0xF0) >> 1) | u1temp; |
| wren = (*rtemp8 & 0x0F); |
| eFuse_Addr++; |
| } |
| } else { |
| offset = ((*rtemp8 >> 4) & 0x0f); |
| wren = (*rtemp8 & 0x0f); |
| } |
| |
| if (offset < EFUSE_MAX_SECTION_88E) { |
| /* Get word enable value from PG header */ |
| |
| for (i = 0; i < EFUSE_MAX_WORD_UNIT; i++) { |
| /* Check word enable condition in the section */ |
| if (!(wren & 0x01)) { |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| eFuse_Addr++; |
| efuse_utilized++; |
| eFuseWord[offset][i] = (*rtemp8 & 0xff); |
| if (eFuse_Addr >= EFUSE_REAL_CONTENT_LEN_88E) |
| break; |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| eFuse_Addr++; |
| efuse_utilized++; |
| eFuseWord[offset][i] |= (((u16)*rtemp8 << 8) & 0xff00); |
| if (eFuse_Addr >= EFUSE_REAL_CONTENT_LEN_88E) |
| break; |
| } |
| wren >>= 1; |
| } |
| } |
| |
| /* Read next PG header */ |
| ReadEFuseByte(Adapter, eFuse_Addr, rtemp8, bPseudoTest); |
| |
| if (*rtemp8 != 0xFF && (eFuse_Addr < EFUSE_REAL_CONTENT_LEN_88E)) { |
| efuse_utilized++; |
| eFuse_Addr++; |
| } |
| } |
| |
| /* 3. Collect 16 sections and 4 word unit into Efuse map. */ |
| for (i = 0; i < EFUSE_MAX_SECTION_88E; i++) { |
| for (j = 0; j < EFUSE_MAX_WORD_UNIT; j++) { |
| efuseTbl[(i * 8) + (j * 2)] = (eFuseWord[i][j] & 0xff); |
| efuseTbl[(i * 8) + ((j * 2) + 1)] = ((eFuseWord[i][j] >> 8) & 0xff); |
| } |
| } |
| |
| /* 4. Copy from Efuse map to output pointer memory!!! */ |
| for (i = 0; i < _size_byte; i++) |
| pbuf[i] = efuseTbl[_offset + i]; |
| |
| /* 5. Calculate Efuse utilization. */ |
| SetHwReg8188EU(Adapter, HW_VAR_EFUSE_BYTES, (u8 *)&eFuse_Addr); |
| |
| exit: |
| kfree(efuseTbl); |
| kfree(eFuseWord); |
| } |
| |
| static void ReadEFuseByIC(struct adapter *Adapter, u8 efuseType, u16 _offset, u16 _size_byte, u8 *pbuf, bool bPseudoTest) |
| { |
| if (!bPseudoTest) { |
| int ret = _FAIL; |
| if (rtw_IOL_applied(Adapter)) { |
| rtl8188eu_InitPowerOn(Adapter); |
| |
| iol_mode_enable(Adapter, 1); |
| ret = iol_read_efuse(Adapter, 0, _offset, _size_byte, pbuf); |
| iol_mode_enable(Adapter, 0); |
| |
| if (_SUCCESS == ret) |
| goto exit; |
| } |
| } |
| Hal_EfuseReadEFuse88E(Adapter, _offset, _size_byte, pbuf, bPseudoTest); |
| |
| exit: |
| return; |
| } |
| |
| static void ReadEFuse_Pseudo(struct adapter *Adapter, u8 efuseType, u16 _offset, u16 _size_byte, u8 *pbuf, bool bPseudoTest) |
| { |
| Hal_EfuseReadEFuse88E(Adapter, _offset, _size_byte, pbuf, bPseudoTest); |
| } |
| |
| void rtl8188e_ReadEFuse(struct adapter *Adapter, u8 efuseType, |
| u16 _offset, u16 _size_byte, u8 *pbuf, |
| bool bPseudoTest) |
| { |
| if (bPseudoTest) |
| ReadEFuse_Pseudo(Adapter, efuseType, _offset, _size_byte, pbuf, bPseudoTest); |
| else |
| ReadEFuseByIC(Adapter, efuseType, _offset, _size_byte, pbuf, bPseudoTest); |
| } |
| |
| /* Do not support BT */ |
| static void Hal_EFUSEGetEfuseDefinition88E(struct adapter *pAdapter, u8 efuseType, u8 type, void *pOut) |
| { |
| switch (type) { |
| case TYPE_EFUSE_MAX_SECTION: |
| { |
| u8 *pMax_section; |
| pMax_section = (u8 *)pOut; |
| *pMax_section = EFUSE_MAX_SECTION_88E; |
| } |
| break; |
| case TYPE_EFUSE_REAL_CONTENT_LEN: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = EFUSE_REAL_CONTENT_LEN_88E; |
| } |
| break; |
| case TYPE_EFUSE_CONTENT_LEN_BANK: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = EFUSE_REAL_CONTENT_LEN_88E; |
| } |
| break; |
| case TYPE_AVAILABLE_EFUSE_BYTES_BANK: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)(EFUSE_REAL_CONTENT_LEN_88E - EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| case TYPE_AVAILABLE_EFUSE_BYTES_TOTAL: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)(EFUSE_REAL_CONTENT_LEN_88E - EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| case TYPE_EFUSE_MAP_LEN: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)EFUSE_MAP_LEN_88E; |
| } |
| break; |
| case TYPE_EFUSE_PROTECT_BYTES_BANK: |
| { |
| u8 *pu1Tmp; |
| pu1Tmp = (u8 *)pOut; |
| *pu1Tmp = (u8)(EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| default: |
| { |
| u8 *pu1Tmp; |
| pu1Tmp = (u8 *)pOut; |
| *pu1Tmp = 0; |
| } |
| break; |
| } |
| } |
| |
| static void Hal_EFUSEGetEfuseDefinition_Pseudo88E(struct adapter *pAdapter, u8 efuseType, u8 type, void *pOut) |
| { |
| switch (type) { |
| case TYPE_EFUSE_MAX_SECTION: |
| { |
| u8 *pMax_section; |
| pMax_section = (u8 *)pOut; |
| *pMax_section = EFUSE_MAX_SECTION_88E; |
| } |
| break; |
| case TYPE_EFUSE_REAL_CONTENT_LEN: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = EFUSE_REAL_CONTENT_LEN_88E; |
| } |
| break; |
| case TYPE_EFUSE_CONTENT_LEN_BANK: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = EFUSE_REAL_CONTENT_LEN_88E; |
| } |
| break; |
| case TYPE_AVAILABLE_EFUSE_BYTES_BANK: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)(EFUSE_REAL_CONTENT_LEN_88E - EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| case TYPE_AVAILABLE_EFUSE_BYTES_TOTAL: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)(EFUSE_REAL_CONTENT_LEN_88E - EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| case TYPE_EFUSE_MAP_LEN: |
| { |
| u16 *pu2Tmp; |
| pu2Tmp = (u16 *)pOut; |
| *pu2Tmp = (u16)EFUSE_MAP_LEN_88E; |
| } |
| break; |
| case TYPE_EFUSE_PROTECT_BYTES_BANK: |
| { |
| u8 *pu1Tmp; |
| pu1Tmp = (u8 *)pOut; |
| *pu1Tmp = (u8)(EFUSE_OOB_PROTECT_BYTES_88E); |
| } |
| break; |
| default: |
| { |
| u8 *pu1Tmp; |
| pu1Tmp = (u8 *)pOut; |
| *pu1Tmp = 0; |
| } |
| break; |
| } |
| } |
| |
| void rtl8188e_EFUSE_GetEfuseDefinition(struct adapter *pAdapter, u8 efuseType, u8 type, void *pOut, bool bPseudoTest) |
| { |
| if (bPseudoTest) |
| Hal_EFUSEGetEfuseDefinition_Pseudo88E(pAdapter, efuseType, type, pOut); |
| else |
| Hal_EFUSEGetEfuseDefinition88E(pAdapter, efuseType, type, pOut); |
| } |
| |
| static u8 Hal_EfuseWordEnableDataWrite(struct adapter *pAdapter, u16 efuse_addr, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| u16 tmpaddr = 0; |
| u16 start_addr = efuse_addr; |
| u8 badworden = 0x0F; |
| u8 tmpdata[8]; |
| |
| memset((void *)tmpdata, 0xff, PGPKT_DATA_SIZE); |
| |
| if (!(word_en & BIT(0))) { |
| tmpaddr = start_addr; |
| efuse_OneByteWrite(pAdapter, start_addr++, data[0], bPseudoTest); |
| efuse_OneByteWrite(pAdapter, start_addr++, data[1], bPseudoTest); |
| |
| efuse_OneByteRead(pAdapter, tmpaddr, &tmpdata[0], bPseudoTest); |
| efuse_OneByteRead(pAdapter, tmpaddr + 1, &tmpdata[1], bPseudoTest); |
| if ((data[0] != tmpdata[0]) || (data[1] != tmpdata[1])) |
| badworden &= (~BIT(0)); |
| } |
| if (!(word_en & BIT(1))) { |
| tmpaddr = start_addr; |
| efuse_OneByteWrite(pAdapter, start_addr++, data[2], bPseudoTest); |
| efuse_OneByteWrite(pAdapter, start_addr++, data[3], bPseudoTest); |
| |
| efuse_OneByteRead(pAdapter, tmpaddr, &tmpdata[2], bPseudoTest); |
| efuse_OneByteRead(pAdapter, tmpaddr + 1, &tmpdata[3], bPseudoTest); |
| if ((data[2] != tmpdata[2]) || (data[3] != tmpdata[3])) |
| badworden &= (~BIT(1)); |
| } |
| if (!(word_en & BIT(2))) { |
| tmpaddr = start_addr; |
| efuse_OneByteWrite(pAdapter, start_addr++, data[4], bPseudoTest); |
| efuse_OneByteWrite(pAdapter, start_addr++, data[5], bPseudoTest); |
| |
| efuse_OneByteRead(pAdapter, tmpaddr, &tmpdata[4], bPseudoTest); |
| efuse_OneByteRead(pAdapter, tmpaddr + 1, &tmpdata[5], bPseudoTest); |
| if ((data[4] != tmpdata[4]) || (data[5] != tmpdata[5])) |
| badworden &= (~BIT(2)); |
| } |
| if (!(word_en & BIT(3))) { |
| tmpaddr = start_addr; |
| efuse_OneByteWrite(pAdapter, start_addr++, data[6], bPseudoTest); |
| efuse_OneByteWrite(pAdapter, start_addr++, data[7], bPseudoTest); |
| |
| efuse_OneByteRead(pAdapter, tmpaddr, &tmpdata[6], bPseudoTest); |
| efuse_OneByteRead(pAdapter, tmpaddr + 1, &tmpdata[7], bPseudoTest); |
| if ((data[6] != tmpdata[6]) || (data[7] != tmpdata[7])) |
| badworden &= (~BIT(3)); |
| } |
| return badworden; |
| } |
| |
| static u8 Hal_EfuseWordEnableDataWrite_Pseudo(struct adapter *pAdapter, u16 efuse_addr, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| u8 ret; |
| |
| ret = Hal_EfuseWordEnableDataWrite(pAdapter, efuse_addr, word_en, data, bPseudoTest); |
| return ret; |
| } |
| |
| static u8 rtl8188e_Efuse_WordEnableDataWrite(struct adapter *pAdapter, u16 efuse_addr, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| u8 ret = 0; |
| |
| if (bPseudoTest) |
| ret = Hal_EfuseWordEnableDataWrite_Pseudo(pAdapter, efuse_addr, word_en, data, bPseudoTest); |
| else |
| ret = Hal_EfuseWordEnableDataWrite(pAdapter, efuse_addr, word_en, data, bPseudoTest); |
| return ret; |
| } |
| |
| static u16 hal_EfuseGetCurrentSize_8188e(struct adapter *pAdapter, bool bPseudoTest) |
| { |
| int bContinual = true; |
| u16 efuse_addr = 0; |
| u8 hworden = 0; |
| u8 efuse_data, word_cnts = 0; |
| |
| if (bPseudoTest) |
| efuse_addr = (u16)(fakeEfuseUsedBytes); |
| else |
| GetHwReg8188EU(pAdapter, HW_VAR_EFUSE_BYTES, (u8 *)&efuse_addr); |
| |
| while (bContinual && |
| efuse_OneByteRead(pAdapter, efuse_addr, &efuse_data, bPseudoTest) && |
| AVAILABLE_EFUSE_ADDR(efuse_addr)) { |
| if (efuse_data != 0xFF) { |
| if ((efuse_data & 0x1F) == 0x0F) { /* extended header */ |
| efuse_addr++; |
| efuse_OneByteRead(pAdapter, efuse_addr, &efuse_data, bPseudoTest); |
| if ((efuse_data & 0x0F) == 0x0F) { |
| efuse_addr++; |
| continue; |
| } else { |
| hworden = efuse_data & 0x0F; |
| } |
| } else { |
| hworden = efuse_data & 0x0F; |
| } |
| word_cnts = Efuse_CalculateWordCnts(hworden); |
| /* read next header */ |
| efuse_addr = efuse_addr + (word_cnts * 2) + 1; |
| } else { |
| bContinual = false; |
| } |
| } |
| |
| if (bPseudoTest) |
| fakeEfuseUsedBytes = efuse_addr; |
| else |
| SetHwReg8188EU(pAdapter, HW_VAR_EFUSE_BYTES, (u8 *)&efuse_addr); |
| |
| return efuse_addr; |
| } |
| |
| static u16 Hal_EfuseGetCurrentSize_Pseudo(struct adapter *pAdapter, bool bPseudoTest) |
| { |
| u16 ret = 0; |
| |
| ret = hal_EfuseGetCurrentSize_8188e(pAdapter, bPseudoTest); |
| return ret; |
| } |
| |
| u16 rtl8188e_EfuseGetCurrentSize(struct adapter *pAdapter, u8 efuseType, bool bPseudoTest) |
| { |
| u16 ret = 0; |
| |
| if (bPseudoTest) |
| ret = Hal_EfuseGetCurrentSize_Pseudo(pAdapter, bPseudoTest); |
| else |
| ret = hal_EfuseGetCurrentSize_8188e(pAdapter, bPseudoTest); |
| return ret; |
| } |
| |
| static int hal_EfusePgPacketRead_8188e(struct adapter *pAdapter, u8 offset, u8 *data, bool bPseudoTest) |
| { |
| u8 ReadState = PG_STATE_HEADER; |
| int bContinual = true; |
| int bDataEmpty = true; |
| u8 efuse_data, word_cnts = 0; |
| u16 efuse_addr = 0; |
| u8 hoffset = 0, hworden = 0; |
| u8 tmpidx = 0; |
| u8 tmpdata[8]; |
| u8 max_section = 0; |
| u8 tmp_header = 0; |
| |
| rtl8188e_EFUSE_GetEfuseDefinition(pAdapter, EFUSE_WIFI, TYPE_EFUSE_MAX_SECTION, (void *)&max_section, bPseudoTest); |
| |
| if (!data) |
| return false; |
| if (offset > max_section) |
| return false; |
| |
| memset((void *)data, 0xff, sizeof(u8) * PGPKT_DATA_SIZE); |
| memset((void *)tmpdata, 0xff, sizeof(u8) * PGPKT_DATA_SIZE); |
| |
| /* <Roger_TODO> Efuse has been pre-programmed dummy 5Bytes at the end of Efuse by CP. */ |
| /* Skip dummy parts to prevent unexpected data read from Efuse. */ |
| /* By pass right now. 2009.02.19. */ |
| while (bContinual && AVAILABLE_EFUSE_ADDR(efuse_addr)) { |
| /* Header Read ------------- */ |
| if (ReadState & PG_STATE_HEADER) { |
| if (efuse_OneByteRead(pAdapter, efuse_addr, &efuse_data, bPseudoTest) && (efuse_data != 0xFF)) { |
| if (EXT_HEADER(efuse_data)) { |
| tmp_header = efuse_data; |
| efuse_addr++; |
| efuse_OneByteRead(pAdapter, efuse_addr, &efuse_data, bPseudoTest); |
| if (!ALL_WORDS_DISABLED(efuse_data)) { |
| hoffset = ((tmp_header & 0xE0) >> 5) | ((efuse_data & 0xF0) >> 1); |
| hworden = efuse_data & 0x0F; |
| } else { |
| DBG_88E("Error, All words disabled\n"); |
| efuse_addr++; |
| continue; |
| } |
| } else { |
| hoffset = (efuse_data >> 4) & 0x0F; |
| hworden = efuse_data & 0x0F; |
| } |
| word_cnts = Efuse_CalculateWordCnts(hworden); |
| bDataEmpty = true; |
| |
| if (hoffset == offset) { |
| for (tmpidx = 0; tmpidx < word_cnts * 2; tmpidx++) { |
| if (efuse_OneByteRead(pAdapter, efuse_addr + 1 + tmpidx, &efuse_data, bPseudoTest)) { |
| tmpdata[tmpidx] = efuse_data; |
| if (efuse_data != 0xff) |
| bDataEmpty = false; |
| } |
| } |
| if (!bDataEmpty) { |
| ReadState = PG_STATE_DATA; |
| } else {/* read next header */ |
| efuse_addr = efuse_addr + (word_cnts * 2) + 1; |
| ReadState = PG_STATE_HEADER; |
| } |
| } else {/* read next header */ |
| efuse_addr = efuse_addr + (word_cnts * 2) + 1; |
| ReadState = PG_STATE_HEADER; |
| } |
| } else { |
| bContinual = false; |
| } |
| } else if (ReadState & PG_STATE_DATA) { |
| /* Data section Read ------------- */ |
| efuse_WordEnableDataRead(hworden, tmpdata, data); |
| efuse_addr = efuse_addr + (word_cnts * 2) + 1; |
| ReadState = PG_STATE_HEADER; |
| } |
| |
| } |
| |
| if ((data[0] == 0xff) && (data[1] == 0xff) && (data[2] == 0xff) && (data[3] == 0xff) && |
| (data[4] == 0xff) && (data[5] == 0xff) && (data[6] == 0xff) && (data[7] == 0xff)) |
| return false; |
| else |
| return true; |
| } |
| |
| static int Hal_EfusePgPacketRead(struct adapter *pAdapter, u8 offset, u8 *data, bool bPseudoTest) |
| { |
| int ret; |
| |
| ret = hal_EfusePgPacketRead_8188e(pAdapter, offset, data, bPseudoTest); |
| return ret; |
| } |
| |
| static int Hal_EfusePgPacketRead_Pseudo(struct adapter *pAdapter, u8 offset, u8 *data, bool bPseudoTest) |
| { |
| int ret; |
| |
| ret = hal_EfusePgPacketRead_8188e(pAdapter, offset, data, bPseudoTest); |
| return ret; |
| } |
| |
| int rtl8188e_Efuse_PgPacketRead(struct adapter *pAdapter, u8 offset, u8 *data, bool bPseudoTest) |
| { |
| int ret; |
| |
| if (bPseudoTest) |
| ret = Hal_EfusePgPacketRead_Pseudo(pAdapter, offset, data, bPseudoTest); |
| else |
| ret = Hal_EfusePgPacketRead(pAdapter, offset, data, bPseudoTest); |
| return ret; |
| } |
| |
| static bool hal_EfuseFixHeaderProcess(struct adapter *pAdapter, u8 efuseType, struct pgpkt *pFixPkt, u16 *pAddr, bool bPseudoTest) |
| { |
| u8 originaldata[8], badworden = 0; |
| u16 efuse_addr = *pAddr; |
| u32 PgWriteSuccess = 0; |
| |
| memset((void *)originaldata, 0xff, 8); |
| |
| if (rtl8188e_Efuse_PgPacketRead(pAdapter, pFixPkt->offset, originaldata, bPseudoTest)) { |
| /* check if data exist */ |
| badworden = rtl8188e_Efuse_WordEnableDataWrite(pAdapter, efuse_addr + 1, pFixPkt->word_en, originaldata, bPseudoTest); |
| |
| if (badworden != 0xf) { /* write fail */ |
| PgWriteSuccess = rtl8188e_Efuse_PgPacketWrite(pAdapter, pFixPkt->offset, badworden, originaldata, bPseudoTest); |
| |
| if (!PgWriteSuccess) |
| return false; |
| else |
| efuse_addr = rtl8188e_EfuseGetCurrentSize(pAdapter, efuseType, bPseudoTest); |
| } else { |
| efuse_addr = efuse_addr + (pFixPkt->word_cnts * 2) + 1; |
| } |
| } else { |
| efuse_addr = efuse_addr + (pFixPkt->word_cnts * 2) + 1; |
| } |
| *pAddr = efuse_addr; |
| return true; |
| } |
| |
| static bool hal_EfusePgPacketWrite2ByteHeader(struct adapter *pAdapter, u8 efuseType, u16 *pAddr, struct pgpkt *pTargetPkt, bool bPseudoTest) |
| { |
| bool bRet = false; |
| u16 efuse_addr = *pAddr, efuse_max_available_len = 0; |
| u8 pg_header = 0, tmp_header = 0, pg_header_temp = 0; |
| u8 repeatcnt = 0; |
| |
| rtl8188e_EFUSE_GetEfuseDefinition(pAdapter, efuseType, TYPE_AVAILABLE_EFUSE_BYTES_BANK, (void *)&efuse_max_available_len, bPseudoTest); |
| |
| while (efuse_addr < efuse_max_available_len) { |
| pg_header = ((pTargetPkt->offset & 0x07) << 5) | 0x0F; |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| |
| while (tmp_header == 0xFF) { |
| if (repeatcnt++ > EFUSE_REPEAT_THRESHOLD_) |
| return false; |
| |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| } |
| |
| /* to write ext_header */ |
| if (tmp_header == pg_header) { |
| efuse_addr++; |
| pg_header_temp = pg_header; |
| pg_header = ((pTargetPkt->offset & 0x78) << 1) | pTargetPkt->word_en; |
| |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| |
| while (tmp_header == 0xFF) { |
| if (repeatcnt++ > EFUSE_REPEAT_THRESHOLD_) |
| return false; |
| |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| } |
| |
| if ((tmp_header & 0x0F) == 0x0F) { /* word_en PG fail */ |
| if (repeatcnt++ > EFUSE_REPEAT_THRESHOLD_) { |
| return false; |
| } else { |
| efuse_addr++; |
| continue; |
| } |
| } else if (pg_header != tmp_header) { /* offset PG fail */ |
| struct pgpkt fixPkt; |
| fixPkt.offset = ((pg_header_temp & 0xE0) >> 5) | ((tmp_header & 0xF0) >> 1); |
| fixPkt.word_en = tmp_header & 0x0F; |
| fixPkt.word_cnts = Efuse_CalculateWordCnts(fixPkt.word_en); |
| if (!hal_EfuseFixHeaderProcess(pAdapter, efuseType, &fixPkt, &efuse_addr, bPseudoTest)) |
| return false; |
| } else { |
| bRet = true; |
| break; |
| } |
| } else if ((tmp_header & 0x1F) == 0x0F) { /* wrong extended header */ |
| efuse_addr += 2; |
| continue; |
| } |
| } |
| |
| *pAddr = efuse_addr; |
| return bRet; |
| } |
| |
| static bool hal_EfusePgPacketWrite1ByteHeader(struct adapter *pAdapter, u8 efuseType, u16 *pAddr, struct pgpkt *pTargetPkt, bool bPseudoTest) |
| { |
| bool bRet = false; |
| u8 pg_header = 0, tmp_header = 0; |
| u16 efuse_addr = *pAddr; |
| u8 repeatcnt = 0; |
| |
| pg_header = ((pTargetPkt->offset << 4) & 0xf0) | pTargetPkt->word_en; |
| |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| |
| while (tmp_header == 0xFF) { |
| if (repeatcnt++ > EFUSE_REPEAT_THRESHOLD_) |
| return false; |
| efuse_OneByteWrite(pAdapter, efuse_addr, pg_header, bPseudoTest); |
| efuse_OneByteRead(pAdapter, efuse_addr, &tmp_header, bPseudoTest); |
| } |
| |
| if (pg_header == tmp_header) { |
| bRet = true; |
| } else { |
| struct pgpkt fixPkt; |
| fixPkt.offset = (tmp_header >> 4) & 0x0F; |
| fixPkt.word_en = tmp_header & 0x0F; |
| fixPkt.word_cnts = Efuse_CalculateWordCnts(fixPkt.word_en); |
| if (!hal_EfuseFixHeaderProcess(pAdapter, efuseType, &fixPkt, &efuse_addr, bPseudoTest)) |
| return false; |
| } |
| |
| *pAddr = efuse_addr; |
| return bRet; |
| } |
| |
| static bool hal_EfusePgPacketWriteData(struct adapter *pAdapter, u8 efuseType, u16 *pAddr, struct pgpkt *pTargetPkt, bool bPseudoTest) |
| { |
| u16 efuse_addr = *pAddr; |
| u8 badworden; |
| u32 PgWriteSuccess = 0; |
| |
| badworden = rtl8188e_Efuse_WordEnableDataWrite(pAdapter, efuse_addr + 1, pTargetPkt->word_en, pTargetPkt->data, bPseudoTest); |
| if (badworden == 0x0F) { |
| /* write ok */ |
| return true; |
| } else { |
| /* reorganize other pg packet */ |
| PgWriteSuccess = rtl8188e_Efuse_PgPacketWrite(pAdapter, pTargetPkt->offset, badworden, pTargetPkt->data, bPseudoTest); |
| if (!PgWriteSuccess) |
| return false; |
| else |
| return true; |
| } |
| } |
| |
| static bool |
| hal_EfusePgPacketWriteHeader( |
| struct adapter *pAdapter, |
| u8 efuseType, |
| u16 *pAddr, |
| struct pgpkt *pTargetPkt, |
| bool bPseudoTest) |
| { |
| bool bRet = false; |
| |
| if (pTargetPkt->offset >= EFUSE_MAX_SECTION_BASE) |
| bRet = hal_EfusePgPacketWrite2ByteHeader(pAdapter, efuseType, pAddr, pTargetPkt, bPseudoTest); |
| else |
| bRet = hal_EfusePgPacketWrite1ByteHeader(pAdapter, efuseType, pAddr, pTargetPkt, bPseudoTest); |
| |
| return bRet; |
| } |
| |
| static bool wordEnMatched(struct pgpkt *pTargetPkt, struct pgpkt *pCurPkt, |
| u8 *pWden) |
| { |
| u8 match_word_en = 0x0F; /* default all words are disabled */ |
| |
| /* check if the same words are enabled both target and current PG packet */ |
| if (((pTargetPkt->word_en & BIT(0)) == 0) && |
| ((pCurPkt->word_en & BIT(0)) == 0)) |
| match_word_en &= ~BIT(0); /* enable word 0 */ |
| if (((pTargetPkt->word_en & BIT(1)) == 0) && |
| ((pCurPkt->word_en & BIT(1)) == 0)) |
| match_word_en &= ~BIT(1); /* enable word 1 */ |
| if (((pTargetPkt->word_en & BIT(2)) == 0) && |
| ((pCurPkt->word_en & BIT(2)) == 0)) |
| match_word_en &= ~BIT(2); /* enable word 2 */ |
| if (((pTargetPkt->word_en & BIT(3)) == 0) && |
| ((pCurPkt->word_en & BIT(3)) == 0)) |
| match_word_en &= ~BIT(3); /* enable word 3 */ |
| |
| *pWden = match_word_en; |
| |
| if (match_word_en != 0xf) |
| return true; |
| else |
| return false; |
| } |
| |
| static bool hal_EfuseCheckIfDatafollowed(struct adapter *pAdapter, u8 word_cnts, u16 startAddr, bool bPseudoTest) |
| { |
| bool bRet = false; |
| u8 i, efuse_data; |
| |
| for (i = 0; i < (word_cnts * 2); i++) { |
| if (efuse_OneByteRead(pAdapter, (startAddr + i), &efuse_data, bPseudoTest) && (efuse_data != 0xFF)) |
| bRet = true; |
| } |
| return bRet; |
| } |
| |
| static bool hal_EfusePartialWriteCheck(struct adapter *pAdapter, u8 efuseType, u16 *pAddr, struct pgpkt *pTargetPkt, bool bPseudoTest) |
| { |
| bool bRet = false; |
| u8 i, efuse_data = 0, cur_header = 0; |
| u8 matched_wden = 0, badworden = 0; |
| u16 startAddr = 0, efuse_max_available_len = 0, efuse_max = 0; |
| struct pgpkt curPkt; |
| |
| rtl8188e_EFUSE_GetEfuseDefinition(pAdapter, efuseType, TYPE_AVAILABLE_EFUSE_BYTES_BANK, (void *)&efuse_max_available_len, bPseudoTest); |
| rtl8188e_EFUSE_GetEfuseDefinition(pAdapter, efuseType, TYPE_EFUSE_REAL_CONTENT_LEN, (void *)&efuse_max, bPseudoTest); |
| |
| if (efuseType == EFUSE_WIFI) { |
| if (bPseudoTest) { |
| startAddr = (u16)(fakeEfuseUsedBytes % EFUSE_REAL_CONTENT_LEN); |
| } else { |
| GetHwReg8188EU(pAdapter, HW_VAR_EFUSE_BYTES, (u8 *)&startAddr); |
| startAddr %= EFUSE_REAL_CONTENT_LEN; |
| } |
| } else { |
| if (bPseudoTest) |
| startAddr = (u16)(fakeBTEfuseUsedBytes % EFUSE_REAL_CONTENT_LEN); |
| else |
| startAddr = (u16)(BTEfuseUsedBytes % EFUSE_REAL_CONTENT_LEN); |
| } |
| |
| while (1) { |
| if (startAddr >= efuse_max_available_len) { |
| bRet = false; |
| break; |
| } |
| |
| if (efuse_OneByteRead(pAdapter, startAddr, &efuse_data, bPseudoTest) && (efuse_data != 0xFF)) { |
| if (EXT_HEADER(efuse_data)) { |
| cur_header = efuse_data; |
| startAddr++; |
| efuse_OneByteRead(pAdapter, startAddr, &efuse_data, bPseudoTest); |
| if (ALL_WORDS_DISABLED(efuse_data)) { |
| bRet = false; |
| break; |
| } else { |
| curPkt.offset = ((cur_header & 0xE0) >> 5) | ((efuse_data & 0xF0) >> 1); |
| curPkt.word_en = efuse_data & 0x0F; |
| } |
| } else { |
| cur_header = efuse_data; |
| curPkt.offset = (cur_header >> 4) & 0x0F; |
| curPkt.word_en = cur_header & 0x0F; |
| } |
| |
| curPkt.word_cnts = Efuse_CalculateWordCnts(curPkt.word_en); |
| /* if same header is found but no data followed */ |
| /* write some part of data followed by the header. */ |
| if ((curPkt.offset == pTargetPkt->offset) && |
| (!hal_EfuseCheckIfDatafollowed(pAdapter, curPkt.word_cnts, startAddr + 1, bPseudoTest)) && |
| wordEnMatched(pTargetPkt, &curPkt, &matched_wden)) { |
| /* Here to write partial data */ |
| badworden = rtl8188e_Efuse_WordEnableDataWrite(pAdapter, startAddr + 1, matched_wden, pTargetPkt->data, bPseudoTest); |
| if (badworden != 0x0F) { |
| u32 PgWriteSuccess = 0; |
| /* if write fail on some words, write these bad words again */ |
| |
| PgWriteSuccess = rtl8188e_Efuse_PgPacketWrite(pAdapter, pTargetPkt->offset, badworden, pTargetPkt->data, bPseudoTest); |
| |
| if (!PgWriteSuccess) { |
| bRet = false; /* write fail, return */ |
| break; |
| } |
| } |
| /* partial write ok, update the target packet for later use */ |
| for (i = 0; i < 4; i++) { |
| if ((matched_wden & (0x1 << i)) == 0) /* this word has been written */ |
| pTargetPkt->word_en |= (0x1 << i); /* disable the word */ |
| } |
| pTargetPkt->word_cnts = Efuse_CalculateWordCnts(pTargetPkt->word_en); |
| } |
| /* read from next header */ |
| startAddr = startAddr + (curPkt.word_cnts * 2) + 1; |
| } else { |
| /* not used header, 0xff */ |
| *pAddr = startAddr; |
| bRet = true; |
| break; |
| } |
| } |
| return bRet; |
| } |
| |
| static bool |
| hal_EfusePgCheckAvailableAddr( |
| struct adapter *pAdapter, |
| u8 efuseType, |
| bool bPseudoTest |
| ) |
| { |
| u16 efuse_max_available_len = 0; |
| |
| /* Change to check TYPE_EFUSE_MAP_LEN , because 8188E raw 256, logic map over 256. */ |
| rtl8188e_EFUSE_GetEfuseDefinition(pAdapter, EFUSE_WIFI, TYPE_EFUSE_MAP_LEN, (void *)&efuse_max_available_len, false); |
| |
| if (rtl8188e_EfuseGetCurrentSize(pAdapter, efuseType, bPseudoTest) >= efuse_max_available_len) |
| return false; |
| return true; |
| } |
| |
| static void hal_EfuseConstructPGPkt(u8 offset, u8 word_en, u8 *pData, struct pgpkt *pTargetPkt) |
| { |
| memset((void *)pTargetPkt->data, 0xFF, sizeof(u8) * 8); |
| pTargetPkt->offset = offset; |
| pTargetPkt->word_en = word_en; |
| efuse_WordEnableDataRead(word_en, pData, pTargetPkt->data); |
| pTargetPkt->word_cnts = Efuse_CalculateWordCnts(pTargetPkt->word_en); |
| } |
| |
| static bool hal_EfusePgPacketWrite_8188e(struct adapter *pAdapter, u8 offset, u8 word_en, u8 *pData, bool bPseudoTest) |
| { |
| struct pgpkt targetPkt; |
| u16 startAddr = 0; |
| u8 efuseType = EFUSE_WIFI; |
| |
| if (!hal_EfusePgCheckAvailableAddr(pAdapter, efuseType, bPseudoTest)) |
| return false; |
| |
| hal_EfuseConstructPGPkt(offset, word_en, pData, &targetPkt); |
| |
| if (!hal_EfusePartialWriteCheck(pAdapter, efuseType, &startAddr, &targetPkt, bPseudoTest)) |
| return false; |
| |
| if (!hal_EfusePgPacketWriteHeader(pAdapter, efuseType, &startAddr, &targetPkt, bPseudoTest)) |
| return false; |
| |
| if (!hal_EfusePgPacketWriteData(pAdapter, efuseType, &startAddr, &targetPkt, bPseudoTest)) |
| return false; |
| |
| return true; |
| } |
| |
| static int Hal_EfusePgPacketWrite_Pseudo(struct adapter *pAdapter, u8 offset, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| int ret; |
| |
| ret = hal_EfusePgPacketWrite_8188e(pAdapter, offset, word_en, data, bPseudoTest); |
| return ret; |
| } |
| |
| static int Hal_EfusePgPacketWrite(struct adapter *pAdapter, u8 offset, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| int ret = 0; |
| ret = hal_EfusePgPacketWrite_8188e(pAdapter, offset, word_en, data, bPseudoTest); |
| |
| return ret; |
| } |
| |
| int rtl8188e_Efuse_PgPacketWrite(struct adapter *pAdapter, u8 offset, u8 word_en, u8 *data, bool bPseudoTest) |
| { |
| int ret; |
| |
| if (bPseudoTest) |
| ret = Hal_EfusePgPacketWrite_Pseudo(pAdapter, offset, word_en, data, bPseudoTest); |
| else |
| ret = Hal_EfusePgPacketWrite(pAdapter, offset, word_en, data, bPseudoTest); |
| return ret; |
| } |
| |
| void rtl8188e_read_chip_version(struct adapter *padapter) |
| { |
| u32 value32; |
| struct HAL_VERSION ChipVersion; |
| struct hal_data_8188e *pHalData; |
| |
| pHalData = GET_HAL_DATA(padapter); |
| |
| value32 = rtw_read32(padapter, REG_SYS_CFG); |
| ChipVersion.ChipType = ((value32 & RTL_ID) ? TEST_CHIP : NORMAL_CHIP); |
| |
| ChipVersion.RFType = RF_TYPE_1T1R; |
| ChipVersion.VendorType = ((value32 & VENDOR_ID) ? CHIP_VENDOR_UMC : CHIP_VENDOR_TSMC); |
| ChipVersion.CUTVersion = (value32 & CHIP_VER_RTL_MASK) >> CHIP_VER_RTL_SHIFT; /* IC version (CUT) */ |
| ChipVersion.ROMVer = 0; /* ROM code version. */ |
| |
| dump_chip_info(ChipVersion); |
| |
| pHalData->VersionID = ChipVersion; |
| |
| pHalData->rf_type = RF_1T1R; |
| |
| MSG_88E("RF_Type is %x!!\n", pHalData->rf_type); |
| } |
| |
| void rtl8188e_SetHalODMVar(struct adapter *Adapter, enum hal_odm_variable eVariable, void *pValue1, bool bSet) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(Adapter); |
| struct odm_dm_struct *podmpriv = &pHalData->odmpriv; |
| switch (eVariable) { |
| case HAL_ODM_STA_INFO: |
| { |
| struct sta_info *psta = (struct sta_info *)pValue1; |
| |
| if (bSet) { |
| DBG_88E("### Set STA_(%d) info\n", psta->mac_id); |
| podmpriv->pODM_StaInfo[psta->mac_id] = psta; |
| ODM_RAInfo_Init(podmpriv, psta->mac_id); |
| } else { |
| DBG_88E("### Clean STA_(%d) info\n", psta->mac_id); |
| podmpriv->pODM_StaInfo[psta->mac_id] = NULL; |
| } |
| } |
| break; |
| case HAL_ODM_P2P_STATE: |
| ODM_CmnInfoUpdate(podmpriv, ODM_CMNINFO_WIFI_DIRECT, bSet); |
| break; |
| case HAL_ODM_WIFI_DISPLAY_STATE: |
| ODM_CmnInfoUpdate(podmpriv, ODM_CMNINFO_WIFI_DISPLAY, bSet); |
| break; |
| default: |
| break; |
| } |
| } |
| |
| void hal_notch_filter_8188e(struct adapter *adapter, bool enable) |
| { |
| if (enable) { |
| DBG_88E("Enable notch filter\n"); |
| rtw_write8(adapter, rOFDM0_RxDSP + 1, rtw_read8(adapter, rOFDM0_RxDSP + 1) | BIT(1)); |
| } else { |
| DBG_88E("Disable notch filter\n"); |
| rtw_write8(adapter, rOFDM0_RxDSP + 1, rtw_read8(adapter, rOFDM0_RxDSP + 1) & ~BIT(1)); |
| } |
| } |
| |
| u8 GetEEPROMSize8188E(struct adapter *padapter) |
| { |
| u8 size = 0; |
| u32 cr; |
| |
| cr = rtw_read16(padapter, REG_9346CR); |
| /* 6: EEPROM used is 93C46, 4: boot from E-Fuse. */ |
| size = (cr & BOOT_FROM_EEPROM) ? 6 : 4; |
| |
| MSG_88E("EEPROM type is %s\n", size == 4 ? "E-FUSE" : "93C46"); |
| |
| return size; |
| } |
| |
| /* */ |
| /* */ |
| /* LLT R/W/Init function */ |
| /* */ |
| /* */ |
| static s32 _LLTWrite(struct adapter *padapter, u32 address, u32 data) |
| { |
| s32 status = _SUCCESS; |
| s32 count = 0; |
| u32 value = _LLT_INIT_ADDR(address) | _LLT_INIT_DATA(data) | _LLT_OP(_LLT_WRITE_ACCESS); |
| u16 LLTReg = REG_LLT_INIT; |
| |
| rtw_write32(padapter, LLTReg, value); |
| |
| /* polling */ |
| do { |
| value = rtw_read32(padapter, LLTReg); |
| if (_LLT_NO_ACTIVE == _LLT_OP_VALUE(value)) |
| break; |
| |
| if (count > POLLING_LLT_THRESHOLD) { |
| status = _FAIL; |
| break; |
| } |
| } while (count++); |
| |
| return status; |
| } |
| |
| s32 InitLLTTable(struct adapter *padapter, u8 txpktbuf_bndy) |
| { |
| s32 status = _FAIL; |
| u32 i; |
| u32 Last_Entry_Of_TxPktBuf = LAST_ENTRY_OF_TX_PKT_BUFFER;/* 176, 22k */ |
| |
| if (rtw_IOL_applied(padapter)) { |
| status = iol_InitLLTTable(padapter, txpktbuf_bndy); |
| } else { |
| for (i = 0; i < (txpktbuf_bndy - 1); i++) { |
| status = _LLTWrite(padapter, i, i + 1); |
| if (_SUCCESS != status) |
| return status; |
| } |
| |
| /* end of list */ |
| status = _LLTWrite(padapter, (txpktbuf_bndy - 1), 0xFF); |
| if (_SUCCESS != status) |
| return status; |
| |
| /* Make the other pages as ring buffer */ |
| /* This ring buffer is used as beacon buffer if we config this MAC as two MAC transfer. */ |
| /* Otherwise used as local loopback buffer. */ |
| for (i = txpktbuf_bndy; i < Last_Entry_Of_TxPktBuf; i++) { |
| status = _LLTWrite(padapter, i, (i + 1)); |
| if (_SUCCESS != status) |
| return status; |
| } |
| |
| /* Let last entry point to the start entry of ring buffer */ |
| status = _LLTWrite(padapter, Last_Entry_Of_TxPktBuf, txpktbuf_bndy); |
| if (_SUCCESS != status) { |
| return status; |
| } |
| } |
| |
| return status; |
| } |
| |
| void |
| Hal_InitPGData88E(struct adapter *padapter) |
| { |
| struct eeprom_priv *pEEPROM = &padapter->eeprompriv; |
| |
| if (!pEEPROM->bautoload_fail_flag) { /* autoload OK. */ |
| if (!is_boot_from_eeprom(padapter)) { |
| /* Read EFUSE real map to shadow. */ |
| EFUSE_ShadowMapUpdate(padapter, EFUSE_WIFI, false); |
| } |
| } else {/* autoload fail */ |
| /* update to default value 0xFF */ |
| if (!is_boot_from_eeprom(padapter)) |
| EFUSE_ShadowMapUpdate(padapter, EFUSE_WIFI, false); |
| } |
| } |
| |
| void |
| Hal_EfuseParseIDCode88E( |
| struct adapter *padapter, |
| u8 *hwinfo |
| ) |
| { |
| struct eeprom_priv *pEEPROM = &padapter->eeprompriv; |
| u16 EEPROMId; |
| |
| /* Check 0x8129 again for making sure autoload status!! */ |
| EEPROMId = le16_to_cpu(*((__le16 *)hwinfo)); |
| if (EEPROMId != RTL_EEPROM_ID) { |
| pr_err("EEPROM ID(%#x) is invalid!!\n", EEPROMId); |
| pEEPROM->bautoload_fail_flag = true; |
| } else { |
| pEEPROM->bautoload_fail_flag = false; |
| } |
| |
| pr_info("EEPROM ID = 0x%04x\n", EEPROMId); |
| } |
| |
| static void Hal_ReadPowerValueFromPROM_8188E(struct txpowerinfo24g *pwrInfo24G, u8 *PROMContent, bool AutoLoadFail) |
| { |
| u32 rfPath, eeAddr = EEPROM_TX_PWR_INX_88E, group, TxCount = 0; |
| |
| memset(pwrInfo24G, 0, sizeof(struct txpowerinfo24g)); |
| |
| if (AutoLoadFail) { |
| for (rfPath = 0; rfPath < RF_PATH_MAX; rfPath++) { |
| /* 2.4G default value */ |
| for (group = 0; group < MAX_CHNL_GROUP_24G; group++) { |
| pwrInfo24G->IndexCCK_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX; |
| pwrInfo24G->IndexBW40_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX; |
| } |
| for (TxCount = 0; TxCount < MAX_TX_COUNT; TxCount++) { |
| if (TxCount == 0) { |
| pwrInfo24G->BW20_Diff[rfPath][0] = EEPROM_DEFAULT_24G_HT20_DIFF; |
| pwrInfo24G->OFDM_Diff[rfPath][0] = EEPROM_DEFAULT_24G_OFDM_DIFF; |
| } else { |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| pwrInfo24G->BW40_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| pwrInfo24G->CCK_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| } |
| } |
| } |
| return; |
| } |
| |
| for (rfPath = 0; rfPath < RF_PATH_MAX; rfPath++) { |
| /* 2.4G default value */ |
| for (group = 0; group < MAX_CHNL_GROUP_24G; group++) { |
| pwrInfo24G->IndexCCK_Base[rfPath][group] = PROMContent[eeAddr++]; |
| if (pwrInfo24G->IndexCCK_Base[rfPath][group] == 0xFF) |
| pwrInfo24G->IndexCCK_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX; |
| } |
| for (group = 0; group < MAX_CHNL_GROUP_24G - 1; group++) { |
| pwrInfo24G->IndexBW40_Base[rfPath][group] = PROMContent[eeAddr++]; |
| if (pwrInfo24G->IndexBW40_Base[rfPath][group] == 0xFF) |
| pwrInfo24G->IndexBW40_Base[rfPath][group] = EEPROM_DEFAULT_24G_INDEX; |
| } |
| for (TxCount = 0; TxCount < MAX_TX_COUNT; TxCount++) { |
| if (TxCount == 0) { |
| pwrInfo24G->BW40_Diff[rfPath][TxCount] = 0; |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] = EEPROM_DEFAULT_24G_HT20_DIFF; |
| } else { |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0xf0) >> 4; |
| if (pwrInfo24G->BW20_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] = EEPROM_DEFAULT_24G_OFDM_DIFF; |
| } else { |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0x0f); |
| if (pwrInfo24G->OFDM_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| pwrInfo24G->CCK_Diff[rfPath][TxCount] = 0; |
| eeAddr++; |
| } else { |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->BW40_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| } else { |
| pwrInfo24G->BW40_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0xf0) >> 4; |
| if (pwrInfo24G->BW40_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->BW40_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| } else { |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0x0f); |
| if (pwrInfo24G->BW20_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->BW20_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| eeAddr++; |
| |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| } else { |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0xf0) >> 4; |
| if (pwrInfo24G->OFDM_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->OFDM_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| |
| if (PROMContent[eeAddr] == 0xFF) { |
| pwrInfo24G->CCK_Diff[rfPath][TxCount] = EEPROM_DEFAULT_DIFF; |
| } else { |
| pwrInfo24G->CCK_Diff[rfPath][TxCount] = (PROMContent[eeAddr] & 0x0f); |
| if (pwrInfo24G->CCK_Diff[rfPath][TxCount] & BIT(3)) /* 4bit sign number to 8 bit sign number */ |
| pwrInfo24G->CCK_Diff[rfPath][TxCount] |= 0xF0; |
| } |
| eeAddr++; |
| } |
| } |
| } |
| } |
| |
| static void hal_get_chnl_group_88e(u8 chnl, u8 *group) |
| { |
| if (chnl < 3) /* Channel 1-2 */ |
| *group = 0; |
| else if (chnl < 6) /* Channel 3-5 */ |
| *group = 1; |
| else if (chnl < 9) /* Channel 6-8 */ |
| *group = 2; |
| else if (chnl < 12) /* Channel 9-11 */ |
| *group = 3; |
| else if (chnl < 14) /* Channel 12-13 */ |
| *group = 4; |
| else if (chnl == 14) /* Channel 14 */ |
| *group = 5; |
| } |
| |
| void Hal_ReadPowerSavingMode88E(struct adapter *padapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| if (AutoLoadFail) { |
| padapter->pwrctrlpriv.bHWPowerdown = false; |
| padapter->pwrctrlpriv.bSupportRemoteWakeup = false; |
| } else { |
| /* hw power down mode selection , 0:rf-off / 1:power down */ |
| |
| if (padapter->registrypriv.hwpdn_mode == 2) |
| padapter->pwrctrlpriv.bHWPowerdown = (hwinfo[EEPROM_RF_FEATURE_OPTION_88E] & BIT(4)); |
| else |
| padapter->pwrctrlpriv.bHWPowerdown = padapter->registrypriv.hwpdn_mode; |
| |
| /* decide hw if support remote wakeup function */ |
| /* if hw supported, 8051 (SIE) will generate WeakUP signal(D+/D- toggle) when autoresume */ |
| padapter->pwrctrlpriv.bSupportRemoteWakeup = (hwinfo[EEPROM_USB_OPTIONAL_FUNCTION0] & BIT(1)) ? true : false; |
| |
| DBG_88E("%s...bHWPowerdown(%x) , bSupportRemoteWakeup(%x)\n", __func__, |
| padapter->pwrctrlpriv.bHWPowerdown, padapter->pwrctrlpriv.bSupportRemoteWakeup); |
| |
| DBG_88E("### PS params => power_mgnt(%x), usbss_enable(%x) ###\n", padapter->registrypriv.power_mgnt, padapter->registrypriv.usbss_enable); |
| } |
| } |
| |
| void Hal_ReadTxPowerInfo88E(struct adapter *padapter, u8 *PROMContent, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(padapter); |
| struct txpowerinfo24g pwrInfo24G; |
| u8 rfPath = 0; |
| u8 ch, group; |
| u8 TxCount; |
| |
| Hal_ReadPowerValueFromPROM_8188E(&pwrInfo24G, PROMContent, AutoLoadFail); |
| |
| if (!AutoLoadFail) |
| pHalData->bTXPowerDataReadFromEEPORM = true; |
| |
| for (ch = 0; ch < CHANNEL_MAX_NUMBER; ch++) { |
| hal_get_chnl_group_88e(ch, &group); |
| |
| pHalData->Index24G_CCK_Base[rfPath][ch] = pwrInfo24G.IndexCCK_Base[rfPath][group]; |
| if (ch == 14) |
| pHalData->Index24G_BW40_Base[rfPath][ch] = pwrInfo24G.IndexBW40_Base[rfPath][4]; |
| else |
| pHalData->Index24G_BW40_Base[rfPath][ch] = pwrInfo24G.IndexBW40_Base[rfPath][group]; |
| |
| DBG_88E("======= Path %d, Channel %d =======\n", rfPath, ch); |
| DBG_88E("Index24G_CCK_Base[%d][%d] = 0x%x\n", rfPath, ch, pHalData->Index24G_CCK_Base[rfPath][ch]); |
| DBG_88E("Index24G_BW40_Base[%d][%d] = 0x%x\n", rfPath, ch, pHalData->Index24G_BW40_Base[rfPath][ch]); |
| } |
| for (TxCount = 0; TxCount < MAX_TX_COUNT; TxCount++) { |
| pHalData->CCK_24G_Diff[rfPath][TxCount] = pwrInfo24G.CCK_Diff[rfPath][TxCount]; |
| pHalData->OFDM_24G_Diff[rfPath][TxCount] = pwrInfo24G.OFDM_Diff[rfPath][TxCount]; |
| pHalData->BW20_24G_Diff[rfPath][TxCount] = pwrInfo24G.BW20_Diff[rfPath][TxCount]; |
| pHalData->BW40_24G_Diff[rfPath][TxCount] = pwrInfo24G.BW40_Diff[rfPath][TxCount]; |
| DBG_88E("======= TxCount %d =======\n", TxCount); |
| DBG_88E("CCK_24G_Diff[%d][%d] = %d\n", rfPath, TxCount, pHalData->CCK_24G_Diff[rfPath][TxCount]); |
| DBG_88E("OFDM_24G_Diff[%d][%d] = %d\n", rfPath, TxCount, pHalData->OFDM_24G_Diff[rfPath][TxCount]); |
| DBG_88E("BW20_24G_Diff[%d][%d] = %d\n", rfPath, TxCount, pHalData->BW20_24G_Diff[rfPath][TxCount]); |
| DBG_88E("BW40_24G_Diff[%d][%d] = %d\n", rfPath, TxCount, pHalData->BW40_24G_Diff[rfPath][TxCount]); |
| } |
| |
| /* 2010/10/19 MH Add Regulator recognize for CU. */ |
| if (!AutoLoadFail) { |
| pHalData->EEPROMRegulatory = (PROMContent[EEPROM_RF_BOARD_OPTION_88E] & 0x7); /* bit0~2 */ |
| if (PROMContent[EEPROM_RF_BOARD_OPTION_88E] == 0xFF) |
| pHalData->EEPROMRegulatory = (EEPROM_DEFAULT_BOARD_OPTION & 0x7); /* bit0~2 */ |
| } else { |
| pHalData->EEPROMRegulatory = 0; |
| } |
| DBG_88E("EEPROMRegulatory = 0x%x\n", pHalData->EEPROMRegulatory); |
| } |
| |
| void Hal_EfuseParseXtal_8188E(struct adapter *pAdapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(pAdapter); |
| |
| if (!AutoLoadFail) { |
| pHalData->CrystalCap = hwinfo[EEPROM_XTAL_88E]; |
| if (pHalData->CrystalCap == 0xFF) |
| pHalData->CrystalCap = EEPROM_Default_CrystalCap_88E; |
| } else { |
| pHalData->CrystalCap = EEPROM_Default_CrystalCap_88E; |
| } |
| DBG_88E("CrystalCap: 0x%2x\n", pHalData->CrystalCap); |
| } |
| |
| void Hal_EfuseParseBoardType88E(struct adapter *pAdapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(pAdapter); |
| |
| if (!AutoLoadFail) |
| pHalData->BoardType = ((hwinfo[EEPROM_RF_BOARD_OPTION_88E] & 0xE0) >> 5); |
| else |
| pHalData->BoardType = 0; |
| DBG_88E("Board Type: 0x%2x\n", pHalData->BoardType); |
| } |
| |
| void Hal_EfuseParseEEPROMVer88E(struct adapter *padapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(padapter); |
| |
| if (!AutoLoadFail) { |
| pHalData->EEPROMVersion = hwinfo[EEPROM_VERSION_88E]; |
| if (pHalData->EEPROMVersion == 0xFF) |
| pHalData->EEPROMVersion = EEPROM_Default_Version; |
| } else { |
| pHalData->EEPROMVersion = 1; |
| } |
| } |
| |
| void rtl8188e_EfuseParseChnlPlan(struct adapter *padapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| padapter->mlmepriv.ChannelPlan = |
| hal_com_get_channel_plan(padapter, |
| hwinfo ? hwinfo[EEPROM_ChannelPlan_88E] : 0xFF, |
| padapter->registrypriv.channel_plan, |
| RT_CHANNEL_DOMAIN_WORLD_WIDE_13, AutoLoadFail); |
| |
| DBG_88E("mlmepriv.ChannelPlan = 0x%02x\n", padapter->mlmepriv.ChannelPlan); |
| } |
| |
| void Hal_EfuseParseCustomerID88E(struct adapter *padapter, u8 *hwinfo, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(padapter); |
| |
| if (!AutoLoadFail) { |
| pHalData->EEPROMCustomerID = hwinfo[EEPROM_CUSTOMERID_88E]; |
| } else { |
| pHalData->EEPROMCustomerID = 0; |
| pHalData->EEPROMSubCustomerID = 0; |
| } |
| DBG_88E("EEPROM Customer ID: 0x%2x\n", pHalData->EEPROMCustomerID); |
| } |
| |
| void Hal_ReadAntennaDiversity88E(struct adapter *pAdapter, u8 *PROMContent, bool AutoLoadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(pAdapter); |
| struct registry_priv *registry_par = &pAdapter->registrypriv; |
| |
| if (!AutoLoadFail) { |
| /* Antenna Diversity setting. */ |
| if (registry_par->antdiv_cfg == 2) { /* 2:By EFUSE */ |
| pHalData->AntDivCfg = (PROMContent[EEPROM_RF_BOARD_OPTION_88E] & 0x18) >> 3; |
| if (PROMContent[EEPROM_RF_BOARD_OPTION_88E] == 0xFF) |
| pHalData->AntDivCfg = (EEPROM_DEFAULT_BOARD_OPTION & 0x18) >> 3; |
| } else { |
| pHalData->AntDivCfg = registry_par->antdiv_cfg; /* 0:OFF , 1:ON, 2:By EFUSE */ |
| } |
| |
| if (registry_par->antdiv_type == 0) { |
| /* If TRxAntDivType is AUTO in advanced setting, use EFUSE value instead. */ |
| pHalData->TRxAntDivType = PROMContent[EEPROM_RF_ANTENNA_OPT_88E]; |
| if (pHalData->TRxAntDivType == 0xFF) |
| pHalData->TRxAntDivType = CG_TRX_HW_ANTDIV; /* For 88EE, 1Tx and 1RxCG are fixed.(1Ant, Tx and RxCG are both on aux port) */ |
| } else { |
| pHalData->TRxAntDivType = registry_par->antdiv_type; |
| } |
| |
| if (pHalData->TRxAntDivType == CG_TRX_HW_ANTDIV || pHalData->TRxAntDivType == CGCS_RX_HW_ANTDIV) |
| pHalData->AntDivCfg = 1; /* 0xC1[3] is ignored. */ |
| } else { |
| pHalData->AntDivCfg = 0; |
| } |
| DBG_88E("EEPROM : AntDivCfg = %x, TRxAntDivType = %x\n", pHalData->AntDivCfg, pHalData->TRxAntDivType); |
| } |
| |
| void Hal_ReadThermalMeter_88E(struct adapter *Adapter, u8 *PROMContent, bool AutoloadFail) |
| { |
| struct hal_data_8188e *pHalData = GET_HAL_DATA(Adapter); |
| |
| /* ThermalMeter from EEPROM */ |
| if (!AutoloadFail) |
| pHalData->EEPROMThermalMeter = PROMContent[EEPROM_THERMAL_METER_88E]; |
| else |
| pHalData->EEPROMThermalMeter = EEPROM_Default_ThermalMeter_88E; |
| |
| if (pHalData->EEPROMThermalMeter == 0xff || AutoloadFail) { |
| pHalData->bAPKThermalMeterIgnore = true; |
| pHalData->EEPROMThermalMeter = EEPROM_Default_ThermalMeter_88E; |
| } |
| DBG_88E("ThermalMeter = 0x%x\n", pHalData->EEPROMThermalMeter); |
| } |