| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * Meson8, Meson8b and GXBB USB2 PHY driver |
| * |
| * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com> |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/delay.h> |
| #include <linux/io.h> |
| #include <linux/module.h> |
| #include <linux/of_device.h> |
| #include <linux/reset.h> |
| #include <linux/phy/phy.h> |
| #include <linux/platform_device.h> |
| #include <linux/usb/of.h> |
| |
| #define REG_CONFIG 0x00 |
| #define REG_CONFIG_CLK_EN BIT(0) |
| #define REG_CONFIG_CLK_SEL_MASK GENMASK(3, 1) |
| #define REG_CONFIG_CLK_DIV_MASK GENMASK(10, 4) |
| #define REG_CONFIG_CLK_32k_ALTSEL BIT(15) |
| #define REG_CONFIG_TEST_TRIG BIT(31) |
| |
| #define REG_CTRL 0x04 |
| #define REG_CTRL_SOFT_PRST BIT(0) |
| #define REG_CTRL_SOFT_HRESET BIT(1) |
| #define REG_CTRL_SS_SCALEDOWN_MODE_MASK GENMASK(3, 2) |
| #define REG_CTRL_CLK_DET_RST BIT(4) |
| #define REG_CTRL_INTR_SEL BIT(5) |
| #define REG_CTRL_CLK_DETECTED BIT(8) |
| #define REG_CTRL_SOF_SENT_RCVD_TGL BIT(9) |
| #define REG_CTRL_SOF_TOGGLE_OUT BIT(10) |
| #define REG_CTRL_POWER_ON_RESET BIT(15) |
| #define REG_CTRL_SLEEPM BIT(16) |
| #define REG_CTRL_TX_BITSTUFF_ENN_H BIT(17) |
| #define REG_CTRL_TX_BITSTUFF_ENN BIT(18) |
| #define REG_CTRL_COMMON_ON BIT(19) |
| #define REG_CTRL_REF_CLK_SEL_MASK GENMASK(21, 20) |
| #define REG_CTRL_REF_CLK_SEL_SHIFT 20 |
| #define REG_CTRL_FSEL_MASK GENMASK(24, 22) |
| #define REG_CTRL_FSEL_SHIFT 22 |
| #define REG_CTRL_PORT_RESET BIT(25) |
| #define REG_CTRL_THREAD_ID_MASK GENMASK(31, 26) |
| |
| #define REG_ENDP_INTR 0x08 |
| |
| /* bits [31:26], [24:21] and [15:3] seem to be read-only */ |
| #define REG_ADP_BC 0x0c |
| #define REG_ADP_BC_VBUS_VLD_EXT_SEL BIT(0) |
| #define REG_ADP_BC_VBUS_VLD_EXT BIT(1) |
| #define REG_ADP_BC_OTG_DISABLE BIT(2) |
| #define REG_ADP_BC_ID_PULLUP BIT(3) |
| #define REG_ADP_BC_DRV_VBUS BIT(4) |
| #define REG_ADP_BC_ADP_PRB_EN BIT(5) |
| #define REG_ADP_BC_ADP_DISCHARGE BIT(6) |
| #define REG_ADP_BC_ADP_CHARGE BIT(7) |
| #define REG_ADP_BC_SESS_END BIT(8) |
| #define REG_ADP_BC_DEVICE_SESS_VLD BIT(9) |
| #define REG_ADP_BC_B_VALID BIT(10) |
| #define REG_ADP_BC_A_VALID BIT(11) |
| #define REG_ADP_BC_ID_DIG BIT(12) |
| #define REG_ADP_BC_VBUS_VALID BIT(13) |
| #define REG_ADP_BC_ADP_PROBE BIT(14) |
| #define REG_ADP_BC_ADP_SENSE BIT(15) |
| #define REG_ADP_BC_ACA_ENABLE BIT(16) |
| #define REG_ADP_BC_DCD_ENABLE BIT(17) |
| #define REG_ADP_BC_VDAT_DET_EN_B BIT(18) |
| #define REG_ADP_BC_VDAT_SRC_EN_B BIT(19) |
| #define REG_ADP_BC_CHARGE_SEL BIT(20) |
| #define REG_ADP_BC_CHARGE_DETECT BIT(21) |
| #define REG_ADP_BC_ACA_PIN_RANGE_C BIT(22) |
| #define REG_ADP_BC_ACA_PIN_RANGE_B BIT(23) |
| #define REG_ADP_BC_ACA_PIN_RANGE_A BIT(24) |
| #define REG_ADP_BC_ACA_PIN_GND BIT(25) |
| #define REG_ADP_BC_ACA_PIN_FLOAT BIT(26) |
| |
| #define REG_DBG_UART 0x10 |
| |
| #define REG_TEST 0x14 |
| #define REG_TEST_DATA_IN_MASK GENMASK(3, 0) |
| #define REG_TEST_EN_MASK GENMASK(7, 4) |
| #define REG_TEST_ADDR_MASK GENMASK(11, 8) |
| #define REG_TEST_DATA_OUT_SEL BIT(12) |
| #define REG_TEST_CLK BIT(13) |
| #define REG_TEST_VA_TEST_EN_B_MASK GENMASK(15, 14) |
| #define REG_TEST_DATA_OUT_MASK GENMASK(19, 16) |
| #define REG_TEST_DISABLE_ID_PULLUP BIT(20) |
| |
| #define REG_TUNE 0x18 |
| #define REG_TUNE_TX_RES_TUNE_MASK GENMASK(1, 0) |
| #define REG_TUNE_TX_HSXV_TUNE_MASK GENMASK(3, 2) |
| #define REG_TUNE_TX_VREF_TUNE_MASK GENMASK(7, 4) |
| #define REG_TUNE_TX_RISE_TUNE_MASK GENMASK(9, 8) |
| #define REG_TUNE_TX_PREEMP_PULSE_TUNE BIT(10) |
| #define REG_TUNE_TX_PREEMP_AMP_TUNE_MASK GENMASK(12, 11) |
| #define REG_TUNE_TX_FSLS_TUNE_MASK GENMASK(16, 13) |
| #define REG_TUNE_SQRX_TUNE_MASK GENMASK(19, 17) |
| #define REG_TUNE_OTG_TUNE GENMASK(22, 20) |
| #define REG_TUNE_COMP_DIS_TUNE GENMASK(25, 23) |
| #define REG_TUNE_HOST_DM_PULLDOWN BIT(26) |
| #define REG_TUNE_HOST_DP_PULLDOWN BIT(27) |
| |
| #define RESET_COMPLETE_TIME 500 |
| #define ACA_ENABLE_COMPLETE_TIME 50 |
| |
| struct phy_meson8b_usb2_priv { |
| void __iomem *regs; |
| enum usb_dr_mode dr_mode; |
| struct clk *clk_usb_general; |
| struct clk *clk_usb; |
| struct reset_control *reset; |
| }; |
| |
| static u32 phy_meson8b_usb2_read(struct phy_meson8b_usb2_priv *phy_priv, |
| u32 reg) |
| { |
| return readl(phy_priv->regs + reg); |
| } |
| |
| static void phy_meson8b_usb2_mask_bits(struct phy_meson8b_usb2_priv *phy_priv, |
| u32 reg, u32 mask, u32 value) |
| { |
| u32 data; |
| |
| data = phy_meson8b_usb2_read(phy_priv, reg); |
| data &= ~mask; |
| data |= (value & mask); |
| |
| writel(data, phy_priv->regs + reg); |
| } |
| |
| static int phy_meson8b_usb2_power_on(struct phy *phy) |
| { |
| struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy); |
| int ret; |
| |
| if (!IS_ERR_OR_NULL(priv->reset)) { |
| ret = reset_control_reset(priv->reset); |
| if (ret) { |
| dev_err(&phy->dev, "Failed to trigger USB reset\n"); |
| return ret; |
| } |
| } |
| |
| ret = clk_prepare_enable(priv->clk_usb_general); |
| if (ret) { |
| dev_err(&phy->dev, "Failed to enable USB general clock\n"); |
| return ret; |
| } |
| |
| ret = clk_prepare_enable(priv->clk_usb); |
| if (ret) { |
| dev_err(&phy->dev, "Failed to enable USB DDR clock\n"); |
| clk_disable_unprepare(priv->clk_usb_general); |
| return ret; |
| } |
| |
| phy_meson8b_usb2_mask_bits(priv, REG_CONFIG, REG_CONFIG_CLK_32k_ALTSEL, |
| REG_CONFIG_CLK_32k_ALTSEL); |
| |
| phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_REF_CLK_SEL_MASK, |
| 0x2 << REG_CTRL_REF_CLK_SEL_SHIFT); |
| |
| phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_FSEL_MASK, |
| 0x5 << REG_CTRL_FSEL_SHIFT); |
| |
| /* reset the PHY */ |
| phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, |
| REG_CTRL_POWER_ON_RESET); |
| udelay(RESET_COMPLETE_TIME); |
| phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_POWER_ON_RESET, 0); |
| udelay(RESET_COMPLETE_TIME); |
| |
| phy_meson8b_usb2_mask_bits(priv, REG_CTRL, REG_CTRL_SOF_TOGGLE_OUT, |
| REG_CTRL_SOF_TOGGLE_OUT); |
| |
| if (priv->dr_mode == USB_DR_MODE_HOST) { |
| phy_meson8b_usb2_mask_bits(priv, REG_ADP_BC, |
| REG_ADP_BC_ACA_ENABLE, |
| REG_ADP_BC_ACA_ENABLE); |
| |
| udelay(ACA_ENABLE_COMPLETE_TIME); |
| |
| if (phy_meson8b_usb2_read(priv, REG_ADP_BC) & |
| REG_ADP_BC_ACA_PIN_FLOAT) { |
| dev_warn(&phy->dev, "USB ID detect failed!\n"); |
| clk_disable_unprepare(priv->clk_usb); |
| clk_disable_unprepare(priv->clk_usb_general); |
| return -EINVAL; |
| } |
| } |
| |
| return 0; |
| } |
| |
| static int phy_meson8b_usb2_power_off(struct phy *phy) |
| { |
| struct phy_meson8b_usb2_priv *priv = phy_get_drvdata(phy); |
| |
| clk_disable_unprepare(priv->clk_usb); |
| clk_disable_unprepare(priv->clk_usb_general); |
| |
| return 0; |
| } |
| |
| static const struct phy_ops phy_meson8b_usb2_ops = { |
| .power_on = phy_meson8b_usb2_power_on, |
| .power_off = phy_meson8b_usb2_power_off, |
| .owner = THIS_MODULE, |
| }; |
| |
| static int phy_meson8b_usb2_probe(struct platform_device *pdev) |
| { |
| struct phy_meson8b_usb2_priv *priv; |
| struct resource *res; |
| struct phy *phy; |
| struct phy_provider *phy_provider; |
| |
| priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL); |
| if (!priv) |
| return -ENOMEM; |
| |
| res = platform_get_resource(pdev, IORESOURCE_MEM, 0); |
| priv->regs = devm_ioremap_resource(&pdev->dev, res); |
| if (IS_ERR(priv->regs)) |
| return PTR_ERR(priv->regs); |
| |
| priv->clk_usb_general = devm_clk_get(&pdev->dev, "usb_general"); |
| if (IS_ERR(priv->clk_usb_general)) |
| return PTR_ERR(priv->clk_usb_general); |
| |
| priv->clk_usb = devm_clk_get(&pdev->dev, "usb"); |
| if (IS_ERR(priv->clk_usb)) |
| return PTR_ERR(priv->clk_usb); |
| |
| priv->reset = devm_reset_control_get_optional_shared(&pdev->dev, NULL); |
| if (PTR_ERR(priv->reset) == -EPROBE_DEFER) |
| return PTR_ERR(priv->reset); |
| |
| priv->dr_mode = of_usb_get_dr_mode_by_phy(pdev->dev.of_node, -1); |
| if (priv->dr_mode == USB_DR_MODE_UNKNOWN) { |
| dev_err(&pdev->dev, |
| "missing dual role configuration of the controller\n"); |
| return -EINVAL; |
| } |
| |
| phy = devm_phy_create(&pdev->dev, NULL, &phy_meson8b_usb2_ops); |
| if (IS_ERR(phy)) { |
| dev_err(&pdev->dev, "failed to create PHY\n"); |
| return PTR_ERR(phy); |
| } |
| |
| phy_set_drvdata(phy, priv); |
| |
| phy_provider = |
| devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate); |
| |
| return PTR_ERR_OR_ZERO(phy_provider); |
| } |
| |
| static const struct of_device_id phy_meson8b_usb2_of_match[] = { |
| { .compatible = "amlogic,meson8-usb2-phy", }, |
| { .compatible = "amlogic,meson8b-usb2-phy", }, |
| { .compatible = "amlogic,meson-gxbb-usb2-phy", }, |
| { }, |
| }; |
| MODULE_DEVICE_TABLE(of, phy_meson8b_usb2_of_match); |
| |
| static struct platform_driver phy_meson8b_usb2_driver = { |
| .probe = phy_meson8b_usb2_probe, |
| .driver = { |
| .name = "phy-meson-usb2", |
| .of_match_table = phy_meson8b_usb2_of_match, |
| }, |
| }; |
| module_platform_driver(phy_meson8b_usb2_driver); |
| |
| MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>"); |
| MODULE_DESCRIPTION("Meson8, Meson8b and GXBB USB2 PHY driver"); |
| MODULE_LICENSE("GPL"); |