| // SPDX-License-Identifier: GPL-2.0-only |
| /* |
| * (C) COPYRIGHT 2016 ARM Limited. All rights reserved. |
| * Author: Liviu Dudau <Liviu.Dudau@arm.com> |
| * |
| * ARM Mali DP500/DP550/DP650 driver (crtc operations) |
| */ |
| |
| #include <linux/clk.h> |
| #include <linux/pm_runtime.h> |
| |
| #include <video/videomode.h> |
| |
| #include <drm/drm_atomic.h> |
| #include <drm/drm_atomic_helper.h> |
| #include <drm/drm_crtc.h> |
| #include <drm/drm_print.h> |
| #include <drm/drm_probe_helper.h> |
| #include <drm/drm_vblank.h> |
| |
| #include "malidp_drv.h" |
| #include "malidp_hw.h" |
| |
| static enum drm_mode_status malidp_crtc_mode_valid(struct drm_crtc *crtc, |
| const struct drm_display_mode *mode) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| |
| /* |
| * check that the hardware can drive the required clock rate, |
| * but skip the check if the clock is meant to be disabled (req_rate = 0) |
| */ |
| long rate, req_rate = mode->crtc_clock * 1000; |
| |
| if (req_rate) { |
| rate = clk_round_rate(hwdev->pxlclk, req_rate); |
| if (rate != req_rate) { |
| DRM_DEBUG_DRIVER("pxlclk doesn't support %ld Hz\n", |
| req_rate); |
| return MODE_NOCLOCK; |
| } |
| } |
| |
| return MODE_OK; |
| } |
| |
| static void malidp_crtc_atomic_enable(struct drm_crtc *crtc, |
| struct drm_crtc_state *old_state) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| struct videomode vm; |
| int err = pm_runtime_get_sync(crtc->dev->dev); |
| |
| if (err < 0) { |
| DRM_DEBUG_DRIVER("Failed to enable runtime power management: %d\n", err); |
| return; |
| } |
| |
| drm_display_mode_to_videomode(&crtc->state->adjusted_mode, &vm); |
| clk_prepare_enable(hwdev->pxlclk); |
| |
| /* We rely on firmware to set mclk to a sensible level. */ |
| clk_set_rate(hwdev->pxlclk, crtc->state->adjusted_mode.crtc_clock * 1000); |
| |
| hwdev->hw->modeset(hwdev, &vm); |
| hwdev->hw->leave_config_mode(hwdev); |
| drm_crtc_vblank_on(crtc); |
| } |
| |
| static void malidp_crtc_atomic_disable(struct drm_crtc *crtc, |
| struct drm_crtc_state *old_state) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| int err; |
| |
| /* always disable planes on the CRTC that is being turned off */ |
| drm_atomic_helper_disable_planes_on_crtc(old_state, false); |
| |
| drm_crtc_vblank_off(crtc); |
| hwdev->hw->enter_config_mode(hwdev); |
| |
| clk_disable_unprepare(hwdev->pxlclk); |
| |
| err = pm_runtime_put(crtc->dev->dev); |
| if (err < 0) { |
| DRM_DEBUG_DRIVER("Failed to disable runtime power management: %d\n", err); |
| } |
| } |
| |
| static const struct gamma_curve_segment { |
| u16 start; |
| u16 end; |
| } segments[MALIDP_COEFFTAB_NUM_COEFFS] = { |
| /* sector 0 */ |
| { 0, 0 }, { 1, 1 }, { 2, 2 }, { 3, 3 }, |
| { 4, 4 }, { 5, 5 }, { 6, 6 }, { 7, 7 }, |
| { 8, 8 }, { 9, 9 }, { 10, 10 }, { 11, 11 }, |
| { 12, 12 }, { 13, 13 }, { 14, 14 }, { 15, 15 }, |
| /* sector 1 */ |
| { 16, 19 }, { 20, 23 }, { 24, 27 }, { 28, 31 }, |
| /* sector 2 */ |
| { 32, 39 }, { 40, 47 }, { 48, 55 }, { 56, 63 }, |
| /* sector 3 */ |
| { 64, 79 }, { 80, 95 }, { 96, 111 }, { 112, 127 }, |
| /* sector 4 */ |
| { 128, 159 }, { 160, 191 }, { 192, 223 }, { 224, 255 }, |
| /* sector 5 */ |
| { 256, 319 }, { 320, 383 }, { 384, 447 }, { 448, 511 }, |
| /* sector 6 */ |
| { 512, 639 }, { 640, 767 }, { 768, 895 }, { 896, 1023 }, |
| { 1024, 1151 }, { 1152, 1279 }, { 1280, 1407 }, { 1408, 1535 }, |
| { 1536, 1663 }, { 1664, 1791 }, { 1792, 1919 }, { 1920, 2047 }, |
| { 2048, 2175 }, { 2176, 2303 }, { 2304, 2431 }, { 2432, 2559 }, |
| { 2560, 2687 }, { 2688, 2815 }, { 2816, 2943 }, { 2944, 3071 }, |
| { 3072, 3199 }, { 3200, 3327 }, { 3328, 3455 }, { 3456, 3583 }, |
| { 3584, 3711 }, { 3712, 3839 }, { 3840, 3967 }, { 3968, 4095 }, |
| }; |
| |
| #define DE_COEFTAB_DATA(a, b) ((((a) & 0xfff) << 16) | (((b) & 0xfff))) |
| |
| static void malidp_generate_gamma_table(struct drm_property_blob *lut_blob, |
| u32 coeffs[MALIDP_COEFFTAB_NUM_COEFFS]) |
| { |
| struct drm_color_lut *lut = (struct drm_color_lut *)lut_blob->data; |
| int i; |
| |
| for (i = 0; i < MALIDP_COEFFTAB_NUM_COEFFS; ++i) { |
| u32 a, b, delta_in, out_start, out_end; |
| |
| delta_in = segments[i].end - segments[i].start; |
| /* DP has 12-bit internal precision for its LUTs. */ |
| out_start = drm_color_lut_extract(lut[segments[i].start].green, |
| 12); |
| out_end = drm_color_lut_extract(lut[segments[i].end].green, 12); |
| a = (delta_in == 0) ? 0 : ((out_end - out_start) * 256) / delta_in; |
| b = out_start; |
| coeffs[i] = DE_COEFTAB_DATA(a, b); |
| } |
| } |
| |
| /* |
| * Check if there is a new gamma LUT and if it is of an acceptable size. Also, |
| * reject any LUTs that use distinct red, green, and blue curves. |
| */ |
| static int malidp_crtc_atomic_check_gamma(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct malidp_crtc_state *mc = to_malidp_crtc_state(state); |
| struct drm_color_lut *lut; |
| size_t lut_size; |
| int i; |
| |
| if (!state->color_mgmt_changed || !state->gamma_lut) |
| return 0; |
| |
| if (crtc->state->gamma_lut && |
| (crtc->state->gamma_lut->base.id == state->gamma_lut->base.id)) |
| return 0; |
| |
| if (state->gamma_lut->length % sizeof(struct drm_color_lut)) |
| return -EINVAL; |
| |
| lut_size = state->gamma_lut->length / sizeof(struct drm_color_lut); |
| if (lut_size != MALIDP_GAMMA_LUT_SIZE) |
| return -EINVAL; |
| |
| lut = (struct drm_color_lut *)state->gamma_lut->data; |
| for (i = 0; i < lut_size; ++i) |
| if (!((lut[i].red == lut[i].green) && |
| (lut[i].red == lut[i].blue))) |
| return -EINVAL; |
| |
| if (!state->mode_changed) { |
| int ret; |
| |
| state->mode_changed = true; |
| /* |
| * Kerneldoc for drm_atomic_helper_check_modeset mandates that |
| * it be invoked when the driver sets ->mode_changed. Since |
| * changing the gamma LUT doesn't depend on any external |
| * resources, it is safe to call it only once. |
| */ |
| ret = drm_atomic_helper_check_modeset(crtc->dev, state->state); |
| if (ret) |
| return ret; |
| } |
| |
| malidp_generate_gamma_table(state->gamma_lut, mc->gamma_coeffs); |
| return 0; |
| } |
| |
| /* |
| * Check if there is a new CTM and if it contains valid input. Valid here means |
| * that the number is inside the representable range for a Q3.12 number, |
| * excluding truncating the fractional part of the input data. |
| * |
| * The COLORADJ registers can be changed atomically. |
| */ |
| static int malidp_crtc_atomic_check_ctm(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct malidp_crtc_state *mc = to_malidp_crtc_state(state); |
| struct drm_color_ctm *ctm; |
| int i; |
| |
| if (!state->color_mgmt_changed) |
| return 0; |
| |
| if (!state->ctm) |
| return 0; |
| |
| if (crtc->state->ctm && (crtc->state->ctm->base.id == |
| state->ctm->base.id)) |
| return 0; |
| |
| /* |
| * The size of the ctm is checked in |
| * drm_atomic_replace_property_blob_from_id. |
| */ |
| ctm = (struct drm_color_ctm *)state->ctm->data; |
| for (i = 0; i < ARRAY_SIZE(ctm->matrix); ++i) { |
| /* Convert from S31.32 to Q3.12. */ |
| s64 val = ctm->matrix[i]; |
| u32 mag = ((((u64)val) & ~BIT_ULL(63)) >> 20) & |
| GENMASK_ULL(14, 0); |
| |
| /* |
| * Convert to 2s complement and check the destination's top bit |
| * for overflow. NB: Can't check before converting or it'd |
| * incorrectly reject the case: |
| * sign == 1 |
| * mag == 0x2000 |
| */ |
| if (val & BIT_ULL(63)) |
| mag = ~mag + 1; |
| if (!!(val & BIT_ULL(63)) != !!(mag & BIT(14))) |
| return -EINVAL; |
| mc->coloradj_coeffs[i] = mag; |
| } |
| |
| return 0; |
| } |
| |
| static int malidp_crtc_atomic_check_scaling(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| struct malidp_crtc_state *cs = to_malidp_crtc_state(state); |
| struct malidp_se_config *s = &cs->scaler_config; |
| struct drm_plane *plane; |
| struct videomode vm; |
| const struct drm_plane_state *pstate; |
| u32 h_upscale_factor = 0; /* U16.16 */ |
| u32 v_upscale_factor = 0; /* U16.16 */ |
| u8 scaling = cs->scaled_planes_mask; |
| int ret; |
| |
| if (!scaling) { |
| s->scale_enable = false; |
| goto mclk_calc; |
| } |
| |
| /* The scaling engine can only handle one plane at a time. */ |
| if (scaling & (scaling - 1)) |
| return -EINVAL; |
| |
| drm_atomic_crtc_state_for_each_plane_state(plane, pstate, state) { |
| struct malidp_plane *mp = to_malidp_plane(plane); |
| u32 phase; |
| |
| if (!(mp->layer->id & scaling)) |
| continue; |
| |
| /* |
| * Convert crtc_[w|h] to U32.32, then divide by U16.16 src_[w|h] |
| * to get the U16.16 result. |
| */ |
| h_upscale_factor = div_u64((u64)pstate->crtc_w << 32, |
| pstate->src_w); |
| v_upscale_factor = div_u64((u64)pstate->crtc_h << 32, |
| pstate->src_h); |
| |
| s->enhancer_enable = ((h_upscale_factor >> 16) >= 2 || |
| (v_upscale_factor >> 16) >= 2); |
| |
| if (pstate->rotation & MALIDP_ROTATED_MASK) { |
| s->input_w = pstate->src_h >> 16; |
| s->input_h = pstate->src_w >> 16; |
| } else { |
| s->input_w = pstate->src_w >> 16; |
| s->input_h = pstate->src_h >> 16; |
| } |
| |
| s->output_w = pstate->crtc_w; |
| s->output_h = pstate->crtc_h; |
| |
| #define SE_N_PHASE 4 |
| #define SE_SHIFT_N_PHASE 12 |
| /* Calculate initial_phase and delta_phase for horizontal. */ |
| phase = s->input_w; |
| s->h_init_phase = |
| ((phase << SE_N_PHASE) / s->output_w + 1) / 2; |
| |
| phase = s->input_w; |
| phase <<= (SE_SHIFT_N_PHASE + SE_N_PHASE); |
| s->h_delta_phase = phase / s->output_w; |
| |
| /* Same for vertical. */ |
| phase = s->input_h; |
| s->v_init_phase = |
| ((phase << SE_N_PHASE) / s->output_h + 1) / 2; |
| |
| phase = s->input_h; |
| phase <<= (SE_SHIFT_N_PHASE + SE_N_PHASE); |
| s->v_delta_phase = phase / s->output_h; |
| #undef SE_N_PHASE |
| #undef SE_SHIFT_N_PHASE |
| s->plane_src_id = mp->layer->id; |
| } |
| |
| s->scale_enable = true; |
| s->hcoeff = malidp_se_select_coeffs(h_upscale_factor); |
| s->vcoeff = malidp_se_select_coeffs(v_upscale_factor); |
| |
| mclk_calc: |
| drm_display_mode_to_videomode(&state->adjusted_mode, &vm); |
| ret = hwdev->hw->se_calc_mclk(hwdev, s, &vm); |
| if (ret < 0) |
| return -EINVAL; |
| return 0; |
| } |
| |
| static int malidp_crtc_atomic_check(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| struct drm_plane *plane; |
| const struct drm_plane_state *pstate; |
| u32 rot_mem_free, rot_mem_usable; |
| int rotated_planes = 0; |
| int ret; |
| |
| /* |
| * check if there is enough rotation memory available for planes |
| * that need 90° and 270° rotion or planes that are compressed. |
| * Each plane has set its required memory size in the ->plane_check() |
| * callback, here we only make sure that the sums are less that the |
| * total usable memory. |
| * |
| * The rotation memory allocation algorithm (for each plane): |
| * a. If no more rotated or compressed planes exist, all remaining |
| * rotate memory in the bank is available for use by the plane. |
| * b. If other rotated or compressed planes exist, and plane's |
| * layer ID is DE_VIDEO1, it can use all the memory from first bank |
| * if secondary rotation memory bank is available, otherwise it can |
| * use up to half the bank's memory. |
| * c. If other rotated or compressed planes exist, and plane's layer ID |
| * is not DE_VIDEO1, it can use half of the available memory. |
| * |
| * Note: this algorithm assumes that the order in which the planes are |
| * checked always has DE_VIDEO1 plane first in the list if it is |
| * rotated. Because that is how we create the planes in the first |
| * place, under current DRM version things work, but if ever the order |
| * in which drm_atomic_crtc_state_for_each_plane() iterates over planes |
| * changes, we need to pre-sort the planes before validation. |
| */ |
| |
| /* first count the number of rotated planes */ |
| drm_atomic_crtc_state_for_each_plane_state(plane, pstate, state) { |
| struct drm_framebuffer *fb = pstate->fb; |
| |
| if ((pstate->rotation & MALIDP_ROTATED_MASK) || fb->modifier) |
| rotated_planes++; |
| } |
| |
| rot_mem_free = hwdev->rotation_memory[0]; |
| /* |
| * if we have more than 1 plane using rotation memory, use the second |
| * block of rotation memory as well |
| */ |
| if (rotated_planes > 1) |
| rot_mem_free += hwdev->rotation_memory[1]; |
| |
| /* now validate the rotation memory requirements */ |
| drm_atomic_crtc_state_for_each_plane_state(plane, pstate, state) { |
| struct malidp_plane *mp = to_malidp_plane(plane); |
| struct malidp_plane_state *ms = to_malidp_plane_state(pstate); |
| struct drm_framebuffer *fb = pstate->fb; |
| |
| if ((pstate->rotation & MALIDP_ROTATED_MASK) || fb->modifier) { |
| /* process current plane */ |
| rotated_planes--; |
| |
| if (!rotated_planes) { |
| /* no more rotated planes, we can use what's left */ |
| rot_mem_usable = rot_mem_free; |
| } else { |
| if ((mp->layer->id != DE_VIDEO1) || |
| (hwdev->rotation_memory[1] == 0)) |
| rot_mem_usable = rot_mem_free / 2; |
| else |
| rot_mem_usable = hwdev->rotation_memory[0]; |
| } |
| |
| rot_mem_free -= rot_mem_usable; |
| |
| if (ms->rotmem_size > rot_mem_usable) |
| return -EINVAL; |
| } |
| } |
| |
| /* If only the writeback routing has changed, we don't need a modeset */ |
| if (state->connectors_changed) { |
| u32 old_mask = crtc->state->connector_mask; |
| u32 new_mask = state->connector_mask; |
| |
| if ((old_mask ^ new_mask) == |
| (1 << drm_connector_index(&malidp->mw_connector.base))) |
| state->connectors_changed = false; |
| } |
| |
| ret = malidp_crtc_atomic_check_gamma(crtc, state); |
| ret = ret ? ret : malidp_crtc_atomic_check_ctm(crtc, state); |
| ret = ret ? ret : malidp_crtc_atomic_check_scaling(crtc, state); |
| |
| return ret; |
| } |
| |
| static const struct drm_crtc_helper_funcs malidp_crtc_helper_funcs = { |
| .mode_valid = malidp_crtc_mode_valid, |
| .atomic_check = malidp_crtc_atomic_check, |
| .atomic_enable = malidp_crtc_atomic_enable, |
| .atomic_disable = malidp_crtc_atomic_disable, |
| }; |
| |
| static struct drm_crtc_state *malidp_crtc_duplicate_state(struct drm_crtc *crtc) |
| { |
| struct malidp_crtc_state *state, *old_state; |
| |
| if (WARN_ON(!crtc->state)) |
| return NULL; |
| |
| old_state = to_malidp_crtc_state(crtc->state); |
| state = kmalloc(sizeof(*state), GFP_KERNEL); |
| if (!state) |
| return NULL; |
| |
| __drm_atomic_helper_crtc_duplicate_state(crtc, &state->base); |
| memcpy(state->gamma_coeffs, old_state->gamma_coeffs, |
| sizeof(state->gamma_coeffs)); |
| memcpy(state->coloradj_coeffs, old_state->coloradj_coeffs, |
| sizeof(state->coloradj_coeffs)); |
| memcpy(&state->scaler_config, &old_state->scaler_config, |
| sizeof(state->scaler_config)); |
| state->scaled_planes_mask = 0; |
| |
| return &state->base; |
| } |
| |
| static void malidp_crtc_destroy_state(struct drm_crtc *crtc, |
| struct drm_crtc_state *state) |
| { |
| struct malidp_crtc_state *mali_state = NULL; |
| |
| if (state) { |
| mali_state = to_malidp_crtc_state(state); |
| __drm_atomic_helper_crtc_destroy_state(state); |
| } |
| |
| kfree(mali_state); |
| } |
| |
| static void malidp_crtc_reset(struct drm_crtc *crtc) |
| { |
| struct malidp_crtc_state *state = |
| kzalloc(sizeof(*state), GFP_KERNEL); |
| |
| if (crtc->state) |
| malidp_crtc_destroy_state(crtc, crtc->state); |
| |
| __drm_atomic_helper_crtc_reset(crtc, &state->base); |
| } |
| |
| static int malidp_crtc_enable_vblank(struct drm_crtc *crtc) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| |
| malidp_hw_enable_irq(hwdev, MALIDP_DE_BLOCK, |
| hwdev->hw->map.de_irq_map.vsync_irq); |
| return 0; |
| } |
| |
| static void malidp_crtc_disable_vblank(struct drm_crtc *crtc) |
| { |
| struct malidp_drm *malidp = crtc_to_malidp_device(crtc); |
| struct malidp_hw_device *hwdev = malidp->dev; |
| |
| malidp_hw_disable_irq(hwdev, MALIDP_DE_BLOCK, |
| hwdev->hw->map.de_irq_map.vsync_irq); |
| } |
| |
| static const struct drm_crtc_funcs malidp_crtc_funcs = { |
| .gamma_set = drm_atomic_helper_legacy_gamma_set, |
| .destroy = drm_crtc_cleanup, |
| .set_config = drm_atomic_helper_set_config, |
| .page_flip = drm_atomic_helper_page_flip, |
| .reset = malidp_crtc_reset, |
| .atomic_duplicate_state = malidp_crtc_duplicate_state, |
| .atomic_destroy_state = malidp_crtc_destroy_state, |
| .enable_vblank = malidp_crtc_enable_vblank, |
| .disable_vblank = malidp_crtc_disable_vblank, |
| }; |
| |
| int malidp_crtc_init(struct drm_device *drm) |
| { |
| struct malidp_drm *malidp = drm->dev_private; |
| struct drm_plane *primary = NULL, *plane; |
| int ret; |
| |
| ret = malidp_de_planes_init(drm); |
| if (ret < 0) { |
| DRM_ERROR("Failed to initialise planes\n"); |
| return ret; |
| } |
| |
| drm_for_each_plane(plane, drm) { |
| if (plane->type == DRM_PLANE_TYPE_PRIMARY) { |
| primary = plane; |
| break; |
| } |
| } |
| |
| if (!primary) { |
| DRM_ERROR("no primary plane found\n"); |
| return -EINVAL; |
| } |
| |
| ret = drm_crtc_init_with_planes(drm, &malidp->crtc, primary, NULL, |
| &malidp_crtc_funcs, NULL); |
| if (ret) |
| return ret; |
| |
| drm_crtc_helper_add(&malidp->crtc, &malidp_crtc_helper_funcs); |
| drm_mode_crtc_set_gamma_size(&malidp->crtc, MALIDP_GAMMA_LUT_SIZE); |
| /* No inverse-gamma: it is per-plane. */ |
| drm_crtc_enable_color_mgmt(&malidp->crtc, 0, true, MALIDP_GAMMA_LUT_SIZE); |
| |
| malidp_se_set_enh_coeffs(malidp->dev); |
| |
| return 0; |
| } |