| /* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */ |
| /* |
| * Copyright (C) 2005-2014, 2018-2021 Intel Corporation |
| * Copyright (C) 2013-2015 Intel Mobile Communications GmbH |
| * Copyright (C) 2016 Intel Deutschland GmbH |
| */ |
| #ifndef __iwl_prph_h__ |
| #define __iwl_prph_h__ |
| #include <linux/bitfield.h> |
| |
| /* |
| * Registers in this file are internal, not PCI bus memory mapped. |
| * Driver accesses these via HBUS_TARG_PRPH_* registers. |
| */ |
| #define PRPH_BASE (0x00000) |
| #define PRPH_END (0xFFFFF) |
| |
| /* APMG (power management) constants */ |
| #define APMG_BASE (PRPH_BASE + 0x3000) |
| #define APMG_CLK_CTRL_REG (APMG_BASE + 0x0000) |
| #define APMG_CLK_EN_REG (APMG_BASE + 0x0004) |
| #define APMG_CLK_DIS_REG (APMG_BASE + 0x0008) |
| #define APMG_PS_CTRL_REG (APMG_BASE + 0x000c) |
| #define APMG_PCIDEV_STT_REG (APMG_BASE + 0x0010) |
| #define APMG_RFKILL_REG (APMG_BASE + 0x0014) |
| #define APMG_RTC_INT_STT_REG (APMG_BASE + 0x001c) |
| #define APMG_RTC_INT_MSK_REG (APMG_BASE + 0x0020) |
| #define APMG_DIGITAL_SVR_REG (APMG_BASE + 0x0058) |
| #define APMG_ANALOG_SVR_REG (APMG_BASE + 0x006C) |
| |
| #define APMS_CLK_VAL_MRB_FUNC_MODE (0x00000001) |
| #define APMG_CLK_VAL_DMA_CLK_RQT (0x00000200) |
| #define APMG_CLK_VAL_BSM_CLK_RQT (0x00000800) |
| |
| #define APMG_PS_CTRL_EARLY_PWR_OFF_RESET_DIS (0x00400000) |
| #define APMG_PS_CTRL_VAL_RESET_REQ (0x04000000) |
| #define APMG_PS_CTRL_MSK_PWR_SRC (0x03000000) |
| #define APMG_PS_CTRL_VAL_PWR_SRC_VMAIN (0x00000000) |
| #define APMG_PS_CTRL_VAL_PWR_SRC_VAUX (0x02000000) |
| #define APMG_SVR_VOLTAGE_CONFIG_BIT_MSK (0x000001E0) /* bit 8:5 */ |
| #define APMG_SVR_DIGITAL_VOLTAGE_1_32 (0x00000060) |
| |
| #define APMG_PCIDEV_STT_VAL_PERSIST_DIS (0x00000200) |
| #define APMG_PCIDEV_STT_VAL_L1_ACT_DIS (0x00000800) |
| #define APMG_PCIDEV_STT_VAL_WAKE_ME (0x00004000) |
| |
| #define APMG_RTC_INT_STT_RFKILL (0x10000000) |
| |
| /* Device system time */ |
| #define DEVICE_SYSTEM_TIME_REG 0xA0206C |
| |
| /* Device NMI register and value for 8000 family and lower hw's */ |
| #define DEVICE_SET_NMI_REG 0x00a01c30 |
| #define DEVICE_SET_NMI_VAL_DRV BIT(7) |
| /* Device NMI register and value for 9000 family and above hw's */ |
| #define UREG_NIC_SET_NMI_DRIVER 0x00a05c10 |
| #define UREG_NIC_SET_NMI_DRIVER_NMI_FROM_DRIVER BIT(24) |
| #define UREG_NIC_SET_NMI_DRIVER_RESET_HANDSHAKE (BIT(24) | BIT(25)) |
| |
| /* Shared registers (0x0..0x3ff, via target indirect or periphery */ |
| #define SHR_BASE 0x00a10000 |
| |
| /* Shared GP1 register */ |
| #define SHR_APMG_GP1_REG 0x01dc |
| #define SHR_APMG_GP1_REG_PRPH (SHR_BASE + SHR_APMG_GP1_REG) |
| #define SHR_APMG_GP1_WF_XTAL_LP_EN 0x00000004 |
| #define SHR_APMG_GP1_CHICKEN_BIT_SELECT 0x80000000 |
| |
| /* Shared DL_CFG register */ |
| #define SHR_APMG_DL_CFG_REG 0x01c4 |
| #define SHR_APMG_DL_CFG_REG_PRPH (SHR_BASE + SHR_APMG_DL_CFG_REG) |
| #define SHR_APMG_DL_CFG_RTCS_CLK_SELECTOR_MSK 0x000000c0 |
| #define SHR_APMG_DL_CFG_RTCS_CLK_INTERNAL_XTAL 0x00000080 |
| #define SHR_APMG_DL_CFG_DL_CLOCK_POWER_UP 0x00000100 |
| |
| /* Shared APMG_XTAL_CFG register */ |
| #define SHR_APMG_XTAL_CFG_REG 0x1c0 |
| #define SHR_APMG_XTAL_CFG_XTAL_ON_REQ 0x80000000 |
| |
| /* |
| * Device reset for family 8000 |
| * write to bit 24 in order to reset the CPU |
| */ |
| #define RELEASE_CPU_RESET (0x300C) |
| #define RELEASE_CPU_RESET_BIT BIT(24) |
| |
| /***************************************************************************** |
| * 7000/3000 series SHR DTS addresses * |
| *****************************************************************************/ |
| |
| #define SHR_MISC_WFM_DTS_EN (0x00a10024) |
| #define DTSC_CFG_MODE (0x00a10604) |
| #define DTSC_VREF_AVG (0x00a10648) |
| #define DTSC_VREF5_AVG (0x00a1064c) |
| #define DTSC_CFG_MODE_PERIODIC (0x2) |
| #define DTSC_PTAT_AVG (0x00a10650) |
| |
| |
| /** |
| * Tx Scheduler |
| * |
| * The Tx Scheduler selects the next frame to be transmitted, choosing TFDs |
| * (Transmit Frame Descriptors) from up to 16 circular Tx queues resident in |
| * host DRAM. It steers each frame's Tx command (which contains the frame |
| * data) into one of up to 7 prioritized Tx DMA FIFO channels within the |
| * device. A queue maps to only one (selectable by driver) Tx DMA channel, |
| * but one DMA channel may take input from several queues. |
| * |
| * Tx DMA FIFOs have dedicated purposes. |
| * |
| * For 5000 series and up, they are used differently |
| * (cf. iwl5000_default_queue_to_tx_fifo in iwl-5000.c): |
| * |
| * 0 -- EDCA BK (background) frames, lowest priority |
| * 1 -- EDCA BE (best effort) frames, normal priority |
| * 2 -- EDCA VI (video) frames, higher priority |
| * 3 -- EDCA VO (voice) and management frames, highest priority |
| * 4 -- unused |
| * 5 -- unused |
| * 6 -- unused |
| * 7 -- Commands |
| * |
| * Driver should normally map queues 0-6 to Tx DMA/FIFO channels 0-6. |
| * In addition, driver can map the remaining queues to Tx DMA/FIFO |
| * channels 0-3 to support 11n aggregation via EDCA DMA channels. |
| * |
| * The driver sets up each queue to work in one of two modes: |
| * |
| * 1) Scheduler-Ack, in which the scheduler automatically supports a |
| * block-ack (BA) window of up to 64 TFDs. In this mode, each queue |
| * contains TFDs for a unique combination of Recipient Address (RA) |
| * and Traffic Identifier (TID), that is, traffic of a given |
| * Quality-Of-Service (QOS) priority, destined for a single station. |
| * |
| * In scheduler-ack mode, the scheduler keeps track of the Tx status of |
| * each frame within the BA window, including whether it's been transmitted, |
| * and whether it's been acknowledged by the receiving station. The device |
| * automatically processes block-acks received from the receiving STA, |
| * and reschedules un-acked frames to be retransmitted (successful |
| * Tx completion may end up being out-of-order). |
| * |
| * The driver must maintain the queue's Byte Count table in host DRAM |
| * for this mode. |
| * This mode does not support fragmentation. |
| * |
| * 2) FIFO (a.k.a. non-Scheduler-ACK), in which each TFD is processed in order. |
| * The device may automatically retry Tx, but will retry only one frame |
| * at a time, until receiving ACK from receiving station, or reaching |
| * retry limit and giving up. |
| * |
| * The command queue (#4/#9) must use this mode! |
| * This mode does not require use of the Byte Count table in host DRAM. |
| * |
| * Driver controls scheduler operation via 3 means: |
| * 1) Scheduler registers |
| * 2) Shared scheduler data base in internal SRAM |
| * 3) Shared data in host DRAM |
| * |
| * Initialization: |
| * |
| * When loading, driver should allocate memory for: |
| * 1) 16 TFD circular buffers, each with space for (typically) 256 TFDs. |
| * 2) 16 Byte Count circular buffers in 16 KBytes contiguous memory |
| * (1024 bytes for each queue). |
| * |
| * After receiving "Alive" response from uCode, driver must initialize |
| * the scheduler (especially for queue #4/#9, the command queue, otherwise |
| * the driver can't issue commands!): |
| */ |
| #define SCD_MEM_LOWER_BOUND (0x0000) |
| |
| /** |
| * Max Tx window size is the max number of contiguous TFDs that the scheduler |
| * can keep track of at one time when creating block-ack chains of frames. |
| * Note that "64" matches the number of ack bits in a block-ack packet. |
| */ |
| #define SCD_WIN_SIZE 64 |
| #define SCD_FRAME_LIMIT 64 |
| |
| #define SCD_TXFIFO_POS_TID (0) |
| #define SCD_TXFIFO_POS_RA (4) |
| #define SCD_QUEUE_RA_TID_MAP_RATID_MSK (0x01FF) |
| |
| /* agn SCD */ |
| #define SCD_QUEUE_STTS_REG_POS_TXF (0) |
| #define SCD_QUEUE_STTS_REG_POS_ACTIVE (3) |
| #define SCD_QUEUE_STTS_REG_POS_WSL (4) |
| #define SCD_QUEUE_STTS_REG_POS_SCD_ACT_EN (19) |
| #define SCD_QUEUE_STTS_REG_MSK (0x017F0000) |
| |
| #define SCD_QUEUE_CTX_REG1_CREDIT (0x00FFFF00) |
| #define SCD_QUEUE_CTX_REG1_SUPER_CREDIT (0xFF000000) |
| #define SCD_QUEUE_CTX_REG1_VAL(_n, _v) FIELD_PREP(SCD_QUEUE_CTX_REG1_ ## _n, _v) |
| |
| #define SCD_QUEUE_CTX_REG2_WIN_SIZE (0x0000007F) |
| #define SCD_QUEUE_CTX_REG2_FRAME_LIMIT (0x007F0000) |
| #define SCD_QUEUE_CTX_REG2_VAL(_n, _v) FIELD_PREP(SCD_QUEUE_CTX_REG2_ ## _n, _v) |
| |
| #define SCD_GP_CTRL_ENABLE_31_QUEUES BIT(0) |
| #define SCD_GP_CTRL_AUTO_ACTIVE_MODE BIT(18) |
| |
| /* Context Data */ |
| #define SCD_CONTEXT_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x600) |
| #define SCD_CONTEXT_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x6A0) |
| |
| /* Tx status */ |
| #define SCD_TX_STTS_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x6A0) |
| #define SCD_TX_STTS_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x7E0) |
| |
| /* Translation Data */ |
| #define SCD_TRANS_TBL_MEM_LOWER_BOUND (SCD_MEM_LOWER_BOUND + 0x7E0) |
| #define SCD_TRANS_TBL_MEM_UPPER_BOUND (SCD_MEM_LOWER_BOUND + 0x808) |
| |
| #define SCD_CONTEXT_QUEUE_OFFSET(x)\ |
| (SCD_CONTEXT_MEM_LOWER_BOUND + ((x) * 8)) |
| |
| #define SCD_TX_STTS_QUEUE_OFFSET(x)\ |
| (SCD_TX_STTS_MEM_LOWER_BOUND + ((x) * 16)) |
| |
| #define SCD_TRANS_TBL_OFFSET_QUEUE(x) \ |
| ((SCD_TRANS_TBL_MEM_LOWER_BOUND + ((x) * 2)) & 0xfffc) |
| |
| #define SCD_BASE (PRPH_BASE + 0xa02c00) |
| |
| #define SCD_SRAM_BASE_ADDR (SCD_BASE + 0x0) |
| #define SCD_DRAM_BASE_ADDR (SCD_BASE + 0x8) |
| #define SCD_AIT (SCD_BASE + 0x0c) |
| #define SCD_TXFACT (SCD_BASE + 0x10) |
| #define SCD_ACTIVE (SCD_BASE + 0x14) |
| #define SCD_QUEUECHAIN_SEL (SCD_BASE + 0xe8) |
| #define SCD_CHAINEXT_EN (SCD_BASE + 0x244) |
| #define SCD_AGGR_SEL (SCD_BASE + 0x248) |
| #define SCD_INTERRUPT_MASK (SCD_BASE + 0x108) |
| #define SCD_GP_CTRL (SCD_BASE + 0x1a8) |
| #define SCD_EN_CTRL (SCD_BASE + 0x254) |
| |
| /*********************** END TX SCHEDULER *************************************/ |
| |
| /* Oscillator clock */ |
| #define OSC_CLK (0xa04068) |
| #define OSC_CLK_FORCE_CONTROL (0x8) |
| |
| #define FH_UCODE_LOAD_STATUS (0x1AF0) |
| |
| /* |
| * Replacing FH_UCODE_LOAD_STATUS |
| * This register is writen by driver and is read by uCode during boot flow. |
| * Note this address is cleared after MAC reset. |
| */ |
| #define UREG_UCODE_LOAD_STATUS (0xa05c40) |
| #define UREG_CPU_INIT_RUN (0xa05c44) |
| |
| #define LMPM_SECURE_UCODE_LOAD_CPU1_HDR_ADDR (0x1E78) |
| #define LMPM_SECURE_UCODE_LOAD_CPU2_HDR_ADDR (0x1E7C) |
| |
| #define LMPM_SECURE_CPU1_HDR_MEM_SPACE (0x420000) |
| #define LMPM_SECURE_CPU2_HDR_MEM_SPACE (0x420400) |
| |
| #define LMAC2_PRPH_OFFSET (0x100000) |
| |
| /* Rx FIFO */ |
| #define RXF_SIZE_ADDR (0xa00c88) |
| #define RXF_RD_D_SPACE (0xa00c40) |
| #define RXF_RD_WR_PTR (0xa00c50) |
| #define RXF_RD_RD_PTR (0xa00c54) |
| #define RXF_RD_FENCE_PTR (0xa00c4c) |
| #define RXF_SET_FENCE_MODE (0xa00c14) |
| #define RXF_LD_WR2FENCE (0xa00c1c) |
| #define RXF_FIFO_RD_FENCE_INC (0xa00c68) |
| #define RXF_SIZE_BYTE_CND_POS (7) |
| #define RXF_SIZE_BYTE_CNT_MSK (0x3ff << RXF_SIZE_BYTE_CND_POS) |
| #define RXF_DIFF_FROM_PREV (0x200) |
| #define RXF2C_DIFF_FROM_PREV (0x4e00) |
| |
| #define RXF_LD_FENCE_OFFSET_ADDR (0xa00c10) |
| #define RXF_FIFO_RD_FENCE_ADDR (0xa00c0c) |
| |
| /* Tx FIFO */ |
| #define TXF_FIFO_ITEM_CNT (0xa00438) |
| #define TXF_WR_PTR (0xa00414) |
| #define TXF_RD_PTR (0xa00410) |
| #define TXF_FENCE_PTR (0xa00418) |
| #define TXF_LOCK_FENCE (0xa00424) |
| #define TXF_LARC_NUM (0xa0043c) |
| #define TXF_READ_MODIFY_DATA (0xa00448) |
| #define TXF_READ_MODIFY_ADDR (0xa0044c) |
| |
| /* UMAC Internal Tx Fifo */ |
| #define TXF_CPU2_FIFO_ITEM_CNT (0xA00538) |
| #define TXF_CPU2_WR_PTR (0xA00514) |
| #define TXF_CPU2_RD_PTR (0xA00510) |
| #define TXF_CPU2_FENCE_PTR (0xA00518) |
| #define TXF_CPU2_LOCK_FENCE (0xA00524) |
| #define TXF_CPU2_NUM (0xA0053C) |
| #define TXF_CPU2_READ_MODIFY_DATA (0xA00548) |
| #define TXF_CPU2_READ_MODIFY_ADDR (0xA0054C) |
| |
| /* Radio registers access */ |
| #define RSP_RADIO_CMD (0xa02804) |
| #define RSP_RADIO_RDDAT (0xa02814) |
| #define RADIO_RSP_ADDR_POS (6) |
| #define RADIO_RSP_RD_CMD (3) |
| |
| /* LTR control (Qu only) */ |
| #define HPM_MAC_LTR_CSR 0xa0348c |
| #define HPM_MAC_LRT_ENABLE_ALL 0xf |
| /* also uses CSR_LTR_* for values */ |
| #define HPM_UMAC_LTR 0xa03480 |
| |
| /* FW monitor */ |
| #define MON_BUFF_SAMPLE_CTL (0xa03c00) |
| #define MON_BUFF_BASE_ADDR (0xa03c1c) |
| #define MON_BUFF_END_ADDR (0xa03c40) |
| #define MON_BUFF_WRPTR (0xa03c44) |
| #define MON_BUFF_CYCLE_CNT (0xa03c48) |
| /* FW monitor family 8000 and on */ |
| #define MON_BUFF_BASE_ADDR_VER2 (0xa03c1c) |
| #define MON_BUFF_END_ADDR_VER2 (0xa03c20) |
| #define MON_BUFF_WRPTR_VER2 (0xa03c24) |
| #define MON_BUFF_CYCLE_CNT_VER2 (0xa03c28) |
| #define MON_BUFF_SHIFT_VER2 (0x8) |
| /* FW monitor familiy AX210 and on */ |
| #define DBGC_CUR_DBGBUF_BASE_ADDR_LSB (0xd03c20) |
| #define DBGC_CUR_DBGBUF_BASE_ADDR_MSB (0xd03c24) |
| #define DBGC_CUR_DBGBUF_STATUS (0xd03c1c) |
| #define DBGC_DBGBUF_WRAP_AROUND (0xd03c2c) |
| #define DBGC_CUR_DBGBUF_STATUS_OFFSET_MSK (0x00ffffff) |
| #define DBGC_CUR_DBGBUF_STATUS_IDX_MSK (0x0f000000) |
| |
| #define MON_DMARB_RD_CTL_ADDR (0xa03c60) |
| #define MON_DMARB_RD_DATA_ADDR (0xa03c5c) |
| |
| #define DBGC_IN_SAMPLE (0xa03c00) |
| #define DBGC_OUT_CTRL (0xa03c0c) |
| |
| /* M2S registers */ |
| #define LDBG_M2S_BUF_WPTR (0xa0476c) |
| #define LDBG_M2S_BUF_WRAP_CNT (0xa04774) |
| #define LDBG_M2S_BUF_WPTR_VAL_MSK (0x000fffff) |
| #define LDBG_M2S_BUF_WRAP_CNT_VAL_MSK (0x000fffff) |
| |
| /* enable the ID buf for read */ |
| #define WFPM_PS_CTL_CLR 0xA0300C |
| #define WFMP_MAC_ADDR_0 0xA03080 |
| #define WFMP_MAC_ADDR_1 0xA03084 |
| #define LMPM_PMG_EN 0xA01CEC |
| #define RADIO_REG_SYS_MANUAL_DFT_0 0xAD4078 |
| #define RFIC_REG_RD 0xAD0470 |
| #define WFPM_CTRL_REG 0xA03030 |
| #define WFPM_CTRL_REG_GEN2 0xd03030 |
| #define WFPM_OTP_CFG1_ADDR 0x00a03098 |
| #define WFPM_OTP_CFG1_ADDR_GEN2 0x00d03098 |
| #define WFPM_OTP_CFG1_IS_JACKET_BIT BIT(4) |
| #define WFPM_OTP_CFG1_IS_CDB_BIT BIT(5) |
| |
| #define WFPM_GP2 0xA030B4 |
| |
| /* DBGI SRAM Register details */ |
| #define DBGI_SRAM_TARGET_ACCESS_CFG 0x00A2E14C |
| #define DBGI_SRAM_TARGET_ACCESS_CFG_RESET_ADDRESS_MSK 0x10000 |
| #define DBGI_SRAM_TARGET_ACCESS_RDATA_LSB 0x00A2E154 |
| #define DBGI_SRAM_TARGET_ACCESS_RDATA_MSB 0x00A2E158 |
| |
| enum { |
| ENABLE_WFPM = BIT(31), |
| WFPM_AUX_CTL_AUX_IF_MAC_OWNER_MSK = 0x80000000, |
| }; |
| |
| #define CNVI_AUX_MISC_CHIP 0xA200B0 |
| #define CNVR_AUX_MISC_CHIP 0xA2B800 |
| #define CNVR_SCU_SD_REGS_SD_REG_DIG_DCDC_VTRIM 0xA29890 |
| #define CNVR_SCU_SD_REGS_SD_REG_ACTIVE_VDIG_MIRROR 0xA29938 |
| |
| #define PREG_AUX_BUS_WPROT_0 0xA04CC0 |
| |
| /* device family 9000 WPROT register */ |
| #define PREG_PRPH_WPROT_9000 0xA04CE0 |
| /* device family 22000 WPROT register */ |
| #define PREG_PRPH_WPROT_22000 0xA04D00 |
| |
| #define SB_MODIFY_CFG_FLAG 0xA03088 |
| #define SB_CPU_1_STATUS 0xA01E30 |
| #define SB_CPU_2_STATUS 0xA01E34 |
| #define UMAG_SB_CPU_1_STATUS 0xA038C0 |
| #define UMAG_SB_CPU_2_STATUS 0xA038C4 |
| #define UMAG_GEN_HW_STATUS 0xA038C8 |
| #define UREG_UMAC_CURRENT_PC 0xa05c18 |
| #define UREG_LMAC1_CURRENT_PC 0xa05c1c |
| #define UREG_LMAC2_CURRENT_PC 0xa05c20 |
| |
| /* For UMAG_GEN_HW_STATUS reg check */ |
| enum { |
| UMAG_GEN_HW_IS_FPGA = BIT(1), |
| }; |
| |
| /* FW chicken bits */ |
| #define LMPM_CHICK 0xA01FF8 |
| enum { |
| LMPM_CHICK_EXTENDED_ADDR_SPACE = BIT(0), |
| }; |
| |
| /* FW chicken bits */ |
| #define LMPM_PAGE_PASS_NOTIF 0xA03824 |
| enum { |
| LMPM_PAGE_PASS_NOTIF_POS = BIT(20), |
| }; |
| |
| /* |
| * CRF ID register |
| * |
| * type: bits 0-11 |
| * reserved: bits 12-18 |
| * slave_exist: bit 19 |
| * dash: bits 20-23 |
| * step: bits 24-26 |
| * flavor: bits 27-31 |
| */ |
| #define REG_CRF_ID_TYPE(val) (((val) & 0x00000FFF) >> 0) |
| #define REG_CRF_ID_SLAVE(val) (((val) & 0x00080000) >> 19) |
| #define REG_CRF_ID_DASH(val) (((val) & 0x00F00000) >> 20) |
| #define REG_CRF_ID_STEP(val) (((val) & 0x07000000) >> 24) |
| #define REG_CRF_ID_FLAVOR(val) (((val) & 0xF8000000) >> 27) |
| |
| #define UREG_CHICK (0xA05C00) |
| #define UREG_CHICK_MSI_ENABLE BIT(24) |
| #define UREG_CHICK_MSIX_ENABLE BIT(25) |
| |
| #define SD_REG_VER 0xa29600 |
| #define SD_REG_VER_GEN2 0x00a2b800 |
| |
| #define REG_CRF_ID_TYPE_JF_1 0x201 |
| #define REG_CRF_ID_TYPE_JF_2 0x202 |
| #define REG_CRF_ID_TYPE_HR_CDB 0x503 |
| #define REG_CRF_ID_TYPE_HR_NONE_CDB 0x504 |
| #define REG_CRF_ID_TYPE_HR_NONE_CDB_1X1 0x501 |
| #define REG_CRF_ID_TYPE_HR_NONE_CDB_CCP 0x532 |
| #define REG_CRF_ID_TYPE_GF 0x410 |
| #define REG_CRF_ID_TYPE_GF_TC 0xF08 |
| #define REG_CRF_ID_TYPE_MR 0x810 |
| #define REG_CRF_ID_TYPE_FM 0x910 |
| |
| #define HPM_DEBUG 0xA03440 |
| #define PERSISTENCE_BIT BIT(12) |
| #define PREG_WFPM_ACCESS BIT(12) |
| |
| #define HPM_HIPM_GEN_CFG 0xA03458 |
| #define HPM_HIPM_GEN_CFG_CR_PG_EN BIT(0) |
| #define HPM_HIPM_GEN_CFG_CR_SLP_EN BIT(1) |
| #define HPM_HIPM_GEN_CFG_CR_FORCE_ACTIVE BIT(10) |
| |
| #define UREG_DOORBELL_TO_ISR6 0xA05C04 |
| #define UREG_DOORBELL_TO_ISR6_NMI_BIT BIT(0) |
| #define UREG_DOORBELL_TO_ISR6_RESET_HANDSHAKE (BIT(0) | BIT(1)) |
| #define UREG_DOORBELL_TO_ISR6_SUSPEND BIT(18) |
| #define UREG_DOORBELL_TO_ISR6_RESUME BIT(19) |
| #define UREG_DOORBELL_TO_ISR6_PNVM BIT(20) |
| |
| #define CNVI_MBOX_C 0xA3400C |
| |
| #define FSEQ_ERROR_CODE 0xA340C8 |
| #define FSEQ_TOP_INIT_VERSION 0xA34038 |
| #define FSEQ_CNVIO_INIT_VERSION 0xA3403C |
| #define FSEQ_OTP_VERSION 0xA340FC |
| #define FSEQ_TOP_CONTENT_VERSION 0xA340F4 |
| #define FSEQ_ALIVE_TOKEN 0xA340F0 |
| #define FSEQ_CNVI_ID 0xA3408C |
| #define FSEQ_CNVR_ID 0xA34090 |
| |
| #define IWL_D3_SLEEP_STATUS_SUSPEND 0xD3 |
| #define IWL_D3_SLEEP_STATUS_RESUME 0xD0 |
| |
| #define WMAL_INDRCT_RD_CMD1_OPMOD_POS 28 |
| #define WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK 0xFFFFF |
| #define WMAL_CMD_READ_BURST_ACCESS 2 |
| #define WMAL_MRSPF_1 0xADFC20 |
| #define WMAL_INDRCT_RD_CMD1 0xADFD44 |
| #define WMAL_INDRCT_CMD1 0xADFC14 |
| #define WMAL_INDRCT_CMD(addr) \ |
| ((WMAL_CMD_READ_BURST_ACCESS << WMAL_INDRCT_RD_CMD1_OPMOD_POS) | \ |
| ((addr) & WMAL_INDRCT_RD_CMD1_BYTE_ADDRESS_MSK)) |
| |
| #define WFPM_LMAC1_PS_CTL_RW 0xA03380 |
| #define WFPM_LMAC2_PS_CTL_RW 0xA033C0 |
| #define WFPM_PS_CTL_RW_PHYRF_PD_FSM_CURSTATE_MSK 0x0000000F |
| #define WFPM_PHYRF_STATE_ON 5 |
| #define HBUS_TIMEOUT 0xA5A5A5A1 |
| #define WFPM_DPHY_OFF 0xDF10FF |
| |
| #endif /* __iwl_prph_h__ */ |
