| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2020 MaxLinear, Inc. |
| * |
| * This driver is a hardware monitoring driver for PVT controller |
| * (MR75203) which is used to configure & control Moortec embedded |
| * analog IP to enable multiple embedded temperature sensor(TS), |
| * voltage monitor(VM) & process detector(PD) modules. |
| */ |
| #include <linux/bits.h> |
| #include <linux/clk.h> |
| #include <linux/hwmon.h> |
| #include <linux/module.h> |
| #include <linux/mod_devicetable.h> |
| #include <linux/mutex.h> |
| #include <linux/platform_device.h> |
| #include <linux/property.h> |
| #include <linux/regmap.h> |
| #include <linux/reset.h> |
| #include <linux/units.h> |
| |
| /* PVT Common register */ |
| #define PVT_IP_CONFIG 0x04 |
| #define TS_NUM_MSK GENMASK(4, 0) |
| #define TS_NUM_SFT 0 |
| #define PD_NUM_MSK GENMASK(12, 8) |
| #define PD_NUM_SFT 8 |
| #define VM_NUM_MSK GENMASK(20, 16) |
| #define VM_NUM_SFT 16 |
| #define CH_NUM_MSK GENMASK(31, 24) |
| #define CH_NUM_SFT 24 |
| |
| /* Macro Common Register */ |
| #define CLK_SYNTH 0x00 |
| #define CLK_SYNTH_LO_SFT 0 |
| #define CLK_SYNTH_HI_SFT 8 |
| #define CLK_SYNTH_HOLD_SFT 16 |
| #define CLK_SYNTH_EN BIT(24) |
| #define CLK_SYS_CYCLES_MAX 514 |
| #define CLK_SYS_CYCLES_MIN 2 |
| |
| #define SDIF_DISABLE 0x04 |
| |
| #define SDIF_STAT 0x08 |
| #define SDIF_BUSY BIT(0) |
| #define SDIF_LOCK BIT(1) |
| |
| #define SDIF_W 0x0c |
| #define SDIF_PROG BIT(31) |
| #define SDIF_WRN_W BIT(27) |
| #define SDIF_WRN_R 0x00 |
| #define SDIF_ADDR_SFT 24 |
| |
| #define SDIF_HALT 0x10 |
| #define SDIF_CTRL 0x14 |
| #define SDIF_SMPL_CTRL 0x20 |
| |
| /* TS & PD Individual Macro Register */ |
| #define COM_REG_SIZE 0x40 |
| |
| #define SDIF_DONE(n) (COM_REG_SIZE + 0x14 + 0x40 * (n)) |
| #define SDIF_SMPL_DONE BIT(0) |
| |
| #define SDIF_DATA(n) (COM_REG_SIZE + 0x18 + 0x40 * (n)) |
| #define SAMPLE_DATA_MSK GENMASK(15, 0) |
| |
| #define HILO_RESET(n) (COM_REG_SIZE + 0x2c + 0x40 * (n)) |
| |
| /* VM Individual Macro Register */ |
| #define VM_COM_REG_SIZE 0x200 |
| #define VM_SDIF_DONE(n) (VM_COM_REG_SIZE + 0x34 + 0x200 * (n)) |
| #define VM_SDIF_DATA(n) (VM_COM_REG_SIZE + 0x40 + 0x200 * (n)) |
| |
| /* SDA Slave Register */ |
| #define IP_CTRL 0x00 |
| #define IP_RST_REL BIT(1) |
| #define IP_RUN_CONT BIT(3) |
| #define IP_AUTO BIT(8) |
| #define IP_VM_MODE BIT(10) |
| |
| #define IP_CFG 0x01 |
| #define CFG0_MODE_2 BIT(0) |
| #define CFG0_PARALLEL_OUT 0 |
| #define CFG0_12_BIT 0 |
| #define CFG1_VOL_MEAS_MODE 0 |
| #define CFG1_PARALLEL_OUT 0 |
| #define CFG1_14_BIT 0 |
| |
| #define IP_DATA 0x03 |
| |
| #define IP_POLL 0x04 |
| #define VM_CH_INIT BIT(20) |
| #define VM_CH_REQ BIT(21) |
| |
| #define IP_TMR 0x05 |
| #define POWER_DELAY_CYCLE_256 0x80 |
| #define POWER_DELAY_CYCLE_64 0x40 |
| |
| #define PVT_POLL_DELAY_US 20 |
| #define PVT_POLL_TIMEOUT_US 20000 |
| #define PVT_H_CONST 100000 |
| #define PVT_CAL5_CONST 2047 |
| #define PVT_G_CONST 40000 |
| #define PVT_CONV_BITS 10 |
| #define PVT_N_CONST 90 |
| #define PVT_R_CONST 245805 |
| |
| struct pvt_device { |
| struct regmap *c_map; |
| struct regmap *t_map; |
| struct regmap *p_map; |
| struct regmap *v_map; |
| struct clk *clk; |
| struct reset_control *rst; |
| u32 t_num; |
| u32 p_num; |
| u32 v_num; |
| u32 ip_freq; |
| u8 *vm_idx; |
| }; |
| |
| static umode_t pvt_is_visible(const void *data, enum hwmon_sensor_types type, |
| u32 attr, int channel) |
| { |
| switch (type) { |
| case hwmon_temp: |
| if (attr == hwmon_temp_input) |
| return 0444; |
| break; |
| case hwmon_in: |
| if (attr == hwmon_in_input) |
| return 0444; |
| break; |
| default: |
| break; |
| } |
| return 0; |
| } |
| |
| static int pvt_read_temp(struct device *dev, u32 attr, int channel, long *val) |
| { |
| struct pvt_device *pvt = dev_get_drvdata(dev); |
| struct regmap *t_map = pvt->t_map; |
| u32 stat, nbs; |
| int ret; |
| u64 tmp; |
| |
| switch (attr) { |
| case hwmon_temp_input: |
| ret = regmap_read_poll_timeout(t_map, SDIF_DONE(channel), |
| stat, stat & SDIF_SMPL_DONE, |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(t_map, SDIF_DATA(channel), &nbs); |
| if(ret < 0) |
| return ret; |
| |
| nbs &= SAMPLE_DATA_MSK; |
| |
| /* |
| * Convert the register value to |
| * degrees centigrade temperature |
| */ |
| tmp = nbs * PVT_H_CONST; |
| do_div(tmp, PVT_CAL5_CONST); |
| *val = tmp - PVT_G_CONST - pvt->ip_freq; |
| |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int pvt_read_in(struct device *dev, u32 attr, int channel, long *val) |
| { |
| struct pvt_device *pvt = dev_get_drvdata(dev); |
| struct regmap *v_map = pvt->v_map; |
| u32 n, stat; |
| u8 vm_idx; |
| int ret; |
| |
| if (channel >= pvt->v_num) |
| return -EINVAL; |
| |
| vm_idx = pvt->vm_idx[channel]; |
| |
| switch (attr) { |
| case hwmon_in_input: |
| ret = regmap_read_poll_timeout(v_map, VM_SDIF_DONE(vm_idx), |
| stat, stat & SDIF_SMPL_DONE, |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| ret = regmap_read(v_map, VM_SDIF_DATA(vm_idx), &n); |
| if(ret < 0) |
| return ret; |
| |
| n &= SAMPLE_DATA_MSK; |
| /* Convert the N bitstream count into voltage */ |
| *val = (PVT_N_CONST * n - PVT_R_CONST) >> PVT_CONV_BITS; |
| |
| return 0; |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static int pvt_read(struct device *dev, enum hwmon_sensor_types type, |
| u32 attr, int channel, long *val) |
| { |
| switch (type) { |
| case hwmon_temp: |
| return pvt_read_temp(dev, attr, channel, val); |
| case hwmon_in: |
| return pvt_read_in(dev, attr, channel, val); |
| default: |
| return -EOPNOTSUPP; |
| } |
| } |
| |
| static const u32 pvt_chip_config[] = { |
| HWMON_C_REGISTER_TZ, |
| 0 |
| }; |
| |
| static const struct hwmon_channel_info pvt_chip = { |
| .type = hwmon_chip, |
| .config = pvt_chip_config, |
| }; |
| |
| static struct hwmon_channel_info pvt_temp = { |
| .type = hwmon_temp, |
| }; |
| |
| static struct hwmon_channel_info pvt_in = { |
| .type = hwmon_in, |
| }; |
| |
| static const struct hwmon_ops pvt_hwmon_ops = { |
| .is_visible = pvt_is_visible, |
| .read = pvt_read, |
| }; |
| |
| static struct hwmon_chip_info pvt_chip_info = { |
| .ops = &pvt_hwmon_ops, |
| }; |
| |
| static int pvt_init(struct pvt_device *pvt) |
| { |
| u16 sys_freq, key, middle, low = 4, high = 8; |
| struct regmap *t_map = pvt->t_map; |
| struct regmap *p_map = pvt->p_map; |
| struct regmap *v_map = pvt->v_map; |
| u32 t_num = pvt->t_num; |
| u32 p_num = pvt->p_num; |
| u32 v_num = pvt->v_num; |
| u32 clk_synth, val; |
| int ret; |
| |
| sys_freq = clk_get_rate(pvt->clk) / HZ_PER_MHZ; |
| while (high >= low) { |
| middle = (low + high + 1) / 2; |
| key = DIV_ROUND_CLOSEST(sys_freq, middle); |
| if (key > CLK_SYS_CYCLES_MAX) { |
| low = middle + 1; |
| continue; |
| } else if (key < CLK_SYS_CYCLES_MIN) { |
| high = middle - 1; |
| continue; |
| } else { |
| break; |
| } |
| } |
| |
| /* |
| * The system supports 'clk_sys' to 'clk_ip' frequency ratios |
| * from 2:1 to 512:1 |
| */ |
| key = clamp_val(key, CLK_SYS_CYCLES_MIN, CLK_SYS_CYCLES_MAX) - 2; |
| |
| clk_synth = ((key + 1) >> 1) << CLK_SYNTH_LO_SFT | |
| (key >> 1) << CLK_SYNTH_HI_SFT | |
| (key >> 1) << CLK_SYNTH_HOLD_SFT | CLK_SYNTH_EN; |
| |
| pvt->ip_freq = sys_freq * 100 / (key + 2); |
| |
| if (t_num) { |
| ret = regmap_write(t_map, SDIF_SMPL_CTRL, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, SDIF_HALT, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, CLK_SYNTH, clk_synth); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(t_map, SDIF_DISABLE, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = CFG0_MODE_2 | CFG0_PARALLEL_OUT | CFG0_12_BIT | |
| IP_CFG << SDIF_ADDR_SFT | SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = POWER_DELAY_CYCLE_256 | IP_TMR << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(t_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | |
| IP_CTRL << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(t_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| } |
| |
| if (p_num) { |
| ret = regmap_write(p_map, SDIF_HALT, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(p_map, SDIF_DISABLE, BIT(p_num) - 1); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(p_map, CLK_SYNTH, clk_synth); |
| if(ret < 0) |
| return ret; |
| } |
| |
| if (v_num) { |
| ret = regmap_write(v_map, SDIF_SMPL_CTRL, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, SDIF_HALT, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, CLK_SYNTH, clk_synth); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_write(v_map, SDIF_DISABLE, 0x0); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = CFG1_VOL_MEAS_MODE | CFG1_PARALLEL_OUT | |
| CFG1_14_BIT | IP_CFG << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = POWER_DELAY_CYCLE_64 | IP_TMR << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| |
| ret = regmap_read_poll_timeout(v_map, SDIF_STAT, |
| val, !(val & SDIF_BUSY), |
| PVT_POLL_DELAY_US, |
| PVT_POLL_TIMEOUT_US); |
| if (ret) |
| return ret; |
| |
| val = IP_RST_REL | IP_RUN_CONT | IP_AUTO | IP_VM_MODE | |
| IP_CTRL << SDIF_ADDR_SFT | |
| SDIF_WRN_W | SDIF_PROG; |
| ret = regmap_write(v_map, SDIF_W, val); |
| if(ret < 0) |
| return ret; |
| } |
| |
| return 0; |
| } |
| |
| static struct regmap_config pvt_regmap_config = { |
| .reg_bits = 32, |
| .reg_stride = 4, |
| .val_bits = 32, |
| }; |
| |
| static int pvt_get_regmap(struct platform_device *pdev, char *reg_name, |
| struct pvt_device *pvt) |
| { |
| struct device *dev = &pdev->dev; |
| struct regmap **reg_map; |
| void __iomem *io_base; |
| |
| if (!strcmp(reg_name, "common")) |
| reg_map = &pvt->c_map; |
| else if (!strcmp(reg_name, "ts")) |
| reg_map = &pvt->t_map; |
| else if (!strcmp(reg_name, "pd")) |
| reg_map = &pvt->p_map; |
| else if (!strcmp(reg_name, "vm")) |
| reg_map = &pvt->v_map; |
| else |
| return -EINVAL; |
| |
| io_base = devm_platform_ioremap_resource_byname(pdev, reg_name); |
| if (IS_ERR(io_base)) |
| return PTR_ERR(io_base); |
| |
| pvt_regmap_config.name = reg_name; |
| *reg_map = devm_regmap_init_mmio(dev, io_base, &pvt_regmap_config); |
| if (IS_ERR(*reg_map)) { |
| dev_err(dev, "failed to init register map\n"); |
| return PTR_ERR(*reg_map); |
| } |
| |
| return 0; |
| } |
| |
| static void pvt_clk_disable(void *data) |
| { |
| struct pvt_device *pvt = data; |
| |
| clk_disable_unprepare(pvt->clk); |
| } |
| |
| static int pvt_clk_enable(struct device *dev, struct pvt_device *pvt) |
| { |
| int ret; |
| |
| ret = clk_prepare_enable(pvt->clk); |
| if (ret) |
| return ret; |
| |
| return devm_add_action_or_reset(dev, pvt_clk_disable, pvt); |
| } |
| |
| static void pvt_reset_control_assert(void *data) |
| { |
| struct pvt_device *pvt = data; |
| |
| reset_control_assert(pvt->rst); |
| } |
| |
| static int pvt_reset_control_deassert(struct device *dev, struct pvt_device *pvt) |
| { |
| int ret; |
| |
| ret = reset_control_deassert(pvt->rst); |
| if (ret) |
| return ret; |
| |
| return devm_add_action_or_reset(dev, pvt_reset_control_assert, pvt); |
| } |
| |
| static int mr75203_probe(struct platform_device *pdev) |
| { |
| const struct hwmon_channel_info **pvt_info; |
| u32 ts_num, vm_num, pd_num, val, index, i; |
| struct device *dev = &pdev->dev; |
| u32 *temp_config, *in_config; |
| struct device *hwmon_dev; |
| struct pvt_device *pvt; |
| int ret; |
| |
| pvt = devm_kzalloc(dev, sizeof(*pvt), GFP_KERNEL); |
| if (!pvt) |
| return -ENOMEM; |
| |
| ret = pvt_get_regmap(pdev, "common", pvt); |
| if (ret) |
| return ret; |
| |
| pvt->clk = devm_clk_get(dev, NULL); |
| if (IS_ERR(pvt->clk)) |
| return dev_err_probe(dev, PTR_ERR(pvt->clk), "failed to get clock\n"); |
| |
| ret = pvt_clk_enable(dev, pvt); |
| if (ret) { |
| dev_err(dev, "failed to enable clock\n"); |
| return ret; |
| } |
| |
| pvt->rst = devm_reset_control_get_exclusive(dev, NULL); |
| if (IS_ERR(pvt->rst)) |
| return dev_err_probe(dev, PTR_ERR(pvt->rst), |
| "failed to get reset control\n"); |
| |
| ret = pvt_reset_control_deassert(dev, pvt); |
| if (ret) |
| return dev_err_probe(dev, ret, "cannot deassert reset control\n"); |
| |
| ret = regmap_read(pvt->c_map, PVT_IP_CONFIG, &val); |
| if(ret < 0) |
| return ret; |
| |
| ts_num = (val & TS_NUM_MSK) >> TS_NUM_SFT; |
| pd_num = (val & PD_NUM_MSK) >> PD_NUM_SFT; |
| vm_num = (val & VM_NUM_MSK) >> VM_NUM_SFT; |
| pvt->t_num = ts_num; |
| pvt->p_num = pd_num; |
| pvt->v_num = vm_num; |
| val = 0; |
| if (ts_num) |
| val++; |
| if (vm_num) |
| val++; |
| if (!val) |
| return -ENODEV; |
| |
| pvt_info = devm_kcalloc(dev, val + 2, sizeof(*pvt_info), GFP_KERNEL); |
| if (!pvt_info) |
| return -ENOMEM; |
| pvt_info[0] = &pvt_chip; |
| index = 1; |
| |
| if (ts_num) { |
| ret = pvt_get_regmap(pdev, "ts", pvt); |
| if (ret) |
| return ret; |
| |
| temp_config = devm_kcalloc(dev, ts_num + 1, |
| sizeof(*temp_config), GFP_KERNEL); |
| if (!temp_config) |
| return -ENOMEM; |
| |
| memset32(temp_config, HWMON_T_INPUT, ts_num); |
| pvt_temp.config = temp_config; |
| pvt_info[index++] = &pvt_temp; |
| } |
| |
| if (pd_num) { |
| ret = pvt_get_regmap(pdev, "pd", pvt); |
| if (ret) |
| return ret; |
| } |
| |
| if (vm_num) { |
| u32 num = vm_num; |
| |
| ret = pvt_get_regmap(pdev, "vm", pvt); |
| if (ret) |
| return ret; |
| |
| pvt->vm_idx = devm_kcalloc(dev, vm_num, sizeof(*pvt->vm_idx), |
| GFP_KERNEL); |
| if (!pvt->vm_idx) |
| return -ENOMEM; |
| |
| ret = device_property_read_u8_array(dev, "intel,vm-map", |
| pvt->vm_idx, vm_num); |
| if (ret) { |
| num = 0; |
| } else { |
| for (i = 0; i < vm_num; i++) |
| if (pvt->vm_idx[i] >= vm_num || |
| pvt->vm_idx[i] == 0xff) { |
| num = i; |
| break; |
| } |
| } |
| |
| /* |
| * Incase intel,vm-map property is not defined, we assume |
| * incremental channel numbers. |
| */ |
| for (i = num; i < vm_num; i++) |
| pvt->vm_idx[i] = i; |
| |
| in_config = devm_kcalloc(dev, num + 1, |
| sizeof(*in_config), GFP_KERNEL); |
| if (!in_config) |
| return -ENOMEM; |
| |
| memset32(in_config, HWMON_I_INPUT, num); |
| in_config[num] = 0; |
| pvt_in.config = in_config; |
| |
| pvt_info[index++] = &pvt_in; |
| } |
| |
| ret = pvt_init(pvt); |
| if (ret) { |
| dev_err(dev, "failed to init pvt: %d\n", ret); |
| return ret; |
| } |
| |
| pvt_chip_info.info = pvt_info; |
| hwmon_dev = devm_hwmon_device_register_with_info(dev, "pvt", |
| pvt, |
| &pvt_chip_info, |
| NULL); |
| |
| return PTR_ERR_OR_ZERO(hwmon_dev); |
| } |
| |
| static const struct of_device_id moortec_pvt_of_match[] = { |
| { .compatible = "moortec,mr75203" }, |
| { } |
| }; |
| MODULE_DEVICE_TABLE(of, moortec_pvt_of_match); |
| |
| static struct platform_driver moortec_pvt_driver = { |
| .driver = { |
| .name = "moortec-pvt", |
| .of_match_table = moortec_pvt_of_match, |
| }, |
| .probe = mr75203_probe, |
| }; |
| module_platform_driver(moortec_pvt_driver); |
| |
| MODULE_LICENSE("GPL v2"); |