blob: 08b0b9fbcbc9a3621e104429a8a42bf4dcad4c35 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Copyright (c) 2020 Engicam srl
* Copyright (c) 2020 Amarula Solutions
* Copyright (c) 2020 Amarula Solutions(India)
*/
/ {
vcc5v0_sys: vcc5v0-sys {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_sys"; /* +5V */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
};
sdio_pwrseq: sdio-pwrseq {
compatible = "mmc-pwrseq-simple";
clocks = <&xin32k>;
clock-names = "ext_clock";
post-power-on-delay-ms = <80>;
pinctrl-names = "default";
pinctrl-0 = <&wifi_enable_h>;
};
vcc3v3_btreg: vcc3v3-btreg {
compatible = "regulator-gpio";
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&bt_enable_h>;
regulator-name = "btreg-gpio-supply";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
states = <3300000 0x0>;
};
vcc3v3_rf_aux_mod: vcc3v3-rf-aux-mod {
compatible = "regulator-fixed";
regulator-name = "vcc3v3_rf_aux_mod";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
regulator-boot-on;
vin-supply = <&vcc5v0_sys>;
};
xin32k: xin32k {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <32768>;
clock-output-names = "xin32k";
};
};
&sdio {
#address-cells = <1>;
#size-cells = <0>;
bus-width = <4>;
clock-frequency = <50000000>;
cap-sdio-irq;
cap-sd-highspeed;
keep-power-in-suspend;
mmc-pwrseq = <&sdio_pwrseq>;
non-removable;
sd-uhs-sdr104;
status = "okay";
brcmf: wifi@1 {
compatible = "brcm,bcm4329-fmac";
reg = <1>;
};
};
&gmac {
clock_in_out = "output";
phy-supply = <&vcc_3v3>; /* +3V3_SOM */
snps,reset-active-low;
snps,reset-delays-us = <0 50000 50000>;
snps,reset-gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&pwm0 {
status = "okay";
};
&sdmmc {
cap-sd-highspeed;
card-detect-delay = <800>;
vmmc-supply = <&vcc_3v3>; /* +3V3_SOM */
vqmmc-supply = <&vcc_3v3>;
status = "okay";
};
&u2phy {
status = "okay";
u2phy_host: host-port {
status = "okay";
};
u2phy_otg: otg-port {
status = "okay";
};
};
&uart2 {
pinctrl-0 = <&uart2m1_xfer>;
status = "okay";
};
&usb20_otg {
status = "okay";
};
&usb_host0_ehci {
status = "okay";
};
&usb_host0_ohci {
status = "okay";
};