| #include "qcom-msm8974pro.dtsi" |
| #include "qcom-pm8841.dtsi" |
| #include "qcom-pm8941.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| |
| / { |
| model = "Sony Xperia Z2 Tablet"; |
| compatible = "sony,xperia-castor", "qcom,msm8974"; |
| |
| aliases { |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0:115200n8"; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| input-name = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_pin_a>; |
| |
| volume-down { |
| label = "volume_down"; |
| gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| |
| camera-snapshot { |
| label = "camera_snapshot"; |
| gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_CAMERA>; |
| }; |
| |
| camera-focus { |
| label = "camera_focus"; |
| gpios = <&pm8941_gpios 4 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_CAMERA_FOCUS>; |
| }; |
| |
| volume-up { |
| label = "volume_up"; |
| gpios = <&pm8941_gpios 5 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| }; |
| |
| smd { |
| rpm { |
| rpm_requests { |
| pm8941-regulators { |
| vdd_l1_l3-supply = <&pm8941_s1>; |
| vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; |
| vdd_l4_l11-supply = <&pm8941_s1>; |
| vdd_l5_l7-supply = <&pm8941_s2>; |
| vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; |
| vdd_l9_l10_l17_l22-supply = <&vreg_boost>; |
| vdd_l13_l20_l23_l24-supply = <&vreg_boost>; |
| vdd_l21-supply = <&vreg_boost>; |
| |
| s1 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1300000>; |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| s2 { |
| regulator-min-microvolt = <2150000>; |
| regulator-max-microvolt = <2150000>; |
| regulator-boot-on; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| regulator-always-on; |
| regulator-boot-on; |
| |
| regulator-system-load = <154000>; |
| }; |
| |
| s4 { |
| regulator-min-microvolt = <5000000>; |
| regulator-max-microvolt = <5000000>; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l3 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l8 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l9 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l11 { |
| regulator-min-microvolt = <1300000>; |
| regulator-max-microvolt = <1350000>; |
| }; |
| |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| |
| regulator-always-on; |
| regulator-boot-on; |
| }; |
| |
| l13 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l15 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| l16 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| l17 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| |
| l18 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l19 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l20 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-allow-set-load; |
| regulator-boot-on; |
| regulator-allow-set-load; |
| regulator-system-load = <500000>; |
| }; |
| |
| l21 { |
| regulator-min-microvolt = <2950000>; |
| regulator-max-microvolt = <2950000>; |
| |
| regulator-boot-on; |
| }; |
| |
| l22 { |
| regulator-min-microvolt = <3000000>; |
| regulator-max-microvolt = <3000000>; |
| }; |
| |
| l23 { |
| regulator-min-microvolt = <2800000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| l24 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| |
| regulator-boot-on; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| vreg_bl_vddio: lcd-backlight-vddio { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_bl_vddio"; |
| regulator-min-microvolt = <3150000>; |
| regulator-max-microvolt = <3150000>; |
| |
| gpio = <&msmgpio 69 0>; |
| enable-active-high; |
| |
| vin-supply = <&pm8941_s3>; |
| startup-delay-us = <70000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_backlight_en_pin_a>; |
| }; |
| |
| vreg_vsp: lcd-dcdc-regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "vreg_vsp"; |
| regulator-min-microvolt = <5600000>; |
| regulator-max-microvolt = <5600000>; |
| |
| gpio = <&pm8941_gpios 20 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&lcd_dcdc_en_pin_a>; |
| }; |
| |
| vreg_wlan: wlan-regulator { |
| compatible = "regulator-fixed"; |
| |
| regulator-name = "wl-reg"; |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| |
| gpio = <&pm8941_gpios 18 GPIO_ACTIVE_HIGH>; |
| enable-active-high; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_regulator_pin>; |
| }; |
| }; |
| |
| &soc { |
| sdhci@f9824900 { |
| status = "ok"; |
| |
| vmmc-supply = <&pm8941_l20>; |
| vqmmc-supply = <&pm8941_s3>; |
| |
| bus-width = <8>; |
| non-removable; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc1_pin_a>; |
| }; |
| |
| sdhci@f9864900 { |
| status = "ok"; |
| |
| max-frequency = <100000000>; |
| non-removable; |
| vmmc-supply = <&vreg_wlan>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc3_pin_a>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| bcrmf@1 { |
| compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac"; |
| reg = <1>; |
| |
| brcm,drive-strength = <10>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&wlan_sleep_clk_pin>; |
| }; |
| }; |
| |
| sdhci@f98a4900 { |
| status = "ok"; |
| |
| bus-width = <4>; |
| |
| vmmc-supply = <&pm8941_l21>; |
| vqmmc-supply = <&pm8941_l13>; |
| |
| cd-gpios = <&msmgpio 62 GPIO_ACTIVE_LOW>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>; |
| }; |
| |
| serial@f991e000 { |
| status = "ok"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&blsp1_uart2_pin_a>; |
| }; |
| |
| usb@f9a55000 { |
| status = "ok"; |
| |
| phys = <&usb_hs1_phy>; |
| phy-select = <&tcsr 0xb000 0>; |
| extcon = <&smbb>, <&usb_id>; |
| vbus-supply = <&chg_otg>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| ulpi { |
| phy@a { |
| status = "ok"; |
| |
| v1p8-supply = <&pm8941_l6>; |
| v3p3-supply = <&pm8941_l24>; |
| |
| extcon = <&smbb>; |
| qcom,init-seq = /bits/ 8 <0x1 0x64>; |
| }; |
| }; |
| }; |
| |
| pinctrl@fd510000 { |
| blsp1_uart2_pin_a: blsp1-uart2-pin-active { |
| rx { |
| pins = "gpio5"; |
| function = "blsp_uart2"; |
| |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| tx { |
| pins = "gpio4"; |
| function = "blsp_uart2"; |
| |
| drive-strength = <4>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c8_pins: i2c8 { |
| mux { |
| pins = "gpio47", "gpio48"; |
| function = "blsp_i2c8"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| i2c11_pins: i2c11 { |
| mux { |
| pins = "gpio83", "gpio84"; |
| function = "blsp_i2c11"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| lcd_backlight_en_pin_a: lcd-backlight-vddio { |
| pins = "gpio69"; |
| drive-strength = <10>; |
| output-low; |
| bias-disable; |
| }; |
| |
| sdhc1_pin_a: sdhc1-pin-active { |
| clk { |
| pins = "sdc1_clk"; |
| drive-strength = <16>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc1_cmd", "sdc1_data"; |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc2_cd_pin_a: sdhc2-cd-pin-active { |
| pins = "gpio62"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| |
| sdhc2_pin_a: sdhc2-pin-active { |
| clk { |
| pins = "sdc2_clk"; |
| drive-strength = <6>; |
| bias-disable; |
| }; |
| |
| cmd-data { |
| pins = "sdc2_cmd", "sdc2_data"; |
| drive-strength = <6>; |
| bias-pull-up; |
| }; |
| }; |
| |
| sdhc3_pin_a: sdhc3-pin-active { |
| clk { |
| pins = "gpio40"; |
| function = "sdc3"; |
| |
| drive-strength = <10>; |
| bias-disable; |
| }; |
| |
| cmd { |
| pins = "gpio39"; |
| function = "sdc3"; |
| |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| |
| data { |
| pins = "gpio35", "gpio36", "gpio37", "gpio38"; |
| function = "sdc3"; |
| |
| drive-strength = <10>; |
| bias-pull-up; |
| }; |
| }; |
| |
| ts_int_pin: synaptics { |
| pin { |
| pins = "gpio86"; |
| function = "gpio"; |
| |
| drive-strength = <2>; |
| bias-disable; |
| input-enable; |
| }; |
| }; |
| }; |
| |
| i2c@f9964000 { |
| status = "ok"; |
| |
| clock-frequency = <355000>; |
| qcom,src-freq = <50000000>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c8_pins>; |
| |
| synaptics@2c { |
| compatible = "syna,rmi-i2c"; |
| reg = <0x2c>; |
| |
| interrupt-parent = <&msmgpio>; |
| interrupts = <86 IRQ_TYPE_EDGE_FALLING>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vdd-supply = <&pm8941_l22>; |
| vio-supply = <&pm8941_lvs3>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&ts_int_pin>; |
| |
| rmi-f01@1 { |
| reg = <0x1>; |
| syna,nosleep = <1>; |
| }; |
| |
| rmi-f11@11 { |
| reg = <0x11>; |
| syna,f11-flip-x = <1>; |
| syna,sensor-type = <1>; |
| }; |
| }; |
| }; |
| |
| i2c@f9967000 { |
| status = "ok"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&i2c11_pins>; |
| clock-frequency = <355000>; |
| qcom,src-freq = <50000000>; |
| |
| lp8566_wled: backlight@2c { |
| compatible = "ti,lp8556"; |
| reg = <0x2c>; |
| power-supply = <&vreg_bl_vddio>; |
| |
| bl-name = "backlight"; |
| dev-ctrl = /bits/ 8 <0x05>; |
| init-brt = /bits/ 8 <0x3f>; |
| rom_a0h { |
| rom-addr = /bits/ 8 <0xa0>; |
| rom-val = /bits/ 8 <0xff>; |
| }; |
| rom_a1h { |
| rom-addr = /bits/ 8 <0xa1>; |
| rom-val = /bits/ 8 <0x3f>; |
| }; |
| rom_a2h { |
| rom-addr = /bits/ 8 <0xa2>; |
| rom-val = /bits/ 8 <0x20>; |
| }; |
| rom_a3h { |
| rom-addr = /bits/ 8 <0xa3>; |
| rom-val = /bits/ 8 <0x5e>; |
| }; |
| rom_a4h { |
| rom-addr = /bits/ 8 <0xa4>; |
| rom-val = /bits/ 8 <0x02>; |
| }; |
| rom_a5h { |
| rom-addr = /bits/ 8 <0xa5>; |
| rom-val = /bits/ 8 <0x04>; |
| }; |
| rom_a6h { |
| rom-addr = /bits/ 8 <0xa6>; |
| rom-val = /bits/ 8 <0x80>; |
| }; |
| rom_a7h { |
| rom-addr = /bits/ 8 <0xa7>; |
| rom-val = /bits/ 8 <0xf7>; |
| }; |
| rom_a9h { |
| rom-addr = /bits/ 8 <0xa9>; |
| rom-val = /bits/ 8 <0x80>; |
| }; |
| rom_aah { |
| rom-addr = /bits/ 8 <0xaa>; |
| rom-val = /bits/ 8 <0x0f>; |
| }; |
| rom_aeh { |
| rom-addr = /bits/ 8 <0xae>; |
| rom-val = /bits/ 8 <0x0f>; |
| }; |
| }; |
| }; |
| }; |
| |
| &spmi_bus { |
| pm8941@0 { |
| charger@1000 { |
| qcom,fast-charge-safe-current = <1500000>; |
| qcom,fast-charge-current-limit = <1500000>; |
| qcom,dc-current-limit = <1800000>; |
| qcom,fast-charge-safe-voltage = <4400000>; |
| qcom,fast-charge-high-threshold-voltage = <4350000>; |
| qcom,fast-charge-low-threshold-voltage = <3400000>; |
| qcom,auto-recharge-threshold-voltage = <4200000>; |
| qcom,minimum-input-voltage = <4300000>; |
| }; |
| |
| gpios@c000 { |
| gpio_keys_pin_a: gpio-keys-active { |
| pins = "gpio2", "gpio5"; |
| function = "normal"; |
| |
| bias-pull-up; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_sleep_clk_pin: wl-sleep-clk { |
| pins = "gpio17"; |
| function = "func2"; |
| |
| output-high; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| wlan_regulator_pin: wl-reg-active { |
| pins = "gpio18"; |
| function = "normal"; |
| |
| bias-disable; |
| power-source = <PM8941_GPIO_S3>; |
| }; |
| |
| lcd_dcdc_en_pin_a: lcd-dcdc-en-active { |
| pins = "gpio20"; |
| function = "normal"; |
| |
| bias-disable; |
| power-source = <PM8941_GPIO_S3>; |
| input-disable; |
| output-low; |
| }; |
| |
| }; |
| |
| coincell@2800 { |
| status = "ok"; |
| qcom,rset-ohms = <2100>; |
| qcom,vset-millivolts = <3000>; |
| }; |
| }; |
| }; |
